HistoCore Arcadia C
Contents
1. 4 4 Moving the instrument Do not move the instrument during operation Before moving the instrument make sure that there is no specimen blocks on the cold plate the instrument is at an ambient temperature and the power cord is disconnected from the power supply Do not touch the metal parts of the compressor air outlet 1 on the rear panel It is mandatory to observe a waiting time of 4 hours before the instrument is switched Hold the instrument at the front and rear part of the lower housing base and move Fig 7 HistoCore Arcadia C Cold Plate 15 4 Setting up the instrument 45 Power supply The HistoCore Arcadia C refrigeration unit requires a specific voltage and frequency refer to Technical data chapter and is therefore always delivered with a power cord that fits the instrument Please observe the following notes to prevent damage to the instrument A Before connecting the instrument to the power supply it is mandatory to check whether power receptacle Do not use an extension cord the voltage specified on the identification label rear side matches the actual voltage values at the installation location If this is not the case the connection must not be made The unit must be connected only with the supplied power cord and only to a grounded An I IN a Depending on the application area one of the following cables is delivered along2. contact customer service The cold plate cannot cool down to the target temperature but no alarm Ambient temperature Is too high Or Too much condensated water ice frost on the cold plate surface 1 Make sure that the room temperature is 20 30 C 2 Make sure that enough Space Is reserved between the wall and the instrument It must be at least 15 cm 3 Clean the cold plate and restart the instrument 4 If the problem persists contact customer service The temperature of the cold plate is too low and the alarm beeps steady may cause cracks on the paraffin blocks The cold plate is malfunctioned 1 Restart the instrument 2 If the problem persists contact customer service HistoCore Arcadia C Cold Plate 19 8 Warranty and Service Warranty Service information Leica Biosystems Nussloch GmbH guarantees that the contractual product delivered has been subjected to a comprehensive quality control procedure based on the Leica Biosystems in house testing standards and that the product is faultless and complies with all technical specifications and or characteristics warranted The scope of the warranty is based on the content of the concluded agree ment The warranty terms of your Leica Biosystems sales organization or the organization from which you have purchased the contractual product shall apply exclusively If you require technical service or replacement parts
3. please contact your Leica Biosystems sales representative or dealer who sold the product Please provide the following information e Model name and serial number of the instrument e Location of the instrument and name of the person to contact e Reason for the service call e Date of delivery Decommissioning and disposal 20 The instrument or parts of the instrument must be disposed of in compliance with the local laws Instructions for Use V 1 2 Rev C 06 2015 9 Decontamination Certificate Master Dear Customer Any product that is to be returned to Leica Biosystems or serviced on site must be cleaned and decontaminated in the appropriate manner Since it is not possible to decontaminate for prion diseases such as CUD BSE CWD etc equipment exposed to specimens containing prion diseases cannot be returned to Leica Biosystems for repair On site repair of prion contaminated equipment will only be conducted after the Field Service Engineer has been educated in the risks instructed in the policies and procedures of the institution and provided with personal protective equipment Please fill out this confirmation carefully and enclose a copy with the instrument Attach the confirmation to the outside of the flight case or hand it directly to the service technician Packages will not be opened nor servicing commenced until the Company or service engineer have received a satisfactory certificate Should returned goods
4. are marked by an information symbol i gt Numbers in parentheses refer to item numbers in illustrations or to the illustrations igure 5 themselves EE T1 Ol Caution consult the instructions for use for cautionary information Power on ce Power off Observe the Instructions for Use Manufacturer Date of manufacture Symbol for alternating current PE terminal Order No s ULE RO HistoCore Arcadia C Cold Plate 3 1 Important Information 1 2 Symbols in the text and their meanings Serial number Environmental protection symbol of the China RoHS directive The number in the symbol indicates the Environment friendly Use Period of the product The symbol is used if a substance restricted in China is used in excess of the max imum permitted limit Symbol for labeling electrical and electronic equipment in accordance with Sec tion 7 of the German Electrical and Electronic Equipment Act ElektroG ElektroG is the law regarding the sale return and environmentally sound disposal of electrical and electronic equipment This product fulfills the requirements of the EU directives This product fulfills the requirements of the CAN CSA C22 2 No 61010 The package contents are fragile and must be handled with care The package must be kept in a dry environment Indicates the correct upright position of the package It allows maximum 2 stacks layers 4 Instructio
