Home

maintenance - Pdfstream.manualsonline.com

image

Contents

1. Remove the spare key and store it in a safe place Your key can be duplicated only by obtaining a key blank from Polaris and mating it with your existing key The VIN and engine serial numbers are necessary for model identification when registering your vehicle and obtaining insurance or when replacement parts are required If your snowmobile is stolen these numbers are essential to its recovery and identification Dealer Imprint NOTES SECTION 2 SAFETY Operator Safety 00eee eee 12 27 Safety Decals and Locations 28 34 Section 2 describes safe vehicle operation and identifies warning decals and their locations SAFETY Operator Safety The following two pages identify signal words and symbols that appear in this manual Your safety is involved when these words and symbols are used Become familiar with their meanings before reading the manual The safety alert symbol on your snowmobile or in this manual alerts you to the potential for personal injury AWARNING Indicates a potential hazard that could result in serious injury or death ACAUTION Indicates a potential hazard that may result in minor personal injury or damage to the machine CAUTION Indicates a situation that may result in damage to the machine NOTE NOTE will alert you to important information or instructions IMPORTANT IMPORTANT will alert you to important information or instructio
2. 0 000 20 Weather Conditions 26 Owner Maintenance Program 96 Oxygenated Fuels 81 Park Braker tes aces Gaye Sines Vee Giese 69 Polaris Anti Theft System 170 Pollution 0 0 2 0 02 eee T Position Sensitive Shock 56 Premium Fuel Switch 81 82 Preservation of the Environment 7 8 Noise Level 2 7 Polttoon S3 reres ote eieren imi een 7 Rear Rear Scissor Stop RRSS 57 58 Rear Suspension 0 49 Rear Scissor Stop RRSS 57 INDEX Rear Torque Arm Adjustment SKS Models 53 Rear Torsion Spring Xtra 12 53 Recovery System 121 Removing the Side Bulbs 131 Reserve Capacity 08 82 Responsible Driving 14 25 Reverse Kit Maintenance 136 Reverse Operation 90 92 Reverse Accessory Kit 137 Reverse Electronic 91 92 Reverse Mechanical 90 Safety 20 ccc eee eee eee 11 36 Scissor Stop Rear Rear RRSS 57 58 Sediment Trap Service 116 Service and Warranty Information 170 Shock Absorber Components 45 Shock Valving 000 47 Shock Position Sensitive 56 Skag Replacement 147 Sags Sae coed shea EORR seagate x 147 Ski Alignment 0 00 145 Ski Skags cae of ieee hae revectoee es 147 Snowmobile Clothing 1
3. It s very important to use the correct spark plug for your machine A spark plug with a heat range too high will cause engine damage A spark plug with a heat range too low will cause excessive fouling and engine malfunctioning In selecting a spark plug heat range for production a manufacturer assumes that the engine will be operated under extreme heavy duty conditions and selects a spark plug that will protect the engine from internal damage if the purchaser actually does operate the engine in this manner This selection could cause the customer who normally operates the engine under medium or light duty to have spark plug failure Refer to your Owner s Manual Supplement for the specific spark plug to be used in your machine CAUTION A plug with a heat range too high will always cause engine damage if the engine is operated in conditions more severe than that for which the spark plug was intended 112 MAINTENANCE General Maintenance A new engine can cause temporary spark plug fouling due to the preservative added during the assembly process Avoid prolonged idle speeds which cause plug fouling and carbonization Use recommended spark plugs with the proper gap Refer to your Owner s Manual Supplement for specific information on your ma chine eSpark plug torque is 18 22 ft Ibs 2 5 3 kg m Always carry spare spark plugs in case of an emergency The spark plug condition indicates how well the engine is ope
4. 10 6 21 37 53 69 85 10 11 13 14 0 6 2 8 Wind Speeds Greater Little Danger Increasing Great Than 40 MPH Have For Properly Danger Danger Little Added Effect Clothed Person Danger From Freezing of Exposed Flesh 26 SAFETY Operator Safety WIND CHILL CHART C Estimated Wind Speed Actual Thermometer Reading C in KPH 5 0 5 10 15 20 25 30 35 40 Equivalent Temperature C 0 5 0 5 10 15 20 25 30 35 40 10 1 4 11 16 22 27 33 38 45 50 20 4 9 17 23 29 36 42 48 54 61 30 7 13 21 28 35 42 48 55 63 69 40 9 16 24 32 39 47 53 61 69 76 50 11 18 26 34 41 49 57 64 73 80 60 12 19 27 35 43 51 59 66 75 82 70 13 20 28 36 44 52 60 68 76 84 Wind Speeds Greater Little Danger Increasing Great Than 70 KPH Have Little For Properly Danger Danger Added Effect Clothed Person Danger From Freezing of Exposed Flesh 27 SAFETY Safety Decals And Locations NOTE Warning decals have been placed on the vehicle for your protection Read and follow the instructions on each decal carefully If any safety decal becomes illegible or comes off contact your Polaris dealer for a free replacement The part number is printed on the decal Clutch Cover Warning Decal 1 This warning dec
5. Worn damaged or malfunctioning components may cause serious injury or death Before starting the engine check all components to be sure of proper operation Read and Understand Your Owner s Manual Read the Owner s Manual completely and refer to it often We ve attempted to provide as much information as possible to alert you to the safety requirements of snowmobiling Check Throttle and Brake for Proper Operation The throttle and brake are the primary controls of your snowmobile If either should malfunction loss of control could result Make sure the throttle lever compresses evenly and smoothly The lever should immediately return to the idle position without binding or hesitation If the throttle does not function smoothly DO NOT start the engine Have the throttle serviced immediately The need for a properly functioning brake is critical Your snowmobile is equipped with the highest quality brake system available Check the brakes for correct operation before starting the engine Throttle Safety Switch Test the throttle safety switch system daily before the machine is operated 66 GETTING READY TO RIDE Check Before Starting Engine Hydraulic Brakes Properly functioning brakes are critical to your safety Always check the following items to assure proper operation before starting the engine Brake Lever Travel When the brake lever is squeezed it should move no closer to the handgrip than 1 2
6. 136 Clutch System 0 000 134 Clutches e Sse toes sa EEE 22 Coil Spring Options 56 Cold Weather Driveaway 22 Coolant aea si dace ate aes eae bo 120 Coolant Level 120 Cooling System Maintenance 121 Cooling System Bleeding 121 123 Cooling Engine 119 Crossing a Slope 0 20 Daily Storage 0 008 92 Decal Airbox 05 28 Decal Cargo Carrier 0 29 Decal Clutch Cover 28 Decal Electronic Reverse 32 Decal Operator Caution 34 Decal Operator Warning 32 35 Decal Passenger 2 30 Decal Pressure Cap 28 Decal Standard Reverse 31 Decal Track Warning 29 DGICETS roon aoe beet o E aie 82 Drive Belt Deflection 135 Drive Belt Installation 133 Drive Belt Removal 132 Drive Chain Tension 123 Electronic Reverse Belt Installation 133 Electronic Reverse Belt Removal 4 132 Emergency Starting 89 Emergency Stopping Procedure 88 89 Engine Break In 76 77 Engine Cooling 119 Engine Lubrication 77 Engine Oil 77 83 84 Engine Protection During SLOTALE oe eo ks a E 150 151 Engine Stop Switch 71 86 Engine Troubleshooting 164
7. After this E initial break in period the rapid wear will cease If excessive Hi fax wear Minimum Thickness occurs due to poor snow all except Xtra Lite conditions additional wheel kits are available from your dealer 7 16 1 1 cm Minimum Thickness Xtra Lite 148 MAINTENANCE Suspension Maintenance Loose nuts and bolts can reduce your snowmobile s reliability and cause needless repairs and down time Before beginning any snowmobile trip a visual inspection will uncover potential problems Check the following items on a weekly basis or before any long trip Check rear idler wheel bolts for tightness i Check rear idler adjusting bolt locknuts for tightness i Check front torque arm limiter strap condition y Check slide rail Hi fax condition greatly affects performance have your dealer replace when worn to minimum thickness i Check track tension beginning on page 140 i Lubricate grease all suspension components see pages 101 106 Check ski runner skag condition Extended Storage Off season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many components Cleaning and Preservation of Hood Chassis and Trim Proper storage starts with cleaning washing and waxing the hood chassis and plastic parts Wipe down remaining surfaces with a damp cloth Clean and touch up with paint any rusted or previously paint
8. Clear Operating Area 71 Engine Stop Switch 71 Lighting Check 71 Owner s Manual 66 Park Brake 08 69 Steering Inspection 70 Tether Switch 71 PATO s eeren a cee 66 Track Inspection 70 Belt Deflection Drive Belt 135 Belt Installation Drive Belt 133 Belt Installation Electronic Reverse 133 Belt Removal Drive Belt 132 Belt Removal Electronic Reverse 132 Belt Troubleshooting 163 Belt Wear Burn 163 Bleeding Cooling System 121 123 Brake Bleeding 127 Brake Components 125 Brake Fluid Replenishment 126 176 Brake Inspection Hydraulic 124 Brake Lever Travel 67 68 125 128 Brake Lever Mechanical 128 Brakes Seurasi Mew Pee e Pees 67 68 Bulb Replacement Headlight 130 Bulb Replacement Side Bulbs 131 Bulb Replacement Taillight 131 Carburetion 000 85 Carburetor Adjustments 118 Carburetor Information 118 Carburetor Protection During StOTAgE sce AS athe hve Se 151 Cargo Carrier 00 16 Chaincase Oil Level 109 Gearcase Oil Level WideTrak 110 Choke and Cable Lubrication 108 Clear Operating Area 71 Clutch Alignment and Offset 135 Clutch Center Distance
9. Features and Controls 36 41 This section illustrates the locations of your snowmobile s controls and features Section 4 The Perfect Fit 43 63 This section explains how to tailor the suspension and other features for an optimum riding experience Section 5 Getting Ready to Ride 65 71 This section explains procedures that must be performed before riding Section 6 Operation 000055 73 93 This section explains proper engine break in operation of features and operating procedures Section 7 Maintenance 95 155 This section defines your role and your dealer s role in your snowmobile s regular maintenance Section 8 Troubleshooting 157 166 This section is a quick reference guide to solving problems Section 9 Warranty 170 175 This section contains specific warranty information SECTION 1 HOW TO USE THIS MANUAL Important Notes for Drivers 6 Preservation Of The Environment 7 8 Vehicle Identification Numbers 9 Section 1 contains helpful information for owners and drivers and illustrates the location of important identification numbers that should be recorded in your Owner s Manual It also defines your role in protecting and respecting your environment while experiencing The Way Out HOW TO USE THIS MANUAL Important Notes For Owners And Drivers jn After reading
10. Inspect oil line condition at 2000 miles 3200 km Polaris oil filters are specially designed for use on Polaris products Use only Polaris replacement parts Edge models use an oil filter 3 that s built into the oil sending unit located in the bottom of the oil tank After changing the oil filter bleed the oil injection system of all trapped air See your dealer for instructions or have your dealer perform the filter change and bleeding operation for you NOTE The direction of the arrows indicates the direction of flow through the filters See page 77 for oil recommendations 117 MAINTENANCE General Maintenance General Carburetor Information The number stamped in the end of the main jet indicates the jet size The jet installed at the time of manufacture is not necessarily correct for your elevation It s your dealer s responsibility to make sure the correct main jet is installed CAUTION Carburetor adjustments should be performed only by a knowledgeable service technician at an authorized Polaris dealer using the proper tools procedures and specifications Carburetor Adjustments The frequency at which the carburetors are synchronized or balanced is important Properly adjusted carburetors can greatly improve engine performance fuel economy engine life and reliability If you notice any of the following the carburetor may need adjustment Hard starting Poor idle Overheated
11. POLARIS 2002 SNIWMOBILE odlety and Maintenance AWARNING Read understand and follow all of the instructions and safety precautions in this manual and on all product labels Failure to follow the safety precautions could result in serious injury or death PROPOSITION 65 WARNING Snowmobile engines discharge fuel and exhaust which contain chemicals known to the State of California to Cause cancer and birth defects or other reproductive harm onto the snow on which they operate Keep this engine properly tuned and avoid unnecessary idling and spillage during fueling ZAWARNING The engine exhaust from this product contains chemicals known to cause cancer birth defects or other reproductive harm What s the hottest thing on snow Our new web site It s designed just for YOU e Technical tips e New product introductions e Event schedules e Parts and Service Manual information e Exciting details about The Way Out Check it out www polarisindustries com owner POLARIS The Way Out NOTES WELCOME Thank you for purchasing a Polaris snowmobile and welcome to our world wide family of Polaris enthusiasts Polaris proudly produces an exciting line of recreational products including snowmobiles all terrain vehicles personal watercraft utility vehicles and Victory motorcycles We believe Polaris sets the standard of excellence for all snowmobiles manufactured in the world today
12. engine off will remove this tension and ease shifting This should only happen during the break in of a new belt or when the drive driven clutch center distance is too long If this is the case belt tension adjustments should be made by your dealer 90 OPERATION Reverse Operation Electronic AWARNING Reverse operation even at low speeds may cause loss of control resulting in serious injury or death To avoid loss of control always Look behind before and while backing Avoid sharp turns Shift to or from reverse only when stopped Apply throttle slowly This reverse will only activate if the engine is below 4000 RPM Make sure the vehicle is stopped and the engine is running at idle 1 Make sure the area behind you is clear 2 Push the yellow reverse button on the left hand control for one second and release The engine will automatically reduce RPM and start a reverse rotation A flashing reverse light on the instrument panel will indicate the machine is in reverse 3 Slowly apply the throttle until movement starts and until you are certain you are in reverse NOTE The maximum engine RPM will be 6000 when in reverse NOTE If the engine has stopped running the snowmobile will run forward the next time it s started 4 amp CAUTION To avoid personal injury and or engine damage do not operate the electric starter or pull rope starter while the engine is running 91 OPERATION Reverse Operation
13. push the jounce bumper down as far as it will go on the shock rod and test ride the machine The bumper will move up on the rod in direct relation to the amount of travel If the shock travel is full the bumper will be seated at the top of the shock Shock Absorber Components 1 Retainer 2 Shock Rod 3 Jounce Bumper 4 Body 5 Threaded Spring Preload Adjuster Nut 45 THE PERFECT FIT Front Suspension Adjustments Adjusting Front ShockSpring Preload Increasing spring preload will increase ski to ground pressure Decreasing spring preload will decrease ski to ground pressure When adjusting be sure springs on both the left and right sides of the machine are at the same adjustment To increase front shock spring preload grasp the spring and turn it to the right Turn it to the left to decrease preload In the illustrations at right B indicates high preload and C indicates low preload Increasing the spring preload too much may adversely affect the handling of the snowmobile and the performance of the rear suspension Decreasing the spring preload too much may allow the upper spring retainer to fall off Always leave at least one thread showing above the nut A ACAUTION Always leave one thread showing above the adjuster nut On models equipped with a plastic adjuster nut if the nut is unscrewed from the threaded body the nut will break 46 THE PERFECT FIT Front Suspension A
14. s responsibility to operate the machine safely Slow down Control becomes more difficult with two people on board More space is required to make turns and longer distances are necessary for stopping 24 SAFETY Operator Safety Responsible Driving Every snowmobile handles differently and even the most docile conditions may become dangerous if operators drive improperly If you re new to snowmobiling acquaint yourself with the machine and with what it will and won t do under various conditions Even seasoned drivers should spend some time getting the feel for a machine before attempting ambitious maneuvers i A snowmobile depends on the rider s body position for proper balance in executing turns traversing hills etc Always start on a smooth level area to begin building your operating experience Before allowing someone else use your snowmobile know the extent of their operating skills Check to see if they ve taken a snowmobile safety course and have an operator s certificate For their protection as well as yours make sure they take a snowmobile safety course Everyone can benefit from the course Don t jump your snowmobile Jumping may injure your back because of spinal compression The seat and suspension of your snowmobile have been designed to provide protection under normal riding conditions Your snowmobile is not intended for this kind of use Be courteous to oncoming traffic by dimming your hea
15. 1 2 cup Fuel flow should be steady and encompass the entire diameter of fuel line If not replace filter Incorrect clutching SEE YOUR DEALER Carburetor and fuel There s no adjustment to change power out pump put SEE YOUR DEALER Engine Faulty plug s Change plug s continually backfires Carburetor Dirt or ice in fuel system Deicer should be added to fuel at all times for assurance against fuel line icing Engine requires Poor gasoline or Replace with fresh winter fuel more than not enough fuel normal pulls to getting to engine start 166 NOTES 167 168 NOTES SECTION 9 WARRANTY Service And Warranty Information 170 Warranty ois ki cawiee nee asenniGew din 171 173 Polaris Extended Service Contract 174 175 Section 9 contains specific warranty information 169 WARRANTY Service And Warranty Information Polaris Anti Theft System The Polaris anti theft system monitoring program PATS is designed to aid owners of registered snowmobiles in recovery of stolen machines Administration 1 Polaris snowmobile owner reports theft A In addition to notifying the proper law enforcement offi cials the owner must call the Polaris warranty department United States 612 542 0500 Canada 204 925 7100 B Owners must provide their name address telephone num ber and the model and serial number of stolen machines 2 Polaris warranty will provide all dealerships with
16. Always wear an approved helmet and eye protection Be aware of the weather forecast and especially the wind chill A table is provided on page 26 for your reference To better enjoy your ride be prepared warm and comfortable 16 SAFETY Operator Safety Disabled Operators Safe operation of this rider active vehicle requires good judgement and physical skills Operators with cognitive or physical disabilities have an increased risk of loss of control which could result in serious injury or death Know the Limitations of the Machine and Your Skills as a Driver AWARNING High speed driving especially at night is dangerous and unwise and could result in serious personal injury or death Observe all state and local laws governing snowmobile operation They ve been established for your protection Always be alert and pay attention to the trail ahead of you Multiplying speed MPH by 1 5 will equal the approximate number of feet per second your machine travels If your speed is 40 MPH your machine is traveling about 60 feet per second If you look back for only two seconds your machine will travel about 120 feet If your speed is 60 MPH your machine will travel about 180 feet in two seconds Traveling at night requires extra caution Check headlight and taillight to ensure proper operation and don t over drive your headlight beam Always be able to bring your machine to a stop in the distance illuminated by
