Three Dollar TK-Mech - Sho-Rack
Contents
1. amp SEE LUBRICATION AND OILING INSTRUCTIONS FOR MORE INFO DOOR HOOK ADJUSTMENTS Coins May Not Total Properly or May Not Fall Through Mech Door May Not Open or May Open Without Money NOTICE LUBRICATION POINTS A amp SEE LUBRICATION AND OILING INSTRUCTIONS ON BACK COVER WHEN THE MECH IS IN A RACK the space between the Price Setter Index Pawl TK3 04 and the Latch Release TK3 05 should be about 3 16 to 7 32 as shown in Figure 1 If the Latch Release TK3 05 causes the Price Setter Index Pawl TK3 04 to rest against the Price Setter Wheel T316 as in Figure2 coins may not fall through the Mech or they may not total properly This may also cause your Rack Door not to open The Door Hook T 847 being adjusted TOO HIGH can cause this Loosen the nuts on the Door Hook and move it down till the 05 moves away from the TK3 04 about3 16 to 7 32 space If the Door Hook T 847 is LOWERED too much and the space between the TK3 05 TK3 04 is wider than 7 32 the Rack Door will open without money For Door Hook T 847 Adjustments see Figure 3 DOOR ADJUSTMENTS Coins May Not Fall Through or Total Properly Door May Not Open or Will Not Close Properly FIG 1 FIG 2 Check the Rack Door Fitting against the body of the Rack If it is the left side of the Door not closing properly or evenly against the Rack place a large screwdriv2. NUT BOLT WASHER CLIP amp TWO KEYS SPECIFY NO COIN RETURN DOOR COIN RECEIVER DOOR RECEIVER DOOR LINK COIN RETURN BAR ROLLER REJECT CAM GUIDE PLATE SPACER QUICK CHANGE PIVOT CAM PIN RACHET PAWL PRICE SETTER WHEEL MINLON 22C4 2 PER MECH PRICE SETTER INDEX HUB MINLON 22C4 INDEX WHEEL SPRING 1A BETWEEN TK3 10 TO TK3 11 CHASSIS 5115 31 WALDES TRUARC RETAINER RING TOP COVER PLATE TK TOP TK CHASSIS PRICE ILLUS PRICE CODENO PARTNO DESCRIPTION CODE NO 4950 T 310 TORSION SPRING BETWEEN 4959 PART TK3 03 TK3 04 4951 T 308 EXTENSION SPRING BETWEEN 4960 TK3 04 PRICE SETTER INDEX 4952 AWL AND TK3 11 CHASSIS 4953 TK3 12 TK3 02 EXTENSION SPRING 4961 TK3 13 QUICK SET ARM CAM LINKAGE 4972 5005 T 80 ROLLER 5015 5006 TK3 17 PRICE RANGE WHEEL 4973 5007 COVER ASSEMBLY T 819 824 EXTENSION SPRING 5037 TK3 05 LATCH RELEASE 4962 T 821 CUSHION ARM 5039 5009 2 819 5 5040 ii T 845 QUARTER CRADLE 5041 T 800 TK3 05 TK3 11 TO TK3 05 EXTENSION 4963 5012 SPRING STYLE B 5013 T 820 T 821 TORSION SPRING 5043 5014 T 846 NICKEL CRADLE 5044 T 826 ANTI CHEAT STOP 5045 5015 T 830 CUSHION ARM LINK 5046 5016 T 825 LATCH 5047 5017 T 82 ROLLER 5006 5018 T 854 CYLINDER LOCK RETAINER 5048 CLIP TK3 14 LOCK EXTENSION NATIONAL 4964 ne T 822 TOTALIZER ARM 5050 T 803 COIN GUIDE PLATE 5051 52 INDEX PAWL STUD 5052 212 T 51 COUNTER WEIGHT 5053
3. Page 7 The 7 32 SPACE ADJUSTMENT being out of alignment will cause the same problem as the Door Hook T 847 not being adjusted properly MAKE SURE DOOR HOOK AND DOOR ARE IN PROPER ALIGNMENT BEFORE ADJUSTING THE 7 32 SPACE WHEN THE RACK DOOR IS OPEN there should be 1 16 SPACE between the Latch Release TK3 05 and the Price Setter Index Pawl TK3 04 Use a Tail Bender TOOL B 6025 on the Latch Release TK3 05 Tab where the Rocker Arm T 835 Tab connects onto it This allows your Wheel to reset