Home

Operator & Service Manual Multi-Fruit Juicer

1. Remove splatter shield by sliding upwards off mounting screws Remove lower cup by removing spanner nuts on either side of lower cup A spanner wrench is provided to loosen tighten spanner nuts Place lower cup in waste container Install red protective cap on cutter Red protective cap is provided Grasp juice manifold and orifice tube firmly Remove entire juicing components assembly Grasp orifice tube and pull out of strainer tube Remove strainer tube from inside juice manifold by turning tube counter clockwise and sliding out A spanner wrench is provided to loosen tighten strainer tube Place juicing components into waste container John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech STRIP DOWN DRESS UP Stop machine with cn in Up position Pin id Upper Cup Hold onto upper cup before pulling pin Spanner Nuts Lower Cup CAUTION Knives amp cutter Clear Splatter Shield are very sharp ifol Tool Tighten Juice Manifold Tighten spanner screw amp nuts O Ring securely with tool Nozzle Strainer Tube Tighten strainer tube Loosen Tighten securely with tool Tool SF CAUTION c Hold onto orifice tube when removing or assembling Orifice Tube Groove in slot Figure 2 Juicing Components John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational M
2. John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Juicing Switch Back Switch High Level Switch Cart Switch Figure 13 Interlock Switch Locations Figure 14 Removal of Switch Cover Panel John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 27 FoodTech Troubleshooting Extractor will not start b Check continuity thru all switches Refer to Figure 15b amp 15c c Check continuity across each switch Refer to Figure 15b amp 15c Using a meter check each switch individually Check by opening and closing each cover related to the switch you are checking Replace any defective switches d Some linkage adjustment may be required on juice reservoir float switch e Machines built in 1997 and later have two Schmersal Switches Check alignment of key and switch Adjust if necessary 5 Loose wire connection Check all spade and screw terminals With wires still connected remove cover to motor starter and check for loose wires on D1 and D2 6 Defective under voltage coil Check continuity from terminals D1 to D2 Using a meter check for continuity from terminal D1 to D2 If no continuity is detected replace under voltage coil 7 Defective motor starter Check continuity from terminal 1 to 6 Remove cover on motor starter by grasping both sides and pulling straight out Remove under voltage coil by lift
3. John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Operating Instructions Equipment Check Before plugging the JBT FoodTech Juice Extractor into an electrical outlet the following steps must be performed 1 10 Locate the Citrus Juicer on a level surface This will prevent fruit feed problems Lock both rear casters To lock push down on caster with foot To unlock push again with foot Check waste container Open cart door to verify that waste container is in place A plastic bag may be attached to the hooks above the waste container recommend the Hefty Cinch 30 gallon capacity or equivalent Check juicing components a Twist and pull juice nozzle off b Use key to unlock juicing components cover Open cover and check that juicing components are installed and securely fastened See Figure 1b page 9 Close and lock all access covers There are 4 separate access covers hopper cover juicing components cover cart door cover and back cover NEVER operate extractor unless all covers are in place Replace juice nozzle Make sure juice reservoir is firmly in place Make sure juice reservoir valve is in closed position Check the hopper for foreign objects Remove any foreign objects found in the hopper Make sure floor area around extractor is clean and free of obstructions and water When water is necessary wear appropriate non slip footwea
4. Decal on item 3 5 1 009 450 041 Decal Cleaning Instructions Decal on item 18 6 1 060 00122 Decal Warning Sign Moving Juicer Decal on item 18 7 1 060 00083 Label On Off UL NNP 101 Label on item19 8 1 060 00082 Decal Warning Sign Do Not Open Label on item 17 Exterior 9 009 450 034 01 Decal Base Fruit Recessed Decals on items 1 14 amp 2 15 10 4 009 450 031 Decal Logo Fresh n Squeeze Decals on items 1 1 1 3 amp 2 17 14 3 009 450 033 Decal Roof Fruit Decals on items 3 17 amp 18 13 2 060 00193 01 Bumper Urethane x 26 Lg Bumpers on item 15 14 2 060 00193 03 Bumper Front Urethane x 7 1 2 Lg Bumpers on item 14 15 2 060 00104 B Decal Warning Sign English Spanish 1 inside item 3 1 on item 19 The referenced item numbers in the description above within parenthesis refer to the item numbers on pages 62 63 Figure 47 Decals Warning Labels Bumpers Revised March 2009 to delete item 12 009 450 035 and add item 15 060 00104 B John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 65 n T FoodTech Cover Assembly Parts Stainless Steel 060 01001 F Item Qty Part Number Description 1 060 01036 Hopper Modification 2 1 060 01038 Cover 4 1 060 01055 Cover Door 5 1 060 01044 Spacer Switch Cover 6 1 060 01042 Cover Switch 7 1 060 01041 C
5. FoodTech Rebuildin 7 10 Remove linear shafts With a 3 16 Allen wrench loosen set screws at top and bottom of all three shafts Back screws out at least 1 4 to clear flats on shafts If shafts are stuck use bearing removal puller with 3 8 16 x 2 hex head cap screw to break free shafts Refer to Figure 21 Lift out upper and lower drive arms with linkages still attached Disassemble rod end assemblies from drive and crank arms Note location and numbers of washers and spacers NOTE Screws and rod ends on both crank arms are left hand threads Disassemble rod ends from links Reassemble with new rod ends Refer to Figures 22 and 23 using rod end adjustment bar with the appropriate rod and tooling washer Remember one end is a left handed thread Wrenches required 3 4 7 8 and 15 16 Figure 21 Removal of Linear Shafts with Puller 36 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Rod End Adjustment Bar 5 8 Tooling Washer Figure 22 Assembly of 5 8 Rod Ends 1 2 Tooling Washer Figure 23 Assembly of 1 2 Rod Ends John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 37 JBT Foodlech Rebuilding 11 Remove sleeve bearings from upper and lower drive arms Refer to Figures 24 and 25 Bearings can be pulled out using puller 1 removal slug and short threaded removal rod or can be driven or pressed
