Path-Pro - Snow Blowers Direct
Contents
1. 6 Position scraper assembly under housing See Figure 10 D shaped cutout must be on the left Edge must point down and forward Scraper assembly bolt holes must align with square bolt holes in auger housing 1 Scraper Blade Edge Figure 10 7 Move scraper assembly backward and up until small lip on top of scraper blade contacts bottom lip of housing 8 Install bolts and nuts Tighten nuts to 40 50 in lbf Threads must protrude beyond the nut 9 Return unit to operating position IMPORTANT If auger paddles are pulling too strongly or scraper blade is not clearing completely loosen nuts do not remove and slide scraper assembly down slightly Tighten nuts Adjust Remote Chute Rotation Cables Model 938033 1 Move engine switch Item 16 to OFF position and remove key Allow unit to cool 2 Open fuel and oil door Item 22 to access chute rotation cable adjustment screws 3 Loosen chute rotation cable adjustment screws See Figure 11 1 Chute Rotation Cable Adjustment Screws Figure 11 4 Pull cable covers to the right to remove slack 5 Tighten screws and close fuel and oil door IMPORTANT Remote chute rotation cables may also be accessed from under unit by tipping unit forward FOR BEST PERFORMANCE For complete snow removal walk slowly and slightly overlap each path previously taken Position discharge chute downwind when possible e Do not pick2. LIMITATION OF REMEDY AND DAMAGES Ariens Company s liability under this warranty and under any implied warranty that may exist is limited to repair of any defect in workmanship and repair or replacement of any defective part Ariens Company shall not be liable for incidental special or consequential damages including lost profits Some states do not allow the exclusion of incidental or consequential damages so the above limitation or exclusion may not apply to you AUSTRALIAN CONSUMER LAW The following applies solely to warranties subject to Subsection 102 1 of the Australian Consumer Law Our goods come with guarantees that cannot be excluded by the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure DISCLAIMER OF FURTHER WARRANTY Ariens Company makes no warranty express or implied other than what is expressly made in this warranty If the law of your state provides that an implied warranty of merchantability or an implied warranty of fitness for particular purpose or any other implied warranty applies to Ariens Company then any such implied warranty is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so t
3. OPERATOR ZONE This unit is designed to be operated by one person located in the operator zone see Figure 3 Sq 2 Operator Zone Figure 3 EN 9 CONTROLS AND FEATURES Figure 4 PON oo oOo ON 10 11 Handlebar Auger Control Bar Auger Control Cable Assembly Remote Discharge Chute Handle Assembly Model 938033 Recoil Starter Handle Discharge Chute Handle Models 938030 031 032 034 Discharge Chute Deflector Handle Discharge Chute Wing Knob Auger Paddle Oil Fill Models 938030 034 12 Oil Fill Models 938031 032 033 13 Oil Drain Plug 14 Fuel Cap amp Tank 15 Choke Control Knob 16 Engine Switch 17 Primer Bulb 18 Electric Start Button Models 938032 033 034 19 Power Cord Receptacle Models 938032 033 034 20 Fuel Shut off Valve 21 Engine Guard 22 Fuel amp Oil Door EN 10 OPERATION CONTROLS AND FEATURES WARNING AVOID INJURY Read and understand the entire Safety section before proceeding See Figure 4 for all controls and features locations Engine Switch Item 16 The engine switch has two positions 1 1 OFF Engine will not start or run 2 ON Engine will start and run Choke Control Knob Item 15 1 START Choke Closed Chokes off air to engine for easier starting
4. THE KING OF SNOW Path Pro Owner Operator Manual Manuel du Propri taire Utilisateur Models 938030 SS21 SN 000101 938031 SS21 SN 000101 938032 SS21E SN 000101 938033 SS21EC SN 000101 938034 SS21E SN 000101 The use of any gasoline exceeding 10 ethanol E10 or Se 10 MTBE will void the product warranty j L utilisation d une essence contenant plus de 10 d thanol E10 ou de 10 de MTBE annulent la garantie EN ENGLISH i FRAN AIS 04535800B 7 14 Printed in USA TABLE OF CONTENTS SAFETY 4 CONTROLS AND FEATURES 10 OPERATION 11 MAINTENANCE SCHEDULE 17 STORAGE 18 TROUBLESHOOTING 19 SERVICE PARTS 20 SPECIFICATIONS 20 ACCESSORIES 20 WARRANTY 21 INTRODUCTION THE MANUAL Before operating unit carefully and completely read your manual The contents will provide you with an understanding of safety instructions and controls during normal operation and maintenance ENGINE MANUAL The engine on this unit is covered by a separate manual specific to the engine This manual is included in the literature package that shipped with the unit Refer to this manual for engine service recommendations If the engine manual is not available contact the engine manu
5. 2 RUN Choke Open Allows for normal operation IMPORTANT Gradually open choke after engine starts Fuel Shut off Valve Item 20 IMPORTANT The fuel shut off valve MUST be in the closed off position before transporting the unit The valve is closed when it is narrow and vertical when viewed from above The fuel shut off valve has two positions 1 OFF Use this position to service transport or store the unit 2 ON 2 Use this position to run the unit Primer Bulb Item 17 Pushing primer bulb adds fuel to engine for easier start See Start Engine Recoil Start on page 13 Recoil Starter Handle Item 5 When pulled handle will start engine See Start Engine Recoil Start on page 13 IMPORTANT Do not let handle snap back against handlebar Electric Start Button Models 938032 033 034 Item 18 When pushed button will start a properly choked and cranked engine See Start Engine Electric Start on page 13 Discharge Chute Item 8 Turn discharge chute handle Item 6 to control direction of snow discharge Remote Discharge Chute Handle Assembly Item 4 Model 938033 Move remote discharge chute handle forward or backward to control direction of snow discharge EN 11 GASOLINE IMPORTANT Always use gasoline that meets the following guidelines Clean fresh gasoline A minimum of 87 octane 87 AKI 91 RON High altitude us
