INSTALLATION AND OPERATION MANUAL
Contents
1. 1 Air may become trapped in the hydraulic system during transit To purge air 2 Open release valve by pulling outward on the handle and turning counter clockwise 3 Pump Handle rapidly 6 8 strokes This will expel air that may have entered oil passages during transit 4 Close release valve by twisting Handle clockwise and pump handle 5 If lift arm is raised jack is ready for use If not just repeat this procedure A CAUTION BEFORE ATTEMPTING TO RAISE ANY VEHICLE CHECK VEHICLE SERVICE MANUAL FOR RECOMMENDED LIFTING POINTS OPERATION 1 To Raise Load Close release valve tightly by twisting Handle clockwise DO NOT OVERTIGHTEN Position jack under load so that saddle will contact load firmly and load is centered so it cannot slip Operate jack handle until saddle approaches the load Once again check to see that saddle is correctly positioned Raise load to desired height Place jack stands of appropriate capacity under the vehicle DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING JACK STANDS 1 Place jack stands at vehicle manufacturer s recommended lift areas that provide stable support for the raised Vehicle Once jack stands are positioned open the release valve VERY SLOWLY by twisting the Handle counter clockwise Lower the load to rest on the jack stands Then make sure that the release valve on the jack is closed tightly twist the Handle clockwise 2 To lowe2. in jack failure Lift only dead weight Always set the hand brake and block the wheels of the vehicle This jack is to be used by professional personnel only In order to avoid a dangerous situation please ensure that non professional personnel and specially CHILDREN DO NOT USE THIS JACK under any circumstances A WARNING THIS IS A LIFTING DEVICE ONLY DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK IMMEDIATELY AFTER LIFTING SUPPORT THE VEHICLE WITH APPROPRIATE MEANS DO NOT EXCEED RATED CAPACITY OVERLOADING CAN CAUSE DAMAGE TO OR FAILURE OF THE JACK A WARNING LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE MANUFACTURER KEEP HANDS AND BODY CLEAR OF ALL PINCH POINTS CENTER LOAD ON SADDLE PRIOR TO LIFTING OFF CENTER LOADS MAY CAUSE DAMAGE TO JACK LOSS OF LOAD PROPERTY DAMAGE PERSONAL OR FATAL INJURY THIS JACK IS DESIGNED FOR USE ONLY ON HARD LEVEL SURFACES CAPABLE OF SUSTAINING THE LOAD USE ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN JACK INSTABILITY AND POSSIBLE LOSS OF LOAD NO ALTERATIONS TO THE JACK SHALL BE MADE READ STUDY AND UNDERSTAND THE OPERATING MANUAL PACKED WITH THIS JACK BEFORE OPERATING FAILURE TO HEED THESE WARNINGS MAY RESULT IN LOSS OF LOAD DAMAGE TO JACK AND OR FAILURE RESULTING IN PROPERTY DAMAGE PERSONAL OR FATAL INJURY ASSEMBLY INSTRUCTIONS 1 Insert handle assembly into Handle Socket and tighten Bolt OPERATING INSTRUCTIONS BEFORE USE
3. KEEP VISITORS AND ESPECIALLY CHILDREN AWAY FROM WORK AREA THIS FLOOR JACK IS TO BE OPERATED BY PROPERLY TRAINED PERSONNEL ONLY OPERATION BY UNTRAINED PERSONNEL MAY RESULT IN INJURY AND OR PROPERTY DAMAGE A WARNING THIS OPERATING MANUAL CONTAINS IMPORTANT DETAILS CONCERNING THE SAFE OPERATION OF THIS FLOOR JACK THE USER MUST READ AND UNDERSTAND THESE DETAILS BEFORE ANY USE OF THE FLOOR JACK THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE OWNER OPERATOR RESPONSIBILITY The owner and or the operator shall study the product instructions and retain them for future reference The owner and or operator shall have an understanding of the product operating instructions and warnings before operating the jack Warning information shall be emphasized and under stood If the operator is not fluent in English the product instructions and warnings shall be read to and discussed with the operator in the operator s native language by the purchaser owner or his designee making sure that the operator comprehends its contents INSPECTION Visual inspection should be made before each use of the jack This inspection should check for abnormal conditions such as cracked welds leaks and damaged loose or missing parts A CAUTION Any jack that appears to be damaged in any way is found to be worn or operated abnormally must be removed from service immediately Any jack that operates abnormally shall be removed from ser
4. PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION BY PROCEEDING YOU AGREE THAT i WARN N G YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL FORWARD THIS MANUAL TO ALL OPERATORS FAILURE TO USE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH INSTALLATION AND OPERATION MANUAL REV A 03 05 2015 P N 5150440 3 Ton Professional Series Garage Floor Jack READ FIRST Model RFJ 3TP REV A 1 Do not operate this machine until you read and understand all the dangers warnings and cautions in this manual Keep this operation manual near the machine at all times Make sure that ALL USERS read this manual SHIPPING DAMAGE CLAIMS When this eguipment is shipped title passes to the purchaser upon receipt from the carrier Consequently claims for the material damaged in shipment must be made by the purchaser against the transportation company atthe time shipmentis received BE SAFE Ranger Floor Jacks are designed and built with safety in mind However proper training and thoughtful operation on the part of the user can increase your overall safety DO NOT operate or repair this equipment without reading this manual and the important safety instructions shown inside R Ranger 1645 Lemonwood Dr Santa Paula CA 93060 USA Tel 1 805 933 9970 Toll Free 1 800 253 2363 Fax 1 805 933 9160 www rangerproducts com WARRANTY POLICY Ranger