6. 6 009 425 020 Description Rod Orifice Clean Out CJ amp MFJ Brush 1 Dia Brush Dish Type Peralkalate Cleaner 750 M Decanter 1 Gal Translucent Key ToolHead 76 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Manual Revisions Page 62 Cover Assembly Parts ABS 060 00118 F Qty Part Number Revisions 5 24 004 401 022 Added S S to description 6 1 060 00110 Changed quantity from 2 to 1 12 1 060 00162 Added Tomlinson to description 13 14 004 401 026 Added S S to description 22 8 004 265 016 Added Blind to description 33 1 006 210 291 Added G R l PSM19 3 16 Dia to description 34 1 009 080 050 Added Hopper Cover to description 35 2 006 200 267 Added 216 to description 36 2 007 143 395 Added CD20MR BK 37 2 004 356 012 Changed quantity from 4 to 2 Changed part from 004 392 175 to 004 356 012 Changed description from Mach Pan Head 8 32 to Socket Head Cap Button Head 10 24 38 4 060 02059 Changed quantity from 1 to 4 39 1 004 401 024 Added Head to description 44 4 004 392 174 Added Spanner Type to description 46 1 060 00121 Added Shear to description 50 4 004 156 041 Changed quantity from 2 to 4 Changed part from 004 136 021 to 004 156 041 Changed description from 8 32 to 10 24 Self locking 51 2 004 385 028 Changed description from 6 to 8 amp added Spanner Type 54 2 060 00104 Added item 54 Page 63 Figur
7. Description 1 1 005 098 727 Rod End Male RH 2 1 004 116 037 Nut Jam Hex 1 2 20 3 1 060 00059 Linkage Orifice Drive 4 1 004 116 038 Nut Jam Hex LH 1 2 20 5 1 005 098 728 Rod End Male LH 1 2 NA Figure 43 Rod End Assembly Orifice Drive Parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 59 n T FoodTech Frame amp Stand Assembly Parts 060 00117 D Item Qty Part Number Description 1 1 060 00101 Frame The frame contains items 1a 1b amp 1c 1a 2 007 120 203 Fitting Grease 1 4 28 Straight Not Shown 1b 2 005 098 731 Bearing 1 x 1 Not Shown 1c 2 005 098 732 Bearing 1 1 4 x 1 1 4 Not Shown 2 1 060 00048 Stand 3 2 009 080 526 Caster Swivel 4 5 5 004 352 392 Screw Hex 3 8 16 x 7 8 6 4 004 111 022 Nut Hex 10 24 S S T 4 004 461 025 Hook 12 2 009 080 527 Caster Rigid 4 13 1 060 00079 Locator Waste Bin 14 16 004 111 040 Nut Hex 5 16 18 S S 15 18 004 816 070 Washer Plain Narrow 5 16 S S 16 22 004 352 315 Screw Cap Hex 5 16 18 x 3 4 60 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Gier FoodTech FRONT HOOKS POINT TO FRONT FRONT REAR Figure 44 Frame amp Stand Assembly Parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 61 n
8. Move juicer on LEVEL surface only Never an inclined surfaces Move only by PULLING on handle NO UTILICE EL EXPRIMIDOR CON LA PUERTA ABIERTA NO INTERFIERA CON EL MECANISMO DE BLOQUEO DE SEGURIDAD DE LA PUERTA EL CONTACTO CON PARTES INTERNAS EN MOVIMIENTO PUEDE CAUSAR LESIONES SEVERAS 0 LA MUERTE DESCONECTAR EL ENCHUFE antes de la limpieza o mantenimiento Safety Instructions Carefully review the following safety instructions Make them a habit when using the JBT FoodTech Juice Extractor 1 If extractor continues to run when any access cover is open interlock switch is defective Turn Juicer off immediately Call for service Prevent unauthorized access to Extractor by locking all covers with supplied key Prevent unauthorized operation of Extractor by placing electrical plug inside cart door NEVER attempt to make any safety device inoperative NEVER operate or perform maintenance or repair work on Extractor when taking any kind of drug or sedative when under the influence of alcohol or when fatigued ALWAYS check adjustment of all nuts bolts and screws after installation repair or periodic maintenance apar John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 5 FoodTech Technical Specifications Fruit size 2 1 2 to 3 3 4 diameter 6 5 cm to 9 5 cm Oranges FL Oranges C Grapefruit FL Hopper capacity Reservoir capacity Wast
9. T FoodTech Cover Assembly Parts ABS 060 00118 F Item Qty 1 1 x o AN MRNA I A OQN AMIDI iN ND mos ano Part Number 060 00044 060 01054 060 00111 060 00045 060 00123 004 401 022 060 00110 060 00071 004 816 060 060 00025 060 00107 060 00036 060 00162 004 401 026 060 00047 060 00035 060 00097 060 00032 060 00033 060 00046 060 00090 015 03939 004 265 016 015 03937 009 092 022 060 00148 060 00120 060 00125 004 816 052 009 210 013 060 00137 060 00140 006 210 291 009 080 050 006 200 267 007 143 395 004 356 012 060 02059 004 401 024 009 654 003 006 270 141 004 385 012 004 392 174 060 00524 060 00121 006 200 489 007 160 029 009 097 002 004 156 041 004 385 028 004 356 013 004 806 030 060 00104 B 009 425 019 060 00073 060 00072 060 00080 Description Cover Drive UL R597016 Shield Splatter Assembly 90 Bend Details See Page 64 Shield Splatter Curved Obsolete Old Style Cover Juice Components UL R597016 Clip Latch Screw Mach Truss Nylok 10 24 x 3 8 Phillips S S Plug Hopper Hole UL R597016 Hinge Cover Front Male Washer Plain Narrow 1 4 S S Reservoir Lid FDA Material Stirrer Reservoir Reservoir Juice FDA Material Faucet Tomlinson Screw Mach Truss 10 24 x 5 8 Phillips S S Cover Door Stand UL R597016 Cover Main Stand U
10. lt N Orr Fooien Operator amp Service Manual Multi Fruit Juicer March 2009 Mutti Fruit Juicer Ger Operator amp Service Manual Multi Fruit Juicer Copyright John Bean Technologies Corporation 2009 JBT FoodTech 400 Fairway Avenue Lakeland FL 33801 863 683 5411 Manual No 060 00203 March 2009 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Safety Information Safety Instructions General Information Operating Instructions Cleaning Instructions Maintenance Periodic Inspection Troubleshooting Rebuilding Kit Parts Listing Juicing Components Listing Hopper Parts Listing Drive Parts Listing Upper Drive Parts Listing Upper Rod End Parts Listing Orifice Drive Parts Listing Orifice Rod End Parts Listing Frame amp Stand Parts Listing Cover ABS Parts Listing Splash Shield Parts Listing Decals Warning Label Listing Cover SS Parts Listing Electrical Parts Listing Electrical Box 115V Parts Listing Electrical Box 220V Parts Listing Motor Assembly Parts Listing Miscellaneous Parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Important Safety Information You can help prevent personal injury and or property damage Please read
11. 1 007 146 010 Nut Tru Seal 1 2 NPT 10 4 004 352 398 Screw Cap Hex 3 8 16 x 1 1 4 S S 11 4 004 806 070 Washer Lock Reg 3 8 S S 13 2 060 00066 Base Motor 14 1 007 661 052 V Ring Seal C R 400161 5 8 110 Volt See Note 1 8 1 060 00093 Motor Wire 110 Volt 60 HZ 9 1 005 617 143 Gearmotor 1HP 60 HZ 12 4 004 816 080 Washer Plain Narrow 3 8 S S 220 Volt See Note 2 8 1 060 00197 Motor Wire 220 Volt 50 HZ 1 005 617 144 Gearmotor 1HP 50 HZ 12 8 004 816 080 Washer Plain Narrow 3 8 S S Note 1 Motor 60 HZ can be wired for 110 Volt or 220 Volt Note 2 Motor 50 HZ can be wired for 110 Volt or 220 Volt Plug must be supplied by customer per country specifications Revised February 2008 to show item 5 cord connector in the down position in Figure 52 Page 75 74 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech AY 15 220V 3 2 8 MOTOR 5 Z WRES INSIDE MOTOR JUNCTION BOX REMOVE FAN SHROUD AND FAN TO INSTALL IT 14 FILL KEYWAY WITH GREASE BOLT TOGETHER amp TAPE i br BOLT TOGETHER amp TAPE a C INSIDE MOTOR JUNCTION BOX 1 i Figure 52 Motor Assembly Parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 75 sr FoodTech Miscellaneous Parts Item Part Number 1 060 00084 B 2 009 080 328 3 009 080 327 4 060 00131 5 009 092 019
