P32R Rogue Illum Kick Plate MASTER
Contents
1. b Measure 25 4mm 1in from point b to point Accessory a on the pierced wire Harness At points b amp bend the pierced wire gently to form the staircase shape 7 Multiple posi taps second accessory a Tap second accessory at point b making Sure to preserve staircase shape b After tapping second accessory form a strain relief loop for the tapped wire on the non pierce side as shown in Fig c and detailed in step 5b NOTE Do not secure before reading step 8 Repeat as necessary 8 Securing multiple posi taps on the same circuit a Secure the pierced and tapped wires from the first posi tap along with the tapped wire from the non pierce side of the 2nd posi tap to the body of the 2nd tap with electrical tape 2 revolutions b Secure the tapped wires from the non pierced sides of each tap to each other with electrical tape 2 revolutions at a distance of gt 6 35mm 0 25in from the head of last posi tap shown in Fig b Note Repeat as required Note No single wire should be posi tapped more than four times to maintain integrity 9 Multiple accessory taps on the same circuit secured a The first accessory is tapped relieved and has the pierced wire on the heat shrink side and the tapped wire on the non pierce side secured to the first tap as shown in Fig a b The second accessory is tapped relieved and has the pierced wire the tapped wire on the non pierce side and the tappe2. 6 ACCESSORY WEBSITE ADDRESS PAPER at 999 2 000 2 ACCESSES SERVICE CONNECTOR SOT INCLApED IN 491 _ 44 144 99966 62000 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 16 MECHANI ZATION ILLUMINATED KICK DRIVER SIDE ACCY_SER_CONN CONNECTOR E RED 2 3 4 BAT_SAVER 5 FR_DOOR_SW_LH 7 gt mi THRU_SIGNAL_1 8 RR_DOOR_RH 9 on RR_DOOR_LH 10 m A GND 12 TH12FW NH 11 Note Pin location is referenced looking into 7 8 9 10 11 12 wire side of connector ILLUMINATED KICK PLATE LH CONTROL Mechanization 1 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 16 MECHANI ZATION ILLUMINATED KICK PASSENGER SIDE T HT CONNECTOR 3 4 BAT_SAVER 5 FR_DOOR_SW_RH 6 TET r 9 _ C RR_DOOR_RH 9 RR_DOOR_LH aE a ore a BLK TH12FW NH x Note Pin location is referenced looking into wire side of connector ILLUMINATED KICK PLATE RH ___ MODULE i MODULE m Legend Posi tap Mechanization 2 99966 62000 10 10 2013
3. NOTE Do not remove clear protective film until procedure is complete NOTE Be sure to align kick plate bend with the formed edge in the door sill sheet metal Kick Plate Metal Edge 17 Fold the cardboard template provided in the kit and place it over the sheet metal edge of the door sill The cut out in the template should be aligned with the metal tab folded over the sheet metal just behind the front clip as shown Position the Kick Plate so the forward edge touches the template as shown The Kick Plate should be 6mm from the outermost edge of the door sill NOTE Flat wiring should be positioned directly behind the center harness clip Template Fold Front of vehicle 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 15 INSTALLATION 18 Carefully hold Kick Plate in position and remove the liners from the adhesive strips Apply minimum 15 Ibs of downward pressure evenly along the Kick Plate for at least 30 seconds NOTE Remove template once kick plate is pressed into place ee a Adhesive Liner 19 Cover the sheet metal edge under the wiring with a piece of protective tape Remove all Slack from the wiring at the plate end Carefully bend the flat wire to fit tightly over the sheet metal edge Flat Wire Kick Plate 20 Press the door seal welt back down into position Route the wires along the existing harness Secure with cable ties as shown Contr
4. of this connector with non Genuine Nissan or Infiniti or Nissan or Infiniti approved accessories or failure to follow the installation instructions for the connector contained in this package may result in damage to the accessory and or your vehicle Nissan or Infiniti is not liable for loss or damage due to improper installation or the installation of non Genuine or non approved accessories 7 PEREK 1 2 5 PINK BATSVR PINK BATSVR DK GRN FT DR SW RH Driver Side Accessory Service Connector LT GRN FTDR SW LH IGN Passenger Side Accessory Service Connector Pin location is referenced looking into face of connector 999Q9 AY001 Label IGN BAT TL_LMP RM LMP BATSVR FR_DR_SW_RH FR_DR_SW_LH THRU_SIGNAL_1 RR_DR_RH RR_DR_LH ACC ORANGE GND BLACK ACCESSORY SERVI CONNECTOR NOT INCLUDED IN KIT REFERENCE PART NUMBER 99909 001 Pin Label _1 IN 2 BAT 3 TiM __ 5 BATSWR__ __6 FR DR_SW_RH_ 7 FRDRSWLIH 8 THRU SIGNAL 1 _ 9 _ _10 RRDRIH _ put ac 12 GND Use posi taps to connect the wiring as follows DRIVER SIDE CONNECTIONS PASSENGER SIDE CONNECTIONS Red wire from the IKP Harness to the Red wire from the IKP Harness to the Pink wire on the Accessory Service Connector Harness Pink wire on the Accessory Service Connector Harness Black wire from the IKP Harness to the Black wire fr
5. GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION Illuminated Kick Plate Kit 2 APPLICATION Rogue PART NUMBER 999G6 G2000 Illuminated Kick Plate Kit 99909 001 Accessory Service Connector 4 KIT CONTENTS Item QTY Description Illuminated Front Kick Plates RH 1 Illuminated Front Kick Plates LH Non illuminated Rear Kick Plate RH 1 Non illuminated Rear Kick Plate LH ITEMS NOT IN KIT THAT MAY BE REQUIRED Accessory Service Connector NOTE ACCESSORY HARNESS MAY BE REQUIRED NOT INCLUDED IN KIT REFERENCE PART NUMBER 99909 001 TOOLS REQUIRED e Trim stick e Protective gloves e Panel popper tool e Electrical tape masking tape e Protective cloth e Alcohol wipes PRE I NSTALLATI ON CAUTI ON NOTES Dealer installation recommended Instructions may refer to Service Manual Installation may require special tools This part is to be installed within a surface temperature range of 60 110 F Install one side completely before starting the other side 4 CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Page 1 of 18 999G6 G2000 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 7 INSTALLATION OVERVIEW lt Front of Vehicle Accessory Lighting Control C
6. II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 14 CHECK OUT Inspect the vehicle for unfinished work 1 Open front left door 2 Verify the illuminated Kick Plate turns on 3 Push and hold the door status switch located on the vehicles center pillar The kick plate should turn off within a few minutes 4 Repeat steps 1 4 with the front right door 5 Verify the functionality of all electrical vehicle components where harnesses were accessed 6 Check and clear trouble codes DTC 7 If this vehicle will be returned to a dealer lot or showroom for an extended period of time be sure the extended storage switch is placed in the inventory position Refer to section 9 Vehicle Preparation 8 If vehicle is NOT going into storage reset the radio presets to the recorded settings Note When diagnosing electrical system problems first disconnect the accessory connectors and note effect on system Continue the investigation with the accessory connectors disconnected Remember to reconnect the accessories when the investigation is complete Page 18 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 15 BILL OF MATERIALS Illuminated Kick Plate Kit 999G6 G2000 Parts Contained Bag Labelled Installation Kit Qty Part Number PLATE KICKING FR OTR RH 99966 62010 PLATE KICKING FR OTR LH 999G6 G2020 PLATE KICKING RR OTR RH 999G6 G2030
7. accessories NOTE If unclear it is up to the responsible NTCNA Accessory Engineer to determine which of the methods above 15 the most appropriate Page 9 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION CAUTION e Ifa vehicle wire is being used by another accessory and posi Tap is present tap the accessory wire NOT the vehicle wire 11 Press the door seal welt back down into position Route the wires along the existing harness Secure with cable ties as shown Control NOTE Be sure to secure the Control Module Module just ahead of the middle clip with a cable tie Harness gt Cable Tie 12 Locate the driver side Accessory Connector plug It will be located below the dash along the outer wall of the footwell NOTE A previously installed accessory may be present If so carefully remove the Accessory accessory connector harness from the accessory connector plug before Plug posi tapping It is recommended that all posi tapping be completed before reattaching the accessory connector harness to the plug Driver Footwell Page 10 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 14 ACCESSORY CONNECTOR MECHANI ZATION CAUTION This Accessory Service Connector is for use only with Genuine Nissan or Infiniti or Nissan or Infiniti approved accessories Use
8. bend the flat wire to fit tightly over the sheet metal edge Flat Wire Kick Plate Page 6 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 12 POSI TAP INSTRUCTIONS Accessory Service Connector i Straight and evenly spaced all the way around ii Tighten and minimize gap wire jacket should be crushed f Tighten Straight and evenly spaced around Tight and no gap and test the signal Harness Page 7 of 18 1 Tap Accessory service wire a Identify and confirm correct wire in the Accessory Service Connector to be tapped b Remove cap slot side from tap body c Slide cap around single accessory wire d Position cap 6 35mm 0 25 in away from the heat shrink end of Accessory Service Connector measurement for first posi tap installed on the circuit e Tighten the tap TIGHT with finger pressure Tighten by another quarter turn NOTE Figures are not to scale 2 Inspect the tap to ensure correct installation a Pull on the wire lightly to ensure connection b Inspect the tap to ensure correct installation c Test the signal to ensure that it is working properly NOTE Avoid putting pressure on the vehicle wire and tap for the remainder of the installation 3 Tap accessory wire a Remove tap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side opening d Sprea
