Home

Service Manual

1. li Released 06 2001 1 50 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 __ Bette Ideas better Made _ RECOMMENDED PREVENTIVE MAINTENANCE Daily Remove all lint from the looper area at least twice daily Remove lint and dust from the tabletop Lubricate all pivot points with 2 3 drops of sewing machine oil Check the two oil cups located on the right hand side of the head on the ends of the front and rear shafts fill as required Weekly Check for excessive play in the needle bar levers looper shaft and center knife pivot points Adjust as reguired Monthly Check to ensure all hardware is tight and secure Visually check for damage to patch caused by scratches or burrs on the patch guides as necessary Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 51 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ARE REECE OPTIONAL ATTACHMENTS ADJUSTMENT 221 A variety of optional attachments are available to make the Speedwelt 1000 even more productive and user friendly These options include an automatic patch loader two position cycle sewing and a work eject system Automatic Patch Loader Adjustments Setting Needle Clearance When the patch load tray moves into the load position there should be 1 2 12 7 mm clearance from the point of the needle to the inside of the patch load tray To ad
2. CTR SEW INTERRUPT switch Released 06 2001 1 8 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Pit eas LEER OR ANEIMING THE KEYPAD TO SET THE SEWING PROGRAMS 138mm POCKET 1 0175 FRONT Press the SEW INTERRUPT switch Press the CTR key TESTS PRESS 1 El ji Press 2 to program PROGRAMM PRESS 2 To program sewing press 1 To program PATCH LOADER press 2 To turn PATCH LOADER on press 2 PROG POCKET PRESS 1 OPTION PRESS 2 nn HR C gt SEMIAUTOMATIC the operator starts sewing after loading and folding AUTOMATIC the foot treadle only is Ga used NEXT CHANGE ENT The NEXT key will advance to and display the next program The NEXT 138 mm POCKET LENGTH key will display the previous program The LESS 1 MORE ENT CHANGE ENT key allows changes to be made to the current program and 8mm END LENGTH advances to the next screen within the LESS T MORE ENT program J 20 ENDS STITCHING LESS 7 MORE J ENT Once in the program the LESS key will decrease the number the MORE key will increase the number The ENT key will confirm any changes made and 10 CENTER STITCHES LESS T MORE J ENT advance the program to the next screen Tm START CKNIFE LESS 7 MORE J ENT For programming instructions for options see the Options section page 10
3. TO CHANGE THE TABKNIFE CUT NO CUT Press SEW INTERRUPT switch Press KNIFE key 1 Automatic tab knife center cut 2 No cut center or tab knives 3 Tab cut w knee switch ERROR MESSAGE Indicates table is not in the Home position Press HOME TO RESET THE COUNT OF SEWN POCKETS Press SEW INTERRUPT switch Press RST Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 156 mm POCKET 2 175 FRONT Press ENT DOES TAB KNIFE NEED Press ENT CHA NGING CANCEL SEW INTERRUPT ENT BLOCKLOAD CANCEL SEW INTERUPT CENTER KNIFE OFF ENT TAB K CUT 1 NO CUT 2 CUT KNEE SWITCH 3 ERROR TABLE NOT HOME HOME Press CANCEL SEW INTERRUPT Reset Count ENT 1 11 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 Vie BLA Malle PROGRAMMING THE KEYPAD TO THREAD THE MACHINE Press the THREAD SAFETY switch Thread machine Press the THREAD SAFETY switch to return to the sewing mode FINISHED THREA DING Press THREAD SAFETY switch When a thread breaks the machine will automatically go into the SEW INTERRUPT mode THREAD BREAK Press HOME REMOVE PATCH STITCH Press Hold DLE RELOAD PATCH Release DLE ERROR CORRECTED To ENT Continue Press Pressthe THREAD SAFETY switch to return to the sewing mode RETHREAD MACHINE Press THREAD SAFETY switch
4. When the material jams JAM TURN AIR OFF Remove the material after turning the air valve OFF SEW INTERRUPT Press TURN AIR ON Press HOME Press SEW INTERRUPT Press SEW INTERRUPT to return to the sewing mode Released 06 2001 1 12 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made ADJUSTING ROCKER RODS ROCKER ROD REPLACEMENT In most cases only one of the rocker rods O will actually required replacement However replace both of the rocker rods To replace perform the following steps 1 Turn the arrow located on eccentric stud towards the rear of the machine 2 Remove needle bar eccentric stud Q rear stud a pin 0 Be careful not to lose the small key in the eccentric stud Remove the rocker rod assembly 3 Remove the four E rings from the pins located on the rocker assembly Remove the pins 6 Disassemble the broken rod by loosening locknuts removing clevis and removing locknuts Place clevis and locknuts on new rod Re install eccentric and rear studs onto head Insert rod on the head through the opening located on the left hand side of the machine Clevis on the new rod should slide over the eccentric and rear studs The length of the rod and clevis should match the distance between the two studs Repeat for the other rod 4 Install the new rods on
5. ENT BACK J NEXT T TABLE NOT AT FRONT PRESS ENT BRUSHES NOT OUT PRESS ENT THD BLOW ON OFF ENT BACK J NEXT 1 TABKNIFE IN OUT ENT BACK J NEXT T Outside U S Phone 804 559 5000 Fax 804 559 5210 2 5 SPEEDWELT 1000 AMF REECE 2 6 Better Ideas Better Made TROUBLESHOOTING J 5 7 PATCH H DOWN ENT BACK J NEXT T CLAMPS NOT DOWN PRESS ENT BRUSHES NOT IN PRESS ENT WORK EJECT BACK J SV 9 P CLAMP UP DOWN ENT BACK J NEXT T SV 10 P LOAD IN OUT ENT BACK J NEXT f TABLE NOT AT BACK PRESS ENT CLAMPS NOT DOWN PRESS ENT NEEDLE POSITION ENT BACK J NEXT T TABLE NOT AT BACK PRESS ENT CLAMPS NOT DOWN PRESS ENT BRUSHES NOT IN PRESS ENT NEEDLE POSITION INCORRECT ADJ SYNCHRO ENT NEEDLE POSITION CORRECT PRESS ENT Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Bette Ideas Better Made TROUBLESHOOTING SET EJECT TIME ENT BACK J NEXT T MORE f PRESS ENT The ENCODER COUNT is the count of pulses ENCODER COUNT m BACK J NEXT f ENCODER COUNT HOME BACK J NEXT 7 ENCODER COUNT ENT BACK J NEXT T 12390 40 12379 BACK J SA VE COUNT 1 The FIRST STITCH and LAST STITCH numbers control the stitch length Example The higher
6. Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 p ey m OPTIONAL ATTACHMENTS ADJUSTMENTS Setting the Patch Load Tray for Home Position In the Home position the patch guide tray should be set so that it is comfortable for the operator to reach To adjust 1 Loosen the button head allen screw on bumper bracket C 2 Move bumper D backward or forward as necessary 3 Re tighten the button head allen screw Bumper Bracket Rotary Actuator Air Cylinder Released 06 2001 1 54 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas Better Made _ OPTIONAL ATTACHMENTS ADJUSTMENTS Adjusting Long and Short Patch Tray Clamps These clamps hold the welt material in plate during the loading process The patch tray clamps may need to be adjusted to maintain the correct amount of holding pressure To adjust 1 Loosen screw and move the short clamp up or down as necessary 2 Re tighten screw 3 Loosen screw and move the long clamp up or down as necessary 4 Re tighten screw Patch Load Tray Patch Holder Clearance The patch holder 9 keeps the welting and backing patches in place as they are being moved into loading position For easy inserting of material patches and to prevent interference with patch folding the distance C from the patch holder and the front left edge of the tray
7. Tab knives cutting too short Replace knives if dull otherwise adjust knives positions Center cut too long Adjust center knife One stitch will be slightly exposed at each corner of the pocket welt but side stitching should be well concealed If not tensions are too loose or clamp mats are set too close together The thread should be approximately the same color as the garment material Incorrect needle being used Check needle and change if necessary Needles are not correctly adjusted to the loopers Adjust if necessary Needle tips are blunt Replace needles Needles are not straight Replace the needles Incorrect threding and or tension 1s incorrect Re thread and or adjust the thread tension Needles are not straight Replace needles Looper has not been correctly installed Re install the looper Looper 15 sharp at the point is worn Replace the looper Needle bar 15 not aligned properly Re align the needle bar The needle and looper are not adjusted properly Re adjust Incorrect clearance between the needle and needle hole slot Re adjust the clearance Thread handling components are worn or contain burrs Replace or repair those components Th fth dle is sharp Replace th dle e eye of the needle is sharp Replace the needle Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE Ideas Better Pade _ SPEEDWELT 1000 TROUBLES