See Illustration above on the left making sure to hook TOOL B on Shaded Area representing the 05 Tab and bending slightly up or down to achieve the 1 16 Space Adjustment TRIPLE QUICK CHANGE OPTION Three Tier Pricing FIG 1 THREE DOLLAR TK MECH TRIPLE QUICK CHANGE PRICE RANGE 00 3 00 T 316 Price 1 Daily Outside edge of RED line _ Price 2 S on each wheel marks TK3 10 Price 3 SP prica N NOTICE LUBRICATION The first black line is K ITS A SEE OILING 0 value Each click is N INSTRUCTIONS On BAG 5 value Black lines 1 519 EDNER I indicate increase of 25 sen 1103 50 Value 25 6046 KX 25 Value 0 Value 7 END 4 amp We KASPAR WIRE WORKS SHINER TX 77984 DEEP END FIG 5 REMOVE A CORE 5A s 12 00 FIG FIG 4 OLD STYLE CHICAGO NATIONAL POSTION OF POSTION OF BARREL
4. Winterlube Oil should be used APPLY OIL TO MECH BY PUTTING OIL ON ARTIST BRUSH AND APPLY BRUSH TO AREA DESIGNATED TO RECEIVE OIL ONLY DO NOT SPRAY MECH WITH AEROSOL LUBRICANT DO NOT USE WD 40 Some areas of the 3 00 TK Mech should receive Light Applications of Lubriplate 105 and Door Ease or equivalent The following legend denotes areas where each of the above are to be applied Look for these letter symbols on 3 00 TK Mech Illustrations LUBRICATION POINTS AMSOIL 100 SYNTHETIC 5W 30 MOTOR OIL WINTERLUBE OIL SHOWN BY A LUBRIPLATE 105 WHITE GREASE SHOWN BY B DOOR EASE STAINLESS STICK LUBRICANT SHOWN BY C
5. be pulled completely away from the Price Setter Wheels T 316 This can be done by loosening the two nuts and bolts that hold it to the TK BACK TK3 12 and pulling the TK3 17 all the way up from the Wheels The TK3 17 binding on the Price Setter Wheels would cause them not to turn and the money would not fall through the Mech See TK3 17 on Page 13 Illustration 58 For a Triple Quick Change Mech the Barrel for the locks will need to be replaced if using a CHICAGO LOCK 2567 2200 etc or OLD STYLE NATIONAL LOCK C 2 B C 4 B etc Figure 3A shows the position of the CHICAGO LOCK Barrel in the Mech while Figure 3B shows the Lock Position The Lock Number is in to 6 00 Position on Daily as shown on Sunday the number is at the 9 00 Position and on the Special Price the number will be at 12 00 Figure 4A shows the position of the OLD STYLE NATIONAL LOCK Barrel in a Mech while Figure 4B shows the Daily Lock Position When pulling the key out on the Daily Position the flat side of the key is at the 9 00 Position Sunday is at 12 00 the Special Price is at 3 00 If using the REMOVE A CORE LOCK C 2BR C 4BR etc then you must replace the 90 Degree Stop Washer for two tier pricing on the lock for three tier pricing The Barrel DOES NOT need to be changed Figure 5A shows the view of the Barrel from the outside of the Mech while Figure 5C shows an inside view of the Barrel The Shaded Area represents the proper position of the 180 Degree Stop
