jims® 6-speed overdrive super kit and complete 6
Contents
1. NOo 8085 IS REV J JIMS 6 SPEED OVERDRIVE SUPER KIT AND COMPLETE 6 SPEED TRANS KITS PRECISION CUT GEARS All gears are standard width for performance and strength with a close ratio 1st gear 2 94 or optional stock ratio 3 25 The last four gears are the same ratio as a stock 5 speed with a 6th gear ratio of 86 1 overdrive Super Kits Precision Cut This instruction sheet covers the following SUPER KITS No s 8085 and 8085L Instruction sheets also covers the following complete trans kit No s 800066 800166 800266 8003C6 8004C6 8020 8111 and 8112 This instruction sheet is reference for a Precision Cut 6 Speed Super Kit assembly Service and disassembly is the same as assem bly but in reverse order READ ALL INSTRUCTIONS BEFORE PERFORMING WORK IF YOU DO NOT KNOW WHAT YOU ARE DOING DO NOT DO IT JIMS IS NOT RESPONSIBLE FOR THE QUALITY AND SAFETY OF YOUR WORK If you are not sure about any of the procedures in these instructions have a reputable H D repair shop perform these procedures for you WARNING Always disconnect the Battery Ground Cable at the battery to prevent injury Your work area should be well lit Wear safety glasses over your eyes and protective clothing when working around power tools and compressed air Be careful with chemicals when cleaning parts Protect your skin from solvents and use only in a well ventilated area Degreasers are flammable and are a fire hazard Just use common sense a2. 14 Install the 1st M S fork and slide the 1st gear away from the trap door and engage the dogs of the adja cent gear to allow room for the fork to slide See Fig 10 Next install the 4th C S fork which rides on the auxiliary fork shaft No 8075 See Fig 10 and 14 Install 2nd M S and 3rd C S forks and insert the pri mary fork shaft No 34088 87 through the trap door NOo 8085 IS Installing Super Kit parts in case 1 Install maindrive gear bearing JIMS No 8996 supplied in kit using JIMS tool No 35316 80 Follow instruction sheet provided with tool See your H D service manual NOTE Never install any bearings into the case by applying pressure to the inner race or you will destroy the bearing Do not remove the mainshaft protective cover on the clutch hub spline end of mainshaft It can be removed after super kit has been installed in trans case 2 Install the new retaining ring JIMS No 11067 pro vided with the bevel facing out See your H D service manual 3 Install provided main seal JIMS No 12067A with JIMS tool No 95660 85 4 Install main drive gear JIMS No 8296 provided using JIMS tool No 35316 80 and follow instruction sheet See your H D Service Manual Install counter shaft end bearing JIMS No 8977 provided Note Install countershaft bearing by applying pres sure to the LETTER side of bearing ONLY 5 Install shifter shaft seal JIMS No 12045 supplied See your H D Service Manual 6 Install shift lev
3. Install throwout bearing kit JIMS No 2226 onto end of right clutch pushrod JIMS No 8076 supplied Refer to 2000 to 2006 Twin Cam H D Service Book No oil slinger is required 2 Install and lube right clutch pushrod with throwout bearing attached then insert into end of mainshaft 3 Note On all JIMS 6 Speed Super Kits if you do not use a JIMS side cover No 2371P or No 2371CH you will need to modify your H D or aftermarket cover as shown in Fig 12 You will also need to cut the gasket to match the side cover gasket surface area These modifications allow clearance for trap CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Fetfptmame Faia fot Havley Vavidton Motorcycles 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 8 REV J 6 13 NOo 8085 IS DISASSEMBLY In general disassembly of your JIMS 6 Overdrive is the reverse of of the installation instruc tions with only one note To remove the auxiliary fork shaft No 8075 you may need a slide hammer with a 10 32 threaded tip CAUTION 6 speed gear sets must be assembled onto the proper shaft with the dogs facing the correct mating gears Gears are laser marked with their part number This step is essential for proper assembly of the transmission Improper placement of the gears will result in the malfunc