8. 16 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made PATCH FOLDING Horizontal Adjustments The brush blades must close parallel to the patch guide with a clearance on each side of the patch guide equal to the thickness of welting and backing material To assure accurate performance it is essential that the correct adjustments exist between the patch folding arms slide block 9 slide bracket 9 and clevis Refer to pages 1 13 through 1 16 to ensure the proper machine settings are in place before performing the following patch folding adjustments o Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 17 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ee ECE PATCH FOLDING Adjusting the Height of the Front End Brush Blades to the Patch Guide Loosen nut and turn screw in or out in will lower the height out will raise the height as necessary Once the proper height has been obtained re tighten nut 0 Adjusting the Height of the Rear End Brush Blades to the Patch Guide To raise the height of the brush blade tighten screw and loosen screw To lower the height of the brush blade loosen screw and tighten screw NOTE The height of the rear end brush blades must be 0 79 mm 03 higher than the front end brush blades Patch Guide Arm 0 79mm 03 gr
9. Options Press CTR With Options Press ENT 5 If the machine is equipped for this option press ENT The LCD message should now read Automatic Patch Press 1 sequence Sew Press 2 6 Press 1 The LCD message should now read Patch Loader On 1 Patch Loader Off 2 7 To activate the patch loader press 1 To deactivate the patch loader press 2 and then press ENT If the On button 1s pressed the LCD message will now give you the option of selecting automatic 2 or semi automatic 1 sewing If the automatic option is selected the patch tray will load the welt and start the machine sewing automatically If the semi automatic option 15 selected the patch tray loads the welt and the operator starts the machine sewing using the knee switch 8 Press 1 for semi automatic or press 2 for automatic sewing 9 Press ENT The steps for turning the automatic patch loading option on and off are also explained in the Options Section see page 1 44 Released 06 2001 1 58 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made _ OPTIONAL ATTACHMENTS ADJUSTMENTS Setting the Tab Knives for Two Stage Sequential Sewing When setting the tab knives for two stage sewing the longest pocket length must be set first 1 To set the long pocket use the finger screw adjustment on page 1 44 2 Now use the stop with the alle cap screw to s
10. an arm located on the shaft of the pulley passes in front of the needle sensor and activates it During this time the keypad display I O TESTS Press 1 PROGRAM Press 2 E INPUT TEST Press 1 OUTPUT TEST Press 2 KNEE SWITCH SEW OFF ON OPTION NEXT 7 T THREAD DETECT 41 o gt OFF BACK J NEXT 7 THREAD DETECT 2 ON OFF BACK J NEXT 7 NEEDLE UP ON gt OFF BACK J NEXT 7 TABLE BACK ON ON BACK J NEXT 7 TABLE FRONT ON gt OFF BACK J NEXT 7 will toggle between ON and OFF If it does not a problem exists with the sensor Table Back and Table Front Manually move the table back by gripping the brush arm and sliding to the rear of the machine The keypad will display ON sliding the brush arm forward will move the table forward and the keypad will display OFF If it does not a problem exists in the switch circuitry The opposite procedure is used for Table Front The brush arm must be slit forward which will move the table to the front The keypad will display ON sliding the brush arm to the rear of the machine will move the table back and the keypad will display OFF If 1 does not a problem exists in the switch circuitry Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 AMF REECE Better Ideas Better Made _ TROUBLESHOOTING Foot switch 1 and Foot Switch 2 Step on the th
11. between 0 79 and 1 19 mm 031 and 047 Sew a test pattern on a piece of paper to show the location of the knife cuts The end of the stitching and the tab knives should be equal If they are not equal adjust by performing the following steps in most cases the front tab knife will not have to be adjusted therefore the adjustment below 15 from the rear tab knife Loosen screw and slide the rear tab knife holder towards the front or rear of the machine sliding the holder towards the front of the machine will shorten the cut sliding it to the rear will extend the cut as necessary Once the correct adjustment has been made re tighten screw 9 To sew a pocket 6 3 4 or longer remove the rear tab knife 9 from finger shoe by loosening and removing screw Loosen screw 9 and remove finger shoe Flip the finger shoe over and re install Re tighten screw Re insert the rear tab knife and re tighten screw Adjust the tab knife holder accordingly NOTE If the front tab knife does require an adjustment perform the steps above however sliding the holder towards the front of the machine will extend the cut sliding it to the rear will shorten the cut 6 3 4 or longer Tab Cut 0 79 1 19mm 031 047 The above adjustments are standard for most fabrics and materials However if the material or fabric 15 thin slippery or stretchy compensating adjustments may be needed For example if the material is of a silky nature
12. mm 2 1 16 to 7 7 16 52 to 188 mm 9 to 14 spi 1 8 to 2 8 mm 18 to 24 spi 0 9 to 1 3 mm 2 to 5 mm Single Double Offset Overlapping Scissors Type Lower Driven Microprocessor Manual Oiling Points 220 V 60 Cycle 3 Phase 380 V 50 Cycle 3 Phase 80 psi 5 516 bar 25 cmf 7 m 32 812mm 28 5 724 mm 50 1270 mm 340 Ibs 154 41 1041 mm 32 413 mm 53 1346 mm 500 lbs 267 kg SPEEDWELT 1000 ARE REECE Better Letter Made CONTROLS POWER SWITCH The power switch controls all power to the machine It is used to power up and power down the machine In the OFF position there 15 no power to any component in the SPEEDWELT 1000 MOTOR SWITCH The motor switch controls all power to the motor In the OFF position the drive motor does not have power however the machine can still have power AIR VALVE The air valve controls the air supply to the pneumatic system The system operating pressure is 80 PSI The thread pickup arms tab knives center knife clamping and patch folding are pneumatically operated ON SWITCH The ON switch turns the microprocessor power on EMERGENCY STOP SWITCH The emergency stop switch turns the microprocessor and the motor power off SEW INTERRUPT SWITCH The sew interrupt switch immediately stops the sewing operation and activates the keypad It serves as a reset button when the clamping table is in the front or rear position IF the tab
13. position has been obtained re tighten screws To replace the spring located inside the pickup arm loosen screw Turn the retaining plate carefully to ensure the spring does not pop out Remove the old spring and install the new spring While holding the spring down turn the retaining plate until it locks into position and re tighten screw 0 Thread Released 06 2001 1 40 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Better Ideas Beiter Made _ INSTALLATION AND ADJUSTMENT OF THE SYNCHRONIZER The synchronizer positions the needle bar up when the sewing 15 finished To install a synchronizer perform the following steps 1 Place the synchronizer onto shaft 9 Slide the synchronizer onto retaining bar Tighten allen screw 2 Plug synchronizer cable into the control box located under the motor 3 Attach grounding terminal to the sewing machine using screw To adjust the synchronizer perform the following steps 1 Loosen and remove screw Remove cover Loosen screw Holding the needle bar top dead center rotate disks O so their openings are in alignment with photo eye Once they are in alignment with the photoeye re tighten screw 9 re install cover and re tighten screw 2 Release the needle bar it should stay at top dead center Sew a pocket welt to ensure the needle bar is in the up position once the sewing has st
14. the number entered ENT the shorter the stitch FIRST STITCH BACK J SHORTER 1 PRESS ENT LONGER J 250 LAST STITCH BACK J ENT NEXT 7 LONGER J 250 SHORTER 1 PRESS ENT The LCD CONTRAST controls the brightness of LCD CONTRAST the screen BACK J To exit and return to the ENT PRESS CTR DARKER T PRESS ENT LIGHTER J sewing mode press CTR SEW POCKET PRESS CTR To enter the programming PROGRAM PRESS 2 feature press 2 Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 2 7 SPEEDWELT 1000 AMF REECE Better Ideas Better Made _ TROUBLESHOOTING Changing the Needle Bite Size on the SpeedWelt 1000 Remove the a needle holder b brush arms do not lose leveling wedge c patch guide d clamp foot e throat plate f trim knife bracket g tab knife holders Install in sequence the new needle holder page 1 14 and new throat plate page 1 14 Now center the throat plate to the needle and check the center knife to the knife slot page 1 26 Adjust the clamp mats to the throat plate page 1 29 Install the new patch guide page 1 15 Install the new clamp foot with the right pivot blocks then center the clamp foot over the mats Install brush blades to the brush arms then install the arms and adjust the patch guide pa
15. the patch guide The tail end of the patch guide must be sufficient radius to allow the forming of the welt to travel smoothly on to the patch guide Remove scratches When using material that 1s slippery and dificult to hold 1 e lining material small pads of adhesive backed urethane foam should be placed on the brush blades Check that the pads do not extend beyond the length of the patch guide Check the operation of the Tab Knife Switches Select INPUT TEST on the keypad and advance using the UP arrow to the TAB KNIFE UP and TAB KNIFE DOWN screens Verify that both switches are functioning Replace and inoperable switch 2 1 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 POSSIBLE PROBLEM Ends of welt not square Corners of welts open Short tabs Stitches showing on front of welt Incorrect stitching Thread breakage 2 2 ANF REECE Better Ideas Better Made TROUBLESHOOTING POSSIBLE CAUSE AND SOLUTION Tab knives are dull or unegually positioned Replace knives setting back edges flush with back surfaces of knives Rows of stitching uneven at ends Check that needles are straight and that there is no skipping of stitches when the sewing starts Replace needles Knives are bent or not properly centered Re adjust as required Tab knives cutting too far Adjust knives Clamp mats set too close causing material to clog and tear in the corners Re adjust as required