5. with the in Fig 8 e Connect the power cord plug 7 to the connecting port 6 e Plug the power cord into the wall outlet 16 strument Designation Order No USA 14 6000 05024 Japan 14 6000 05025 Brazil 14 6000 05026 Europe 14 6000 05027 China 14 6000 05028 Australia 14 6000 05029 United Kingdom 14 6000 05030 Switzerland 14 6000 05066 Italy 14 6000 05067 Denmark 14 6000 05068 Argentina 14 6000 05070 Instructions for Use V 1 2 Rev C 06 2015 5 Operation 5 1 Switching the instrument on After installation as described in Chapter 4 the HistoCore Arcadia C is ready for operation Switch on the device with the Power switch at the front left of the instrument I ON A lamp lights up in the switch to indicate that the unit is op erational and the refrigeration unit will start working Depending on the room temperature the time to reach the target temperature of the cooling surface 6 C will be around 25 minutes The cooling surface may not be loaded with molds until the cooling time has elapsed Otherwise the working temperature of 6 C may not be reached 1 The compressor will start to work in five minutes after the power is on 5 2 Replacing the secondary fuse Fig 10 HistoCore Arcadia C Cold Plate A miniature fuse to protect the electronic components Is located on the rear of the instrument Fu
6. 2 24 143 0 Fax 49 0 6224 143 268 Internet http www LeicaBlosystems com These are determined only by the contract provisions agreed between ourselves and our Customers Leica Biosystems reserves the right to change technical specifications as well as manufactur ing processes without prior notice Only in this way Is It possible to continuously improve the technology and manufacturing techniques used in our products This document is protected under copyright laws All copyrights to this documentation are held by Leica Biosystems Nussloch GmbH Any reproduction of text and illustrations or of any parts thereof by means of print photo copy microfiche web cam or other methods including any electronic systems and media requires express prior permission in writing by Leica Biosystems Nussloch GmbH For the instrument serial number and year of manufacture please refer to the name plate at the back of the instrument Leica Biosystems Nussloch GmbH Assembly contracted to Leica Microsystems Ltd Shanghai HistoCore Arcadia C Cold Plate Table of contents 1 Important Information cc csesseeesseeeeeseseeeeaeseeeseaeseeeeassesesaeaeseseeaeseseeaeasseeesaeeeeeaneeenens 3 Vel Naminio COMMOTION S mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmr 3 12 Symbols in The text and their ME ANN GS sicssccscsiecavscoctecevssaczctenssneessstansanciaa tansdacduaeiaetdaseatneedtnatenss 3 ko AIS CIETY G U0
7. Seica BIOSYSTEMS Instructions for Use HistoCore Arcadia C Cold Plate HistoCore Arcadia C V 1 2 English 06 2015 Order No 14 0393 80101 Rev C Always keep this manual with the instrument Read carefully before working with the instrument NOTE The information numerical data notes and value judgments contained in this manual represent the current state of scientific knowledge and state of the art technology as we understand It following thorough investigation in this field We are under no obligation to update the present manual periodically and on an ongoing basis according to the latest technical developments nor to provide our customers with additional copies updates etc of this manual To the extent permitted in accordance with the national legal system as applicable in each individual case we shall not be held liable for erroneous statements drawings technical illustrations etc contained in this manual In particular no liability whatsoever is accepted for any financial loss or consequential damage caused by or related to compliance with state ments or other information in this manual Statements drawings illustrations and other information regarding the contents or technical details of the present Instructions for Use are not to be considered warranted characteristics of our products esol Leica Biosystems Nussloch GmbH Heidelberger Str 17 19 D 69226 Nussloch Germany Phone 49 0 6