17. Ice and snow build up Warm the engine at least five minutes Take the drive belt off between track and the machine in extremely cold weather and warm it up tunnel Break machine loose from the snow Poor engine Check for carb and choke synchronization fouled plugs performance debris in the carbs and water ice or dirt in gas tank or fuel line Loading machines onto Skis may gouge into trailers and prevent the drivetrain from trailers spinning properly Use enough speed to drive the machine completely onto the trailer Push and pull it to finish loading if necessary Clutch malfunction Inspect clutch components See your dealer Slow easy clutch en Use fast aggressive throttle to engage clutch gagement 163 TROUBLESHOOTING Engine Troubleshooting CAUTION Unless you have experience and training in two cycle engine repair see your dealer if technical problems arise Erratic engine operating RPM during accelera tion or load variations Harsh drive clutch engagement Drive belt turns over Machine fails to move 164 Drive clutch bind ing Driven clutch malfunction Drive belt worn or too narrow Excessive belt sheave clearance Wrong belt for application Clutch alignment out of spec Engine mount bro ken or loose Transmission in neutral Clutch jammed Track jammed Chaincase sprocket or chain jammed or broken Disassemble drive clutch to inspect shift weights for wear a
18. See your dealer for more information IMPORTANT Track damage or failure caused by operation on ice or under other poor lubrication conditions will void the track warranty 143 MAINTENANCE Steering System Steering Inspection and Adjustment Each week or before a long ride check fasteners and tighten if necessary Specific fasteners that should be checked are marked with a in the following illustrations CRC Suspension With Rack Steering All Steering Except CRC 144 MAINTENANCE Steering System Ski Alignment AWARNING Improper ski alignment or adjustment may cause loss of steering control resulting in serious injury or death Do not attempt to change the ski alignment or camber adjustment See your Polaris dealer With handlebars in straight ahead position and with vehicle weight compressing the suspension measure from the straight edge of the skis at the center of the ski mounting bolt The measurement between the skis at point X should be 1 8 to 1 4 greater than at point Y NOTE If the skis are misaligned we recommend that your dealer correct the alignment since camber adjustment may also be affected CRC Suspension with Rack Steering 145 MAINTENANCE Steering System Edge IFS Steering System All other steering systems 146 MAINTENANCE Steering System Ski Skags AWARNING Worn skis and or
19. Store the bolt in the tool kit for future use Install the belt tensioner bolt and torque to 4 6 ft Ibs 133 MAINTENANCE General Maintenance Clutch System AWARNING All clutch maintenance and repairs must be performed by an authorized Polaris dealer Any unauthorized modifications to clutches such as adding or removing weights will void the warranty If you become aware of higher than normal clutch engagement an unusual vibration or an unusual shift pattern contact your dealer immediately Do not operate the machine until corrections have been made CAUTION Do not lubricate clutch bushings The bushings in the weights and rollers of Polaris clutches are made of a material that may be damaged if lubricated Clean clutch sheaves periodically to maintain optimum performance Inspect clutch sheaves for damage wear or belt residue Clean with non oil based cleaners such as isopropyl alcohol 134 MAINTENANCE General Maintenance Clutch Alignment and Offset Clutch center distance and alignment A are crucial to maintaining optimum performance See your Owner s Manual Supplement for the recommended offset between the drive and driven clutches with the belt removed The drive belt is a very important part of the drive system Belt width and length must match the center distance of the clutches and sheave width of the drive clutch For this reason Polaris rec
20. The suspension pivot shafts should be lubricated with Polaris Premium All Season Grease PN 2871066 at 500 miles 800 km initially every 1000 miles 1600 km after that and before off season storage each year Lack of lubrication affects your ride and the life of your suspension For detailed information about suspension lubrication and adjustments see your Polaris dealer NOTE The following illustrations are general representations Your model may differ Lubrication points are indicated by a x and for ward is to the left NOTE Models will M 10 suspension will be shipped with a supple ment that contains information specific only to that suspension Forward 102 MAINTENANCE Lubrication 103 MAINTENANCE Lubrication 104 MAINTENANCE Lubrication 105 MAINTENANCE Lubrication Suspension Lubrication X 10 EDGE 106 Lubrication Jackshaft Bearing Greasing Loosen the driven clutch retaining bolt and pull the clutch outward to expose the bearing and grease fitting Inject grease into the grease fitting in the flangette until grease purges from inside or outside the bearing seal may take only two pumps Push the clutch back onto the shaft and replace the clutch retaining bolt Torque to 18 ft Ibs 2 48 kg m Driveshaft Bearing Greasing Inject grease into the fitting on the speedometer drive adaptor until grease purges from inside or outside the bearing seal approximately t
21. a monthly updated list of all stolen units to further monitor thefts 3 Polaris warranty will aid in notification of recovered units to their proper owner Obtaining Service and Warranty Assistance Read carefully and understand the service data and the Polaris warranty contained in this manual Contact your Polaris dealer for replacement parts service or warranty He s constantly kept up to date on changes modifications and tips on snowmobile maintenance which may supersede information contained in this manual He s familiar with our policies and procedures and will be happy to assist you When contacting us about parts service or warranty always provide the following information 1 Serial number 5 Details of trouble experienced 2 Model number 6 Length of time and conditions of operation 3 Dealer name 7 Indicate previous correspondence 4 Date of purchase Use the space provided on page 9 to record the model and serial numbers of your machine and engine 170 WARRANTY LIMITED WARRANTY Polaris Industries Inc 1225 Highway 169 North Minneapolis Minnesota 55441 5078 gives a ONE YEAR LIMITED WARRANTY on all components of the Polaris snowmobile against defects in material or workmanship This warranty covers the parts and labor charges for repair or replacement of defective parts which are covered by this warranty This warranty begins on the date of purchase This warranty is transferrable to another consumer duri
22. assembly Depress the switch to stop the engine and vehicle Routinely check this switch for proper function with the engine idling The steering and braking ability are greatly reduced when operating on hard packed snow ice or when crossing roads Reduced speed and extra care are required to maintain vehicle control Carbide skags and studs enhance vehicle control on ice or hard packed surfaces Care must be taken to maintain a proper balance of ski carbides to track studs to maintain proper vehicle control See the Owner s Manual for proper use of traction accessories Never permit a guest to operate this vehicle unless the guest has read the Owner s Manual and warnings 33 SAFETY Safety Decals And Locations Caution Decal 9 The hood of your snowmobile contains a CAUTION decal The location of this decal will depend on which model you own 34 BEFORE STARTING ENGINE Check throttle and brake for proper operation Check to see that hood is securely latched Check surroundings to verify clear operation area Determine that steering is free and functional BRAKE LEVER LOCK May relax when used for long periods Do not leave brake engaged for more than five minutes ALWAYS Be seated and in position to control vehicle Stop engine before attempting adjustments Know the limitations of the vehicle and your skills as a driver Understand your Owner s Manual Wear clothing designed for snowmobiling Stops from hig
23. engine and cooling system Coolant High Temperature Indicator Light The high temperature indicator light is controlled by a switch in the engine cooling system If the engine coolant reaches a certain temperature the switch completes a circuit that turns the light on If you must drive your machine after the high temperature indicator light has come on drive slowly and stop frequently to allow the engine to cool down See your dealer Coolant Level The engine coolant level is controlled by the recovery system The recovery system components are Coolant tank or overflow tank Engine filler neck Pressure cap on some models e Connecting hoses CAUTION The coolant level in the reservoir or surge tank must be maintained between the minimum and maximum levels to prevent overheating and serious engine damage Some models require the coolant level be maintained at the full cold line on the coolant tank when the engine is cold 120 MAINTENANCE General Maintenance Flushing the Cooling System To ensure that the coolant maintains its ability to protect the engine the system should be completely drained every two years and a fresh 50 50 or 60 40 mixture of antifreeze and distilled water should be added This service must be done when the engine is cold Ask your Polaris dealer to check the coolant when he performs the fall tune up on your snowmobile Bleeding the Cooling System AWARNING Steam and hot liquids bu
24. is still required on such surfaces Steering ability may be reduced on hard packed snow or ice A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmobile and to prevent ski wear caused by contact with roads and other bare terrain The addition of carbide skags is recommended with studded tracks to help maintain proper vehicle steering and control Similarly if your machine is equipped with carbide skags or you re adding them it may be necessary to add track studs to maintain proper vehicle control Proper balance must be maintained between the number of studs and the length of carbide on skags The more studs used the longer the carbide on the skags should be See your dealer s track studding chart for recommended studding and skags Inspect skags and studs frequently Worn studs or skags may reduce steering and braking control on hard packed snow and ice Replace worn studs and skags to maintain proper balance and vehicle control When studded tracks are used increased wear to the brake pads will result from increased braking Extended wear brake pad kits are available See your dealer for more information CAUTION Aggressive studding patterns may require grinding protruding stud bolts flush to prevent idler wheel damage Maintain track tension on studded tracks on the tight side of the spec to prevent heat exchanger damage Center of stud must be at least 1 1 8 2 86 cm from the edge
25. is tightened it will open the sheaves loosening the belt to the point where it can be easily removed 3 Grasp the belt firmly midway between the clutches and pull upward and rearward Remove the belt 4 Ifa belt is not going to be immediately reinstalled reinstall the tensioner bolt and store the 1 1 2 bolt in the tool kit of the machine 132 MAINTENANCE General Maintenance Standard Belt Installation 1 4 Drop the drive belt over the drive clutch and pull back the slack A NOTE To ensure satisfactory belt life install belts so they operate in the same direction of rotation by positioning the identification numbers so that you can read them Turn the driven clutch moveable sheave clockwise while pushing inward and forcing the belt down between the sheaves Hold the belt down between the sheaves and roll the bottom portion over the outer clutch sheave B Work the belt to the outer edge of the sheave Release parking brake if it s locked Close the clutch guard and reinstall the retaining knob or pin Electronic Reverse Belt Installation 1 2 If the 1 1 2 bolt is not in place install it to separate the sheaves Drop the drive belt over the drive clutch and pull back the slack NOTE To ensure satisfactory belt life install belts so they operate in the same direction of rotation by positioning the identification numbers so that you can read them Remove the bolt to tighten the sheaves
26. light is on oil should be added before further operation of the snowmobile Visually check the oil level in the bottle The engine may be operated as long as oil is visible in the oil tank If oil is not visible continued operation may cause serious engine damage Never mix brands of two cycle oil Serious chemical reactions may occur causing injection system blockage This may result in serious engine damage and the voiding of engine warranty Always maintain the oil level above the tank s low level line This is especially important when the machine is operated in mountainous terrain Maintaining the proper oil level will prevent system aeration and possible loss of pumping action which could result in engine damage 83 OPERATION Oil Low Oil Level Always do a visual check of the oil level when refueling In the illustration indicates a low oil level When the oil reaches the low level mark add one U S quart of oil to the tank Always use a Polaris oil cap never substitute Your Polaris oil cap may be vented to allow proper oil flow NOTE Not all models have a coolant bottle attached to the oil tank 84 OPERATION Carburetion Proper carburetor adjustment is critical A lean mixture too much air too little fuel may result in piston burning bearing failure or complete engine failure A rich mixture too much fuel too little air may foul plugs and cause generally poor engine performance A lean mi
27. of the outer belt 62 THE PERFECT FIT Accessories Wear Strips To avoid excessive tunnel wear tunnel wear strips must be installed whenever track studding is used Several wear strips are available See your dealer for more information Some models are manufactured with tunnel wear strips or wear strip coolers installed Refer to your Owner s Manual Supplement to determine if your model has wear strips Wear strips are designed for a specific stud length See your dealer s studding chart for recommended traction accessories Components as viewed from the rear of the track 1 Top of tunnel 2 Wear strip 3 Track 4 Wearstrip mounting holes CAUTION Studs longer than 1 2 5 cm on machines equipped with center coolers will cause center cooler damage Whenever wear strips are relocated be sure there s adequate stud clearance to the heat exchangers Lack of clearance may result in damage to heat exchangers 63 NOTES SECTION 5 GETTING READY TO RIDE Check Before Starting Engine 66 70 Throttle Freeplay Brake Fluid Levels eSteering Mirrors Gear Start the Engine and Check 71 eLights eStop Switch Skis and Track cold warm Pre ride warm up Certain items must be checked before each ride This section explains procedures that must be performed before riding 65 GETTING READY TO RIDE Check Before Starting Engine AWARNING
28. patented carburetor bowl water sediment traps located at the bottom of each carburetor The trap consisting of a hose with a plug should be drained at least every 2000 miles 3200 km and inspected for contamination AWARNING When draining the traps fuel spillage will occur Always work in a well ventilated area away from anything that may cause the fuel to ignite such as open flames sparks heaters trouble lights cigarettes etc Review the gasoline warnings found on page 80 Plug Cleaning Procedure 1 Turn the fuel tank supply valve off 2 Position a container or shop towels to catch the contaminated gasoline 3 Slide the clamp 1 away from the drain plug 2 and remove the drain plug from the sediment tube 4 Wipe residue from the plug and reinstall it Reposition and tighten the clamps Continue until all the traps have been emptied 116 MAINTENANCE General Maintenance Fuel Filter Fuel Lines CAUTION The in tank fuel filter 1 and fuel lines should be inspected regularly Give special attention to the system s fuel line condition after periods of storage Normal deterioration from weather and fuel compounds may occur Do not use pliers or a similar tool to remove fuel lines as damage may occur Do not kink the fuel line as damage may occur If a fuel line has been damaged or kinked replace it promptly Oil Filter The oil filter should be changed annually or every 1200 miles 1920 km
29. position etc until the best ride is achieved Adjustments should be made to one area at a time in order to properly evaluate the change All snowmobile suspensions have a front and a rear suspension each of which has adjustment options Independent Front Suspension IFS The IFS is made up of the skis 1 front shocks and springs 2 and the components that connect these parts to both the steering such as the radius rods 3 and to the machine itself such as the trailing arms 4 Front suspension adjustment options are limited to the front shocks and springs NOTE Although the front suspension on your machine may not look exactly like the illustration it will have the same parts and functions as those illustrated IFS Adjustment Options Front shock spring preload Optional springs Optional valving if equipped with RYDE FX or Fox Shocks eIndy Select if equipped 44 THE PERFECT FIT Front Suspension Adjustments AWARNING Always verify ski alignment before making adjustments to the IFS See page145 to check alignment If the skis are misaligned see your dealer as the camber adjustment may also be affected The tension at which the shock coil spring is set is called spring preload For the best ride the spring preload should be set as low as possible to use the full travel of the ski shock with occasional light bottoming To determine if your machine is using full travel of the ski shock
30. steering linkage Make sure all greasable components are properly lubricated Track Inspection AWARNING Always inspect the track for damage before using the vehicle Operating the snowmobile with a damaged track increases the possibility of track failure which could cause loss of control resulting in serious injury or death Use of traction products such as studs increases the possibility of track damage and or failure Driving at high speeds for extended periods of time in marginal lubrication could severely damage track rods break track edges and cause other track damage Examples of marginal lubrication would include frozen bodies of water without snow cover icy trails and no snow conditions NOTE Track damage or failure caused by operation on ice or poor lubrication conditions voids the track warranty Check for Securely Latched Hood The hood of the snowmobile protects the operator from moving parts as well as aiding in sound emission control and other functions Under no circumstances should your snowmobile be operated with the hood open or removed 70 GETTING READY TO RIDE Start The Engine And Check jn jn od jn Transmission Make sure the reverse is not engaged before starting your machine Engine Stop Switch Check the auxiliary shut off switch for proper operation Push down to stop the engine Pull up to release and start the engine Tether Switch If equipped check the tether switch for
31. the spark plug while the engine is warm Remove the spark plug with the special wrench 1 provided in the tool kit 1 Remove the spark plug cap 2 Rotate the plug counterclockwise and remove it 3 Install the new spark plug rotating clockwise 4 Torque to 18 22 ft lbs 2 5 3 kg m 5 Check spark plug gap refer to your Owner s Manual Supplement 6 Install spark plug cap 114 MAINTENANCE General Maintenance Variable Exhaust System V E S Maintenance of the V E S is limited to a periodic inspection and cleaning of system components Every 1000 to 2000 miles bring the machine to an authorized Polaris dealer to have the V E S disassembled inspected and cleaned NOTE To ensure maximum performance and minimize required maintenance follow the oil recommendation chart on page 77 The use of other lubricants may cause improper function of the valve mech anism and increase the frequency of required cleaning due to excessive build up of carbon deposits Water Pump Belt Inspection Some liquid cooled models require inspection of the water pump belt at 1500 miles 2400 km Inspect belt width A and condition and replace if cracked or worn past the width service limit 250 6 35mm New belt width is approximately 345 8 75 mm See your Polaris dealer if the belt needs to be replaced 115 MAINTENANCE General Maintenance Water Sediment Trap Service Most Polaris snowmobiles contain
32. this manual store it in the snowmobile for convenient reference It should remain with the snowmobile when sold This manual contains the latest information at the time of printing We reserve the right to make product changes and improvements without notice The illustrations and photos used in this manual are general representations Your model may differ Follow the maintenance program outlined in this manual Preventive maintenance ensures that critical components of the snowmobile are inspected by your dealer at specific mileage intervals You and your dealer must complete the registration form included with your snowmobile and forward it to us This completed form is necessary to ensure warranty coverage Protect and preserve your right to ride by joining your local trail riding clubs HOW TO USE THIS MANUAL Preservation Of The Environment Please operate your snowmobile with consideration for the protection and preservation of our environment Noise Level One of the most publicized issues about snowmobiles is noise The Society of Automotive Engineers SAE the standard setting body for snowmobile development recommends that snowmobiles conform to prescribed sound levels Polaris snowmobiles are engineered to conform to these SAE standards Our muffler systems are designed to reduce noise levels and must not be altered or removed The sound of your snowmobile may not be welcome to non snowmobilers so you have a res
