Instructions: - Autohifidiszkont
Contents
1. above steps for other headlamp 10 Working with one headlight at a time twist the 2 12V leads together and crimp the included terminal onto the wire leads making note of the correct terminal for the opposite leads on the wiring harness Repeat on other headlamp 11 Tuck your connections and excess wiring away from extreme heat or other moisture elements 12 Connect the power wires and test the Angel Eyes before routing the cables Connect the larger gauge red to the 12V positive and the black to chassis ground The small red white wires going to a 12V source temporarily for testing Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m6 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued nm Ro v4 4 wwe b Ge g ef TO S 13 Mount the Angel Eye harness relay to the inner side of the empty compartment underneath the hood as indicated in the diagrams The plastic shroud on the 12V terminal can be removed temporarily to attach the positive power lead with the black terminal ring going to chassis ground ac a 14 Begin to route the wiring for the dri2. 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 July 2008 INSTALLATION SUPPLEMENT FOR BMW v1 0 Subject e2 aurora angel Eyes for BMW Models Supported 1999 2003 e46 3 series pre facelift non sealed lamps 2000 2006 e46 M3 Coupe Convertible 1995 2001 e38 7 series 1997 2000 e39 5 series Recommended Installation Time 45 60 minutes Congratulations on purchasing aurora the best in angel eyes for your BMW Note Professional installation is highly recommended if you do not have prior experience with your BMW s electrical system Please consult a factory service manual for the exact location and disassembly instructions if you are unsure of the procedures Turn the ignition key to the off position It is a good idea to disconnect both battery cables and set aside to prevent any electrical shorts Items needed aurora 6OLED Angel Eye kit Phillips screwdriver Crimping Pliers Allen Torx Wrench assortment depending on model year Instructions In this DIY we are going to install the aurora angel eye kit into a 2006 BMW M3 ZCP equipped with Bi Xenon headlamps First the aurora angel eye kit comes in 4 major pieces 4 highly polished Angel Eye rings with integrated LED circuitboards 2 Multi stage Mounting Clips amp Solderless connectors T Taps 1 Heavy Duty Wiring harness comes with
3. different angles of the rings installed Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m4 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued 7 The wiring can exit the rear rubber boot behind the headlamp Poke a tiny hole in the rubber so the wiring when passed through is not chafed on any metal or plastic parts 8 Here are completed images of the rings on the reflector housings Aurora has a multi stage clipping mechanism in order to align the clips perfectly onto your housings with interference from auto leveling mechanisms Take care in verifying the rings are perfectly aligned by inspecting at different angles Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited ead without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued 9 Repeat
4. emove the trim underneath the steering wheel to gain access to the LCM wiring Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m9 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Powering options Switched continued TO Ee 21 Remove the trim underneath the steering wheel to gain access to the LCM wiring This is located in a thick bundle going towards the steering column 22 Tap into the grey wire with purple stripe on the wiring bundle this will allow the Angel Eyes to turn on with the parking lights Replace interior panels and test to verify connections are secure Final installation amp testing To use the remote feature simply open the door and the Angel Eyes will fade on Lock the BMW with the key and the Angel Eyes will fade off reappearing on when the doors are unlocked with the interior lights Turning on the ignition will turn on the Angel Eyes with the Always on option If you have wiring into the switched mode you can turn on off the Angel Eyes with the parking light switch Copyright 2008 eas inc Reproduction distribution modification transmission or pub
5. footwell lighting and tap into the red wire of the connector with a scotchlock or solder into place Reconnect the connector to the footwell lamp and reinstall the glovebox back into place Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m8 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Powering options Always on vs Switched You have 2 options of powering on your new Angel Eyes One option easiest would be to tap into the power wire of the DME which would result into the Angel Eyes being placed into an always on state meaning that the Angel Eyes will be on whenever the vehicle is running even in daytime Another option would be to wire to the LCM parking light wire in the cabin area While this is a bit more effort to accomplish you have the added option of turning on off the Angel Eyes when desired Always on 19 Remove the DME cover using a torx or allen bit depending on model year to expose the wiring The red white wire of the harness will be tapping into the red wire w white stripe with yellow dots Make sure the wire has the yellow dots before tapping Switched a7 20 R
6. ing the inner tab closest to the kidney grilles Then release the outer clip of the lower trim by pressing on the outer tab using a pick tool Once trim is detached the headlight can be removed Be careful to make sure the lower headlamp trim painted portion is not damaged when removing the lamp 4 Remove the headlight lens This is held in by lifting the retaining clips on the upper and lower portions of the lens Set the lens aside and cover it to prevent dust from collecting on the inside Insert the clipping mechanisms onto the aurora rings in an upward motion stepping them into the mounting slots on the ring bridge Take care when inserting the clips as the rings are fragile and can break under pressure Repeat the steps for the remaining rings Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m3 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued 5 Clip the Angel Eye rings onto the reflector housing If equipped with auto level feature make sure there is enough clearance for the projector to move up down without coming in contact of the ring at 6 These images show
7. lication of any copyrighted material is strictly prohibited 10 without the express written consent of eas Violation will result in prosecution to the full extent available under law
8. relay and remote feature Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited eal without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place UnitB Santa Ana CA 92705 tel 714 369 8524 email web fax 714 908 1796 Instructions continued This will cover two possibilities having the halo rings on all the time when the vehicle is running or the option of wiring to the LCM preferred so you can turn on off the Angel Eyes when desired 1 Inthis DIY we are going to install the aurora Angel Eye kit into a 2006 BMW M3 ZCP equipped with Bi Xenon headlamps Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited m2 without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued 3 Remove the corner lens This will either be a screw type Phillips or push in design The screw type will simply unscrew off the push in have a retaining clip that is pushed down to remove the lens Remove lower headlight trim by unclipp
9. ver s side Angel Eye rings and trigger lead by unclipping the wiring shroud so the harness can tuck inside for a clean OEM look when finished Pay careful attention to not allow wiring to chafe on the empty engine compartment metal it should be insulated by the existing rubber insulator 15 Route wiring to the driver s side headlights and connect to the wiring leads on the power leads going to the aurora rings Copyright 2008 eas inc Reproduction distribution modification transmission or publication of any copyrighted material is strictly prohibited esa without the express written consent of eas Violation will result in prosecution to the full extent available under law 1305 E St Gertrude Place Unit B Santa Ana CA 92705 tel 714 369 8524 email info europeanautosource com web www europeanautosource com fax 714 908 1796 Instructions continued 16 In order to enable the remote feature the red white wire closest to the relay will need to be connected to the interior lighting this allows the fade in out feature of the Angel Eyes when the doors are locked unlocked Start by removing the 7 phillips screws and 2 retaining clips holding on the glovebox and dropping it out of place 17 Remove the oval grommet and poke a small hole for the trigger wire to pass through the interior opening Route the wire through the opening and replace the grommet back into place 18 Unplug the connector going into the
Download Pdf Manuals
Related Search