- S&S Cycle
Contents
1. See Notes on Intermediate and High Speed Jetting below Notes on Intermediate and High Speed Jetting Carburetor jetting and spark plug color While spark plug color may be used to help determine carburetor jetting S amp S recommends that our instructions be used as primary jetting guide and that plug color indications be used only as secondary aid We have found that different brands of gasoline gasoline additives engine heat due to ignition timing and type of plugs and heat range used distort plug color drastically making plug reading difficult for average tuner Also new plugs usually require road test of 10 miles or more to properly develop color which means that quarter mile tests may not be long enough and hence not always a good indication of carb jetting It is best to use proven spark plug combinations and to consult spark plug manufacturer if you have questions If one desires to become more proficient at plug reading Champion Racing Division has a very informative booklet which may be helpful If bike is used exclusively on drag strip where engine temperatures vary slightly richer jets may be necessary to gain best performance Larger jets or richer mixtures will enable one to run colder engine which is sometimes desirable This is best determined by experimentation with particular engine to be used Cams and exhaust systems can make some engines difficult to carburate We have found that certain cams and exhaus2. adjusters to put more freeplay in cables NOTE Throttle must not bind and must snap shut to fully closed position when released A WARNING If throttle does not return to fully closed position when released it may inadvertently stick open possibly causing loss of control of motorcycle and personal injury to you or others E Bolt carb to intake manifold using two 3 16 x 1 socket cap screws provided in kit Knucklehead panhead and 1983 84 kits come with one 1 screw and one 1 1 4 screw The 1 1 4 screw must go in bottom hole and is longer to compensate for thickness of mounting bracket part 16 0096 or 16 0471 A CAUTION If incorrect length mounting screws are used in carburetor mounting holes screws may bottom in mounting hole or contact carb bowl causing damage to carb body and or carb bowl F Recheck throttle to be sure it opens and closes freely See step D NOTE Throttle must not bind and must snap shut to fully closed position when released A WARNING If throttle does not return to fully closed position when released it may inadvertently stick open possibly causing loss of control of motorcycle and personal injury to you or others G Apply thin coating of oil to fuel inlet fitting and slip end of fuel line with 90 bend on fitting Clamp in place Slip stock Harley Davidson protective fuel line covering over fuel line if equipped and position where contact with other engine parts might take place
3. 0471 Manifold O ring Evolution 16 0236 Manifold flange all Evolution Ree EE 16 0232 RG al Ee th ape eae NEE 16 0233 Support bracket screw 5 16 18x1 10 Pack 50 0155 Manifold Evolution 1 7 8 for Sportster models stock cylinder length 16 1600 1 78 for Evolution stock cylinder length 16 1608 Support bracket panhead 16 0096 Flatwasher 38 special 10 Pack 50 7075 Air horn includes 3 50 0071 17 0042 Air cleaner assembly for all engines Does not include mounting brackets 17 0099 Air horn screw 10 Pack 00005 50 0195 Air cleaner cover screw 10 Pack 50 0094 Air cleaner cover 20 00eeeee ee eeees 17 0078 Air cleaner element 17 0079 Air cleaner backing plate 17 0080 Air cleaner support bracket 1957 85 Sportster model 17 0093 Vent hose connecter nipple 50 8111 Vent hose 38 IDxvpn 000 e eee 17 0113 90 elbow fitting 50 8110 Support bracket bolt 14 28 x 78 10 Pack 50 0193 Flatwasher 14 10 Pack 00005 50 7074 Air cleaner backplate screw 10 Pack 50 0096 Air cleaner gasket 17 0196 Allen head plug L 21 eee eee 50 8331 Mounting hole plug 10 Pack 50 8322 Support bracket locknut 14 28 x 78 10 Pack Zeck a eg et Ee ite ates 50 5015 Air cleaner support bracket 1
4. area in carburetor body 4 Readjust engine rpm to idle at approximately 950 1000 rpm 5 After engine and oil have reached normal operating temperature repeat steps 3 and 4 NOTE Whenever intermediate jet change is made idle mixture screw must be readjusted Troubleshooting Tips engine will not idle Improper idle mixture and or engine rpm setting 2 Intake manifold air leak 3 Sticky timing automatic advance mechanism or other ignition problem 4 Foreign material in air and or gas passageway in carb causing flow restriction to idle intermediate circuit Clear holes with forced air A CAUTION Do not use wires or drills to clear holes If sizes are altered air fuel ratios of idle and intermediate systems will be changed resulting in poor performance and irreversible damage to carburetor body and intermediate jet A WARNING Compressed air and particles dislodged using compressed air are harmful to eyes and body Wear protective goggles when using compressed air and always direct air stream away from body parts such as hands and eyes and other people near you ur Enrichment device plunger not sealed causing excessively rich mixture Be sure device is fully disengaged in down position allowing plunger to bottom out and seal passageway CURE Lift and release plunger several times letting it snap to closed position to fully seat and seal against carb body Intermediate System Intermediate rang