33. to the transporting unit securely using suitable straps 152 MAINTENANCE Battery AWARNING Battery electrolyte is poisonous It contains acid Serious burns can result from contact with the skin eyes or clothing If contact occurs seek immediate medical attention KEEP OUT OF REACH OF CHILDREN EXTERNAL Flush with water INTERNAL Drink large quantities of water or milk Follow with milk of magnesia beaten egg or vegetable oil Call physician immediately EYES Flush with water for 15 minutes and get prompt medical attention Batteries produce explosive gases Keep sparks open flames cigarettes etc away Ventilate when charging or using in closed space Always shield eyes when working near batteries Battery Fluid A poorly maintained battery will deteriorate rapidly Check the battery fluid level often The fluid level should be kept between the upper 1 and lower 2 level marks 153 MAINTENANCE Battery Battery Connections Keep battery terminals and connections free of corrosion When cleaning is necessary remove the corrosion with a stiff wire brush Wash terminals and connections with a solution of one tablespoon baking soda and one cup water Rinse well with tap water and dry with clean shop towels Coat the terminals with dielectric grease or petroleum jelly CAUTION Tap water contains minerals that will damage a battery and shorten its life Use only distilled water
34. trail riding B Medium or High Position standard fop hole location This setting will A decrease weight transfer C Rearward Upper Position optional hole location This setting will increase weight transfer NOTE Your dealer can help you with initial set up and additional set up instructions to help you achieve your optimum ride Xtra 12 Rear Rear Scissor Stop RRSS The RRSS on Xtra 12 suspensions is not adjustable 58 THE PERFECT FIT Handlebar Adjustment Follow these steps to adjust the handlebars for a personal fit 1 Remove the handlebar cover to expose the handlebar and the four adjuster block bolts A 2 Using a 7 16 11 mm wrench loosen the four nuts on the bottom of the adjuster block turn handlebar to left or right for access to back nuts NOTE It may be necessary to pry the adjuster blocks apart with a screw driver 3 Adjust the handlebar to the desired height Be sure handlebars brake lever and throttle lever operate smoothly and do not hit the gas tank windshield or any other part of the machine when turned fully to the left or right 4 Torque the handlebar adjuster block bolts to 11 13 ft Ibs 1 5 1 8 kg m 5 Replace handlebar cover Backrest Adjustment The passenger backrest on some models is adjustable To move the backrest forward or backward lift the adjustment lever on the left side 1 When adjusting the backrest from a passenger position to a sing
35. 1 3 cm A A distance less than this indicates low brake fluid level or air in the hydraulic system Refer to the brake bleeding information on page 127 Lever Feel A hydraulic system multiplies the force of your hand squeezing the brake lever Proper operation depends on an adequate supply of air and moisture free hydraulic brake fluid in the system If the brake lever feels spongy when squeezed check the level and condition of the fluid Also check for the presence of air in the fluid system Refer to page 127 for more information or see your dealer for service Replace brake fluid at least every two years with Polaris DOT 3 high temperature brake fluid All DOT 3 brake fluid is not alike Use only Polaris brake fluid PN 2870990 AWARNING Continued use of spongy brakes may cause a complete loss of brakes which could result in serious injury or death 67 GETTING READY TO RIDE Check Before Starting Engine Mechanical Brakes Brake Lever Travel Firmly depress the brake lever Measure the distance A between the lever and brake block The distance should be no more than 3 4 1 9 cm If the distance is greater than this recommendation the brake cable must be adjusted Refer to mechanical brake adjustment information on page 128 68 GETTING READY TO RIDE Check Before Starting Engine Park Brake Lever Lock Your snowmobile may have a park brake lever lock located over the brake le
36. 166 Exhaust System 119 Exhaust System Variable Exhaust 115 Extended Service Contract 174 175 Peatures orie see ile eed 39 43 Features and Controls 35 43 Filter Air Intake 111 Filter Fuel 200 117 Filter Oil eeen a gai pte BY ae ee 117 Flushing the Cooling System 121 Front Shock Spring Preload Adjustment 46 Front Suspension 44 Front Rear Scissor Stop FRSS 56 Buel ost oad e OAE ERA atens 80 82 F el Pulte to otis cease at enmane acti 117 Fuel Linesa ersari areca s pEi 117 Fuel Reserve 0 000 82 Fuel System Deicers 82 Getting Ready to Ride 65 73 Greasing Couplers Wide Trak 107 Greasing Driveshaft Bearing 107 Greasing Jackshaft Bearing 107 Handlebar Adjustment 59 Hard Packed Snow 19 Headlight Adjustment 129 Headlight Bulb Installation 130 Headlight Bulb Removal 130 Hi Fax Wear 00 0 148 High Temperature Indicator Light 120 Hydraulic Brakes 67 Independent Front Suspension IFS 44 Indy Select Front Track Shock 54 Indy Select Shock 0 55 Indy Select Shock Front 48 Indy Select Shock Rear 54 Indy Select Rear 00 55 Inspection Hydraulic Brakes 124 Inspection Steering 144 Inspect
37. 6 Spark Plug Removal 114 Spark Plug Selection 112 Spark Plug Normal 113 Spark Plug Overheating 113 Spark Plug Wet Fouled 113 Spring Tension Rear 50 51 Springs Coil 0 0 0 2 eee 56 Starting a Cold Engine 74 75 Electric Start senise eiseni pacatis 75 Starting a Warm Engine 75 Starting Procedure Emergency 89 Steering Inspection and Adjustment 144 Steering System 144 147 Stop Switch 0 sereni ientra 86 Stopping Procedure 88 Stotage og Peter ose sess 92 149 152 Battery ene ike Sede ee ew eines 151 Bearings ees ce sew ee ee Sees 150 Cleaning he e325 ese e ee eS 149 Clutch and Drive System 150 Controls and Linkage 149 Electrical Connections 151 Track and Suspension 152 178 Supplies 0 0 0000 139 Surge Tank 00 122 123 Suspension Adjustment Features 44 Suspension Adjustment EDGE RMK 50 Suspension Adjustment Xtra 10 EDGE Xtra Lite 52 Suspension Coupling 56 Suspension Lubrication 101 107 Suspension Maintenance 148 149 Suspension Performance Tips 49 Suspension Troubleshooting 158 162 Suspension Front 44 Suspension Rear 0 49 Taillight Bulb Replacement 131 Temperature Indicator 120 Tension Drive Ch
38. AWARNING When driving on long downhill stretches pump the brakes Riding the brakes may cause the brake system to overheat which may result in brake failure Excessive or repetitive use of the brakes for high speed stops will also cause an overheated brake system This condition may lead to a sudden loss of brakes and or fire and may result in serious injury or death Do Not Operate Engine With Clutch Guard Removed The clutch guard is designed to protect the operator from metal parts if the clutch should fail Although the chance of failure is extremely remote don t defeat the purpose of the guard by removing it It s provided for your safety Do Not Operate Engine With Drive Belt Removed Any servicing that requires operation without a belt must be performed by your dealer Operation of the engine with the belt removed may result in personal injury or damage to the engine 21 SAFETY Operator Safety Do Not Operate Engine With Intake Silencer or Filter Removed Damage to the engine may occur if the intake silencer or filter are removed Do Not Service Clutches Yourself All clutch service must be performed by your dealer The clutch is a complex mechanism that rotates at high speeds Each clutch is dynamically balanced before installation Any tampering may disrupt this precision balancing and create an unstable condition Cold Weather Drive Away Whenever your snowmobile has been parked for a length of time e
39. Electronic Forward When running in reverse again push the yellow reverse button on the left hand control for one second and release The engine will slow and and begin to rotate forward The light on the instrument panel will shut off Make sure the area around you is clear and apply throttle slowly until you re certain you re going forward NOTE If the engine has stopped running the snowmobile will run forward the next time it s started Altitude Setting At higher altitudes above 6000 feet the engine will require a different ignition setting to improve the success of this reverse system To set for higher altitude start the engine and hold the button down until the light on the instrument panel flashes rapidly then release the button This is the setting for higher elevations To set the reverse for lower elevations remain holding the button down until the reverse indicator light blinks slowly Once set it s held in memory until changed whether the machine is running or not Daily Storage At the end of your ride park the snowmobile on a level surface and support it at the rear with the appropriate track stand The track should be suspended approximately 4 20 cm off the ground Remove the key and cover the machine NOTE Polaris has accessory covers and track stands avail able to fit all models See your dealer for more informa tion 92 OPERATION Towing For your safety the prop
40. HH 97 MAINTENANCE Maintenance Chart Weekly or 150 M 1000 M 2000 M See before 240 km 1600 km 3200 km Page long trip Tighten idler adjusting bolt jam X 142 nuts Core Ya Inspect coolant filter replace if necessary Grease ski pivots Sa x Grease ski spindles e a a Grease center steering arm s Rae Gales ea Lubricate steering post support bracket and pivot aerosol Check cylinder base stud torque on all Polaris engines Specifica tion 32 ft lbs 2 ft lbs Dealer Grease lower steering post pivot in x Grease driveshaft bearing always peitori before storage Grease rear suspension pivot 107 shafts Grease jackshaft bearing always perform before storage Lubricate throttle cable Eo o ae mae aae e e e Creer eruen alignment oi __ x x 54 a es o a a e esis gravity e Ya EA Inspect exhaust system for weak or missing retaining springs Inspect exhaust pipe for cracks or damage Inspect clutch sheaves for X 134 damage wear belt residue 98 f Eii Aed gt P lt gt lt HH Lf MAINTENANCE Maintenance Log Present this section of your manual to your dealer each time your snowmobile is serviced This will provide you and future owners with an accurate log of maintenance and services performed on the snowmobile 150 Mile 240 km Initial Maintenance Inspection Authorized Polaris Servicing Dealer Servicing Technician Date Mile
41. Many years of experience in engineering design and development have gone into making your Polaris snowmobile the finest machine we ve ever produced Follow the instructions and recommendations in this Owner s Manual for safe and enjoyable operation of your vehicle Your Owner s Manual contains instructions for minor maintenance but major repairs are covered in the Polaris Service Manual and should be performed by a Factory Certified MSD Master Service Dealer Technician Your Polaris snowmobile dealer knows your vehicle best and is interested in your complete satisfaction Return to your dealership for all of your service needs during and after the warranty period Polaris also takes great pride in our PAA Parts Apparel and Accessories which are available on our online store www purepolaris com Have your accessories and clothing delivered right to your door Polaris and Polaris The Way Out are registered trademarks of Polaris Industries Inc Copyright 2003 Polaris Industries Inc All Rights Reserved Printed in the U S A TABLE OF CONTENTS Section 1 How to Use This Manual 5 9 This section contains helpful information for owners and drivers and illustrates the location of important identification numbers that should be recorded in your Owner s Manual Section 2 Safety 0 00eeee 11 34 This section describes safe vehicle operation and identifies warning decals and their locations Section 3
42. Y Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you if inconsistent with controlling state law How to Obtain Warranty Service If your snowmobile requires warranty service you must take it to a Polaris dealer authorized to repair Polaris snowmobiles When requesting warranty service you must present your copy of the Warranty Registration form to the dealer THE COST OF TRANSPORTATION TO AND FROM THE DEALER IS YOUR RESPONSIBILITY Polaris suggests that you use your original selling dealer however you may use any Polaris Servicing Dealer to perform warranty service Please work with your dealer to resolve any warranty issues Should your dealer require any additional assistance they will contact the appropriate person at Polaris This warranty also gives you specific legal rights and you may also have other rights which vary from state to state If any of the above terms are void because of state or federal law all other warranty terms will remain in effect Engine Oil 1 Always use Polaris engine oil 2 Never substitute or mix oil brands as serious engine damage and voiding of warranty can result 173 WARRANTY Polaris Extended Service Contract Polaris extended engine service contract provides these benefits Additional engine protection beyond the original twelve month war ranty Backed by the strength of Polaris no third party involveme
43. age 1000 Mile 1600 km Maintenance Inspection Authorized Polaris Servicing Dealer Servicing Technician Date Mileage 2000 Mile 3200 km Maintenance Inspection Authorized Polaris Servicing Dealer Servicing Technician Date Mileage 99 MAINTENANCE Maintenance Log Additional Services Performed Authorized Polaris Servicing Dealer Servicing Technician Date Mileage Type of Service Additional Services Performed Authorized Polaris Servicing Dealer Servicing Technician Date Mileage Type of Service 100 MAINTENANCE Lubrication Lubricate the suspension and steering components with Polaris Premium grease PN 2871066 annually or about every 1000 miles 1600 km The illustration shows the location of suspension and steering components The in the illustration indicates a grease point or fitting Grease left and right spindles Raise the front end of the machine to permit better grease entry into the spindle area Lubricate both front ski pivots at fitting as shown Grease jackshaft and driveshaft clutch side bearings Use an aerosol lubricant on the steering post support bracket Grease center steering arms Grease steering post lower pivot Rear suspension pivot shafts Raise the rear of unit A grease gun kit complete with grease and adaptors PN 2871312 is available to lubricate all fittings on Polaris snowmobiles oy ft thaw a Aerosol a Rel Peek 101 MAINTENANCE Lubrication
44. ain 123 Tether Switch 0 008 71 The Perfect Fit 0 43 65 Throttle Cable Lubrication 108 Throttle Lever 0 000 87 Throttle Safety Switch 86 ToolKit i608 sco he cb ange os gies be oi 138 Tool Pouch Clip 138 Torque Arm Rear SKS Models 53 Torque Stop 000 136 Torsion Spring Adjustment Xtra 12 3 TOWING lt 8505 aces ce Rae og Soc ea wk 93 Track Alignment 142 Track Inspection 143 Track Lubrication 143 Track Tension 140 141 Track Warm Up 0 78 79 Traction Products 61 62 Transporting 00 152 Troubleshooting 157 168 Troubleshooting Belt 163 Troubleshooting Engine 164 166 TUNE DS oS cxsc odes ts eee ae 139 Variable Exhaust System 115 Vehicle Identification Numbers 9 Vehicle Nomenclature 9 Warranty 0000 169 175 Water Pump Belt Inspection 115 Water Trap Service 116 Wear Strips 2 0 0 eee eee 63 Weight Transfer 00 58 Windchill Temperature Charts 26 LARIS The Way Out D Part No 9916649 Rev 02 PRINTED IN THE USA
45. al is found under the hood on the clutch cover Do not operate engine with hood open Do not attempt adjustment with engine running Do not operate engine with this guard open Never run engine with drive belt removed Never service clutches yourself see your dealer Airbox Warning Decal 2 This warning decal is found under the hood on specific models Do not operate above 40 mph with hood to airbox foam removed or engine failure will result Pressure Cap Warning Decal 3 This warning decal is found under the hood near the pressure cap of specific liquid cooled models Release pressure before removing cap Cooling fluid must be up to the base of the pressure cap in hot or cold conditions Refer to the Owner s Manual for fluid level in overflow bottle 28 SAFETY Safety Decals And Locations Track Warning Decal 4 The track warning decal is on the rear of the tunnel 4 Stay clear of track Do not sit on seat back or cargo area Combined cargo and tongue weight should not exceed 40 Ibs 18 kg Cargo load affects machine steering response OR Stay clear of track Do not sit on seat back Entanglement with the track or a fall from seat back may result in severe injury or death Cargo Carrier Warning Decal 5 Machines with a cargo carrier will have this warning decal on the rear rack or on the taillight Do not sit in or on cargo area Cargo load should not exceed 40 Ibs 18 k
46. ase front and rear track shock compression damping by turning screw clockwise Rides too stiff in Check for binding suspension shafts and grease all pivot points rear Decrease spring preload adjustments Remove rear track shock spring or reduce rate of spring see your dealer Change front track shock to lighter spring Decrease front and rear track shock compression damping by turning screw counter clockwise Machine darts from Make sure skis are aligned properly side to side Make sure spindles and all steering components are free turning Ensure use of E Z Steer skags Check Hi fax and replace if worn Front end pushes Check for worn skags Check for binding suspension shafts and grease all pivot points Increase front IFS preload by adjusting threaded preload collar Move FRSS to low position or move to forward hole Steering is heavy Check ski alignment Check skags and skis for damage Decrease IFS spring preload Make sure spindles and all suspension components are free turning Reduce ski pressure Increase front track spring preload Reduce IFS spring preload by adjusting threaded preload collar Setting up for deep Rotate FRSS to lowest setting depending upon rider preference snow operation Decrease preload on front track spring Tighten limiter strap one hole Move FRSS to forward most hole 159 TROUBLESHOOTING Suspension Troubleshooting X 10 and Edge Solution perform only one change at a ti
47. aterial Replace when thickness is less than 1 16 Excessive Lever Travel Hydraulic brakes are self adjusting but if excessive brake pad clearance develops as described on page 124 the machine should be returned to an authorized Polaris dealer for inspection and adjustment 125 MAINTENANCE General Maintenance Replenishing Brake Fluid AWARNING After opening a bottle of brake fluid discard any unused fluid Do not store or use a partial bottle of brake fluid The fluid is hygroscopic meaning it rapidly absorbs moisture from the air The boiling temperature of the brake fluid will drop leading to early brake fade and the possibility of serious injury Keep the master cylinder cover free of dirt and debris The vent slits allow for diaphragm movement and if they become plugged movement of brake fluid below the diaphragm may be restricted altering brake function CAUTION Brake fluid will damage decals paint and some plastics Wipe up spills immediately Frequently check the reservoir to be sure it contains the correct amount of fluid Remove the brake master cylinder reservoir cover Add Polaris brake fluid PN 2870990 as required to bring the level up to the top of the fluid level mark on the inside of the reservoir The proper fluid level is 1 4 5 16 6 8 cm below the lip of the reservoir opening on most models NOTE On some models the brake fluid level can be seen through a plastic sight glass in t
48. bar Grip Warmer Switch 4 Thumbwarmer Switch 5 Electronic Reverse Button 6 Electronic Shock Control Button 7 Tether Switch wh FEATURES AND CONTROLS Location of Controls NOTE Some Polaris snowmobiles are equipped with special features Controls for these features are illustrated on this page Not all models come with these features Refer to your Owner s Manual Supplement for a list of features on your machine Accessories are available from your Polaris dealer 1 Reverse Indicator Light 2 Electronic Fuel Gauge 3 Temperature Light 4 Electric Shock Absorber Gauge 38 FEATURES AND CONTROLS Features 9 CO SVON SI Oe tort Hood Headlight Windshield Handlebar Seat Storage Rear Taillights Backrest Tunnel Extension 10 Passenger Hand Hold Strap 11 Track 12 13 14 15 16 17 18 19 20 21 Suspension Nosepan Trailing Arm Skis Front Bumper Console Rear Bumper Passenger Hand Hold Lifting Hand Hold Snow Flap 39 FEATURES AND CONTROLS Features Hood Headlight Windshield Handlebar Seat Storage Rear Taillights Backrest 9 Tunnel Extension 10 Passenger Hand Hold Strap 11 Track OO SV Oy UB Doe 40 Suspension Nosepan Trailing Arm Skis Front Bumper Console Rear Bumper Passenger Hand Hold Lifting Hand Hold Snow Flap Hood Closures Edge Models Onl