6. discharge towards persons or property that may be injured or damaged by thrown objects Danger ROTATING PARTS ONLY use clean out tool to clear blockages NEVER use your hands High speed auger impeller rotates below discharge opening Wait for all moving parts to stop before removing clogs or servicing dE Danger Read Owner Operator Manual Do not operate in rain EN 5 4 DANGER Danger ONLY use clean out tool to clear blockages NEVER use your hands Never direct discharge towards persons or property that may be injured or damaged by thrown objects Keep people away from unit while operating Keep children out of work area and under watchful care of a responsible adult gt Stop engine remove key read manual before making any repairs or adjustments Read Owner Operator Manual Wear appropriate hearing protection RULES FOR SAFE OPERATION This snow thrower is capable of amputating hands and feet and throwing objects Failure to observe the following safety instructions could result in serious injury The following safety instructions are based on the B71 3 specifications of the American National Standards Institute in effect at the time of production Training Read understand and follow all instructions on the machine and in the manual s before operating this unit Be thoroughly familiar with the controls and th
7. ice or other debris Clean up oil or fuel spills Never allow anyone to operate this unit when their alertness or coordination is impaired Always keep protective structures guards and panels in good repair in place and securely fastened Never modify or remove safety devices Avoid sharp edges Sharp edges can cut Do not throw snow any higher than necessary Clearing a Clogged Discharge Chute Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters space heaters or clothes dryers Allow the engine to cool before storing in any enclosure or covering the unit Hand contact with the rotating auger impeller inside the discharge chute is the most common cause of injury associated with snow throwers Never use your hand to clean out the discharge chute Always refer to operator s manual for important details if the snow thrower is to be stored for an extended period Maintain or replace safety and instruction labels as necessary To clear the chute 1 SHUT THE ENGINE OFF 2 Wait 10 seconds to be sure the auger impeller blades have stopped rotating 3 Always use a clean out tool not your hands Run the machine a few minutes after throwing snow to prevent freeze up of the auger impeller EN 8 Personal Protection Do not operate the equipment without wearing adequat
8. in material and workmanship for the time period noted in the chart below Equipment put to personal use around a single household or residence is considered Consumer Use equipment put to any business use agricultural commercial or industrial or used at multiple locations is considered Commercial Use If any product is rented or leased then the duration of these warranties shall be 90 days after the date of purchase An authorized Ariens dealer Ariens brand products Gravely dealer Gravely brand products Parker dealer Parker brand products or Countax dealer Countax brand products will repair any defect in material or workmanship and repair or replace any defective part subject to the conditions limitations and exclusions set forth herein Such repair or replacement will be free of charge labor and parts to the original purchaser except as noted below Warranty Warranty Period Warranty Period Code Product Group Consumer Use Commercial Use PA Log Splitters Brushes String Trimmers Edgers 3 Years 90 Days PB Professional Powered Brushes 3 Years 1 Year PC Tillers 2 Years 90 Days Vacuums Blowers Sweepers Truck Loaders PD Lawn Rakes Sprayers Aerators etc 1 Year 1 Year PE Pressure Washer Generators 3 Years 1 Year SA Professional Sno Thro 3 Years 1 Year SB Compact Deluxe Platinum AMP Sno Thro 3 Years 90 Days Path Pro SC Sno Tek 2 Year
9. information 4 Replace cap and close door To add oil 1 Turn engine off and let cool for at least three minutes 2 Open fuel and oil door Item 22 and remove cap from oil fill 3 Add 5W 30 oil and replace cap Do not overfill 4 Clean up any spilled oil and close door Models 938030 034 To check oil level 1 Turn engine off and let cool for at least three minutes 2 Remove cap from oil fill Item 11 3 Check oil level on dipstick Oil level must be maintained at safe operating level See SPECIFICATIONS on page 20 See Engine Manual for detailed information 4 Replace cap EN 12 To add oil 1 Turn engine off and let cool for at least three minutes 2 Remove cap from oil fill Item 11 and add 5W 30 oil Do not overfill 3 Replace cap 4 Clean up any spilled oil TRANSPORTING UNIT 1 Always shut off engine remove key and close fuel shut off valve when transporting on a truck or trailer 2 Use extra care when loading or unloading onto truck or trailer Do not lift using discharge chute handle Item 6 3 Secure unit chassis to transport vehicle Never secure from rods or linkages that could be damaged 4 Do not transport unit while engine is running OPERATION Start Engine Recoil Start 1 Check oil level See Engine Oil on page 12 2 Position discharge chute Item 8 ina safe direction 3 Move engine switch Item 16 to ON position 4 Open fuel shut off valve Ite