4. and retainer inside side cover Refer to H D Service Manual 5 Install No 11179 O ring on clutch cable Thread clutch cable through hole in side cover Connect clutch cable end to cable coupler Refer to H D Service Manual 6 Locate your side cover gasket JIMS No 36801 87A supplied against trap door and attach side cover Note If you are using an O E M side cover you must use the two 1 4 20 x 2 No 1291 SHCS with 2 spe cial AN washers JIMS No 1114 that are in kit or equiv alent SHCS with a 2 length The positions of these two screw holes are shown in Fig 13 Use your O E M screws or equivalent for remaining four side cover mounting screws Apply a small amount of Blue Loctite to each screw Torque screws to 7 to 9 ft lbs in a criss cross pattern Refer to your H D Service Manual See Fig 13 page 10 for screw layout SUPER KIT TOP LID amp NEUTRAL SWITCH INFORMATION JIMS No 8085L late model Super Kit Your later model case should already have the cor Neutral Switch Wiring We have included the correct connectors for the wiring conversion from early single post to late two post neutral switch wiring One of the post wire con nectors will have to be mounted as a ground wire using the eyelet connector we ve provided For No 8085L Late super kit you can install your exist ing top cover from you original transmission and con nect to your existing neutral switch wiring CLUTCH RELEASE SIDE COVER INSTALLATION 1
5. running a electronic speedometer Spout spacer 2002 to present FL models Fetfotmance Faia fot Moiorcycles 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 2 REV J a eVehicle speed sensor and mounting screw bores b Transmission top cover and shifter drum support screw bores e ransmission drain hole bore Main drive gear bearing bore e Fork shaft bore Shifter shaft bore Mainshaft 6th gear clearance check C d e Countershaft needle bearing bore f 9 Place the door gasket JIMS No 35652 79 supplied onto both dowel pins of the trans case If the mate rial of the case above the lower rear 5 16 18 screw holes is above the profile of the gasket this materi al must be removed from the case With marker mark the case above the gasket surface See Fig 1 and 2 Remove grind or file the marked case material 1 2 inward perpendicular to gasket sur face removing the unused gasket surface of the case A die grinder with a carbide bit for aluminum cutting can be used or a coarse flat file also works well Auxiliary threaded shift fork shaft clearance 6 The threaded shift fork shaft comes installed in the FIGURE NO WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS No 8085 IS 5 Speed gear set removal Refer to H D service manual for year and model of bike for disassembly and removal of 5 speed gear set m transmission cas
6. speed sensor in either location door or case you will need to use two speedo block off plate kits for the door and case NOTE JIMS ships all Super Kits with a protec tive sleeve on the end of the mainshaft splines Leave this in place until you have installed the mainshaft through the main drive gear This sleeve protects against damaging the main drive gear seal thus preventing oil leaks JIMS SPECIAL TOOLS Special tools required for installing JIMS 6 Speed Super Kit The only special tools required are tools that may also be required for any 5 speed Description 5 Speed Maindrive Gear Tool Mainshaft Bearing Race Tool Mainshaft Sprocket Locknut Wrench Big Twin Sprocket Locker 5 speed Main Bearing Remover Solvent 184 or equivalent Brass Hammer Trans Stand BT non oil pan case Complete Modular Engine amp Transmission Stand Kit Maindrive Gear Seal Protector Tool Shifter Sleeve H D No 33114 9 or 34979 00 Remover installation JIMS Part No 35316 80 34902 84 Optional parts that may be needed to install JIMS 6 Speed Super Kit Description Center clutch pushrod 11 1 8 LG JIMS Part No 37088 85 if using original H D clutch Gear Oil 85w 140 Mega Nut Speedo Block Off Plate Kit 1 used in trans case 1 used in trans door Billet Speedo Block Off Plate Kit 1 used in trans case 1 used in trans door Speedo Re Calibration Unit If trans will be