49. changers 3 Remove the bleed screw from the water outlet manifold and or the thermostat housing Allow the coolant to bleed through the system until it runs out the bleed holes Reinstall the bleed screw into the manifold 4 Fill the recovery tank to the maximum indicated mark 5 Start the engine and run at a fast idle for two to three minutes Occasionally loosen the bleed screw to purge any trapped air in the system 6 Shut offthe engine and check the recovery tank level Fill as required 7 Feel the heat exchangers under the running boards If the system is bled properly they ll be warm to the touch If they re not repeat step 5 Lift the front of the machine slightly to assist in the bleeding 8 Replace the pressure cap and carefully lower the front end of the machine 122 MAINTENANCE General Maintenance EDGE RMKs 1 Remove pressure cap and fill tank to maximum recommended mark 2 Elevate the front of the machine 3 Start the engine and run at a fast idle for two to three minutes Air bubbles should come to the surface of the coolant tank Run the machine until air bubbles no longer appear 4 Shut off the engine and feel for warmth along the tunnel If the machine is bled properly the deicer gripper coolant extrusions will be warm 5 If needed fill coolant to maximum recommended mark 6 Replace the pressure cap and carefully lower the front end of the machine Drive Chain Tension To obtain correct chain tens
50. chemicals known to cause cancer birth defects or other reproductive harm OPERATION Fuel The fuel used in your Polaris engine is as important to engine life and performance as the lubricant used Most Polaris engines are designed to run on 87 octane non oxygenated or 89 octane oxygenated pump gasoline There s a great deal of variability in the quality of the 87 octane gasoline available across the country so we encourage the use of premium fuel when possible NOTE Some Polaris snowmobiles require premium gasoline Check your Owner s Manual Supplement to determine what type of fuel your machine requires Premium Fuel Switch Some Polaris snowmobiles are Premium Fuel Setting equipped with a key function to adjust the timing on the machine as you change fuels It s very important to the life of your engine that you use this feature When using fuels with a pump posted octane rating of 91 or higher turn the key switch to ON PREM When the engine is started a yellow Premium Fuel light illuminates on the instrument panel When the key is in this position the fuel must be a minimum of 91 octane Regular Fuel Setting Most high performance machines require the use of premium fuels Substituting other fuels may cause engine damage ON REG CAUTION Using lower than the recommended octane fuels or operating with obstructed fuel systems will lead to costly engine damage 81 OPERATION Fue
51. decreases softening the ride The factory setting is in the softest position screw all the way out counterclockwise If bottoming occurs the Indy Select feature should be used to achieve the desired ride effect One half turn will affect the ride considerably There are about three turns of adjustment available If experimenting with this adjustment feature turn the screw only 1 4 turn at a time And always adjust both shocks equally 48 THE PERFECT FIT Rear Suspension Adjustments Rear Suspensions Polaris has six different rear suspension packages each designed and set up to deliver a soft ride under average riding conditions Rider weight riding style trail conditions and vehicle speed all affect suspension action Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions However all suspension designs and adjustments involve a compromise or trade off For example a suspension set up for snow cross racing would provide a very stiff ride on the trail A suspension set up for trail riding would bottom out harshly on a snow cross course A decal outlining rear suspension set up options is located either under the hood or on the clutch cover It provides a guideline for initial suspension set up Additional adjustments can be made from this point Make adjustments to one area at a time so you can evaluate the change For further assistance see your dea
52. designed to stop the engine whenever all pressure is removed from the throttle lever and the throttle cable or valves do not return to the normal closed position AWARNING If the throttle safety switch does not shut off the engine during a carburetor throttle system malfunction immediately push down the engine stop switch Do not start the engine until the malfunction has been corrected by your dealer 86 OPERATION Throttle Lever AWARNING An improperly functioning throttle lever may cause erratic machine behavior and loss of control which could result in serious injury or death If the throttle lever does not work properly DO NOT start the engine If the engine stops abruptly when the throttle lever is released 1 Turn the ignition switch to OFF 2 Visually inspect the throttle cable and carburetor s to determine what caused the safety switch to activate 3 Test the throttle lever by compressing and releasing it several times The lever and cable must return to the idle position quickly and completely 4 Ifthe throttle lever operates properly turn the ignition switch on and go through normal starting procedures 5 If the engine doesn t start take the snowmobile to an authorized Polaris dealer for service Excessive free play in the throttle cable may cause the safety switch to activate preventing the engine from starting If this occurs return the machine to an authorized Polaris dealer for s
53. djustments If the spring preload is at its maximum and you want more adjustment Remove the existing spring and install the next highest rate spring or Change the shock valving on Fox and RYDE FX shocks or Increase compression damping on Indy Select shocks PE 52 See your dealer for details NOTE Some models do not have shocks with thread adjustable spring preload Changing Shock Valving If you find that spring preload adjustment alone is not sufficient changing the valving of your Fox or RYDE FX shocks may give you the ride adjustment you want The purpose of shock valving is to control the stiffness of the shock s compression AWARNING Changing shock valving on Fox and RYDE FX shocks requires special tools and a sound knowledge of mechanical theory tool use and shop procedures to perform the work safely and correctly Shocks contain high pressure nitrogen gas Use extreme caution when handling high pressure service equipment This work should be performed by a Polaris dealer 47 THE PERFECT FIT Front Suspension Adjustments Indy Select IFS Shock Some snowmobiles are equipped with Indy Select IFS shocks which allow you to make adjustments to the compression valving of the front shocks by turning adjustment screws A located near the base of the shocks By turning the screw clockwise the compression of the shock increases stiffening the ride By turning counterclockwise the compression
54. dlights and reducing your speed Your snowmobile is equipped with a high output headlamp system that may cause discomfort to operators of oncoming vehicles when on high beam i When traveling in a group of snowmobiles don t tailgate follow too closely Allow ample stopping distances and keep track of those following you Drive defensively to avoid accidents i Don t tempt anyone to steal your snowmobile or ride it without permission Remove the key from the ignition 25 SAFETY Operator Safety Windchill Temperature Charts The following information is provided to help you determine when temperatures become dangerous for riding WIND CHILL CHART F Estimated Wind Speed Actual Thermometer Reading F in MPH 50 40 30 20 10 O 10 20 30 40 50 60 Equivalent Temperature F Calm 50 40 30 20 10 O 10 20 30 40 50 60 5 48 37 27 16 6 5 15 26 36 47 57 68 10 40 28 16 4 9 21 33 46 58 70 83 95 15 36 22 9 5 18 36 45 58 72 85 99 11 2 20 32 18 4 10 25 39 53 67 82 96 11 12 0 4 25 30 16 O 15 29 44 59 74 88 10 11 13 4 8 3 30 28 13 2 18 33 48 63 79 94 10 12 14 9 5 0 35 27 11 4 20 35 49 67 82 98 11 12 14 3 9 5 40 26
55. e the rider drop down hard on the seat and bounce up and down several times collapsing the rear suspension With the rider seated measure the distance between the ground and the rear bumper at the exact location used for measurement X This is measurement Y To determine sag commonly referred to as ride in subtract measurement Y from X Sag X Y Adjust sag by rotating the torsion spring preload cams located on the rear torque arm Use the illustration or the decal found under the hood for reference The ideal amount of sag for the EDGE RMK rear suspension is four inches X Y 4 If the rear suspension rides in less than three inches or more than five inches with the torsion spring preload cams at their maximum range of adjustment optional torsion springs softer or stiffer respectively may be required This is only an initial setup and final spring preload may vary based on rider preference and riding conditions 50 THE PERFECT FIT Rear Suspension Adjustments Rear Spring Tension To adjust rear torsion spring tension rotate the three position cam using the engine spark plug tool Different rate torsion springs are available if a firmer ride is desired Contact your dealer for more information The following information is provided only as a guideline to be used for initial suspension set up Your set up may vary based on your desired riding style 1 Turn screw clockwise to stiffen compres
56. eTrak models can also be warmed up with the transmission in neutral and the brake engaged This will allow the engine to warm without engaging the drive system NOTE Don t leave the machine in this position for more than five minutes Engine RPM should be at idle before shifting the transmis sion Starting a Warm Engine 1 Turn key to ON 2 Pull kill switch shut off switch up to RUN 3 Grasp starter handle and pull slowly until recoil engages then pull to start If the engine does not start on the first pull slightly depress the throttle with your left hand no more than 1 4 open and pull the rope with your right hand When the engine starts immediately release the throttle CHOKE TOGGLE POSITIONS 75 OPERATION Engine Break In No single action on your part is as important to long trouble free machine life as proper break in of a new or rebuilt engine Premix the first tank of gasoline with one pint of Polaris injection oil for each five gallons of fuel This in addition to the lubrication supplied by the injection system will assure proper engine break in CAUTION Never mix brands of two cycle oil Serious chemical reactions can cause injection system blockage resulting in serious engine damage and the voiding of engine warranty The only oil recommended for this system is Polaris injection oil This oil has been specially formulated for all temperatures and has extreme cold flow character
57. ecrease torsion spring preload adjustments Remove rear track shock spring Decrease front track shock compression damping by turning screw counter clockwise Adjust front track shock spring to less preload Machine darts from Make sure skis are aligned properly side to side Make sure spindles and all steering components are free turning Make sure skags are straight on skis Ensure use of E Z Steer skags Shift FRSS to highest position Front end pushes Check for worn skags Check for binding suspension shafts and grease all pivot points Increase front IFS preload Change FRSS to low setting or move to forwardmost hole Steering is heavy Check ski alignment Check skags and skis for damage Change FRSS to high setting Decrease IFS spring preload Make sure spindles and all suspension components are free turning Setting up for deep Rotate FRSS to lowest setting depending upon rider preference snow operation Decrease preload on front track spring Tighten limiter strap one hole Move FRSS to forwardmost hole Tighten limiter strap one hole 158 TROUBLESHOOTING Suspension Troubleshooting X 12 133 Solution perform only one change at a time Rear suspension Check to be sure FRSS block is in highest position bottoms too easily Adjust torsion spring blocks to highest position Adjust coil over spring on front track shock to increase preload Replace front track spring with overload kit 2871439 Incre
58. ect the negative black cable first and reinstall the negative cable last to avoid the possibility of explosion Battery electrolyte contains acid Avoid skin contact with electrolyte as severe burns may result 1 Place the battery in its holder Attach the hold down strap 2 Install the battery vent line It must be free from obstructions and securely installed Route the vent line properly to prevent kinks and to allow for proper drainage 3 Connect and tighten the red positive cable first Connect and tighten the black negative cable last 5 Verify that cables and vent hose are properly routed P 155 156 NOTES SECTION 8 TROUBLESHOOTING Suspension Troubleshooting 158 162 Belt Troubleshooting 0 00000 163 Engine Troubleshooting 164 166 Section 8 is a quick reference guide to solving problems 157 TROUBLESHOOTING Suspension Troubleshooting X 12 Solution perform only one change at a time Rear suspension Check to be sure FRSS block is in highest position bottoms too easily Adjust torsion spring blocks to highest position Adjust coil over spring on front track shock to increase preload Change torsion springs to 421 diameter on 121 models only Change to next heavier coil spring Increase front track shock compression damping by turning screw clockwise Rides too stiff in Check for binding suspension shafts and grease all pivot points rear D
59. ed surfaces Be sure that corrosive salt and acids are removed from surfaces before beginning preservation with waxes and rust inhibitors grease oil or paint The machine should be stored in a dry garage or shed out of direct sunlight and covered with a fabric snowmobile cover Plastic tarp may cause condensation to form and damage snowmobile components Controls and Linkage All bushings spindle shafts and tie rod ends should receive a light coat of oil or grease Throttle controls and cables should be lubricated with Polaris cable lubricant PN 2870510 Force a small amount of lubricant down the cable 149 MAINTENANCE Extended Storage Bearings Grease jackshaft and drive shaft clutch side bearings with a high quality bearing grease to prevent corrosion Clutch and Drive System Remove drive belt and store in cool dry location Lubricate sheave faces of drive and driven clutches with a light coat of oil or Polaris Cable Lubricant PN 2870510 Do not lubricate clutch components except driven clutch shaft bushing as outlined in Master Repair Manual See your dealer Engine and Carburetor Protection Proper preparation of the engine and fuel system is vital to the prevention of rust and corrosion on precision engine parts during storage Whenever the machine is stored for a period of more than 60 days the engine must be fogged Polaris PN 2870791 Follow the engine fogging instructions provided on the can Always add a
60. emergency start strap is provided in the kit To use the emergency start strap 1 Open the clutch guard 2 Push on the inner sheave of the clutch and rotate clockwise 7 ZN slightly to relieve belt Ly tension f as 3 Starting at one of the tower struts wind the strap counterclockwise around the clutch as shown 4 Pull the strap using a sharp crisp pull so the strap comes free of the clutch 89 OPERATION Reverse Operation Mechanical AWARNING Misuse of reverse can result in serious injury or death This snowmobile is capable of high speeds in reverse Reverse operation may be dangerous even at moderate speeds Steering control becomes difficult in reverse Make sure the shift lever is shifted completely into forward or reverse position Some models are equipped with a reverse indicator light that will help you make that determination Do not force the shift lever into reverse if resistance is felt The gears may not always be aligned for shifting into reverse and forcing the lever may cause damage If resistance is felt gently apply the throttle to move the gears to a different position and try to shift again The transmission may not always be in the gear indicated by the shift lever Apply the throttle slowly until you re sure which gear is engaged Sometimes the drive belt will drag in the drive clutch causing slight tension in the transmission and making it hard to shift Shutting the
61. emoving the Side Bulbs 1 Disconnect terminal from back of bulb 2 Turn bulb assembly 1 4 turn to right and withdraw from housing Installing the Side Bulbs 1 Hold bulb assembly by plastic base and plug into wire terminal 2 Insert bulb assembly into housing 3 Turn bulb assembly 1 4 turn to left to secure in housing 4 Verify headlight operation Wrap Around Taillight Bulb Replacement 1 Remove phillips screws from the taillight lens A 2 Working from front to back carefully pry lens away from seal and remove lens 3 Pull bulb s B straight out from socket and insert new bulb s 4 Reinstall lens 131 MAINTENANCE General Maintenance Periodically check the condition and tension of the drive belt and always carry a spare belt For improved drive away during extremely cold temperatures remove the belt and warm it to room temperature Reinstall it before starting the snowmobile Standard Belt Removal 1 Be sure the key switch is off and the engine has come to a complete stop Remove the retaining pin and open the clutch guard 2 Apply brake or lock parking brake if equipped 3 Grasp the belt firmly midway between the clutches and pull upward and rearward Remove the belt Electronic Reverse Belt Removal 1 Remove ONE of the three belt tension adjuster bolts A and store it in a safe place 2 Locate the 1 1 2 bolt from the tool kit and install it in the empty tensioner hole As this bolt
62. enter BDC the lowest position in the cylinder On twin cylinder models the opposite piston will be up 5 Pour approximately two ounces of Polaris injector oil into the spark plug hole 6 Wait one to two minutes and perform steps 3 to 5 on remaining cylinders 7 Replace the spark plugs and lower the machine to the floor Electrical Connections Separate electrical connector blocks and clean corrosive build up from connectors Lubricate or pack connector blocks with dielectric grease PN 2871044 and re connect Replace worn or frayed electrical wire and connectors Be sure wiring harness is properly secured away from sharp edges steering linkage moving parts and hot exhaust parts Battery Always prepare and maintain the battery as outlined on page 153 151 MAINTENANCE Extended Storage Track and Suspension Moderate track tension should be maintained during summer storage The machine should be supported off the ground to allow the track to hang freely See illustration Transporting the Snowmobile Whenever the snowmobile is transported 1 Turn the fuel valve clockwise to OFF 1 to shut off the fuel supply 1 Turn the valve counter clockwise to ON to turn the fuel supply on 2 NOTE The fuel valve is located to the right of the fuel pump or behind the airbox between the fuel pump and fuel tank 2 Be sure the fuel cap and oil cap are installed correctly 3 Always tie the snowmobile
63. er function of a tow hitch must be understood before attempting its use AWARNING DO NOT tow toboggans sleds saucers or any type of vehicle with a rope No braking power can be applied to an object being towed with a rope Only a stiff metal pole connecting the towed object and tow hitch on the snowmobile should be used If passengers are to be towed on a toboggan or sled make sure the pole is at least four feet 1 2 meters long to prevent any possibility of contact between the vehicle track and a person riding in the towed object Braking distances increase when towing loads Slow down to maintain control Tip over can result in serious injury or death If the snowmobile is inoperable and must be towed and if it isn t possible to use a rigid tow bar attach the tow rope to the ski spindles not the ski loops to prevent damage to the steering components Have a rider on the snowmobile to operate the brake and steering when necessary CAUTION To prevent serious damage to the engine and drive system always remove the drive belt from a disabled snowmobile before towing 93 NOTES SECTION 7 MAINTENANCE Polaris Recommended Maintenance Program 0 20e08 96 Maintenance Charts 0000 97 98 Maintenance Log 20e00 99 100 Lubrication ics2055 ceseleet ethno dex 101 110 General Maintenance 111 139 Track Maintenance 5 140 143 S
64. er your weight shifting ability This could affect your ability to control this rider active vehicle in certain extreme driving situations Be Prepared for the Unexpected For your safety always ride in a group of other snowmobilers Always tell someone where you re going and how long you expect to be gone If it isn t possible to ride with others and you must travel into remote areas always carry survival equipment that s appropriate to the conditions you may encounter Such equipment may include but is not limited to extra clothing a sleeping bag a flashlight food and water a signaling mirror a means of building a fire and a two way radio or cellular telephone 15 SAFETY Operator Safety Do Not Overload Cargo Carrier Too much weight on the rear of the machine may reduce your ability to steer Do not exceed carrier and rack weight limits and do not allow a passenger to sit on the seat back or the cargo carrier AWARNING Control becomes more difficult with two people on board More space is required to make turns and longer distances are needed for stopping Make sure the passenger remains seated behind the driver facing forward with both feet placed firmly on the running boards Slow down and avoid jumping your snowmobile Always Wear Clothing Designed for Snowmobiling AWARNING Loose clothing or long scarves may easily become entangled in moving parts and cause serious personal injury
