MSR42 / MSRK42 - Honeywell Integrated Security
Contents
1. MSR42 MSRK42 MAGNETIC SWIPE CARD READER SERIES TECHNICAL MANUAL WSE 47102 Mission Falls Court Fremont CA 94539 an ISO 9001 certified company 0 360 7820 P N 66109102001 Rev B Copyright 1999 WSE All rights reserved Printed in the United States of America MSR42 MSRK42 Magnetic Swipe Reader Series LIMITED WARRANTY WSE warrants to the original user the equipment manufactured by WSE as described herein to be free from defects in material and workmanship for a period of one year from the date of purchase by such user or fifteen 15 months from the date of shipment from the factory whichever is sooner command key magnetic stripe card warranties differ see below provided WSE has been notified within such period by return of any alleged defective eguipment free and clear of any liens and encumbrances to WSE or its authorized dealer at the address specified transportation prepaid and II the equipment has not been abused misused or improperly maintained and or repaired during such period and Hl such defect has not been caused by ordinary wear and tear and IV such defect is not a result of voltage surges brownouts lightning water dam age flooding fire explosion earthquakes tornadoes acts of aggression war or similar phenomena and V accessories used as integral to WSE systems have been approved by WSE e g coax batteries etc and VI the equipment has been installed th2. MRS42 and MSRK42 series readers are for use in low voltage class 2 circuits Voltage 12 VDC Current 80mA 50mA typical Interface RS 485 two wires multidrop Dimension 1 95 50mm W x 1 30 33mm H x 5 50 140mm L Temperature 55 to 85 degrees C storage 40 to 75 degrees C operating Humidity 0 95 RHNC standard 100 GW options 66109102001 Rev B A 1 MSR42 MSRK42 MSR42 MSRK42 Series Magnetic Swipe Readers Appendix A MSR42 MSRK42 A 2 66109102001 Rev B APPENDIX B DIMENSIONS 13 33 2X 0 18 4 5 A MOUNTING HOLE 5 5 3 3 140 m 1 Q SAN 2 0 50 mM 4 DIMENSION INCH mm Figure B 1 Reader Mounting Dimensions 6 3 160 28 3 3 84 Li a E ba A Ne J 1 4 36 S 4 0 102 gt Figure B 2 Optional Wall Plate Dimensions 66109102001 Rev B B 1 MSR42 MSRK42 MSR42 MSRK42 Magnetic Swipe Reader Series ne 2 RIGID s CONDUIT Un ne 1 GANG BOX MSR42 MSRK42 B 2 Appendix B 2 3 57 42 107 WALL OPENING For J BOX Figure B 3 Fitting Rigid Conduit to Junction Box 66109102001 Rev B
3. are possible The information contained in this manual assumes that the person reading it is familiar with access control and alarm monitoring technology and standard installation practices Thus the manual is not intended to be a complete system installation guide or system service manual for dealers or end users As such the manual is a supplementary guide providing only information and data which is unique to MSR42 and MSRK42 Series Magnetic Swipe Card Readers The information provided in this manual is not intended to either conflict with or supplement the specific building codes electrical codes or safety codes to which any given installation must conform This manual is organized as follows Section 1 INTRODUCTION Section 2 DESCRIPTION Section 3 INSTALLATION Section 4 MAINTENANCE Appendix A SPECIFICATIONS Appendix B PRODUCT IDENTIFICATION 66109102001 Rev B 1 1 MSR42 MSRK42 Introduction MSR42 MSRK42 Magnetic Swipe Readers Manual MSR42 MSRK42 1 2 661091020001 Rev B SECTION 2 DESCRIPTION 2 1 GENERAL INFORMATION The MSR42 and MSRK42 family of magnetic card readers are designed for reading standard or high coercivity magnetic stripe cards Each reader will operate at up to 28 volts DC and is supplied in a die cast metal housing resistant to corosion abraision and tampering Other f
