222400 Instructions
Contents
1. Replace the pressure regulator spring with the pressure spring that is supplied with your TCI 222400 Kit You will need to use the shim that is provided with your kit If your transmission came with a shim use the one 1 that came with your kit If your transmission had one or more shims then use only one from your transmission and the one from your TCI 222400 Kit DO NOT USE MORE THAN TWO 2 SHIMS To install the Pressure Regulator Assembly place two 2 shims on the pressure regulator valve and slip the retainer in place with the tangs facing the pressure regulator spring Slip the spring over the small end of the pressure regulator valve The spring will contact the retainer Push the entire Pressure Regulator Assembly into the transmission case Push the booster sleeve in and install the new snap ring The snap ring must set into the retaining grooves of the pump TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 REASSEMBLY STEP 6 Place the valve body gasket C Case onto the separator plate Use a small amount of petroleum jelly to hold gasket into place Reinstall check balls into check ball location in case Only five 5 will be used in valve body See Figure 4 Use petroleum jelly to hold check balls into case With the check bails in position install the separator plate and gasket against case Use a pan bolt in the center of t2. OOTING GUIDE Malfunction Probable Cause Slips Valve body bolts ioose Low fluid level Boost valve in Pressure requiator improperly instaHed Overheating insufficient coolercapacity clogged lines or cooler Foaming oil at dipstick Fiuid leveltoo high or breather Clogged lines or cooler Erratic shifting Vacuum line cracked or leaking Shifter not property adjusted Kickdown switch not properly adjusted Low fluid ievel High fluid levei Valve body bolts loose Kickdown solenoid ioose ate hard shifts Vacuum line cracked orleaking Kickdown solenoid loose ordamaged Kickdown solenoid gasket damaged Vill not shift Kickdown soienoid loose or damaged Govermortubes not property installed 1 2 Shift valve sticking Cup plug installed to deep Pump buzz or whine Low fiuid level High fiuid level Cut damaged or missing pick up tube O rings TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 Social Media Stay up to date with the latest TCI and COMP Performance Group company and product information by following us on any of our social media platforms f facebook com T ClAuto 3 twitte com TClAuto fa cpgnation com Limited Warranty TCI Automotive warrants that all of its products are free from defects in material and workmanship for a period of 1 one year from the date of purchase This limited warranty shal
3. ase This should loosen the pan enough to allow the transmission fluid to drain After the fluid has drained slowly remove the front two 2 bolts and carefully remove the pan Not all of the fluid will be out of the transmission but you should be able to remove the pan without too much of a problem Put your transmission pan bolts into the pan and set aside You may want to consider installing a TCI 805800 Universal Drain Plug Kit now that you have removed your transmission pan STEP 2 After you have removed your transmission pan you will need to remove the oil filter Two 2 types are common 1 65 67 This filter is a long box like unit which runs along the driver s side of the case This filter can be removed by grasping both ends of the filter and pull straight down Watch out for oil splatter Remove the O ring from the hole in the transmission case if it did not come out with the oil pick up tube 2 68 and Later This filter is a large flat ripple surface filter in the center of the transmission case This filter is held in place with a bolt Use a 1 2 wrench to remove this special shouldered bolt You must use this bolt when reinstalling the transmission filter After you have removed the bolt pull the filter straight down Watch out for oil splatter If the pick up tube does not come out with the filter pull the pickup tube out and remove the O ring from the hole in the case TCI Automotive 151 Industrial Dr To