7. 1 1 4 20 2 Allens with washers 1114 provided HARDWARE NEEDED FOR FIGURE NU 13 HARDWARE USED ON ORIGINAL JIMS BILLET SIDE COVER NOT PROVIDED IN KIT HARLEY SIDE COVER Petfotmance Faia fot areg Davidsoni 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 10 No 8085 IS REV J 6 13 A Division of Thiessen Products INC 6 C S 4th rd GEAR P N 8069A 6 P N 8063 Ath GEAR P N 8064 P N 34191 79E L4 W Auxilory shift shaft No 8075 Primary Shaft No 34088 87 1st GEAR P N 8061 2nd GEAR P N 35026 79 M S 1st P N 8068A M S 2nd P N 34193 79E FIGURE NU 14 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 Fax 805 482 9224 11 REV J 6 13 NOo 8085 IS PARTS ASSEMBLY b SPEED CLOSE RATIO 86 1 OVER DRIVE PRECISION CUT SEE PAGE 14 FOR PARTS DESCRIPTION 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 12 98 ASOD dHddS 9 ATHINd55V NOo 8085 IS JMS REV J U S A 6 1 3 A Division of Thiessen Products INC C Z AJ Y I gt ATHINd55V 4000 5 Gl IV LAVHSN XINO G808 JAnIU bl 39Vd 335 amp HVJ93 1 NDI S1HVvd LAS LAAS VD 49415 555 DAWSON DRIVE CAMARILLO 93012 PHONE 805
8. 24 oz of Torco 80W 90W oil JIMS No 1230 2 Change oil at 500 miles 3 Refill case with 75W 140 Synthetic or equivalent Petfotmance Faia Pt aey Davidson 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 9 NOo 8085 IS REV J ADDITIONAL WARRANTY PROVISIONS 1 JIMS shall have no obligation in the event a JIMS part is modified by any other person or organization 2 JIMS shall have no obligation if a JIMS part becomes defective in whole or in part as a result of improper instal lation improper maintenance improper use abnormal operation or any other misuse or mistreatment of the part 3 JIMS shall not be liable for any consequential or incidental damages resulting from the failure of a JIMS part the breach of any warranties the failure to deliver delay in delivery delivery in nonconforming condition or for any other breach of contract or duty between JIMS and a customer 4 JIMS parts are designed exclusively for use in Harley Davidson Motorcycles JIMS shall have no warranty or lia bility obligation if a JIMS part is used in any other application 5 Any JIMS parts or tools that are returned and replaced become the property of JIMS and will not be returned under any circumstance Use existing Allens 1 4 20 x 2 1 4 with washers Use JIMS 1117 1 4 20 x 2 1 4 Allens Use JIMS 1121 1 4 20 x 1 3 4 Use JIMS 1261 Allens 1 4 20 x 1 1 2 Allens Use 129
9. 482 6913 Fax 805 482 9224 3 REV J 6 13 A Division of Thiessen Products INC PARTS LIST TITLE OR DESCRIPTION TRAP DOOR 6 SPEED W SPEED SENSOR BORE MAINSHAFT 6 SPEED COUNTERSHAFT COMBO 6th GEAR 6 SPEED GEAR Ist MAINSHAFT C R 6 SPD GEAR 2nd MAINSHAFT 6 SPD 6 2 3rd MS C S2nd 8292 8 1 GEAR SthMAINSHAFT 89 O 9 1 GEAR Ist COUNTERSHAFT C R SPD 82900 16 6 RETAINING RING MAINSHAFT amp COUNTERSHAFT 10607 SCREW SHCS CHROME DOOR LOWER 8075 51 6 WASHER ANPLAIN 1116 52 6 SCREW BUTTONHEAD PLAIN 8090 53 6 SPLIT DOWEL gt 609 j 60 1 TAN WIRE ASSY 8085 ONLY 72405 98TN 63 6 DOWEL PIN DRUM 8356 6 RETAINER SHFTDRUM 142 68 1 WASHER SHIFTERSHAFT 647980 69 1 RETAINER SHIFTER SHAFT O H NOo 8085 IS SSS DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 14 REV J 6 13 NOo 8085 IS A Division of Thiessen Products INC I E l E OH a GS Joma 6 PLCS LOCATION FOR INSTALLING SIDE COVER SCREWS NO 1291 PARTS LIST CHROME BILLET TRAP DOOR DOOR BEARING 3 6 WASHER E 4 6 SCREW 1 4 20 x 1 2 BUTTON HEAD THREADED SHIFT ROD SUPPORT 6 1 SET SCREW CHROME 1 2 20 MAGNETIC DRAIN PLU
10. G FXST ONLY 739A 8 2 SPLITPIN 609 9 1 PLUG 8 FLH ONLY 2389 CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Fetfotmance G fot Marley Davidsoni 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAx 805 482 9224 15
