ISO Test Report - Elevation
Contents
1. 1 Static strength tests Test position Force applied Remarks Ame Downward n a No armrests n a Upward n a No armrests n a Downward 1165 N Pass Pass Footrests Upwards each n a n a n a Upwards single 1010 N Pass Pass Tipping levers n a No tipping levers n a Handgrips n a No handgrips n a Each single n a n a n a Push RANGES Bar type 1995 N Pass Pass 2 Impact strength tests Test position Test condition Remarks Result 25kg pendulum 30 2 applications Backrest two applications ja 30 Pass 10kg pendulum 45 2 applications Hand rim two applications z 30 Pass 10kg pendulum 45 2 applications Castor two applications A 30 Pass Lateral 10kg pendulum 45 2 applications Pass two applications 30 Footrests Longitudinal 10kg pendulum 45 2 applications two applications 30 Pass Frontal 10kg pendulum 45 2 applications Pass two applications 30 Frant sinyor Offset 10kg pendulum 45 2 applications two applications 30 Pass 3 Two drum fatigue test Test condition Remarks Result Speed 1 0 metre sec 74 RPM 1 0 m sec rotation speed Baas 200 000 cycles 200 000 cycles 4 Kerb drop fatigue test Test condition Remarks Result Height of drop 50 mm 16 cycles min Pass 6 666 cycles 6 666 Cycles jacm NATA NATA Accredited Laboratory No 2953 Page 8 of 12 ANN NI This document shall not be reproduced except in full Tester s Initials RP WW x a A2. 5 Stowage width 610 mm 6 Stowage height 450 mm 7 Rising Not measured 8 Total mass 12 0 kg 9 Mass of heaviest part n a 10 Pivot width 515 radius 11 Reversing width Not measured 12 Turning diameter 1150 mm 13 Ground clearance 50 mm 14 Required width of angled corridor Not measured 15 Required doorway entry depth 650 mm 16 Required corridor width for side opening 875 mm jacm NATA NATA Accredited Laboratory No 2953 Page 6 of 12 BeN This document shall not be reproduced except in full Tester s Initials RP WW ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM ye Job Number 491985 1 ISO 7176 7 1998 Wheelchairs Determination of seating and wheel dimensions An RLG is positioned in the wheelchair seat so as to provide repeatable deformation of the wheelchair and seat structure Measurements of seating and wheelchair dimensions are made to reference points and planes on the RLG Reference loader gauge 2 Measurement procedure 2 1 Selection of correct RLG size Adult or child 2 2 Positioning of the RLG 2 3 Recording of measurements 3 Result of measurements Dimension Fixed or min value Maximum value 5 N of increments 1 Seat plane angle Not measured 12 Seated Stepless 2 Effective seat depth 415 mm 415 mm 1 3 Seat width 400 mm 400 mm 1 4 Effectiv
3. 491985 1 y r Cause in Result of ISO 7176 Test Requirement e Verification 1 1999 3 2 For electrically powered wheelchairs Test plane Direction of Normal Reverse Emergency Result Comments angle travel operation command power off 0 Forwards Min braking diet n a n a n a a MWC Max speed m s n a a Min braking dist M 0 Reverse Max spe d tile n a n a n a n a MWC s Forwards Min braking dist M 2 downhill Max speed m s n a n a n a n a MWC 7 Reverse Min braking dist M 3 downhill Max speed m s n a n a n a n a MWC 5 Forwards Min braking dist M downhill Max speed m s n a n a n a n a MWC Reverse Min braking dist M downhill Max speed m s n a n a n a n a MWC o Forwards Min braking dist M a downhill Max speed m s n a n a n a n a MWC A Reverse Min braking dist M R downhill Max speed m s n a n a n a n a MWC ISO 7176 5 2008 Wheelchairs Determination of dimensions mass amp manoeuvring space Accreditation No 2953 1 Wheelchair classes and occupant mass groups Classes of electrically powered wheelchairs Group 1 muk EE a a Occupant mass groups Group II A eee 50 kg 2 Measurement of dimensions Measurement position component Record mm 1 Full overall length 825 mm 2 Overall width 650 mm 3 Handgrip height 590 865 mm 4 Stowage length 750 mm
4. Pass 2 4 2 Wheelchair in the most stable configuration Pass 3 Results Least stable Most stable onward Front wheels locked gt 10 0 gt 10 0 Front wheels unlocked gt 10 08 gt 10 0 Rear wheels locked 5 4 TOS Rear Rear wheels unlocked 4 3 5 4 Anti tip devices gt 10 0 gt 10 0 Sideways Left gt 10 0 gt 10 0 Right gt 10 0 gt 10 0 Least stable amp Most stable refer to the positioning of the anti tip devices ISO 7176 3 2003 Wheelchairs Determination of effectiveness of brakes A number of wheelchair braking operations are carried out and the resulting responses of the wheelchair are measured and observed 2 1 Parking brakes Pass 2 2 Running brakes normal operation n a 2 3 Running brakes operation by reverse command n a 2 4 Running brakes emergency operation n a 2 5 Parking brakes fatigue Pass 3 Test results 3 1 For manual chairs Requirement Facing downhill Facing uphill Angle of the plane when movement 310 76 commences The type of movement No creep or slipping Brakes fatigue 60 000 cycles 60 000 cycles Pass RNS ky LO Oe AIN ig ne ee jiae wRA NATA NATA Accredited Laboratory No 2953 _ Page 5 of 12 PENS NS This document shall not be reproduced except in full Tester s Initials RP WW gt Accreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number