4. on off on 66109102001 Rev B Device address N O Switch Jumper Position 4 3 2 on on on on on on on on off off off off on on on on off off on on off off on on 1 SWIICH Device address m IT OQ O UJ gt o o Figure 3 6 Setting the Address Switch MSR42 MSRK42 MRS42 MSRK42 Magnetic Swipe Reader Series Installation MSR42 MSRK42 3 6 66109102001 Rev B SECTION 4 MAINTENANCE AND TROUBLESHOOTING 4 1 MAINTENANCE The readers are designed to provide continuous service with minimal routine maintenance However contaminants such as magnetic oxides from badges and dirt tend to accumulate on the read head Without regular cleaning these contaminants will shorten the read head life and increase the probability of card read error A maintenance schedule should be developed based on the card reader environment dirty or clean and the usage frequency light traffic or heavy traffic Readers placed in extremely dirty environments may require daily cleaning Head cleaning may be done by using disposable pre saturated magnetic head cleaning cards These cards are readily obtainable from a number of sources e g Clean Team Co 805 581 1000 The reader exterior surface is covered with a high strength polymer and polyester membrane It may be cleaned with a soft cloth and mild detergent if required 4 2 CUSTOMER SERVICE 4 2 1 PRODUCT IDENTIFICATION If a prob
5. 5 Dropping Resistor not used behind plate Black Common Red 28V Orange Brown not used Figure 3 4 Connecting the reader to 12 volt supplies 66109102001 Rev B 3 3 MSR42 MSRK42 MRS42 MSRK42 Magnetic Swipe Reader Series Installation 3 2 4 Grounding the Reader To avoid having ESD electro static discharge interfering with the operation of the reader the reader casing must be grounded This can be accomplished be tying the mounting bracket to earth ground locally e g grounded conduit Please consult Figure 3 5 below RS 485 Power amp Return Controller Figure 3 5 System Connections Diagram MSR42 MSRK42 3 4 66109102001 Rev B MRS42 MSRK42 Magnetic Swipe Reader Series 3 2 5 DIP switch setting Installation The DIP switch on the MSR42 MSRK42 series readers is used to set the device address Each reader is equipped with DIP switches used to set a physical address Refer to software manuals for a detailed description of the address switches and their use DIP switches are set by moving the slide to on off position using a small tool may be made from a paper clip Remove the top bracket to access the DIP switches Switch Jumper Position 4 3 2 off off off off off off off off off off off off on on on on off off on on off off on on 1 off on off on off
6. ctrical interface In any case cable with wires of 24AWG or larger diameter are recommended for field wiring 3 2 2 RS 485 Interface The RS 485 interface is two wire half duplex An on board End of Line cable termination is provided If the reader is the last device on the bus install a jumper to activate the terminator Refer to Figure 3 1 for the location of the terminator jumper For communication reliability a low capacitance cable of 24AWG twisted pair of wires with 120 ohm characteristic impedance must be used Observe the following signal pairing power ground and TR TR Figure 3 2 shows a typical RS 485 device wiring Maintaining signal ground connection between devices is essential for reliable communication MODULAR PLUG 6 BLACK GROUND AG 5 ORANGE NOT USED E 4 BROWN NOT USED 3 WHITE RS 485 2 GREEN RS 485 1 RED 12 VDC Figure 3 2 Detail Showing The Modular Plug MSR42 MSRK42 3 2 66109102001 Rev B MRS42 MSRK42 Magnetic Swipe Reader Series Installation 3 2 3 12 or 24 Volt Operation The MSR42 and MSRK42 series readers can be operated from either 12 or 24 volt supplies by using a special dropping resistor pre attached to the mounting plate at the factory If 24 volt operation 16 28 VDC is required consult Figure 3 3 If 12 volt operation 8 14 VDC is required consult Figure 3 4 instead Red 7 Red ALL RS 485 White l Orange Brown RS 48