5. bracket and shims in place with 516 18 x 1 mounting bolts and 5 16 flat and lock washers Snug all nuts and bolts Do not final tighten K Final tighten manifold mounting clamps and or mounting flange bolts L Remove air cleaner backplate from carburetor 5 Install Carb A Determine length of throttle cables required and shorten if necessary If outer cables are shortened inner cables must shortened also Be sure to determine proper length and resolder last 1 1 2 of inner cable before cutting This will insure cable strands do not separate If cable lengths are correct and are equipped with ball or barrel fittings last 1 1 2 of inner cables must be soldered before ends are cut off Apply light coat of lubrication to inner cables before reassembling NOTE Consult Harley Davidson service manual for proper throttle disassembly and reassembly procedures B Thread opening side throttle cable through upper throttle cable housing boss and throttle cable clamp on throttle arm C Repeat step B for closing side throttle cable Cable with larger diameter outer housing is used to close throttle and should be positioned in lower boss on carburetor body D Adjust throttle cable adjusters to remove excessive freeplay and test throttle to be sure it opens and closes freely Turn handlebars to extreme left and open and close throttle then turn bars to extreme right and check throttle If throttle binds loosen cable freeplay
6. course of action A part that is suspect of being defective must not be replaced by a Dealer without prior authorization from S amp S If it is deemed necessary for S amp S to make an evaluation to determine whether the part was defective a return authorization number must be obtained from S amp S The parts must be packaged properly so as to not cause further damage and be returned prepaid to S amp S with a copy of the original invoice of purchase and a detailed letter outlining the nature of the problem how the part was used and the circumstances at the time of failure If after an evaluation has been made by S amp S and the part was found to be defective repair replacement or refund will be granted ADDITIONAL WARRANTY PROVISIONS 1 S amp S shall have no obligation in the event an S amp S part is modified by any other person or organization 2 S amp S shall have no obligation if an S amp S part becomes defective in whole or in part as a result of improper installation improper maintenance improper use abnormal operation or any other misuse or mistreatment of the S amp S part 3 S amp S shall not be liable for any consequential or incidental damages resulting from the failure of an S amp S part the breach of any warranties the failure to deliver delay in delivery delivery in non conforming condition or for any other breach of contract or duty between S amp S and a customer 4 S amp S parts are designed exclusively for
7. 32 below bowl gasket surface Float must not contact bowl gasket When motorcycle is not running fuel shutoff valve should always be turned off to prevent possible leakage should needle and seat not work properly Ian air horn is desired for drag racing use S amp S part 17 0042 Be sure to shroud bowl vent f you feel you have marginal fuel delivery through your stock petcock S amp S recommends you try Pingel petcock part 19 0453 for big twins or 19 0454 for Sportster models requires nut 19 0455 for both Tests conducted at S amp S have shown Pingle petcocks to provide more than adequate fuel supply If you require an in line fuel filter use Pingel L1BLK1BLK40G if room permits filter is 3 long and anodized black or S1P1P40G if room doesn t permit filter is 1 122 long and polished aluminum As a convenience to our customers S amp S stocks these Pingel parts S amp S part 19 0453 Pingel petcock 5211C for big twins S amp S part 19 0454 Pingel petcock 31 6011 for Sportster models S amp S part 19 0455 Pingel nut 33 2001 S amp S part 19 0457 Small Pingel filter 51P1P40G 10 IMPORTANT NOTE We at S amp S feel we have designed and manufactured a quality carburetor and will stand behind this product If you have questions or problems refer to the instruction sheet Answers to nearly all your questions can be found in the instructions If you still have a problem you may call for te
8. 984 91 Evolution amp 1986 90 Sportster models 17 0312 Support bracket screw 516 18 x 134 10 Pack 0 0008 50 0234 516 18 x 11 2 10 Pack 008 50 0196 516 18 x 11 4 10 Pack 2 000 50 0148 Lockwasher 5 16 10 Pack 50 7077 Support bracket 10 Pack 50 7075 74 75 76 77 78 Shim 516 x 020 10 Pack 0 00 eee 50 7107 516 x 030 10 Pack 2 00 eee 50 7070 516 x 040 10 Pack 02 0 00 eee 50 7068 5 16 x 100 5Pack c ee eee eee 50 7062 16 x 125 5 Pack cee eee eee eee 50 7066 Shim 16 x 250 5 Pack cee eee eee eee 50 7067 516 x 550 Gbacki eee eeee 50 7065 Shim kit includes 2 50 7038 50 7039 50 7040 50 7041 amp 4 50 7042 17 0314 Shim kit includes 2 50 7043 amp 2 SO 2045 17 0313 Air cleaner support bracket 66 82 shovelhead 00000e ee eae 17 0092 11 Because every industry has a leader
9. Instruction 51 1006 4 24 06 Copyright 1998 1999 2002 2006 by S amp S Cycle Inc Phone 608 627 1497 Technical Service Phone 608 627 TECH 8324 Technical Service Email sstech sscycle com Website www sscycle com All rights reserved Printed in the U S A SES Cycle Tac 235 Causeway Blvd La Crosse Wisconsin 54603 Fax 608 627 1488 Because every industry has a leader Installation and Jetting Instructions for S amp S Super B Series Carburetor DISCLAIMER S amp S parts are designed for high performance off road racing applications and are intended for the very experienced rider only The installation of S amp S parts may void or adversely effect your factory warranty In addition such installation and use may violate certain federal state and local laws rules and ordinances as well as other laws when used on motor vehicles used on public highways especially in states where pollution laws may apply Always check federal state and local laws before modifying your motorcycle It is the sole and exclusive responsibility of the user to determine the suitability of the product for his or her use and the user shall assume all legal personal injury risk and liability and all other obligations duties and risks associated therewith The words Harley Harley Davidson H D Sportster Evolution and all H D part numbers and model designations are used in reference only S amp S Cycle is not associated w