12. 1 022 Screw Mach Truss 10 24 x 3 8 SS Phillips 2 2 004 440 004 Screw 6 32 x 3 8 SS Phillips 3 1 060 00076 Switch Plate 6 1 060 00169 Electrical Box Assembly 220v 50 Hz 8 1 060 00141 Switch Bracket 9 1 060 00196 Motor Assembly 220 V 50 Hz 10 1 006 220 004 Terminal 10 Ring End 14 16 Ga 42 1 006 210 290 Prox Switch NC With Gray Leads 13 1 060 00198 Supply Wire 220 V 50 Hz 14 1 060 00525 Cable Back Cover 15 1 060 00525 01 Cable Cart Door 16 1 Plug Depends On Machine Destination Not Shown Machines equipped with high level switches all others have two prox switches on juicing cover 68 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual TO BACK COVER FEED WIRE UNDER MOTOR V JUNCTION BOX AND UP ELECTRICAL BOX TO CART DOOR Figure 49 Electrical Parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 69 n T FoodTech Electrical Box Assembly Parts 115 Volt 060 00168 C Item Qty Part Number Description 1 1 060 00167 Electrical Box Sprecher Schuh M S 2 1 006 040 062 Under volt Release Sprecher Schuh KT3 25 UA 110 3 1 006 190 054 Manual Starter Sprecher Schuh KTA3 25 16A 4 2 007 146 010 Nut Tru Seal 1 2 5 2 007 486 118 Sealing Ring Hubbell 20509001 6 006 060 044 Cord Conn T amp B 2682 1 2 NPT 90 7 1 060 00538 Switch Diaphragm 8 3 006 22
13. 1 066 Terminal Block Curtis 1505 W 9 2 006 060 074 Cord Conn T amp B 2671 3 8 Straight 10 2 007 146 009 Nut Tru Seal 3 8 NPT 11 1 060 00074 12 2 004 397 137 Screw Mach Round 10 24 x 3 8 S S 13 1 060 00075 Box Mounting Plate 14 8 004 397 077 Screw Mach Round 48 32 x 1 2 S S 15 2 060 00096 01 Jumper Wire 12 Ga x 2 1 4 Lg 16 1 060 00537 Frame Diaphragm 17 2 004 352 383 Screw Cap Hex 3 8 16 x 1 2 S S 18 2 004 816 080 Washer Plain Narrow 3 8 S S 19 060 00165 Spacer 20 1 060 00166 Din Rail Motor Starter Mounting 21 1 006 060 077 Cord Conn Straight T amp B 42673 1 2 x 1 2 Dia Cord 22 2 004 816 052 Washer Plain 10 SS 23 2 007 143 396 Strain Relief Fitting 24 2 006 090 245 Plug Snap In Nylon 25 4 004 430 002 Screw 4 x 3 8 Lg Type B S S 26 2 007 143 397 Nut Locking PG11 70 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual SBT FoodTech EI mol mas Figure 50 Electrical Box Assembly Parts 115 Volt John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 71 sr FoodTech Electrical Box Assembly Parts 220 Volt 060 00169 C Item Qty Part Number Description 1 1 060 00167 Electrical Box Sprecher Schuh M S 2 1 006 040 062 Under volt Release Sprecher Schuh KT3 25 UA 110 3 1 006 190 063 Manual Starter Spre
14. 1 8 Dia x 1 4 Alum item 14 only Covers Items 3 14 amp 17 Include the Following Hinges Hinge Cover Hopper Quantity of 1 on Item 17 above Hinge Front Cover Female Quantity of 2 on Item 3 above Hinge Door Stand Quantity of 1 on Item 14 above Machines equipped with high level switches Revised March 2009 to add item 54 060 00104 Decal 62 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Gier FoodTech 00G i Figure 45 Cover Assembly Parts ABS John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 63 FoodTech Splash Shield Assembly Parts 060 01054 Qty Part Number Description 1 060 01025 Shield Clear 2 1 060 01024 Bracket Clear Shield RH 3 1 060 01024 01 Bracket Clear Shield LH 4 4 004 401 022 Screw Mach Truss Nylok Phil 10 24 x 3 8 5 4 004 156 041 Nut Hex S L 10 24 SS LEFT SIDE VIEW FRONT VIEW Figure 46 Splash Shield Assembly Parts 64 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Decals Warning Labels Bumpers Item Qty Part Number Description 1 060 00120 Decal Warning Sign Decals on item 3 14 amp 17 Interior 3 3 060 00121 Decal Warning Sign 1 on item 3 1 on Hopper Side amp 1 Back of Hopper 4 1 009 450 040 Decal Component Assembly Instructions
15. 13 Washer Thrust 1 1 4 14 1 060 00062 Shaft Rotary Drive Upper 15 2 005 576 249 Key Sq 1 4 x 1 1 2 S S 16 1 060 00065 Sprocket Drive Orifice 17 2 005 098 112 Washer Thrust 1 18 005 576 242 Key Sq 1 4 x 1 S S 19 11 004 405 131 Screw Cap Socket 3 8 16 x 3 4 20 1 060 00061 Shaft Rotary Drive Lower 21 1 005 576 061 Key Sq 1 4 x 3 4 S S 22 1 005 576 246 Key Sq 1 4 x 1 1 4 S S 23 1 060 00115 Orifice Drive Arm Assembly Details See Page 58 24 1 060 00063 Shaft Linear Orifice Drive 25 2 004 541 111 Screw Set Socket 5 16 18 x 3 4 S S for Motor Sprocket 54 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual SBT FoodTech EN 9 2822 G 2 UI AI Figure 39 Drive Parts 55 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual n T FoodTech Upper Drive Arm Assembly Parts 060 00116 C Item Qty Part Number Description 1 1 060 00030 Arm Upper Drive this part includes items 1a amp 1b 1a 2 007 120 205 Fitting Grease 1 4 28 45 1b 4 005 098 731 Bearing 1 x 1 2 1 004 226 039 Pin Faspin 3 8 x 1 5 8 3 1 060 00027 Cup Upper 4 1 004 352 661 Screw Cap Hex 5 8 11 x 2 1 2 5 1 060 00057 Lock Rod End 6 1 060 00114 Rod End Assembly Upper Cup Drive Details See Page 57 7 1 060 00078 Screw Upper Cup Crank LH 8 4 004 8
16. 16 120 Washer Plain Narrow 5 8 9 1 060 00009 Crank Upper Cup Drive FAR SIDE TYP Figure 40 Upper Drive Arm Assembly Parts 56 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Rod End Assembly Upper Cup Drive Parts 060 00114 B Item Qty Part Number Description 1 1 005 098 729 Rod End RH 5 8 2 1 004 116 046 Nut Jam Hex 5 8 18 S S 3 1 060 00060 Linkage Cup Drive 4 1 004 116 047 Nut Jam Hex LH 5 8 18 S S 5 1 005 098 730 Rod End LH 5 8 NA Figure 41 Rod End Assembly Upper Cup Drive John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 57 n T FoodTech Orifice Drive Arm Assembly Parts 060 00115 C Item Qty Part Number Description 1 1 060 00058 Orifice Crank Arm 2 2 004 816 100 Washer Plain Narrow 1 2 S S 3 1 004 352 572 Screw Cap Hex LH 4 1 060 00113 Rod End Assembly Orifice Drive Details See page 59 5 1 004 352 571 Screw Cap Hex 1 2 13 x 1 1 2 6 1 060 00011 Arm Orifice Tube Drive this part includes items amp 6b 6a 1 007 120 205 Fitting Grease 1 4 28 45 6b 2 005 098 731 Bearing 1 x 1 7 2 060 00068 Bearing Fruit Lift Figure 42 Orifice Drive Arm Assembly Parts 58 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Rod End Assembly Orifice Drive Parts 060 00113 B Item Qty Part Number
17. 96 Strain Relief Fitting 34 2 006 090 245 Plug Snap In Nylon 35 1 060 00538 Diaphragm Switch 36 4 004 430 002 Screw 4 x 3 8 Lg Type B S S 37 2 007 143 397 Nut Locking PG11 72 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual rer FoodTech Voltage Transformer Elect Box Mounted under Terminal Block eter Sar Terminal Block Release Coil Under Voltage ELECTRICAL DIAGRAM LABEL WIRE ENDS AND COMPONENTS AS SHOWN OOO 2 2 8 OS NN R I I LS O3 9 000 amp 8 5 8 x Pa Oo eOd 3 n 3 eee qoo 0 ili L 7 8 2 HU UU M Figure 51 Electrical Box Assembly Parts 220 Volt John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 73 BT Foodlech Motor Assembly Parts 110Volt 060 00106 C Motor Assembly Parts 220Volt 060 00196 C Item Qty Part Number Description 1 6 006 220 004 Terminal 10 Ring End for 16 14 Ga 2 004 397 137 Screw Mach Round Head 10 24 x 3 8 S S 3 2 004 111 022 Nut Hex 10 24 S S 4 1 006 090 209 Hole Plug Hoffman 050 1 2 5 1 006 060 044 Connector Cord 1 2 NPT 90 6 1 007 486 118 Sealing Ring Hubbell 205 09 001 z