16. 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE Ideas Better Pade _ POSSIBLE PROBLEM Clamp fails to hold the work Clamp fails to respond to treadle Welting and backing patches are not properly folded Patch folding brushes fail to respond to treadle control Welting patch does not travel along patch guide properly Tab knives fail to operate Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 SPEEDWELT 1000 TROUBLESHOOTING POSSIBLE CAUSE AND SOLUTION Check the pads of the clamping mats and replace if they are worn Check the rubber soles of the clamp foot and replace if they are worn Check and re adjust the clamping pressure 1f necessary Select INPUT TEST on the keypad Advance to the FOOTSWITCH 1 and 2 program screens and verify that the switches operate Replace inoperative switches Check the patch guide and patch folding brushes adjustments Check the Brushes switch operation Select INPUT TEST on the keypad Advance to the BRUSHES screen by pressing the UP arrow and verify that the switch is functioning Replace switch if necessary Check for binding or interference in the patch guide or patch folding brushes mechanism Remove binding or interference Re check patch guide and patch folding brushes adjustment Check patch guide adjustments Check condition of patch guide There should be no nicks or scratches This would prevent the welting patch from sliding off
17. 59 5210 AMF REECE SPEEDWELT 1000 Better Ideas Better Made POSITIONING OF PATCH FOLDING BRUSHES MODELS MODELS 5 8 D W 1 100 3 4 D W 1 350 5 8 S W 1 230 5 8 D W 1 148 NOTE The above clearances may vary depending upon the thickness of the material being sewn Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 23 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 AME REECE POSITIONING OF PATCH FOLDING BRUSHES 7 MODELS MODELS 3 4 S W 1 470 7 8 D W 1 669 3 4 S W 2 100 7 8 D W 1 655 1 16 spacer for 3 4 model 3 8 space for 7 8 model NOTE The above clearances may vary depending upon the thickness ofthe material of the being sewn Released 06 2001 1 24 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 Better Ideas Better Made _ CLAMPING Adjustment should be made with no material under the clamp foot Both clamp arms must be adjusted at the same time 1 Release all clamping pressure by loosening nuts and 0 and then backing off screw Ensure the clamp foot is in the down position and turn the air pressure on Re tighten nut 2 Check to ensure that levers and level and the center pin is 1 3 4 above clamp plate If the levers are not level and or the center of the pin is not 1 3 4 above the clamp plate adjust by loosening nut Using a p
18. AMF REECE Ideas Better Made SPEEDWELT 1000 POCKET WELT MACHINE PARTS AND SERVICE MANUAL PART NUMBER 97 0032 2 000 AMF REECE SPEEDWELT 1000 _ Better Ideas Better Made _ TABLE OF CONTENTS PAGE INIKODUCHON atta esate a NON samm 1 1 SPEEDWELIT eben 1 2 SPEED WELT 1000 SPECIFICATIONS 1 3 CONTROLS ests 1 4 OPERATOR KEYPAD AND DISPLAY een 1 6 PROGRAMMING THE PAID in 1 8 ADJUSTING ROCKER 1 13 ADJUSTING NEEDLE 23255 N 1 14 IN err 1 15 PAT Gs CIES aaa aaa aka 1 16 P IGEEOETDING atlas 1 17 POSITIONING OF PATCH FOLDING 1 22 Gp Cm antes 1 25 ERIEKEIN rr pM 1 26 CENTER 1 27 t 1 30 LOOPER 1 33 S IN eem 1 37 dsl AM NY CY PI Tc CEPS ENS 1 38 DEW OLE PEEDU du boue 1 39 INSTALLATION AND ADJUSTMENT OF THE SYNCHRONIZER 1 41 PROXIMITY SENSORS WICH 1 42 CO
19. EW INTERRUPT _ V SWITCH ON SWITCH MICROPROCESSOR MOTOR SWITCHES EMERGENCY STOP SWITCH Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 5 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ARE REECE OPERATOR KEYPAD AND DISPLAY 7 The Keypad Microprocessor controls all functions of the SPEED WELT 1000 and displays the active function on the screen There are INPUT OUTPUT tests which perform diagnostic checks on component operations They isolate problems quickly and simply The tests read each selected input or output monitor its operation and displays the results on the keypad screen All power to the SPEEDWELT 1000 1s controlled by the POWER switch The microprocessor power 1s controlled by the ON switch Both of these switches must be in the ON position before the screen will illuminate displaying the currently selected program The programs are menu driven and can be easily changed see pages 1 9 and 1 10 The keypad is locked during sewing operations to prevent accidental program changes The SEW INTERRUPT switch accesses the keypad for about 30 seconds To keep it active press one of the following keys RST L KNIFE CTR or either of the two arrow keys To deactivate the keypad press any of the following keys per screen instructions ENT HOME CTR or the SEW INTERRUPT switch The key functions are as follows RST Resets the counter to zero the L
20. HOOTING TO PERFORM MACHINE DIAGNOSTICS The purpose of the input test is to determine whether the component being tested is receiving a signal The components if working correctly will cause the keypad display to toggle between ON and OFF If there is a problem with the component the keypad display will not toggle between ON and OFF Press the SEW INTERRUPT switch Press the CTR key Press 1 to perform input and or output tests Press 1 to perform input tests The NEXT key will advance and display the next screen of the test The BACK 7 key will display the previous screen of the test To test the following components perform the steps below Knee Switch Press the knee switch in and hold the keypad should display ON when the switch is released the keypad should display OFF If it does not a problem exist in the switch circuitry Thread Detect 1 and Thread Detect 2 Lift the head cover located about 3 4 of the way back micro switches are located on the right and left hand sides of the head right side micro switch tests thread detect 22 Push the micro switch in and hold the keypad should display ON When the switch 15 released the keypad should display OFF If it does not a problem exist in the switch circuitry Needle Up Lower the head cover ift the machine and rotate the belt located in the rear of the machine on the left hand side The belt is on a pulley and as the belt is being rotated
21. It will produce single and double welts with simple variations in the automatic folding system Pocket bags can be sewn in the pocket opening The Speedwelt 1000 will sew the pocket openings at 1400 S P M Automatic seam end dense stitching locks in the seams and the threads are trimmed at the ends of the seams The operable pocket opening range 1s 52 0 mm to 188 0 mm 2 1 16 to 7 7 16 inches in length and 9 52 mm to 22 22 mm 3 8 to 7 8 inches in the width of the welted pocket opening The stitch density may be adjusted to between 9 and 14 stitches per inch Optional locating lights may be purchased witch the machine The mechanical functions are performed by a system of pneumatic and solid state electronic components The air supply requirement is 80 P S I The normal electrical supply requirement is 208 220 230 380 or 440 V A C 3 phase 50 or 60 cycle Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 1 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ARE REECE Bette Made SPEEDWELT 1000 MODELS 2 PATCH GUIDE TYPE OF MODEL NO DESCRIPTION SIZE MATERIAL 32 0000 0 210 3 8 Double Welt 725 Light 32 0000 0 211 3 8 Double Welt 661 Light Medium 32 0000 0 212 3 8 Single Welt 661 Light Medium 32 0000 0 220 7 16 Double Welt 690 Heavy 32 0000 0 221 7 16 Double Welt 730 Light Medium 32 0000 0 222 7 16 Single Welt Overlap 759 Light Medium 32 0000 0 230 1 2 Double Welt 786 H
22. LT 1000 i D irm LOOPERS ADJUSTING THE TIMING OF THE LOOPERS TO THE NEEDLE BAR 1 Remove patch guide assembly see page 1 13 2 Ensure needles are straight 3 Setthe gauge squarely on the throat plate Position the needle bar at bottom dead center by lif ng the machine and rotating the knob clockwise or counterclockwise until the needle bar is at bottom dead center At this point the needle holder should rest squarely on the first step ofthe gauge To adjust loosen the clamping screw and move the needle bar up or down as necessary Once the needle holder 15 resting squarely on the first step ofthe gauge re tighten the clamping screw NOTE When making this adjustment ensure the needles are square with the throat plate at all times NEEDLE BAR GIMBAL CLAMPING SCREW NEEDLE HOLDER BOTTOM DEAR CENTER FIRST STEP THROAT PLATE NOTE LOOPERS AT MAXIMUM REARMOST POSITION 4 When the needles are at bottom dead center the loopers should be at their maximum rear most position To adjust loosen the clamping screw located on the drive shaft assembly Center the eccentric stud with as much movement forward as backward Once the eccentric stud has been centered re tighten the clamping SCICW CONNECTING ROD CLAMPING SCREW ECCENTRIC STUD LOOPER ARM DRIVE SHAFT Released 06 2001 1 34 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 __ Better Id