11. IS REv J Hold the gasket against the case and mark the area with Sharpie that extends past the gaskets profile Remove this material inward perpendicular to gasket surface with a coarse round file See Fig 8 CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Feifotmance Faia fot areg Davidsoni 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 3 REV J drive oear 2 Gently install the gear set trap door assembly by sliding the mainshaft through the main drive gear slowly pushing the trap door assembly inward until the door makes contact with the two dowel pins in trans case A rubber hammer is helpful to tap the trap door assembly over the dowel pins without risking damage to the aluminum or chrome of trap door Install the door mounting screws two 1 4 20 x 1 1 4 SHCS allens JIMS No 1258 supplied 3 Apply a small amount of Blue Loctite to each screw in the Top 2 1 4 screw holes and torque them to 7 9 ft Ibs Install the 4 5 16 screws JIMS No 1118 sup plied in the bottom 4 5 16 screw holes and torque them to 13 16 ft Ibs Shift fork installation For fork placement the 3 C S 2 M S 1 M S forks will ride on the primary fork shaft JIMS No 34088 87 provided See Fig 10 and 14 The 4th C S fork rides on the auxiliary shaft See Fig 10 and
12. R FILING COVER ALL BORES Using masking tape cover all door mounting holes of trans case From inside the transmission case tape over all bores as follows CAUTION SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY FUtfotmnance Taria fot 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 3 4 REV J 7 Pillow block JIMS No 8079W supplied must be snugged down square over the dowels See Fig 5 File case for a minimum clearance 010 and maximum clearance of 060 See Fig 5 and Fig 6 Check to make sure that a clearance exists between the torsion spring and case of 1 16 to 1 8 Primary Shift Shaft Boss Clearance 8 Mainshaft 6th gear clearance to case must be checked using the trap door gasket as a template No 8085 IS inside of the door See Fig 3 Note Mark the upper right hand corner of the case with a Sharpie below the gasket surface See Fig 4 File case for a minimum clearance 010 The maxi mum clearance is 060 Pillow block clearance check CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Fetfotmane Taria for 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 4 No 8085
13. e Case preparation Use your H D Service Manual and Parts Book for reference for the year and model you will be installing this kit in If you are not sure about the procedures in these instructions have a reputable H D repair shop perform these procedures for you Case shift lever sleeve application information fro 2 2 If you purchased JIMS 80851 Super Kit for the late model original 5 speed case it should have the correct shifter shaft sleeve H D No 34079 00 that s 1 785 long installed in the transmission case This will work on our upgrad ed shifter lever and drum kit If you re installing a JIMS No 8085 Super Kit in the early 5 speed case you will need to remove the shift lever sleeve H D No 33114 79 that s 1 535 long using JIMS tool No 1664 You then need to install the provided shifter shaft sleeve JIMS No 7514 H D No 34079 00 that s 1 785 long using JIMS tool No 1664 JIMS 6 speed is designed to fit in stock 5 speed H D and aftermarket 5 speed cases This applies in most situations but there are some exceptions The internal walls of cases float around occasional ly in H D and aftermarket castings This is not an indication of a quality problem This is inherent in all castings The following checks will need to be made to ensure a problem free installation Note All JIMS transmission cases are clearanced for 6 speed installations 2B 3 CAUTION BEFORE GRINDING O