6. on Page 3 The adjustment can be made from the inside of the Mech as illustrated above Take a plier and grab to the far right on the Quick Set Rocker Arm TK3 02 and bend SLIGHTLY UP OR DOWN to center the Price Setter Index Pawl TK3 04 on the Sunday Price3 Setter Wheel 2 Follow the arrows in the Illustration above Make sure to turn the Quick Change Lock back and forth from Daily to Sunday to make sure the Price Setter Index Pawl TK3 04 hits center on both Daily 1 and Sunday 2 Price Setter Wheels as illustrated in Figure 2 on Page 3 NOTE SOME PARTS HAVE BEEN REMOVED FOR BETTER VISIBILITY AND MUST BE INSTALLED FOR THE MECH TO WORK PROPERLY NOTICE LUBRICATION POINTS amp SEE LUBRICATION AND OILING INSTRUCTIONS FOR MORE INFO WHEEL AND TOTALIZER ARM SETTINGS Mech May Not Total Properly Coins May Not Fall Through Properly or Wheel Will Not Reset FIG 2 INCORRECT walk ah 5 10 FIG VAY NOTICE LUBRICATION POINTS A tT amp B SEE LUBRICATION AND OILING T836 INSTRUCTIONS ON BACK COVER Figure 1 above shows the Shaded Area of the Ratchet Pawl T 818 falling SNUG in NOTCH 60 of the Index Wheel Ratchet Assembly TK3 10 The Index Wheel Ratchet Assembly TK3 10 and the Price Setter Index Hub T 317 are aligned at the Factory when your Mech is ordered The Index Pawl T 823 should rest HALF WAY between two teeth or 7 1 notches below t
7. 3 4275 10 32 X 1 2 CARRIAGE BOLT amp 5085 KEP NUT FOR 1 847 PER UNIT THREE DOLLAR TK MECH PARTS FOR QUARTERS ONLY 822 1 98 0 801 1 99 Q 802 1 100 Q T 860 1 101 Q TOTALIZER ARM 5086 BASE SWING PLATE 5087 SWING PLATE 5088 TOTALIZER ARM STOP 5089 ABOVE PARTS ARE NEEDED FOR SPECIAL QUARTERS ONLY TK MECHS NOTE PRICE RANGE 25 7 50 THREE DOLLAR TK MECH TRIPLE QUICK CHANGE PARTS ILLUS PART NO NO DESCRIPTION PRICE CODE NO 1104 114 T 703 T 316 116 MEDIUM COMPRESSION SPRING TRIPLE QUICK CHANGE NLY 4970 TRIPLE QUICK CHANGE BARREL WITH 12 0 CLOCK STOP REMOVED SPECIFY NATIONAL OR CHICAGO 5093 EXTRA PRICE SETTER WHEEL 4971 FOR WHEEL WEEKDAY OR SPECIAL PRICING NOT SHOWN OR ILLUSTRATED WSINVHO3N 1 dVT1OGQ CLEANING AND GENERAL CARE METHODS OF WASHING It is essential to have a routine cleaning program to keep your Mechs in top working condition Dirt over oiling and soda pop can cause many of the problems with the Mechs not totalizing properly Listed below are some different methods for cleaning your Mechs use the method that you prefer Your best cleaning can be done inexpensively by soaking your Mechs in hot sudsy water up to 30 minutes with occasional movement of the Mech through the solution Dawn Dishwashing Liquid is good to use since it cuts through grease an
8. AILY TO SUNDAY CHANGE OVER Mech Will Not Change Over to Sunday Door Opens Without Money or Will Not Open FIG 1 FIG 2 an TK3 04 T 316 FIG TK3 04 T 316 Figure 1 illustrates an overall view of the Price Setter Wheels and the PRICE SETTER INDEX PAWL 04 Some parts have been removed from the Illustrations for better visibility The Price Setter Index Pawl TK3 04 should hit each Price Setter Wheel T 316 in the center to allow it to go into the Wheel and allow your door to open The SOLID LINE of the Price Setter Index Pawl TK3 04 above in Figure 2 illustrates the proper position of that part for the Daily Setting on Wheel 1 After turning your Quick Change Lock from Daily to Sunday the DOTTED LINE of the TK3 04 above in Figure 2 shows the correct position as it will go into the Sunday Price Setter Wheel 2 Figure 3 shows the Price Setter Index Pawl 04 bypassing the Sunday Wheel 2 this will cause your Rack Door to continuously open NOTICE LUBRICATION POINT A SEE OILING INSTRUCTION FOR MORE INFO ADJUSTING PRICE SETTER INDEX PAWL WITH PRICE SETTER WHEELS Mech Will Not Change Over to Sunday Door Opens Without Money or Will Not Open TK2 02 TK3 04 20 On Ai 599 adjust the Price Setter Index Pawl 04 if it is bypassing the Sunday Price Setter Wheel 2 T 316 or if it is not hitting the center of that Wheel see Figure 2 or 3