8. afety features are in prop er working condition Malfunctions that impede safety must be remedied immediately For current information about applicable guidelines please refer to the CE declaration of conformity and on our Internet site at http www LeicaBiosystems com HistoCore Arcadia C Cold Plate 2 Safety To prevent damage to the instrument or the specimen only accessories authorized by Leica Biosystems may be used 2 2 Warnings The safety devices installed in this instrument by the manufacturer only constitute the basis for accident prevention Operating the instrument safely is above all the responsibility of the owner as well as the designated personnel who operate service or repair the instrument To ensure trouble free operation of the instrument make sure to comply with the following instructions and warnings Warnings Safety notes on the instrument itself e This device may only be used by trained laboratory technicians It must only be operated for the purpose of its designated use and according to the instructions contained in these Instructions for Use e Safety notes on the instrument itself which are marked with a warning tri angle indicate that the correct operating instructions as defined in these Instructions for Use must be followed when operating or replacing the item marked Nonobservance can cause accidents injuries and or damage to the instrument accessori
9. ate Master Place one copy in the unit prior to packaging or hand it over to the service engineer Customer assumes all responsibility for the immediate return shipment of articles sent to Leica without proper decontamination documentation If you have any further questions please call your local Leica organization Leica Internal Use If applicable note corresponding Job and RAN RGA Number Job Sheet No Signature Date BU Return Authorization Number Name Po Position Ei eMail e Leica Biosystems Nussloch GmbH Phone 49 0 6224 143 0 Heidelberger Str 17 19 Fax 49 0 6224 143 268 69226 Nussloch Germany www LeicaBiosystems com 22 SU Return Goods Authorization Institute Department a Address Pod Eanna Phone Fax Ei Cicada AIRS YS TERS Instructions for Use V 1 2 Rev C 06 2015 Leica BIOSYSTEMS Leica Biosystems Nussloch GmbH Heidelberger Strasse 17 19 D 69226 Nussloch Tel 49 0 62 24 143 0 Fax 49 0 62 24 143 268 Web www LeicaBiosystems com
10. be considered a hazard by the Company they will be returned immediately to the customer at his her expense Note Microtome knives must be in boxes Mandatory information Fields marked with are mandatory Depending on whether the instrument is contaminated please also complete either section A or section B Nameplate information Model see nameplate SN see nameplate REF see nameplate mm Tick Box A if applicable Otherwise please complete all parts of B providing further information as requested or appropriate This equipment has not been in contact with unfixed biological samples gt BE 1 This equipment has been exposed internally or externally to hazardous materials as indicated below lt es Please provide further detail here Blood body fluids pathological samples Po Other biohazards SSS Chemicals substances hazardous to health SSS Dinar hazards 2 This equipment has been cleaned and decontaminated If yes give details of the method Please provide further detail here lf no please indicate why not EEE Such equipment must not be returned without the written agreement of Leica Biosystems UF LILILLIL CF OCOS Yes 3 The equipment has been prepared to ensure safe handling transportation Whenever possible please use the original transportation case box je HistoCore Arcadia C Cold Plate 21 9 Important to avoid refusal of shipment Decontamination Certific
11. e air circulation is not impaired The instrument must be installed in a place that ensures an easy disconnection from the power supply The power cable must be in a place that can be easily reached To ensure proper function and an easy disconnection of the power cable from the in strument there must be gap of at least 15 cm behind the instrument Failure to observe this distance may result in serious damage to the refrigeration unit of the device The instrument should not be operated in hazardous locations 42 Standard delivery packing list Oty Designation Order No Basic unit HistoCore Arcadia C 220 240 VAC 14 0393 53599 220 240 VAC China 14 0393 54102 110 120 VAC 14 0393 54092 100 VAC 14 0393 54091 Power cord See page 16 Sets of spare fuses 250 V 5A 14 6000 05015 Instructions for Use printed German English with language CD 14 0393 80200 140393 80001 1 Please compare the delivered components against the packing list and your order Should there be any discrepancy please contact the Leica Biosystems distributor handling your order HistoCore Arcadia C Cold Plate 13 4 Setting up the instrument 43 Unpacking and installation When the instrument is delivered check the tilt indicators on the packaging If the arrowhead is blue the shipment was transported laying flat was tilted at too great an angle or fell over during transport Note this on the shipping documents a