10. On early models equipped with bottom manifold screw wire fuel line support guide use guide whenever possible Connect fuel line to gas tank petcock using clamp provided A WARNING Fuel line must be clamped securely and not contact any hot surfaces such as exhaust pipes where it could melt and catch fire 6 Install Air Cleaner Backplate A Mount air cleaner backplate on carb using three 1 4 20 x 3 4 screw washer assemblies through holes C See Figure A B 1966 to 1982 shovelhead and ironhead Sportster models Bolt bracket to air cleaner backplate through hole B See Figure A Use 1 4 bolt flatwasher and locknut provided and snug all mounting bracket bolts Final tighten all mounting bracket bolts C Harley Davidson 1984 to 1992 Evolution and Sportster models to 1990 Bolt air cleaner backplate bracket to cylinder heads with 5 16 18 bolts flatwashers and lock washers Fill gap between cylinder heads and mounting bracket with shims as previously determined in manifold installation step D Shovelhead and Sportster models 1980 to 1985 and all Evolution Connect crankcase breather hose to air cleaner backplate hose fitting 7 Reassemble Anything That Was Disassembled for Installation and Final Check Installation A Check carb to manifold mounting bolts B Check carb to air cleaner backplate mounting screws C Check carb mounting bracket to head or to tappet block mounting bolts an
11. Whenever intermediate jet change is made idle mixture screw must be readjusted Gas mileage and throttling characteristics may also be determined by personal riding habits Snapping throttle open in lower rpm ranges is inefficient and uneconomical because intermediate system is bypassed When intermediate system is bypassed engine momentarily goes lean from lack of fuel from intermediate then rich from excessive fuel from main In effect engine uses more fuel than it should Engine will respond better and be more efficient if throttle is rolled on and intermediate has time to properly engage High Speed Circuit or Main Jet S amp S Super B Jetting Chart Engine Stock CH Stock Big Twin Strokers 84 or Displacement Strokers Mild Strokers Larger Idle Mixture 1 1 4 to 1 3 4 1 1 4 to 1 3 4 1 1 4 to 1 3 4 Screw Setting turns turns turns 265 to 032 0295 to 033 031 to 036 wein 062 to 070 068 to 076 072 or larger Intermediate Main Jet Picture 2 High speed circuit begins around 3000 3500 rpm or 55 60 mph and operates to maximum attainable speed Main jet part 11 7200 is reached by removing bowl plug part 11 2090 NOTE S amp S has special main jet tool part 53 0452 which is handy for changing main jets Size of metering hole in main jet in thousandths of an inch is stamped on end of jet Size of main jet installed in new carburetor from S amp S is indicated on tag attached to carb and o
12. are harmful to eyes and body Wear protective goggles when using compressed air and always direct air stream away from body parts such as hands and eyes and other people near you Gei Improper diagnosis of rich or lean mixture condition If engine backfires in carb this usually indicates lean condition and engine must be reprimed If there is no response after three kicks or if engine pops in exhaust pipes it usually means mixture is too rich Leave switch on and slowly open throttle 14 turn with each successive kick until engine fires Adjusting Carburetor Idle Circuit Idle mixture screw part 11 2354 regulates air fuel mixture at idle speeds Throttle stop engine rpm adjustment screw is located on throttle arm part 11 2148 See Picture 1 S amp S adjusts both screws during assembly to settings that should work for initial start up after installation 1 Start engine and run until slightly warm approximately 1 to 2 minutes 2 Initially adjust engine rpm to idle at approximately 950 1000 rpm 3 Turn idle mixture screw part 11 2354 clockwise leaning mixture until engine starts to die Next turn screw counterclockwise richening mixture until engine starts to die When screw is positioned about halfway between these points or about 14 to 1 2 turn out from lean side of adjustment range it is set correctly A CAUTION Closing idle mixture screw too tightly may cause irreversible damage to needle and seating
13. bleech en dE weed man 11 2095 20 Seat Styles BE Ae EE AE 11 2065 Style C threaded seat not available See 80 21 Bowlplug 000 cece eee 11 2090 22 Bowl screw 10 Pack 00005 50 0063 23 Gas inlet fitting 90 not available See 80 Float just below gasket surface approx 1 32 Spring in needle fully compressed Figure D 32 35 36 37 38 39 41 42 43 44 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 Knucklehead panhead manifold 1 78 for O ring style heads 16 1100 1 spacer 1 7 8 00 kc eee 16 0057 Manifold screw E ELE Bake Oe E 50 0186 1 A 10 Pack sie c itt ales 50 0177 SE PACK eras ee 50 0185 SL UE eerst Su ocean ees es 50 0180 O ring for O ring manifold 16 0237 Band for rubberband manifold 16 0238 Manifold shovelhead amp Harley Davidson ironhead Sportster 1 78 O ring style stock length 16 1200 1 78 Rubberband style stock length 16 1300 1 7 8 Rubberband style w VOES ignition stock Jengoth cece a ea 16 1400 Manifold clamp O ring style 16 0230 Rubberband style 16 0231 Lock nut 5 16 18 10 Pack 50 5050 Flat washer 5 16 x 116 10 Pack 50 7069 Adjustable support bracket 16