14. er assembly JIMS No 8324 supplied See page 12 item 49 7 Install shifter shaft washer JIMS No 6497HW and retaining ring JIMS No 11150 supplied 8 Install shifter shaft centering pin screw JIMS No 34978 00A provided See page 13 item 45 Instructions for installing gear set into case 1 Place door gasket JIMS No 35652 79 supplied over the two dowel pins on case NOTE Apply a small amount of lube to the inside of main drive gear and install lubed tool JIMS No 2256 2 main drive gear seal protector on mainshaft if you have removed the mainshaft protective cover as shown in Fig 9 The mainshaft protective sleeve covering the clutch hub spline on mainshaft can be used as a seal pro tector as the mainshaft is installed through the main CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Fetfotmance Faia Pt areg Davidsoni SSS DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 6 REV J side of trans with the chamfered side to the inside See H D Service Manual 3 Install mainshaft bearing race No 34091 85 provid ed on mainshaft per H D Service Manual usino JIMS tool No 34902 84 4 Install trans pulley not provided and Nut JIMS No 1708 not supplied or O E M nut 5 Install center pushrod JIMS No 37088 85 not sup plied lube both ends and sl
15. ide into mainshaft 6 Install inner primary cover clutch and primary drive Refer to H D Service Manual for the year and model SHIFT DRUM amp PILLOW BLOCK INSTALLATION Install the shift drum assembly with all 4 allen screws through pillow blocks The 3 screws JIMS No 2135 supplied are 1 4 20 x1 1 4 socket head allen and 1 screw JIMS No 1297 supplied is a 1 4 20x1 1 4 button head allen There are 3 AN washers JIMS No 1215 supplied These are used on the sock et head allen screws One JIMS No 2135 button head screw with no AN washer is used on the right side pil low block in the forward position below the detent roller See Fig 11 Install allen screws into the pillow block holes and tighten down the shift drum pillow block assembly squarely Squarely means tighten down each screw one turn at a time to pull pillow blocks over the dowels and torque to 7 9 ft lbs The right side pillow block may be stubborn in making its way over the dowels Tighten down the pillow block screws in a criss cross pattern to overcome this Install your top lid with gasket supplied and torque screws per H D Service Manual specifications Top Transmission Cover and Neutral Switch For No 8085 Early super kit install No 34904 00 neutral switch provided in the top cover from you original transmission NOo 8085 IS and through all three shift forks NOTE While pushing the auxiliary fork shaft through hold onto the 4th C S gear for
16. k and make sure the fork Is positioned correctly to receive the auxiliary fork shaft Install set screw No 3784C with blue thread locker JIMS No 4501 in threaded hole to hold shaft No 8075 in place Torque to 2 4 Ft Lbs Function check With the 4 forks installed check to make sure that the forks slide freely on the shafts by moving them back and forth with your fingers If you experience any binding of the 4th C S fork you most likely need to go back and perform clearance check Slide 3 shift forks into 3 gears this is to lock the trans to keep the gears from turning for final torquing of main drive nut Instructions for installing main seal spacer and torquing mainshaft pulley nut 1 Install mainshaft quad seal JIMS No 11165 sup plied over main drive gear on left side of trans See H D Service Manual Note Spacer 33344 94 is for late pulley only pulley REF No 40250 94A 2 Install mainshaft seal spacer JIMS No 33344 94 not supplied over mainshaft bearing boss on left CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Fetfotmance Faia fot tatley Vavitdion 555 DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 7 REV J 6 13 1 08 Radius 0 080 Depth No 8085 IS door bearings 4 Assemble side cover with ball and ramp assembly cable coupler