23. NTROL dp 1 43 OPTIONS Pete 1 44 WORK LOCATING AND DRILL HOLE LIGHTS 1 47 D cea iial 1 48 LUBRICATION RT TR NES 1 50 PREVENELV MEN TENGAN GE icis picti etr teen enirn S epica tn oh deed 1 51 OPTIONAL ATTACHMENTS ADJUSTMENTS 1 52 WIRING DIAGRAMS Released 06 2001 U S Phone 800 237 3323 Fax 800 432 4303 Outside U S Phone 804 559 5000 Fax 804 559 5290 www amfreece com ARE REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ INTRODUCTION The new Speedwelt 1000 pocket welter features operator ease and safety faster and more accurate operation and less meintenance The microprocessor keypad operation offers user friendly fingertip control All programs selected at the push of a button feature self directing step by step guides through the program sequences All systems are electrical of pneumatic no oil to leak or cintaminate Controls are solid state electronics Non adjustable limit switches and sensors eliminate misadjustments and errors The new drive train features fewer parts reduced noise less wear and a smoother more accurate operation For operator sagery there is no high voltage above the table top This twin needle stitch type 101 chainstitch machine 15 designed to make welt pocket openings various types of garments
24. OAD position currently selected front to back or back to front HOME Atstart up this key returns the clamp table to L Selects the loading position front or back KNIFE Turns the TABKNIFE and CENTERKNIFE operation on or off cut no cut CTR Accesses the Mechanics Diagnostic Programs ENT Enters into memory any changes made Released 06 2001 1 6 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE __ Better Ideas Beiter Made _ SPEEDWELT 1000 OPERATOR KEYPAD AND DISPLAY SCREEN Operator Keypad and Display Screen To enter either the Front or Back Loading Programs Press the SEW INTERRUPT switch Press L FRONT LOADING Pressthe TREADLE half way down Releasethe TREADLE Press the TREADLE all the way down Releasethe TREADLE Press the KNEE SWITCH Press the SEW INTERRUPT SWITCH BACK LOADING Press the TREADLE all the way down Release the TREADLE half way up Press the TREADLE all the way down Releasethe TREADLE Press the TREADLE half way down Release the TREADLE Press the KNIFE SWITCH Press the SEW INTERRUPT SWITCH Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 135mm N KT LOAD Clamps will go down Clamps will come up Clamps will go down and the table will go back Brushes will close To continue sewing To cancel and the brushes will op
25. T Press 1 to turn on the patch loader Press 2 to return to the sewing screen Note The patch loader can be set for either semi automatic or automatic sewing Press 1 to return to the sewing program Press 2 to access sequential programming When 1 is pressed it will blink out and then come back on Now press 2 When the program has been set the screen will return to the sewing program Note 1 will be the long pocket 2 must be the short pocket Program 1 can programmed from 52 mm ARE REECE __ Better Ideas Beiter Made _ OPTIONS PROG POCKET OPTIONS WARNING MACH WITHOUT OPTIONS CTR WITH ENT AUTO PATCH LOADER 1 SEQUENCE SEWING 2 SEMIA UTOMATIC AUTOMATIC ON OFF PATCH LOADER 1 1 2 2 SEOUENCE OFF PROG SEOUENCE ENTER POCKET NO FOR Ist POCKET 2 ENTER POCKET NO 1 ENTER POCKET NO 2 TWO POCKETS THREE POCKETS 2 3 to 123 mm Program 2 can be any size in between 1 44 Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ OPTIONS Installing the Short Travel Kit 1 Turn off power to the machine 2 Change out the parts shown in Illustration A with those included in the kit 3 Then exchange the positions of the drive link P N 32 7145 0 000 and the li
26. air of small pliers turn piston rod in or out of clevis until this levers are level and or pin is correctly centered Once the adjustments have been made re tighten nut 3 Apply clamping pressure by turning screw inward until it bottoms Continue to turn 1 2 of a turn further Re tighten nut 4 Ensure that clamp foot holds the material firmly at all points If slippage occurs under either side of the clamp foot increase pressure to that side This is done by turning screw slightly inward Be careful not to turn the screw too tight as to cause the front of the clamp foot to be raised al lt 2 22 e 2 at E 7 2 a 2 we zi ky a Prd E Ci E P Clamping Cylinder Clamp Mat Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 25 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ARE REECE Ideas Better Made _ PRICK IN Stitch density is controlled by the speed at which the clamp travels forward At the beginning and end of each sewing cycle the clamp table slows briefly to provide closer stitch density which 1s required at each of the pocket Beginning and end stitch density 15 18 to 22 stitches per inch and should consist of 5 or 6 evenly spaced stitches at the beginning and end of each welt The clamp table speeds up to provide a center stitch density of 9 to 14 stitches per inch see diagram 9 14 stitches per inch over center posit
27. crew in the gimbal and sliding the needle bar into the proper position Lock the needle bar firmly into the gimbal by re tightening the clamping screw NOTE Ensure needles are still in alignment with the throat plate see page 1 15 GIMBAL CLAMPING SCREW NEEDLE HOLDER BOTTOM DEAD CENTER FIRST STEP THROAT PLATE NOTE LOOPERS AT MAXIMUM REARMOST POSITION Released 06 2001 1 14 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made SEWING ADJUSTING THE NEEDLE TO THROAT PLATE Before starting this adjustment ensure the clamping table 15 in the back load position 1 Select OUTPUT TEST see page 2 4 from the keypad Bring the clamps down and remove patch guide 2 Lift the machine Manually operate the needle bar by rotating the knob located on the centerknife shaft clockwise Check for a slight clearance between the needles and the throat plate openings If a slight clearance does not exist loosen screws and tap the throat plate to the right or left as necessary Once clearance has been obtained re tighten screws and re install the patch guide Note Ensure the needles are straight Cutting Slot Needle Slots Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 15 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 Emu TS T PATCH GUIDES The patch guid
28. d at the bottom of the knife holder Re tighten screws Turn the air pressure ON CENTER KNIFE TO THROAT PLATE ADJUSTMENT Place the clamp table in the rear position Open the brush blades Turn the air pressure OFF Manually lift the patch guide and keep it up using a small screwdriver Manually push the knife holder up so that the center of the knife passes up through the throat plate It must pass flush with the cutting edge of the throat plate which 15 the right side of the center slot when facing the machine and not deflect more than 051 mm 002 To adjust perform the following steps Manually push the center knife up through throat plate Loosen screws 9 located on the bearing blocks Move the center knife from side to side as necessary until the knife 1s able to pass through the throat plate with no gap on the right side ofthe knife and the throat plate Re tighten screws this point the center knife should be able to cut a single strand of thread If the knife does not cut re check the adjustment and orreplace the knife Turn the air pressure ON Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 27 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 AMF REECE CENTER CUTTING ee E SETTING THE HEIGHT OF THE CENTER KNIFE Place the center knife in the cutting position at the bottom of its stroke The leading edge of the knife point should have a clearance of 0 79 mm 031 below th
29. e 15 factory set Elimination of Side Play If play exist between the patch guide arm and hinge brackets loosen only one hinge bracket This is done by loosening screws While pressing brackets together retighten screws As long as one hinge bracket remains fixed the patch guide arm will remain centralized Leveling of Patch Guide The bottom surface of the patch guide should rest flatly on the top surface of the throat plate 9 Ifan adjustment is required loosen locknut and move allen screw up or down as necessary Once adjustment has been made re tighten locknut Setting the Tension on the Patch Guide The patch guide should have a slight drag when it is manually moved up and down If adjustment is required loosen locknuts and move screws in or out in tightens the drag out loosens the drag as necessary Once a slight drag is obtained re tighten locknuts Re check patch guide for slight drag Alignment of Patch Guide and Throat Plate 1 The knife slot of the patch guide must be aligned with the center slot of the throat plate To adjust loosen screws QD and move the patch guide to the right or left as necessary Once the alignment has been obtained re tighten screws 2 If the alignment can not be obtained by performing step 1 above loosen screws D Move the patch guide arm to the right or left as necessary Re tighten screws D Repeat step 1 above Released 06 2001 1