14. chnical help at 608 627 TECH 8324 S amp S also has a complete carburetor repair and or rebuilding service where you can get quality work at a fair price If you are not properly equipped to take this carburetor apart and repair it and do not have a qualified local repair shop available we recommend you call for a return authorization number and send it to us with a detailed note outlining any problems you may have and any repairs you want performed so it can be serviced correctly Super B Carburetor Replacement Parts 1 Throttle return spring 11 2082 2 Throttle plate screw 10 Pack 50 0064 3 Throttle shaft includes 2 50 0029 11 2083 4 Throttle shaft bushing for repair only 11 2134 5 Enrichment device 11 2084 6 lui VEER 11 2081 7 Idle mixture screw 11 2354 8 Idle mixture screw spring 5 11 2052 9 O ring 1 7 8 10 Pack 2 005 50 8101 10 Throttle plate 1 78 2 2005 11 2055 11 Throttle arm assembly two cable type 11 2148 12 Intermediate jet state size See jet section 13 Main discharge tube 5 2 11 2085 14 Main jet state size See jet section 15 Bowl gasket 0 cece cece eens 11 2086 16 Float Style G rege SE dE ele GE Ee 11 2187 EE N A 17 Float retaining pin 0 005 11 2069 18 Bowl SWIG gu hei ela ae E ge 11 2188 EE N A 19 Needle KOR EE 11 2195
15. d air cleaner backplate to heads mounting bolts D Check fuel line connections and routing E Check vacuum operated advance ignition connections if applicable F Check crankcase to air cleaner backplate vent hose connections if applicable G Test throttle to be sure it opens and closes freely Turn handlebars to extreme left and open and close throttle then turn bars to extreme right and check throttle NOTE Throttle must not bind and must snap shut to fully closed position when released A WARNING If throttle does not return to fully closed position when released it may inadvertently stick open possibly causing loss of control of motorcycle and personal injury to you or others H Reassemble anything that was disassembled for installation Consult your Harley Davidson service manual for installation of parts not covered in these instructions 8 Bolt on Air Cleaner Cover A Check fuel needle and seat assembly to be sure it works properly Fill gas tank with just enough fuel to test system Lean motorcycle over towards carburetor side turn on fuel petcock and wait 20 seconds If gas runs out end of carb turn off petcock and check needle and seat NOTE Fuel needle and seat assembly must completely shut off fuel supply entering bowl Fuel inlet fitting to bowl sealing area and or fuel line connections must not leak A CAUTION Unwarranted gasoline leaking by inlet needle may flood engine causing damage to co
16. e and irreversible damage to carburetor body and intermediate jet A WARNING Compressed air and particles dislodged using compressed air are harmful to eyes and body Wear protective goggles when using compressed air and always direct air stream away from body parts such as hands and eyes and other people near you 5 No air cleaner used or air cleaner used is brand other than S amp S Some air cleaner designs restrict air flow so that carb cannot draw air freely as needed Also other air cleaners may obstruct bowl vent hole on inlet end of carb and change bowl air pressure NOTE Bowl vent hole passageway leads to cavity above fuel in bowl and is designed to equalize bow pressure and atmospheric pressure If high or low bowl pressure relative to atmospheric pressure develops engine may run erratically 6 Air horn used without carburetor body shrouding bowl vent on end of NOTE Bowl vent should be shrouded to insure uniform atmospheric air pressure between cavity above fuel level in bowl and area outside carburetor body If high or low bowl pressure relative to atmospheric pressure develops engine may run erratically 7 Valve train defect bad valves sticky valves bad or broken springs improper clearances for high lift cam or defective camshaft with improper valve timing Bevels must be at angles shown by arrows when installing plate Figure C 8 9 Too much gear not enough horsepower to pull gearing
17. e is used most often under normal riding conditions and begins right off idle and operates up to approximately 3000 3500 rpm or 50 to 60 mph depending on gearing Therefore close attention must be paid to jetting intermediate range to achieve optimum performance and best gas mileage Intermediate jet part 11 7100 is reached by removing float bowl assembly See Picture 2 Actual size of intermediate jet installed in carburetor is indicated on tag attached to carb and or on printed label on carburetor packing box Keep this information handy for future reference Road test bike being sure to ride it far enough to bring engine and oil to normal operating temperature Re check idle mixture adjustments to be sure settings are correct with fully hot engine Check throttling characteristics by slowly rolling throttle on after maintaining steady speed This should be done at several rpm levels or speeds of 30 40 and 50 mph If popping or spitting backfiring occurs in air cleaner this indicates lean condition and intermediate jet must be changed to next larger size size is stamped on end or side of jet Change jet accordingly and repeat road test Smallest intermediate jet that eliminates this condition should provide best gas mileage N y gt A NOTES on Intermediate Jetting See Notes on Intermediate and High Speed Jetting at end of High Speed Circuit or Main Jet section of these instructions