9. E TO ALWAYS ALIGN THE DOOR HOOK AND DOOR FIRST BEFORE MAKING ADJUSTMENTS TO THE MECH MOST OF THE TIME THIS WILL TAKE CARE OF DOOR OPENING PROBLEMS AS WELL AS COINS NOT TOTALIZING ADJUSTING LATCH RELEASE Door and Door Hook are Set Correctly but Door Keeps Opening or Does Not Open Coins Will Not Fall Through or Total Properly or Wheel Will Not Reset MAKE SURE MECH IS IN RACK WITH CUTAWAY HOUSING OR DEMONSTRATOR TO MAKE THIS ADJUSTMENT NOTICE LUBRICATION POINTS A amp SEE LUBRICATION AND OILING INSTRUCTIONS ON BACK COVER If your Door Hook T 847 and Rack Door in proper alignment and your Rack Door keeps opening or will not open you will not open you will need to adjust the 7 32 SPACE between the Latch Release TK3 05 and Price Setter Index Pawl TK3 04 For proper setting see Figure 1 Page 7 To adjust this look at the Illustration above on the right using Tool 6049 bend the Latch Release TK3 05 Tab to the left or right making sure not to bend the Tab too far in either direction The space being wider than 7 32 will cause the Rack Door to open without putting in money Less than 3 16 the Rack Door will not open or the Latch Release TK3 05 may cause the Price Setter Index Pawl TK3 04 to touch the Price Setter Wheels T 316 and this would cause your coins not to fall through the Mech or not to total properly See Figure 2 on
10. IN MECH LOCK IN MECH 5 INSIDE VIEW BARREL POSTION OF POSTION OF BARREL IN MECH LOCK IN MECH 6 00 POSITION 180 DEGREE STOP WASHER Triple Quick Change offers you a Daily Price Wheel 1 Sunday Price Wheel 2 and a Special Price Wheel 3 as shown in Figure 1 To change your 3 00 TK Mech to a Triple Quick Change you will need to cut the Retainer Ring T 319 which holds your Price Setter Wheels T 316 and Compression Springs in place with cutting pliers Remove the Retainer Ring T 319 along with the 1102 Large Compression Spring from the Price Setter Index Hub T 317 Leave the other two Price Setter Wheels T 316 on the Hub Add a 1103 Small Compression Spring and another Price Setter Wheel T 316 on top of them Then place a 1104 Medium Compression Spring on top Replacing the 1102 Large Spring Put a new Retainer Ring T 319 on top using the shallow end of a 3 00 Wheel Retainer Ring Applicator 6046 TOOL C to push the Retainer Ring on the Price Setter Index Hub T 317 See Illustration on Figure 2 Parts are shown disassembled for better visibility If using the Deeper cut end of the Retainer Ring Applicator the Price Setter Wheels would not be able to be pulled apart to change prices The Deep end is used on two tier Price Wheels After putting Retainer Ring on make sure the Wheels can be pulled apart to change your prices The Price Range Wheel Cover Assembly TK3 17 needs to