65. ervice If an emergency exists and it s necessary to start the engine the throttle safety switch and engine stop switch may be disconnected from the wire harness When these switches are disconnected the ignition key switch must be used to shut off the engine DO NOT continue to operate the machine with the throttle safety switch disconnected Return the machine to an authorized Polaris dealer for service as soon as possible 87 OPERATION Emergency Stopping And Starting Stopping The following chart lists methods for stopping the snowmobile in the event of an emergency Refer to page 86 for more information about the engine stop switch and throttle safety switch SYSTEM WHAT IT DOES THROTTLE CONDITION AWARNING Excessive or repetitive use of brakes for high speed stops will cause an overheated brake system This overheated condition could cause sudden loss of brakes and or fire resulting in serious injury or death When traveling on long downhill stretches pump the brakes Riding the brakes may cause the brake system to overheat resulting in brake failure 88 OPERATION Emergency Stopping And Starting Starting AWARNING To prevent serious injury DO NOT wind the start strap around your hand Keep all bystanders away from the snowmobile when using the emergency starting procedure Your machine is equipped with a tool kit containing essential tools for emergency use If the recoil starter system fails an
66. es and all steering components are free turning Make sure skags are straight on skis Install E Z Steer skags Check for worn skags Check for binding suspension shafts and grease all pivot points Increase IFS preload Shorten limiter strap on front torque arm Increase torsion spring preload Make sure spindles and all steering components are free turning Check ski alignment Check skags and skis for damage Decrease IFS preload Change front track spring to next higher rate Shorten limiter strap on front torque arm Increase torsion spring preload Move rear torque arm assembly and associated parts to rear ward mounting position Lengthen limiter strap on front torque arm Decrease torsion spring preload Move rear torque arm assembly and associated parts to forward mounting position TROUBLESHOOTING Belt Troubleshooting Belt Wear Burn Belt Wear Burn Diagnosis causes Solutions Driving at low RPM Drive at higher RPMs Gear the machine down Check belt deflection Insufficient warm up Warm the engine at least five minutes Take the drive belt off the machine in extremely cold weather and warm it up Break machine loose from the snow Towing at low RPM Do not tow in deep snow Use fast aggressive throttle to engage clutch Riding with high RPM Lower the gear ratio Remove windage plates from the and slow speed 8000 clutch Reduce RPM Avoid riding in high ambient RPM 10 MPH temperatures
67. fuel conditioner stabilizer or Premium Carbon Clean PN 2871326 to the fuel tank Follow the instructions on the can running the engine for five minutes to get additives through the entire fuel system Top off with fresh fuel HINT For easier starting after extended storage add lubricant to the fuel in the tank at a 40 1 ratio and run the engine for three to five minutes before storage This will lubricate the fuel pump diaphragm to keep it flexible and help prevent loss of prime If stabilizer is not used drain the carburetors by removing the water trap drain plugs see page 116 Catch fuel in a container or shop cloth Reinstall plugs securely Observe all fire safety rules when draining carburetors See gasoline warnings on page 80 Jet restriction caused by improper storage can cause lean conditions and very poor slow speed driving quality 150 MAINTENANCE Extended Storage Engine and Carburetor Protection Using a fuel stabilizer and topping off the fuel tank eliminates the need to drain the fuel system If you prefer to drain the fuel tank use the following procedure 1 Transfer unused fuel from the fuel tank to an approved fuel container using a siphon pump Do not re use fuel after storage 2 Securely support the front of the snowmobile with a jack stand so the machine is elevated and the engine is tilted rearward 3 Remove the spark plug s 4 Rotate the engine slowly watching the piston until it s at bottom dead c
68. g Cargo load affects machine steering and response Never allow person s to use carrier as a means of hand support skiing skidding or dragging Severe injury may result due to track entanglement falling off or loss of steering control if warnings are not followed 29 SAFETY Safety Decals And Locations Passenger Warning 5 Some snowmobiles are designed for the operator only while others are designed for the operator and one passenger A warning decal on either the console or the hood of your machine indicates whether it s designed for the operator only 1 Up or the operator and a passenger 2 Up For more information on operating capacities see page 24 Decal text found on 1 Up Models This vehicle is designed for operator only NO PASSENGER Decal text found on 2 Up Models This vehicle is designed for operator and ONE passenger only 30 SAFETY Safety Decals And Locations Standard Reverse Warning Decal 6 Some Polaris snowmobiles are equipped with reverse These models will have a reverse warning decal s above the instrument housing The decals shown here are provided for identification and location purposes only The text found on the decals is VEHICLE CAPABLE OF EXCESSIVE REVERSE SPEED Reverse operation may be dangerous even at low speeds Steering control becomes difficult in reverse Misuse of reverse may result in injury Avoid turning at shar
69. g board area of snow then step down the snow in front of the machine so that when the throttle is opened the snowmobile will be able to climb up and over You may then mount the machine and continue riding ACAUTION When operating on icy surfaces or hard packed snow avoid overheating the slide rail and track Lack of lubrication and cooling will cause overheating of the slide rail and track resulting in premature wear and failure If frequently operating in low cooling conditions see your dealer for an optional wheel kit that will reduce the wear from overheating 23 SAFETY Operator Safety Your Polaris snowmobile is a well engineered and well constructed recreational vehicle Follow the recommended maintenance program outlined beginning on page 96 of this manual to ensure that all critical components on the snowmobile are thoroughly inspected by your dealer at specific mileage intervals Driving 1 Up Some Polaris snowmobiles are designed for a single rider only A decal on the console of these models indicates single rider operation See page 30 for decal location Driving 2 Up Some Polaris snowmobiles are designed for two riders A decal on the hood of these models indicates that the vehicle is designed for one operator and one passenger only See page 30 for decal location Machines designed for two riders should never be operated with more than two people on board When traveling with a passenger it s the driver
70. h safe service or adjustment procedures and the use of tools or if you don t feel comfortable performing these tasks yourself contact an authorized Polaris dealer for service 96 MAINTENANCE Maintenance Chart The following chart is a guide based on average riding conditions You may need to increase frequency based on riding conditions When inspection reveals the need for replacement parts always use genuine Polaris parts available from your Polaris dealer Weekly or 150 M 1000 M 2000 M See before 240 km 1600 km 3200 km Page long trip Check brake operation and Daily 66 124 adjustment a a ee Presteterseep pay 7 restive stesyswteh Baily __ a8 Pthotteeveroperaion Daily __ 68 80 ESE a Wd taillight brakelight check park brake tacion pay _ _ FSecuehood aly _ Gheckuackaigmen __ e Scoingarmmandiewodents x _ _ _ FTionte cable condiion E _ Come e o e o C E _ _ CA x __ _ creck chsneaseoirever x _ _ o check gsurenseotevet __x _ _ 1 creck drive chamens x _ _ 23 C E S E E E EEA Check and tighten loose suspension mounting bolts Tighten ski saddle and spindle bolts Check front limiter strap condition tighten bolts Check ski skags replace when worn to half original diameter Check Hi fax thickness replace 149 when worn Dealer Tiemen rear dlerwheetbors x _ e mL XTX Eal Eal Eai Eal Eal Eai
71. h speed may cause fading or unexpected loss of braking ability Oil injection system Unmixed fuel only Check oil level when refueling If you do not have the Owner s Manual for this vehicle call 1 800 324 3764 to have one provided at no charge SECTION 3 FEATURES AND CONTROLS Location of Controls 36 38 Featur S ea cisterns sccew a cahhae ye ene 39 41 Section 3 illustrates the locations of your snowmobile s controls and features 35 FEATURES AND CONTROLS Location of Controls NOTE Your machine may not look exactly like the illustration but these controls are found in the same general area on all machines 1 Fuel Filler Cap some models have a fuel gauge in the cap 2 Ignition Switch 3 Brake Lever 4 Speedometer may include indicator warning lights 5 Tachometer may include indicator warning lights 6 Engine Stop Switch Push Pull Operation found on page 86 7 Throttle Control 8 Hood Hold Down Straps 9 Recoil Starter Handle 10 Choke Control 36 FEATURES AND CONTROLS Location of Controls NOTE Some Polaris snowmobiles are equipped with special features Controls for these features are illus trated on this page Not all models come with these features Refer to your Owner s Manual Supplement for a list of features on your machine Accessories are available from your Polaris dealer 1 Headlight Dimmer Switch 2 Position Park Brake Handle
72. he brake reservoir If the fluid is sufficient the sight glass will be black If the sight glass is any color other than black add brake fluid Use only Polaris DOT 3 high temperature brake fluid PN 2870990 Polaris brake fluid is sold in 12 oz bottles 126 MAINTENANCE General Maintenance Bleeding the Hydraulic Brake System Air in the hydraulic brake system will cause a springy or spongy brake lever action Bleeding is necessary to remove air from the system CAUTION Brake fluid will damage decals paint and some plastics Wipe up spills immediately 1 Remove brake master cylinder reservoir cover and gasket 2 Fill the master cylinder reservoir to between the MIN and MAX marks or 1 4 5 16 6 8 cm below the lip of the reservoir opening Reinstall the gasket and cover 3 Slip arubber tube over the ball of the bleeder valve and direct the flow of fluid into an approved container 4 Squeeze brake lever a full stroke Then unscrew bleeder valve 3 4 of a turn to release air 5 Close bleeder valve and release brake lever 6 Repeat steps 4 and 5 until fluid flows from the bleeder valve in a solid stream free of air bubbles AWARNING Do not overfill the master cylinder Fluid expansion may cause brakes to lock resulting in serious injury or death 7 After bleeding is complete refill the reservoir to the proper level See Replenishing Brake Fluid on page 126 8 Reinstall the gasket and cover During the bleedi
73. heck the oil level place the machine on a level surface The oil level should be between the safe marks on the dipstick A See your Polaris dealer for the recommended oil for your machine Do not overfill NOTE Clean the magnetic plug B every 500 miles 800 km and whenev er checking or changing lubricant CAUTION Do not mix lubricants or use other types of lubricant This could result in excessive wear to chain sprockets and bearings 110 MAINTENANCE General Maintenance Intake Filter The intake foam filter limits snow ingestion into the intake system When operating in loose powder snow check the top of the foam filter periodically to remove any accumulation of snow CAUTION Operating the snowmobile with the intake filters removed may cause carburetor icing The result will be poor fuel economy or carburetor malfunction NOTE These illustrations are general representations Your model may differ 1 Intake Foam Filter 2 Air Intake box 3 Dash Cowl 111 MAINTENANCE General Maintenance Under Hood Air Intake System The under hood air intake system on Indy 340 s should normally be left open However for maximum performance in temperatures above 35 F 2 C and in loose snow the door should be closed and latched A Pull the strap out and up to latch the door and reverse the procedure to open it Spark Plug Selection
74. his decal will depend on the model you own The decals shown here are offered for identification purposes only The text of the decal is printed on the next page 32 SAFETY Safety Decals And Locations Operation Warning Decal Text Read and understand warnings and the Owner s Manual before operation Severe injury or death can result from not heeding the warnings Never consume alcohol or drugs before or while operating this ve hicle Night riding limited visibility or excessive speeds may cause over driving of headlights resulting in insufficient time to react to terrain changes or avoid unexpected obstacles This vehicle is capable of high speeds Buried objects or uneven terrain can cause loss of control Exercise extreme caution when operating in unfamiliar terrain This vehicle is designed for adult use only The vehicle size speed capabilities and control requirement prohibit operation by children Operating this vehicle with a passenger On approved models only reduces your ability to control the vehicle due to the added weight and change in weight distribution Reduce vehicle speeds and al a a space for maneuvering since steering control may be reduced Always wear an approved helmet eye protection and adequate clothing while operating this vehicle The Auxiliary Shut Off Switch is the primary means of stopping this vehicle in case of an emergency and is located on the top of the throttle control
75. ication added to the fuel and oil injection systems Use only Polaris products We are continuously testing lubricants and provide the highest performance products available for your engine Please refer to the table below to determine the preferred and acceptable oils for use in your engine Never mix other brands of oil They may be incompatible and the result could be sludge formation filter blockage and reduced cold weather flow rates All Polaris oils are compatible with each other Premium Premium VES 2 Cycle Gold 2 Cycle Fan Cooke NA Liquid Cooled NA 77 OPERATION Track Warm Up AWARNING A loose track or flying debris could cause serious personal injury or death Stand clear of the front of the machine and the moving track Never hold the snowmobile up or stand behind it while performing this procedure Do not use too much throttle during warm up or when track is free hanging Be sure the rear support is stable NOTE The outside temperature will determine the amount of track warm up required With the snowmobile securely supported by the rear bumper and the track approximately 4 10 cm off the ground follow these steps to ensure proper warm up of the engine drive train and track Start the engine and allow it to warm up two to three minutes 2 Depress the throttle abruptly and allow the track to rotate several revolutions 3 Release the throttle apply the brakes shut off the engine and lowe
76. idler shaft Edge RMK 136 10 lbs 4 54 kg 16 ahead of rear 3 8 1 2 1 1 3 cm idler shaft Edge RMK 144 10 lbs 4 54 kg 16 ahead of rear 1 2 3 4 1 9 idler shaft Edge RMK 151 10 lbs 4 54 kg 16 ahead of rear 1 2 3 4 1 9 idler shaft Edge RMK 156 10 lbs 4 54 kg 16 ahead of rear 1 2 3 4 1 9 idler shaft Edge 10 lbs 4 54 kg 16 ahead of rear 3 8 1 2 1 1 3 cm idler shaft Refer to your M 10 Owner s Manual Supplement 140 MAINTENANCE Track Maintenance AWARNING Moving parts can cut and crush When performing the checks and adjustments recommended on the following pages stay clear of all moving parts Never perform track measurement or adjustments with engine running Track Tension Track adjustment is critical for proper handling Always maintain correct tension and alignment Tension adjustments should be made only after the track is warmed up and limber 1 2 3 4 Turn the machine off Lift the rear of the machine and safely support it off the ground Place the recommended weight or downward pressure on the track at the specified distance see chart on page 140 ahead of the center of the rear idler wheel NOTE Measure at the point where the weight is hanging Check for specified slack between the wear surface of the track clip and the plastic Hi fax C If the track needs adjustment 3 6 Loosen rear idler shaft bolt D Loosen l
77. ile courtesy and enroll them in driver s training and safety courses sponsored by local or state organizations 18 SAFETY Operator Safety Ice and Snow Build up AWARNING Ice and snow build up may interfere with the steering of your machine resulting in serious injury or death Keep the underhood area free of snow and ice Before driving manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering If difficulty is encountered check for ice and snow build up that may be obstructing the steering linkage Snow screens and bib kits are available through your dealer to help reduce snow and ice build up Operation on Hard Packed Snow or Slippery Surfaces AWARNING Driving on ice or hard packed snow reduces steering and braking control which may result in serious injury or death Slow down and use caution Excessive shifting of operator body weight when turning on hard packed snow or ice may lead to loss of vehicle control and result in serious injury or death Slow down to maintain control under these conditions It s dangerous to drive on ice or other slippery surfaces If it s unavoidable use extreme caution and operate at speeds no faster than a walk Never attempt an abrupt change of direction The chance of spin out increases under these conditions 19 SAFETY Operator Safety Driving in Hilly Terrain AWARNING Climbing a hill or c
78. ing Make sure skags are straight on skis Install E Z Steer skags Check for worn skags Check for binding suspension shafts and grease all pivot points Verify sag dimension refer to set up decal or page 50 Adjust torsion spring blocks Increase torsion spring diameter see your dealer Increase IFS preload by turning the spring collar to the right Move limiter strap on front torque arm to high position Verify sag dimension refer to set up decal or page 50 Adjust torsion spring blocks Install optional torsion springs see your dealer Decrease IFS preload 161 TROUBLESHOOTING Suspension Troubleshooting XTRA LITE Solution perform only one change at a time Rear suspension bottoms too easily Rides too stiff in rear Machine darts from side to side Front end pushes Steering is heavy Too much weight transfer when climbing Too little weight transfer when climbing 162 Adjust torsion spring block to next higher position Increase rear shock compression damping by turning screw clockwise Change torsion springs to next higher rate springs Change front track spring to next higher rate Check for binding suspension shafts and grease all pivot points Decrease torsion spring preload adjustments Decrease rear shock compression damping by turning screw counter clockwise Change torsion springs to next lower rate springs Make sure skis are aligned properly Make sure spindl
79. ing Turn the knob in or out as needed for proper aim 129 MAINTENANCE General Maintenance NOTE Do not touch a halogen bulb with bare fingers Oil from skin leaves a residue causing a hot spot that will shorten the life of the lamp Removing Halogen Bulbs High Low Beam 1 Pinch the ends of the spring 1 together and lift until it releases from the spring retainer 2 Lift spring carefully around wire harness 2 and flip to outside of housing 3 With the wire harness attached to the bulb 3 withdraw bulb from housing 4 Grasp bulb by metal base and carefully separate bulb from harness Installing the Bulb 1 Hold bulb by metal base and install into wire harness 2 Insert bulb into housing 3 Carefully flip spring back into housing placing it around wire harness 4 Squeeze spring together until it is over the spring retainer and release 5 Verify headlight aim Removing Halogen Bulbs High Beam 1 Remove the wire harness 4 2 Gasp the bulb 5 firmly and twist it 1 2 turn counterclockwise 3 Remove the bulb from housing and replace with new bulb 4 Place the bulb and housing back inside the hole and turn the housing 1 2 turn clockwise to lock into place 5 Reinstall the wire harness to the housing 130 MAINTENANCE General Maintenance NOTE Do not touch a halogen bulb with bare fingers Oil from skin leaves a residue causing a hot spot which will shorten the life of the lamp R