18. etcock NOTE When motorcycle is not running fuel shutoff valve should always be turned off to prevent possible leakage should needle and seat not work properly A CAUTION Unwarranted gasoline leaking by inlet needle may flood engine causing damage to components A WARNING Unwarranted gasoline leaking past inlet needle may flood engine and overflow on surrounding area creating fire hazard 2 Turn on ignition 3 With throttle closed kick engine through or engage electric starter 4 If engine fails to start immediately open throttle slightly and continue to kick or engage starter until engine fires Troubleshooting Tips engine will not start 1 Fuel supply empty 2 Weak or no spark discharged battery or faulty magneto NOTE We do not recommend use of magnetos as magneto in poor condition and or improperly serviced can adversely affect starting conditions 3 Plug gap too wide we use 022 to 025 plug gap on point type ignition engines 4 Improper ignition timing 5 Tight tappet adjustment 6 Improper idle mixture and or engine rpm setting See Adjusting Carburetor Idle Circuit 7 Enrichment device well feed hole in bowl plugged Clear hole with forced air A CAUTION Do not use wire or drill to clear hole If size is altered starting system will be changed resulting in irreversible damage to carburetor bowl A WARNING Compressed air and particles dislodged using compressed air
19. etween tappet blocks and bolt bracket part 16 0471 in place to connect bottom carb manifold mounting hole to crankcases F lronhead Sportster models Bolt bracket part 17 0093 to front tappet block using 5 16 18 x 114 bolt 5 16 flatwasher and 5 16 lockwasher provided in kit Do not tighten End of bracket with sharp bend goes toward tappet block G Bolt carb to intake manifold Panhead and 1983 84 shovelhead mounting bolts measure 1 and 1 14 long 1 14 bolt goes in bottom hole Snug mounting bolts Do not final tighten A CAUTION If incorrect length mounting screws are used in carburetor mounting holes screws may bottom in mounting hole or contact carb bowl causing damage to carb body and or carb bowl H All engines except panhead and shovelhead 1983 to 1984 Install air cleaner backplate using three V 4 20 x 3 4 screw washer assemblies L 1966 to 1982 shovelhead and all ironhead Sportster models Bolt bracket to air cleaner backplate through hole B See Figure A Use 14 flatwasher and locknut provided and snug all mounting bracket bolts J Harley Davidson 1984 to 1992 Evolution and Sportster models 1986 to 1990 Bolt bracket part 17 0312 to air cleaner backplate through holes D using two 14 28 x 78 bolts two 14 28 nuts and V4 flatwashers provided Fill gap between bracket and cylinder heads using shims provided in S amp S shim kit part 17 0314 Hold backplate
20. f throttle arm part 11 2148 is removed from throttle shaft it must be reinstalled in wide open position with throttle plate part 11 2055 at 90 to the fully closed position See Figure B Throttle plate part 11 2055 should be checked annually for signs of wear Replace if necessary If carb body needs repair use S amp S repair kit part 11 2903 11 2914 or 11 2909 If throttle plate is removed be sure to reinstall it correctly See Figure C Edges of plate must fit flat against carb throat To insure proper seal in needle and seat assembly float hinge needle lift and needle must work freely and must not bind If problem is suspected remove bowl and check float movement If obvious misalignment binding or sticking occurs remove and straighten and reinstall to attain free movement Reset float level and double check for free movement Float must not contact bowl gasket Normal float setting is 1 32 and should be measured at end of float opposite needle and seat assembly To check this measurement turn bowl upside down and measure from bowl gasket surface up to float On rubber mounted engines set float where it just misses bowl gasket part 11 2086 when fuel inlet needle is fully closed and spring in needle is compressed See Figure D To check remove bowl and raise float until needle is in closed position and spring in top of needle is compressed Highest part of float should be slightly approximately 1
21. ith Harley Davidson Inc SAFE INSTALLATION AND OPERATION RULES Before installing your new S amp S part it is your responsibility to read and follow the installation and maintenance procedures in these instructions and follow the basic rules below for your personal safety Gasoline is extremely flammable and explosive under certain conditions and toxic when inhaled Do not smoke Perform installation in a well ventilated area away from open flames or sparks If motorcycle has been running wait until engine and exhaust pipes have cooled down to avoid getting burned before performing any installation steps Before performing any installation steps disconnect battery to eliminate potential sparks and inadvertent engagement of starter while working on electrical components Read instructions thoroughly and carefully so all procedures are completely understood before performing any installation steps Contact S amp S with any questions you may have if any steps are unclear or any abnormalities occur during installation or operation of motorcycle with a S amp S part on it Consult an appropriate service manual for your motorcycle for correct disassembly and reassembly procedures for any parts that need to be removed to facilitate installation Use good judgement when performing installation and operating motorcycle Good judgement begins with a clear head Don t let alcohol drugs or fatigue impair your judgement Start installa
