P100 Pedestal and F100 Frame
Contents
1. 4 3 e 4 M4 hex nuts 4 Flat washers 66 4 10 Flat washers 8 4 e 10 M8 socket head cap screws e 4 M6 socket head cap screws e 2 Grommets 2 1 3 For LCD Video Wall Mounts and LCD Panels Refer to the ML10 MP10 40 65 LCD Video Wall Mount Instruction Sheet P N 020 100726 xx and the LCD Panel FHD551 X User Manual P N 020 100713 xx 2 2 Kits Required P100 LCD Pedestal P N 135 106108 xx F100 LCD Frame P N 135 105107 xx FHD551 X LCD Panel P N 135 001102 xx e Optional LCD Frame Trim 8ft P N 135 108100 xx 2 3 Tools and Hardware Required Level Phillips screwdriver 5mm allen key for attaching P100 Pedestals e 6mm ball driver metric screwdriver for attaching F100 Frames 24mm open ended adjustable wrench for tightening locknut on pedestal feet e 7mm open ended wrench for fastening extension hook e 2x 10mm open ended wrench for fastening pedestal to pedestal e 13mm open ended wrench for fastening frame to pedestal 2 4 Service and Support Trained service technicians are available to diagnose and correct system related problems If you encounter any problems during the setup and installation of your system contact the authorized dealer or Christie Partner from whom the system was purchased 2 2 Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 CH 1S TIE Section 2 Installation and Setup 2 5 Installation 2 5 1 Assemble the Pedestals VW NWT2. NOTES 1 Keeping the hardware a little loose at this point will allow you to tweak the alignment between pedestals as more are added to the platform 2 Do not completely tighten the hardware on the pedestal until the first row of frames are installed For more information refer to 2 5 2 Install Frames onto Pedestals on page 2 3 6 Slide the next pedestal into position and using a level adjust the height until the pedestal becomes level with the pedestals already in the row 7 Repeat steps 1 to 5 for each additional pedestal 8 Verify that the entire platform structure is level and that all rear edges between pedestals are flush NOTICE Apply downward pressure on the pedestal to ensure that the feet are flat to the floor 9 Do not completely tighten the hardware on the pedestal until the first row of frames are installed For more information refer to 2 5 2 Install Frames onto Pedestals on page 2 5 10 Once the pedestal assembly is constructed snap the panel caps into place see image below M6 hex head bolts Flat washer M6 hex nut Lock washer NOTE Front skin not shown in image for clarity Insert panel caps here 1 on each side Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 CH IS TIE Section 2 Installation and Setup 2 5 2 Install Frames onto Pedestals Stacked LCD panels can tip over and cause injury or damage when not properly secured The display wall must be supported during and
3. Out Comp Audio 599 30 400 00 Power Switch 686 10 Video In L Video S V RS232 In Rocker Type L Vide a Power R Video S V RS485 Out udio Connection Y A EEE NOTE Handles are hidden in this view for clarity Exhaust amp power supply location DO NOT obstruct the air flow 23 62 aa 600 00 A Handle x4 locations A DO NOT obstruct the air flow NOTE Illustrations shown as third angle projection Not to scale Pedestal and Frame Installation Manual A 1 020 100734 02 Rev 1 11 11 Appendix A Mechanical Drawings CHK IS TIE A 2 2x2 Configuration of Pedestal Frame and LCD Panel Minimum Image to Image Gap Dimension 2x2 Configuration of Pedestal Frame amp LCD Panel with Extended Mount for Service Pull Bracket Extension Hook on either side of panel to extend the display carriage N k 22 4 5 70 A 7 Pull strap to incline panel 11 57 294 8398 Panel Extended Out for Service Dimensions shown here is when corner adjustment knob in the mount is extended to 14mm 0 5 from its home position LCD Panel P N 135 001102 Frame P N 135 105107 General Notes 1 Refer to ML10 MP10 55 Spacer Kit Instruction Sheet P N 020 100728 xx for wall mount applications 2 Mounts frame pedestal shown here are for landscape orientation 3 Maximum stack height is 6 panels 4 Approximate weig
