Preva Dental X
Contents
1. 4 Tape the mounting template to the wall 5 Using an awl or other sharp object punch through the mounting template to mark the location of the mounting holes 6 Drill 5 32 pilot holes for common pine studs at marked locations 7 Remove the mounting template from the wall and save for future use Install the Wall In the dual wood wall stud installation the Control Unit is bolted to a wall plate Plate 30 A2042 that has been installed on two wood studs The wall plate shown in Figure 15 is shipped separately from the Preva ll 26 Select the 3 8 inch 3 inch long lag screws and washers Put the lag screws and washers through the mounting holes on the wall plate and loosely tighten Be sure that the power wire extends through the opening in the wall plate Level the wall plate Tighten the lag screws to 14 to 18 ft lbs CAUTION Do not over tighten the lag screws Over tightening the lag screws will damage the wooden stud and reduce the holding force d progeny Installation Procedures Figure 15 Mounting Plate for Dual Stud Wall Mounts Remove Control Unit Front Cover Mount the Control Unit 2 aPN N n Preva Open the shipping carton and locate the Control Unit in the first level of the carton Remove the Phillips screw from the front cover of the Control Unit Carefully remove the front cover Place the front cover and the screw in a safe location for later reassembly2. Select the 5 16 inch 34 inch long socket cap screws and washers Put the upper screw and washer through the upper mounting hole of the Control Unit Place the Control Unit on the wall and loosely tighten the upper screw Put the lower screw and washer through the lower mounting hole of the Control Unit and loosely tighten Be sure that the power wire extends through the opening at the bottom of the Control Unit Place a level on the Control Unit bearing parallel to the wall Level the Control Unit Tighten the upper and lower screws After the Preva is installed slide covers on the wall plate and screw on g progeny 4 Micirmark Company Installation Procedures Preva Installing the Control Unit on a Metal Stud Wall Mark and Drill The mounting template is a guide for locating where to drill the holes used to Wall Plate and mount the wall plate and support plate to the wall Carefully placing the mounting Support Plate template on the wall will help ensure correct installation of these plates and hence of the Control Unit Mounting Holes 1 Using a stud finder locate the center of the stud on which the Control Unit will be mounted 2 Place the mounting template for the dual stud mount on the wall with the lower mounting holes 40 inches above the floor 3 Placea level parallel to the vertical lines on the mounting template and adjust the mounting template until it is plumb 4 Tape the mounting template to the wall 5 Using an
3. 30 Installing the Articulating Arm and Tubehead Aesemblhy 32 Sie ig ieneBig ale OS NETT 34 ade Ri A T TU 38 Mechanical e TEE 41 Installing the Control Unit Front Cover and the Operator Panel 42 Vi Sea UNIS te STOO A 46 saco 47 Checking System Functions nennen nnne nnne nans 48 System FUNCTION e e EE 49 Tube SEASONING Procedure nennen nennen nnns nn nnns sena nnne nnns 50 Refer to Page 62 for the Calibration procedure oocccccccoccconoccnccnncnnononncnnonennonnnnnnnnonanennnonanens 50 Optional Installation Procedures nnns 51 Installing the Coil cord Hand Switch Option GO A2OA0 51 Installing the Progeny Remote Exposure Station GO0 A20A4 53 Installing the 12 Inch Cone 30 A203B oooccccccccnccccnncococonocononoconcnnononnnnnonnnnonnnnnononononnnnnnnnnnnnnnos 58 Y Sle dC ORICA 110 PNE OO POO0PO0 N0UOS 5 N 05 E ESOO 59 System Gontiqura ton MoO G EE 59 PACS TN MS e enibiancions 60 Changing Pre programmed Exposure Settings ccooonccncccooccnnccnoccnncnnanoncnnnnnnnnonnancnnnonarennnnnns 61 Showing Current System Configuration cesses 62 Changing the Cone Size assess ar e iirorsetcobsen 63 Hadas det ee 64 FA NETTE TRETEN 65 Automated Calibration Procedures teet Eae Ren aoa Rin naa F aser aH ra FREE Eaa 65 FODOS NOOLI ts RN RR ironia 68 Electrical Performance TE 68 Ubtalmmida Technical 0 610 a E TET 87 clic e e UI O PP EE OE E E E 88 Preva Tubehead Removal Instructions eene nnns 88 Mechanical
4. 524 Fax 31 343 442 162 Safety Radiation Safety Only qualified and authorized personnel may operate this equipment observing all laws and regulations concerning radiation protection e The operator at all times must remain 6ft 2m from the focal spot and the x ray beam for operator protection e Full use must be made of all radiation safety features on the equipment e Full use must be made of all radiation protection devices accessories and procedures available to protect the patient and operator from x ray radiation Only qualified and authorized service personnel should remove covers on the equipment e This equipment must only be used in rooms or areas that comply with all applicable laws and recommendations concerning electrical safety in rooms used for medical purposes e g IEC US National Electrical code or VDE standards concerning provisions of an additional protective earth ground terminal for power supply connection e Before cleaning or disinfecting this equipment must always be disconnected from the main electrical supply e The Preva Dental X Ray System is ordinary type medical equipment without protection against ingress of liquids To protect against short circuit and corrosion no water or any other liquid should be allowed to leak inside the Electrical Safety equipment Explosion This equipment must not be used in the presence of flammable or potentially Safety explosive gases or vapors which could ignite