30. e top surface of the throat plate To adjust perform the following steps Place the clamp table to the rear position Turn the air pressure OFF Manually push the center knife holder up into the cutting position Rotate the knob 9 located on the knife shaft until the center knife is at the bottom of its stroke Loosen the jam screw located on clevis Turn the piston rod clockwise counterclockwise turning the rod clockwise will raise the knife turning the rod counterclockwise will lower the knife as necessary Once the proper clearance has been obtained retighten jam screw ADJUSTING THE CENTER KNIFE CUT LENGTH The center cut starts approximately 4 76 mm 187 after stitching begins and ends 4 76 mm 187 before the stitching stops Both stitching and the center knife operations are controlled by the microprocessor and can be changed To change the settings see page 1 9 Stitching 4 76mm 0 187 4 76mm 0 187 Released 06 2001 1 28 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made CENTER CUTTING SETTING THE TIMING OF THE CENTER KNIFE The needles support the material as the center knife cuts The cutting occurs as the needles and the center knife descend The center knife and the needles should be at their lowest points once the cutting has been completed If the center knife is not at its l
31. eas Beiter Made _ LOOPERS 5 Continue turning the knob clockwise until the needle bar rises 2 38 mm 094 and the bottom of the needle holder sits on the second step of the gauge NEEDLE BAR NEEDLE HOLDER SECOND STEP 2 38mm 094 NEEDLE BAR RISE THROAT PLATE 6 The centerline of the needle should be in alignment with the center of the clamping screw The point of the looper should be on the centerline of the needle approximately 3 17 mm 125 above the needle eye To adjust loosen the clamping screws and move the looper holder to the right or left as necessary Once the looper holder is in the proper position re tighten the clamping screws 7 The looper should be as close to the needle as possible without deflecting with a maximum clearance of 0 11 mm 004 To adjust loosen the allen screw and slide looper to the right or left as necessary Once the proper clearance has been obtained re tighten the allen screw NEEDLES LOOPER POINT NEEDLE BLADE 3 17mm 125 d SCREW LATERAL ADJUSTMENT Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 35 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 irm LOOPERS ADJUSTING THE LOOPER HEEL TO NEEDLE SETTING As needle passes by the heel of the looper on both the upward and downward strokes it should pass as closely as possible to the heel without deflecting To adjust perform the following step
32. eater than distance Released 06 2001 1 18 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 PATCH FOLDING Setting the Distance between the Patch Guide and Brush Blades The following adjustment may vary slightly depending on the thickness of the material being used Heavier material requires more distance between the patch guide 0 and the brush blades lighter material requires less distance If after performing the following steps the correct distance has not been obtained perform the adjustment at the bottom of this page To adjust loosen nut and screw piston rod in or out in will decrease the distance out will increase the distance as necessary Once the proper distance is obtained re tighten nut Clevis Cylinder NOTE Patch folding brushes must not deflect patch guide when welting and backing material is being folded If this occurs uneven welting or needle breakage may result For heavier material perform the following steps Loosen screws and slide brush arm in or out as necessary Once the proper distance has been obtained re tighten screws Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 19 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 anu TS a mm PATCH FOLDING Installation of Brush Blades The brush arm should be removed in order to replace the brush blad
33. eavy 32 0000 0 23 1 1 2 Double Welt 850 Light Medium 32 0000 0 232 1 2 Single Welt 801 Light Medium 32 0000 0 233 1 2 Single Welt 945 Light Medium 32 0000 0 240 5 8 Double Welt 1 100 Heavy 32 0000 0 241 5 8 Double Welt 1 148 Light Medium 32 0000 0 242 5 8 Single Welt 1 230 Light Medium 32 0000 0 250 3 4 Double Welt 1 350 Heavy 32 0000 0 251 3 4 Single Welt 1 470 Light Medium 32 0000 0 252 3 4 Single Welt Overlap 2 100 Light Medium 32 0000 0 260 7 8 Double Welt 1 655 Light Medium 32 0000 0 261 7 8 Single Welt 1 669 Light Medium Released 06 2001 1 2 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE Dentes Ideas etter Made _ SPEEDWELT 1000 SPEEDWELT 1000 SPECIFICATIONS DESCRIPTION SEWING HEAD STITCH TYPE SEWING SPEED NEEDLE BITE SIZES POCKET LENGTHS STITCH DENSITY Center End LENGTH OF END DENSITY STITCHES WELT STYLES CENTER KNIFE CONTROL SYSTEM LUBRICATION SYSTEM ELECTRICAL REQUIREMENTS COMPRESSED AIR Pressure Consumption NET DIMENSIONS Length Width Height Weight GROSS DIMENSIONS Length Width Height Weight Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 Speedwelt 1000 Sewing Machine 2 Needle Chainstitch 101 Single Thread Chainstitch 1 400 Stitch Per Minute 3 8 7 16 1 2 5 8 3 4 7 8 9 5 11 1 12 E909 22
34. edwelt 1000 is available in several modes As a result the adjustments of the patch folding brushes will vary with each model The initial steps are as follows 1 Loosen nut 9 and move adjusting screw up or down until the desired dimension is obtained between the slide blocks Once the desired dimension has been obtained re tighten nut 2 Loosen lower clamp collar by loosening set screw located in the lower clamp collar Move the collar up to within 7 94 mm 312 to the top clamp collar 3 Pull cylinder rod down until it touches the adjusting screw 4 Move the lower clamp collar down by turning it until it activates the switch 5 Turn the clamp collar one more turn Re tighten the set screw Distance 6 Check the brushes for proper operation and adjust accordingly Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 21 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 D D eir m POSITIONING OF PATCH FOLDING BRUSHES MODELS MODELS 3 8 D W 725 7 16 S W O 759 1 2 S W 945 3 8 D W 661 1 2 D W 786 3 8 S W 661 1 2 D W 856 7 16 D W 690 1 2 S W 801 7 16 S W 730 38 7 16 amp 1 2 47 7 16 amp 1 2 NOTE The above clearances may vary depending upon the thickness of the material being sewn Released 06 2001 1 22 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 5
35. eleased 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 37 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 is ECE THREADING THREADING THE MACHINE The thread color should be a basic shade of the garment being sewn Thread both of the needles from left to right ADJUSTING THE THREAD TAKE UP EYELETS The function of the eyelets 0 is to provide a looser or tighter stitch which would be dependent upon the material being sewn To adjust loosen nut and move the eyelet forward or backward moving the eyelet forward would cause stitch to be ooser moving it backward would cause the stitch to be tighter as necessary Once the proper stitch has been obtained re tighten nut ADJUSTING THE STARTING THREAD Loosen screw and move actuator 9 forward or backward moving the actuator forward will increase the amount of starting thread moving the actuator backward will decrease the amount of starting thread as necessary Once the correct amount of starting thread has been obtained re tighten screw Looser Tighter Released 06 2001 1 38 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ SEW OFF ADJUSTING THE THREAD LOOP SIZE The proper size of the thread loop for the average sewing conditions is just large enough for the looper to fit into If the loop 15 too large the loop may turn ove
36. en and clamps will come up Table will go back Clamps will go down Clamps will come up Clamps will go down and the brushes will close Brushes will open Brush will close To continue sewing To cancel and the brushes will open and clamps will come up 1 7 SPEEDWELT 1000 ARE REECE Ideas etter Made PROGRAMMING THE KEYPAD 1 Turn the machine on by turning the POWER and MOTOR toggle switches to the ON position 2 Turn on the air valve 3 Push the ON switch 4 The screen will display a message similar to the one below 138 mm Pocket FRONT LOAD Total length of stitching Loading Current Count of sew position program pockets This screen pocket program briefly describes the active program in the machine It is possible to have 12 different programs The program being run is locked in memory when the machine is turned off It will be active when it is turned on again To sew a pocket welt follow the OPERATOR INSTRUCTIONS THINGS TO REMEMBER SEW INTERRUPT This switch is used to access the program by activating the keypad for about 30 seconds This safety feature prevents accidental changes made through the keypad This switch can also be used as a RETURN to the pocket program screen To keep the keypad active press any one of the following keys RST L KNIFE CTR To de activate the keypad press any of the following per screen instructions ENT HOME