10. remove key allow moving parts to stop Allow hot parts to cool Use only attachments and accessories approved by the manufacturer of the snow thrower such as wheel weights counterweights or cabs This product is equipped with an internal combustion type engine Do not use unit on or near any unimproved forest covered or brush covered land unless exhaust system is equipped with a spark arrester meeting applicable local state or federal laws A spark arrester if it is used must be maintained in effective working order by operator Make sure the equipment is in safe working condition Check shear bolts and other bolts and hardware at frequent intervals for proper tightness If components are worn or damaged replace with manufacturer s recommended parts Check clutch and brake operation frequently Do not change engine governor settings or over speed engine Adjust and service as required All motion of drive wheels and auger impeller must stop quickly when control levers are released Never operate the snow thrower without good visibility or light Falling snow fog etc can reduce vision and cause an accident Always maintain unit in safe operating condition Damaged or worn out muffler can cause fire or explosion Never operate unit after or during the use of medication drugs or alcohol Safe operation requires complete and unimpaired attention at all times Keep unit free of
11. up gravel and rocks Push down slightly on handlebar to avoid picking up debris Inspect auger before each use and remove any accumulation debris Check oil level before each use Clean unit after each use EN 16 MAINTENANCE SCHEDULE WARNING AVOID INJURY Read and understand the entire Safety section before proceeding IMPORTANT Proper maintenance can prolong the life of unit The following chart shows the recommended service schedule Interval Task Action Clean unit Remove snow and debris with a soft bristled brush Do not use harsh abrasives or cleaners NOTICE Protect painted surfaces with Each Use automotive type wax Check engine oil See Engine Oil on page 12 Follow engine maintenance schedule Perform scheduled engine maintenance Refer to Engine Manual for detailed instructions Every 10 Hours Check fasteners Check all fasteners Replace missing or damaged fasteners Tighten all nuts and bolts to correct torque values Check auger paddle wear Replace when auger paddles are worn to wear indicator holes See Replace Auger Paddles on page 14 Check scraper blade wear Do not allow scraper blade to wear down too far or auger housing will become damaged See Replace Scraper Blade on page 15 As Needed Check belt wear Adjust auger cable as needed Replace when damaged or when auger stops or stutters during operation See Repla
12. wear indicator holes See Figure 5 1 mms 1 Wear Indicator Hole Figure 5 IMPORTANT Always replace auger paddles in pairs Do not replace one paddle only See MAINTENANCE SCHEDULE on page 17 1 Move engine switch Item 16 to OFF position and remove key Allow unit to cool 2 Tip unit back onto engine guard Do not tip further than engine guard allows or oil may leak out of engine 3 Remove six hex bolts and nuts per paddle Discard hardware spacers and paddles See Figure 6 NOTICE Do not remove center plate 2 Cw 1 Bolt and Nut Locations 2 Paddle 3 Center Plate Figure 6 4 Position new paddles with wear indicator holes on the left side as you face the unit 5 Install spacers into paddle holes and secure paddle with new hex bolts and nuts 6 Tighten nuts to 50 90 in Ibf Do not overtighten 7 When both paddles are installed rotate auger paddles by hand Ensure that paddles do not rub on housing and are tightly attached Return unit to operating position Remove slack from auger cable See Adjust Auger Cable on page 15 O EN 14 Adjust Auger Cable See Figure 7 Move engine switch Item 16 to OFF position and remove key Allow unit to cool 2 Slide plastic sleeve up to auger control bar 3 Insert Z hook into appropriate hole in adjustment bracket When auger control bar is disengaged there should minor slack
13. G This snow thrower is capable of crushing or amputating body parts Failure to observe the safety instructions in the manuals and on decals could result in serious injury or death Tragic accidents can occur if the operator is not alert to the presence of children Never assume that children will remain where you last saw them Gasoline is extremely flammable and the vapors are explosive handle with care Stop engine and allow moving parts to stop before leaving operator s position Read these safety rules and follow them closely Failure to follow these rules could lead to loss of control of unit severe personal injury or death to you or bystanders or result in damage to property or the machine Safety Alert Symbols These are safety alert symbols They mean e ATTENTION YOUR SAFETY IS INVOLVED When you see this symbol BECOME ALERT OBEY THE MESSAGE SIGNAL WORDS The safety alert symbols above and signal words below are used on decals and in this manual Read and understand all safety messages 1 Danger DANGER Indicates an IMMINENTLY HAZARDOUS SITUATION If not avoided WILL RESULT in death or serious injury 2 Warning WARNING Indicates a POTENTIALLY HAZARDOUS SITUATION If not avoided COULD RESULT in death or serious injury 3 Caution CAUTION Indicates a POTENTIALLY HAZARDOUS SITUATION If not avoided MAY RESULT in m
14. al sources of ignition TO TAKE THE UNIT OUT OF STORAGE 1 See the Engine Service Manual to prepare engine for service 2 Put fresh clean fuel in the fuel tank 3 Begin the maintenance schedule EN 18 TROUBLESHOOTING Problem Probable Cause Correction Engine will not start Engine switch in OFF position Move switch to ON position see Engine Switch on page 11 Fuel shut off valve in OFF position Move valve to ON position see Fuel Shut off Valve on page 11 Fuel tank empty Fill fuel tank with fuel see Gasoline on page 12 Cord not plugged in electric start models only Plug power cord in or replace worn cord Reset circuit breaker Engine not primed Press the primer bulb twice and start engine Spark plug disconnected Connect spark plug Choke open cold engine Turn choke see Choke Control Knob on page 11 to CLOSED position then press primer button and start engine Engine flooded Turn choke to ON position and crank the engine repeatedly until it starts Faulty spark plug Replace spark plug Faulty engine See your Ariens Dealer Engine starts hard or runs Fuel mixture too rich Turn choke to OPEN position See Choke Control Knob on page 11 Faulty fouled or incorrectly gapped Clean and properly set spark plug gap or see your Ariens Dealer poorly spark plug Fuel cap vent is Cle