5. Products are backed by over 40 years of manufacturing experience Every Floor Jack bearing the Ranger name is sold with the following warranty e Each Ranger Product is warranted to be free from defects in workmanship and material for a period of one year from the date of shipment provided that a written claim for such defect is made within that time This warranty does not cover damage or defects caused by carelessness of the operator misuse abuse or abnormal use which in any way impairs the proper functioning of the equipment or by the use or addition of parts not manufactured by Ranger Products or its suppliers THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE If your Ranger Products equipment is not functioning properly call your Ranger Products dealer immediately On some occasions an independent contractor may be hired to do the repairs Within the warranty period a customer should not hire his own contractor unless a customer is authorized in writing by Ranger Products e If it is necessary to return equipment for repairs your dealer will so advise you When returning equipment for repairs see that machines are properly crated and protected and prepay transportation e Defective parts replaced at no charge must be returned to your dealer or Ranger Products within 60 day
6. e the following informa tion on hand when calling for an RMA number customer name order or invoice number item SKU number and serial number if exists and the reason for the return In addition to the RMA number a completed RMA form must accompany each shipment of returned merchandise No returns of any type will be accepted without an RMA number and completed RMA form Returned items must be shipped via ground service only Do not return items by air unless authorized in writing For warranty related exchanges and or returns a BendPak customer service representative will work with you to arrange to have the item s returned via a BendPak preferred carrier freight collect Products returned C O D will be refused Unauthorized freight collect charges will be denied Once an item arrives at BendPak Ranger we will issue a full or partial credit exchange or refund within 15 days Additional time may be required depending on the nature of the return Returns must be made within 15 days of the Return Authorization being provided Any incurred costs associated with damaged merchandise will be deducted from credits owed BendPak Ranger is not responsible for merchandise damaged in return shipment We strongly recommend you package the items carefully to ensure safe passage For non warranty items we suggest you fully insure your return shipment in case of loss or damage A CAUTION ALWAYS MAINTAIN A CLEAN WORK AREA
7. ecurity Washer 6 37 910 Security Washer 4 a Masas Hex Screw 6 38 LowerHandle 1 18 16 Security washer 4 39 Handle Extension 1 Cio menu 4 40 mossHandeen 1 Tao Screw tor inke 2 41 Mande Grip 17 Ca Pesce 2 S iii A io a I T i RFJ 3TP PARTS BREAKDOWN Bend PROVIDING AUTOMOTIVE SERVICE SOLUTIONS B E m D p A K L For Parts Or Service Contact BendPak Inc Ranger Products 1645 Lemonwood Dr Santa Paula CA 93060 Tel 1 805 933 9970 Toll Free 1 800 253 2363 Fax 1 805 933 9160 www rangerproducts com NOTE Every effort has been taken to ensure complete and accurate instructions have been included in this manual however possible product updates revisions and or changes may have occurred since this printing BendPak Ranger reserves the right to change specifications without incurring any obligation for equipment previously or subsequently sold Not responsible for typographical errors PROVIDING AUTOMOTIVE SERVICE pyko
8. lied e Returned items that failed due to incorrect voltage or improper wiring Returned items that failed due to rain excessive humidity corrosive environments or other contaminants Any item damaged in shipment or any product failure caused by installing or operating product under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings e Returned items with cosmetic defects that do not interfere with product functionality e Returned items with no accompanying RMA number and completed RMA form e Returned items that are incomplete or defaced e Any consumable or standard wear items e Returned items with a different serial number from what was authorized for return e Returned items that do not include your original receipt invoice or sales order e Returned items that were special ordered or custom configured e Freight damaged items If your shipment arrives damaged you must note the damage on the car rier s delivery record in accordance with the carrier s policy save the merchandise in the original box and packing it arrived in and arrange for a carrier inspection of damaged merchandise HOW TO RETURN PRODUCTS e Please contact BendPak Ranger within 14 days of your original shipment or warranty exchange for a Return Merchandise Authorization RMA number before returning your product to BendPak Ranger For faster service please hav