12. e an important part of the product and must be read carefully prior to startup and use and must always be kept near the instrument This instrument has been built and tested in accordance with the safety requirements for elec trical equipment for measurement control and laboratory use To maintain this condition and ensure safe operation the user must observe all notes and warnings contained in these Instructions for Use gt gt p gt m me These Instructions for Use must be appropriately supplemented as required by the exist ing regulations on accident prevention and environmental safety in the operator s coun try The protective devices on the instrument and its accessories must not be removed or modified Only service personnel qualified by Leica Biosystems may repair the instru ment and access the instrument s internal components Use only the provided power cable this must not be replaced with a different power cable If the power plug does not fit in your socket contact our service Residual risks The instrument has been designed and constructed with the latest state of the art tech nology and according to recognized standards and regulations with regard to safety technology Operating or handling the instrument incorrectly can place the user or other personnel at risk of injury or can cause damage to the instrument or other property The instrument may be used only as intended and only if all of its s
13. e instrument type indicated on the cover page A nameplate is attached to the back of the instrument and a serial number label is on the side of the instrument instrument with the necessary informa tion about instrument type and power reguirement The precise data for the various versions is specified in Chap ter 3 3 Technical data Fig 1 Intended use of instrument The HistoCore Arcadia C is a cold plate for chilling and blocking out histological tissue samples in paraffin blocks Any other use of the instrument will be considered as improper use Qualification of personnel e The HistoCore Arcadia C may be operated by trained laboratory personnel only e Alllaboratory personnel designated to operate this instrument must read these Instructions for Use carefully and must be familiar with all technical features of the instrument before attempting to operate it Instructions for Use V 1 2 Rev C 06 2015 2 Safety 21 Safety notes A The safety and caution notes in this chapter must be observed at all times Be sure to read these notes even if you are already familiar with the operation and use of other Leica Biosystems products These Instructions for Use include important instructions and information related to the oper ating safety and maintenance of the instrument These Instructions for Use ar
14. es Safety instructions Transport and installation e After unpacking the instrument it may only be transported in an upright position e Before connecting the device to a power source ensure that the voltage indicat ed on the type plate matches the voltage available at the place of installation e The unit must be connected only with the supplied power cable and only toa grounded power receptacle Do not use an extension cord e The power socket to which the instrument is connected has to be near the instrument and easily accessible 8 Instructions for Use V 1 2 Rev C 06 2015 2 Safety e The minimum voltage see Technical data must be maintained while starting the refrigeration unit The compressor needs a start up current of approx 25 A Astable power supply In accordance with the instrument s specifications is essential to its proper function ing Please ensure that your electrical installation fulfills these preconditions prior to installing the unit Nonobservance causes damage to the instrument e Switch off the instrument each time before servicing repairing or cleaning and pull out the power plug e Failure to observe the instructions specified by the manufacturer may result in damage to the protection provided by the instrument HistoCore Arcadia C Cold Plate 0 3 Instrument Components and Specifications 31 Overview instrument components Instrument front vie
15. loth e Avoid prolonged contact of organic solvents on the surface of the instrument Do not use xylol acetone or alcohol on the painted surfaces 6 2 Maintenance instructions Only Leica Biosystems service technicians are authorized to open the instrument for mainte nance and repair work Please observe the following points to ensure the instrument s reliable function over extended periods e Clean the instrument with care after each use e Regularly remove dust from the ventilation slots on the back of the instrument with a brush or vacuum cleaner e Enter into a service contract at the end of the warranty period For more information contact the relevant Leica Biosystems customer service organization 18 Instructions for Use V 1 2 Rev C 06 2015 7 Troubleshooting chased the instrument If you cannot solve your problem using the help in the following table please contact your Leica Biosystems customer service organization or the Leica Bosystems dealer from whom you pur Error condition The cold plate cannot cool down to the target temperature and the alarm beeps twice Possible causes Inadequate air supply to venti lation unit Or The cold plate is malfunc tioned Corrective action 1 Make sure that enough Space Is reserved between the wall and the instrument It must be at least 15 cm 2 Wait about 5 minutes and restart the instrument 3 If the problem persists