7. e installation supervised or installation tested by an authorized WSE dealer WSE MAKES NO OTHER WARRANTY AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY PERIOD AS SET FORTH ABOVE WSE S MAXIMUM LIABILITY HEREUNDER IS LIMITED TO THE PURCHASE PRICE OF THE EQUIPMENT IN NO EVENT SHALL WSE BE LIABLE FOR ANY CON SEQUENTIAL INDIRECT INCIDENTAL OR SPECIAL DAMAGES OF ANY NATURE ARISING FROM THE SALE OR USE OF THE EQUIPMENT Some states do not allow limitations on incidental or consequential damages or how long an implied warranty lasts so the above limitations may not apply This warranty gives specific legal rights however other rights which vary from state to state may pertain Analog command keys are warranted for 5 years digital command key magnetic stripe card warranties vary See product literature 66109102001 Rev B i MSR42 MSRK42 NOTICE The MSR42 and MSRK42 series of Magnetic Card Swipe Readers sold by WSE have been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions herein may cause harmful interfere
8. eatures include Two high brightness red green status indicators a tamper detection switch address switches WSE proprietary S Net protocol and an RS 485 interface MSRK42 readers also provide a 12 key keypad for PIN entry hence the K in MSRK42 Figure 1 below gives the basic block diagram of the key components in the MSR42 and MSRK42 series readers Status Indicators MSRK42 only RS 485 ie DERE Communications Interface S Net Tamper Protocol Detect Figure 1 1 MSR42 MSRK42 Functional Block Diagram 66109102001 Rev B 2 1 MSR42 MSRK42 Description MSR42 MSRK42 Magnetic Swipe Readers Manual 2 2 CONFIGURATIONS The MSR42 and MSRK42 Series Magnetic Swipe Card Readers are each available in two configurations weatherized and non weatherized as shown in Table 1 1 below Table 1 1 MSR42 and MSRK42 Configurations Model PartNumber Description mee e m MSR42 G 92422201000 reader pup er ud MSR42 GW 92422211000 reader with weatherization Swipe style magnetic stripe card MSRK42 G 92422203000 reader with integral keypad Swipe style magnetic stripe card MSRK42 GW 92422213000 reader with integral keypad and weatherization MSR42 MSRK42 2 2 66109102001 Rev B SECTION 3 INSTALLATION 3 1 LOCATION AND MOUNTING 3 1 1 Mounting the reader Find a suitable location to anchor the reader mounting bracket The mounting of the reader does not re
9. lem with the reader occurs which might require consulting WSE Customer Service please note the model and serial numbers contained on the Product ID label This label is located on the rear of the reader behind the mounting plate and contains other useful information PIN FUNCTION WIRE COLOR WSE an ISO 9001 certified company svpcn 1 2 u sj GREEN MADE IN U S A 3 RS 485 WHITE MODEL MSR42 G 4 NOT USED BROWN P N 92422201000 REV 5 NoT SED ORANGE RATED 25VDC 0 25W SERIAL NO 6 COMMON BLACK ACCESS FOR 24 V OPERATION CONNECT PIN 1 TO R1 24 VDC RED CONTROL PIN R2 24 V IS SUPPLIED TO PIN R1 R2 412 VDC OUT RED N L7 294 UNIT FOR 12 V OPERATION CONNECT PIN 1 usreDsezz ACCESSORY DIRECTLY TO 12 V R1 AND R2 ARE NOT USED REFER TO MANUAL FOR INSTALLATION INSTRUCTIONS 4 2 1 PRODUCT RETURN POLICY 66109102001 Rev B 4 1 MSR42 MSRK42 MSR42 MSKR42 Magnetic Swipe Reader Series Troubleshooting And Maintenance If the problem can not be rectified by the replacement of a faulty cable or interface wiring call WSE Customer Service for a Return Authorization Units returned without a Return Authorization will be refused Return faulty units to the following address WSE 47102 Mission Falls Court Fremont CA 94539 7818 If you need to talk to a WSE Customer Support Technician for assistance call the following phone number 1 800 227 1667 4 3 TROUBLESHOOTING GUIDE Troubleshooting
10. nce to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help MSR42 MSRK42 ii 66109102001 Rev B MSR42 MSRK42 Magnetic Swipe Reader Series TABLE OF CONTENTS MSR42 MSRK42 MAGNETIC CARD SWIPE READERS SECTION 2 DESCRIPTION 2 1 GENERAL INFORMATION I ennt nennen 2 1 2 2 CONFIGURATIONS 4 non cece enne 2 2 SECTION 3 INSTALLATION 3 1 LOCATION AND MOUNTINGQ a 3 1 3 1 1 Mounting the Reader 3 1 3 1 2 Weatherproofing the 3 1 3 2 WIRING REQUIREMENTS I a 3 2 3 231 Reader Wiring ete b eee bae gen tete 3 2 3 2 2 RS 485 Interface nn oo 3 2 3 2 3 12 or 24 Volt Operation sss 3 3 3 2 4 Grounding the Reader nanna rna 3 4 3 2 5 DIP Switch nde eee dee rae