15. ar vent blocked Excessive Loose parts or damaged Stop engine immediately Replace auger paddles vibration auger paddles See Replace Auger Paddles on page 14 or see your Ariens Dealer Excessive snow left behind Scraper blade is worn Replace when damaged or when scraper blade has been adjusted down as far as possible and does not touch ground or clear properly See Replace Scraper Blade on page 15 or see your Ariens Dealer Snow does not Auger drive belt is loose or damaged Replace belt or adjust auger control cable See Replace Belton page 15 See Adjust Auger Cable on page 15 See your Ariens Dealer Discharge chute is Stop engine immediately Clean discharge chute excessive play discharge clogged with snow and auger housing DO NOT use your hands Auger paddles are worn Replace auger paddles See Replace Auger or damaged Paddles on page 14 or see your Ariens Dealer Remote Remote chute rotation Adjust remote chute rotation cables See Adjust discharge chute cables are loose Remote Chute Rotation Cables on page 16 or see handle has your Ariens Dealer EN 19 SERVICE PARTS ACCESSORIES See your authorized Ariens dealer for See your authorized Ariens dealer to add genuine OEM service parts these optional accessories to your unit Part No Qty Descripti
16. ce Belt on page 15 Replace scraper blade Replace when damaged or when scraper blade has been adjusted down as far as possible and does not touch surface or clear properly See Replace Scraper Blade on page 15 EN 17 STORAGE SHORT TERM Never spray unit with high pressure water or store unit outdoors Inspect unit for visible signs of wear breakage or damage and repair as needed Keep all nuts bolts and screws properly tightened and know unit is in safe working condition Store unit in a cool dry protected area Protect bare metal areas with a light coat of oil or anti rust compound LONG TERM Perform all short term storage items Touch up all scratched painted surfaces Fuel System Gasoline left in the fuel system for extended periods without a stabilizer will deteriorate resulting in gum deposits in the system These deposits can damage the carburetor and the fuel hoses filter and tank Prevent deposits from forming in the fuel system during storage by adding a quality fuel stabilizer to the fuel Follow the recommended mix ratio found on the fuel stabilizer container To treat the fuel system for storage 1 Add fuel stabilizer Ariens part number 00592900 according to manufacturer s instructions 2 Run engine for at least 10 minutes after adding stabilizer to allow it to reach the carburetor Never store the engine with fuel in the fuel tank inside of a building with potenti
17. d or CARB regulations that will only function properly when the fuel tank has been filled to the recommended level Overfilling may cause permanent damage to evaporative emissions control system components Filling to the recommended level ensures a vapor gap required to allow for fuel expansion Pay close attention while filling the fuel tank to ensure that the recommended fuel level inside the tank is not exceeded Use a portable gasoline container with an appropriately sized dispensing spout when filling the tank Do not use a funnel or other device that obstructs the view of the tank filling process 5 Replace fuel cap and tighten 6 Clean up any spilled fuel and close fuel and oil door Fuel Stabilizer Gasoline left in the fuel system for extended periods without a stabilizer will deteriorate resulting in gum deposits in the system These deposits can damage the carburetor and the fuel hoses filter and tank Prevent deposits from forming in the fuel system during storage by adding a quality fuel stabilizer to the fuel Follow the recommended mix ratio found on the fuel stabilizer container ENGINE OIL Models 938031 032 033 To check oil level 1 Turn engine off and let cool for at least three minutes 2 Open fuel and oil door Item 22 and remove cap from oil fill 3 Check oil level on dipstick Oil level must be maintained at safe operating level See SPECIFICATIONS on page 20 See Engine Manual for detailed
18. e may require a different octane Consult your Engine Manual Gasoline with up to 10 ethanol gasohol or up to 10 MTBE methyl tertiary butyl ether is acceptable Use of any gasoline other than those approved above may void the engine warranty If gas pumps are not marked for the content of alcohol or ethers check ethanol and MTBE levels with the fuel supplier Do not modify the fuel system to use different fuels Never mix oil and gasoline NOTICE All gasoline is not the same If the engine experiences starting or performance problems after using a new gasoline switch to a different fuel provider or fuel brand IMPORTANT Excessively oxygenated or reformulated fuels fuels blended with alcohols or ethers can damage the fuel system or cause performance problems If any undesirable operating problems occur use a gasoline with a lower percentage of alcohol or ether Fuel Tank To add fuel 1 Turn engine off and let cool for at least three minutes 2 Open fuel and oil door Item 22 and clean fuel cap and surrounding area to prevent moisture and debris from entering fuel tank 3 Remove fuel cap IMPORTANT Refer to Engine Manual for correct type and grade of fuel 4 Fill fuel tank to bottom of filler neck See SPECIFICATIONS on page 20 for fuel tank capacity IMPORTANT Do not overfill This equipment and or its engine may include evaporative emissions control system components required to meet EPA an
