Electric Slideout-Web.pmd
Contents
1. 6E 5 9191 02 ay ye siy ajqissod se se dul a meg2. 5 EE Z 27 11 ACTUATOR ADJUSTMENT FOR DIFFERENT ROOM SETTINGS ACTUATOR MAY BE LOCATED ON EITHER SIDE OF SYSTEM LIPPERT ELECTRIC SLIDEOUT SYSTEM LIPPERT COMPONENTS SYNCHRONIZING ROOM TRAVEL 14 The Lippert Electric Slideout System room travel both sides of the room traveling the same distance can be adjusted with specially designed synchronizing bracket mounted on the passive slide tube The passive slide tube is the one that is not powered The active slide tube is the one that has the cylinder attached If one side of the room fails to seal adjust as follows 1 Loosen bolts Fig 9 on top of the passive slide tube Fig 9B 2 Push or pull room on the passive side to align with the active side REMOVING AND REPLACING ACTUATOR MANUAL CRANK SHAFT ATTACHED WITH COTTER PIN MOTOR WIRES Fig A MOUNTING PLATE Fig B MOUNTING BOLTS STOP CAN To replace actuator Disconnect manual crank shaft from end of motor assembly Fig A Disconnect motor wires from source Fig A Take measurements A and B Fig B Remove all jam nuts 3 total and stop can from threaded shaft on actuator Fig B Take note of mounting bolt locations and remove mounting bolts Fig C After everything is disconnected slide actuator out of frame To replace with new actuator follow previous directions in reverse 15 16 TROUBLE
3. Slideout System is intended for the sole purpose of extending and retracting the slideout room Its function should not be used for any other purpose or reason than to actuate the slideout room To use the system for any reason other than what it is designed for may result in damage to the coach and or cause serious injury or even death Before actuating the system please keep these things in mind 1 Parking locations should be clear of obstructions that may cause damage when the slideout room is actuated 2 Be sure all persons are clear of the coach prior to the slideout room actuation 3 Keep hands and other body parts away from slideout mechanisms during actuation Severe injury or death may result 4 To optimize slideout actuation park coach on solid and level ground Description The Lippert Electric Slideout System is a rack amp pinion guide system utilizing an electric ball screw actuator to move the room assembly The motor drives the ball screw in a forward and backward motion to drive the slide room in and out The actuator comes equipped with an automatic clutching system The Lippert Electric Slideout System is designed to operate as a negative ground system PRIOR OPERATION Prior to operating the Lippert Electric Slideout System follow these guidelines Coach should be parked on the most level surface available Leveling or stabilizing system should be actuated to ensure coach will not move dur
4. retract and counterclockwise to extend slide out It is important to note that you DO NOT need to attempt to disengage the motor as the actuator is manual ready Just hook up and crank Use EXTREME CAUTION when extending and or retracting room using the manual override feature It is possible to operate the slideout beyond the maximum extension and or retraction and damage the slide components slide room structure or trim components WARNING The gears can be stripped out if the room is manually retracted extended to it s fullest extent and the operator continues to rotate manual override Any damage due to misuse of the Manual Override feature will disqualify any and all claims to the Limited Warranty 6 MANUAL OPERATION THROUGH FRAME Through Frame Crank Extension w pin Fig 2 Crank Handle Fig 3 MANUAL OPERATION FRAME SERVICE MECHANICAL ROOM ADJUSTMENT Vertical amp Horizontal Room Adjustment NOTE All slideout room adjustments must be performed by certified service technicians Adjustments made by non certified persons may void any and all warranty claims Horizontal adjustment 1 Loosen 2 carriage bolts A on each bracket located at the end of each guide tube 2 Room is ready to be positioned horizontally by pushing on the outside sidewall or by using a prying devise inserted into the opening between the room and coach Note Use caution when using prying devise so seals