5. 75cm see note 2 see note 3 4g 39 121 92cm 99cm see note 4 note 2 7015 52 1 2 133 cm note 3 7015 56 1 2 143 5 cm 7016 62 1 2 159 cm 7016 66 1 2 169 cm 7017 72 1 2 184 cm 7017 76 1 2 194 5 cm 7018 78 1 2 199 cm 7018 82 1 2 209 5 cm With 12 30cm cone With 12 30cm cone note 3 7015 703 8 178 5cm d progeny 7016 80 3 8 204 cm a earmark Company 7017 903 8 229 5 cm 7018 963 8 244 5 cm Installation Options Figure 6 Retracted Position for a Cabinet Mount Preva 18 45 72cm with Compact Horizontal Arm 14 28 96 5 2cm with Short Horizontal 24 i 38 96 52cm with Long Horizontal Arm 34 1 27 j SU J 1 27cm U XA 2cm n Cabinet Outline 1 27 cm 82 reach not recommended for cabinet mount g proge dei A Moarark Con Installation Options Preva gt OS et IS sl in AO A nm m JS 56 143 26cm 2 112 27cm 23 58 42cm 59 T 149 9cm el iil m 57 1 145 03cm 35 9 91 18cm Figure 7 NS Y Mobile Unit e a 71 9 Extended 182 63cm Environmental Factors g progeny 10 A icimark Company Preva Installation Options Use Storage The Preva Dental X Ray System is intended for indoor use for normal dental applications at temperatures in the range 50 F 95 F 10 35 C and ata maximum altitude of 12 000 feet Humidity should not cause condensation to for
6. Adjustments occcccccncccnccnccnnnnnncncnnononcnnonannnonnnnnnnnnnnnnrnnnnnnnnnrnnnnrnnrnannnnnanennonarinenanos 92 Factory Default Exposure SettidgQS occcccoccccccnnnococonononnnononononanononannnonnnnononcnononcnononesns 98 Other Digital Exposure Settings occcccoccccconnnccononococnnonanononannnonnnnnnnnnnnnnnnnnnnnnnonnnnnnnnns 99 Replacement Hate 100 Amrana TUDENG I e o E E E E E 100 FO ZO e PP 101 LOU MUNG PLATOS arancel caia add 102 Oper F BLEU 104 Elne 0 EE 105 Hana W EE 106 io E 107 Preva Dental X Ray System cccccceeccccceeeeeeeceeeeeeeseeeeeceseeeeceeseeeeeeesseaeeesseeseeeessaeeeesaaeeees 107 Appendix a RR 109 Assembly Instructions for VetVision DC Mobile Un 109 POC 4 10 9 6 PORO AAPR OO POUR PO OCUPO PRO E P 121 Electronics Block Le ME 121 Installation Options Preva General Information Indications for Use The Preva Intraoral Dental X Ray is to be used as an extraoral source of x ray in Dental radiography Contraindications None known Product Description Control Unit Tubehead Articulating Arm Horizontal Arm Cone Remote Control Mobile Unit Installation and Service The Preva Dental X Ray System is a state of the art high frequency intra oral x ray machine The Preva consists of five components as shown in Figure 1 Component Diagram the Control Unit the Tubehead the Articulating Arm the Horizontal Arm the Cone and the Remote Contro
7. Installing the Articulating Arm and Tubehead Assembly g progeny 3 2 A Micirmark Company Installation Procedures Preva 1 Locate the Articulating Arm brake assembly 30 A2068 2 Insert the M6 x 25 mm long set screw as shown in Figure 20 Using a 3 mm Allen wrench tighten the screw fully than back off 1 4 and secure with the hex nut 3 Using a 3 mm Allen wrench install the Articulating Arm brake Tighten screws until the Articulating Arm brake comes into contact with the shaft of the Articulating Arm If additional friction is required to prevent drifting turn the two screws evenly turn at a time until drift stops as shown in Figure 21 Install the Articulating Arm Brake Assembly ae ge E 1 d eRe SH SSE ERE SESS ERP Figure 20 Installing the Hex Nut and Set Screw Figure 21 Adjusting the Articulating Arm Brake Assembly SCH 33 Installation Procedures Preva Connecting the Cables Connecting 1 Connect the two Articulating Arm cables to the Horizontal Arm cables as shown in the Figure 22 and 22A 2 Once the connections are made dress the cables and push into the opening in the Horizontal Arm Articulating and Horizontal Arm Cables Figure 22 Connecting the Articulating Arm and Horizontal Arm Cables Figure 22A Connecting optional Integrated Sensor Cable y progeny 34 A Miarmark Company Installation Procedures Preva Connectin ilie I CAUTION Horizont
8. Phillips Torque wrench 0 40 ft lbs or equivalent Sockets and ratchet driver appropriate to type of wall mounting Fluke model 73 DVM equivalent or better Small test clips such as Pomona Electronics Minigrabber Test Clip Model 6248 or Radio Shack Mini Hook Adapters catalog 270 334 ltems needed only for the metal stud wall mount e 11 inch hole saw Dry wall saw Y inch diameter 12 inch long drill bit Two 4x4 wood studs Drywall screws The Preva Dental X Ray System has been designed to be installed by one person in less than one hour assuming that all pre installation requirements have been met The Preva Dental X Ray System is shipped in a convenient two level carton as shown in Figure 13 The first level contains the items needed for the first part of the installation including the Control Unit Operator Panel Horizontal Arm mounting template documentation cables and bags containing the mounting hardware brake assembly plastic covers and additional hardware The Articulating Arm and Tubehead Assembly is in the second level of the shipping carton where it can remain until it is installed g progeny Installation Procedures Figure 13 Two level Carton Packing List Preva Part Number Description Quantity 30 A1010 Articulating Arm and Tubehead Assembly 1 30 A1025 Control Unit Assembly 1 30 A2076 Operator Panel 1 30 P0029 Operator Panel Mounting Cradle 1 30 A2046 Preva Mounting Hardware Kit 1 30 A2156