37. es This is done by removing screws and the pivot block Lift the brush arm up or out Loosen screws I located on both ends of the patch folding brush arm and remove old brush blade Install the new brush blade to the full depth of the slot in the pivot Re tighten screw I at one end of the arm Place hex wrench in pivot at the opposite end of the brush arm Turn the pivot until the brush blade is taut Once the brush blade 1s taut re tighten screw I Re install the brush arm and the pivot block Re install screws H and re tighten See page 1 18 for the proper adjustment of the brush arm NOTE The brush blades have a long and short side The long side down 1s used for sewing light to medium weight materials The short side down is used for sewing medium to heavy materials When installing new brush blades ensure that both blades are inserted in the same way either with both blades with the long side down or with both blades having the short side down There are also several different size blades available for the different weight fabrics Patch Guide Arm Patch Guide Patch Folding Brush 0 79mm 03 greater than distance Folding Ss Brush Blade SES SS i Short Side e Long Side Released 06 2001 1 20 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made PATCH FOLDING Positioning of the Patch Folding Brushes The Spe
38. et the short pocket length Long Pocket Tab Short Pocket Knives Tab Knives Adjustable Stop Allen Cap Screw a Loosen the allen cap screw and move the slide block backward or forward along the scale as necessary to reach the desired length b Re tighten the allen screw Note turn on and off the two stage sewing option follow the first four steps outlined in Turning On The Automatic Patch Loader At step number 5 press 2 to enter the sequence sewing set up Step number 6 allows you to turn sequence sew On 2 or Off 1 See the Options section page 1 44 for further explanation Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 59 Outside U S Phone 804 559 5000 Fax 804 559 5210 Lr SPEEDWELT 1000 Eus SER ere mm OPTIONAL ATTACHMENTS ADJUSTMENTS Adjusting the Work Air Eject Option The length of the air blast for this option 15 controlled by a timer which has been factory set Should your sewing needs require a shorter or longer air blast the timer may be adjusted from a minimum of 5 to a maximum of 50 milliseconds To adjust 1 Press the sew interrupt switch 2 Press CTR 3 Press Input Output Test 4 Advance to the Work Eject option on the LCD screen The message should say Work Eject On 1 Work Eject Off 2 5 Push 1 6 Push the down arrow for a shorter air blast the up arrow for a longer air blast 7 Press ENT Released 06 2001 1 60 U S Phone 800 367 7332 Fax 559
39. ges 1 16 to 1 24 Adjust the loopers to the needles pages 1 32 to 4 35 Install the new trim knife to the bracket and re install the machine page 1 36 Install the new tab knives and holders page 1 19 to 1 31 Sew pockets on scrap material and check for correct stitch density center knife cut tab knife cut and for any skipped stitches Adjust the thread pick up arms page 1 39 Revised 01 97 2 8 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210
40. hone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 Better Ideas etter Made _ TAB CUTTING REPLACING THE TAB KNIVES To replace the tab knives remove knife holder by removing screw and removing the tab knife from finger shoe Remove nut and washer 9 Remove the old tab knife by sliding it off threading screw and then pulling it down and out Insert the new knife by tilting the knife up and into knife pointer and down over threaded screw Re install washer 9 and nut Re install the tab knife into the finger shoe and re tighten screw A Repeat for the other tab knife Sew a pocket on a scrap piece of paper to ensure the tab knives are central to the two rows of stitches If the tab knives are not central loosen nut and turn set screws in or out in will produce a larger cut out will produce a smaller cut as necessary Once the tab knives have been centralized re tighten nut Back edge of Tab Knife Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 31 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 AMF REECE TAB CUTTING ADJUSTING THE FRONT AND REAR TAB KNIVES The front and rear tab knives should be positioned so that the tab cuts are exactly even with the ends of stitching and also equal in distance from the sides of the stitches The side clearance between the tab knives and the stitching 9 may be
41. ion pe 2nd prick A of needles 5 6 evenly spaced stitches To verify that the stitch pattern conforms to the diagram perform the following test 1 Install pricking needles prepared from 950 class needles shortened to 1 9 16 overall and sharpened to a point 2 Place a sheet of sturdy paper under the clamp foot and operate the machine through a sewing cycle 3 Compare that stitching pattern with the diagram above 4 If the newly created stitching pattern does not match the diagram above adjustments must be made to end length end stitching and center stitches see Re programming Instructions on page 1 9 Released 06 2001 1 26 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made CENTER CUTTING REPLACEMENT OF THE CENTER KNIFE As the knife begins to dull a ragged center cut will be made The knife may be sharpened with an oil stone However if sharpening the knife does not correct the ragged cut the knife will need to be replaced A supply of sharpened and or new knives should be kept on hand for ready replacement To replace a knife perform the following steps Lift the machine Turn the air pressure OFF by turning the air valve knob half turn Loosen screws and raise the knife up and slide it out Insert the new knife into the knife holder The bottom of the new knife must touch the stop screw locate
42. just 1 Loosen the bolt and the allen screw on bumper bracket 2 Move bumper 9 backward or forward as necessary 3 Re tighten the allen screw and the bolt O 1 2 Patch Guide Needle an Back Block of Patch Load Tray Rotary Actuator Air Cylinder Released 06 2001 1 52 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARNE REECE SPEEDWELT 1000 Ideas Better Made OPTIONAL ATTACHMENTS ADJUSTMENTS Centering the Patch Load Tray When the machine is in the load position the needles should be centered with the patch load tray To adjust 1 Loosen the two adjusting screws on the patch loader arm 2 Movethe arm in or out as necessary until the patch load tray 1s centered 3 Re tighten the adjusting screws Patch Loader Patch Loader Arm Back Block Arm Patch Tray M dt OI Adjusting Adjusting n Screws A i Patch Guide M Patch Load P Needles i Screws Setting Patch Load Tray Height Clearance between the underside of the patch load tray and the top of the brushes should be approximately 1 16 1 5 mm to 3 32 2 3 mm To adjust 1 Loosen screw C to raise or lower the loader arm 2 Adjust carefully to prevent losing previous loader arm and stop adjustments Patch Tray N 4 1 16 3 32 Patch Guide Brush Blade Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 53
43. le stops in an interim position the keypad must be used to reset the table position THREAD SAFETY SWITCH The thread safety switch is used when a thread breakage occurs This switch when pressed prevents the machine from sewing enabling the operator to re thread the machine When the operator 1s ready to continue sewing the switch when pressed again returns the machine to the sewing position before the thread breakage occurred KNEE SWITCH The knee switch starts the sewing cycle Released 06 2001 1 4 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Dentes Ideas etter Made _ CONTROLS TREADLE The treadle operates by two different position switches which control the operation of the clamping table clamps and brushes Positions are halfway down Position Switch 1 and all the way down Position Switch 2 KEYPAD The keypad is locked during normal operation to avoid accidental program changes The SEW INTERRUPT switch stops the operation and activates the keypad for approximately 30 seconds Striking a key keeps the keypad active until the ENT button 1s pushed which returns the screen display to the sew program selected and locks the keypad THREAD MONITOR SWITCH This switch located under the head cover will detect a slack or broken thread and will stop the machine from sewing and initiate the repair mode THREAD MONITOR SWITCH S
44. mm STOP 1 44 LESS 1 MORE ENT To enter the sewing mode press the SEW POCKET PRESS CTR key to continue in the programming PROGRAM PRESS ENT mode press the ENT key 147 mm PROGRAM 2 NEXT CHANGE ENT TYPICAL PROGRAMS 2 THROUGH 8 Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 9 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 A UN MEE PROGRAMMING THE KEYPAD PROG POCKET PRESS 112 gt OPTIONS PRESS 2 WARNING MACH WITHOUT OPTIONS CTR WITH ENT AUTO PATCH LOADER 1 SEQUENCE SEWING 21 CZ E EE PATCH LOADER ON 1 EE OFF 2 SEMIAUTOMATIC 1 d AUTOMATIC 2 E a t 10 TUU CE UES X gt SEQUENCE OFF 1 PROG SEQUENCE 2 TWO POCKETS 2 THREE POCKETS 1 joo a ENTER POCKET NO FOR Ist POCKET 1 2 ENTER POCKET NO FOR 2nd POCKET 1 2 J ENTER POCKET NO FOR Ist POCKET 1 2 ENTER POCKET NO FOR 2nd POCKET 1 2 ENTER POCKET NO FOR 3rd POCKET 1 2 Released 06 2001 1 10 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE __ Better Ideas Beiter Made _ SPEEDWELT 1000 PROGRAMMING THE KEYPAD TO CHANGE A POCKET PROGRAM Press SEW INTERRUPT switch Press H or to select TO CHANGE THE LOADING POSITION Press SEW INTERRUPT switch Press L key