5. sense that the room has stopped and will shut off the motor after a few seconds RETRACTING SLIDEOUT ROOM 1 Verify the battery is fully charged and hooked up to the electrical system 2 Press and hold the IN OUT switch Fig 1C in the IN position until the room is fully retracted and stops moving 3 Release the switch which will lock the room into position OTE If the slideout switch is held after the room in fully retracted the control will sense that the room has stopped and will shut off the motor after a few seconds 4 Install the transit bars if so equipped Fig 1 MANUAL OPERATION WARNING Always disconnect battery from system prior to manually operating system Failure to disconnect battery can cause electricity to backfeed through the motor and cause serious damage to the system as well as void the warranty The Lippert Electric slide comes with a manual over ride system Locate the crank extension with pin outside of the chassis main rail as Fig 2 page 7 shows underneath the unit on the end of the motor If your crank extension is under the inside of the frame please refer to page 8 This is where the crank handle standard fifth wheel landing gear crank handle or 3 4 socket and ratchet fits on to allow the manual extension retraction of the room Fig 4 5 page 8 Simply take the crank handle through frame models or wrench ratchet or drill with a nut driver in frame models and rotate it clockwise to
6. 49 LIPPERT COMPONENTS ELECTRIC SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL TABLE OF CONTENTS aa aa aai a 3 3 3 Prior to 4 Preventative 4 a a a a 5 5 Extending Slideout 5 Retracting Slideout 5 Manual 6 9 Adjustment 9 System 12 Syncronizing 14 Replacing 15 16 Wiring 19 Ordering 20 LIMITED 21 Warranty 23 SYSTEM WARNING FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH The Lippert Electric
7. NTY THIS WARRANTY EXTENDS ONLY TO THE MERCHANT ORIGINAL PURCHASER Purchaser ACQUIRING THE PRODUCT AS DEFINED HEREIN DIRECTLY FROM A LIPPERT COMPONENTS FACILITY AND SHALL NOT BE CONSTRUED TO EXTEND TO ANY THIRD PARTY INCLUDING BUT NOT LIMITED TO THE CONSUMER OR ULTIMATE PURCHASER OF THE END PRODUCT IN PART THE PURPOSE OF THIS PROVISION IS TO REQUIRE THAT ANY AND ALL WARRANTY CLAIMS BE MADE BY THE MERCHANT ORIGINAL PURCHASER AND NOT BY A CONSUMER THIS WARRANTY SUPERCEDES ANDY AND ALL PRIOR WARRANTIES LIPPERT COMPONENTS warrants the components of it s Recreational Vehicle Slide Out System Product against defects in materials and workmanship for the following time periods beginning on the date of Retail Sale so long as the Retail Sale occurs within six 6 months of the date Purchaser acquires the Product directly from a Lippert Components facility Three 3 Years Any ball screw actuator inner and out tube assembly rack and gear assembly electric motor and cross shaft Five 5 Years Any fluid power components limited to any hydraulic cylinder and hydraulic pump If a LIPPERT COMPONENTS Product is inspected by an authorized LIPPERT COMPONENTS representative and is determined to be defective in materials or workmanship within the aforementioned time period and pursuant to the requirements set forth herein LIPPERT COMPONENTS will in its sole and absolute discretion do one of the following Repair or replace
8. SHOOTING The Lippert Electric Slideout System is only one of four interrelated slideout room system components These four components are chassis room coach and Lippert Electric Slideout System Each one needs to function correctly with the others or misalignment problems will occur Every travel trailer has its own personality and what may work to fix one trailer may not work on another even if the symptoms appear to be the same When something restricts room travel system performance will be unpredictable It is very important that slide tubes be free of contamination and allowed to travel full distance Stroke Ice mud buildup during travel is an example of some types of contamination that can occur When you begin to troubleshoot the system make sure the battery is fully charged there are no visible signs of external damage to the actuator or motor and that the motor is wired correctly and all connections are secure You can adjust the room extension with the jam nuts on the end of the actuator threaded rod see page 11 During troubleshooting remember that if you change something that change may affect something else Be sure any changes you make will not create a new problem You can obtain additional information on the Lippert Electric Slideout System by calling 866 524 7821 System Troubleshooting Chart The following troubleshooting chart outlines some common problems their causes and possible corrective act