9. d the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure g Tighten by another quarter turn 4 Confirm the tapped accessory wire a Pull on the wire lightly to ensure connection b Inspect the tap to ensure correct installation c Test the signal to ensure that it is working properly 5 Forming strain relief loop always required a Gently bend the end of the pierced wire where it exits the cap down towards body of posi tap b On the tapped wire of the non pierce side starting at point b1 measure 50 8mm 2in to point b3 Make the first bend of the loop b2 half the distance measured 25 4mm 1in and up toward the body of the posi tap make the second bend of the loop b3 in towards the posi tap so it can be secured with electrical tape c Secure the pierced wire on the heat shrink side and the tapped wire on the non pierce side to the body of the tap with electrical tape 2 revolutions 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 12 POSI TAP INSTRUCTIONS NOTE If securing multiple taps to single circuit continue to Step 6 if tapping different circuits repeat steps 1 5 as required then proceed to step 10 6 Multiple posi taps on the same wire first tap a The first accessory is tapped relieved and secured as shown in Fig 1 thru 5 these steps are always the same
10. d wire from the non pierce side of the first posi tap secured to the second tap as shown in Fig b c Finally the tapped wires on the non pierce side of the first and subsequent posi taps are secured to each other as shown in Fig c Page 8 of 18 99966 G2000 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 12 POSI TAP INSTRUCTIONS 10 Multiple accessory taps on different circuits Service secured together Connector tapped accessories with wires already 6 35mm secured to tap bodies are stacked slightly staggered on top of each other as shown in Fig a b The tapped wires on the non pierce side of all the posi taps are secured to each other with electrical tape 2 revolutions at a distance of 6 35mm 0 25in as shown Fig b c The pierced wires of the first and subsequent posi taps are secured to each other with electrical tape 2 revolutions at a distance of 6 35mm 0 25in as shown in Fig CAUTION This Accessory Service Connector is for use only with Genuine Nissan or Infiniti approved accessories Use of this connector with non Genuine Nissan or Infiniti approved accessories or failure to follow the installation instructions for the connector contained in this package may result damage to the accessory and or your vehicle Nissan or Infiniti 15 not liable for loss or damage due to improper installation or the installation of non Genuine or non approved
11. in 3b To remove transit mode the cabin fuse block Once located check that it is in the Customer 1 Remove fuse cover lid position See below for reference 2 Push down shorting pin 3 2 times without turning vehicle Inventory Customer PULL UP PUSH DOWN To return to transit mode 2 Remove fuse cover lid 3 Pull up shorting pin INCORRECT CORRECT 4 Assemble fuse cover lid 5 Ign On 2 times without turning vehicle on 6 Confirm transit mode condition on meter NOTE Typical vehicle condition shown here Switch is easily identifiable by the permanent push pull fuse holder Actual position on the fuse block may vary vehicle to vehicle 4 Record customer radio presets NOTE USE CAUTION WHEN REMOVING RE I NSTALLI NG TRIM COMPONENTS TO AVOID DAMAGE SCRATCHES BREAKING OF CLIPS AND OR INTERIOR TRIM PANELS MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA WARNING FOR VEHI CLES WITH MANUALLY OPERATED SEATS Disconnect negative battery terminal before proceeding FOR VEHI CLES WITH POWER SEATS Disconnect negative battery terminal AFTER Step 3 10 Order of Installation 1 Remove panels and trim 3 Route Wiring 2 Install Kick Plate Assemblies 4 Reinstall all panels Page 3 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 11 INTERIOR PREPARATION BEGIN ON DRIVER SIDE 2 Place fingers at clip A which is located at inner rear and front end and pull