19. e proper use of the equipment Know how to stop the unit and disengage the controls quickly Never allow children to operate the equipment Never allow adults to operate the equipment without proper instruction including actual operation Keep the area of operation clear of all persons particularly small children Keep children under watchful care of a responsible adult Be alert and shut off unit if children enter area Exercise caution to avoid slipping or falling especially when operating the snow thrower in reverse Always remove key and or wire from spark plug before assembly maintenance or service Unintentional engine start up can cause death or serious injury Complete a walk around inspection of the unit to understand the unit your work area and all safety decals Preparation Always check overhead and side clearances carefully before operation Always be aware of traffic when operating along streets or curbs Thoroughly inspect the area where the equipment is to be used and remove all pets doormats sleds boards toys wires debris and other foreign objects Disengage all clutches and shift into neutral before starting the engine motor Use only approved extension cords and receptacles when starting units equipped with electric starter Do not connect electric starter cord to any wiring system that is nota three wire grounded system EN 6 Ha
20. e winter garments Avoid loose fitting clothing that can get caught in moving parts Wear footwear that will improve footing on slippery surfaces Never fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner Always place containers on the ground away from your vehicle before filling Wear adequate safety gear including safety glasses with side shields and protective gloves Do not wear loose clothing or jewelry and tie back hair that may get caught in rotating parts Protect eyes face and head from objects that may be thrown from unit Wear appropriate hearing protection Slope Operation Operate the snow thrower on level surfaces Stay off slopes and slippery surfaces Do not clear snow across the face of slopes go up and down Exercise extreme caution when operating on slopes Do not attempt to clear steep slopes Use a slow speed to avoid stops or shifts on slopes Avoid starting or stopping on a slope Do not park unit on a slope unless absolutely necessary When parking on a slope always block the wheels When practical remove gas powered equipment from the truck or trailer and refuel it on the ground If this is not possible then refuel on a trailer with a portable container rather than from a gasoline dispenser nozzle Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete Do not
21. facturer for a replacement manual MODEL AND SERIAL NUMBERS When ordering replacement parts or making service inquiries know the Model and Serial numbers of your unit Numbers are located on the product registration form in the unit literature package They are also printed on a serial number label on your unit see Figure 1 1 Unit Model amp Serial Number Label Figure 1 Record unit model and serial numbers here e Record engine model and serial numbers here PRODUCT REGISTRATION The Ariens dealer should register the product at the time of purchase Registering the product helps the company process warranty claims or contact you with the latest service information Claims meeting requirements during the limited warranty period will be honored whether or not the product registration card is returned with proof of purchase Customer Note If the Dealer does not register your product please fill out sign and return the product registration card to Ariens or go to www ariens com UNAUTHORIZED REPLACEMENT PARTS Use only Ariens replacement parts The replacement of any part on this unit with anything other than an Ariens authorized replacement part may adversely affect the performance durability and safety of this unit and may void the warranty Ariens disclaims liability for any claims or damages whether warranty property damage personal injury or death arising out of t
22. he above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from region to region EN 23 Sno Chore 2013 Ariens Company Ariens 655 West Ryan Street Brillion WI 54110 920 756 4688 Fax 920 756 2407 www ariens com www ariens com au WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm An Ariens Company Brand
23. he use of unauthorized replacement parts NOTE A Parts Manual may be downloaded from www ariens com EN DELIVERY Customer Note If this product was purchased without complete assembly and instruction by a retailer it is your responsibility to Read and understand all instructions in this manual If you do not understand or have difficulty following the instructions contact your nearest Ariens Dealer for assistance NOTE To locate your nearest Ariens Dealer go to www ariens com WARNING Improper assembly or A adjustments can cause serious injury Before Operating Unit 1 Make sure all assembly has been properly completed 2 Understand all Safety Precautions provided in the manuals 3 Review control functions and operation of the unit Do not operate the unit unless all controls function as described in this manual 4 Review recommended maintenance and adjustments 5 Review Limited Warranty policy 6 Fill out a product registration card and return it to Ariens Company or register the product at www ariens com DISCLAIMER Ariens reserves the right to discontinue change and improve its products at any time without notice or obligation to the purchaser The descriptions and specifications contained in this manual were in effect at printing Equipment described within this manual may be optional Some illustrations may not be applicable to your unit EN 3 SAFETY WARNIN