9. Preva Plastic Covers Brake Kit 1 E1 13002 Line Cord 16 3 6 Wide 1 E1 13003 8 Cond RJ45 to RJ45 25 ft 1 E1 13004 8 Cond RJ45 to RJ45 6 in 1 30 A 2086 Preva Documentation Kit 1 Note Shipment Contains One of the Following Extension Arms Per Order 30 A207 1 Extension Arm Long 1 30 A2073 Extension Arm Short 1 30 A2074 Extension Arm Compact 1 30 A2164 Extension Arm Extra Long 1 Options E1 13034 8 Cond RJ45 to RJ45 50 ft 30 081 01 Doorbell Switch 30 A2044 Lighted Doorbell Switch 30 A2041 8 inch Rectangular Cone 22 11466 amm Adjustment Wrench 22 11467 Fluorescent Screen 30 A2042 16 inch Mounting Plate 00 02 0488 FDA Form 2579 30 A2100 Service Kit 30 A2099 4x4 Mount Kit 30 A2152 Series Exposure Switch Kit Installing the Control Unit on a Single Wood Stud Wall 23 g progeny 4 Mieimark Compary Installation Procedures Mark and Drill Control Unit Mounting Holes Remove Control Unit Front Cover Mount and Level the Control Unit 24 Preva WARNING UNDER NO CIRCUMSTANCES SHOULD THE 82 INCH 208 CM REACH SYSTEM BE ATTACHED TO A WALL IN THE SINGLE STUD CONFIGURATION PLEASE DIRECT ANY QUESTIONS ON THIS MATTER TO THE PROGENY TECHNICAL SUPPORT GROUP The mounting template is a guide for locating where to drill the holes used to mount the Control Unit to the wall Carefully placing the mounting template on the wall will help ensure correct installation of the Control Unit 1 Using a stud finder
10. causing personal injury and or damage to the equipment If such disinfectants are used the vapor must be allowed to disperse before using the equipment Explanation of Symbols on Technical Labels g progeny 1 4 A Miairnark Compar Installation Options Preva Type B Protection against electric shock IEC 60601 1 1 Consult written instructions in User s Manual ATTENTION RAYONS X OPERATION SEULEMENT PAR DU PERSONNEL AUTORISE VOIR MANUEL DE L OPERATEUR WARNING X RAY THIS X RAY UNIT MAY BE DANGEROUS TO PATIENT AND OPERATOR UNLESS SAFE EXPOSURE FACTORS AND OPERATING INSTRUCTIONS ARE OBSERVED lu X RAY EMISSION gt lt p gt Mains HOT WIRE Mains NEUTRAL WIRE Earth Ground zr Obtaining Technical Support Contact PROGENY A Midmark Company 675 Heathrow Dr Lincolnshire IL 60069 Phone 888 924 3800 Fax 847 415 9801 techsupport progenydental com 15 A Installation Options Preva Installation Options Mounting Configurations Mounting This section gives instructions for installing the Preva Dental X Ray System in three Template mounting configurations Use the mounting template shown in Figure 8 to guide single stud installations Reverse the template for dual stud installations g progeny WS PHEVA Figure 8 Mounting Template CAUTION When installing the intraoral system combined with the 82 inch 209 centimeter reach arm wall fabrication and attachment
11. determine the suitability of installing the Preva with a line cord If a line cord is used the installer must ensure that the unit is properly grounded and has the required line rating Nominal 110 230 VAC 10 g progeny Installation Options Preva Fuse Rating 5A 250V UL Recognized Max Line Nominal Voltage Line Resistance e 120 230 VA A oh Resistance 0 290 VA 0 4 ohm Compliance with Applicable Standards Radiation The certified components of the Preva Dental X Ray System comply with Radiation Protection Performance Standards 21 CFR Subchapter J at the time of manufacture The certified components of the Preva Dental X Ray System comply with IEC 60601 1 3 Radiation protection x ray equipment UL 2601 1 File Classified by Underwriters Laboratories Inc with respect to electrical shock fire and Number mechanical hazards only in accordance with UL 2601 1 and CAN CSA C22 2 NO 601 1 E181 750 M90 and to the following particular standards IEC60601 2 7 IEC60601 2 28 EMI EMC IEC60601 1 2 Certified Components System Component Reference Number Tubehead 30 A1027 Control Unit 30 A0010 Cone 8 in 30 A2016 Cone 12 in 30 A2033 Cone 8 in Rectangular 30 A2041 Cone 12 in Rectangular 30 A21 12 Cone 59mm 30 A2107 Cone 60 mm 30 A2101 g progeny 1 2 A Miairnark Compar Installation Options Preva EC Declaration of Conformity Name and Progeny Preva Description of Product Catalog P7018 82 inch reach Model 30 A0010 Con
12. lifting out Figure 17 Installing the Horizontal Arm g progeny 30 A Micirmark Company Installation Procedures Preva Figure 18 Installing the Brake Assembly ff progeny 3l Installation Procedures Preva Installing the Articulating Arm and Tubehead Assembly Install the The Tubehead and Articulating Arm are installed as a single unit Articulating Arm 1 Remove the top level packing material from the shipping carton to gain and Tub a ad access to the Articulating Arm and Tubehead Assembly Do not remove the cardboard tube enclosing the cable wires but remove the red tag Remove the Articulating Arm and Tubehead Assembly from the shipping carton Assembly o CAUTION Do not remove the tie holding the Articulating Arm closed Removing the tie will cause the Articulating Arm to spring open potentially causing personal injury Note Do not lubricate the shaft of the Articulating Arm or the bearings in the Control Unit 3 Position the Articulating Arm above the Horizontal Arm 4 Carefully route the cardboard tube with the arm cable plug through the opening in the Horizontal Arm 5 Insert the shaft of the Articulating Arm into the opening in the Horizontal Arm as shown in Figure 19 6 Press down until the shaft is completely seated in the Horizontal Arm 7 Remove the cardboard tube to free the wires Discard the cardboard tube 8 Untie the Articulating Arm and remove the plastic covering Figure 19