4. after installation to a structurally sound surface such as a permanent wall or an installer approved free standing external support structure e Neh gle 9 Lift equipment MUST be used to lift LCD panels into position on higher rows A crew of two can lift an LCD panel into position on the first row NOTICE Depending on the size of the wall assemble the frames starting at the center of the pedestal assemble working outwards to the end of each row 1 Position the first frame so that the 6 mounting points of the frame line up with the points on the pedestal 2 Loosely fasten the frame to the pedestal using 6 M8 socket head cap screws 12 washers and 6 M8 hex nuts NOTES 1 Keeping the hardware a little loose at this point will allow you to tweak the alignment between frames as more are added to the platform M8 socket head cap screw Flat washer Flat washer M8 hex nut Pedestal and Frame Installation Manual 2 5 020 100734 02 Rev 1 11 2011 Section 2 Installation and Setup CHA ISTIE 4 Using 4 M8 socket head cap screws and 4 flat washers 68 4 secure the 2 frames to one another using the 4 mounting points as shown below Hand tighten the hardware to allow small adjustments while the other frames are added to the row Flat washer M8 socket head cap screw Insert grommet here 1 on each side repeat for every row of frames Check the alignment between each frame and make adjustm
5. installer has the sole and final responsibility for ensuring that the system is installed with due regard for all relevant safety considerations Installation steps are described in sequence and each step must be completed before moving on to the next Components All major components required to assemble a complete display wall are packaged and shipped separately to the installation site This includes the LCD panels P100 Pedestals F100 Frames and the LCD video wall mounts Each component comes with the hardware required for installation Check the contents of your shipment against the list below to make sure that you have all the necessary hardware NOTE Trained service technicians are available to diagnose and correct system related problems If you encounter any problems during the setup and installation of your system contact the authorized dealer or Christie Partner from whom the system was purchased For P100 Pedestals Hardware Kit P N 000 102657 xx 2 Panel caps 16 Flat washers e 8 M6 hex nuts 06 5 e 8 M6 hex head bolt 8 Lock washers e 8 M8 socket head cap screws for securing frame to pedestal e 16 Flat washers 68 4 8 MS hex nuts for securing frame to pedestal Pedestal and Frame Installation Manual 2 1 020 100734 02 Rev 1 11 2011 Section 2 Installation and Setup CHA IS TIE 2 1 2 For F100 Frames Hardware Kit P N 000 102673 xx e 2 Bracket extension hooks e 4 Flat washers
6. 3 Once the pedestal platform is constructed it is essential an external support is constructed before adding the frames video wall mounts and LCD Panels to prevent the display from tipping and causing serious injuries to those at the installation site NOTICE Depending on the size of the wall assemble the platform beginning with the center pedestal working outwards to the end of each row 1 2 3 Slide 2 pedestals together aligning the front and rear edges Using a level adjust the 3 pedestal feet by rotating them until the 2 pedestals are level on all sides and with each other Use a 24mm open ended adjustable wrench to tighten the lock nut on the feet once the required adjustment is made Tighten lock nut once adjustments are made Inspect the inside corners of the pedestal to confirm that the pedestal feet remain fully engaged in the pedestal If you cannot see any threads at the top of the corner bracket where the foot is installed then you have over extended the pedestal foot and must correct this before moving on Using a phillips screwdriver loosen the 8 screws on the rear pedestal skin Slide the rear skin up and out to access the mounting points on the pedestal Pedestal and Frame Installation Manual 2 3 020 100734 02 Rev 1 11 2011 2 4 Section 2 Installation and Setup CHA ISTIE 5 Loosely fasten the 2 pedestals together using 4 M6 hex nuts 4 M6 hex head bolts 8 flat washers and 4 lock washers