45. nk P N 32 7146 0 000 as shown in Illustration B Y INS NA AA KES ILLUSTRATION POSITION THESE TWO Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 45 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 i D irm OPTIONS 4 Remove the existing program chip and replace it with the E Prom chip from the kit making sure the notch in the chip faces to the right 5 Turn on the power and then push the Sew Interrupt button 6 Press the CTR key 7 Press the 1 key then press the 2 key 8 Pressthe key until the Encoder Count message appears 9 Press the ENT key encoder count 10 Press the HOME key encoder count then press the ENT key again 11 Press the 1 key to save the count and then push the Sew Interrupt button Released 06 2001 1 46 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Teas Hun ORK LOCATING AND DRILL HOLE LIGHTS Lights designed specifically to facilitate work location and increase positioning accuracy are available with the Speedwelt 1000 These lights project light slots on the garment which accurately fix the location for positioning work locating marks such as drilled holes which can be applied to garment on the cutting table Other types of locating marks can also be utilized such as darts seams slits and chalk marks In the production of double welt
46. opped If it is not repeat step 1 Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 41 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 Vie BLA Malle PROXIMITY SENSOR SWITCH The proximity sensor switch located under the bedplate near the main shaft tells the machine whether or not the needle is up at the end of sewing If the machine does not know needle is up it will display an error message on the keypad The sensor is activated when the eccentric stud passes in front of it When the needle bar 15 at top dead center the eccentric stud should be in front of the sensor which would activate it If the eccentric stud is not m front of the sensor adjust the synchronizer as described on page 1 40 Released 06 2001 1 42 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ CONTROL BOX The control box consists of a potentiometer and three toggle switches which normally set the functions of the machine 1 e needle bar position up or down machine slow start However in this case they have been factory set and can not be changed Connector Panel Correction Potentiometer 4 Toggle Switches Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 43 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 Press 2 to enter to Option section Press EN
47. owest point after the cutting has occurred the timing of the center knife is not correct To re set the timing perform the following steps Loosen set screw Holding the pulley 0 rotate the shaft clockwise or counterclockwise rotating the shaft clockwise will allow the knife to cut sooner rotating the shaft counterclockwise will allow the knife to cut later as necessary Once the proper timing has been obtained re tighten set screw 0 Needles and Center Knife at their lowest points Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 29 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 AMF REECE TAB CUTTING ADJUSTING THE CLAMPING MATS The inner edge of the clamping mats must be parallel and equal distance from the side of the throat plate The mats should just clear the sides of the throat plate To adjust perform the following steps Loosen screws Slide the clamping mats to the right or left as necessary Once the proper distance has been obtained re tighten screws CENTERING THE TAB KNIFE ASSEMBLY The lower ends of the tab knives should be centrally located between the clamping mats when the tab knives 9 are at the top of their stroke To adjust perform the following steps Loosen screws Slide the tab knife bracket to the right or left as necessary Once the tab knife bracket has been centered re tighten screws Released 06 2001 1 30 U S P
48. plate should be slightly more than the thickness of the material patches Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 55 Outside U S Phone 804 559 5000 Fax 804 559 5210 Lr SPEEDWELT 1000 Una eR iar ere mm OPTIONAL ATTACHMENTS ADJUSTMENTS Adjusting Patch Tray Speed The speed at which the patch load tray travels into the load position and back to its Home position can be adjusted To adjust the speed going into the load position Use a small screwdriver and turn the recessed speed adjusting screw in the air cylinder located at the front ofthe rotary actuator in for less speed or out for more speed To adjust the speed for moving the patch load tray into its Home position Use a small screwdriver and turn the recessed speed adjusting screw in the air cylinder located at the back ofthe rotary actuator in for less speed or out for more speed Rotary Actuator Rear Cylinder 66 me Speed eee Screw Load Speed Adjusting Screw Front Cylinder fi 9 JA Bracket Released 06 2001 1 56 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ OPTIONAL ATTACHMENTS ADJUSTMENTS Setting the Inside Edge of the Patch Load Tray Back Block While making the adjustments below be sure to maintain the parallel relationship between the patch guide and the side of the patch load t
49. pose of the output test is to determine whether the component PATCH LOAD IN OFF ON being tested is functioning properly BACK J NEXT I The components during this test if working properly will actually Output SAFETY RE THREAD OFF gt demonstrate their functions If thereisa Tests BOE EMI problem with the component they will 00 m not demostrate their function PRESS 2 The ENT key will cause the various CLA MPS UP DOWN ENT pieces of equipment to move either up NEXT 1 or down in or out BRUSHES IN OUT ENT The NEXT key will advance and BEC NEXT IM display the next screen of the test The BACK key will display the previous screen of the test If the machine 15 not in the proper position to perform the test a message will appear indicating what position it must be in At the same time it will allow the machine to be positioned correctly by pressing the ENT key Revised 01 97 2 4 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 AMF REECE SPEEDWELT 1000 Bette Ideas Better Wade TROUBLESHOOTING J SV2 C KNIFE UP DOWN ENT BACK J NEXT 7 SV 3 The THD HOLD 1s the output test perd for the thread pick up finger BACK 1 DH TABLE NOT BACK PRESS ENT Revised 01 97 U S Phone 800 367 7332 Fax 559 5210 CLAMPS NOT DOWN PRESS ENT BRUSHES NOT IN PRESS ENT SV 4 TABKNIFE UP DOWN
50. quare with the sewing work retighten screws 9 2 The lamp should be centered over the lens in order to centralize lens projection and to obtain maximum intensity To adjust loosen screw and move the lamp as necessary Once the lamp is centralized over the lens retighten screw Note In some materials the light slots are clearer as the garment is being moved into position than when the garment rests in position Therefore while setting the lights use material where the light slots are clearly visible when in the resting position Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 47 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ug ily et ete WELTING MATERIAL Welting material consists of welting patch garment material backing patch pellon L 35 and stay material cotton silesia Backing Patch Welting Patch AA E n nee er Garment Stay Material Stay Le Material Weltino Patch Garment Material Welting patch length is 1 longer than the actual welt For the best result patches for horizontal welts should be cut crosswise to salvage except where stripes in the material are over 1 4 in width vertical or diagonal welt patches should be cut parallel to the salvage Length 1 Length of Welt Backing Patch Pellon Backing patch length is the same as Welting Patch 1 longerthan the welt For double welting u
51. r towards the front causing the looper to miss it This 15 what causes skipping To adjust perform the following steps Loosen set screw Raise or lower looper wire raising the looper wire will increase the loop size lowering the loop wire will decrease the loop size as necessary Once the proper loop size has been obtained re tighten set screw O Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 39 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SEW OFF THREAD PICKUP ARMS The thread pickup arms 0 are designed to pass just below and beyond the needles grasping the thread taut before trimming Select the OUTPUT Test from the keyboard menu see pages 2 4 through 2 6 Select the thread holder option by pressing the up arrow Press the ENTER key The thread pickup arms will extend and hold that position A minimum clearance of 1 59 mm 063 15 required between each needle point and its pickup arm To adjust perform the following steps 1 Loosen screw and move the pickup arms front or back as necessary Once the proper position has been obtained re tighten screw 2 Loosen screws and move the pickup arms to the right or left as necessary in order to align with needle thread Once the proper alignment has been obtained re tighten screws 9 3 To obtain distance between the needle and pick up hook loosen screws and move the pickup arms up or down as necessary Once the proper