17. nd exercise good judgement USE MOTOR OIL FOR A LUBRICANT FOR ASSEMBLY PURPOSE ONLY Any time you see this is an indication to lubricate parts Apply a small amount of oil to parts being installed in this kit CAUTION WEAR SAFETY GLASSES EXCESSIVE FORCE MAY DAMAGE PARTS SEE JIMS CATALOG FOR HUNDREDS OF TOP QUALITY PROFESSIONAL TOOLS THE LAST TOOLS YOU WILL EVER NEED TO BUY Petfotmance Faia Pt areg Davidsoni SSS DAWSON DRIVE CAMARILLO CA 93012 PHONE 805 482 6913 FAX 805 482 9224 1 REV J 6 13 NOo 8085 IS Super Kit Case Shifter Sleeve Information NOTE f you are installing No 8085 Super Kit you must use the provided H D No 34979 00 or JIMS No 7514 shifter sleeve in the case to work correctly with the upgraded 6 speed shift drum and lever assembly The length of this sleeve is 1 785 inches long If your case has the original sleeve in it from 1980 to 1999 Evo Big Twin or 1999 2000 Twin Cam FLHT or FXD you will need to remove the shorter sleeve and install the JIMS No 7514 sleeve Use JIMS tool No 1664 sleeve remover and installer tool to install the provided sleeve Speedo Information If you will be running an electronic speed sensor you will need to install a speedo block off plate See Optional Parts needed list above over your sensor hole in the case using your favorite gasket sealer and install your electronic speed sensor in the door If you will not be using an electronic
18. rrectly JIMS No 8085 early model Super Kit You will need to provide a H D top cover No 34541 00 or equivalent for H D No 33904 00A neutral switch provided We have provided the correct wiring connectors to connect to the neutral switch EXHAUST MOUNTING BRACKET MODIFICATION You may need to modify the original exhaust mount ing bracket This will vary per model and manufac turer of exhaust Mount modified exhaust bracket to the bottom 2 or 4 5 16 door mounting screws FLH OIL FILL SPOUT MODIFICATION 1 Super kits used on FLH models will need to modify the oil fill spout to fit properly on trans case You will need to provide clearance on your fill spout to clear the trap door You will need to machine file or grind to get enough clearance so you can mount spout cover to the case in normal position without the cover touching the trap door 2 On 2001 and earlier FLH models Mount modified oil fill spout to trans case along with oil fill spout gas ket JIMS No 866 provided and mounting screws Mount and torque four mounting screws per H D Service Manual 3 On 2002 to present FLH models Along with per forming steps 1 amp 2 above you need to purchase or make a spout spacer not provided in kit For a spout spacer order JIMS No 8088 You will need to plug and relocate the vent fitting on the spout cover as needed to clear your speedo sensor FILLING TRANS WITH OIL 1 Fill the final assembled gearbox with 20
19. tion of the transmission and damage Customer Support For any installation or service Questions please contact JIMS Technical Department 805 482 6913 WARRANTY PROVISIONS All JIMS parts are guaranteed to the original purchas er to be free of manufacturing defects in materials and workmanship for a period of 6 six months from the date of purchase Merchandise that fails to conform to these conditions will be repaired or replaced at JIMS option if the parts are returned to us by the purchaser within the 6 six month warran ty period or within 10 ten days thereafter In the event warranty service is required the original pur chaser must call or write JIMS immediately with the problem Some problems can be rectified by a tele phone call and need no further course of action A part suspected of being defective must not be replaced by a Dealer without prior authorization from JIMS If it is deemed necessary for JIMS to make an evaluation to determine whether the part is defective it must be packaged properly to prevent further damage and be returned prepaid to JIMS with a copy of the original invoice of purchase and a detailed letter outlining the nature of the problem how the part was used and the circumstances at the time of failure If after an evaluation has been made by JIMS and the part was found to be defective repair replacement or credit will be granted rect lid neutral switch and wiring to connect the switch co
Download Pdf Manuals
Related Search