SB-4-043-R 120175 (GFC-502) Aluminum Gravity Feed
Contents
1. tight PARTS LIST GFC 502 GFC 404 K2 KGP 5 K5 KGP 12 K5 KGP 13 K5 FILLING WITH PAINT Fill the cup with paint to the full mark Do not overfill INSTALLING THE LID Place plastic lid on the top of the cup and push in the center of the lid to assemble lid Fold vent cap and push onto center portion of lid if vent cap is not already assembled CLEANING Note For routine cleaning it is not nec essary to remove cup from gun Do not remove washer 4 from gun If washer 4 is removed it must be replaced CAUTION Do not soak the lid in solvent for extended periods of time Doing so could cause cup lid sealing problems and leakage Cup Drawings Drain Hole A wi Cup Fitting per X ESA A Cup Gasket YL 4 4A Gun Body Metal Gravity Feed Cup 1Liter Disposable Lid Kit Kit of 2 Filter Kit Kit of 5 Cup Gasket White Kit of 5 EEE eee Part No Description 1 2 3 4 4A Cup Gasket Blue Kit of 5 The cup lid is designed to be disposable but may be cleaned and reused if slightly contaminated with overspray If lid be comes tight or does not fit it is due to extended soaking in solvent Let lid air dry overnight and the lid should return to its original size and fit Remove lid and properly dispose of any excess paint Pour in a small amount of clean solvent The amount will vary with different coatings and solvents Rein stall lid Shake cup to wash down2. DEVILBISS 120175 GFC 502 SERVICE BULLETIN SB 4 043 R Replaces SB 4 043 O Aluminum Gravity Feed Cup Important Before using this equipment read all safety precautions and instruc tions Keep for future use Halogenated Hydrocarbon Sol vents for example 1 1 1 trichloroethane and methylene chloride can react with the aluminum in this cup and cause an explosion hazard Read the data sheet for the material you intend to spray Do not use spray materials containing these solvents with this cup DESCRIPTION 120175 GFC 502 1 Liter Cup This cup is designed to be used with or without the DeVilbiss disposable cup liner The cup liner allows painting in any position and simplifies clean up The cup is constructed from durable aluminum to provide trouble free op eration The cup insert is electroless nickel plated brass The disposable cup lid is recyclable and is constructed with recycled polyethylene The lid has a unique drip check to prevent paint from dripping out of the vent in the lid ASSEMBLY OF CUP TO GUN 1 Remove one of the cup gaskets 4 White for GFG and GFHV guns 4A Blue for CVI GTI FLG M1 G and Compact guns fromthe poly bag 2 Place this cup gasket in the fluid inlet of the gun body See Cup Drawing 3 Store remaining cup gasket in a safe place for future use 4 Place filter 3 in cup outlet at this time if desired See Cup Drawing 5 Assemblecupto gun andtighten hand
3. the inside surfaces Hold lid while shaking to preventlid from coming off Pull triggerto allow some solvent to be flushed through gun Remove lid and pour out dirty solvent Add a small amount of clean solvent and repeat procedure Wipe exterior of lid with a clean cloth and clean solvent If a paint filter was used in the bottom of the cup outlet it should be removed and cleaned or replaced at this time Dispose of used cup lid if contaminated and replace with new Full Mark D 3 For GFG amp GFHV guns White 4 For CVI GTI FLG M1 G 4A PRI amp GFG PLUS guns Blue Page 2 SB 4 043 R ACCESSORIES CA PROP PROP 65 WARNING WARNING This product contains chemicals OMX 70 K48 PAINT CUP LINER KIT 65 known to the State of California to cause cancer Not for use with GFC 503 cups and birth defects or other reproductive harm Allows quick and easy clean up Consists of 1 Piercing Tool 48 Disposable Liners 48 Drain Bushings WARRANTY This product is covered by DeVilbiss 1 Year Limited Warranty DeVilbiss Sales and Service www devilbiss com D VIL BISS U S A Canada Customer Service Toll Free Customer Service E A 195 Internationale Blvd slag a support Glendale Heights IL 60139 630 237 5000 Toll Free Fax 888 246 5732 8 13 2013 DeVilbiss All rights reserved Printed in U S A
Download Pdf Manuals
Related Search