13. the connection identified as NEUT on the power strip 4 Attach a flanged spade and connect the ground green wire of the line to the connection identified as GND on the power strip 5 Leave the power line terminal strip cover off until the following electrical verification procedure is complete A PPPs ea ee a c Power Line Terminal Strip Cover Connector J1 Figure 24 Power Line Terminal Strip Cover Connecting During initial powerup and verification the Operator Panel is required Connect the the Operator Panel with the 25 ft interconnect cable Later you will connect the Operator Panel in its final position for use Operator 1 Identify the Operator Panel and the 25 ft interconnect cable Panel with 2 Plug the cable into the left socket at the base of the Operator Panel the 25 ft 3 Plug the other end of the cable into connector J1 on the Power Supply Control Cable Board 30 08043 as shown in Figure 24 g progeny 37 a iamar Cor elek Installation Procedures Preva Electrical Verification Calibration Calibration of the Preva Dental X Ray System is preset at the factory and is not required during initial installation Service replacement of the Power Supply Control Board 30 08043 or the Tubehead will require calibration See the Calibration section of this manual Verifying Input 1 Before turning on the system verify the input voltage by measuring the Voltage and voltage at LINE and NEUT as shown in Figure 25 The reading sh
14. the standard 8 inch Cone attached to the Tubehead A 12 inch Cone 30 A2033 can be ordered as an option An optional component the remote control switch is used to make exposures in addition to or replacing the use of the exposure button An optional device the mobile unit supports pre programmed technique selections and x ray acquisition See Appendix A for the installation instructions for the mobile unit The Preva Dental X Ray System should only be installed and serviced by approved Progeny dealer personnel Contact Progeny A Midmark Company at 888 924 3800 if you need assistance locating an approved dealer g progeny Installation Options CAUTIONS Preva When using lag screws as the method of attachment it is imperative to consider the full scope of the task Several factors must be considered for safe permanent installations Some of the key issues are Lumber commonly used in construction projects can be different from location to location The grade age position and overall condition can vary greatly The attachment stud may have additional hidden loads The location of the pilot hole with respect to the center of the stud will affect the load bearing ability The size of the pilot hole required for the lag screw will be different based on the grade age and condition of the lumber Never over tighten the lag screw as this will weaken the mechanical connection Lumber with splits or cracks should not be
15. 8 924 3800 Fax 847 415 9801 progenydental com g progeny A Midmark Company Preva Dental X Ray System Installation and Service Manual 00 02 1577 Rev T ECN P2043 Midmark Corporation 675 Heathrow Dr Lincolnshire Illinois 60069 U S A Phone 888 924 3800 Fax 847 415 9801 progenydental com Table of Contents Table f COMENS oe teneral IN lg ren caracas 3 Indications for Use aes 3 KS OPI UNI MONS emp ae TT 3 Product Ree O Merindad 3 Reach wie Re E Le NEP ITE mm 6 Environmental Pacto E 10 ooo AA A e 11 Electrical Fre CUM CT CTS A ES PUES ER A RE EA EAN EaR AAA 11 Compliance with Applicable Gtandarde nennen 12 Certified Components ccccceecccceeeeeceeceeeeeeeceeeeeeeseeeeeeeseseeeeeeeeeeeeeseeeeeesseaeeesseaeseessaeeeeesagases 12 EC Declaration of Coniormify nennen nnn nnne nnns nnn nnns 13 Authorized Representativas sssrinin nnua OT DO 14 E NEA EEE E E AE AA AE E A E E E 14 Explanation of Symbols on Technical Labele sees 14 OD ia mina Technical ele NE 15 MStala ton OPIO ees 16 MOOMIN CONGU ONS NETTE OT 16 Operator Panel LOCION TET To o mE 21 Ecco e e 22 Preparing to Install the Hreva enne nnne 22 Installing the Control Unit on a Single Wood Stud Wall 23 Installing the Control Unit on a Dual Wood Stud Wall 26 Installing the Control Unit on a Metal Stud Wall 28 Installing the Horizontal Arm and Brake Assembly oocccconcccocccccccnccncocnnnnnnnncnnnncnconcnonnnnnnnnnnos
16. CM REACH SYSTEM BE ATTACHED TO A WALL IN THE SINGLE STUD CONFIGURATION PLEASE DIRECT ANY QUESTIONS ON THIS MATTER TO THE PROGENY TECHNICAL SUPPORT GROUP g progeny Installation Options Dual Wood Stud Wall Figure 10 Dual Wood Stud Mount 18 Preva When installing the Preva Dental X Ray System on two 16 inch centered wood studs the Control Unit mounts to a wall plate Two Stud Mounting Kit 30 A2042 purchased as an option which mounts to the wood studs as shown in Figure 10 Fasteners are provided with the wall plate In mounting configurations using the dual stud wall plate there are several holes available for incoming line power This is to provide for various locations of existing power boxes when installing as a replacement unit Refer to the reverse side of the mounting template Figure 8 for hole locations g progeny A Micirmark Company Preva Installation Options Metal Stud Wall Figure 11 Metal Stud Mount 19 When installing the Preva Dental X Ray System on a metal stud wall the Control Unit mounts to a wall plate Two Stud Mounting Kit 30 A2042 purchased as an option and uses an additional support plate Metal Stud Support Plate Kit 30 A2043 purchased as an option positioned on the back end of the wall See Figure 11 Fasteners are provided with the wall plate and support plate The wall fabrication and attachments to the building structure must be capable of withstanding a load mome