9. check as in Step 1 Step 3 If NO Inspect all connections between battery and switch Inspect 30A Auto reset Circuit Breaker See Fig 10 for location Recheck as above in Step 1 Since there are no field serviceable parts in the motor electrical troubleshooting and service is limited to replacing only those components as previously outlined Thorough inspection of wiring and connections is the only other electrical service that can be performed WIRING DIAGRAM 11 8 11 8 Fig 10 YOLOW HOLIMS iNOILNVD AMALIWE 30 81 901 13599 OLNV YOE OO 9 YOLOW YOLOW SASHSASY AdALLva 19 20 ORDERING PARTS To assist the customer service when ordering parts please provide the following information 1 Your Name 2 Company Name 3 Phone Number 4 Shipping Address 5 Billing Address 6 Purchase Order Number 7 Coach A Serial and or VIN B Make C Model 8 Part Number 9 Description 10 Quantity Please take your coach to an authorized service center for repairs Systems that have been modified adjusted repaired or augmented by a party other than an authorized service center may void any warranty claim with Lippert Components Inc LIMITED WARRA
10. do not become damaged Vertical adjustment 1 Loosen 2 carriage bolts A on each bracket located at the end of each guide tube 2 Loosen jam nut 3 For vertical adjustment turn vertical adjustment bolt B up or down to locate room height Once room is located tighten A and Jam Nut bolts MECHANICAL ROOM ADJUSTMENT E gt Bolt A 4 _ Bolt Bolt 7 4 Adjusting room so it seals the IN position 1 Locate actuator coming through the frame 2 On the end of the actuator there is a threaded shaft mounted to the drive bracket with 3 nuts and a stop can 3 Loosen the 3 nut Jam Nut 1 on the outside of the stop can 4 Screw the can out or in and then tighten down the nut this will change the location of your seal going to the in position Adjusting room so it seals in the OUT position 1 Locate actuator coming through the frame 2 On the end of the actuator there is a threaded shaft mounted to the bracket with 3 nuts and a stop can 3 Move one of the 1 nuts Jam Nut 2 or Nylock Nut one way or the other this will change the location of your seal going to the out position 4 Make sure all nuts are tight 11 12 PART NUMBER OUTER RAIL ASSEMBLY INNER RAIL ASSEMBLY INNER DRIVE TUBE ACTUATOR MOTOR ASSEMBLY 2
11. e to chassis contact To ensure the best possible ground a star washer should be used Over 90 of unit electrical problems are due to bad ground connections Mechanical Maintenance Although the system is designed to be almost maintenance free actuate the room once or twice a month to keep the seals and internal moving parts lubricated Check for any visible signs of external damage after and before movement of the travel trailer NOTE For long term storage It is recommend that the room be closed retracted WARNING FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH ALWAYS MAKE SURE THAT THE SLIDEOUT ROOM PATH IS CLEAR OF PEOPLE AND OBJECTS BEFORE AND DURING OPERATION OF THE SLIDEOUT ROOM ALWAYS KEEP AWAY FROM THE SLIDE RAILS WHEN THE ROOM IS BEING OPERATED THE GEAR ASSEMBLY MAY PINCH OR CATCH ON LOOSE CLOTHING CAUSING PERSONAL INJURY INSTALL TRANSIT BARS IF SO EQUIPPED ON THE SLIDEOUT ROOM DURING STORAGE AND TRANSPORTATION EXTENDING SLIDEOUT ROOM 1 Level the unit Verify the battery is fully charged and hooked up to the electrical system 3 Remove the transit bars if so equipped 4 Press and hold the IN OUT switch Fig 1B in the OUT position until the room is fully extended and stops moving 5 Release the switch which will lock the room into position ote If the slideout switch is held after the room in fully extended the control will