22. mponents A WARNING Unwarranted gasoline leaks at fuel line connections and or past inlet needle may flood engine and overflow on surrounding area creating fire hazard B If needle and seat assembly works properly install element and air cleaner cover using three 14 20 x 1 mounting screws C Fill gas tank Carb Operation This carburetor does not have conventional choke Instead a mixture enrichment device part 11 2084 is used for starting This device utilizes separate air and fuel pickup passageways This device is engaged by raising the lever on top left side of carburetor and turning it slightly See Picture 1 Enrichment Device NOTES Enrichment pickup tube located directly below fast idle plunger is pressed into carburetor body and must not be removed CAUTION Removal of enrichment fast idle pickup tube from carburetor body may alter hole size in carb body and cause irreversible damage to carburetor Enrichment device may be removed for cleaning purposes but must not be disassembled any further Cold Starts 1 Open fuel petcock NOTE When motorcycle is not running fuel shutoff valve should always be turned off to prevent possible leakage should needle and seat not work properly A CAUTION Unwarranted gasoline leaking by inlet needle may flood engine causing damage to components A WARNING Unwarranted gasoline leaking past inlet needle may flood engine and overflow on surrounding a
23. ocal laws before modifying your motorcycle It is the sole and exclusive responsibility of the user to determine the suitability of the product for his or her use and the user shall assume all legal personal injury risk and liability and all other obligations duties and risks associated therewith Chrome Plating the Carburetor NOTE S amp S does not recommend chrome plating the Super B carburetor Proper preparation to achieve a good chrome finish requires polishing using buffing compounds These materials invariably plug air and or fuel passageways and feed holes regardless of the precautions taken A CAUTION Plugged passageways and feed holes and the polishing and chrome plating processes can alter operating tolerances machined into the parts in critical areas Additionally pieces of chrome may break off and plug a passageway which could potentially affect the fuel mixture resulting in damage to the engine S amp S voids any warranty if the carb body and or bowl is polished chrome plated or altered in any way Kit Contents Each complete carb kit includes One S amp S Super B gas carburetor One S amp S teardrop air cleaner assembly One manifold Mounting hardware Fuel line and clamps Two extra main jets One extra intermediate jet Voes tubing when applicable Installation and jetting instructions Throttle Requirements NOTE S amp S Super B carburetor requires the use of a two cable pull open pull closed thro
24. r on printed label on carburetor packing box Keep this information handy for future reference Main jet size is best determined by testing at drag strip because maximum miles per hour and rpm are best indicators of actual horsepower engine is developing S amp S recommends that high speed jetting be done at drag strip Dragstrip Procedure 1 Warm up engine enough to begin testing 2 Make run noting engine rpm and final speed 3 Increase or richen main jet size 004 larger and make second run Again note rpm and final speed 4 Continue procedure until mph falls off 5 Decrease or lean main jet size by 002 to gain best maximum rpm and mph When making runs do not strive for ET s but for consistent miles per hour Street Procedure S amp S uses what we call RPMing method to determine correct main jet size Hard acceleration is evaluated up to the rom where horsepower peaks and begins to taper off and gear shift occurs Main jet that makes engine accelerate strongest or rpm through gears quickest is correct 1 Warm engine to operating temperature 2 Accelerate rapidly through gears noting how quickly and smoothly engine reaches rpm level where pull of engine begins to fade and gear shift occurs 3 If engine backfires in carburetor and sputters or breaks up and or dies during acceleration increase or richen main jet size 004 larger and road test again Note engine smoothness and how easily engine reache
25. rea creating fire hazard 2 Pull enrichment device handle part 11 0084 to raised position See Picture 1 3 With throttle closed kick engine through three times Electric start models go to step 4 and engage electric starter For colder weather 50 and below or for engines with long duration cams it may be necessary to prime engine several additional kicks Low compression and or cams with long duration and extreme overlap may reduce cranking compression to where intake vacuum is low Low vacuum reduces draw through enrichment device making it difficult to get a sufficient prime If this appears to be the case close butterfly completely by turning engine rpm adjustment screw on throttle arm part 11 2148 one turn This will force all intake vacuum to draw through enrichment device during priming After initial startup turn rpm screw to original idle position NOTE If throttle is opened during priming enrichment device will not provide a rich enough starting mixture A Turn on ignition With throttle closed or slightly cracked kick engine through If engine fails to start immediately slowly crack throttle just enough to barely open butterfly and continue to kick or engage starter until engine fires After engine starts leave enrichment device on until engine has warmed sufficiently If necessary jockey throttle slightly to keep engine running Motorcycle may now be ridden Vi EA Hot Starts 1 Open fuel p