17. al Verify that line power is disconnected before proceeding Arm Cables 1 Attach the black connector from the Horizontal Arm to point J4 of the Power Supply to the Control Board 30 08043 as shown in Figure 23 Power Note The plug must be properly oriented Be sure that the tabs on the connector Supply are down 2 Attach the white connector from the Horizontal Arm to point J1 on the Power Supply Board Board 30 08041 as shown in Figure 23 Note The plug must be properly oriented Be sure that the tabs on the connector are down Figure 23 Connecting the Horizontal Arm Cables to the Circuit Boards Optional 1 Optional integrated sensor cable Ty wrap the USB cable to the tie block Integrated provided as shown in Figure 23A Sensor g progeny 3 5 A Midmark Con el Installation Procedures Preva Attach provided tie block here loop and tie the cable to the tie block Figure 23A Tying optional sensor cable out of harms way g progeny 3 6 4 amak Company Installation Procedures Preva Connecting 1 Using a 3 mm Allen wrench remove the power line terminal strip cover at the base Line Power of the Power Supply Control Board to gain access to the power line terminal strip as shown in Figure 24 2 Attach a flanged spade and connect the hot black wire of the power line to the connection identified as LINE on the power strip 3 Attach a flanged spade and connect the neutral white wire of the line to
18. awl or other sharp object punch through the mounting template to mark the location of the mounting holes 6 Drill 4 inch pilot holes at marked locations 7 Drill 1 inch clearance holes 8 Remove the mounting template from the wall and save for future use Reinforce Metal Filler material is added to the wall to prevent the metal stud wall from being Stud Wall crushed during installation Ea 1 Cutan access hole 6 inches by 10 inches in size between the clearance holes 2 Insert two 4x4 wooden studs in the access hole Attach the studs to the rear drywall surface with drywall screws CAUTION The sheet metal stud wall must be secure to hold a load of 850 ft Ibs 118 kg m Assembling and In the metal wall stud installation the Control Unit is bolted to a wall plate Figure Mounting the 15 that has been installed to the support plate shown in Figure 16 The wall and Support Plate support plates are shipped separately from the Preva Put the small then the larger washers and nut on each of the four carriage 30 A2043 bolts 2 Insert the carriage bolts into the support plate holes 3 Screw the threaded standoffs onto the carriage bolts with the slotted ends away from the back plate 4 Place the plastic sleeve bearings in the slotted ends of the carriage bolts 5 Using a 5 32 Allen key insert a set screw into each threaded standoff Screw the set screw until just below the slot in the threaded standoff but do not tigh
19. ch of 66 inches Catalog P7017 with a 30 A2071 Horizontal Arm has a reach of 76 inches The diagrams show Catalog P7017 with a 76 inch reach For Catalog P7016 with a 66 inch reach reduce the dimensions by 10 inches For Catalog P7015 reduce the dimensions by 20 inches Optional 12 The 76 inch reach for Catalog P7017 assumes the use of the 8 inch Cone that is Inch Cone supplied with the system If the optional 12 inch Cone 30 A2033 is used the reach is reduced by 4 inches i i n 22 55 58 CM Min reach with Compact aa j Le B2 1 2 208 Dm Max reach wiih Exftralong Horizontal Arm 11 1 28 194 CM r Figure 2 f Reach and 12 Cone roduces reach by 4 Inches Coverage 10 16CM Diagram progeny Installation Options Preva i i 33 875 86cm i 92 5 Gef Clearance 35 5cm Height s 44 5 103cm 36 625 40 75 93cm 110cm 12 Cone 8 Cone 39 30cm 20cm 99cm Figure 3 Cabinet Mounting Dimensions 82 reach not recommended for cabinet mount g progeny Installation Options Figure 4 Retracted Wall Mount Figure 5 Extended Position Wall or Cabinet Mount 33 7 8 86cm 3 1 4 Preva B6 5 B 220 03 CM i Biz i 21 5cm see note 1 38 5 8 A 40 5 B TON All tel 7015 245 8 62 5cm CL 12 2 ar 7016 345 8 88cm KT STE 7017 445 8 114cm 7018 505 8 128 5cm I i pen o oe 5 08cm A 458 i 11
20. l option The Control Unit provides for the input power connection and control of the Tubehead and Operator Panel It provides automatic line voltage compensation kVp control and exposure time control The Control Unit consists of the mounting base and Operator Panel The Tubehead contains the x ray tube high voltage circuit and Cone The Tubehead is shipped already assembled to the Articulating Arm Note There is a small hole in the plastic handle covering the back of the Tubehead Under no circumstances should this hole be blocked as it provides an air vent to allow the Tubehead oil to expand and contract as the unit is operated The Articulating Arm provides the articulation support for the Tubehead and the reach and coverage of the Tubehead to the patient The Articulating Arm allows smooth movement for precise positioning and does not drift or vibrate when left in position The Horizontal Arm helps provide the necessary reach for the Preva The Horizontal Arm pivots smoothly around a shaft inserted in the top of the Control Unit The Horizontal Arm contains an access cover to connect the cable from the Horizontal Arm to the Control Unit The Horizontal Arm is available in four lengths providing reaches of 56 66 76 and 82 inches The Cone establishes the distance from the x ray tube to the patient s skin It provides positioning assistance and collimates the x ray beam to within a defined circle at its end The Preva is shipped with