52. ray Once adjustments are complete run the patch loader several times and make sure there 1s no binding 1 Return the clamp table to the back position 2 Loosen screw to loosen stop 3 Push the knee control and determine the extreme forward movement of the patch load arm It 1s not unusual to have to push the knee control several times to make this determination 4 With the patch loader at its most forward point set the patch load arm so that the sides of the patch tray are parallel with the side of the patch guide 5 Set the stop so that it lightly touches the patch load arm while it is in the load position Then make sure no bounce or binding exist when the loader makes contact with the step by manually operating the patch loader several times at this setting 6 Hold the load arm against the stop and position the inside edge of the patch tray back block 1 2 2 7 mm from the needles B 7 Patch Gl Needle Back Block of Patch Back Block of Load Tray Patch Load Tray Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 57 Outside U S Phone 804 559 5000 Fax 804 559 5210 LL SPEEDWELT 1000 nay ee OPTIONAL ATTACHMENTS ADJUSTMENTS Turning the Automatic Patch Loader On and Off To active or deactivate the automatic patch loading option 1 Press the sew interrupt switch 2 Press CTR on the control pad 3 Press 2 4 Press 2 again The LCD screen message should now read Without
53. readle using the appropriate foot switch position The keypad display will toggle between ON and OFF If it does not a problem exists in the switch circuitry Tab Knife Up and Tab Knife Down Lift the machine Located in the front of the machine are two micro switches one on top of the other To test the Tab Knife Up push the top micro switch in and hold The keypad will display ON when released the keypad will display OFF To test for the Tab Knife Down push the bottom micro switch in and hold The keypad will display ON When released the keypad will display OFF If it does not a problem exists in the micro switch circuitry Brushes In With the machine still lifted LOE 1 OFF ON push the micro switch located on the air BACK J NEXT 7 cylinder in and hold The keypad will display ON when released the keypad FOOT SWITCH 2 OFF 0 will display OFF If it does not a problem BACK 1 NEXT f M exists in the switch circuitry RTT BACK J E Safety Re Thread Push the Safety Re Thread button in and hold The keypad TAONE DOWN ON OFF will display ON when released the BACK NEXT 1 Y keypad will display OFF If it does not a problem exists with the button switch BRUSHES IN OFF circuitry BACK J NEXT T T Patch To exit and return to the sewing mode Loader ON Ey press CTR To perform output tests Messages el AET 0 press 2 PATCH LOAD MID ON Ly BACK J NEXT 1 7 The pur
54. s LOOPER HOLDER Loosen the clamping screw located on the drive shaft assembly Rotate the eccentric stud clockwise or counterclockwise rotating the stud clockwise will move the heel of the looper away from the needle counterclockwise will move the heel closer to the needle as necessary Once the heel of the looper is 1 the proper position re tighten the clamping screw CONNECTING ROD LOOPER ARM Released 06 2001 1 36 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 __ Better Ideas Beiter Made _ SEWING THREAD TRIMMING At the end of the sewing cycle the clamp table moves forward During this movement the inside legs of the thread loops come in contact with the trimming knife cutting the thread NOTE Never sew with a dull knife This will cause the thread to break close to the last stitch which could cause a ravling back of the stitching SHARPENING THE TRIMMING KNIFE Lift the machine Loosen screws 0 and remove the knife holder from the looper blocks it is not necessary to remove the knives from the holder Stone the trimming knife to a sharp edge It is imperative that the bevel be maintained on the underside of the knife Once the knife has been sharpened re install the knife holder into the looper blocks ensuring that the knife points are centered to the loopers Once they are centered re tighten screws 0 Thread R
55. sack coat pockets utilizing drilled holes for locating marks the forward lantern should be positioned so that when the forward hole is located in the hairline cross point it will accurately establish the starting point on every garment The rear hole will provide accurate pocket alignment as long as it falls anywhere along the vertical light slots ofthe rear lantern The same hole drilling pattern may be used on double welt work for all sizes since the pocket length is controlled by the SpeedWelt 1000 machine CAUTION Avoid drilling holes in the tab areas of the welt The drilling may shred or reduce a tab area so that an effective tab can not be formed In single welt work the rear hole should also be accurately located because it is the starting point on alternate pocket operations To focus the light slots perform the following steps 1 Loosen screws 0 and move the lens carriers up or down as necessary Once the light slots are focused retighten screws 0 2 The bracket angle may need to be changed if the folding brushes obstruct light projection when the clamp foot is raised This is done by loosening nut 9 and moving the bracket up or down as necessary The bracket may need to be bend slightly Once the bracket is in the proper position retighten nut To square light slots with sewing work perform the following Steps 1 Loosen bracket by loosening screws and rotating the lights as necessary Once the lights are s
56. se patches with 1 4 end slits For single welting and knits use patches without end slits Pellon L 35 1s recommended Slit Length 1 Length of Welt Released 06 2001 1 48 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ANI F REECE SPEEDWELT 1000 _ Better Ideas Better Made _ WELTING MATERIAL Stay material is used for pockets on coats and coat linings The pocket bag is used in place of the stay material in making trouser pockets Stay material should be cotton silesia with sizing This material is available in rolls of various widths with perforations every 8 The perforations aid in allowing the operator to separate the stay material while the machine is sewing Below is a chart which displays the various widths of welting material Welting Patch Backing Patch Stay Material 2 1 2 2 for Trouser Application 2 12 3 4 4 to 4 41 4 3 12 2 to 3 Overlapping Welt 5 1 4 to 5 1 2 9 2 t0 3 1 2 7 8 A A 3 3 4 3 Single Welt 4 3 1 2 Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 49 Outside U S Phone 804 559 5000 Fax 804 559 5210 NA j SPEEDWELT 1000 A me mead LUBRICATION It is important to oil the machine daily The table must be in the front loading position in order to reach all oil points The locations of the oil points are indicated with arrow displayed in the diagram below CEZ ro he e
57. the tab cut to end of stitch may need to be further adjusted Released 06 2001 1 32 U S Phone 800 367 7332 Fax 559 5210 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWELT 1000 _ Better Ideas etter Made LOOPERS The following diagrams illustrate the sequence of looper and needle action for each stitch When the needles rise 2 38 action continues the the down stroke Just before being cast mm 094 from the bottom of loops should slide to the needle should enter on to the needles their stroke the looper points heel of the looper the thread loop should enter thread loops LOOPER SHAFT ASSEMBLY The front edge of the looper shaft to the back of the needle points should measure 2 38 mm 094 This is a factory setting and must not be changed The looper shaft is fixed in position when the bearing blocks 9 are installed To check this distance move the looper holders to one side and measure using the 03 0145 0 000 gauge If the measurement is not 2 38 mm 094 adjust by the following steps Loosen the machine head by loosening the 9 screws located in the back and on both sides of the head Slide the machine head forward or backward as necessary Once the proper measurement has been obtained retighten the 9 screws Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 33 Outside U S Phone 804 559 5000 Fax 804 559 5210 ARE REECE SPEEDWE
58. to the front and rear rocker levers using the pins to secure them in place Re install E rings over the pins Remove eccentric and rear studs Re install the rocker rod assembly 9 using the studs and pin 0 ROCKER ROD TENSION 1 The tension is adjusted on the rocker rods by rotating the eccentric stud This is done by removing the needle holder and pin 0 2 Loosen eccentric stud Rotating the stud so the arrow faces the front of the machine increases the tension on the rocker rods rotating the stud so the arrow faces the rear of the machine decreases the tension Decrease the tension enough so the needle bar can move up and down freely Slowly increase the tension until there 15 a slight drag when the needle bar is moved manually up and down The arrow will be about at the or 2 o clock position Re tighten stud Released 06 2001 U S Phone 800 367 7332 Fax 559 5210 1 13 Outside U S Phone 804 559 5000 Fax 804 559 5210 SPEEDWELT 1000 ARE REECE Ideas Better Made ADJUSTING NEEDLE BAR HEIGHT 1 Move the clamping table to the back load position 2 Remove the patch guide assembly by loosening and removing screws 3 Move the clamping table to the front load position 4 Set the gauge squarely on the throat plate The bottom of the needle holder should sit on the first step of the gauge with the needle bar at the bottom dead center Adjust the needle bar to this height by loosening the clamping s

Service Manual

Contents

Download Pdf Manuals

Related Search

Related Contents