7. Contents 1 Introduction 1 1 Using ts Meat di O 1 1 1 2 Labels and Marking ee ae 1 1 1 3 Typographical N tatians iia ion iii 1 1 1 4 Safety Warnings and Guidelines a AA AAA 1 2 14 1 Stackins Limit au0n8 nee 1 2 1 42 Using Christie P100 Pedale 1 2 1 4 3 External SUpport aa 1 2 1 4 4 Lif ng LCD Panels ee 1 2 14 Arto Cond OA candado 1 2 1 5 Contact Information aa ke ee 1 2 2 Installation and Setup 2 1 COMPE a EAEE E EEA EAEE ESE 2 1 2 1 1 For P100 Pedestals Hardware Kit P N 000 102657 XxX oooocoocccooococononoconnnoconanononononananonos 2 1 2 1 2 For F100 Frames Hardware Kit P N 000 102673 xx cccssscssessesssscessseceessseesneeeeens 2 2 2 1 3 For LCD Video Wall Mounts and LCD Panels osas 2 2 2 2 Kits e ooo cao ee a eae ca awe 2 2 2 3 Tools and Hardware Regie ass u 2 2 2 4 Service and SUPPO einteilen 2 2 2 5 Installation sunshine 2 3 25 1 Assemble th PSUS US ae 2 3 2 5 2 Install Frames onto Pedestals c scssccssanseacseentsecsscnscacanensesnsvsedsacsnanaseacsneasetspeetsacesausesoanensocness 2 5 2 5 3 Adding Additional Rows of F100 Frames iia 2 6 2 5 4 Install Video Wall Mount onto Frame cecceccccesceeseceseeeescecseecaeceseeeeceesseecaeceeeenaeenseenes 2 7 2 53 nstall FED ET LCD Parla 2 7 2 5 6 Apply Permanent External Support mida 2 7 2 5 1 Connect SOUTCES uch ia 2 8 Zas Optional Install TrM da 2 8 2 5 9 Optional Install Bracket Extension Hook ooooocccinocinococonoconcconnonncconn cono cono
8. P100 Pedestal and F100 Frame Installation Manual 020 100734 02 CHAISTIE P100 Pedestal and F100 Frame Installation Manual 020 100734 02 NOTICES COPYRIGHT AND TRADEMARKS 2011 Christie Digital Systems USA Inc All rights reserved All brand names and product names are trademarks registered trademarks or trade names of their respective holders GENERAL Every effort has been made to ensure accuracy however in some cases changes in the products or availability could occur which may not be reflected in this document Christie reserves the right to make changes to specifications at any time without notice Performance specifications are typical but may vary depending on conditions beyond Christie s control such as maintenance of the product in proper working conditions Performance specifications are based on information available at the time of printing Christie makes no warranty of any kind with regard to this material including but not limited to implied warranties of fitness for a particular purpose Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material The product is designed and manufactured with high quality materials and components that can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from regular waste Please dispose of t
9. ations are used throughout this manual e References to specific areas of the document appear italicized and underlined When viewed online the text appears in blue indicating a direct link to that section For example Section 1 Introduction e References to other documents appear italicized and bold such as Service Manual e References to software menus and available options appear bold such as Main menu Preferences e User input or messages that appear on screen in status display units or other control modules appear in Courier font For example No Signal Present Login christiedigital Error codes LED status appear in bold e g LP Al etc Operational states of modules appear capitalized such as power ON OFF e Pedestal and Frame Installation Manual 1 1 020 100734 02 Rev 1 11 2011 Section 1 Introduction SS CHI ESTE 1 4 1 4 1 1 4 2 1 4 3 1 4 4 1 4 5 1 5 1 2 Safety Warnings and Guidelines Please read the following warnings before commencing installation to ensure the safety ofthose working at the installation site Stacking Limitations Do not stack more than 6 F100 Frames when using the approved P100 Pedestals Stacking the frames higher than the recommended limit increases the possibility of the display wall becoming unstable and unsafe and also increases the chance that the pedestals may buckle from the extra weight Using Christie P100 Pedestals It is strongly rec