24. in cable and no tension 4 Engage auger control bar to ensure proper operation There should be no excessive tension on cable 5 Lower plastic sleeve _ 3 1 Auger Control Bar 2 Plastic Sleeve 3 Z hook 4 Adjustment Bracket Figure 7 Replace Belt See MAINTENANCE SCHEDULE on page 17 1 Move engine switch Item 16 to OFF position and remove key Allow unit to cool 2 Remove five tapping screws from belt cover and remove belt cover Retain all parts 3 Disconnect extension spring from idler bracket See Figure 8 Extension Spring Drive Pulley Idler Idler Bracket Belt Finger Engine Sheave DPN Figure 8 4 Remove belt from drive pulley idler and engine sheave 5 Install new belt on engine sheave idler and drive pulley Route belt between idler and belt finger on idler bracket 6 Reinstall extension spring 7 Reinstall belt cover Replace Scraper Blade See MAINTENANCE SCHEDULE on page 17 Move engine switch Item 16 to OFF position and remove key Allow unit to cool 2 Tip unit back onto engine guard 3 Remove nuts bolts scraper support and scraper blade Retain hardware Discard scraper blade 4 Check condition of scraper support Replace if worn or damaged 5 Insert scraper support into new scraper blade The D shaped cutout must be on the left drive belt side See Figure 9 _ EN 15 LH Zn Figure 9
25. inor or moderate injury It may also be used to alert against unsafe practices 4 Notice NOTICE Indicates information or procedures that are considered important but not hazard related If not followed property damage could result 5 Important IMPORTANT Indicates general reference information worthy of special attention SAFETY DECALS This snow thrower is capable of crushing or amputating body parts Failure to observe the following safety instructions could result in serious injury or death The safety decals on your machine are visual reminders of the important safety information found in this manual All messages found on your unit must be fully understood and carefully followed Safety decals found on the machine are explained below Always replace missing or damaged safety decals Replacement decal information is in the Parts Manual for your machine Decals can be ordered from your dealer See Figure 2 for safety decal locations EN 4 1 Safety Decal Identification Figure 2 2 Safety Decal Description Danger ROTATING PARTS Keep clear of auger while engine is running e Read Operator s Manual Allow operation only by properly trained adult never children Stop engine and remove ignition key prior to leaving the operator s position for any reason Keep all controls guards and safety devices properly serviced and functional Never direct
26. m 20 5 If engine is cold turn choke Item 15 to CLOSED position NOTICE Do not apply choke to a warm engine 6 Push primer bulb Item 17 twice NOTICE Do not push primer bulb to start a warm engine 7 Slowly pull recoil starter handle Item 5 until engine compression makes pulling difficult Let starter rewind a little and then pull smoothly and quickly to start engine 8 Repeat step 7 as needed 9 Gradually open choke after engine starts IMPORTANT If engine does not start after three attempts see TROUBLESHOOTING on page 19 10 Pull auger control bar Item 2 back to handlebar to start auger release bar to stop auger Start Engine Electric Start Models 938032 033 034 1 Check oil level See Engine Oil on page 12 2 Position discharge chute Item 8 ina safe direction 3 Connect a power cord to power cord recepticle Item 19 and then plug cord into a wall outlet CAUTION Use cord that is minimum of 13 amp 16 Gauge 3 wire grounded plug UL listed CSA Certified Cord must be labeled suitable for outdoor use 4 Move engine switch Item 16 to ON position 5 Open fuel shut off valve Item 20 6 If engine is cold turn choke Item 15 to CLOSED position NOTICE Do not apply choke to a warm engine 7 Push primer bulb Item 17 twice and then press electric start button Item 18 NOTICE Do not push primer bulb to start a warm engine 8 When engine starts disconnect power cord fro
27. m wall outlet then disconnect cord from power cord recepticle IMPORTANT If engine does not start after three attempts see TROUBLESHOOTING on page 19 9 Pull auger control bar Item 2 back to handlebar to start auger release bar to stop auger Discharge Chute Item 8 Models 938030 031 032 034 IMPORTANT Always throw snow in a safe direction away from people and windows To control the discharge of snow 1 Turn discharge chute handle Item 6 in the direction you want to throw snow 2 Loosen wing knob Item 9 and move discharge chute deflector handle Item 7 up or down to control snow throw height 3 Tighten wing knob in desired position If chute becomes frozen and does not turn correctly take unit into warm area until controls are unfrozen CAUTION Do not use chute handle to lift the unit EN 13 Remote Discharge Chute Handle Assembly Item 4 Model 938033 IMPORTANT Always throw snow in a safe direction away from people and windows Move remote discharge chute handle forward or backward to choose the direction to throw snow If chute becomes frozen and does not turn correctly take unit into warm area until controls are unfrozen Stop Engine 1 Release auger control bar Item 2 2 Turn engine switch Item 16 to OFF position 3 If finished with unit close fuel shut off valve Item 20 MAINTENANCE Replace Auger Paddles Replace auger paddles when paddles are worn down to