11. THREE DOLLAR TK MECH MECHANISM SERVICE MANUAL JULY 1 1997 FOR ASSISTANCE AND PARTS CALL OR 1127 SHINER TX 77984 361 594 2911 800 527 1134 FAX 361 594 4264 http www shorack com SETTING PRICE SETTER WHEELS Door Opens For Less Money Without Money or Will Not Open TO CHANGE ll 5 PRICE TURN S 125 VALUE COUNTER CLOCKWISE 7 10 VALUE ij aig 75 VALUE Pn ef RY Zs gz x 50 VALUE j X I 25 VALUE PRET W Qy V t 0 VALUE i S lt k 2 ZA So 12 CHANGE your prices the 3 00 Wheel turn the Wheels Counter Clockwise as shown above Price Setter Wheel 1 T 316 is the Daily Price and should always be set first before setting the Sunday Price Wheel 2 T 316 The Price Range on the 3 00 Wheel is 0 to 3 00 The OUTSIDE EDGE OF RED LINE on the Wheel represents your price setting The First Black Line is 0 Value and each click is a 05 Value Black Lines indicate an increase of 25 Price Setter Wheel 1 T 316 shows a price of 25 above Price Setter Wheel 2 T 316 is the Sunday Price and should be adjusted in the same way as the Daily Price Setter Wheel Make sure to pull Wheel 2 out from Wheel 1 and turn Counter Clockwise to your desired Sunday setting as shown above NOTE IF MOVING WHEEL 1 DAILY PRICE WHILE ADJUSTING WHEEL 2 SUNDAY PRICE YOUR DAILY SETTING WILL BE CHANGED D
12. Washer needed for Triple Quick Change Figure 5B shows the REMOVE A CORE LOCK in the Barrel on the Daily Position When pulling the key out on Daily the flat side of the key faces the 9 00 Position Sunday is at 12 00 and the Special Price is at 3 00 Set the Price Setter Wheels T 316_ and the Price Setter Index Pawl TK3 04 the same as illustrated before The following Pages show the procedures to follow Pages 2 3 4 and 6 Parts needed for Triple Quick Change Conversion are shown on the Parts List ILLUS PART NO NO TK3 02 21 TK3 03 22 TK3 04 23 TK3 10 24 T 839 25 T 82 26 T 838 27 T 836 28 T 82 29 T 835 30 T 837 31 T 800 T 835 32 T 835 T 840 33 T 841 34 T 840 35 T 80 36 T 800 T 842 37 T 842 38 T 853 39 T 808 40 T 809 41 T 81 42 T 824 43 T 82 44 T 827 45 T 43 46 T 313 47 T 818 48 T 316 49 T 317 50 T 318 51 T 319 52 T 811 89 T 810 90 TK3 11 THREE DOLLAR MECHANISM DESCRIPTION QUICK SET ROCKER ARM CARRIAGE FOR PRICE SETTER INDEX PAWL PRICE SETTER INDEX PAWL INDEX WHEEL RACHET ASSEMBLY RELEASE ARM ACTUATOR ROLLER ROCKER ARM CONNECTOR LINK ROCKER ARM RESET LINK ROLLER ROCKER ARM ACTUATOR EXTENSION SPRING EXTENSION SPRING ROCKER ARM LINK RECEPTACLE 2 9 E RINGS ROLLER EXTENSION SPRING COIN RETURN DOOR ARM CYLINDER LOCK CIAN NATIONAL OR CHICAGO
13. d grime Soaking time will vary depending on the amount of dirt and grime built up After washing rinse your Mechs thoroughly with clean water and them it is best to blow dry them If putting Mechs in a dishwasher remove the Side Cover Plate T812 and the Top Cover Plate 7811 and run through a full cycle If using an all purpose degreaser spray wash your Mechs in hot water rinse in hot water and blow dry If using Century SS Safety Solvent Spray on the Mechs blow off or wipe of excess dirt Whichever method is used for cleaning the Mechs make sure after the Mechs are dry to reoil all the studs that have working parts on them including studs that have rollers attached