26. retor and air cleaner assembly or air horn if used rigidly to engine A CAUTION An improperly mounted carburetor could come loose from engine resulting in air leaks poor performance and damage to carburetor or other components Incorrect combinations of mounting hardware may cause some mounting bolts to bottom out in holes or inadvertently contact other parts possibly causing damage to one or more engine and or carburetor components A WARNING If motorcycle were to fall over or sustain damage in a collision or rider fall down an improperly mounted carburetor could break free causing an unwarranted release of gasoline to flood surrounding area creating a fire hazard and potential personal injury to you or others A Clean intake ports on cylinder heads to insure proper manifold to head seal B Install intake manifold provided Point vacuum advance fitting upward if it is equipped with one Do not tighten manifold clamps or flange bolts C Pans Loosen center crankcase stud nut between tappet blocks and bolt bracket part 16 0096 in place to connect bottom carb manifold mounting hole to crankcases Figure A D Shovelhead 1966 to 1982 Bolt bracket part 17 0092 to rear of front rocker cover using 5 16 18 x 58 bolt 5 16 flatwasher and 5 16 lockwasher provided in kit Do not tighten End of bracket with sharp bend goes toward rocker cover E Shovelhead 1983 to 1984 Loosen center crankcase stud nut b
27. s rpm level where gear shift occurs 4 If engine runs flat and sluggish or blubbers or will not take throttle decrease or lean main jet size 004 smaller and road test again Note engine smoothness and how easily engine reaches rpm level where gear shift occurs 5 Continue changing main jets until one is selected that makes engine accelerate or rpm through gears most quickly and smoothly Our experience has taught us that a jet about 006 smaller leaner than correct one will make engine break up and quit A jet about 006 larger richer will make engine blubber and miss Troubleshooting Tips for Intermediate amp High Speeds Engine will not run at steady speed or rpm 1 Restriction in fuel supply system gas tank vent plugged stock gas petcock too small Arrow 1 Throttle plate horizontal Arrow 2 Throttle arm against stop Arrow 3 Throttle arm set screw Figure B 2 Faulty ignition system fouled plugs worn points defective coil or solid state module improper ignition timing 3 Incorrect intermediate and or high speed jetting See Adjusting Carb Intermediate System and High Speed Circuit or Main Jet 4 Foreign material in air and or gas passageway in carb causing flow restriction Clear holes with forced air A CAUTION Do not use wires or drills to clear holes If sizes are altered air fuel ratios of idle and intermediate systems will be changed resulting in poor performanc
28. screw setting Turn screw See Picture 1 counterclockwise until it no longer contacts carb body Next turn it clockwise until it just recontacts body Then continue turning additional 1 2 turn clockwise slightly opening throttle plate part 11 2055 3 Prepare Air Cleaner Backplate A Knucklehead panhead 1955 to 1965 Thread plugs part 50 8331 into holes A and B in air cleaner backplate See Figure A B Shovelhead 1966 to 1979 and ironhead Sportster models 1957 to 1979 Press plugs part 50 8313 into holes D in air cleaner backplate See Figure A C Shovelhead 1980 to 1984 and 1980 to 1985 Sportster models Screw crankcase breather vent elbow fitting part 50 8110 into hole A in air cleaner backplate in Figure A On 1983 and 1984 shovelhead thread plug part 50 8331 into hole B Enrichment Device get Picture 1 D 1984 to 1992 Harley Davidson Evolution Thread plug part 50 8331 into hole B in air cleaner backplate Screw crankcase breather vent elbow fitting part 50 8110 into hole A See Figure A E Sportster models 1986 to 1990 Thread plug part 50 8331 into hole A in air cleaner backplate Screw crankcase breather vent elbow fitting part 50 8110 into hole B See Picture 1 4 Install New Manifold NOTE Whenever applicable all carburetor mounting brackets and hardware supplied in kit must be installed and used to secure carbu
29. t systems will cause poor performance at a specific rom and attempts to carburate to correct this condition usually destroys carburetion over the balance of the range A combination of cam overlap reversion and back pressure or even lack of back pressure can cause mixture dilution at certain engine rpms This dilution will cause engine roughness or misfiring when engine is held in this range Drag pipes For knucklehead panhead shovelhead and ironhead Sportster model engines 1 7 8 O D drag pipes with straight cutoff end 28 to 30 long will work well with almost any camshaft and or other performance modification 2 O D drag pipes are not recommended for any applications except very large competition engines The use of drag pipes is not recommended for Harley Davidson Evolution motors in street applications Mufflered systems A very good economical street exhaust system for Evolution and earlier engines as well consists of the stock head pipes with the cross over tube and a set of S amp S low restriction mufflers This system will typically produce 10 hp more than drag pipes in the midrange This makes an ideal system for the street since the midrange is where the vast majority of normal driving occurs NOTES General Information Carburetor body has seven drilled passages that are permanently sealed with drive plugs Do not attempt to remove these plugs as irreversible damage to carburetor may result