21. locate the center of the stud on which the Control Unit will be mounted 2 Place the mounting template on the wall with the lower mounting hole 40 inches above the floor 3 Place a level parallel to the vertical lines on the mounting template and adjust the mounting template until it is plumb 4 Tape the mounting template to the wall 5 Using an awl or other sharp object punch through the mounting template to mark the location of the upper and lower mounting holes CAUTION It is very important that both mounting holes are in the center of the wood stud 6 Drill upper and lower 5 32 pilot holes for common pine studs at marked locations 7 Remove the mounting template from the wall and save for future use 1 Open the shipping carton and locate the Control Unit in the first level of the carton Remove the Phillips screw from the front cover of the Control Unit Carefully remove the front cover Place the front cover and the screw in a safe location for later reassembly ON 1 Select the 3 8 inch 3 inch long lag screws and washers Note For concrete walls the installer must supply the appropriate mounting bolts 2 Putthe upper lag screw and washer through the upper mounting hole of the Control Unit 3 Place the Control Unit on the wall and loosely tighten the upper mounting bolt 4 Putthe lower lag screw and washer through the lower mounting hole of the Control Unit and loosely tighten Be sure that the powe
22. m on the unit Storage temperature should not exceed the range 31 F 150 F 35 C 66 C Support Requirements The Preva Dental X Ray System is designed to mount on a single wood 2x4 inch drywall stud or equivalent wall support lt can also be mounted on concrete or other similar wall construction Mounting to a plywood or particle board wall is not acceptable Verifying the wall support capability and the selection of the proper mounting hardware is the responsibility of the installer Please note that a two stud wall plate assembly 30 A2042 is available as an option to mount on two wooden studs Assembly 30 A2043 is available as a metal stud mounting kit The wall support and mounting hardware for the Preva must withstand a 100 Ib 45 36 kg shear load and a 400 Ib 182 kg withdrawal force at each of the mounting bolts The wall fabrication and attachments to the building structure must be capable of withstanding a load moment of 850 ft lbs 118 kg m Electrical Requirements Main Power Supply Line Cord Use Line Voltage 11 The Preva Dental X Ray System requires a three wire electrician supplied power supply Two power lines Line LINE and Neutral NEUT and a Ground GND are required His recommended that the unit be installed with a dedicated electrical line connected to a breaker with a minimum 15 amp rating The wiring must provide for a permanently grounded power line configuration The installer must
23. nt of 850 ft lbs 118 kg m If the wall on which the Preva is to be installed does not meet this requirement it must be reinforced In mounting configurations using the dual stud wall plate there are several holes available for incoming line power This is to provide for various locations of existing power boxes when installing as a replacement unit Refer to the mounting template in Figure 8 for hole locations g progeny 4 amak Company Installation Options Preva Installing the The 4x4 Mount kit 30 A2099 shown in Figure 12 contains the items below 4x4 Mount Power line bracket Power cord cover Left conduit mounting plate Right conduit mounting plate 3 Phillips screws 6 nuts Instructions 1 Using the three Phillips screws secure the power line bracket to the power line cord cover 2 Place the right and left conduit mounting plates on the control 3 Place the assembled power line bracket and cord cover on the two bottom most threaded studs SSeS AAA cb Figure 12 4x4 Mount Cabinet Layout ld Lil 1 g progeny Installation Options Preva Operator Panel Locations The Operator Panel for the Preva Dental X Ray System can be installed on the Control Unit or mounted remotely on a wall On Control Unit The Operator Panel snaps on to the front of the Control Unit Installation of the Operator Panel on the Control Unit may require the purchase and use of the coil cord hand switch option 30 A2040 Rem
24. ote Operator The Operator Panel is mounted on the wall remote from the Control Unit Pans If the Operator Panel is mounted separate from the Control Unit a supplied cable must be run from the Control Panel to the Operator Panel Where local codes require a separate 2x4 junction box should be mounted to the left of the mounting stud above the power supply box Refer to the supplied mounting template for specific location g progeny 2 1 A Miairnark Comparn Installation Procedures Preparing to Install the Preva Check Pre installation Requirements Gather Tools Installation Time Open the Shipping Carton 22 Prior to beginning the installation be sure that all pre installation requirements have been completed This includes confirming that the wall support requirements are adequate for mounting the unit and that the electrical power requirements and wire locations are proper Note Progeny recommends that the Preva Dental X Ray System be connected to dedicated wiring and permanently grounded The installer must determine the suitability of using a line cord at the time of installation ensuring proper grounding technique Items needed for all types of mounts e Stud finder Bubble level torpedo level Masking or other tape for placing the mounting template on the wall Awl Drill driver and drill bits appropriate to type of wall mounting Metric Allen wrench set English inch Allen wrench set Screwdrivers flat blade and