12. formed by others must have the prior authorization of LIPPERT COMPONENTS to be honored Third Party Events In the event of any accident injury to person damage to property loss or other occurrence involving a LIPPERT COMPONENTS Product Purchaser shall notify LIPPERT COMPONENTS of such event within thirty 30 days of the event or within ten 10 days of the notification to Purchaser whichever is earlier Notwithstanding the foregoing Purchaser shall notify LIPPERT COMPONENTS immediately upon learning that a survey test or inspection is to be made with respect to the LIPPERT COMPONENTS Product and provide LIPPERT COMPONENTS with the opportunity to participate in any such survey test or inspection or to permit LIPPERT COMPONENTS to conduct its own survey test or inspection Failure to comply with each of the foregoing shall bar any claim by the Purchaser against LIPPERT COMPONENTS concerning any such event and shall require Purchaser to defend indemnify and hold LIPPERT COMPONENTS harmless from all claims asserted against LIPPERT COMPONENTS concerning any liability of LIPPERT COMPONENTS arising out of such event Severability Any legally or otherwise invalid provision hereof shall be considered severable Any conditions or exceptions which may be stated in any communication or document received by LIPPERT COMPONENTS from any entity or individual including but not limited to the Purchaser shall be of no effect unless specifically agreed
13. ing operation of Slideout System Be sure battery is fully charged Be sure to keep all persons and pets clear of Slideout System during operation RO N gt SYSTEM MAINTENANCE The Lippert Electric Slideout System has been static tested to over 4 000 continuous cycles with out any noticeable wear to rotating or sliding parts It is recommended that when operating in harsh environments road salt ice build up etc the moving parts be kept clean and can be washed with mild soap and water No grease or lubrication is necessary and in some situations may be detrimental to the environment and long term dependability of the system Electrical System Maintenance For optimum performance the slide out system requires full battery current and voltage The battery must be maintained at full capacity Other than good battery maintenance check the terminals and other connections at the battery the control switch and the electric actuator motor for corrosion and loose or damaged terminals Check motor leads under the trailer chassis Since these connections are subject to damage from road debris be sure they are in good condition Note The Lippert Electric Slideout System is designed to operate as a negative ground system A negative ground system utilizes the chassis frame as a ground and an independent ground wire back to battery is necessary see page 19 for wiring diagram It is important that the electrical components have good wir
14. ions When reference is made to Power Unit it is referring to the motor and actuator as a complete assembly All Power Units are shipped from the factory with a serial number and date code which should be given to the service technician when asking for assistance ROOM DOESN T MOVE WHEN SWITCH IS PRESSED Probable cause Corrective action Restrictions both inside and out side unit Check for and clear restriction Low battery voltage blown fuse defective wiring Check battery Charge battery or add auxiliary power source Check battery terminals and all other wiring Look for loose corroded connectors Power unit not functioning See Troubleshooting on page 5 POWER UNIT RUNS BUT ROOM DOES NOT MOVE Actuator not attached to front mounting Check jam nuts nylock nuts Be sure that drive bracket they are properly tightened and adjusted Bad motor or gear housing Replace motor POWERUNIT RUNS BUT ROOM MOVES SLOWLY Low battery poor ground extremely Charge battery and check ground wire low outdoor temperature Room is in a bind Check to see that room is properly adjusted ROOM STALLS IN MID TRAVEL Actuator in a bind Crank manual override and move room short distance then retry electric switch to move room Bad actuator Replace actuator if above instructions do not work If the slideout room will not retract there is a manual override that is located on the opposite side of the slideout room A crank handle
15. is provided with your unit Once you have the room in the closed position take you unit to the closest dealer See pages 8 amp 9 NOTES Switch related problems If room moves opposite from what the switch plate indicates reverse the motor wires back of switch refer to the wiring diagram Wire size must be 10 GA Minimum If you find that you have stripped gear replace the gear pack If the room is out of time synchronization refer to pages 10 amp 13 17 18 TROUBLESHOOTING MOTOR Before attempting to troubleshoot the Motor make sure an adequate power source is available The unit batteries should be fully charged or the unit should be plugged into to A C service with batteries installed Do not attempt to troubleshoot