18. Hinges Quantity of 2 on Item 13 Revised February 2008 to correct part number of item 24 Revised March 2009 to add item 33 060 00104 Decal 66 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual SBT FoodTech PARTIAL VIEW BACK COVER AND STAND COVER PARTIAL VIEW BACK COVER u INSIDE DOOR INSIDE DOOR Y qm FRONT MEW FRONT VIEW COVERS REMOVED Figure 48 Cover Assembly Parts Stainless Steel John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 67 n T FoodTech Electrical Parts 060 00034 D Item Qty Part Number Description 110 Volt Parts 1 4 004 401 022 Screw Mach Truss 10 24 x 3 8 SS Phillips 2 2 004 440 004 Screw Tap 466 32 x 3 8 SS Phillips Not Shown 3 1060 00076 Switch Plate 6 1 060 00168 Electrical Box Assembly 115 V 7 1 006 061 003 Wire Nut 74 B Not Shown 8 1 060 00141 Switch Bracket 9 1060 00106 Motor Assembly 10 1 006 220 014 Terminal 10 Ring End 10 12 Ga 11 1 060 00096 03 Wire 20 Ga x 5 Lg White Not Shown 1 006 210 290 Prox Switch NC With Gray Leads 13 1 060 00094 Supply Wire 14 1 060 00527 Cable Back Cover 15 1 060 00527 01 Cable Cart Door 220 Volt Parts 1 4 004 40
19. John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual SBT FoodTech Torque to 25 ft lbs NO Washers Plastic Buttons Both Sides Split This End Torque Cap Screw to 55 ft lbs Torque to 45 ft lbs 2 Washers Figure 28 Completed Assembly of Lower Drive Arm John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Rebuilding 13 14 15 Remove sleeve bearings from main frame Refer to Figures 29 and 30 The outer upper drive shaft bearing can be removed using puller 1 1 4 removal slug and short threaded removal rod The inner bearing can be removed the same way or can be pressed out using driver The lower shaft bearing can be removed the same way except using 1 removal slug New bearings can be installed by compression Figure 31 by using installation pilot installation washer and long threaded installation rod Light coat of Teflon grease can be used on O D of bearings to aid in installation There are thrust washers next to each bearing on the main frame Make sure the old ones have been removed and new ones installed One side of thrust washer is plain metal Silicone this side and glue them to the frames Typical 4 places DO NOT get silicone on surface of any bearing Before reassembling check all shafts for excessive wear replace as necessary Reassemble parts in the reverse order of removal DO NOT forget to p
20. L R597016 Pin Reservoir Holder Cover Hopper UL R597016 Cover Back UL R597016 Cover Switch UL R597016 Spacer Switch Cover Name Plate Rivet Blind Pop 1 8 Dia x 1 4 Grip Patent Plate Container Trash 19 1 2 x 23 1 2 x 13 Decal Install Trash Bag On Hooks Before Juicing Decal Warning Sign Retainer Back Cover Washer Plain 10 S S Float Cyl 1 1 2 D x 2 5 8 Lg Polyp Frame Reservoir Float Pivot Magnet Holder Reservoir Magnet Proximity 1 PSM19 3 16 Dia Bumper Hopper Cover Stem Type 5 8 x 15 16 Switch Safety Schmersal AZ16 Strain Relief Fitting CD20MR BK Screw Socket Head Cap Button Head 10 24 x 3 4 Lg S S Button Threaded Screw Mach Truss Head 10 24 x 1 2 S S Phillips Holder Wire Tie Wire Screw Flat Head 6 32 x 3 4 Lg S S Screw Pan Head 48 32 x 1 2 Lg Spanner Type S S Strip Backing Decal Warning Sign Shear Funnel Adapter with Long Key Grommet 7 16 Dia Hole x 15 16 OD Use on S S Covers Only Cable Tie Holder Nut Hex 10 24 Self Locking S S Screw Flat Head 48 32 x 3 8 Lg Spanner S S Screw Socket Head Cap Button Head 10 24 x 1 Lg S S Washer Lock 10 S S Decal Warning Sign English Spanish Covers Items 3 14 17 amp 18 Include the Following Parts Latch Spring Toolhead Southco 57 10 items 3 14 17 amp 18 Rivet Blind 1 8 Dia x 3 8 Alum Items 3 17 amp 18 Rivet Blind
21. Wipe with a cloth soaked in any pine based cleaner such as Pine Power or Pine Spic amp Span to remove discoloration from plastic covers Rinse thoroughly with sanitizer solution 16 Clean Tomlinson faucet Daily cleaning is crucial to the performance maintenance and sanitation of the faucet Take apart handle assembly and flush with clean water then sanitize 16 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Maintenance Before performing any maintenance DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Do NOT defeat interlock switches After every juice run 1 Check cutter and knives for sharpness Refer to Figure 3 to determine condition of cutter If dull sharpen with a whetstone provided Refer to Figure 4a to sharpen cutter If cutter is severely damaged or rolled over replace cutter a Cutter removal Disassemble juicing components per Figure 1b page 9 Loosen set screw under front knife make sure screw is backed out far enough to clear cutter Cutter should lift out if not tap the cutter lightly from inside the juice manifold with a 1 1 4 dia rod hammer handle Install red protective cap provided onto cutter After red protective cap is installed remove cutter Handle cutter with c
22. ance no bind Rotation Align marks Figure 32 Alignment of Timing Marks 44 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Gier FoodTech Figure 33 Checking for Cup Clearance Ae Figure 34 Adjusting Rod Link Ends John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 45 Rebuilding 18 Remove juicing components and install upper and lower drive splash plates Refer to Figure 35a and 35b Note that chamfer on top front edge of lower splash plate goes up and out Put thin part to the top and flat backside against the wall Also note that groove in upper drive splash plate goes down and in Seal with R T V Silicone allow to dry before running machine Figure 35a Applying Silicone to Upper Splash Plate Figure 35b Applying Silicone to Lower Splash Plate 46 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Motor Siete rea Y Bits I D come tp E dist Em of a logo cor CBO ure onov ema eer S act on 220 Volt Electrico Diagram arom Machines built before 1997 m Tm et 22 T PEET Lr I T Electrical Diogrom muc Machines bu
23. anual FoodTech Prepare cleaning solution 7T Pelican brand Peralkalate is recommended see page 12 Read the product label Follow the manufacturer s mixing directions and safety precautions 8 Immerse all components in cleaning solution Use the blunt end of plastic rod provided to displace any fruit material lodged in the bore of the orifice tube Use pointed end of plastic rod to displace any fruit material lodged in cup fingers 9 Scrub components Use a brush towel or sponge DO NOT use abrasive pads such as Scotch Brite steel wool etc Thoroughly rinse with clean water then thoroughly rinse with sanitizer solution Follow the manufacturer s mixing directions and safety precautions 10 For best results soak strainer tube overnight After soaking overnight rinse the strainer tube thoroughly before using Check that all strainer tube holes are clean Clean strainer tube with a hard spray from a hose while moving orifice tube back and forth in strainer tube Rinse thoroughly with sanitizer solution Allow to air dry 11 If possible hose down juicing area and cover If location prohibits using a hose to clean juicing area and cover ensure waste container is in place Wash down the exposed juicing area and cover with a sponge or spray applicator using the recommended cleaning solution Cover may be rinsed in place or removed by lifting it off the hinges Allow to stand for two minutes before rinsing tho