25. ould be Turning On the within the range of 100 230V 10 2 Replace the power line terminal strip cover System 3 Turn on the Preva Dental X Ray System using the power switch as shown in Figure 26 On the Operator Panel Figure 27 you will see the product display screen showing the software version Then the Operator Panel will display the default technique factors A P F d Si j Zi a b nS T Ak AR ue A amp kl a i J Figure 25 Verifying Input Voltage at the Line Input g progeny 3 8 A Micirmark Company
26. r mounting hole of the Control Unit and loosely tighten Be sure that the power wire extends through the opening at the bottom of the Control Unit Place a level on the Control Unit bearing parallel to the wall Level the Control Unit Tighten the upper and lower screws After the Preva is installed slide covers on the wall plate and screw on g progen 4 amak Company Installation Procedures Preva Installing the Horizontal Arm and Brake Assembly Installing the 1 Locate the Horizontal Arm in the top level of the shipping carton Horizontal Arm 2 Remove the Horizontal Arm from the shipping carton Do not remove the and Brake cardboard tube around the wires bot remove the red tag Insert the cardboard tube snugly into the shaft of the Horizontal Arm Assembly Note Do not lubricate the shaft of the Horizontal Arm or bearings in Control Unit 3 Insert the cardboard tube enclosing the wires into the opening in the top of the Control Unit 4 Insert the Horizontal Arm completely into the Control Unit as shown in Figure 17 Ensure that the Horizontal Arm is firmly seated in place 5 Remove the cardboard tube to free the wires Discard the cardboard tube Note Do not make the wire connections at this time 6 Locate the brake assembly bag 30 A2049 As shown in Figure 18 install and loosely tighten the brake assembly in order to put a small amount of drag on the rotation of the Horizontal Arm and to keep the Horizontal Arm from
27. r wire extends through the opening at the bottom of the Control Unit 5 Place a level on the Control Unit bearing parallel to the wall as shown in Figure 14 Level the Control Unit 6 Tighten the upper and lower lag screws to 14 to 18 ft lbs 7 Predrill a hole for a 12 wood screw below the lower lag screw as shown in Figure 14 A Install and tighten the wood screw to prevent the unit from shifting CAUTION Do not over tighten the lag screws Over tightening the f progeny Installation Procedures Preva lag screws will damage the wooden stud and reduce the holding force Figure 14 Leveling the Control Unit For 12 Screw Figure 14 A g progeny 25 A Miarmark Company Installation Procedures Preva Installing the Control Unit on a Dual Wood Stud Wall Mark and Drill The mounting template is a guide for locating where to drill the holes used to Wall Plate mount the wall plate to the wall Carefully placing the mounting template for two Mounting Holes stud mount installations on the wall will help ensure correct installation of the mounting plate and hence the Control Unit 1 Using a stud finder locate the center of the studs on which the wall plate will be mounted 2 Place the mounting template for the two stud mount on the wall with the lower mounting holes 40 inches above the floor 3 Placea level parallel to the vertical lines on the mounting template and adjust the mounting template until it is plumb
28. s to the building structure must be capable of withstanding a load moment of 920 pounds 418 kilograms g progeny 1 6 A Miarmark Compar Installation Options Single Wood Stud Wall Solid Wall or Reinforced Wood Cabinet Figure 9 Wood Wall Stud Mount 17 Preva The Control Unit should be located at a height of 39 inches 99 cm from the floor to the bottom of the control mounted on the wood stud as shown in Figure 9 The large range of travel of the Articulating Arm provides some flexibility in the vertical position Two mounting holes are provided Refer to the supplied mounting template shown in Figure 8 for specific locations When installing in a reinforced wood cabinet refer to the manufacturer of the pass through box or cabinet for proper mounting configuration and height Refer to the supplied mounting template for specific locations of power supply and or Operator Panel cable access points In order to mount to a solid masonry type wall the same mounting holes and mounting template as the single wood wall stud are used The installer must supply appropriate fasteners The power supply 2x4 junction box should be mounted to the left of the mounting stud at the appropriate height as indicated in the mounting template Note A 4x4 junction box will not be covered by the Control Unit Refer to the supplied mounting template for specific location LES WARNING UNDER NO CIRCUMSTANCES SHOULD THE 82 INCH 208