the Motor without assuring a full 12V DC charge The following tests require only a DC voltmeter or DC test light and a jumper lead Step 1 Attach voltmeter or test light leads to the negative and positive switch terminals on back of wall switch See Fig 10 Does the meter indicate 12V DC If YES see Step 2 if NO see Step 3 Step 2 If YES at the motor check the incoming leads to 12V DC if necessary disconnect leads at wire splices Does meter indicate 12V DC If YES Motor needs to be replaced The motor is not field serviceable DO NOT ATTEMPT TO REPAIR If NO Inspect all wires and connections between the wall switch and the motor Repair connections as necessary Re
16. or incorrect weight bias loading damage resulting from improper operation or maintenance connection to improper towing unit or attempted repair by anyone other than an authorized representative of LIPPERT COMPONENTS This warranty does not cover cosmetic damage damage due to acts of God commercial use or modification of the Product or Products sold AS IS and or WITH ALL FAULTS This warranty is valid only in the United States and Canada EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED REPAIR REPLACEMENT OR CREDIT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER IN NO EVENT WILL LIPPERT COMPONENTS LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Claims claims are barred unless reported in writing by Purchaser to LIPPERT COMPONENTS with full particulars promptly after the damage was or reasonably should have been discovered and full facilities are offered LIPPERT COMPONENTS for inspection and investigation LIPPERT COMPONENTS will not consider any claims for material that is not in the original form 21 All written notices required by this warranty shall be sent to Lippert Components Inc Attn Risk Management Department 2375 Tamiani Trail N Suite 1101 Naples FL 34103 This warranty is invalid if factory applied identification criteria have been altered or removed from the Product Work per
17. to in writing by LIPPERT COMPONENTS The current warranties and terms outlined on LIPPERT COMPONENTS website www lippertcomponents com on the date of the purchase shall take precedence over any other warranties whether verbal or written LIPPERT COMPONENTS reserves the right to alter its warranties from time to time as the laws and the company s business needs and industry change TO THE GREATEST EXTENT PERMITTED BY LAW ANY CONTROVERSY OR CLAIM ARISING OUT OF OR IN RELATIONS TO THIS WARRANTY SHALL BE DETERMINED BY BINDING ARBITRATION IN NAPLES FLORIDA COLLIER COUNTY INACCORDANCE WITH THE COMMERCIAL ARBITRATION RULES OF THE AMERICAN ARBITRATION ASSOCIATION PURCHASE OF THE PRODUCT CONSTITUTES PURCHASER S AGREEMENT TO THIS PROVISION 5 diz 91816 107 10 Idy 194 0 5 5 5 21149913 Ajdde yeu 71 49949 9124 9124 synoaplis jo NIA 91 AY uy Aenemo oy SN 1282 725 998 42 110 SN 82697 NI Uaysoy 2022
18. without charge FOB it s factory Send a service team to the then current location of the Product to repair or replace it on site or allow credit for the Product All warranty claims MUST involve an inspection of the Product and be approved by an authorized LIPPERT COMPONENTS representative and all repair procedures must be pre approved by LIPPERT COMPONENTS before any repair work can begin There are no exceptions to this procedure so please contact your LIPPERT COMPONENTS division immediately before attempting any repairs or modifications on your LIPPERT COMPONENTS Product No claim for Products alleged to be defective will be allowed until LCI has had a reasonable opportunity to investigate each claim This warranty does not cover customer instruction installation or set up adjustments Unless otherwise indicated by tangible evidence LIPPERT COMPONENTS relies upon the engineering professionals of those that purchase its Products to design and specify a Product of sufficient size dimension strength and durability to support the structure the Purchaser intends to place upon the Product and to design and specify a Product that is sufficient and adequate to function in the role the Purchaser intends to use and or produced by its Purchasers and builds Products pursuant to those design specifications This warranty does not cover abuse misuse or neglect but is not limited to improper usage overloading accident related damage improper loading
Download Pdf Manuals
Related Search