Download926.1 kb
Contents
1. Quick Reset d Tap Yes 2 If necessary adjust the position of the image on the screen a Tap the Lens Adjust P __ icon on the Main screen 1 b Tap the Left or Right arrow icons in the Offset area to move the image right or left a c Tap the Up or Down up or down d Tap OK arrow icons in the Offset area to move the image 3 Install the shroud if removed Technical Support North and South America 1 800 221 8025 or tech support christiedigital com Europe Middle East and Africa 44 0 1189 778111 or techsupport emea christiedigital com Asia Pacific tech asia christiedigital com Motor Upgrade Kit Update Service Bulletin 11 020 200262 01 Rev 1 01 20142. mount 4 Connect the 2 focus motor connectors Motor Upgrade Kit Update Service Bulletin 6 020 200262 01 Rev 1 01 2014 CHRISTIE 6 Connect the 2 vertical motor connectors Motor Upgrade Kit Update Service Bulletin 020 200262 01 Rev 1 01 2014 CHAISTIE Install the Zoom Motor Kit 1 Rotate the lens zoom ring until it hits the stop closest to the zoom sensor flag 2 Remove the 2 screws securing the zoom motor cover to the replacement zoom motor assembly 3 Remove and set aside the zoom motor cover and screws M a PT NE SE HK ee 8H _ Lt Nr j L T I 4 Hold the zoom motor assembly in position and slide the zoom motor clamp downward onto the lens and over the base of the zoom motor assembly 5 Position the zoom motor clamp locking screw next to the motor control assembly away from the lens locking lever The image shows the zoom motor cover in position to assist with locating the locking screw _ 6 Tighten the zoom motor clamp locking screw to secure the zoom motor assembly to the lens Allow enough movement for adjustments Motor Upgrade Kit Update Service Bulletin 020 200262 01 Rev 1 01 2014 CHRISTIE 7 Verify the center of the zoom motor assembly sensor A is centered over the zoom sensor flag B on the zoom gear ring To adjust the spacing between the zoom motor assembly sensor and the
3. procedures for correcting the Motor Upgrade Kit functionality issue The illustrations used in the procedures show a Christie CP4230 projector For instructions that are specific to your projector model see the projector Service Manual Back Up Projector Settings Service permissions are required to complete this procedure This procedure is not required if Solaria Main Software v4 0 or later is installed The backup is only required if the software upgrade fails To restore projector settings see the projector User Manual 1 Insert a USB flash drive into the USB port on the side of the projector touch panel controller TPC On the TPC tap Menu gt Service Setup gt File Management 3 Tap Backup Remove the Lens Turn the lamp off and allow it to cool for a minimum of 15 minutes Turn the projector off and disconnect it from AC power 1 2 3 Remove the front shroud if installed A Disconnect the 2 zoom motor connectors A Za Y J array a a ey mer i EEDIT iiA py ay a F H PETETA Motor Upgrade Kit Update Service Bulletin 2 020 200262 01 Rev 1 01 2014 CHRISTIE 6 Pull the lens with the zoom motor out of the lens mount and then set it on a flat stable surface with the wide end of the lens facing down 7 Install a small lens cap on the rear of the lens Remove the Zoom Motor Assembly 1 Loosen the screw on the zoom motor clamp 2 Slide the clamp upwards of
4. zoom sensor flag a Loosen the screw securing the zoom gear ring and move it backward or forward b Tighten the screw when the adjustment is complete 8 Verify there is a small gap between the zoom motor assembly teeth and the zoom gear ring teeth To adjust the spacing between the zoom motor assembly teeth and the zoom gear ring teeth a Loosen the zoom motor clamp locking screw and move the zoom motor left or right until you can access the adjustment screws b Loosen the adjustment screws A and B and move the zoom motor up or down c Tighten the adjustment screws d Reposition the zoom motor assembly and tighten the zoom motor clamp locking screw Motor Upgrade Kit Update Service Bulletin 9 020 200262 01 Rev 1 01 2014 CHAISTIE 9 Verify the zoom motor shaft is aligned with the lens axis 10 Turn the zoom gear ring to its maximum range in both directions and verify the zoom motor assembly teeth contact the zoom gear teeth throughout the full range of adjustment Readjust the position of the zoom motor assembly if the teeth do not contact the zoom gear teeth throughout the full range of adjustment 11 Tighten the screw on the zoom motor clamp when all adjustments are complete Install the Lens 1 Remove the small lens cap from the rear of the lens 2 Insert the lens with the zoom motor assembly straight into the lens mount without turning it 3 Move the lens clamp to the locked po