11. of the MSR42 and MSRK42 series readers in the field is limited to checking continuity of the conductors in the interface cables and analyzing probable fault conditions from the status of the LEDs Be sure to consult software documentation A troubleshooting guide is provided in Table 4 1 Table 4 1 MSR42 MSRK42 Troubleshooting Guide No Status LEDs are on No power is getting to the Check power connections reader Observe polarity Low power at reader Verify that reader is wired for terminals correct voltage Reader doesn t come on line Unit not being addressed Check Address Switch Make properly certain software is properly initialized RS 485 lines not connected Check RS 485 wiring properly Reader misreads cards Dirty reader Clean read head Bad power incorrect wiring Check power wiring Reader functions but not Software not correctly Initialize software keypad initialized MSR42 MSRK42 4 2 66109102001 Rev B MSR42 MSKR42 Magnetic Swipe Reader Series Troubleshooting And Maintenance Table 4 1 Cont d MSR42 MSRK42 Troubleshooting Guide Reader seems to run hot Reader is being operated ata Verify unit is wired for the voltage which is too high correct voltage Reader blinks every minute No problem Normal Indication 66109102001 Rev B 4 3 MSR42 MSRK42 MSR42 MSKR42 Magnetic Swipe Reader Series Troubleshooting And Maintenance MSR42 MSRK42 4 4 66109102001 Rev B APPENDIX A SPECIFICATIONS The
12. qe d u 3 5 SECTION 4 MAINTENANCE AND TROUBLESHOOTING 4 1 MAINTENANDGE 3 5 ini bets 4 1 4 2 CUSTOMER SERVICE eio eet Hee tae de dee ei 4 1 4 3 TROUBLESHOOTING GUIDE sese 4 2 APPENDIX A SpecificatiOns cecinere ane ak l Pane A 1 APPENDIX B Product Identification nennen B 1 66109102001 Rev B iii MSR42 MSRK42 MSR42 MSRK42 iv 66109102001 Rev B SECTION 1 INTRODUCTION This manual provides basic information on the installation and operation of the WSE MSR42 and MSRK42 Series Magnetic Swipe Card Readers This information includes specifications a brief description of the operation controls and indicators relevant installation data and a troubleshooting guide NOTE Changes or modifications to the equipment described herein which are not expressly approved by WSE can invalidate regulatory approvals and may void statutory authority of the user to operate the system 1 1 PURPOSE The purpose of this manual is to provide the information required for installing operating and troubleshooting MSR42 and MSRK42 Series Magnetic Swipe Card Readers 1 2 SCOPE The information provided in this manual is intended for personnel who will be installing MSR42 and MSRK42 Series Magnetic Swipe Card Readers placing the units in operation and performing the troubleshooting procedures described herein No repairs to the units other than cleaning and switch settings
13. quire a junction box However rigid conduit is required for outdoor application A single gang junction box may used to provide transition to rigid conduit If a single gang junction box is used a wall plate optional may be used to cover the junction box The reader is then secured to the mounting bracket using a screw Refer to figures for reader dimensions and typical junction box usage 3 1 2 Weatherproofing the Reader The reader is rated for operation over extended temperature However if the reader is expected to be exposed to weather the weatherizing option GW must be ordered The option is implemented in two parts With the weatherizing option the electronics are conformally coated against moisture A tube of dielectric grease is supplied for the installer KEYPAD CONNECTOR DIELECTRIC GREASE RJ 11 JACK Figure 3 1 Reader weatherization Also shows key component locations shown is the MSRK42 GW the MSR42 GW does not have a keypad connector 66109102001 Rev B 3 1 MSR42 MSRK42 MRS42 MSRK42 Magnetic Swipe Reader Series Installation 3 2 WIRING REQUIREMENTS 3 2 1 Reader Wiring The reader provides an RJ 11 modular jack for easy field connection A small piece of pre terminated cable is supplied with each standard reader for field wiring The pre terminated cable has non standard colors Refer to the pin numbers if the pre terminated cable is not used The signal wire assignment is different for each ele
Download Pdf Manuals
Related Search