16. mmmmmmmmmmmmmmmmm mmmmmmrmmmmmmmmmmmmmmm mmmmmmmmmmmmmmmiH 6 1 4 Intended use Of INStrUMENL c ccescesessssesesseseesessesseseeseseeseesesausesseeessesensaeseeeesansesansanseeaneensess 6 15 Qualification OF personnel csc artenscscanien ictecceaauasetaraanedae tactsatasannacesieartannavotonssvenacsbantentandnedaysdeameacntin 6 SAE N arara E E AAA au cavanedtevaeseuavesvatuviuestisenntassanexesuesiexensevacsaetiacestte 7 2 APOC VOCE SS 7 DP ANANG ena E E E EE A s a 8 Instrument Components and Specifications cscssscsssseeseseseeeasseseseeseseesesesstaees 10 3 1 Overview instrument COMPONENTS cscsseescssssescsssrseesesessesesesesseseeesasseseeansusesasensesaeenses 10 32 Main features of the IST CIN OND Ge aniiascocstvacssnsssyaredqonsasbensdzauteantaxcenanslantbiciaaueehonachecensbaanleaesesbnadaans 10 6 Tecnica Daes rm 11 Setting up the instrument s ssssssnsssnussnsnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnunnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnae 13 41 PEC FOCUS CN oa E ia EE 13 42 Standard delivery packing liSt s senennnneneneenensnsenersrsnrsrvirerursnnnnsrnnnunursnrnrurunrnrnrsnrnrnrenrnrsrsnns 13 4 3 Unpacking and MNS CI ON scscadeenessnaecocsecissasne saerveaintadvesenasanecsaiacesugupanseieinanernpraesneussatnncivaesiniciaie 14 AA Moving TS WISE MIGIV ssanie ANNE 15 OE SIN rreraren E 16 OU AG NOI mm m wwu u wvwwwvvwwvwvwvwewvwwwwwvwvwvwwwwvwwvwvwvwwwwvvvwvuvvwwwvvvvvwwvwvwvwwwvvwv
17. nd check the shipment for possible damage g Fig 3 Fig 4 14 A These unpacking instructions only apply if the box is placed with the symbols facing upwards 1 Remove the packing strap 1 and the adhesive tape 2 2 Open the package Lift up and remove the carton wall 3 3 Remove the foam pads 4 one by one A The HistoCore Arcadia C always has to be transported upright and horizon tally It must not be inverted under any circumstances even for short periods or stored on one of its sides It is mandatory to observe a wait ing time of 4hours between the last transport and the first time the instrument is switched on The oil present in the compressor needs this time to flow back to its original location Instructions for Use V 1 2 Rev C 06 2015 4 Setting up the instrument 43 Unpacking and installation Continued i 4 Ensure that when removing the instrument 5 Ar ei from the pallet this is carried out by two people et w lifting four lower corners of the housing base DR yy pez oe N Fig 5 Ama 5 Place the instrument on a stable laboratory table 6 Remove the accessorles from the accessory box 6 on the base of the pallet Fig 5 e The packaging must be retained for a the duration of the warranty period To return the instrument follow the instructions above in reverse order Fig 6
18. ns for Use V 1 2 Rev C 06 2015 1 important Information 1 2 Symbols in the text and their meanings Continued Indicates the temperature range permitted for storing and transporting the package Minimum 29 C Maximum 50 C Indicates the temperature range permitted for storing the package Minimum 5 C Maximum 50 C Indicates the humidity range permitted for storing and transporting the package Minimum 10 r H Maximum 85 r H Tip n Tell indicator to monitor whether the shipment has been transported and stored in upright position according to your requirements With a pitch of 60 or more the blue quartz sand flows into the arrow shaped indicator window and sticks there permanently Improper handling of the shipment is immediately detectable and can be proven definitively In the Shockwatch system a precision glass tube shows shocks or impacts that are above a specified intensity through red coloration Exceeding a defined ac celeration g value destroys the surface tension of the liquid in the interior of the tube This causes the indicator tube to change color Indicates the item can be recycled where correct facilities exist HistoCore Arcadia C Cold Plate 5 1 Important Information 1 3 e Fig 1 is provided as an example only a and shows a valid nameplate for this 1 4 1 5 Instrument type All information provided in these Instruc tions for Use applies only to th