5. Test for static stability in the forward direction a For wheelchairs without lockable front wheels as specified in 2 1 1 amp 2 1 3 only Pass b For wheelchairs with lockable front wheels as specified in 2 1 1 to 2 1 4 Pass Adjustable wheelchair component Least stable Most stable Rear wheel position fore aft Forward Back Castor attachment to frame fore aft Back Forward Seat position fore aft Forward Back Seat position vertical High Low Seat back position fore aft Forward Back Seat back position recline Upright Back Seat position tilt Upright Back Elevating leg rest position Up Down 2 1 1 Wheels unlocked and the wheelchair in the least stable configuration Pass 2 1 2 Wheels locked and the wheelchair in the least stable configuration Pass 2 1 3 Wheels unlocked and the wheelchair in the most stable configuration Pass 2 1 4 Wheels locked and the wheelchair in the most stable configuration Pass 2 2 Test for static stability in the rearward direction a For wheelchairs without lockable rear wheels as specified in 2 2 1 amp 2 2 3 only Pass b For wheelchairs with lockable rear wheels as specified in 2 2 1 amp 2 2 4 Pass Adjustable wheelchair component Least stable Most stable Rear wheel position fore aft Forward Back Castor attachment to frame fore aft Back Forward Seat position fore aft Back Forward Seat position vertical High Low Seat back position recline Back Upright Seat position tilt Back U
6. Date n a TESTING AUTHORITY NOVITA CHILDREN S SERVICES NOVITATECH TEST LABORATORY 171 Days Road Regency Park South Australia 5010 Telephone 08 8243 8289 Fax 08 8243 8208 Testing supervisor Wayne Wurfel DN CN Wayne Wurfel C Senior Test Technician AU O NovitaTech OU A Novitatech Test laboratory Authorised signatory DW uhel Reason attest to the accuracy and integrity of this document Checked Richie Petronio Test Technician Dates of testing period Date of issue of this report September October 2013 28 October 2013 wl AN SVS 1 RA aG MR NATA NATA Accredited Laboratory No 2953 eal Pic ut n RS i i i ester s Initials RP Goo WW This document shall not be reproduced except in full K X rh Accreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 Manufacturer Name Address Chair type Frame Size Frame Tilt Recline Anti tips Push handles Footrests Armrests Headrest Seating Backrest Width Height Description Seat Width Depth Description Wheels Castor Width Diameter Description Drive Wheel Width Diameter Description Other features Set up details to ISO PRODUCT DETAILS Product Design Group Inc Unit 103 318 East Kent Avenue South Vancouver BC Canada V5X4N6 Manual wheelchair with seat elevation function Adult Rigid frame with seat elevation No No Yes Single bar type
7. ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 TEST REPORT FOR Product Design Group Inc Elevation Manual Wheelchair 115 kg 253 Ib REFERENCED DOCUMENTS 1ISO7176 1 1999 ISO7176 3 2003 ISO7176 5 2008 1ISO7176 7 1998 ISO7176 8 1998 ISO7176 13 1989 1ISO7176 15 1996 ISO 7176 22 2000 LABORATORY REFERENCE 491985 1 28 October 2013 NATA Accredited Laboratory No 2953 This document shall not be reproduced except in full Page 1 of 12 Tester s Initials RP WW ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM ye Job Number 491985 1 TEST REPORT This report may NOT be reproduced in part without written laboratory authorisation The NovitaTech Test Laboratory has no control over the selection of test samples Any extension of the findings of this report to cover production items must be based on the production being truly represented by the sample s PRODUCT Job no 491985 1 Name and Model No Product Design Group Elevation MWC Serial no s of test sample 64749 Maximum user mass 115 kg 253 Ibs Documents used in testing ISO7176 1 1999 ISO7176 3 2003 ISO7176 5 2008 ISO7176 7 1998 ISO7176 8 1998 ISO7176 13 1989 ISO7176 15 1996 ISO 7176 22 2000 SUPPLIER Name Product Design Group Inc Address Unit 103 318 East Kent Avenue South Vancouver BC Canada V5X4N6 Telephone 604 323 9220 Fax n a Contact person Torr Brown Order No n a Order