29. ten 6 Using two sheet metal screws mount and level the support plate through the pilot holes on the back side of the wall Tighten the sheet metal screws with the screw driver 7 On the front side of the wall using a straight blade screw driver adjust the threaded standoffs until the plastic part is flush with the drywall 8 Tighten the set screws in the threaded standoffs to lock them in place g progeny 28 A Miairnark Compar Installation Procedures Figure 16 Support Plate for Metal Stud Wall Mount Install the Wall Plate 30 A2042 Remove Control Unit Front Cover Mount the Control Unit 29 N PON N Y Preva Select the 5 16 inch 1 inch long hex bolts Put the hex bolts through the mounting holes on the wall plate and loosely tighten Be sure that the power wire extends through the opening in the wall plate Level the wall plate Tighten the hex bolts Open the shipping carton and locate the Control Unit in the first level of the carton Remove the socket flathead screw from the front cover of the Control Unit Carefully remove the front cover Place the front cover and the screw in a safe location for later reassembly Select the 5 16 inch 34 inch long socket cap screws and washers Put the upper screw and washer through the upper mounting hole of the Control Unit Place the Control Unit on the wall and loosely tighten the upper screw Put the lower screw and washer through the lowe
30. trol 30 A2164 Extension Arm Extra Long Catalog P7017 76 inch reach Model 30 A0010 Control 30 A2071 Extension Arm Long Catalog P7016 66 inch reach Model 30 A0010 Control 30 A2073 Extension Arm Short Catalog P7015 56 inch reach Model 30 A0010 Control 30 A2074 Extension Arm Compact Catalog P7017 MG Mobile Model 30 A0010 Control Class IIb Reference The following regulatory documents apply Numbers to UL 2601 1 which IEC 60601 1 2 EM IEC 60601 1 3 Conformity is IEC 60601 2 7 Declared IEC 60601 2 28 IEC 60601 2 32 Medical Device Directive ISO 13485 FDA 510K File Number K043092 Declaration Midmark Corporation declares that the products described herein meet all the applicable Essential Requirements of the EC Medical Device Directive 93 42 EEC in Annex I For Class llb products described herein the product is manufactured inspected tested and released in accordance with the approved quality assurance system established in accordance with ISO 13485 and Annex Il of the EC Medical Device Directive under the Supervision of the SGS United Kingdom Ltd a Notified Body Contact Technical Support Progeny Inc techsupport progenydental com g progeny Installation Options Preva Authorized Representatives North America Midmark Corporation 675 Heathrow Dr Lincolnshire IL 60069 Phone 888 924 3800 Fax 847 415 9801 Europe CE Partner 4U Esdoornlaah 13 3951DB Maarn The Netherlands Phone 31 343 442
31. used for attachment Plywood particle board or similar construction materials should not be used for attachment Consider lumber dryness or moisture when attaching to exterior framing studs Progeny mechanical designs will exert up to 850 pounds 386 kilograms of loading on the supporting structure Progeny provides fasteners for average installations Based on specific installation conditions it may be necessary to choose a alternate fastener or fastening methods Seek the advice of a professional structural engineer to clarify any issues before the installation Inspect the attachment method 30 days after the installation and every 6 months thereafter f progeny Installation Options Preva Figure 1 Component Diagram Installation Options Preva Reach and Coverage The reach of the system is measured from the tip of the Cone with the arm fully extended and the Cone pointing back toward the pivot of the wall plate This measurement method accommodates the normal positioning of the Tubehead to the patient A patient can therefore be positioned without difficulty with the chair located within a radius outward from the pivot point to the dimensions shown in the diagrams Horizontal The Preva Horizontal Arm is available in three lengths Each length gives the system a Arm Lengths different reach Catalog P7015 with a 30 A2074 Horizontal Arm has a reach of 56 inches Catalog P7016 with a 30 A2073 Horizontal Arm has a rea
32. y progeny A Midmark Company Preva Dental X Ray System Installation and Service Manual KIT 30 A2086 00 02 1577 Rev T REV N ECN P2043 Attention The equipment must only be installed and operated in accordance with the safety procedures and operating instructions given in this manual and in the User Manual for the purposes and applications for which it was designed Modifications and or additions to the equipment may only be carried out by Progeny A Midmark Company or by third parties expressly authorized by Progeny Dental to do so Such changes must comply with legal requirements as well as with the generally accepted technical rules It is the responsibility of the user to ensure that existing legal regulations regarding installation of the equipment with respect to the building are observed X RAY PROTECTION X ray equipment may cause injury if used improperly The instructions contained in this manual must be read and followed when operating the Preva Your Progeny Dental dealer will assist you in placing the Preva in operation The Preva Dental X Ray System provides a high degree of protection from unnecessary x radiation However no practical design can provide complete protection nor prevent operators from exposing themselves or others to unnecessary radiation y progeny A Midmark Company More Than Imaging Excellence Midmark Corporation 675 Heathrow Drive Lincolnshire Illinois 60069 U S A Phone 88
Download Pdf Manuals
Related Search