10. ay wall consider Local building codes for specific requirements e Size of the installation number of LCD panels being stacked e Physical characteristics of the installation including weight center of gravity mounting hole location See Section A Mechanical Drawings for technical information on display wall components e Type of material being considered for external support Strength and stability of the vertical or horizontal surface e Required number of external supports The illustration below depicts 2 possible external support methods for a display wall Consider your options and choose the method that best supports your specific installation CAUTION The natural frequency of support is dependant on the size of the wall and should be determined by a qualified installer Example of Ceiling Mount Support Example of Wall Mount Support Shown threaded rods installed into ceiling to support 2x2 wall Shown bars installed into back wall to support 2x2 wall Pedestal and Frame Installation Manual 2 7 020 100734 02 Rev 1 11 2011 Section 2 Installation and Setup CHA ISTIE 2 5 7 Connect Sources A variety of external sources can be connected to the connection panel on the LCD panel Properly routing the cables from 1 LCD panel to another in the display wall will keep them from becoming tangled For a detailed overview refer to the ML10 MP10 40 65 LCD Video Wall Mount Instruction Sheet P N 020 100726 xx an
11. cent to it Check alignment between each frame and adjust as required g Tighten all hardware between the top and bottom frames before adding the next row of frames h Snap grommets into the cutouts of the frames on each end of the row These grommets ensure the cables do not rub against the metal cutout see image above i Repeat the above steps to add additional rows of frames until the desired installation is complete Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 CHA ISTIE Section 2 Installation and Setup 2 5 4 Install Video Wall Mount onto Frame 2 5 5 For a detailed overview refer to the ML10 MP10 40 65 LCD Video Wall Mount Instruction Sheet P N 020 100726 xx and the LCD Panel FHD551 X User Manual P N 020 100713 xx Install FHD551 X LCD Panel For a detailed overview refer to the ML10 MP10 40 65 LCD Video Wall Mount Instruction Sheet P N 020 100726 xx and the LCD Panel FHD551 X User Manual P N 020 100713 xx 2 5 6 Apply Permanent External Support e 0 gle External support for a display wall must be designed and implemented by a qualified installer and must comply to local area safety standards All display walls must have permanent external supports The FHD551 X LCD panel display wall requires external support regardless of its overall height Reinforcing the structure prevents the wall from tipping due to unforeseen circumstances When designing external support for a displ
12. cio cono cnnn cono nconncns 2 8 A Mechanical Drawings EA A A reece E VERDERIETRERS A 1 A 2 2x2 Configuration of Pedestal Frame and LCD Panel ist A 2 As Attaching Pedestal and Frame A e A 3 Pedestal and Frame Installation Manual i 020 100734 02 Rev 1 CHAISTIE 1 Introduction Every effort has been made to ensure the information in this document is accurate and reliable however due to constant research the information in this document is subject to change without notice 1 1 Using this Manual INIA ANNE To prevent physical injury or equipment damage it is important Section 2 Installation and Setup is read in its entirety before installing this product This manual provides technical information for assisting qualified service technicians in the installation of the P100 Pedestal and F100 Frame 1 2 Labels and Marking Observe and follow any warnings and instructions marked on the projector WN e Danger symbols indicate a hazardous situation which if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations MN AN Ne Warning symbols indicate a hazardous situation which if not avoided could result in death or serious injury Yet Nile Caution symbols indicate a hazardous situation which if not avoided could result in minor or moderate injury NOTICE Addresses practices not related to personal injury 1 3 Typographical Notations The following not