8. Single 1 piece open loop design None fitted None fitted 400 mm 420 mm Sling type fabric 400 mm 420 mm Sling type fabric Front 35 mm 125 mm Solid tyres 25 mm 610 mm Spoke wheels with pneumatic tyres Rear n a n a n a Ultra light weight elevating seat function folding backrest As per ISO standards requirements Ambient test temperature 21 C Note Other descriptive dimensions etc may be included in part 5 and 7 of the test report wy AN NW Y SO jaca NATA Accreditation No 2953 NATA Accredited Laboratory No 2953 This document shall not be reproduced except in full Page 3 of 12 Tester s Initials RP WW ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 4 Clause in ISO 7176 1 1999 Test Requirement Result of Verification Wheelchairs Static stability Depending on the direction of tip wheelchairs can tip about the point of contact with the ground when the wheels are locked with respect to the frame or about the wheel axle when the wheel locks are not applied The angle of slope on which the wheelchair will tip about the most unstable axis is measured on a test plane with an adjustable slope by increasing the angle of the test plane until the tipping angle is reached 2 1
9. ansfer of the user to and from the wheelchair Pass Illustrations to clarify these instructions Pass Any common misuse of the wheelchair known by the manufacturer that might lead to a personal injury or damage to the wheelchair Pass e i Maintenance instructions accompanied by annotated illustrations and the following Any service maintenance amp or fault finding for which the manufacturer intends the user to page be responsible for Information about the types of tools or equip needed for repair and servicing NA Frequency of maintenance Pass A list of materials necessary including part numbers and procurement information NA Identification of circumstances in which an operation should be undertaken by the P ss manufacturer distributor or service agent e ii Instructions and methods of cleaning Pass e iii For parts that the manufacturer intends to be readily replaced the following order information Pass Instructions for access removal Pass replacement and testing Pass Annotated illustrations of the parts including tyres amp batteries amp their locations Pass e iv Information on how to perform potentially hazardous maintenance operations such as pass battery servicing and tyre inflation f Instructions for carrying out performance checks Pass g Description of wheelchair repair procedures as follows Pass g i Identification of parts that are intended to be repaired by the user Pass g ii Identification of pa
10. ation certificates throughout the test period or were checked against traceable Standards before and after use 4 The NovitaTech Test Laboratory has no control over the selection of test samples Any extension of the findings of this report to cover production items must be based on production being truly represented by the sample s 5 Any non conformances are indicated in red END OF REPORT Oly aN PVs SO Pg a eg jiac wRA NATA NATA Accredited Laboratory No 2953 Page 12 of 12 eN NS This document shall not be reproduced except in full Tester s Initials RP WW Accreditation No 2953
11. ccreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM ye Job Number 491985 1 ISO 7176 22 2000 Wheelchairs Set up procedures 1 Adjusting the wheelchair Value position Adjustable parameter Type of equipment ee Air pressure in pneumatic tyres and drive wheels TLE067 As per marking Air pressure in pneumatic tyres castors n a n a Distance between the brake blocks amp their TLE77 53 N engaged contact surfaces Drive wheel axle position horizontal n a n a Drive wheel axle position vertical n a n a Drive wheel camber TLE148 90 Drive wheel track width TLE048 550 mm Castor stem housing position horizontal n a Fixed Castor stem housing position vertical n a Fixed Castor wheel axle position vertical TLE148 Fixed Castor wheel track width TLE084 445 mm Castor stem angle fore aft plane TLE148 Fixed Castor stem angle lateral plane TLE148 Fixed Seat depth TLE048 415 mm Backrest height TLE048 370 mm Seat plane angle Inclinometer 12 Seated Backrest angle Inclinometer 14 5 48 Leg to seat surface angle Inclinometer 80 105 Footrest angle Inclinometer 4 0 Footrest clearance n a n a Control device mounting n a n a Control device electrical settings n a n a Other electrical control devices n a n a Footrest height TLE048 40 90 mm 2 Final adjustments Value p