24. are to avoid direct contact with sharp edge b Cutter installation Align arrows on cutter and juice manifold to seat cutter Make sure cutter is fully seated Tighten set screw DO NOT over tighten John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 17 FoodTech Figure 3 Installation of good cutter Figure 3a Bad cutter REPLACE cutter Figure 3b Cutter that can be sharpened Figure 4a Sharpening Cutter Figure 4b Sharpening knife with Whetstone with Whetstone 18 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Maintenance 2 Check orifice tube for damage Refer to Figure 5 Replace tube when a Chunks are missing from top end b Score marks 1 32 or deeper appear along the length of the tube Figure 5 Severely Damaged Orifice Tube 3 Check for loose or missing nuts and bolts Tighten or replace nuts and bolts as necessary b DO NOT exceed torque ranges specified in Service Manual c ALWAYS use JBT FoodTech recommended spare parts John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Periodic Inspection Perform the following steps after every 3 4 months 1 Test all access cover interlock switches Extractor should stop automatically when any access cover is opened Individually open and close the four access covers hopper j
25. c inspection John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 31 FoodTech Rebuilding It is best to replace all bearings at the same time DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Do NOT defeat interlock switches Step by Step instructions for replacing all bearings and rod ends 1 Remove all juicing components 2 Lift juicing component cover off its hinges Refer to Figure 1 Remove back cover 1 4 turn lock at top pull cover out by using finger hole to the left of the lock then lift and pull using finger hole of bottom DO NOT loosen any screws Remove drive cover one screw on top and two on the side DO NOT loosen lower two screws 3 Remove upper and lower drive splash plates in juicing area Refer to Figure 16 Use knife to cut away Silicone from plastic splash plates and drive arms If necessary use hand crank adapter on motor sprocket with 1 2 drive ratchet to rotate machine into position to pull off splash plates Refer to Figure 17 and Figure 36 item 12 32 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Upper Drive Splash Plate Drive Access Hole Lower Drive Splash Plate Figure 16 Front View of Juicer Upper Linear Shaft Upper Rotary Sha
26. cher Schuh KtTA3 25 10A 4 2 007 146 010 Nut Tru Seal 1 2 NPT 5 2 007 486 118 Sealing Ring Hubbell 20509001 6 1 006 060 044 Cord Conn 2682 1 2 90 7 1 060 00537 Frame Diaphragm 8 1 006 221 079 Terminal Block Phoenix G5 6 9 2 006 060 074 Cord Connector 2671 3 8 Straight 10 2 007 146 009 Nut Tru Seal 3 8 NPT 11 1 060 00074 Panel 12 2 004 397 137 Screw Mach Round 10 24 x 3 8 S S 13 1 060 00075 Box Mounting Plate 14 6 004 397 077 Screw Mach Round 48 32 x 1 2 S S 15 1 060 00096 03 Jumper Wire 20 Ga x 5 Lg 16 1 060 00096 02 Jumper Wire 12 Ga x 10 Lg 17 2 004 352 383 Screw Cap Hex 3 8 16 x 1 2 S S 18 2 004 816 080 Washer Plain Narrow 3 8 S S 19 1 006 240 027 Transformer Signal DP241 4 120 20 6 006 221 081 Terminal Fully Insul Panduit DNF18 206FIB C 21 2 060 00170 Stand Off Terminal Strip 22 2 004 397 104 Screw Mach Round 8 32 x 1 1 4 Lg S S 23 1 004 397 072 Screw Mach Round 8 32 x 1 4 Lg S S 24 E 004 816 052 Washer Plain 10 S S 25 1 060 00165 Spacer 26 1 060 00166 Din Rail Motor Starter Mounting 27 1 006 060 077 Cord Conn Straight T amp B 42673 1 2 NPT x 1 2 Dia Cord 28 A R 009 455 004 Marker Pins Phoenix Set 10 Thru 15 29 1 060 00194 Mounting Pad Terminal Block 30 004 440 001 Screw Mach Round Head 4 40 x 3 4 Lg S S 31 3 060 00096 07 Jumper Wire 20 Ga x 10 Lg 32 Wire Markers 33 2 007 143 3
27. e 45 Cover Assembly Parts ABS Added balloon for item 38 Added balloon for item 54 Page 65 Decals Warning Labels Bumpers and Figure 47 Deleted item 12 and added item 15 on both parts list and Figure 47 Page 66 Cover Assembly Parts Stainless Steel 060 01001 F Added item 33 060 00104 B Decal Page 67 Figure 48 Added balloon for item 33 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 77
28. e container capacity Speed 20 to 60 gallons hour 75 to 225 liters hour 125 to 50 count 138 to 48 count 56 to 48 count 40 Ib 1 carton 18 kg 3 1 2 gal 1 carton 13 2 liters 40 Ib of peel 2 cartons 18 kg 20 fruit minute Electrical Specifications 115V 60HZ Single Phase 20 AMP Service 12 GA wire up to 100 ft from main breaker panel or 10 GA wire up to 200 ft from main breaker panel 220 VAC 50 HZ Single Phase 16 AMP Service Shipping Specifications Machine With Stand Height 67 Width 27 Depth 32 Weight 535 Ibs Patents 170 cm 69 cm 81 cm 243 kg U S Patents 4905586 and 4922814 amp Patents Pending John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech General Information The JBT FoodTech Juice Extractor is designed to provide years of dependable service It uses a unique patented design to extract every available amount of juice from the fruit with the least amount of peel oil The peel is completely separated from the juice and juice sacs before being compressed and strained The machine will juice all types of citrus oranges grapefruit lemons limes tangerines etc without changing or adjusting parts In fact different varieties and sizes of fruit can be juiced to create various fruit juice blends Clean up is simple requiring disassembly of only five part
29. ft Lower Drive Assembly Lower Drive Crank Arm Lower Rotary Shaft Hand Crank Adapter with Dog Pt Set Screw Figure 17 Back View of Juicer Upper Cup Drive Assembly Upper Drive Crank Arm John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 33 FoodTech Rebuilding 4 From 3 inch square access hole on side of machine use a 5 16 Allen wrench to loosen socket head cap screw on crank arm for upper cup drive Use hand crank adapter to rotate as necessary Use a 3 16 Allen wrench to loosen set screw on keyway Back screws out at least 1 4 to clear flats on shafts Refer to Figure 18 From the back repeat above steps on crank arm for lower drive Refer to Figure 19 5 Rotate drive so upper cup drive is in the down position Remove chain spring clip type master link Be careful drive arms may move as chain is removed 6 Remove sprockets with shafts still connected Pull or pry on large diameter upper drive sprocket repeat for lower drive sprocket Refer to Figure 20 Figure 18 Using Allen Wrench to Loosen Upper Cup Crank Arm 34 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual BT Foodlech Figure 19 Loosening Lower Crank Arm Note number of thrust washers Figure 20 Sprockets with Shaft being Removed John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 35
