HP® LASERJET P1102
Contents
1. signal is also placed on the magnetic roller sleeve This signal decreases the attraction of the toner to the magnetic roller sleeve and increases the repelling action of toner against the areas of the drum that was not exposed to the laser beam This AC potential improves the density and contrast of the toner on the printed page As the laser exposed areas of the OPC drum approach the magnetic roller the toner particles are attracted to the drums surface due to the opposite voltage potentials of the toner and laser exposed surface of the OPC drum Photosensitive Static charge eliminator Transfer roller In the fourth step Transfer Block the toner image is then transferred to the paper as it passes below the drum by the transfer charge roller which places a positive charge on the back of the paper This positive charge causes the negatively charged toner on the drum s surface to be attracted to the page The small diameter of the drum combined with the stiffness of the paper causes the paper to peel away from the drum In the fifth step also part of the transfer block the paper separates from the drum The static charge eliminator weakens the attractive forces between the negatively charged drum surface and the positively charged paper This prevents toner dropouts onto the paper at low temperatures and humidity and also prevents paper from wrapping around the drum UniNet www uninetimaging com 2010 UniNet Imaging In2. G INSTRUCTIONS 29 Replace the chip REPETITIVE DEFECT CHART OPC Drum 75mm Upper Fuser Film 57mm Lower Pressure Roller 56mm Transfer Roller 39mm Magnetic Roller 34mm PCR 2 mm RUNNING TEST PAGES Test pages must be run from the P1102 menu Access the Printer Preferences menu then Services and Information pages There are three test pages that can be selected The Demo Config and Supply Status Page RUNNING THE CLEANING PAGE The cleaning page for these machines can only be run from the Printer menu HP recommends that for best results a transparency be used If a transparency is not available user copier grade paper with a smooth surface 1 To run this page access the printer preferences 2 Click on DEVICE SETTINGS 3 In the Cleaning Page area press START 4 The cleaning cycle takes up to two full minutes The page will start and stop Do not turn the printer off until the cleaning page has finished printing UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com
3. HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET P1102 TONER CARTRIDGE uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE HP LASERJET P1102 SERIES TONER CARTRIDGE CE285A By Mike Josiah and the Technical Staff at UniNet In May 2010 Hewlett Packard released the LaserJet P1102 printer The HP P1102 series of laser printers are based on a 19ppm 400 x 600dpi Canon engine These cartridges use a chip that controls the toner low functions The CE285A is rated for 1 600 pages The printer itself has a very small foot print It s a nice small office home machine The memory is fixed and not expandable at SMB The recommended monthly volume is from 250 1 500 pages month These machines also have a new feature called Smart install in which the printer driver is built into the printer so no drivers need to be installed Just plug in the USB or Ethernet cable and you can start printing The printer when new comes with a starter cartridge that is rated for 700 pages at 5 coverage so
4. article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 19 When a seal becomes available remove the seal port plug and install the seal Bring the tail out through the seal porthole Install the plug 20 Install the left side end cap and screw Make sure the small contact piece is installed correctly on the end cap uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 21 Install the doctor blade and two screws 22 Install the magnetic roller black bushing side first Turn the roller until the keyed end locks in place 23 Install the gears as shown 24 Install the end cap and screws www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For addit
5. c All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS Fuser heater Fuser film Toner O Media Pressure roller In the sixth step the image is fused on to the paper by the fuser assembly which is comprised of the upper fixing film assembly and the lower fuser roller The paper passes between a heated upper fixing film assembly and a soft lower rubber roller The upper heated element then melts the toner into the paper The fixing film assembly consists of a Teflon sleeve with a ceramic heating element inside These fusers are a bit different in that they have a brush which has a DC Bias charge on it to help keep the film clean Cleaning blade yan Photosensitive drum In the seventh step the OPC drum is cleaned On average approximately 95 of the toner is transferred to the paper during the print cycle As the drum rotates during printing the remaining 5 of the toner is cleaned off the drum by the wiper blade It is then guided into the waste chamber by the recovery blade and stored in the waste chamber The eighth step is where the residual charge is eliminated Bo
6. drum 3 Replacement chip dedicated 4 Wiper blade 5 Doctor blade 6 Magnetic roller T Sealing strip 9 Cotton swabs 10 Isopropyl alcohol 11 Drum padding powder 12 Conductive grease TOOLS REQUIRED 1 Phillips head screwdriver 2 Small common screwdriver 3 Needle nose pliers 4 Jewelers screwdriver set HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 1 With the handle facing you remove the right side screw and end cap from the cartridge Be careful of the drum cover spring Remove it with the end cap in ALEEN si n 4 r Mijilitssiea j HIES H ra s b He P ia i iaa 2 With the pair of needle nose pliers release both the hopper tension springs www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sa
7. ere the toner image is developed on the drum by the developing section or supply chamber which contains the toner particles The toner is held to the magnetic roller sleeve by the stationary magnet inside the sleeve and a DC bias voltage supplied by the high voltage power supply This DC bias voltage is controlled by the printer density setting and causes either more or less toner to be attracted to the drum This in turn will either increase or decrease the print density Both the primary charge and magnetic roller DC Bias voltages are controlled by the printer density setting The amount of toner on the magnetic roller sleeve is also controlled by the rubber doctor blade which uses pressure to keep the amount of toner on the magnetic roller sleeve constant This blade also causes a static charge to build up on the toner which helps keep the coating of toner even and allows easy transfer to the OPC drum uniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS Blade Developing cylinder Photosensitive drum At the same time an AC
