2012 - Bernardi Parts
Contents
1. e Tightening the nut above the specified torque can damage the grommet Make sure that there is no gap between the sensor and the wheel 4 Install the tires according to the procedure in the service manual Be careful not to damage the new sensor 2011 American Honda Motor Co Inc All Rights Reserved 5 Using isopropyl alcohol on a shop towel clean the area where the center cap emblem will attach 6 Removethe adhesive backing from the center cap emblem WHEEL CENTER CAP PUSH NUTS ADHESIVE BACKING Note the direction of the push nuts E CENTER CAP EMBLEM CENTER CAP WHEEL EMBLEM CENTER CAP 7 Attach the center cap emblem to the wheel center cap by aligning its pins with the holes in the wheel center cap After attaching hold the emblem firmly against the wheel center cap with the palm 10 11 of your hand for 30 seconds 8 Slide the push nuts onto the pins Note the direction of the push nuts 9 Install the cap onto the wheel 12 2011 American Honda Motor Co Inc All Rights Reserved BIl 46117 1108 Open the driver s door Using isopropyl alcohol clean the tire pressure information label on the doorjamb Remove the adhesive backing from the new information label and attach it over the old label 10 DIGIT NUMBER 1 TIRE PRESSURE INFORMATION LABEL 0 CURRENT TIRE INFORMATION NEW TIRE LABEL PRESSURE INFORMATION LABEL E LZ ai Insta2. A ACURA INSTALLATION INSTRUCTIONS PARTS LIST Aluminum wheel The illustration may differ from the actual wheel Wheel center cap The illustration may differ from the actual center cap Center cap emblem 2 Push nuts Tire pressure information label Important information Wheel cleaning information Give this information to your client TPMS information Give this information to your client 2011 American Honda Motor Co Inc All Rights Reserved 19 ALUMINUM WHEEL Application Publications No BII 46117 2012 RDX Issue Date AUG 2011 Parts for TPMS sensor assembly 7 gt Tire pressure sensor assembly Washer Valve cap Valve nut TOOLS AND SUPPLIES REQUIRED Ratchet 11 mm Socket Torque wrench Isopropyl alcohol Shop towel SPECIFICATIONS Rim size 19 x 8 J offset 45 Tire size 245 45R19 98Y Bolt hole PCD 114 3 5 holes 33 psi Front 550 kPa 2 3 kgf cm Tire pressure Rear pi 230 kPa 2 3 kgf cm BII 46117 1108 08W19 sTK 2000 931 1 of 6 INSTALLATION Client Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers NOTE 1 2 of 6 This aluminum wheel is d
3. esigned for use on vehicles equipped with TPMS Tire Pressure Monitoring System This aluminum wheel is equipped with a TPMS sensor See the service manual for the tire replacement procedure and TPMS sensor installation procedure Install the correct size tire 245 45R19 98Y The wheel nut torque is 108 N m 80 Ib ft Be careful not to damage the wheel center cap when installing the emblem The center cap emblem kit should be installed only if the ambient air temperature is 60 F 15 C or above To allow the adhesive to cure do not wash the vehicle for 24 hours Before installing the tire pressure sensor clean the mating surface on the sensor and the aluminum wheel BII 46117 1108 2 Install the tire pressure sensor to the aluminum wheel and loosely install the valve nut Make sure the pressure sensor is resting on the wheel WASHER Se GROMMET WW Do not allow the tire pressure sensor to rotate as you torque the valve nut Nl gt OUTSIDE WASHER d TIRE PRESSURE SENSOR WHEEL VALVE NUT CENTER Torque 4 N m 36 in Ib ALUMINUM WHEEL 3 Torque the valve nut to 4 N m 36 in Ib while holding the tire pressure sensor toward the wheel You may hear a snap or pop as you tighten the nut this is normal NOTE Donotreuse a grommet that has already been torqued If you do the valve stem may leak e Do not use pneumatic or electric tools on the valve nut