4. ate the O rings supplied in your kit with transmission fluid Push the pick up tube and filter assembly into the transmission On 68 and Later models the filter is held in place with that special shouldered bolt use the same bolt and torque to 10 foot pounds STEP 12 Clean transmission pan and scrape off all gasket material Remove all gasket material from transmission case Using the pan gasket supplied with your kit install the transmission pan Torque bolts to 12 13 foot pounds STEP 13 Check shifter adjustment Place shifter in neutral Loosen pinch bolt on shifter rod cable Align selector lever on shifter to neutral and tighten pinch bolt Shift transmission in all gear ranges Make sure detents in transmission correspond exactly with shifter selector lever position STEP 14 Add four 4 quarts of automatic transmission fluid for stock depth pans With the rear wheels off the ground start engine and shift the transmission through all gear ranges Place the transmission in neutral and check fluid level It should be between the Full and Add marks on your dip stick DO NOT OVERFILL This can cause a foaming action that could cause the transmission to not operate properly STEP 15 Lower vehicle and drive for 1 2 miles to warm up transmission Recheck fluid levels If necessary add fluid Safe level is between the Full and Add marks You should be able to feel the harder positive shifts of the TCI 222400 Kit TROUBLE SH
5. enoid Gasket Aluminum One 1 Pressure Regulator Spring One 1 Pressure Regulator Spring Shim Two 2 Oil Pick Up O Rings One 1 Booster Valve Snap Ring Tools Required for Installation Speed Handle or Ratchet 3 8 Drive 1 2 Socket 3 8 Drive 7 16 Socket 3 8 Drive Small Blade Screwdriver Torque Wrench Snap Ring Pliers Needle Tip TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 DISASSEMBLY Automatic transmissions operate at temperatures between 150 F and 250 F It is suggested that the vehicle be allow to cool for a few hours before disassembly to avoid burns from hot oil and parts The vehicle should be off the ground 1 2 feet so you will have plenty of room to work MAKE SURE THE VEHICLE IS FIRMLY SUPPORTED Jack stands in good condition wheel ramps or a hoist will work fine Make sure the jack stands will support the weight of the vehicle You will need a box or pan to put small parts into so they will not be lost You will need a drain pan to catch the transmission fluid when the transmission pan 1s removed STEP 1 Turbo 400 transmissions do not have drain plugs You will need to remove the back transmission pan bolts first and work toward the front until you have two 2 bolts left in place If the transmission pan has not dropped down insert a screwdriver between the transmission pan and transmission c
6. he plate to hold in position for now Check Ball gt La av ae eS ee eu STEP 7 Install detent solenoid in position using the new aluminum gasket supplied with kit only if detent solenoid does not have a rubber seal Install your 4 x20 bolts finger tight Now remove the pan bolt that held the separator plate and gasket in position STEP 8 Install the valve body onto the transmission Guide the governor tubes back into the holes at the rear of the transmission Push up on the valve body governor tubes and engage the manual valve with the shifter linkage Hold the valve body in place using one 1 valve body bolt Now line up the valve body and install the rest of the valve body bolts finger tight STEP 9 Check the detent spring to see that it is in position and rides on the manual linkage Tighten valve body bolts and detent solenoid to 8 10 foot pounds of torque Route the white smog wire and connect the switch on valve body Run selector lever through all gear positions to check the operation of the manual valve and shifter STEP 10 Replace your filter We recommend a new TCI 228500 if your transmission has a flat type filter Any transmission with over 20 000 miles needs a new filter TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 STEP 11 Install the two 2 O rings on your pick up tube Before installation lubric
7. l cover the original purchaser TCI Automotive s obligation under this warranty is limited to the repair or replacement of its product To make a warranty claim the part must be returned within 1 one year of purchase to the address listed below freight prepaid Items covered under warranty will be returned to you freight collect It is the responsibility of the installer to ensure that all of the components are correct before installation We assume no liability for any errors made in tolerances component selection or installation There is absolutely no warranty on the following eAny parts used in racing applications eAny product that has been physically altered improperly installed or maintained eAny product used in improper applications abused or not used in conjunction with the proper parts Damage due to excessive manifold pressure e g nitrous backfires engine misfire etc There are no implied warranties of merchantability or fitness for a particular purpose There are no warranties which extend beyond the description of the face hereof TCI Automotive will not be responsible for incidental and consequential damages property damage or personal injury damages to the extent permitted by law Where required by law implied warranties or merchantability and fitness are limited to a term of year from the date of original purchase This warranty gives you specific legal rights and you may also have other legal rights which va