80. ing the engine always refer to all safety warnings pertaining to snowmobile operation Never start your snowmobile without checking all components to be sure of proper operation See Check Before Starting the Engine beginning on page 66 Starting a Cold Engine Manual Start Do not depress the throttle until the engine starts 1 Turn key to ON 2 Pull kill switch shut off switch up to RUN 3 Flip choke toggle to FULL ON 4 Grasp starter handle and pull slowly until recoil engages then pull to Start CAUTION Don t pull the starter rope to full extended position or allow it to snap back into the housing Damage may result 5 After the engine starts flip the choke toggle to the OFF position If the engine slows or wants to stop use intermittent choking to the HALF ON position 4 amp CAUTION To avoid personal injury and or engine damage do not operate the electric starter or pull rope starter while the engine is running 74 OPERATION Starting Your Engine Starting a Cold Engine Electric Start Do not depress the throttle until the engine starts 1 Flip choke toggle to FULL ON 2 Pull kill switch shut off switch up to RUN 3 Turn key to START and crank engine 4 After the engine starts release the key to ON and flip the choke toggle to OFF If the engine slows or wants to stop use intermittent choking to HALF ON 5 Wid
81. ion 1 Rotate the driven clutch counterclockwise to move all chain slack to the tensioner side Lock the brake lever lock or have an assistant hold the brake lever firmly Loosen the adjuster bolt jam nut A Finger tighten the adjuster bolt B until it can no longer be adjusted by hand then back off 1 4 turn Tighten the jam nut while holding the adjuster bolt The chain is now tensioned Release the brake lever lock 123 MAINTENANCE General Maintenance Hydraulic Brake Inspection Frequently inspect the brake lever reserve Firmly depress the brake lever and measure the clearance between the lever and handlebar grip This distance called brake lever reserve A should be no less than 1 2 1 3 cm Brake pads must be replaced when the brake pad material becomes thinner than the backing plate approximately 1 16 A kit is available for replacing brake pads See your dealer AWARNING Properly functioning brakes are vital to your safety Be sure the brake pads do not drag on disc and that brake lever travel is not excessive Brake pads must be replaced when the brake pad material becomes thinner than the backing plate approximately 1 16 124 MAINTENANCE General Maintenance Brake Components 1 2 3 4 5 Brake Caliper Chaincase Brake Disc Backing Plate Brake Pad M
82. ion Track 143 Inspection Water Pump Belt 115 Installing the Side Bulbs 131 Lighting Check 00 71 Liquid Cooled Models 119 Location of Controls 36 40 Log Maintenance 99 100 Low Oil Indicator Light 83 Low Oil Level 84 Lubrication 101 110 Lubrication Cables 108 Lubrication Engine 77 Maintenance 95 155 Maintenance Check List 97 98 Maintenance Inspection 99 Maintenance Log 99 100 Maintenance Program 96 Manual Start 0 74 Mechanical Brakes 68 Oca as scour erg acetate 77 83 84 Ol Filter sassinoro eee pe De ea oe 117 Oil Injection System 77 Oil Level Chaincase 109 Oil Level Gearcase WideTrak 110 OU TAG bi ie Sa RS et wots 83 Operation 0 0 73 93 Operation Warnings 16 Cargo Carrier 04 16 Clutch Guard 21 Clutches sinn ences tas 22 Cold Weather Driveaway 22 Drive Belter t rron ner er iaia 21 Driving on Ice 000 18 Driving Position 15 Hard Packed Snow 19 Intake Silencer Filter 22 Operation Skills 17 18 Powder Snow 23 Responsibility 0 25 Sidehilling
83. istics Do not operate at prolonged full throttle for the first three hours of operation Vary the throttle openings and machine speeds to reduce friction on all close fitting machined parts and allow them to break in slowly without damage Adequate snow coverage is necessary to properly break in your machine Avoid operating on ice hard packed surfaces or roads Snow will provide the lubrication and cooling your snowmobile needs for proper break in Inadequate cooling and lubrication will lead to overheating of the slide rail and track resulting in premature wear and failure Reduce speeds and frequently drive into fresh snow to allow adequate cooling and polishing of the slide rail and track surfaces Drive with extra caution during the break in period Perform regular checks on fluid levels lines and all other important areas of the machine 76 OPERATION Engine Break In Oil Injection System CAUTION Check the oil tank level often during the first tankful of fuel If the oil level doesn t go down contact your dealer immediately Always fill the oil reservoir when refueling Fuel to oil mix ratios are controlled by the oil pump and correspond to the engine s RPM and throttle valve opening Variable Exhaust System All snowmobile engines equipped with variable exhaust valves should use VES 2 Cycle Oil see chart on page 77 Lubrication The only source of engine lubrication for your engine comes from lubr
84. izure is a result of poor lubrication inadequate fuel supply bro ken parts or improper cooling Fuel may have entered crankcase while ve hicle was standing or being transported SEE YOUR DEALER to correct cause Drain plug s are located on lower crankcase for emergency draining 165 TROUBLESHOOTING Engine Troubleshooting Engine turns Faulty ignition Remove spark plug s and replace with new but fails to start plug s If engine still fails to start check for spark if no spark SEE YOUR DEALER No fuel to engine Make sure the fuel valve is ON Check tank level and fill up with correct fuel Ice in fuel line filter or pump On the stan dard Polaris carburetor the choke will not function with the throttle depressed See se cond item under Probable Cause of En gine continually backfires Flooded engine Hold throttle open crank engine several normal situation times may be necessary to change plug s caused by too much however the plug s may operate satisfactori choking ly when dried Poor engine com Running too lean a mixture too small a pression main jet will cause seizure resulting in loss of power SEE YOUR DEALER This indi cates a major engine problem that must be repaired before engine is run Engine lacks Fouled or defective Change and test operation power spark plug Fuel filter loss of Check fuel filter flow Disconnect hose and high RPM power drain about
85. justments are complete tighten locknuts and torque idler shaft bolts to 35 ft Ibs 4 8 kg m 5 Repeat steps 2 and 3 to verify proper alignment 142 MAINTENANCE Track Maintenance Track Inspection AWARNING Broken track rods are a serious hazard they can cause a rotating track to come off the machine Never operate or rotate a damaged track under power Serious personal injury or death may occur Using a hoist safely lift and support the rear of the snowmobile off the ground Rotate the track by hand to check for possible damage Carefully examine the track along the entire length of each rod bending the track and inspecting for breakage The three most common damage areas are shown in the illustration Replace the track if any rod damage is found Track Lubrication AWARNING Track failure loss of vehicle control and loss of braking ability can result from extended operation on surfaces providing marginal lubrication between Hi fax and track guide clips Examples of marginal lubrication include ice without snow cover icy trails hard packed snow and no snow conditions The slide rail requires adequate snow cover for sufficient lubrication Excessive wear indicates insufficient lubrication New Hi fax can cause faster heat build up in limited lubrication resulting in excessive wear NOTE If excessive Hi fax wear occurs due to poor snow conditions additional wheel kits are available
86. l Premium Fuel Switch If you re uncertain about the quality or octane rating of the fuel you use turn your key switch to ON REG The Premium fuel light will go out This setting will adjust the timing of your engine to run on fuels with 87 octane or higher Polaris does not recommend using fuel with lower than 87 octane Running your machine on ON REG will help protect your engine from damage caused by low octane fuels Fuel Reserve Capacity On models equipped with fuel reserve there are approximately two gallons of fuel left in the tank when the fuel gauge reads RES Fuel System Deicers If you use non oxygenated fuel Polaris recommends the regular use of isopropyl based fuel system deicer Polaris PN 2870505 Add one to two ounces per gallon 8 16 milliliters per liter of gasoline to prevent engine damage resulting from fuel system icing and lean fuel mixtures Never use deicers or additives containing methanol If you use oxygenated fuel containing ethanol additional alcohol deicers or water absorbing additives are not required and should not be used CAUTION Prolonged exposure to petroleum based products may damage paint Always protect painted surfaces when handling fuel 82 OPERATION Oil Low Oil Indicator Light The low oil indicator light standard on most models will indicate when to add oil However always check the oil level when refueling CAUTION When the low oil indicator
87. le rider position rotate the backrest cushion adjustment knobs 2 until the proper angle is reached The grab bars have five height adjustments To raise or lower the grab bar remove the grab bar adjuster knob 3 position the grab bar at the desired height and reinstall the knob Some models are also equipped with passenger handwarmers The switch 4 located under the left hand wind deflector has three settings High Off and Low To lengthen or shorten the backrest cable lift the cable until spring tension is felt and lock the jam nut 59 THE PERFECT FIT Accessories Polaris offers a wide range of accessories for your snowmobile From map light to electric start Polaris has the accessories that will help make each ride more enjoyable See your dealer for a list of accessories NOTE The accessory tether switch is available for all models Order PN 2870668 Use only Polaris parts and accessories on your Polaris snowmobile Use of unapproved parts and accessories may result in Non compliance with government industry requirements Voiding of warranty Personal injury to self or others This applies to but is not limited to the following areas brakes clutches fuel systems and exhaust systems NOTE Exhaust systems are critical safety areas that must use ap proved Polaris parts Please see your Polaris dealer for service 60 THE PERFECT FIT Accessories Traction Products Another way to tailor y
88. ler Suspension Performance Tips Rider weight usually determines the position at which the spring pre load should be set However this may vary with riding style With a little experimentation each rider can find a preferred set up These adjustments are easy to make involve very little time or ef fort and greatly affect the ride In deep snow a new Hi fax will offer improved performance over worn Hi fax It can also improve top speed When riding on ice or hard packed snow adding a set of bogie wheels to the rail may enhance the machine s performance Bogie wheel kits are available from your dealer Polaris offers track kits for improved flotation in deep snow See your dealer for assistance IMPORTANT Keep the suspension pivot points lubricated This will reduce moisture and rust build up and ensure proper function of the suspension components Grease rear suspension pivots before adjusting the rear suspension Refer to Suspension Maintenance on pages 148 149 49 THE PERFECT FIT Rear Suspension Adjustments Rear Suspension Initial Spring Preload Setting EDGE RMK Sag Method To set up the EDGE RMK rear suspension torsion spring preload measure the distance between the ground and rear bumper This is measurement X Take this measurement with no rider and with the rear suspension at full extension NOTE The rear bumper may need to be lifted upward slightly to fully extend the suspension Next hav
89. luded from coverage Electrical components are excluded from coverage The gearcase and transmission are excluded from coverage Polaris acknowledges the following products mentioned in this manual Loctite Registered Trademark of the Loctite Corporation Fox Registered Trademark of Fox Shox Hi Fax Trademark of Himont Advanced Materials 175 INDEX ACCESSOTIES ooon eee eee 60 65 Adjustment Backrest 59 Adjustment Front Suspension 44 50 Adjustment Handlebar 59 Adjustment Headlight 129 Adjustment Indy Select Front Track SHOCK aiin ales aoe es 54 Adjustment Indy Select Rear Shock 55 Adjustment Rear Rear Scissor Stop 58 Adjustment Rear Torque Arm SKS Mod C182 Ae e h duis avin GA oe 53 Adjustment Rear Torsion Spring Xtra 12 53 Adjustment Steering 144 Adjustment Rear Suspension 49 Adjustments Carburetor 118 Air Intake System 111 112 Alignment Ski 00 145 Anti Theft System 170 Backrest 23 reeni envio ee shee sarees 59 Backrest Adjustmen 59 Battery pies cbs tase see sees 153 155 Battery Connections 154 Battery Fluid 0 153 Battery Installation 155 Battery Removal 154 Bearing Driveshaft 107 Bearing Jackshaft 107 Before Starting the Engine Brakes iarsan ge cee ee ed oes 66 67
90. mance PPS kit available for increasing damping If you desire to have the internal valving changed consult your dealer or refer to the suspension troubleshooting decal located under your hood or on the clutch guard Suspension Coupling On all Polaris snowmobile rear suspensions there are two torque arms that control the movement of the rail beam Prior to the advent of suspension coupling these torque arms could move independently of each other Rear suspension coupling links the movement of the front and rear torque arms to each other There are two types of rear suspension coupling Front To Rear Coupling and the Front Rear Scissor Stop FRSS The front rear scissor stop FRSS couples the movement of the front torque arm with the rear torque arm and limits the amount of independence between the movement of the front torque arm and the rear torque arm When hitting a bump the front torque arm starts to compress The FRSS links that movement to the rear torque arm causing it to compress and raise the rear suspension up as one allowing the suspension to hit the bump only once and eliminating kickback Your FRSS is preset at the factory Do not make any adjustments to the position of the FRSS or your ride will be compromised 56 THE PERFECT FIT Rear Suspension Adjustments Rear To Front Coupling and the Rear Rear Scissor Stop RRSS The rear rear scissor stop RRSS couples the movement of the rear torque arm with the fron
91. me Rear suspension Increase torsion spring preload bottoms too easily Increase rear shock compression damping by turning screw clockwise Increase torsion spring wire diameter see your dealer Rides too stiff in Check for binding suspension shafts and grease all pivot points rear Decrease torsion spring preload adjustments Decrease rear shock compression valving by turning screw counterclockwise if equipped with optional Indy Select shock Change to lighter valving if if equipped with Fox shocks Check for proper track tension Machine darts from Make sure skis are aligned properly side to side Make sure spindles and all steering components are free turning Make sure skags are straight on skis Check Hi fax and replace if worn Reduce ski pressure Reduce IFS spring preload Reduce rear torsion spring preload Front end pushes Check for worn skags Check for binding suspension shafts and grease all pivot points Increase IFS spring preload by adjusting cam or threaded ad juster Decrease front limiter strap length Steering is heavy Check ski alignment Check skags and skis for damage Reduce ski pressure Increase front track spring preload Reduce IFS spring preload by adjusting cam Reduce rear torsion spring preload Setting up for deep Change worn Hi fax snow operation Move front track shock assembly to upper position 160 TROUBLESHOOTING Suspension Troubleshooting EDGE RMK Solution perf
92. nd free operation SEE YOUR DEALER Clean and polish stationary shaft hub Replace ramp buttons and rollers SEE YOUR DEALER Inspect movable sheaves for excessive bush ing clearance and replace if necessary SEE YOUR DEALER Replace drive belt SEE YOUR DEALER Replace drive belt Adjust alignment offset Inspect and adjust or replace SEE YOUR DEALER Shift out of neutral Belt twisted spring broken weights stuck lubricated SEE YOUR DEALER Foreign object caught or Hi fax melted to track clips due to lack of lubrication Machine may be frozen to ground Track may be iced up Chain is loose or broken chain tightener is loose SEE YOUR DEALER TROUBLESHOOTING Engine Troubleshooting Noise in drive system Poor low RPM performance Engine doesn t start electric start models Engine doesn t turn Broken drive clutch components Bearing failure chaincase jack shaft or front drive shaft Drive belt surface flat spots Drive chain loose or worn sprocket teeth broken Worn drive belt Excessive belt sheave clearance Loose torque stop Sticky clutch Wire connections Seized engine Hydrostatic lock SEE YOUR DEALER SEE YOUR DEALER Inspect and replace if necessary Inspect and adjust or replace Inspect and replace if necessary SEE YOUR DEALER Inspect and adjust SEE YOUR DEALER SEE YOUR DEALER SEE YOUR DEALER Se
93. ng procedure keep the brake handle in as level a position as possible The reservoir must be in this position to minimize the possibility of air entering the system through the reservoir vent 127 MAINTENANCE General Maintenance Mechanical Brake Lever Travel AWARNING Improper brake adjustment could result in brake failure and lead to serious injury or death See your dealer for brake service Frequently inspect the brake lever reserve Firmly depress the brake lever and measure the clearance between the lever and the brake block This distance brake lever reserve A should be no more than 3 4 1 9 cm If brake lever reserve exceeds this amount see your dealer for service 128 MAINTENANCE General Maintenance Headlight Adjustment The headlight may be adjusted for vertical aim using the following procedure 1 Place the snowmobile on a level surface with the headlight Lamp Center approximately 25 feet 7 6m Height 2 5 1 cm from a wall 2 Measure the distance from the floor to the center of the headlight and make a mark on the wall 3 Start the engine and turn the headlight switch to high beam 4 Observe the headlight aim The most intense part of the headlight beam should be aimed 2 5 1 cm below the mark placed on the wall in Step 2 NOTE Rider weight must be included on the seat 5 Turn the adjustment nut A located inside the hood just below the headlamp open
94. ng the warranty period through a Polaris dealer There is a charge of 35 00 payable to Polaris Industries Inc REGISTRATION At the time of sale the Warranty Registration Form must be completed by your dealer and submitted to Polaris within ten days Upon receipt of this registration Polaris will record the registration for warranty No verification of registration will be sent to the purchaser as the copy of the Warranty Registration Form will be the warranty entitlement If you have not signed the original registration and received the customer copy please contact your dealer immediately NO WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR SNOWMOBILE IS REGISTERED WITH POLARIS Initial dealer preparation and set up of your snowmobile is very important in ensuring trouble free operation Purchasing a machine in the crate or without proper dealer set up will void your warranty coverage 171 WARRANTY WARRANTY COVERAGE AND EXCLUSIONS LIMITATIONS OF WARRANTIES AND REMEDIES The warranty excludes any failures that are not caused by a defect in material or workmanship This warranty does not cover accidental damage normal wear and tear abuse or improper handling This warranty also does not cover any snowmobile that has been altered structurally neglected improperly maintained used for racing or used for purposes other than for which it was manufactured or for any damages which occur during trailer transit or as a result of unau
95. ns 12 SAFETY Operator Safety AWARNING Driving a snowmobile requires your full attention DO NOT drink alcohol or use drugs or medications before or while driving They will reduce your alertness and slow your reaction time In most states and provinces it s prohibited by law to drive while intoxicated or under the influence of drugs Polaris produces high performance snowmobiles capable of traveling at high speeds Extra caution must be observed to ensure operator safety Make sure your snowmobile is in excellent operating condition at all times We strongly recommend that the operator check major and vital safety components before every ride All Polaris snowmobiles are designed and tested to provide safe operation when used as directed Failure of critical machine components may result from operation with any modifications especially those that increase speed or power DO NOT MODIFY YOUR MACHINE The snowmobile may become aerodynamically unstable at speeds higher than those for which it is designed Loss of control may occur at higher speeds Modifications may also create a safety hazard and lead to bodily injury The warranty on your entire machine is terminated if any equipment has been added or any modifications have been made to increase the speed or power of the snowmobile 13 SAFETY Operator Safety Stay Away From Moving Parts AWARNING Never hold the snowmobile up or stand behind it while warming up the