The Totalizer Arm T822 and the Wheel TK3 10 studs are very important parts to be oiled after cleaning NOTICE LUBRICATION AND OILING INSTRUCTIONS BELOW After cleaning and oiling if the Totalizer Arm T822 is still sluggish you may have to use a 125 Drill Bit and ream the bushing out Any defective parts should be replaced at this time and all minor adjustments made Usually a clean 3 00 TK Mech will solve most of the problems when it is not totaling properly LUBRICATION AND OILING INSTRUCTIONS DO NOT OIL MECH The notation above applies to 3 00 TK Mechs Most of the problems of a Mech not totaling properly are due to too much oil which attracts dirt and causes money not to fall through or Mech will Mistotal Amsoil 100 Synthetic 5W 30 Motor Oil
14. er handle between the right upper side of the Door and Rack then push on the left upper side of Door with hand Check to see if the Door is closing all the way against the Rack Repeat on whichever side is needed See Figure 1 above If the Rack Door does not come into the Rack centered and is binding the Door can be moved from side to side with a big screwdriver Also check for the Door Latch Bracket fitting properly against the Housing front as shown by the Solid Line in Figure 2 The Dotted Line in Figure 2 shows the Door Latch Bracket fitting too far away from the Rack Open Rack Door and hit inward with a rubber mallet or bend inward with a big screwdriver to make it fit properly against the Housing front as shown by the Solid Line Any of these adjustment being out of alignment can cause the Latch Release TK3 05 to push the Price Setter Index Pawl TK3 04 up against the Price Setter Wheels T 316 as illustrated on Page 7 Figure 2 causing your coins not to fall through the Mech or not to total properly This may also keep your Rack Door from opening Throwing a stack of papers on the Rack Door as well as Door Jerking and Door Slamming from Vandalism can cause the Door Hook and Door to get out of alignment The Door Springs being too weak can also keep the Rack Door from closing all the way Also make sure the Door Pull has not pushed in the Housing If Mech and TK Housing are bent they will need to be straightened out NOTE MAKE SUR
15. he Ratchet Pawl T 818 as in Figure 1 and should also hit center against the 10 as illustrated above in Figure 2 These adjustments being out of alignment may cause your 3 00 TK Mech not to total properly or coins may not fall through the Mech properly Figure 1 shows the position of T 818 and T 823 when the Mech is in a Sho Rack Each tooth on the Index Wheel Ratchet Assembly 10 represents 1 Nickel As Nickels are inserted the Index Wheel will move two 2 notches for each Dime inserted Example Price is set on 25 The T 818 will move from notch 60 to notch 55 in order for the Rack Door to open When the Rack Door is open the Ratchet Pawl T 818 should lift away from the Index Wheel Ratchet Assembly TK3 10 allowing the Wheel to reset as shown by the Dotted Line in Figure 1 above The Rocker Arm Reset Link T 836 controls this NOTE SOME PARTS HAVE BEEN REMOVED FROM THE ILLUSTRATIONS FOR BETTER VISIBILITY AND MUST BE INSTALLED FOR THE MECH TO WORK PROPERLY PRICE SETTER WHEEL ADJUSTMENTS Door May or May Not Open or May Get Paper For Less Money FIG 1 3 TK3 04 T 316 04 TAB BEND SLIGHTLY UP OR DOWN WITH PLIERS AS NEEDED THE BASE OF TAB If the door opens for a Nickel less than your price or does not open and the Price Setter Wheels T 316 are set on the CORRECT PRICES you may need to adjust the Price Setter Index Pawl TK3 04 Make sure the Mech is in a Rack with cuta