13. d the LCD Panel FHD551 X User Manual P N 020 100713 xx 2 5 8 Optional Install Trim As an optional feature trim in the form of 8ft 2 4m magnetic strips can be applied to the sides of the display Each strip covers up to 3 frames in height 2 5 9 Optional Install Bracket Extension Hook To easily release individual panels installed into a display wall it is recommended the bracket extension hooks provided with the frame assembly are installed To install thread an M4 nut and flat washer onto the hook insert it into the video wall mount as shown in the illustration below Thread another flat washer and M4 nut onto the hook to secure it Use a 7mm open ended wrench to completely tighten the hardware Hardware Configuration Back View 2 8 Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 CHAISTIE A Mechanical Drawings Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 A 1 CHAISTIE Appendix A Mechanical Drawings A 1 LCD Panel A DO NOT obstruct the air flow 147 85 1215 30 M8 x 4 Mounting Holes f 4 28 Length of screw engagement 10mm min 15mm max 108 60 I Display Port HDMI 1 HDMI 2 DVI D In PC Audio In VGA In N DO NOT obstruct ates eee the air flow dida IRON S Video 23 59 127 01 Video
14. ents as required Completely tighten the hardware between the frames and pedestals before adding the next row of frames Some adjustment of the pedestal feet may be required to achieve a level row a Use a 5mm allen key and two 10mm open ended wrenches to tighten the hardware on the pedestals b Use a 13mm open ended wrench to tighten the hardware securing the frames to the pedestals c Use a 6mm ball driver to tighten the hardware securing the frames together Snap grommets into the cutouts of the frames on each end of the row These grommets ensure the cables do not rub against the metal cutout see image above 2 5 3 Adding Additional Rows of F100 Frames 2 6 1 Add the second row beginning with the center and working outward Complete these steps for each frame in the next row a Using safe and approved lifting methods install the next frame over the lower frame approaching it from the back b Once the top frame is resting on the lower frame slide it forward until it is in position Align the top and bottom frames until all edges are flush and the mounting holes are aligned ao Using 6 M8 socket head cap screws and 6 flat washers 8 4 secure the upper frame to the one below Hand tighten the hardware at this point to allow for small adjustments as the other frames are added to the row e Position the next frame in the row Using 4 M8 socket head cap screws and 4 flat washers 68 4 secure the frame to the one adja
15. he product appropriately and according to local regulations In the European Union there are separate collection systems for used electrical and electronic products Please help us to conserve the environment we live in GENERAL WARRANTY STATEMENTS For complete information about Christie s limited warranty please contact your Christie dealer In addition to the other limitations that may be specified in Christie s limited warranty the warranty does not cover a Damage occurring during shipment in either direction b Damage caused by misuse improper power source accident fire flood lightning earthquake or other natural disaster c Damage caused by improper installation alignment or by product modification if by other than a Christie authorized repair service provider d Problems caused by combination of the equipment with non Christie equipment such as distribution systems cameras video tape recorders etc or use of the equipment with any non Christie interface device e Failure due to normal wear and tear f Warranty does not cover image retention PREVENTATIVE MAINTENANCE Preventative maintenance is an important part of the continued and proper operation of your product Please see the Service Manual for specific maintenance items as they relate to your product Failure to perform maintenance as required and in accordance with the maintenance schedule specified by Christie will void the warranty CHAISTIE Table of
16. ht of panel with adapter plate and display carriage 52 kg 114 6 lbs 5 Approximate weight of frame 16 7 kg 36 8 Ibs 6 Approximate weight of pedestal 24 8 kg 54 7 lbs Pedestal P N 135 106108 NOTE Illustrations shown as third angle projection Not to scale Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 11 CHAISTIE A 3 Attaching Pedestal and Frame 116 44 13 78 417 66 to 2 91 i 73 96 AO 7 Fasten to wall 6x Max torque 9Nm 80lb in Height adjustment knob right 1600 2 71 69 Height adjustment knob left 28 37 00 General Notes 1 Views shown here are for pedestal and frame assembly for landscape orientation 2 Maximum adjustment possible using height adjustment knob is 25mm 1 3 Maximum range of adjustment on threaded foot along Y axis is 50mm 2 11 391 N 235 10x M8 22 08 23 69 560 8 Fasten frame with max torque 15Nm 133lb in when used with lubricated screws 31 4x 2800 Secure adjacent pedestal with max torque of 13Nm 115lb in when used with lubricated screws 24 61 625 0 Panel cap x2 Foot 7 09 threaded rubber x3 209 Attaching pedestal and frame with M8 screws washers and nuts 6 each per pedestal and frame assembly Attaching display carriage to frame Attaching panel with adapter plate to display carriage NOTE Illustratio