30. ilt in 1997 and later John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual On T FoodTech Rebuild Tooling Kit amp Spare Parts Kits Item Part Number Description 1 060 00180 B Tool Bearing Installation Pilot 2 060 00181 B Tool Bearing Installation Washer 3 060 00182 B Tool Bearing Puller 4 060 00183 B Tool Bearing Removal Slug 1 5 060 00184 B Tool Bearing Removal Slug 1 1 4 6 060 00185 B Tool Bearing Removal Driver 060 00186 B Tool Bearing Installation Rod 8 060 00187 B Tool Bearing Removal Rod 9 060 00188 B Tool Washer Rod End 1 2 10 060 00189 B Tool Washer Rod End 5 8 11 060 00190 B Tool Rod End Adjust Bar 12 060 00191 B Tool Adapter Hand Crank 13 004 350 648 Screw Cap Hex 5 8 11 x 1 1 2 C G 14 004 350 571 Screw Cap Hex 1 2 13 x 1 1 2 Full Thread C G 15 004 110 063 Nut Hex 1 2 13 Grade 8 Steel 16 004 815 100 Washer Plain Narrow 1 2 C G 17 00 4815 080 Washer Plain Narrow 3 8 C G 18 004 350 407 Screw Cap Hex 3 8 16 x 2 C G 19 004 410 046 Screw Set Square Head Dog Pt 3 8 16 x 3 4 20 009 998 004 Bit Spanner Insert 48 1 4 Hex Not Pictured 060 00202 Kit Tool CJ amp MFJ Includes above Items 1 20 Other Multi Fruit Juicer Kits 060 00201 Kit Bearing Overhaul 060 00215 Kit Complete Overhaul 060 00200 Kit Spare Parts Cleaning Components amp Other Parts 060 00084 Rod Orifice Clean Out 009 080 326 Brush 1 1 16
31. ing and pulling out Push ON button Button should stay in down position Using a meter check for continuity from terminal 1 to 6 If no continuity is detected or ON button does not stay down replace motor starter 8 Defective motor If ON button on starter stayed in when trying to start machine and motor did not start or rotate replace entire gear motor If there is a humming noise the capacitor needs to be replaced To replace capacitor remove long cylindrical cover on motor Reseal motor cover with RTV Silicone 28 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Figure 15a Sprecher Schuh Electrical Box Electrical Diagram Sprecher Schuh Figure 15b lt 3 se 2 E T MACHINES THAT DON T HAVE LEVEL SWITCH See Next Page For Schmersal Switch Diagram John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 29 On T FoodTech fi 7 fay Schmersol switch Electrical Diogrom 115 Volt 60 Hz with two Schmersol switches mar 1997 ond loter oe wa Figure 15c See Page 47 for 220V Diagrams 30 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Troubleshooting Machine starts but shuts off 1 Building circuit breaker is not rated for 20 Amps 2 Exten
32. ls See Pages 66 67 Lift Fruit FDA Material Guide Fruit FDA Grade Cup Lower Spanner Nut Stud Cup Lower Cutter With Screw Screw Mach Round 4 40 x 3 16 S S Manifold Juice O Ring Nozzle 1 x 1 1 8 x 1 16 Screw Cap Hex 3 8 16 x 1 1 4 S S Nozzle Straight Plastic Nozzle SS 90 Bend Jamba Bearing Fruit Lift Tube Strainer 033 Tube Strainer 040 Tube Strainer 055 Plate Orifice Drive FDA Grade Tube Orifice Tool Wrench Not Shown Cap Cover for Cutter Not Shown Warning Label Shear Hopper Pin Manifold Locator Nut Acorn 3 8 16 SS Washer Lock 3 8 SS Parts for Small Fruit Restrictor Fruit Hole Small Fruit Guide Block Small Fruit Not Shown Restrictor Hopper Side Small Fruit Not Shown Restrictor Juicing Side Small Fruit Not Shown 50 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Figure 37a Juicing Parts gee M o S 7 SMALL FRUIT INSERT PART 060 00088 B T PREVENTS DOUBLE FEEDING OF SMALL FRUIT DOWN 2 DIAMETER SLIPS OVER UPPER HALF OF HOLE FLANGE IN FRUIT LIFT e REMOVE WHEN RUNNING LARGER FRUIT e USING SPANNER WRENCH IN HOLES WILL AID IN INSTALLATION amp REMOVAL LOWER CUP REF UPPER CUP NOT SHOWN Figure 37b Small Fruit Adapter John Bean Technologies Corporation M
33. n cap screws 8 Checkto make sure two plastic bearing buttons have been installed on bottom face of fruit lift Refer to Figure 12 Figure 10 Fruit Lift Alignment 24 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Figure 11 Fruit Lift Bolts Figure 12 Fruit Lift Plastic Bearings John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 25 FoodTech Troubleshooting Extractor will not start Extractor is not plugged into electrical outlet Building circuit breaker has tripped All covers are not completely closed Defective interlock switch enn Machines built before 1997 have five interlock switches Refer to Figure 13 1 Hopper cover 1 Back cover 1 Cart door cover 1 Juicing Component cover 1 High Level Switch Machines built in 1997 and later have two Schmersal Switches Refer to Figure 15c DISCONNECT ELECTRICAL PLUG before cleaning or maintenance Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Do NOT defeat interlock switches a Remove the large cover protecting electrical box and motor Refer to Figure 14 Loosen three screws in juicing area Remove three screws on the right side Remove electrical box cover with on off switch Two on Machines without High Level Switch 26
34. out using driver New bearings can be installed by compression Figure 26 by using installation pilot installation washer and long threaded installation rod or just use installation pilot and press bearings into place Light coat of Teflon amp grease can be used on O D of bearings Bearing Removal Slug 1 Inside Bearing Removal Puller Bearing Removal Rod 1 2 13 Nut Bearing Removal Driver Figure 24 Removing Bearings from Upper Drive Arm 38 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual SBT FoodTech Figure 25 Removing Bearings from Lower Drive Arm Bearing Installation Washer Bearing Installation Rod Bearing Installation Pilot Figure 26 Installation of Bearings into Drive Arms John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 39 BT Foodlech Rebuilding 12 Reassemble rod end assemblies to drive arms again making sure left hand threaded ends are on the crank arms Refer to Figures 27 and 28 Use Loctite 242 on all fasteners Tighten to torques as shown Make sure rod end lock spacer is installed on rod end in upper drive arm Make sure plastic bearing buttons are installed on each side of lower drive arm 2 Washi Torque to 60 ft Ibs 2 Washers Rod End Lock Spacer Torque to 90 ft Ibs 2 Washers Torque Cap Screw to 55 ft Ibs Figure 27 Completed Assembly of Upper Cup Drive Arm 40
35. over Drive S S 8 1 060 01040 Cover Back 9 1 02060 01025 Shield Clear 10 1 060 01024 Bracket R H 11 1 060 01024 01 Bracket L H 12 1 060 01060 Cover Hopper 13 1 060 01061 Cover Juice Assembly S S 14 1 009 425 019 Latch Spring Toolhead 15 2 060 00120 Sign Warning Cover Switches 16 1 009 450 040 Assembly Instructions 17 1 009 450 041 Cleaning Instructions 18 11 004 401 022 Screw Mach Truss Nylok 10 24 x 3 8 Phillips 19 4 004 156 041 Nut S L 10 24 5 5 21 1 060 00122 Sign Warning Moving Juicer 22 1 015 03937 Patent Plate 23 1 015 03944 Name Plate 24 10 004 260 017 Rivet Pop 1 8 Dia x 1 8 Grip 25 6 060 00125 Retainer Back Cover 26 1 009 097 002 Cable Tie Holder 28 1 060 05058 Key Ring amp Key Not Shown 29 1 060 00083 Label On Off 30 1060 00121 Warning Label Shear Hopper 31 2 060 00097 Pin Reservoir Holder 32 1 009 080 050 Bumper Stem Type 5 8 x 15 16 33 1 060 00104 B Decal Warning Sign English Spanish Covers Items 4 12 amp 13 Include the Following Parts 3 009 425 019 Latch Spring Toolhead Southco 57 10 Items 4 12 amp 13 4 Rivet Blind 1 8 Dia x 3 8 Alum Items 12 amp 13 2 004 265 017 Rivet Pop 1 8 Dia x 1 8 Grip Item 4 only Covers Items 4 12 amp 13 Include the Following Hinges 1 060 00080 Hinge Door Stand Hinge Quantity of 1 on Item 4 1 060 00073 Hinge Cover Hopper Hinge Quantity of 1 on Item 12 2 060 00072 Hinge Front Cover Female