28. ndle fuel with care it is highly flammable Use an approved fuel container e Never add fuel to a running engine or hot engine Fill fuel tank outdoors with extreme care Never fill fuel tank indoors e Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner Always place containers on the ground away from your vehicle before filling When practical remove gas powered equipment from the truck or trailer and refuel it on the ground If this is not possible then refuel such equipment on a trailer with a portable container rather than from a gasoline dispenser nozzle Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until refueling is complete Do not use a nozzle lock open device Replace gasoline cap securely and wipe up spilled fuel e If fuel is spilled on clothing change clothing immediately Thrown objects can cause injury Check for weak spots on docks ramps or floors Avoid uneven work areas and rough terrain Stay alert for hidden hazards Exercise extreme caution when operating on or crossing gravel drives walks or roads Adjust skid shoes so scraper blade does not contact gravel Stay alert for hidden hazards or traffic After striking a foreign object stop the engine motor remove the wire from the spark plug thoroughly inspect the snow thrower for any damage and repair the damage before restarting and ope
29. on Part No Description 00592900 AR Fuel Stabilizer 4 oz 73801100 Sno Thro Cover Kit 06900533 1 Auger Cable 70707600 Protective Floor Mat 07200627 1 Auger Belt 73800600 Snow Shield Kit 21547400 1 Spark Plug 73800800 Remote Chute Rotation Kit Models 938030 031 032 53802900 1 Auger Paddle 034 Replacement Kit 5 73801000 Maintenance Kit 53803100 1 Scraper Blade Replacement Kit Includes 16 oz 5W 30 engine oil spark 53803800 1 an Arm t Kit plug fuel stabilizer and non stick spray PRAES NENEA Snow Jet SPECIFICATIONS Model Number 938030 938031 938032 938033 938034 Model SS21 SS21 SS21E SS21EC SS21E Recoil Recoil Electric Electric Electric Starter Recoil Recoil Recoil Engine Engine Ariens Engine Model Number AX136 AX208 AX136 Engine Size 136cc 208cc 136cc Max RPM 3600 100 Oil Capacity Pt L 1 0 473 Fuel Tank Capacity Qt L 2 9 2 7 Fuel Octane Rating See Engine Manual Size and Weight Length in cm 54 3 137 9 Width in cm 21 6 54 9 Height in cm 40 9 103 9 hte 87 91 95 97 91 Weight lbs kg 39 46 41 28 43 10 44 00 41 28 EN 20 Sno Thro Sno Tek and RECHA Chore Performing Equipment Limited Warranty COMPANY Ariens Company Ariens warrants to the original purchaser that Ariens Gravely Parker and Countax brand chore performing equipment including Sno Thro and Sno Tek equipment purchased on or after 1 1 2013 will be free from defects
30. ons Items Not Covered by This Warranty Parts that are not genuine Ariens Gravely Parker or Countax service parts are not covered by this warranty and may void the warranty Damages resulting from the installation or use of any part accessory or attachment which is not approved by the Ariens Company for use with product s identified herein are not covered by this warranty The following maintenance service and replacement items are not covered by this warranty unless they are noted in the Limitations section above lubricants spark plugs oil oil filters air filters fuel filters brake linings brake arms brake shoes skid shoes scraper blades shear bolts mower blades mower vanes brushes headlights light bulbs knives cutters and single stage impellers Any misuse alteration improper assembly improper adjustment neglect or accident which requires repair is not covered by this warranty Use of gasoline blends exceeding 10 ethanol voids any and all warranties Products are designed to the specifications in the area that the product was originally distributed Different areas may have significantly different legal and design requirements This warranty is lim ited to the requirements in the area in which the unit was originally distributed Ariens Company does not warrant this product to the requirements of any other area Warranty service is limited to service within the area originally distributed In c
31. ountries other than the United States and Canada contact the Ariens Company dealer for war ranty policies that govern within your country Rights may vary from country to country and within any one country Normal Wear This warranty does not cover repair when normal use has exhausted the useful life of a part such as a high pressure hose spray wand nozzles trigger handle supply hoses quick cou plers gaskets valves pistons pump valve assemblies o rings water and oil seals Special Exclusions on Utility Vehicles The following uses void the warranty terms on Utility Vehicles Warranty Code UA e Renting or leasing the utility vehicle Using the utility vehicle to tow or carry loads in excess of the limits specified in the Owner Operator Manual Modifying the utility vehicle with parts and accessories that are not genuine or authorized Ariens or Gravely parts or accessories Modifying the utility vehicle without express written authorization from Ariens Company e Operating the utility vehicle when it has not been completely and properly assembled and pre delivered by an authorized Gravely dealer Disclaimer Ariens Company may from time to time change the design of its products Nothing contained in this warranty shall be construed as obligating Ariens Company to incorporate such design changes into previously manufactured products nor shall such changes be construed as an admission that previous designs were defective
32. rating the snow thrower If the unit should start to vibrate abnormally stop the engine motor and check immediately for the cause Stop the engine motor whenever you leave the operating position before unclogging the auger impeller housing or discharge guide and when making any repairs adjustments or inspections Adjust the auger impeller housing height to clear gravel or crushed rock surface When leaving the machine unattended disengage the power take off lower the attachment set the parking brake stop the engine and remove the key Never attempt to make any adjustments while the engine motor is running except when specifically recommended by manufacturer Always allow unit and engine to adjust to outdoor temperature before clearing snow When cleaning repairing or inspecting the snow thrower make certain the auger impeller and all moving parts have stopped Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the machine Operation Never leave a running unit unattended Always shut off engine before leaving unit Always remove key to prevent unauthorized use Do not run the engine motor indoors except when starting the engine and for transporting the snow thrower in or out of the building Open the outside doors exhaust fumes are dangerous Do not put hands or feet near or under rotating part