17. ns shown as third angle projection Not to scale Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 11 Corner adjustment knob left Appendix A Mechanical Drawings L Corner adjustment knob right L 115 751 400 600 4x M8 2x Adapter Plate 27 01 686 1 L 6 85 47 84 1215 3 174 General Notes 1 Maximum adjustment possible using corner adjustment knob is 19mm 0 75 2 Fasten M8 screws with a maximum torque of 1 27Nm 11 284 Ib in A 3 Corporate offices USA Cypress ph 714 236 8610 Canada Kitchener ph 519 744 8005 Worldwide offices United Kingdom ph 44 118 977 8000 France ph 33 0 141 210036 Germany ph 49 2161 664540 Eastern Europe ph 36 0 147 48 100 Middle East ph 971 0 42997575 Spain ph 34 91 633 9990 Singapore ph 65 6877 8737 Beijing ph 86 10 6561 0240 Shanghai ph 86 21 6278 7708 For the most current technical documentation please visit www christiedigital com Japan ph 81 3 3599 7481 South Korea ph 82 2 702 1601 CHRISTIE
18. ommended that the P100 Pedestals are used with both the F100 Frames and the FHD551 X LCD Panels Installers must ensure that the LCD panels are mounted to or within a secure structure that can adequately support the weight of the stacked panels If a display wall is built with any other platform the installer must ensure that the platform is stable and can support the weight of the frames and LCD panels to their stacking limits Ensure that pedestals are level before stacking the F100 Frames and LCD panels See also 1 4 3 External Support on page 1 2 External Support Stacked pedestals frames and LCD panels can tip over and cause severe injury or damage when not properly secured The display wall must be supported during and after installation to a structurally sound surface such as a permanent wall or an installer approved free standing external support structure The P100 Pedestals F100 Frames and LCD panels must be stacked onto a level surface If stacked on a non level or inclined surface there is an increased risk that the structure even when mounted in secured or free standing external structures could tip over and cause serious injury or damage It is strongly recommended that P100 Pedestals be used to create the platform for a display wall incorporating the F100 Frames and FHD551 X LCD Panels Lifting LCD Panels EN ile Lift equipment MUST be used to lift LCD panels into position on higher rows A crew of two can lift an LCD
19. panel into position on the first row Airflow Considerations It is important that the room temperature measured all around the display wall is no greater than the operating temperature which is min 5 C 41 F max 40 C 104 F It is up to the installer to determine based on their installation how much open area is required around the display wall for adequate airflow Contact Information For current contact information refer to www christiedigital com Pedestal and Frame Installation Manual 020 100734 02 Rev 1 11 2011 CHAISTIE 2 1 2 1 1 Installation and Setup Installation of a display wall for the FHD551 X LCD panels should be undertaken only by qualified installers with the requisite training knowledge and skill to properly install the system The following instructions outline how to install a display wall for the FHD551 X LCD panel as a single or multi unit system using the P100 pedestal and F100 frame Additional important information relating to the display wall can be found in the ML10 MP10 40 65 LCD Video Wall Mount Instruction Sheet P N 020 100726 xx and the LCD Panel FHD551 X User Manual P N 020 100713 xx The installer should be familiar with this information before starting the installation These instructions are intended to provide qualified installers with step by step installation information however circumstances and conditions may vary from one installation site to another and the
Download Pdf Manuals
Related Search