96. nt Repairs use only genuine top quality Polaris parts Peace of mind The Polaris Extended Service Contract is honored by all authorized Polaris snowmobile dealers in North America How ever when possible please contact the selling dealer There are no cards for you to carry as repair authorization as your dealer is only a phone call away Because the extended service contract is transferable for a 35 00 fee the snowmobile s resale value is increased The Polaris Extended Service Contract is very affordable and can be financed with the Polaris Star Card Conditions The Polaris Extended Service Contract must be purchased within 90 days from the date of the unit s registration Each repair visit it subject to a 50 00 deductible The Extended Service Contract applies to the first 5000 miles or two calendar years from date of registration whichever comes first Tampering with the odometer shall void the Extended Service Con tract No extensions to coverage under the Extended Service Con tract will be given Snowmobiles used in commercial purposes or for racing are excluded from coverage Coverage Second year coverage is extended to 1997 and 1998 model engine failures caused by defects in material and workmanship as determined by Polaris in its sole discretion Used snowmobiles are not eligible under this program Following is a partial list of exclusions from coverage Damage due to accident fire explosi
97. ocknuts A except on models with Xtra Lite suspension Tighten or loosen the track adjusting screws B as necessary to provide equal adjustment on both C Track sides of the track 141 MAINTENANCE Track Maintenance If the track needs adjustment continued 8 Repeat measurement on the other side of the track NOTE Check more frequently when machine is new 9 Start machine and slowly rotate the track at least five revolutions Let the track come to a stop do not apply brakes 10 Check track alignment see page 142 and adjust as necessary 11 Tighten locknuts A except on models with Xtra Lite suspension 12 Tighten idler shaft bolts D and torque to 35 ft lbs Track Alignment Periodically check that the track is centered and running evenly on the slide rails Misalignment will cause excessive wear to the track and slide rail 1 Safely support the rear of the machine with the track off the ground 2 Start the engine and apply a small amount of throttle until the track turns slowly at least five complete revolutions Stop the engine and let the track come to a stop do not apply brakes 3 Inspect track alignment by looking through the track window to make sure the rails A are evenly spaced on each side If the track runs to the left loosen left locknut and tighten the left adjusting bolt If the track runs to the right loosen right locknut and tighten the right adjusting bolt 4 After ad
98. ommends that only O E M belts be used Other belts may match the dimensions but can drastically change the shift pattern resulting in poor performance See your dealer for service and adjustments NOTE A worn belt will continue to function but will not deliver maximum performance Always carry a spare belt in case of an emer gency See page 132 for belt removal and installation Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position Place a straight edge on the belt A and apply downward pressure while measuring at point B This measurement should be 1 1 4 135 MAINTENANCE General Maintenance Clutch Center Distance See your Owner s Manual Specification Supplement for recommended center distance for your machine If adjustment is necessary see your dealer Due to tolerances in belt length it may be necessary for your dealer to make minor adjustments in the driven clutch to achieve correct belt tension Torque Stop If your snowmobile is equipped with an engine torque stop 1 periodically check torque stop clearance With clutches in proper alignment the torque stop clearance should be a minimum of 010 to a maximum of 030 from the engine case 2 Adjust if necessary and lock the jam nut Reverse Kit Maintenance If your snowmobile is equipped with reverse or if you have a reverse kit installed it s e
99. on theft or other causes beyond Polaris control Damage caused by the failure of other components of the snowmo bile 174 WARRANTY Polaris Extended Service Contract Coverage Exclusions continued Failures caused by improper fuel or oil Failures caused due to improper adjustments including but not limit ed to carburetor jetting and clutching Failure due to unauthorized service Failures due to lack of service as specified in the Owner s Manual or Polaris updates This includes off season storage as listed in the Owner s Manual Failure due to unauthorized parts or modifications Normal wear parts including but not limited to spark plugs hoses batteries controls and recoil ropes Gaskets and intake and ex haust manifolds are covered excluding paint coverage Electrical coverage is limited to the CD and ECU box coils stator plate and sensors Wiring and other electrical components are ex cluded from coverage Oil injection system coverage is limited to the control module sen sors solenoids pump and throttle cable switch Cooling system coverage is limited to the water pump assembly and components fan fan bearings temperature sensor gasket and seals Non wear related carburetor parts are covered Carburetor jetting and adjustments are excluded from coverage The fuel pump and choke are covered Clutches and related clutch parts including but not limited to the drive belt are exc
100. orm only one change at a time Rear suspension bottoms too easily Rides too stiff in rear Too much weight transfer when climbing Too little weight transfer when climbing Machine darts from side to side Front end pushes Steering is heavy Adjust torsion spring blocks Increase torsion spring diameter see your dealer Increase rear shock compression damping by turning screw clockwise RMK or rotating knob towards the right side of the machine Vertical Edge Check for binding suspension shafts and grease all pivot points Verify sag dimension refer to set up decal or page 50 Adjust torsion spring blocks Install optional torsion springs see your dealer Decrease rear shock compression damping by turning screw counter clockwise RMK or rotating knob towards the left side of the machine Vertical Edge Verify sag dimension refer to set up decal or page 50 Adjust torsion spring blocks Install optional torsion springs see your dealer Move limiter strap on front torque arm to high position See your dealer for optional mounting Verify sag measurement refer to set up decal or page 50 Adjust torsion spring blocks Install optional torsion springs see your dealer Move limiter strap on front torque arm to low position refer to set up decal or page 50 See your dealer for optional mounting Make sure skis are aligned properly Make sure spindles and all steering components are free turn
101. our machine is to install traction products See your dealer if you about installing studs and or carbides Many tracks with deep lug designs cannot be studded but your dealer will be able to offer advice and assistance NOTE Polaris does not recommend the use of traction products on WideTrak snowmobiles CAUTION If traction products are added to the track wear strips must be installed in the tunnel to avoid excessive wear Never add shims to the wear strip Track damage will result because of lack of clearance between upper carrier wheels and track Use of studs longer than 1 2 5 cm on machines equipped with center coolers will result in center cooler damage or damage to the tunnel Use only Polaris traction products on your snowmobile Track warranties are void if track damage or failure results from improper or excessive stud installation or the use of non Polaris traction products AWARNING Loss of control can result in serious personal injury or death Proper balance of traction products on the skis and track must be maintained to obtain proper vehicle control on hard packed snow or ice See your dealer for assistance 61 THE PERFECT FIT Accessories Traction Products IMPORTANT Before equipping your machine with traction products be aware of the laws in your area pertaining to the use of traction products Track studding will enhance braking control on hard packed snow or ice but extreme caution
102. p angles in reverse Transmission may not always be in the gear indicated by the shift lever Always apply throttle slowly On machines with reverse it is especially important to maintain track tension as specified in the Owner s Manual If specified track tension is not maintained severe damage to the machine may occur which may result in loss of vehicle control Loss of vehicle control may result in severe personal injury or death For more information See Operator s Safety and Maintenance Manual supplied with reverse kit SHIFT PATTERN Make sure lever is shifted completely to forward or reverse position Do not force into reverse If not able to shift to reverse apply throttle gently to move vehicle CAUTION Do not attempt to shift until machine has come to a complete stop or chaincase damage may occur 31 SAFETY Safety Decals And Locations Electronic Reverse Warning Decal 7 Some Polaris snowmobiles are equipped with electronic reverse and will have this electronic reverse decal Reverse operation even at low speeds may cause loss of control resulting in serious injury or death To avoid loss of control always e Look behind before and while backing e Avoid sharp turns e Shift to or from reverse only when stopped e Apply throttle slowly e For more information see your Owner s Manual Operation Warning Decal 8 The console of your machine has a WARNING decal The location of t
103. pistons and cylinder walls ePlug fouling Poor engine response to various throttle valve openings 118 MAINTENANCE General Maintenance Exhaust System Check the exhaust system for wear or damage at approximately 2000 miles 3200 km To inspect allow the engine and exhaust system to cool completely Open the hood and inspect the muffler and pipes for cracks or damage Check for weak or missing retaining springs or damper support grommets AWARNING Hot exhaust system parts can cause serious burns Allow adequate time for the exhaust system to cool Never perform this procedure with the engine running Engine Cooling Liquid Cooled Models The cooling system on liquid cooled models consists of the following major components Recovery tank Water pump Cylinders e Heads Inlet and outlet manifolds Pressure cap Heat exchangers 119 MAINTENANCE General Maintenance Coolant Mixture The coolant supplied in the system is a 50 50 mixture of ethylene glycol and distilled water This mixture provides protection against freezing at temperatures to 34 F 37 C If greater protection is required the percentage of antifreeze to water may be increased Use Premium 60 40 anti freeze coolant Never exceed a 60 antifreeze 40 water mixture Contact you dealer if greater protection is required NOTE Never add tap water to the cooling system Minerals cause deposits and may react adversely with the metals in the
104. ponsibility to operate your snowmobile with concern for others We do our part by manufacturing quieter machines we ask your help to further reduce the impact of noise by operating your snowmobile safely and responsibly Air Pollution Polaris engineers continuously investigate ways to reduce emission levels of two stroke engines We expect our efforts to lead to the reduction of potential air pollution In addition to our technological research we encourage government agencies manufacturers distributors dealers ecologists and other interested parties to work together to develop data on environmental topics HOW TO USE THIS MANUAL Preservation Of The Environment Polaris is committed to supporting an environmental education campaign We encourage state and provincial governments across the snowbelt to adopt rigorous safety training programs that encourage protection of our environment including wildlife and vegetation Snowmobile clubs and other organizations are working together to protect our environment Please support their efforts and do your part to preserve and protect our environment Respect your snowmobile respect your environment and you will earn the respect of everyone HOW TO USE THIS MANUAL Vehicle Identification Numbers Please record your snowmobile identification numbers below for future reference Tunnel VIN lower right side of the tunnel Engine Serial Number right front side of engine crankcase
105. proper operation Lighting Check Check the headlight high and low beam taillight and brake light for normal operation Mirror Adjustment Adjust your mirrors so they can be used to their full advantage Check Surroundings to Verify Clear Operating Area Make sure you have a clear area all around your snowmobile including an area clear of bystanders There s always the possibility of some sideways vehicle movement of applying a little more throttle than intended or of debris being thrown by the track If the surrounding area is clear you before you start you can devote your full attention to operating the snowmobile 71 NOTES SECTION 6 OPERATION Starting Your Engine 74 75 Engine Break In 0 0e0ee eee 76 77 Track Warm Up 0c eee e eens 78 79 RUC wicctueiuy esta ecenemoer ee foe 80 82 OW eee eit aaa a a aa a ob ANE a ara 83 84 Carburetion i fewe ev ow veveens dveweevee s 85 Engine Stop Switch 0eeeeeees 86 Throttle Safety Switch 0005 86 Throttle Lever oo ece ee eee ee ce ee eee tee 87 Emergency Stopping and Starting 88 89 Reverse Operation 00eeeeeees 90 92 Dally Storage n6 i6 ee oe eee ewtiews de eweevedes 92 TOWING nips oa aise etna hate era wa a eae 93 Section 6 explains proper engine break in operation of features and operating procedures 73 OPERATION Starting Your Engine AWARNING Before start
106. r the machine to the ground 4 Grasp the skis by their front loops and move them from side to side This will loosen frozen snow from the ski bottoms allowing the machine to move forward more easily 78 OPERATION Track Warm Up 5 The engine drive system and track are now properly warmed up and the machine may be driven following normal safety practices AWARNING Always inspect for track damage before operating the snowmobile Use of traction products such as studs ice growsers etc will increase the possibility of track damage and or failure This could cause loss of control resulting in serious injury or death 79 OPERATION Fuel Gasoline is extremely flammable and explosive under certain conditions A gt gt FP gt 80 Always stop the engine and refuel outdoors or in a well ventilated area Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored Do not overfill the tank Do not fill the tank neck If you get gasoline in your eyes or if you swallow gasoline see your doctor immediately If you spill gasoline on your skin or clothing immediately wash it off with soap and water and change clothing Never start the engine or let it run in an enclosed area Gasoline powered engine exhaust fumes are poisonous and can cause loss of consciousness and death in a short time AWARNING The engine exhaust from this product contains
107. rating Check the color of the spark plug immediately after the engine has been warmed up and after the snowmobile has been driven at higher speeds NOTE Incorrect fuel mixture can often cause a spark plug to appear too dark or too light in color Before changing spark plug heat ranges be sure the correct main jet is installed in the carburetor s Refer to the Owner s Manual Supplement or see your dealer Normal The insulator tip is gray tan or light brown There will be a few combustion deposits but the electrodes are not burned or eroded This indicates the spark plug is the proper type and heat range for the engine and the service Overheating The insulator tip is white General causes are use of an improper spark plug or incorrect carburetion adjustments Wet Fouled The insulator tip is black A damp oily film covers the firing end and there may be a carbon layer over the entire nose Generally the electrodes are not worn General causes are excessive oil use of non recommended injection oil excessive idling idle set too low or too rich or weak ignition output 113 MAINTENANCE General Maintenance CAUTION If spark plug color indicates overheating the cause of this condition must be identified and corrected to prevent damage to the engine Spark Plug Removal and Replacement AWARNING Hot parts on the exhaust system or engine can cause burns and result in serious injury Never attempt to remove
108. rn Never bleed the cooling system or remove the pressure cap when the engine is warm or hot Serious personal injury could result If the pressure cap A needs replacement contact your dealer for the correct part Use of a non standard pressure cap will not allow the recovery system to function properly Recovery System Models If the coolant level becomes low in the recovery tank bleed the system of any trapped air Visually inspect the coolant filter B and replace it if it s dirty 1 Fill the recovery tank with coolant to the maximum indicated mark 2 Elevate the front end of the machine slightly to aid bleeding of the heat exchangers 3 With pressure cap removed add coolant and fill to the top of the filler neck 4 Install the pressure cap with the lever lock up in its release position 5 Run the engine at various RPMs for two to three minutes to purge the system of trapped air 6 Close the lever lock and check the recovery tank fluid level 121 MAINTENANCE General Maintenance CAUTION Most cooling systems are equipped with a filter that should be periodically inspected or replaced If coolant flow becomes restricted or plugged coolant loss air lock or engine damage may result Surge Tank Models 1 Remove the pressure cap and fill the recovery tank with properly mixed coolant to the maximum indicated mark 2 Elevate the front end of the machine slightly to aid in bleeding of the heat ex
109. rossing the face of a slope may result in loss of balance and machine roll over causing serious injury or death Use caution and good judgement when driving in hilly terrain Operating in hilly terrain requires extreme caution to maintain balance and avoid roll over If climbing a hill is unavoidable keep all your weight low and forward If you must cross the face of a slope keep your weight on the uphill side of the machine to maintain proper balance and avoid possible roll over Slow down when reaching the crest of a hill Be prepared to react to obstacles sharp drops or other people or vehicles that may be on the other side of the hill If you re unable to continue up a hill turn the machine downhill before it loses momentum If this isn t possible spin the track just enough to dig in to prevent it from rolling back down the hill Stop the engine and set the parking brake if equipped Keeping away from the downhill side of the machine pull the rear of the snowmobile around and point the front end and skis downhill Remount the machine restart the engine release the parking brake and descend the hill carefully 20 SAFETY Operator Safety Riding Downhill When riding downhill shift your weight to the rear of the machine and reduce your speed to a minimum Apply just enough throttle to keep the clutch engaged allowing the engine s compression to help slow the machine and keep it from rolling freely downhill
110. sion 2a Limiter strap in high position increases ski pressure 2b Limiter strap in low position decreases ski pressure 3a Turn the knob to the left for a softer ride 3b Turn the knob to the right for a stiffer ride 4a Soft Tension long end of cam to front 4b Medium tension short end of cam up 4c Firm tension long end of cam up 51 THE PERFECT FIT Rear Suspension Adjustments Rear Suspension Initial Spring Preload Setting Xtra 10 EDGE and Xtra Lite Sag Method To set up the EDGE rear suspension torsion spring preload measure the distance between the ground and rear bumper This is measurement X Take the first measurement with no rider and with the rear suspension at full extension NOTE The rear bumper may need to be lifted upward slightly to fully extend the rear suspension Next have the rider drop down hard on the seat and bounce up and down several times collapsing the rear suspension With the rider seated measure the distance between the round and the rear bumper at the Stace location used for eN goss X This is measurement Y GO To determine sag commonly referred to as ride in subtract measurement Y from X Sag X Y Adjust sag by rotating the torsion spring preload cams located on the rear torque arm Use the illustration or the decal found under the hood for reference The ideal amount of Sag for the EDGE rear suspension is four inches X Y 4 If the rear suspension rides in le
111. skags will adversely affect handling Loss of vehicle control may result causing serious injury or death See your dealer s studding chart for recommended skags If you install longer or more aggressive carbide skags than the original equipment it may also be necessary to add track studs to maintain proper vehicle control while turning on hard packed snow or ice Check skags weekly to maintain positive steering characteristics Skags must be replaced when worn to half their original diameter IMPORTANT Carbide skags must be replaced if any abnormal wear or chipping is found Skag Identification A Steel ski 1 Standard skag 2 E Z Steer skag B Composite ski 1 Skag Skag Replacement 1 Raise and support the front ofthe machine so the skis are approximately 6 15 2 cm from the ground 2 Remove the attaching nuts and pry the skag downward 3 Remove the forward portion of the skag Reverse this procedure for new skag installation 147 MAINTENANCE Suspension Maintenance Hi Fax Wear Check Hi fax wear by measuring thickness at several points along the rail Replace Hi fax when a thickness of 5 16 8 cm is reached 7 16 on Xtra Lite models Take the machine to your dealer for Hi fax replacement Measure Hi fax thickness NOTE Hi fax wear pat terns are somewhat different on XTRA 12 suspensions The rear portion will wear i rapidly at first