30. t to perform installation without removing gas tanks This option has been left to discretion of individual If one elects to remove tanks or must disassemble any other stock parts S amp S recommends owners consult appropriate service manual for their model motorcycle for reference 1 Remove Old Carburetor A WARNING Gasoline is extremely flammable and explosive under certain conditions and toxic when breathed Do not smoke Perform installation in a well ventilated area away from open flames or sparks If motorcycle has been running wait until engine and exhaust pipes have cooled down to avoid getting burned before performing any installation steps A Disconnect battery and shut off fuel petcock A WARNING Unwarranted sparks and inadvertent engagement of starter from working on electrical components can cause personal injury B Remove existing air cleaner assembly carburetor manifold choke cable and any carburetor mounting hardware 2 Check Idle Speed and Mixture Settings A Check idle mixture screw setting Turn screw See Picture 1 clockwise closing it counting number of turns to fully closed position setting should be 1 12 turns Closing adjusting screw with excessive force may cause irreversible damage to screw threads in carburetor body A CAUTION Closing idle mixture screw too tightly may cause irreversible damage to needle and seating area in carburetor body B Check engine idle speed adjusting
31. tion when you are fresh Be sure all federal state and local laws are obeyed with the installation For optimum performance and safety and to minimize potential damage to carb or other components use all mounting hardware that is provided and follow all installation instructions Motorcycle exhaust fumes are toxic and poisonous and must not be inhaled Run motorcycle in a well ventilated area where fumes can dissipate IMPORTANT NOTICE Statements in this instruction sheet preceded by the following words are of special significance A WARNING Means there is the possibility of injury to yourself or others A CAUTION Means there is the possibility of damage to the part or motorcycle NOTE Other information of particular importance has been placed in italic type S amp S recommends you take special notice of these items WARRANTY All S amp S parts are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of twelve 12 months from the date of purchase Merchandise that fails to conform to these conditions will be repaired or replaced at S amp S s option if the parts are returned to us by the purchaser within the 12 month warranty period or within 10 days thereafter In the event warranty service is required the original purchaser must call or write S amp S immediately with the problem Some problems can be rectified by a telephone call and need no further
32. ttle assembly Any chassis including 1980 and earlier stock models equipped with a single cable throttle mechanism requires conversion to a two cable pull open pull closed type A WARNING Single braided wire cable throttle mechanism can not mechanically close throttle If throttle inadvertently sticks in open position loss of control of motorcycle and personal injury to you or others may result S amp S offers an optional two cable throttle assembly designed to convert most any chassis not equipped with a two cable system This kit is available with 48 long cables and can be ordered separately See the description below Stock models from 1981 to present have a two cable throttle and should not require conversion The stock cables on these chassis can be used but must be modified Optional S amp S Two Cable Throttle Conversion Kit for chassis not equipped with two cable throttle Part 19 0229 Includes complete throttle assembly with grips for both bars and two 48 cable housing length cable assemblies Fits 1 O D handlebars and can be used on most chassis requiring up to 48 long cables Special bushings are available for use with older 78 O D handle bars Part 19 0235 Carb Installation Read instructions thoroughly before starting work to familiarize yourself with installation procedure NOTE Installation of S amp S Super B carb kits on some models is easier with gas tanks removed Some owners may elec
33. use in Harley Davidson and other American v twin motorcycles S amp S shall have no warranty or liability obligation if an S amp S part is used in any other application Important Note Please read these instructions carefully before attempting to install or tune your carburetor Answers to nearly all your questions and problems can be found in this way If you still have a problem you may call for technical help at 608 627 TECH 8324 Introduction S amp S Super B carburetor is a butterfly type carb with a fully adjustable idle mixture screw and changeable mid range and high speed jets This carburetor does not have an accelerator pump nor a conventional choke but utilizes a mixture enrichment device for starting The Super B has a 178 47 6mm throat at the butterfly and a 19 16 39 6mm venturi and is identified by an B cast into the throttle return spring side of the carb body below the cast in wording S amp S SUPER DISCLAIMER S amp S parts are designed for high performance off road racing applications and are intended for the very experienced rider only The installation of S amp S parts may void or adversely effect your factory warranty In addition such installation and use may violate certain federal state and local laws rules and ordinances as well as other laws when used on motor vehicles used on public highways especially in states where pollution laws may apply Always check federal state and l
Download Pdf Manuals
Related Search