8. ional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 25 Place the drum waste hopper into the toner hopper Slide it over so the round hinge pins fit into their respective holes 26 Set the hopper tension springs back in place www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS a 27 With the drum cover spring as shown on the end cap install the end cap Lift up the tail of the spring to fit onto the hopper 28 Lift up the drum cover spring tail to fit as shown on the drum cover Install the screw into the cover www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURIN
9. le reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 3 Slide the waste drum section over to the left side Separate the two halves 4 On the waste drum section lift the drum up from the gear 5 Remove the PCR and clean with your standard PCR cleaner side Twist and remove from the hopper uniNnet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 6 Remove the two screws and the wiper blade T7 Clean out all the waste toner from the hopper Be careful not to damage the recovery blade located next to the wiper blade If this blade is bent in any way the cartridge will leak Make sure the wiper blade foam seals are clean uniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Una
10. nded to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 14 Remove the single screw and end from the opposite side 15 Remove the magnetic roller assembly Be careful of the bushings They are very fragile UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 16 Remove the doctor blade and two screws 17 Clean out all the remaining toner from the hopper Make sure the magnetic roller seals and the doctor blade seals are all clean 18 Fill the hopper with P1102 toner uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this
11. th the PCR and the laser unit are used for this The primary charge roller places an AC voltage across the drum surface and the laser unit s second beam erases and residual charges left on the drum This drum charge elimination is only turned on during the last rotation period of the drum The following figures show the differences from another newly released cartridge for the HP P1606 series of printers the CE278A cartridge Neither of these cartridges is compatible with the P1006 CB435A or P1505 CB436A They are all physically different uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com SUPPLIES REQUIRED 1 HP P1102 toner 2 New
12. upport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS Primary charging roller DC bias Photosensitive drum The image formation process consists of a series of steps in the first step the Primary Charge Roller PCR places a uniform negative DC Bias voltage on the OPC drum surface The amount of the negative DC Bias placed on the drum is controlled by the printer intensity setting This process is part of the Latent Image Formation Block Laser beam Photosensitive drum BD sensor Laser unit q Bs On Scanning mirror Scanner motor unit O isa Unexposed area Exposed area LASER CONTROL SIGNAL SCANNER MOTOR CONTROL SIGNAL BDI SIGNAL In the second step the laser beam is fired onto a rotating mirror called the scanner As the mirror rotates the beam reflects into a set of focusing lens The beam then strikes the OPC surface which neutralizes the negative charge on the drum and leaves a latent electrostatic image on the drum The laser unit actually fires two beams The service manual does not mention the second laser beam at all but at this point we are not sure if the second laser actually helps erase any residual charges on the drum or helps speed up the printing process We are leaning towards the second laser helping to erase any residual images as other recent Canon based engines also use the dual laser for this The third step Developing Block is wh
13. uthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 8 Coat the new cleaned wiper blade with your preferred 9 Install the cleaned PCR Place a small amount of conductive lubricant Install the wiper blade and two screws grease on to the black holder side of the shaft Just a small amount of grease is more than sufficient 10 Place another small amount of conductive grease on to 11 Install the new cleaned drum hub side first the metal drum axle Place the waste drum section aside uninet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techsupport uninetimaging com HP LASERJET P1102 CARTRIDGE REMANUFACTURING INSTRUCTIONS 12 On the toner supply chamber right side remove the two screws and end cap 13 Remove the gears from the hopper as shown Leave the large auger gear in place UniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are inte
14. your customers will be coming to you fairly quickly There are currently four printers based on this engine The P1102 P1102W M1130 and the M1212NF The new cartridge is a modified version of the older P1505 cartridge In fact many parts for the P1505 work in this new cartridge as well Cartridge troubleshooting as well as running test pages cleaning pages and some simple printer troubleshooting will be covered at the end of this article The theory for these cartridges is a little different from past versions so we have covered it here You don t have to know the theory to remanufacture cartridges but it sure helps if you have a problem Troubleshooting time can be dramatically reduced CARTRIDGE THEORY This figure gives a nice block diagram of the printing process lt Paper path lt t Rotational direction of the drum Electrostatic latent image formation bloc 2 Laser beam exposure 1 Primary charging ee Developing block I I Leecewweweeeceees SR eeeececaece i 1 I Photosensitive drum cleaning block ing block J uniNet www uninetimaging com 2010 UniNet Imaging Inc All trademark names and artwork are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information Unauthorized sale reproduction or distribution of this article is prohibited For additional support please contact techs
Download Pdf Manuals
Related Search