36. per bump button Refer to Figure 9b Replace bump button if it has worn to less than 1 8 high To locate hopper bump button remove hopper a Hopper removal Fruit lift upper cup drive must be in down position Remove two spanner screws using spanner wrench Remove hopper If hopper does not lift out see Troubleshooting page 26 item a to remove electrical switch cover b Hopper installation DO NOT over tighten spanner screws Hopper is designed to be loose Hopper must be free to bump during each cycle to prevent fruit bridging 22 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Filler Plug Level Plug Drain Plug Figure 8 Checking Oil Level in Gearbox Figure 9a Hopper Removal Figure 9b Bump Button Installation John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 23 nr FoodTech Periodic Inspection 7 Check alignment of fruit lift Refer to Figure 10 Fruit lift agitator dividers must align with the middle of slots in bottom of hopper a Fruit lift adjustment Refer to Figure 11 Loosen the two cap screws attaching the fruit lift to upper cup drive arm Adjust fruit lift Tighten cap screws b Fruit lift repair If fruit lift is damaged bent but not broken it can be removed and straightened Remove hopper before fruit lift Straighten fruit lift Reinstall fruit lift with Loctite 242 o
37. r John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Operating Instructions Juicing 1 Turnon Extractor Push the ON OFF button to ON position 2 Fruit may be fed into Extractor one at a time Single Feed or in bulk a Single Feed Remove hopper single feed hole cover Twist and pull cover to remove Drop fruit individually down single feed chute through hole in hopper cover DO NOT overload chute or fruit will accidentally be double fed b Bulk Feed Unlock and open the hopper cover Dump up to one carton 40 Ibs of fruit into the hopper Fruit may be divided between the carton and carton lid for ease of lifting 3 DO NOT use the single feed chute when hopper is full Fruit will accidentally be double fed 4 Turn off Extractor Push the ON OFF Switch to the OFF position 5 Stir juice Use stirrer handle to stir juice in reservoir before filling containers 6 Fill containers Place container under juice reservoir valve Open valve by turning lever until container is full 7 Clean Extractor If finished juicing clean Extractor as soon as possible See next page for cleaning instructions John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 11 n T FoodTech Cleaning Instructions ALWAYS follow cleaning and maintenance schedules in this manual to prevent equipment damage Clean Ext
38. ractor as soon as possible for juicing Use a soft towel or sponge to wipe equipment parts DO NOT use abrasive pads such as Scotch Brite steel wool etc The recommended cleaner is Pelican brand Peralkalate Peralkalate is a low foaming alkaline equipment cleaner It is safe on aluminum 100 water soluble and free rinsing Peralkalate has been especially formulated for cleaning food processing equipment and is USDA accepted Follow instructions on cleaner label for dilution 1 Turn off Extractor with Juicing Component cups separated 2 DISCONNECT ELECTRICAL PLUG DISCONNECT ELECTRICAL PLUG hefore cleaning or maintenance Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Do NOT defeat interlock switches 3 Pull Extractor to clean up area if one is available Juicer weights over 250 Ibs Move juicer on LEVEL surface only Never on inclined surfaces Move only by PULLING on handle 4 Brush all loose peel into waste container or bag 5 Empty and rinse waste container John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Cleaning Instructions 6 Remove juicing components a Cups should be separated Extractor should have been turned off with cups in the separated position Grasp upper cup and pull out pin just above it Place upper cup in waste container
39. roughly with water 12 Re assemble juicing components Start by re assembling strainer tube into juice manifold Tighten with spanner wrench Insert orifice tube into bottom of strainer tube Mount juice manifold assembly onto locating pins with orifice tube notch engaging lower drive Tighten spanner screw with spanner wrench Remove red protective cap from cutter Install lower cup and tighten spanner nuts with spanner wrench Install upper cup by slipping pin into stem hole Install splatter shield Refer to Figure 2 page 14 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 15 FoodTech 13 As necessary hose down drive area Remove back cover Turn lock at top 1 4 counter clockwise Pull cover out by using finger hole left of lock then lift and pull cover using finger hole on bottom DO NOT loosen any screws Open hopper cover Open cart door cover Hose down all exposed areas Extractor is water resistant DO NOT use any cleanser in drive area 14 Remove wax build up as needed Cups hopper and other parts may acquire a build up of wax over time a Soak cups for five minutes in an ammonia cleaning solution Rinse thoroughly with sanitizer solution b Wipe hopper and other parts with a cloth soaked in ammonia cleaning solution 15 Remove orange discoloration as needed Equipment may exhibit some build up or orange coloration over time Peralkalate Solution should remove this
40. s All waste material peel membranes and seeds is collected in a disposable garbage bag for easy removal and disposal The Juice Extractor is solidly built using heavy duty components in all assemblies including the drive It is simple to operate and uses a minimal number of parts ALWAYS follow cleaning and maintenance schedules in this manual to prevent equipment damage For a quick introduction to the JBT FoodTech Juice Extractor please review the diagram on the next page John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual Gier FoodTech Single Feed Hole EEE w a Va turn lock Back Cover sm Hopper Cover Hopper Drive Cover On Off Switch Ya turn lock Juice Components Cover Stirrer Handle Juice Nozzle Juice Reservoir Juice Reservoir Valve Cart Cover Va turn lock Cart Door Figure 1a JBT FoodTech Juicer Extractor 8 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Pull Pin Upper Cup Fruit Lift Upper Drive Sp lash Plate Fruit Guide Spanner Nut 2 Juice Manifold Lower Cup Strainer Tube Spanner Screw k Orifice Tube Lower Drive Splash Plate Note Groove part of Orifice Tube in slot Figure 1b Juicing Components Assembly Garbage Bag Hooks Cleaning Tools Storage Pan Spanner Wrench aste Container Figure 1c Inside Cart Door
41. sion cord or wiring is too long Shorten extension cord or use heavier gauge wire See page 6 Electrical Specifications 3 All covers not completely closed including cart Extractor may be flexing when squeezing fruit causing switch to open Make sure all latches are completely locked 4 Amperage setting on motor starter on machine set too low See page 26 item a under Extractor will not start for removing covers Dial next to OFF button should be set at 14 En Extractor stalls trying to squeeze a fruit 1 Fruit has part of stem on it Turn off Extractor Remove fruit from Extractor and restart 2 Peelis too thick Turn off Extractor Remove fruit from Extractor and restart 3 Cutter is damaged Sharpen or replace cutter as specified on under maintenance RU TT TT Install red protective cap onto cutter After red protective cap is installed remove cutter Handle cutter with care to avoid direct contact with sharp edge Extractor runs with covers open or off 1 Defective interlock switch Replace immediately See page 26 item a under Extractor will not start for removing covers Extractor emits a squealing sound during operation 1 Lubricate grease fittings on machine If noise continues rod end or bearing is defective see Rebuilding section to replace bearings Scraping noise coming from hopper area 1 Fruit lift mechanism is dragging on hopper See page 24 item 7 under periodi
