Kawasaki Diagnostics Quick Start Guide
Contents
1.2. Kawasaki Diagnostics Quick Start Guide Quick Start Guide Kawasaki Models Serviced 1999 2003 STX 1100 Ultra 130 DI 2002 2012 STX 12F 15F 2007 2012 Ultra LX 250X 250LX 260X 260LX 300X 300LX The USB Cable which connects the SBT Diagnostic box to the PC The Main Diagnostic Cable is used to connect the SBT Diagnostic box to all 4 stroke models The 2010 Adapter is used to connect the Main Diagnostic Cable to the new style connector on the 2010 Ultra skis The Early Relay Bypass Cable is used on the 2003 2012 STX 12 F 15F skis to keep the ECU awake during the diagnostic session The Late Model Immobilizer Bypass Cable is used on 2007 Ultra models to keep the ECU awake during the diagnostic session The 2 stroke DI Main Diagnostic Cable is used to connect the SBT Diagnostic box to the 1999 2003 STX 1100 Ultrai130 Di models 2012 Short Block Technologies Kawasaki Diagnostics Quick Start Guide 8 Connect SBT Diagnostic System to the PC with the provided USB Cord B Start SBT Diagnostics 102 by going to start menu and launching SBT Diagnostics 102 Choose Kawasaki from the listed OE manufactures 8 Connect the SBT Diagnostic System to the Jet Ski Connector SBP For all 4 stroke models attach the appropriate bypass cable to keep the ECU powered up Ensure the safety lanyard tether is attached to the stop switch B For the DI and 12F 15F models turn the key switch to ON b For the Ultra
3. for the Ultra series skis or the Kawasaki DI Detected for the STX 1100 DI Skis tS 1 Late Kawasaki Once the Kawasaki ECU indication appears go to the upper left of the screen select Vehicle and then Read Vehicle 4 CANDoo Hardware Serial Number 344 Vehicle Key Report Help Read Vehicle Write Vehicle The SBT system will read the data from the ECU You are now ready to read and clear faults view operating history and activate various functions available for the particular model you are working on General FAQ s S8m SBT Scanner Tool 102 checks for updates on startup if there is an active internet connection SBP The hardware box must always be connected to the PC when you start up the program to enable the system to check for new updates SsBm f you are using wireless and get out of range it can cause the SBT Diagnostic 102 to freeze up while trying to connect to the website on startup We suggest disabling the wireless on your laptop if you are moving out of wireless range SBE Make sure you have a fully charged battery failure to do so can cause data corruption Bm When you are finished always close the program first before disconnecting the USB cable to the SBT box If you disconnect the USB cable before closing the program the program will freeze and you may need to stop the program manually via the Task Manager to exit the program 2012 Short Block Technologies
4. ce the Immobilizer Bypass cable is installed connect he two small white one pin connectors together on this cable 7 Insert a Kawasaki key either Fast or SLO into the key switch to power up the ski ensure the emergeny lanyard is attached to the stop switch any you are now ready to start the diagnostic session 1999 2003 STX 1100 DI 2 Stroke model Connecting the Diagnostic Cabel to the Jet Ski Steps to connect 1 3 Remove the seat and look for the Yellow 6 pin diagnostic connector at the rear of the engine bay just under the seat It will have a dust cap on it with a looped single wire on the end of it Remove the dust cap from the diagnostic connector attach the STX 100 Di Main Diagnostic cable to the yellow diagnostic connector on the Ski Ensure the Safety Lanyard is installed on the stop switch and turn the key to the ON position You are now ready to start the dignostic session 2012 Short Block Technologies Kawasaki Diagnostics Quick Start Guide Starting the Diagnostic Session When the SBT application is running and the ECU has been powered up you are ready to start the diagnostic session Once the ECU is powered up the SBT application should detect the Kawasaki ECU indicated by the ski icon on the lower left of the screen changing from red to green and the status should change from looking for Vehicle to Early Kawasaki for the STX 12F 15F Late Kawasaki
5. models insert a FAST or SLO key into the ignition switch Vehicle Connection 2 Remove the dust cap and plug in the SBT Kawasaki Main Diagnostic Note Before connecting to a ski please read cable into this connector the service manual for that particular model of 3 Locate the Main Relay connector Jet Ski near the battery It is a light gray 8 pin connector shown In general starting a diagnostic session disconnected includes two steps 1 Connecting the SBT Diagnostic 102 system to the Jet Ski Diagnostic connector 2 Waking up the engine ECU to enable the SBT Diagnostic 102 system to talk to the ECU In addition the 4 stroke models need an additional bypass cable attached to keep the 4 Disconnect the Main Relay ECU powered up during the diagnostic connector and connect the Early Relay session Bypass cable in line between the two halves of the Main Relay connector 2003 2012 STX 12F 15F 4 stroke Models Fasten the ring terminal of the Early Connecting the Diagnostic Cable to the Jet Ski Relay Bypass cable to the negative ground post of the Steps to connect battery 1 Locate the 4 pin Diagnostic Connector which is located in the engine compartment adjacent to the voltage regulator assembly The connector is black and has a cap on it with yellow sealed inserts connector shown with dust cap removed 5 Ensure the emergency stop tether is attached to the stop switch and attach the ignition key to the
6. switch and turn to the ON position You are now ready to start the diagnostic session v 1 0 2012 Short Block Technologies Kawasaki Diagnostics Quick Start Guide 2007 2012 Ultra 4 stroke Models LX 250 I X 260 1 X 300 1 X Connecting the Diagnostic Cable to the Jet Ski Steps to connect 1 Locate the 4 pin Diagnostic Connector which is located next to the battery in the front storage compartment The connector is black on the 2007 2009 models and white on the 2010 2012 models 2 Remove the dust cap from the connector and attach the Main Diagnostic cable to the diagnostic connector NOTE On 2007 2009 models the Main cable connects directly to the connector on the ski On 2010 models you must first attach the 2010 Adapter cable to the Main cable then connect the 2010 Adapter cable to the diagnostic connector on the ski To keep the ECU powered up for the diagnostic session you must attach the Immobilizer Bypass cable The connector for the immobilizer is located behind the ECU so you need to first remove the ECU cover panel in the front storage compartment 2012 Short Block Technologies Kawasaki Diagnostics Quick Start Guide 4 Once you move the ECU out of the way you now have access to the immobilizer connector It is a natural nylon colored 6 pin connecior 5 Disconnect this connector and connect the Late Immobilizer Bypass cable in line 6 On
Download Pdf Manuals
Related Search