5. CHRISTIE SERVICE BULLETIN Motor Upgrade Kit Update Applies to the Following Products Prepared For e CP2220 e CP2230 e CP4220 Internal and External Operators and Service e CP4230 Technicians e D4K25 e D4K35 During lens calibration the 1 6 2 4 1 high brightness zoom lens P N 108 336103 XX might not function as expected with the Motor Upgrade kit 127 102104 XX Symptoms of this issue include e The lens motor hesitates or stutters when moving backward or forward e The lens zoom ring cannot be rotated This document provides information and procedures for installing the replacement Zoom Motor kit P N 003 103912 XX and the Motor Control kit P N 003 101582 02 The installation of these kits corrects the 1 6 2 4 1 high brightness zoom lens movement issue Safety Precautions ELECTRICAL SHOCK HAZARD Always turn off disconnect and disengage all power sources to the projector before servicing Failure to comply results in death or serious injury Only Christie accredited service technicians are permitted to open any enclosure on the projector and only if the AC power has been fully disconnected Failure to comply could result in minor or moderate injury Prerequisites e Solaria Main Software v4 0 or later e Zoom Motor kit P N 003 103912 XxX e Motor Control kit P N 003 101582 02 Motor Upgrade Kit Update Service Bulletin 1 020 200262 01 Rev 1 01 2014 CHRISTIE Resolution This section provides
6. f the lens and set it aside 3 Carefully lift the zoom motor assembly up and away from the zoom ring gear and set it aside me a NS gt RNY s rA N bo A 4 1 4 Place the lens in a safe location where it cannot be damaged Motor Upgrade Kit Update Service Bulletin 3 020 200262 01 Rev 1 01 2014 CHAISTIE Remove the Motor Control Assembly 1 Remove the 2 screws securing the focus motor cover 2 Remove and set aside the focus motor cover and screws 3 Disconnect the 2 focus motor connectors 4 Disconnect the 2 vertical motor connectors T 2 ral y TNG Motor Upgrade Kit Update Service Bulletin 020 200262 01 Rev 1 01 2014 CHAISTIE 5 Disconnect the 2 horizontal motor connectors 7 Loosen but do not remove the 2 screws securing the motor control assembly to the lens mount 8 Slide the motor control assembly up and away from the lens mount and set it aside Motor Upgrade Kit Update Service Bulletin 020 200262 01 Rev 1 01 2014 CHAISTIE Install the Replacement Motor Control Kit 1 Align the replacement motor control assembly over the mounting screws on the lens mount 2 Slide the mounting brackets on the motor control assembly over and down onto the mounting screws until it locks into position 3 Tighten the 2 screws to secure the motor control assembly to the lens
7. sition i j WAIN S ah WI ij Wh VW 4 VW w WII EE H 4 Remove the lens cap from the front of the lens 5 Connect the 2 zoom motor connectors 6 Secure the zoom motor cover to the zoom motor with 2 screws 7 Connect the projector to AC power and turn it on Motor Upgrade Kit Update Service Bulletin 10 020 200262 01 Rev 1 01 2014 CHAISTIE 8 Upgrade the projector software Service or Administrator permissions are required to upgrade the software This procedure is not required if Solaria Main Software v4 0 or later is installed a Download Solaria Main Software v4 0 or later to a USB key The software is available on the Christie website www christiedigital com b Insert a USB flash drive with the software into the USB port on the side of the projector touch panel controller TPC p On the TPC tap Menu gt Administrator Setup gt Upgrade Q Tap Upload Select the location of the upgrade file in the Drive Letter list f Browse to the location of the upgrade file in the Folder list g Tap the upgrade file and then tap Open 9 Calibrate the lens See the User Manual included with your projector Reset the ILS Files and Adjust the Image Position 1 Reset your Intelligent Lens System ILS file settings to restore image positions a Tap Menu gt Advanced Setup gt ILS File Setup b Select an ILS file in the Current ILS File list c Tap
Download Pdf Manuals
Related Search