33. s Keep clear of the discharge opening at all times Never operate the snow thrower without proper guards and other safety protective devices in place Moving and or rotating parts can cut off body parts such as fingers or a hand Always keep hands feet and clothing away from all rotating parts during operation Never direct the discharge toward people or areas where property damage can occur from thrown objects Keep children and others away Always keep hands away from all pinch points Do not overload the machine capacity by attempting to clear snow at too fast a rate Slow down and turn corners slowly Do not touch unit parts which might be hot from operation Allow parts to cool before attempting to maintain adjust or service Never operate the machine at high transport speeds on slippery surfaces Look behind and use care when backing EN 7 Do not operate in reverse unless absolutely necessary Always back up slowly and look down and behind before and while backing Maintenance and Storage Do not carry passengers Secure unit so it will not tip over during maintenance Disengage attachment drive when traveling from one work area to another Disengage power to the auger impeller when snow thrower is transported or not in use Before cleaning removing clogs or making any inspections repairs etc disengage clutch es stop unit and engine
34. s 90 Days UA Utility Vehicles 1 Year 1 Year N A Service Replacement Parts 90 Days no labor 90 Days no labor Special Extensions The chart below details special extensions to this warranty Warranty Warranty Code Warranty Exception Period Use Detail Cast Iron Auger 5 Years for all users including SA Gear Case 5 Years A Commercial Cast Iron Auger 5 Years for Consumer use SB Gear Case 5 Years Consumer 1 Year for Commercial Use ji TM SB F AMF 2 Years Consumer 100 first year prorated second year EN 21 Sno Chore 2013 Ariens Company Exceptions and Limitations The chart below details special exceptions to this warranty warranty Warranty Exception warranty Use Detail All Batteries 1 Year All Prorated These components are not covered All Belts Muffler Tires None Commercial when used commercially 2 Warranty is limited to 2 years for Cloth Plastic and 3 gt consumer use 1 year for warranty All ae Bad aa en All code PD Except as noted above Cables g gars these components are covered for defect not for wear SA SB Idlers Maximum All Warranty is limited on idlers to SC 2 Years 2 years for consumer use Engines are covered by engine See Engine 4 manufacturer s warranty Refer to All Engines Manutacturer S All engine manufacturer s warranty y statement Customer Responsibilities Register the product immediately at the time of sale If
35. the dealer does not register the product the customer must complete the product registration card in the literature package and return it to Ariens Company or register the unit online at www ariens com www gravely com www countax com or www parkersweeper com To obtain warranty service the original purchaser must Perform the maintenance and adjustments explained in the Owner s Manual Promptly notify Ariens or an authorized Ariens Gravely Parker or Countax service representative of the need for warranty service Transport the product to and from the place of warranty service at owner s expense Have the warranty service performed by an authorized Ariens Gravely Parker or Countax service representative To Find an Authorized Service Representative In the U S and Canada Use the dealer locator on our websites www ariens com www gravely com Or contact us by mail or by phone In the U S Canada Mexico Caribbean In Europe Asia Africa or Central and South America the Middle East In Australia or New Zealand Ariens Company Ariens Company Countax Ltd Countax House 6 er Rd 655 W Ryan Street Great Haseley Oxfordshire edge ii Hallam Victoria 3803 Australia Brillion WI 54110 OX44 7PF Phone 03 9796 4244 Phone 920 756 4688 Phone 0800 597 7777 1800 335 489 www ariens com www countax com www ariens com au EN 22 Sno Chore 2013 Ariens Company Exclusi
36. use a nozzle lock open device If fuel is spilled on clothing change clothing immediately Properly remove fuel before tipping unit up onto housing so no spills will occur Towing Transporting Always shut off engine remove key and close fuel shut off valve or drain fuel when transporting unit on a truck or trailer Use extra care when loading or unloading unit onto trailer or truck Secure unit chassis to transport vehicle Never secure from rods or linkages that could be damaged Do not transport machine while engine is running Accessories Do not operate near drop offs ditches or embankments Unit can suddenly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Use only Ariens Company recommended attachments that are appropriate to your use and can be used safely in your application Fuel Do not run engine in an enclosed area Always provide good ventilation Fumes from engine exhaust can cause injury or death Fuel is highly flammable and its vapors are explosive Handle with care Use only an approved gasoline container with an appropriately sized dispensing spout No smoking No sparks No flames Always allow engine to cool before servicing Never fill fuel tank when engine is running or hot from operation Never fill or drain fuel tank indoors Replace fuel cap securely and clean up spilled fuel
Download Pdf Manuals
Related Search