12. d shall have wads precedence over i d Maximum occupant mass Pass 6 Test report Are performance values resulting from the testing of a specific model of wheelchair to parts of Bade ISO 7176 disclosed as specified in the relevant part of ISO 7176 7 Documentation General 7 1 Is the following information available in the official language of the countries in which the wheelchair is marketed a The specification sheets Pass b A statement as to which features and options are included in specific models Pass c A description of the intended user eg mass indoor outdoor use etc Pass Either i details of warranty Pass a Or ii If no warranty is provided a statement to that effect Pass e Information on how to get repairs and service Pass f Information as to whether a service manual is available Pass g A user manual Pass 7 2 User manual At least 1 copy of the users manual to be supplied with the wheelchair Pass Where illustrations are used Components numbered or named for positive identification Pass Illustrations numbered or named for positive identification Pass 7 3 Contents of user manual User manual to contain the following information a Details of the warranty as specified in 7 1d Pass b General characteristics as follows b i Description of the wheelchair type accompanied by pictures or drawings of the wheelchair amp P ss a non technical description of how the chair is intended to be used b ii Description of the
13. e seat width 400 mm 400 mm 1 5 Seat surface height front edge 450 mm n a 1 6 Backrest angle 14 5 48 0 Stepless 7 Backrest height 370 mm 370 mm 1 8 Backrest width 400 mm 400 mm 1 9 Headrest in front of backrest n a n a n a 10 Headrest height above seat n a n a n a 11 Footrest to seat 385 mm 425 mm 12 Footrest clearance 50 mm 90 mm 13 Footrest length 105 mm 105 mm 14 Footrest to leg angle 90 Not measured 15 Leg to seat surface angle 80 105 16 Armrest height n a n a n a 17 Front of armrest to backrest n a n a n a 18 Armrest length n a n a n a 19 Armrest width n a n a n a 20 Armrest angle n a n a n a 21 Distance between armrests n a n a n a 22 Front location of armrest structure n a n a n a 23 Hand rim diameter 545 mm 545 mm n a 24 Propelling wheel diameter 620 mm 620 mm n a 25 Horizontal displacement of wheel axle Not measured Not measured n a 26 Vertical displacement of wheel axle Not measured Not measured n a 27 Castor wheel diameter 125 mm 125 mm 1 jacm NATA NATA Accredited Laboratory No 2953 _ Page 7 of 12 aN This document shall not be reproduced except in full Tester s Initials RP WW Accreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 y r ISO 7176 8 1998 Wheelchairs Requirements and test methods for static impact amp fatigue strengths
14. intended user including maximum occupant mass Pass b iii The environment in which the wheelchair is intended to be used and any other environmental Pass conditions that might be harmful to the wheelchair such as temperature and humidity b iv If pneumatic tyres are fitted the recommended inflation pressure or range in kPa Pass c If the wheelchair is marketed for user assembly shall contain the following information c i A list of components Pass c ii Information about tools or equipment needed to assemble the wheelchair Pass c iii Instructions on how to inspect for missing or damaged parts Pass RVA ASN jaewRA NATA NATA Accredited Laboratory No 2953 Page 10 of 12 AA This document shall not be reproduced except in full Tester s Initials RP WW ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 Accreditation No 2953 Clause Requirement Result c iv Instructions for assembly installation or removal of any parts supplied by the manufacturer Pass c v Instructions on how to prepare the wheelchair for storage shipment or travel Pass Instructions for operation of the wheelchair as follows d Complete operating instructions for safe use including Instructions for operating the wheelchair on surfaces likely to be encountered by the user Pass d i Instructions for tr
15. mm 400 mm Folded width 610 mm 610 mm Seat surface height at front edge 450 mm n a Folded height 450 mm 450 mm Backrest angle 14 5 48 0 Total mass 12 0 kg 12 0 kg Backrest height 240 mm 370 mm Mass of heaviest part n a n a Footrest to seat distance 385 mm 425 mm Static stability downhill gt 10 gt 10 Leg to seat angle 80 mm 105 mm Static stability uphill 5 4 7 6 Armrest to seat distance n a n a Static stability sideways gt 10 gt 10 eesti ot armrest n a n a Energy consumption n a n a Hand rim diameter 545 mm 545 mm Dynamic stability uphill n a n a Horizontal location of axle n a n a Obstacle climbing n a n a Minimum turning radius 515 mm 515 mm Minimum braking distance n a n a Maximum speed forward n a n a from max speed The sample submitted for this test satisfies the relevant requirements of ISO 7176 1 1999 except the methods indicated in this report as not tested and or tested with deviations NOTES 1U s Uncertainty of measurements where not specified linear 1mm angular 30 force mass 1 temperature 1 C cycles 1 count This means the true measurement is within the stated tolerances at least ninety five times in one hundred 2 All testing was carried out in a controlled environment laboratory using methods set out in the Standards documents all deviations and additions to the Standards methods are noted in remarks 3 All instruments either carried valid calibr
