LESLIE 8010 CONSOLE CONNECTOR KIT FOR
Contents
1. 2 048116 Switch Retainer 2 048108 Switch Only 029629 Switch Only 042911 4 ckt Plug 042101 3 ckt Plug 042085 Insert 023309 Insert 023309 ORDERING PARTS Standard hardware connectors and electronic components should be purchased locally Non standard items may be obtained through a Leslie speaker dealer Orders should include part numbers shown above Page 4 of 42. D adapter wire Strip 1 4 inch and connect all three using the wire nut provided D Connect the GREEN adapter wire to the SIGNAL terminal on the console speaker E Connect the BLACK adapter wire to the extra tab on the GROUND terminal on the console speaker DO NOT REMOVE THE BLACK WIRE ATTACHED F Adjust the volume as outlined in the Leslie Service Manual Page 2 of 4 FUSE SWITCH CONTACTS POSITION MADE mes wont SWITCH CONTACTS POSITION MADI BROWN WN RED BLACK Ware Fig 1 BROWN BROM CIRCUIT BOARD PARTS SIDE R4 EN IOW 5 ka a ORMER RED YEL Bansin REFORMER TSW R3 PIN 5 Fig 2 042770 Adapter Plug amp Socket Pin Layout 3 ILo o 4 4 Na UN gosh AR oo p2 ga 1 O 3 4 4 NG 2 2lo 050 85 8 PI si P4 s5 Fig 4 Page 3 of 4 PARTS LIST CONSOLE CONNECTOR CONSOLE ADAPTER Chassis 041921 P2 023259 TI 048025 P2 Insert 023309 Cl 018093 p4 021238 R1 024117 S5 033670 R2 018457 S3 Cap 029231 R3 048157 R4 022343 S1 042093 S2 042119 S3 042077 Insert 023556 Circuit Assy 039032 Fuseholder 055178 Fuse 029280 ECHO CONTROL TREMOLO CONTROL Echo Switch Case Tremolo Switch Case brown 029199 brown 012260 ebony 029207 ebony 012278 ivory 029215 ivory 012286 Switch Case Cover Switch Case Cover brown 048702 brown 048702 ebony 048710 ebony 048710 ivory 048728 ivory 048728 Switch Knob Switch Knob brown 048066 brown 048066 ebony 048074 ebony 048074 Switch Retainer
3. LESLIE 8010 CONSOLE CONNECTOR KIT FOR HAMMOND ORGANS M 100 122 222 122RV 142 222 222 RV L 100 SERIES 122 142 222 M 1 2 3 122 122V 122RV 222 222RV 142 CONTENTS OF KIT 1 Console Connector 038208 1 Tremolo Control 1 Console Adapter 042770 brown 042168 1 6 Conductor Cable 017277 ebony 042176 1 Instructions 034587 ivory 042184 6 Insulated Staples 028464 1 Oiler 052035 1 Echo Control 2 Screw 8 x 1 2 029132 brown 042200 4 Screw 6 x 1 2 029124 ebony 042218 1 Tab Connector Male 029371 ivory 042226 2 Tab Connector Female 029389 Wire Nut 028076 TO INSTALL THE KIT 1 Mount the Echo and Tremolo control switches to the wooden rail in front of the lower manual using the wood screws provided 2 Route the control cables under the lower manual through the keyboard shelf and into the amplifier section of the console If no opening is provided drill a 1 hole in the keyboard shelf just under the lower manual 3 Mount the console connector chassis inside the console within reach of the adapter and control cables using the wood screws provided 4 Plug the Echo and Tremolo control cables into the proper sockets on the connector chassis 5 Plug the Leslie Speaker cable into the socket on the connector chassis 6 Plug the 6 CKT adapter plug into the 6 CKT socket on the connector chassis 7 Connect the BLUE and GRAY adapter wires to the SWITCHED 117 VAC terminals on the console amplifier Page 1 of 4 M1
4. M2 A Remove the 5 pin plug and socket assembly from the adapter It is not used in this installation B Remove the GREEN speaker wire from the OUTPUT terminal on the console amplifier and connect it to the screw terminal on the GREEN adapter wire C Connect the RED adapter wire to the speaker OUTPUT terminal on the console amplifier D Connect the BLACK adapter wire to the speaker OUTPUT terminal to which the BLACK speaker wire is connected DO NOT REMOVE THE BLACK WIRE ATTACHED E Adjust the volume as outlined in the Leslie Service manual M3 A Remove the 5 pin SPEAKER plug from the console amplifier and plug it into the 5 contact adapter socket B Insert the 5 pin adapter plug into the SPEAKER socket on the console amplifier C Adjust the volume as outlined in the Leslie Service Manual L 100 M 100 A Cut the wires connecting the 5 pin plug and socket assembly to the adapter at a point just behind the screw terminals It is not used in this installation B Strip the wires 1 4 inch and solder the tab connectors provided to the wires as follows RED Male BLACK Female GREEN Female C Remove the GREEN wire from the SIGNAL terminal on the console speaker and connect it to the RED adapter wire Insulate with plastic sleeve provided NOTE On some models both a RED and GREEN wire are connected to this terminal If this is the case remove the tab connectors from the RED and GREEN speaker wires and the RE
Download Pdf Manuals
Related Search