HP LaserJet P3010 Service Manual
Contents
1. 9 4 NI CAUTION To avoid damaging the fuser the cartridge door assembly must be closed before you remove the fuser Figure 2 84 Removing the fuser 4 of 4 _ A Pg rh fr a i of OF de K f m ys AA i F bz t ra we ae ee a7 a ENWW Removal and replacement procedures 1012. Chapter2 Removal and replacement ENWW For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 3 If necessary remove the gear the bushing and the spring and then install them on a replacement roller Figure 2 72 Remove the transfer roller 3 of 3 ENWW Removal and replacement procedures 93 For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Fuser 1 Before proceeding remove the following components e Rear door assembly See Rear door assembly on page 62 e Right rear cover See Ric inierear cover on page 68 2 Duplex models only Release two tabs callout 1 on the duplex media feed guide and then slide the guide toward the back of the product to remove it X Reinstallation tip Make sure that both tabs snap back into place when reinstalling the duplex media feed guide XS Figure 2 81 Remove the fuser 1 of 4 4 A AY V KN A Y h A gt q 3 Disconnect three connectors callout 1 and release one wire harness from the retainer callout 2 Figure 2 82 Remove the fuser 2 of 4 a 100 Chapter 2 Removal and replacement ENWW For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 4 Remove four screws callout 1 Figure 2 83 Removing the fuser 3 of 4 PY n 5 Pull the fuser out of the back of the product
3. For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Main assemblies Tray 1 multipurpose tray pickup roller A CAUTION Do not touch the surface of the roller Skin oils deposited on the roller might cause print quality problems 1 Press the cartridge door release button and then open the cartridge door Make sure that the door is completely open gt Figure 2 60 Remove the Tray 1 MP tray pickup roller 1 of 2 2 Release two tabs and then rotate the roller out and away from the product to remove it X TIP It might be easier to release the tabs by using a small flat blade screwdriver Figure 2 61 Remove the Tray 1 MP tray pickup roller 2 of 2 86 Chapter 2 Removal and replacement ENWW For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Tray 1 multipurpose tray separation pad A CAUTION Do not touch the surface of the pad Skin oils deposited on the roller might cause paper handling problems 1 Press the cartridge door release button and then open the cartridge door Make sure that the door is completely open Figure 2 62 Remove the ray 1 multipurpose tray separation pad 1 of 2 2 Release two tabs callout 1 and then remove the separation pad Figure 2 63 Remove the Tray 1 multipurpose tray separation pad 2 of 2 ENWW Removal and replacement procedures 87
4. For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Tray 2 Tray 3 or Tray 4 pickup roller A CAUTION Do not touch the surface of the roller Skin oils deposited on the roller might cause print quality problems EY NOTE Ifyou did not remove the Tray 2 Tray 3 or Tray 4 cassette before servicing the product remove it now io A 1 Carefully place the produc tro At side up so that you can see into the opening where the cassette would be installed _ rey E NOTE Debris can scratch or damage the back of the product Before you place the product front side up remove any debris from the work surface If possible set the product on a clean dry cloth to prevent scratching and damage 2 Release the roller pushing rotate the busing up and then slide the bushing off of the roller shaft Figure 2 64 Remove the Tray 2 ay 3 or Tray 4 pickup roller 1 of 3 88 Chapter2 Removal and replacement ENWW For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 3 Carefully remove the black plastic guard callout 1 A CAUTION The guard is partially retained by the bushing removed in the previous step Do not lose the guard when the bushing is removed Figure 2 65 Remove the Tray 2 Tray 3 or Tray 4 pickup roller 2 of 3 d da i 4 Slide the roller toward the left side of the product rotate the right en
5. d of the roller away from the product and then remove the roller assembly Figure 2 66 Remove the Tray 2 Tray 3 or Tray 4 pickup roller 3 of 3 Sate A to es ENWW Removal and replacement procedures 89 For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Tray 2 Tray 3 or Tray 4 separation pad A CAUTION Do not touch the surface of the pad Skin oils deposited on the roller might cause paper handling problems 1 Remove the tray cassette See Iray cassette Tray 2 Tray 3 or Tray 4 on page 54 2 Remove two screws call d then remove the separation pad callout 2 how Figure 2 67 Remo ve th ray Tray 3 or Tray 4 separation pad 90 Chapter 2 Removal and replacement ENWW For more information on the HP LaserJet P3010 P3015 visit us at www PrinterSupplies com or call 800 551 1943 Transfer roller A CAUTION Do not touch the black sponge portion of the transfer roller Skin oils deposited on the transfer roller might cause print quality problems 1 Press the cartridge door release button and then open the cartridge door Make sure that the door is completely open a 2 Release two tabs callout 1 at the left end of the roller slightly lift the end of the roller up and then slide the roller callout 2 toward the left to release it Remove the roller Figure 2 71 Remove the transfer roller 2 of 3 r n aia a 92
Download Pdf Manuals
Related Search