4. ion code printed on the new tire pressure information label then click the check icon 22 Checkthat the tire pressure shown on the HDS matches the one on the new tire pressure information label then click the YES button 23 Check that the current air pressure setting shown on the HDS is correct and Reprogramming the threshold data for non standard tires has completed successfully is shown 24 Write the tire pressure indicated on the HDS in the service history page for Acura Accessory Wheels then click the check icon T TIRE PRESSURE INFORMATION LABEL DATA LINK CONNECTOR Yod TVnNVM S H3N O 33S AIR VI z zo o 5 Es Az S g 10 DIGIT CODE NOLLVINHOHNI 5NIQVO 1 QNV 3YIL I g o 4 of 6 BII 46117 1107 2011 American Honda Motor Co Inc All Rights Reserved 25 Sign on the service history page for Acura Accessory Wheels according to the procedure on page 5 26 Write the tire size tire pressure HDS version dealer name technician s signature and date in the service history page for Acura Accessory Wheels page and attach the page to the vehicle s service history booklet NOTE Explain the changes made in the service history booklet to your client before delivering the vehicle Be sure to give the wheel cleaning information and TPMS information to your client STANDARD TIRE PRESSURE PROGRAMMING If the original equipment standard wheels are reinstalled on the
5. ll the wheels on the vehicle and torque them to 108 N m 80 lb ft Put the valve stems at the 12 o clock position before lowering the vehicle to the ground Do the sensor ID learning procedure see page 4 3 of 6 SENSOR ID LEARNING NOTE To ensure that the control unit memorizes the correct IDs park the vehicle with the new sensors at least 3 m 10 ft from any other TPMS pressure sensor not installed on that vehicle 13 Connect the HDS to the vehicle make sure the correct VIN is populated and enter the mileage 14 At the System Selection Menu click TPMS 15 Atthe Mode Menu click DTC and clear any stored codes 16 Go back to the Mode Menu click Sensor ID Learning and follow the screen prompts NOTE If the sensor ID learning fails have an assistant drive the vehicle under 10 mph while you redo the ID learning procedure The TPMS control unit should learn all four sensor IDs If one or more of the sensor IDs are not learned then go to normal troubleshooting in the service manual before continuing If all four sensor IDs are learned go to step 17 LOW TIRE PRESSURE WARNING THRESHOLD REPROGRAMMING 17 From the TPMS Mode Menu click on Threshold Rewriting 18 Select Reprogramming for accessory tires 19 When the HDS says Do you want to rewrite the threshold data click YES 20 When Please enter the tire information code of new tires is shown click the Keyboard icon 21 Enter the 10 digit tire informat
6. the TPMS control unit is installed redo sensor ID learning and low tire pressure warning threshold reprogramming see page 4 6 of 6 BII 46117 1108 2011 American Honda Motor Co Inc All Rights Reserved
7. vehicle the low pressure warning threshold must be restored to the factory setting To return the TPMS programming from the inch up wheel to the standard wheel do the following 1 Connectthe HDS to the vehicle make sure the correct VIN is populated and enter the mileage 2 Atthe System Selection Menu click TPMS 3 Atthe Mode Menu click DTC and clear any stored codes 4 Go back to the Mode Menu click Threshold Rewriting 5 Click on Reprogramming for standard tires and follow the screen prompts 6 After programming write the measured tire pressure in the important information then click the check button 7 Attach the standard tire pressure information label over the old label in the driver s doorjamb After programming sign the service history page for Acura Accessory Wheels DATA LINK CONNECTOR HDS 2011 American Honda Motor Co Inc All Rights Reserved BII 46117 1107 5 of 6 THRESHOLD DATA CHECK If you are unsure of where the low pressure warning threshold is set it can be checked by using Threshold Data Check 1 Connectthe HDS to the vehicle make sure the correct VIN is populated and enter the mileage 2 Atthe System Selection Menu click TPMS 3 Click on Threshold Rewriting 4 Clickon Threshold Data Check DATA LINK CONNECTOR HDS TPMS UNIT REPLACEMENT If the TPMS control unit is replaced and the vehicle has inch up wheels the low pressure sensor threshold must be changed Once
Download Pdf Manuals
Related Search