16. osition Adjustable parameter Type of equipment AERONA Backrest angle Inclinometer 79 Seat plane angle Inclinometer 12 Castor stem angle n a Fixed Distance between the brake blocks amp their TLE77 53 N engaged contact surfaces 3 Test dummy set up Value position Adjustable parameter Type of equipment ae Calculated seat to back angle Inclinometer hs Dummy size TLE133 Adult 115kg Dummy seat to back angle Inclinometer 8 5 RVA AIN jacm NATA NATA Accredited Laboratory No 2953 Page 9 of 12 N This document shall not be reproduced except in full Tester s Initials RP WW x a Accreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 J r ISO 7176 15 1996 Requirements for information disclosure documentation and labelling Accreditation No 2953 Clause Requirement Result 5 Requirements for disclosure of test information in manufacturer s specification sheets Specification sheet must contain the following a The model designation and or any other information that will uniquely identify the wheelchair Pass model b The mass of the test dummy used in the test Pass Either i the performance values listed in Annex A in the order and using the wording shown Pass c Or ii if the part of ISO 7176 specifies a method of disclosure that metho
17. pright Seat back position fore aft Back Forward 2 2 1 Wheels unlocked and the wheelchair in the least stable configuration Pass 2 2 2 Wheels locked and the wheelchair in the least stable configuration Pass 2 2 3 Wheels unlocked and the wheelchair in the most stable configuration Pass 2 2 4 Wheels locked and the wheelchair in the most stable configuration Pass 2 3 Test for rearward static stability with rear anti tip devices 2 3 1 Anti tip device in the least stable configuration Pass 2 3 2 Anti tip device in the most stable configuration Pass jacm NATA NATA Accredited Laboratory No 2953 Page 4 of 12 EENS This document shall not be reproduced except in full Tester s Initials RP WW Accreditation No 2953 ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM Job Number 491985 1 y r Clause in ISO 7176 1 1999 3 Result of Test Requirement Verification 2 4 Test for static stability in the sideways direction Adjustable wheelchair component Least stable Most stable Rear wheel position camber Narrowest track Widest track Castor attachment to frame fore aft Back Forward Castor attachment to frame inside outside Inside Outside Seat position fore aft Forward Back Seat position vertical High Low Seat position tilt Upright Back Seat back position recline Upright Back 2 4 1 Wheelchair in the least stable configuration
18. rts that have to be serviced by the manufacturer or an authorised service Pass facility in order to maintain any warranties and serviceability g iii Identification of any parts that can be removed and sent to the manufacturer distributor or Pass other party for repair g iv Identification of circumstances in which the manufacturer distributor or service agent should Pass undertake the repair g v A list of authorised service facilities Pass g vi Information on whether or not any replacement units are available NA g vii Packing and shipping instructions where necessary Pass 8 Permanent labelling 8 1 The following information to be marked in a permanent manner on the wheelchair a The name and address of the manufacturer Pass b The model designation and serial number Pass c The year of manufacture Pass d Any driving restrictions NA e Recommended maximum user mass Pass 8 2 Tyres to be marked with size Pass RVA ASN jiae wRA NATA NATA Accredited Laboratory No 2953 Page 11 of 12 ENN This document shall not be reproduced except in full Tester s Initials RP WW ISO 7176 1 1999 MANUAL WHEELCHAIRS STANDARD TEST FORM ye Job Number 491985 1 Information Disclosure Feature Min Max Feature Min Max Overall length with legrest 825 mm 825 mm Seat plane angle 12 0 n a Overall width 650 mm 650 mm Effective seat depth 415mm 415mm Folded length 750 mm 750 mm Effective seat width 400
Download Pdf Manuals
Related Search