8. ld the detent solenoid in place Next remove the detent solenoid this will have to hang by its wire See Figure 1 Remove the separator plate and gasket by pulling separator plate straight down There are six 6 4 steel check balls that are held in place with the separator plate Be careful not to lose any of these check balls They must be reinstalled into place Put these check balls in your parts box Scrape all gasket material from the transmission case Keep the gasket material out of the transmission These flakes can cause the transmission to work improperly Remember to keep everything clean TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 20 STEP 5 Locate the pressure regulator snap ring in the transmission case near the selector lever linkage See Figure 2 Push up on the aluminum sleeve and remove the snap ring The unit is under spring tension After you have removed the snap ring be careful to not let the booster sleeve assembly fly apart If the assembly does not easily drop out you may need to tap the face of the sleeve Observe the order in which the booster sleeve assembly comes out of the transmission Snap Ring Booster Sleeve Booster Valve Pressure Regulator Spring Spring Retainer Shim may be more than one or no shim at all it depends on the model of the transmission and Pressure Regulator Valve See Figure 3
9. ll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15 STEP 3 Observe the location of the manual linkage shifter and detent spring with roller See how the linkage engages the manual valve in the valve body Note the location of the governor tubes and their routing observe the detent solenoid oval can and wire connector white smog switch wire 71 and later only and the routing of the wire See Figure 1 Now remove all the valve body bolts except one 1 Three O 3 are 1 4 x20 and the rest are 5 16 x18 If you have a 71 or later model Turbo 400 transmission you will need to disconnect the white smog switch wire from the valve body Let it hang free Hold the valve body in place and remove the last bolt from the valve body The valve body may spring down slightly To remove the valve body pull down on the valve body and governor tubes at the same time DO NOT let the manual valve fall out this can cause damage See Figure 1 Place the valve body in the transmission pan or in a clean box until you are ready to modify the valve body NOTE The front servo may fall out on some 71 and later transmissions when you remove the valve body DO NOT PANIC The servo can easily be replaced Reassemble in this order Spring Retainer Shaft with U Clip and piston with flat face out See Figure 5 Use grease to hold the servo in place STEP 4 Remove the two 2 bolts that ho
10. ry from state to State CALIFORNIA PROPOSITION 65 WARNING This product may contain one or more substances or chemicals known to the state of California to cause cancer birth defects or other reproductive harm TCI Automotive 151 Industrial Dr Toll Free 1 888 776 9824 Ashland MS 38603 Part TCI 9070 www tciauto com Phone 662 224 8972 Revised 4 14 15
11. y a A S o AUTOMOTIVE TH400 STREETFIGHTER SERIES VALVE BODY 1965 87 MANUAL AUTO VALVE BODY INSTALLATION INSTRUCTIONS TCI 222400 TCI 222400 ALLOWS AUTOMATIC SHIFT FEATURES IN THE DRIVE POSITION Thank you for choosing TCI products we are proud to be your manufacturer of choice Please read this instruction sheet carefully before beginning installation and also take a moment to review the included limited warranty information Contact us toll free at 1 888 776 9824 or at www tciauto com under Tech Support with any questions Please read all the instructions before you begin You may want to refer to a Motor Service Manual or any good How To Manual if you are not completely familiar with reworking a transmission Work slowly and do not force any parts Transmissions components are precision fit parts and care must be taken to install properly Burrs and dirt are the number one enemies of an automatic transmission Cleanliness is very important so a clean work area is a must Use a large piece of cardboard to cover work bench tops if they cannot be cleaned adequately NOTE The TCI 222400 will not work in a transmission in poor condition DO NOT install in a transmission that is slipping or not operating correctly This TCI 222400 Kit Contains OTY Description One 1 Valve Body Gasket VB Valve Body Side One 1 Valve Body Gasket C Transmission Case Side One 1 Separator Plate One 1 Pan Gasket One 1 Detent Sol
Download Pdf Manuals
Related Search