9. load or feels spongy under load Purge air from hydraulic system as above 4 Unit will not lower completely Check the oil level and verify it is not too high Pump the handle rapidly several times to push oil past ball valves in pump 6 Unit still does not operate Contact Parts amp Warranty Department 5 Handle tends to raise up while the unit is under load 3 Unit will not lift to full height Check the oil level and verify it is not too low FEATURES Alloy plated ram Welded lift arm assembly Heavy gauge steel construction Swivel Casters for easy mobility Professional model designed for heavy use Heavy steel construction for maximum durability Sealed hydraulics prevents contamination Built in safety overload system SPECIFICATIONS Raised Height 19 1 4 489 mm 1077279 mm RFJ 3TP PARTS BREAKDOWN No Description aty No Description J oy a sa 2 22 MSScrews a 2 orewasher 2 23 Safety cas 2 Ta wheelwasher 2 24 ove i Ta LeftBracket a 2s Hyorauic Oyinder 1 Cs eau 2 2 mesmes i Te mesnat 2 27 m12 Screw forCoupng 1 T Right Bracket a 28 Pirot Couing 17 Ce im a as oe TTT 9 ra 2 30 25x16 00trPn 1 ao sakea 1 af a Cn p 2 32 18 Securty Washer 2 a2 sping 2 os te Short Bor 1 Tas sasky a s4 m20x18 Spring Washer 2 ia Reinforcementtube 3 35 Rearwheel 2 45 tracions 2 36 mrox20Hecet 4 16 28 S
10. r load Re check to make sure release valve is tightly closed twist the Handle clockwise Then operate the jack handle until the load is raised enough to remove the jack stands Once jack stands are removed open release valve very slowly to lower the vehicle twist the Handle counter clockwise Lower jack completely so that the vehicle is securely resting on the ground and that jack no longer makes contact with vehicle A CAUTION Keep hands or feet away from the hinge mechanism of the jack MAINTENANCE When adding or replacing hydraulic fluid always use a quality hydraulic fluid DO NOT use brake fluid alcohol detergent motor oil dirty oil or any fluid other than quality hydraulic fluid Improper fluids can cause internal damage to the jack and improper or unsafe operation ADDING HYDRAULIC FLUID With the saddle fully lowered and the jack on level ground remove the filler screw Hydraulic fluid should be filled to the level of the filler screw hole If the level is below this hole add hydraulic fluid as needed LUBRICATION All moving joints require lubrication often Lightly grease saddle post and saddle bottom Remove handle and grease the lower end of handle where it rotates in the handle socket Oil all lift arm linkages front wheels and rear casters TROUBLESHOOTING 1 Unit will not lift load Purge air from hydraulic system by following procedure under OPERATING INSTRUCTIONS page 4 2 Unit will not sustain
11. s of the date that the replacement parts are shipped otherwise you must pay for the replacement parts at the current selling price LIMITED RETURNS EXCHANGE POLICY BendPak Ranger prides itself on a tradition of outstanding customer care and support Our devoted team of account representatives understands that our customers are the hallmark of our enduring partnerships Our limited return and exchange policy allows you to return defective or incorrect merchandise for a full or partial credit of your order All returned merchandise requires authorization Contact our service agents first for shipping instructions and to obtain a return authorization number Credit will not be issued unless authorization to return merchandise has been received For all merchandise returned to BendPak Ranger for reasons other than warranty a 20 restocking fee and round trip shipping costs will be deducted from the credit refund All returned items must be in their original box or crating and must include all packing material manuals and all accessories At our discretion a restocking fee may be charged if your product is opened or is not returned in its original condition box or is missing packing material manuals or any accessories NO RETURNS CREDITS OR EXCHANGES FOR e Returned items that failed due to an accident purchaser s abuse neglect or failure to operate in accordance with instructions provided in the owner s manual s supp
12. vice until repaired by a qualified repair service center If the jack is accidentally subjected to an abnormal load or shock it must be taken out of service immediately and be inspected by a qualified repair or service center It is recommended that an annual inspection is performed on the jack and that any damaged or worn parts decals or warning labels be replaced with manufacturer s specified parts ALTERATIONS Because of potential hazards associated with this type of equipment no alterations shall be made to the product FOR YOUR SAFETY AND TO PREVENT INJURY Use Service Jack for lifting purposes ONLY Make sure to always support vehicle with jack stands UPON DELIVERY e Carefully remove all packaging material Inspect the equipment and all parts for any signs of concealed shipment or storage damages e Rememeber to report any shipping damage to the carrier and make a notion on the delivery receipt IMPORTANT SAFETY TIPS e Be sure to read all warning labels and the instruction manual prior to operation of this equipment e Keep hands and body clear of all pinch points e Use the jack for loading under rated capacity only DO NOT over load e Ensure the jack is set on a solid and level surface Support the load with jack stands after the load is raised to the desired level before getting under the load Center the load on the jack saddle properly An off centered load may damage the seals and result
Download Pdf Manuals
Related Search