112. specially important to maintain track tension as specified on page 140 AWARNING If specified track tension is not maintained serious damage to the snowmobile may occur which can result in loss of vehicle control Loss of control can result in serious personal injury or death Allow the engine to reach idle speed before attempting to shift into or out of reverse CAUTION If machine has not come to a complete stop before shifting damage will occur to chaincase or transmission 136 MAINTENANCE General Maintenance Accessory Reverse Kit If you ve had a reverse kit installed on your snowmobile some maintenance will be required Follow these recommendations Chain Tension Maintain the proper chain tension as outlined on page 123 Oil Level Maintain the oil level between the safe marks as indicated on the oil bottle see page 84 Oil Change Have the oil changed annually by your dealer 137 MAINTENANCE General Maintenance Tool Kit A tool kit is included with your machine for emergency and routine maintenance Included in the kit are A Emergency Start Strap B Phillips Screwdriver C Tubular Socket D Tubular Socket Handle E Wrench F Shielded screwdriver only models with Indy Select or AFX shocks Always keep the tool kit with the snowmobile If necessary a replacement tool kit may be purchased from your Polaris dealer Tool Pouch Clip Some Polaris snowmobiles are eq
113. specially overnight always make sure the skis and track are loosened from ice and snow before attempting to drive Apply the throttle with enough authority to put the machine into motion but always operate within safety limits and on 2 Up machines with respect for a passenger See page 74 for more detailed instructions on cold weather drive away Machine Maneuverability Control and maneuverability comes not only through the steering and skis maximum control is achieved by shifting of body weight Maneuverability will change for lighter operators or machines designed to carry a load or a passenger 22 SAFETY Operator Safety Powder Snow Operation Moveable hood closures are included on some Polaris snowmobiles They are normally left open and are located on the front upper and lower hood openings If operating in deep snow or in extreme cold conditions below 20 F Polaris recommends closing the upper hood closure AWARNING Do not drive for prolonged periods on blacktop gravel or ice Doing so could cause irreversible track damage and lead to serious personal injury Since snow provides the only lubrication for the power slide suspension and on liquid cooled models cooling for the engine adequate snow cover is a requirement for operation of your machine Driving in too little snow will result in excessive wear and damage to the slide rail track and or engine If the machine becomes stuck in snow clear the runnin
114. ss than three inches or more than five inches with the torsion spring preload cams at their maximum range of adjustment optional torsion springs softer or stiffer respectively may be required This is only an initial set up and final spring preload may vary based on rider preference and riding conditions 52 THE PERFECT FIT Rear Suspension Adjustments Rear Torsion Spring Adjustment Xtra 12 To adjust rear torsion spring tension rotate the two position cam using the engine spark plug tool la Soft Tension long end of cam to front 1b Medium Tension short end of cam up Different rate torsion springs are available if greater tension is desired Contact your dealer for more information Rear Torque Arm Adjustment SKS Models On SKS models only the rear torque arm may be lowered from the stock mounting position A to an optional position beneath the tunnel bend line B Install a replacement bolt into the stock mounting position to secure the rear suspension mounting pad to the tunnel See your dealer for more information Moving the rear torque arm below the tunnel will improve deep snow mobility 53 THE PERFECT FIT Rear Suspension Adjustments Indy Select Front Track Shock Some snowmobiles are equipped with the Indy Select front track shock which allows the driver to make adjustments to the compression valving by turning the screw located near the base of the shock Adjustment Locate
115. t torque arm and limits the amount of independent movement between the rear torque and the front torque arm Adjusting the RRSS either allows more weight to transfer to the rear for more traction or allows less weight to transfer to the rear resulting in improved cornering performance An adjustment dot is located on the RRSS This dot is on the longest end of the scissor stop Rear Rear Scissor Stop RRSS Attributes Moving the RRSS to a higher position or forward hole will have the following effects on the suspension Reduced weight transfer Improved chatter bump ride Improved cornering performance 57 THE PERFECT FIT Rear Suspension Adjustments Weight Transfer During Acceleration Xtra 10 and EDGE Rear Rear Scissor Stop RRSS The preferred method for controlling weight transfer during acceleration of Q the EDGE rear suspension is by adjusting the rear rear scissor stop RRSS The RRSS is located in the ROTATE best overall trail riding position when delivered from the factory To decrease weight transfer under acceleration for improved cornering rotate the RRSS to a higher position with the scissor stop tool 1 located in your tool kit To increase weight transfer or ski lift during acceleration move the RRSS to the rearward hole on high position The RRSS may also be rotated to a lower position for even more weight transfer if desired A Stock Position This setting is most desirable for
116. teering System 2 00eeeeee 144 147 Suspension Maintenance 148 149 Extended Storage 2 00 150 152 Battery cc2etanise esis caw Qcchewer cat 153 155 This section defines your role and your dealer s role in your snowmobile s regular maintenance If you re interested in more information about servicing your own machine contact your dealer for a Polaris Snowmobile Service Manual 95 MAINTENANCE Polaris Recommended Maintenance Program To ensure many trouble free miles of snowmobiling enjoyment follow recommended regular maintenance and service checks outlined in this manual The recommended maintenance schedule on your snowmobile calls for service and maintenance inspections at 150 miles 240 km 1000 miles 1600 km and 2000 miles 3200 km These inspections should be performed by a qualified service technician For continued optimum performance and component life continue maintenance checks at 1000 mile 1600 km intervals All necessary replacement parts and labor incurred with the exception of authorized warranty repairs become the responsibility of the registered owner If during the course of the warranty period part failures occur as a result of owner neglect in performing recommended regular maintenance the cost of repairs are the responsibility of the owner Personal safety is critical when attempting to service or adjust your snowmobile If you re not familiar wit
117. the adjustment screw A near the base of the shock In half turn increments turn the screw clockwise to increase compression valving and stiffen the ride or counterclockwise to reduce compression and soften the ride There are approximately three full turns of adjustment available 54 THE PERFECT FIT Rear Suspension Adjustments Indy Select Rear Shock Some snowmobiles are equipped with the Indy Select rear shock which allows for adjustments to the compression valving by turning the adjustment screw located near the base of the shock Adjustment Locate the adjustment screw A near the base of the shock In half turn increments turn the screw clockwise to increase compression valving and stiffen the ride or counterclockwise to reduce compression and soften the ride There are approximately three full turns of adjustment available If bottoming continues after the screw has been turned fully clockwise the torsion spring should be adjusted see page 53 Return the screw to its original starting position after the torsion spring has been tightened 55 THE PERFECT FIT Rear Suspension Adjustments Optional Coil Springs Different rate coil springs are available for some shocks if a firmer ride is desired Contact your dealer for more information Position Sensitive Shock PPS There are no external adjustments on the position sensitive shock There is a perfor
118. the headlight 17 SAFETY Operator Safety Know the Limitations of the Machine and Your Skills as a Driver Slow down when traveling near poles posts or other obstacles Be especially alert if you re snowmobiling after dark Always be on the alert for wire fences Single strands are especially dangerous since there may be a great distance between posts Guy wires on utility poles are also difficult to distinguish Make sure the way is clear before crossing railroads and other roads and highways The noise of your machine will drown out the sound of approaching vehicles Look ahead behind and to both sides before turning or crossing railroad tracks or highways Steep embankments may also hide your view Always leave yourself a way out Ls Variances in snow depth and or water currents may result in uneven ice thickness Always check with local residents or authorities for general information on conditions when traveling on lakes and streams that are strange to you Before riding your machine on a frozen body of water be sure the ice is thick enough to support the machine and its operator as well as the force created by a moving vehicle You may drown if you and the snowmobile break through the ice When teaching inexperienced operators to ride set up a predetermined course for practice Make sure they know how to drive and control the snowmobile before allowing them to make longer trips Teach them proper snowmob
119. thorized service or the use of unauthorized parts In addition this warranty does not cover physical damage to paint or finish stress cracks tearing or puncturing of upholstery material corrosion or defects in parts components or snowmobile due to fire explosions or any other cause beyond Polaris control This warranty does not cover the use of unauthorized lubricants chemicals or fuels that are not compatible with the snowmobile The exclusive remedy for breach of this warranty shall be at Polaris exclusive option repair or replacement of any defective materials or components or products THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS WARRANTY POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIPTION WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR ANY OTHER CONTRACT NEGLIGENCE OR OTHER TORT OR OTHERWISE Some states do not permit the exclusion or limitation of incidental or consequential damages or implied warranties so the above limitations or exclusions may not apply to you if inconsistent with controlling state law 172 WARRANTY ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE ABOVE ONE YEAR WARRANTY PERIOD POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANT
120. to refill your battery Never allow cleaning solution or tap water to enter the battery Battery Removal AWARNING Batteries contain gases that can explode Whenever removing or installing the battery disconnect the negative black cable first and reinstall the negative cable last to avoid the possibility of explosion Disconnect battery hold down straps Remove battery vent tube from battery Disconnect black negative battery cable first Disconnect red positive battery cable second Carefully lift the battery out of the snowmobile Do not tip it sideways or spill electrolyte nNABWON PR ACAUTION Battery electrolyte contains acid If electrolyte spills on the snowmobile immediately wash it off with a solution of one tablespoon baking soda and one cup water to prevent damage 154 MAINTENANCE Battery When your snowmobile is placed in storage for one month or more Remove the battery Charge it to the proper level Store it in a cool dry place Before using the battery take it to your dealer for testing and recharging Batteries may freeze if not fully charged resulting in cell damage Charge Condition Will Freeze At 100 15 F 59 C WF GEO FF CRO FOO 0 18 F 8 Battery Installation AWARNING Batteries contain gases that can explode If the battery vent tube is pinched or kinked battery gases could accumulate Whenever removing or installing the battery disconn
121. track A loose track or flying debris could cause serious personal injury or death We recommend having your dealer perform track service and alignment procedures Be alert when riding and remain properly seated to stay clear of the track Your snowmobile is propelled by a revolving track that must be partially exposed for proper operation Serious injuries may result if hands feet or clothing become entangled in the track AWARNING Stop the engine before attempting adjustments If contact is made with fingers or clothing the moving parts of an engine can cause serious injury Never attempt adjustments with the engine running Turn off the ignition raise the hood make the adjustment secure shields and guards secure the hood and then restart the engine to check its operation 14 SAFETY Operator Safety Be Seated and in Position to Control the Vehicle AWARNING Improper riding position may seriously reduce your ability to control the machine and may result in serious injury or death Always be properly seated and in position to control your vehicle Operating a snowmobile requires skill and balance for proper control Rider positions may vary from person to person as each becomes more skilled but under most conditions the proper position is to be seated with feet on the running boards and comfortably positioned for proper throttle brake and steering control AWARNING Use of a backrest may hind
122. uipped with a tool pouch clip G located inside the flap on the back of the seat Use this clip to secure the tools and keep them from bouncing around during snowmobile use 138 MAINTENANCE General Maintenance For Your Protection For added protection carry the following items on your snowmobile at all times e Spare Drive Belt e Extra Set of Spark Plugs e Tow Rope e Extra Oil e Fuel Deicer e Winter Survival Kit e Trail Map e Owner s Manual e First Aid Kit Fall Tune Up For maximum performance arrange for a fall service tune up with your Polaris dealer His experienced and trained service technician will keep your machine in peak operating condition Maintenance Items The tools and maintenance items mentioned in this book as well as a long line of other Polaris accessaries are available at your Polaris dealer 139 MAINTENANCE Track Maintenance Track Tension Data Suspension Measurement Measurement See Owner s Location Manual Supplement for type XTRA 12 121 none 2 behind rail bumper 1 2 1 27 cm free hanging XTRA 12 133 none 16 ahead of rear 1 1 1 8 2 54 2 86 idler shaft cm free hanging XTRA 10 121 133 10 Ibs 4 54 kg 16 ahead of rear 3 8 1 2 1 1 3 cm 136 idler shaft WideTrak Type 10 lbs 4 54 kg 16 ahead of rear 3 4 1 1 9 2 5 cm idler shaft XTRA Lite 121 10 lbs 4 54 kg 16 ahead of rear 3 8 1 2 1 1 3 cm 133 136
123. ver Use the brake lever lock only when you want the machine to remain stationary for example when parked on an incline for a period of five minutes or less To apply the lock squeeze the brake handle and push forward on the brake lever lock Hold the lock forward and release the brake handle If the brake handle is squeezed tightly enough the lock will move freely into place Do not force the lock or it may break To release the lock squeeze the brake handle until the lever returns to the unlock position The park brake light on the console will light up when the park brake lever lock is set and the engine is running It will also be lit when the service brake is in use If the park brake light does not come on when the park brake or service brake is in use have it serviced by your dealer 1 Brake Handle 2 Park Brake Lever Lock not all models have a park brake 3 Master Cylinder Reservoir Cover 4 Fluid Level Indicator AWARNING If the park brake lever lock is partially or entirely engaged while riding overheating of the brakes could occur resulting in brake damage In extreme cases it could cause a fire which could result in serious injury or death 69 GETTING READY TO RIDE Check Before Starting Engine Check for Proper Operation of Steering System Manually turn the skis completely to the right and to the left If any difficulty is encountered check for ice and snow build up that may be obstructing the
124. wo pumps Coupler Greasing WideTrak Grease the couplers on the driveshaft and jackshaft Grease points are indicated by a x 1 Jackshaft 2 Driveshaft 3 Transmission MAINTENANCE 107 MAINTENANCE Lubrication Throttle Cable Lubrication Lubricate the throttle cable 1 with Polaris Cable Lubricant PN 2870510 With the engine off turn the handlebars to the left and lubricate liberally as shown Choke and Cable Lubrication Lubricate the choke slide 2 and cables with Polaris Cable Lubricant PN 2870510 Before turning the engine off operate the choke intermittently to draw moisture out of the choke plunger area and reduce the possibility of the choke becoming frozen 108 MAINTENANCE Lubrication Chaincase Oil Level It s the operator s responsibility to check and maintain the proper chaincase oil level To check the oil level place the machine on a level surface The oil level should be between the safe marks on the dipstick A Add Polaris chaincase oil PN 2871280 through the dipstick opening Do not overfill Flush the chaincase after the first 500 miles then every 1000 miles or seasonally Clean the magnetic plug B whenever checking or changing lubricant J Aa 109 MAINTENANCE Lubrication Gearcase Oil Level WideTrak Models It s the operator s responsibility to maintain proper gearcase oil level To c
125. xture may be caused by things like fuel line restrictions foreign matter in the carburetor or clogged fuel filters A rich mixture may be caused by snow build up on the pre filter in the air intake system Either condition may be caused by improper carburetor adjustment All carburetors have been preset at the factory for adequate fuel supply Higher altitude operation may require different adjustments and settings NOTE RMK models are preset to operate at altitudes of 6000 9000 feet above sea level See page 118 for more information Your dealer has the training and tools required to perform any adjustments for you AWARNING Carburetor adjustments must be performed by your dealer since mistakes may result in possible operator safety hazards as well as serious engine damage 85 OPERATION Engine Stop Switch Push down on the engine stop switch A to stop the engine in an emergency This will ground out the ignition and bring the engine to a quick stop To restart the engine the switch must be pulled up to ON Throttle Safety Switch Test the throttle safety switch system daily before operation While seated in a normal riding position and with the engine idling hold the throttle lever pin stationary by exerting pressure on the pivot pin in the direction shown in the illustration B Apply a slight amount of throttle A properly functioning switch must shut down the engine The throttle safety switch is
126. y FEATURES AND CONTROLS Features Hood Headlight Windshield Handlebar Seat Storage Rear Taillights Backrest Tunnel Extension 0 Passenger Hand Hold Strap SO Oe TONY B 12 13 14 15 16 17 18 19 20 21 Suspension Nosepan Trailing Arm Skis Front Bumper Console Rear Bumper Passenger Hand Hold Lifting Hand Hold Snow Flap 41 NOTES SECTION 4 THE PERFECT FIT Front Suspension Adjustments 44 48 Rear Suspension Adjustments 49 58 Handlebar Adjustment 0005 59 Backrest Adjustment 000eeeeee 59 Accessories iecerei irane ai nii 60 63 Polaris offers a wide range of adjustments so that every machine may be set up to suit individual needs This section explains how to tailor the suspension and other features for an optimum riding experience 43 THE PERFECT FIT Front Suspension Adjustments Break in the suspension for approximately 150 miles 240 km and re grease all suspension parts before fine tuning adjustments are made Settings will vary from rider to rider depending on rider weight vehicle speed riding style and trail conditions We recommend starting with factory settings and then customizing each adjustment individually to suit rider preference The machine should be methodically tested under the same conditions after each adjustment trail and snow conditions vehicle speed riding

Download Pdf Manuals

image

Related Search

Related Contents

Siemens Agents  TC-29RX30X TC-21RX30X GP41Z    ProVHDL      Using the Yaba X Surface Sound Speaker  Installations- Bedienungsanleitung... - Gemini    

Copyright © All rights reserved.
Failed to retrieve file