19. se rating 5A 250 V Before replacing the fuse always switch the instrument off and pull the power plug from the wall socket Only miniature fuses of the type specified in the chapter Technical data can be used To replace the fuse please proceed as follows 1 Use a screwdriver to open the fuse holder 9 and remove the fuses 10 Replace them with two new fuses of the same type Use the screwdriver to press the fuse holder back to its original location Reconnect the instrument to an AC power outlet and switch it on 17 6 Maintenance and Cleaning 61 Cleaning the instrument Switch off the instrument and pull out the power plug each time before cleaning N While handling cleaning materials ohserve the safety regulations of the manufacturer and the lab regulations valid in the country of use During cleaning do not allow any liquid to penetrate inside the instrument To prevent scratching the surface of the instrument do not use metallic tools with sharp edges under any circumstances Work surfaces e All common laboratory cleaning products suitable for the removal of paraffin e g Polyguard or xylene substitutes can be used to clean the work area e Use a dry lint free tissue paper to clean the condensed water on the cold plate Instrument and exterior surfaces e If necessary clean the painted exterior surfaces with a mild household cleaner or soapy water and wipe with a damp c
20. uring storage and transport Electromagnetic environment IEC 61010 classification Pollution degree IP protection class IEC 60529 Refrigeration unit Refrigeration capacity Safety factor Refrigerant HistoCore Arcadia C Cold Plate Time lag fuses 5 x 20 mm 2xT5A 250V 5 A max 25 A 20 C to 30 C 6 C 20 to 80 non condensing Up to 2000 m 5 C to 50 C 29 C to 50 C 10 to 85 non condensing Basic electromagnetic environment Protection class 1 2 IP20 158 W at 50Hz 185 W at 60Hz 3 R 134a 11 3 Instrument Components and Specifications 33 Technical Data Continued Compressor oil 150 10 5 ml Ester RL7H ISO 7 according to ASHRAE condensing temperature 54 4 C evaporating temperature 23 3 C Coolant 115g 2g Dimensions and weights Width 400 mm Depth 605 mm Height 385 mm Weight 30 kg 12 Instructions for Use V 1 2 Rev C 06 2015 4 Setting up the instrument 41 Site requirement At a room temperature of gt 30 C the working temperature of the cold plate of 6 C may not be reached at all points Stable vibration free laboratory table with horizontal flat table top as far as possible vi bration free ground No direct sunlight or strong temperature fluctuations Room temperature consistently be tween 20 C and 30 C Relative air humidity maximum 80 non condensing The instrument should be set up in such a way that th
21. w LEE Fig 2 1 Power switch 4 Heat sink 2 Refrigeration system inside 5 Port for power inlet 3 Cooling surface 6 AC fuses 32 Main features of the instrument e The instrument is distinguished by a simple modular design and a powerful refrigeration unit with precisely controlled cooling performance e The environment adaptive control module ensures the working temperature always stabilized at 6 C e High cooling performance ensures that the instrument s working temperature is reached quickly e Optimized temperature distribution in the cold plate prevents dripping condensation e The generously dimensioned cooling surface has room for around 60 blocks e Designed to be used with the HistoCore Arcadia H Paraffin Embedding Station 10 Instructions for Use V 1 2 Rev C 06 2015 3 Instrument Components and Specifications 3 3 Technical Data General data Voltage of power supply Instrument type Power supply voltage Order Number 220 240 VAC 50 60Hz 14 0393 53599 HistoCore Arcadia C 110 120 VAC 50 60Hz 14 0393 54092 100 VAC 50 60Hz 14 0393 54091 Fuse Nominal current Maximum start up current 5 s Environmental operating temperature range Operating temperatures Environmental relative humidity Environmental operating altitude Permissible temperature range during storage Permissible temperature range during transport Permissible humidity range d
22. wvvvvvvv 17 bl Swit hing the instrument OM caskesatatataatecsdtengsoiaedsasedenicousnieteiacissncetasanissaceteatiomasevarsiuiaataianians 17 b2 Replacing tne secondary T S siccsssececiasccceaineteesduvetacetajaiaornacazcteansaenisaeaverssnateerentaaaiolacvetnidans 17 Maintenance and Cleaning scsscssssscssssssessssssseseesessesaesessesseseeseesessesaesaesesstsaesarseesnsaneess 18 61 Cleaning the TVS UOTE a secaececcicacssezcercaeechaz cntanacacitsectsereasndacastenecatacacionecesnangtasnausndesanatasuanedieane 18 62 Maintenance instructions sesiascccsts crcicessatinassacnacssnsanneresadvennanevauariareerniaeenb me svenmenesenaenaddtes 18 Troubleshooting m m m m wwwwwwwwwwwwvwwwwewwwwawueewvwwwvwevwwvwwwwwwvwvwwwwwvvvwwwwwwvwwwwwvuvwv 19 Warranty and Service ccsssssssesssssessessssseseseesesseseeseesesaesesseesesaesasseesesaesassessesaeseeseesnsaeeees 20 Decontamination Certificate Master cc sssssssssssssssssssesssresssesseeerersessstensenanarseeeenenss 21 Instructions for Use V 1 2 Rev C 06 2015 1 Important Information 11 Naming conventions The full name of the device is HistoCore Arcadia C Cold Plate The device is called HistoCore Arcadia C to ensure that the Instructions for Use are well legible me 1 2 Symbols in the text and their meanings Warnings appear in a gray box and are marked by a warning triangle A Notes i e important user information appear in a gray box and
Download Pdf Manuals
Related Search