Obs Slid Dr 10.2
Contents
1. hold handle in place 2 Remove lock turn lever from interior of door panel See illustration 1 3 Slide the door 10 Reposition panel open interior From edge of handle on the panel locking stile and stile remove vi install fo A Foam lt g 7 screws at top iai machine ii gasket and bottom of urn 1 p N S Exterior screws Thumb turn 1 al Exterior the lock Pull A gone through wl handle mortise lock out LFI interior ea Foam gasket of the stile See a handle and oo k 2 f illustration 1 secure See Multi point Pp illustration 4 mortise lock 1 Interior handle 1 Mon pan lt A mortise lock 1 Interior handle 1 i SCIEWS 4 2 machine screws 2 1 11 Check lock operation with panel open the turn lever Measure existing mortise to find horizontal center line With a pencil or tape transfer this line to interior and exterior face of stile near the edge Position routing jig on stile as shown and align center mark on guide with marks on stile Fasten jig with 8 x 1 3 4 flathead wood screws supplied check alignment See illustration 2 Center mark of existing mortise o Mortise routing jig A AIN 8 x 1 3 4 screws 2 YZ 19913260 2 2005 12 13 10 2 6 should operate freely with minimal res2. OBSOLETE DOORS SLIDING DOORS TRIMLINE PATIO DOOR DUAL POINT MORTISE LOCK UPGRADE MARVIN Windows and D Built around you STANDARD PARTS SHIPPED 5 Setup router to remove 1 1 8 1 64 of wood from the Dual point mortise lock with screws stile Route mortise to dimension of guide Dual point keeper with screws 6 Remove guide and clean all wood shavings from mortise area Remove reference marks from interior and exterior of stile Keeper marking template Mortise routing guide Router collar guide 7 Install mortise lock 1 2 straight router bit assembly into edge rey YOU WILL NEED TO SUPPLY of the stile Check Multi point Safety glasses Hearing protection mortise clearances A mortise lock Phillips screwdriver Standard screwdriver is a ae Ne eee Plunge router preferred or standard base router stile modify mortise Drill Driver with Phillips bit if needed Attach Use extreme caution and observe all safety precautions with screws i Strike and guidelines supplied K screws 2 See illustration 3 gt y Update Procedures 3 1 Unlock the mortise lock Remove Phillips head machine 8 screws from interior handle assembly Remove interior and exterior handles from stile See illustration 1 Replace the lock turn lever on interior as shown in illustration 4 9 Position exterior handle on the stile if equipped line up and insert keyed cylinder actuator pin into mortise lock
3. er operation Adjust hook until slight resistance is felt at the end of turn lever travel and panel is drawn snug against locking jamb Repeatfinal adjustment procedures for remaining latch hook See illustration 5 hao Operator locking stile Strike screws 2 Strike placement template Lock template in place X lt zS Interior handle Multi point mortise lock Exterior sheathing tudwall Operator side jamb 2 D Shims Strike Screws AELOD 10 2 7 MARVIN Windows and D Built around you Marvin Service Manual 11708609
4. istance IMPORTANT If replacement keeper screws are longer than original screws AND you are attaching keeper to a stationary panel stile You MUST use screws that are the same length as existing screws Failure to do this may result in severe damage to the stationary panel insulating glass unit Unlock mortise lock insert 2 keeper mounting screws through template provided as indicated Lock template with screws into mortise lock Close panel against locking jamb panel to mark keeper location Remove template from lock Remove keeper screws from template position keeper on jamb panel attach with screws Place shims between the jamb and rough opening at top and bottom of keeper when applying to a locking jamb See illustration 5 Check vertical alignment of strike to latch hooks Adjust as needed by loosening screws and sliding strike up or down Marvin Service Manual 11708609 OBSOLETE DOORS SLIDING DOORS TRIMLINE PATIO DOOR DUAL POINT MORTISE LOCK UPGRADE 14 After latch and strike are aligned adjust latch hooks by rotating adjustment screws above below hooks with a standard screwdriver Before final adjustments are made with operating panel fully closed check to see if any resistance is felt when operating the turn lever extend latch hooks as needed until lever operates freely Then adjust one latch hook at a time rotate adjustment screw to draw latch hook into the lock in small increments close the panel and check lev
Download Pdf Manuals
Related Search