42. this manual carefully before operating the JBT FoodTech Extractor DO NOT attempt any operation until you understand exactly how the machine functions If uncertainty remains after studying this manual please contact John Bean Technologies Corporation JBT FoodTech 400 Fairway Avenue Lakeland FL 33801 863 683 5411 or The local JBT FoodTech service representative in your country We re here to help With proper handling the JBT FoodTech Juice Extractor will provide safe efficient and convenient service for years to come 4 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Safety Labels The safety labels shown below appear on the Juice Extractor They provide essential instructions on how to avoid possible hazards Please for your safety FOLLOW THOSE INSTRUCTIONS AT ALL TIMES Should the Juicer safety labels become damaged or unreadable contact JBT FoodTech for replacement labels DISCONNECT ELECTRICAL PLUG hefore cleaning or maintenance gt Juicer should NOT run when any cover is open Contact with internal moving parts could cause severe injury or death Do NOT defeat interlock switches DO NOT run Juicer with door open DO NOT defeat safety interlock on door CONTACT WITH INTERNAL MOVING PARTS COULD CAUSE SEVERE INJURY OR DEATH DISCONNECT ELECTRICAL PLUG before cleaning or maintenance A Juicer weights over 250 Ibs
43. uice components cart and back If extractor continues to run when any access cover is opened the interlock switch is defective Stop the extractor and replace immediately See Trouble Shooting Section 2 Check all fasteners for tightness Check especially on the Sprockets Crank Arms Fruit Lift and Hopper 3 Check chain for tightness Refer to Figure 6 Chain should have 1 4 inch maximum slack on top side To adjust see Figure 7 loosen the four bolts holding the gearbox base to frame move motor gearbox to the correct adjustment If necessary use a small board to pry between frame and motor 4 Check chain and sprockets for rust If rust appears coat chain and sprockets with a small amount of grease 20 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech Figure 6 Checking Chain Slack Figure 7 Loosening Bolts on Base of Motor and Prying Motor John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 21 FoodTech Periodic Inspection 5 Check oil level in gearbox Refer To Figure 8 If Extractor has been laid on its side for any reason i e during shipping or if there is any evidence of oil leak check gearbox for proper oil level Remove back cover Oil level plug is located on the left side of gearbox Filler plug is located on the top of the gearbox Use S A E 40W oil only 6 Check hop
44. ulti Fruit Juicer Service amp Operational Manual 51 n T FoodTech Hopper Assembly Parts 060 00043 F Item Qty Part Number Description 1 1 060 00042 Hopper 2 1 060 00019 Trough 3 1 060 00018 Divider 4 7 004 260 018 Rivet Blind 3 16 x 5 16 Grip 7 16 Ig S S 5 1 060 00089 Button Hopper Bump 6 2 004 260 015 Rivet Blind 3 16 x 1 4 Grip 13 32 Ig S S ti rum itd H i 1 I I E lI 1 III I INI 1 INI 1 lI LL HEADS AS SHOWN Figure 38 Hopper Assembly Parts 52 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 53 n T FoodTech Drive Parts 060 00103 F Item Qty Part Number Description 1 1 005 220 145 Chain 460 x 60 3 4 Lg 81 Links 2 1 005 221 291 Link Connecting For 60 3 1 060 00034 Electrical Assembly Details See Pages 68 69 4 1 005 806 227 Sprocket 60B14 Set Screw for motor 5 4 004 352 404 Screw Cap Hex 3 8 16 x 1 3 4 6 4 004 806 070 Washer Lock Reg 3 8 S S 7 4 004 816 080 Washer Plain Narrow 3 8 S S 8 1 060 00117 Frame amp Stand Assembly Details See Pages 60 61 9 2 060 00064 Shaft Linear Upper 10 1 060 00116 Upper Drive Arm Assembly Details See Page 56 11 1 060 00010 U C Drive Arm Sprocket Upper Cup 12 3 004 355 116 Screw Cap Socket 3 8 16 x 2 13 2 005 098 1
45. ut keys back into crank arms On both crank arms be sure to tighten socket head cap screw first And then the set screw Tighten fasteners to torques shown Lubricate all grease fittings if provided Figure 29 Removing Bearing from Lower Rotary Drive 42 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual IBT Foodtech Bearing Removal Rod Bearing Removal Slug 1 1 4 Figure 30 Removing Bearing from Upper Rotary Drive k NE Figure 31 Installation of Bearings and Thrust Washers Installation Pilot Installation Washer Bearing Installation Rod John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 43 Gier FoodTech Rebuilding 16 17 Before installing chain align timing marks as shown Refer to Figure 32 This is critical to operation of the machine Adjust chain as shown in Maintenance section To check to see if upper cup crank rod end link needs to be adjusted install juice manifold upper and lower cup Refer to Figure 33 Using hand crank adapter gently rotate until upper cup drive is in the full down position DO NOT force it if it appears to be binding readjust rod end link Figure 34 If it rotates freely past bottom position check for too much clearance In the full down position remove pull pin from upper cup Cup should not drop down if it does readjust rod end link Cups should just meet no clear
46. x 8 060 00131 Peralkalate Cleaner 750 M 009 710 031 Stone Sharpening 003 460 053 Lubricant W Teflon 3 Oz Tube 003 460 057 Lubricant W Teflon 14 Oz Can 003 015 905 Silicone White 3 Oz Tube 48 John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual FoodTech 14 92s 15 1 00 1 00009 Figure 36 Rebuild Kit John Bean Technologies Corporation Multi Fruit Juicer Service amp Operational Manual 49 n T FoodTech Juicing Parts 060 00099 F Item Qty Part Number 1 1 060 00103 2 2 004 352 410 3 2 004 816 080 4 1 060 00056 5 3 060 00051 6 1 060 00043 6 1 060 00043 01 7 1 060 00118 T 1 060 01001 8 1 060 00038 9 1 060 00028 10 1 060 00004 Tit 2 060 00098 12 2 060 00109 13 1 060 00225 14 1 004 406 003 15 1 060 00108 16 1 007 486 119 17 2 004 352 398 18 1 060 00022 18a 1 060 01059 19 2 060 00068 20 1 060 00086 20a 1 060 00208 20b 1 060 00230 21 1 060 00055 22 1 060 00008 1 26 1 060 00077 30 1 009 092 018 31 1 060 00121 32 2 060 00192 33 2 004 100 018 34 2 004 806 070 1 060 00088 2 060 01069 1 060 01066 1 060 01067 Description Drive Assembly Details See Pages 54 55 Screw Cap Hex 3 8 16 x 2 1 4 S S Washer Plain Narrow 3 8 S S U C Drive Cover Plate Spanner Screw Hopper Assembly ABS Hopper Assembly SS Cover Assembly ABS Details See Pages 62 63 Cover Assembly Stainless Steel Detai

Operator & Service Manual Multi-Fruit Juicer

Contents

Download Pdf Manuals

Related Search

Related Contents

Operator &amp; Service Manual Multi-Fruit Juicer

Contents

Download Pdf Manuals

Related Search

Related Contents

Operator & Service Manual Multi-Fruit Juicer