16. ta T 823 INDEX PAWL 5054 800 T 801 EXTENSION SPRING 5055 wee T 801 BASE SWING PLATE 5056 T 829 NICKEL STOP PAWL 5057 5026 T 777 DIME STOP PAWL 5058 STYLE 2 4955 T 813 COIN SLIDE 5059 4956 T 802 SWING PLATE 5060 T 82 ROLLER 5006 4957 T 79 HINGE PIN 5061 T 801 T 802 TORSION SPRING 5062 4958 T 812 SIDE COVER PLATE 5063 807 SIDE MOUNTING PLATE 5064 5065 TK3 12 TK BACK 4966 5066 T 77A INDEX PAWL GUIDE STUD 5069 4965 T 806 HOLD DOWN ASSEMBLY 5070 ILLUS PART NO NO T 847 95 T 852 96 SR 200 20 97 T 779 98 TK3 16 99 1102 112 1103 113 5133 9ZF 5133 12ZF 5133 15ZF 5133 18ZF T 855 T 856 T 857 T 857 1 T 858 T 775 T 859 THREE DOLLAR TK MECH MECHANISM PRICE DESCRIPTION CODE NO DOOR HOOK 12 GA MATL 5071 COIN RETURN ACTUATOR 5072 INCLUDES E RING COIN RETURN ACTUATOR 5073 BUSHING THEFT BAFFLE 5064 QUICK CHANGE LOCK 4967 EXTENSION CHICAGO LARGE COMPRESSION SPRING 4968 FOR PRICE RANGE WHEEL SMALL COMPRESSION SERING 4969 FOR PRICE RANGE WHEE E RING FOR 3 32 DIA SHAFT 5074 E RING FOR 1 8 DIA SHAFT 5075 RING FOR 5 32 DIA SHAFT 5076 E RING FOR 3 16 DIA SHAFT 5077 M4 X 8MM PAN HEAD MACHINE 5081 SCREW M4 X 8MM FLAT HEAD MACHINE SCREW 5082 M4 X 7 HEXNUT WITH 5083 EXTERNALTOOTH LOCKWASHER ATTACHED M4 X 7 NYLON STOPNUT 5099 M4 X 10MM PAN HEAD 5084 MACHINESCREW SHOULDER BUSHING FOR T 827 CM 100 3
17. way housing or Demonstrator to test money If the Daily Price Wheel 1 T 316 is set on 25 insert 20 into the Mech When you pull on the Rack Door theTK3 04 should hit on the red marking at the end of Wheel 1 but it should not go into the Wheel as shown on Figure 1 If it does go into the Wheel bend the TK3 04 Tab down slightly with a plier Make sure to bend at the base of the Tab ONLY as illustrated by the Arrow in Figure 2 Test again after putting in 20 by pulling on the Rack Door making sure the TK3 04 does not go into the Wheel When you have 25 in the Mech the TK3 04 should go into the U shaped opening of the Wheel and clear it If the TK3 04 does not clear the Wheel bend the Tab up slightly Recheck adjustments as described above After checking the Daily Price Setter Wheel 1 turn your Quick Change Lock to the Sunday Price and check the Sunday Price Setter Wheel 2 the same way If the Price Setter Index Pawl TK3 04 does not clear the Sunday Price Setter Wheel 2 T 316 properly on its setting adjust the 04 Tab whichever way is needed as done previously for the Daily Wheel 1 MAKE SURE to go back and recheck the Daily Setting again The Price Setter Index Pawl TK3 04 must clear both Daily and Sunday Wheels for the Rack Door to open NOTE BEFORE ADJUSTING PRICE SETTER INDEX PAWL TK3 04 MAKE SURE BOTH DAILY AND SUNDAY PRICE SETTER WHEELS T 316 ARE SET ON CORRECT PRICES NOTICE LUBRICATION POINTS
Download Pdf Manuals
Related Search