12. inated Kick Plate Kit 13 INSTALLATION Front of vehicle REAR DOORS NON ILLUMINATED 25 Clean all mounting surfaces with alcohol wipe before final installation 26 Carefully flip the driver rear Kick Plate over Partially peel away enough of each adhesive liner to fold down a flag that will extend beyond the outer edge of the kick plate 27 Place rear kick plate into position on the Rear Kick Plate door sill The rear edge should be 30mm from the end point of the formed edge in the sheet metal of the door sill as shown Outer edge of kick plate should be 5mm from the outermost edge of the door sill NOTE Be sure to align kick plate bend with the formed edge in the door sill sheet metal omm Kick Plate Front of vehicle Metal Edge Page 16 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 28 Carefully hold rear kick plate in position and remove the liners from the adhesive strips Adhesive Liner Apply minimum 15 Ibs of downward pressure evenly along the Kick Plate for at least 30 seconds Liner gt SZ SO Front of vehicle i S Adhesive 30 REPEAT STEPS 25 THROUGH 28 FOR THE PASSENGER SIDE 31 Remove clear protective film from all plates NOTE Be sure to trim all cable ties Check all wiring Make sure all trim is in place and clips are securely fastened Page 17 of 18 999G6 G2000
13. ing up through the existing harness clips towards the footwell NOTE Do not remove clear protective film until procedure is complete NOTE Be sure to align kick plate bend with the formed edge in the door sill sheet metal Kick Plate Metal Edge Page 5 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION and place it over the sheet metal edge of the door sill The cut out in the template should be aligned with the metal tab folded over the sheet metal just behind the front clip as shown Position the Kick Plate so the forward edge touches the template as shown The Kick Plate should be 6mm from the outermost edge of the door sill Template Flat Wire NOTE Flat wiring should be positioned directly behind the center harness clip Folded Metal lt Front Clip Middle Clip Fig 8 8 Fold the cardboard template provided in the kit Template nn Fold Front Edge of Kick Plate Front of vehicle Front of vehicle A Fig 9 9 Carefully hold Kick Plate position remove the liners from the adhesive strips Ad hesive Liners Apply minimum 15 Ibs of downward pressure evenly along the Kick Plate for at least 30 seconds NOTE Remove template once kick plate is pressed into place 10 Cover the sheet metal edge under the wiring with a piece of protective tape Remove all slack from the wiring at the plate end Carefully
14. ol 1 Module H NOTE Be sure to secure the Control Module 1 just ahead of the middle clip with 52 cable tie NOTE Do NOT secure the wiring to the drain tube in 2 Cable Tie 9 IN K 14 18 99966 62000 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION Fig 21 21 Locate the passenger side Accessory Connector plug It will be taped up under the dash along the outer wall of the footwell Pull the plug free from the tape Accessory Connector Plug NOTE REFER TO ACCESSORY CONNECTOR DIAGRAM ON PAGE 11 22 Plug the Accessory Connector Harness into the vehicle connector plug on the passenger side HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 999Q9 AYOOO 23 Plug the Accessory Connector Harness into the vehicle connector plug on the driver side Bundle any excess wiring as shown and wrap with foam tape Use cable ties to secure the connector to the existing harness as shown NOTE A functionality test is recommended at this time Refer to Check Out procedure on page 18 24 Reinstall the side trim panels on both sides of the vehicle along the bottom door seals from the seat to the footwell See Figs 1 and 2 Note Be sure to align the rectangular carpet holes with the harness routing clips Page 15 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illum
15. om the IKP Harness to the LT GRN wire on the Accessory Service Connector DK GRN wire on the Accessory Service Connector Harness Harness Page 11 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 15 INSTALLATION 13 Plug the Accessory Connector Harness into the vehicle connector plug on the driver side Bundle any excess wiring as shown and wrap with foam tape Use cable ties to secure the connector to the existing harness as shown NOTE Refer to Posi Tap steps on pages 7 through 9 for proper wire wrapping procedures HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 99909 001 PASSENGER SIDE INSTALLATION 14 Carefully pull back carpet edge to expose existing harness and clips NOTE Clean all mounting surfaces with alcohol wipe before final installation 15 Carefully flip the passenger side Kick Plate over Partially peel away enough of each adhesive liner to fold down a flag that will extend beyond the outer edge of the Kick Plate Page 12 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 15 INSTALLATION Middle Clip Front Clip __ __ Fiat Wire _ Template Folded Metal 6mm Front Edge of Front of vehicle Kick Plate Page 13 of 18 16 Place Illuminated Kick Plate into position on the driver side door sill Feed the end of the wiring up through the existing harness clips towards the footwell
16. onnectors Modules 7 lt TO Connectors Driver Kick Plates CAUTION CRITICAL STEPS TO DISCONECT BATTERY e Allow 3 min after key off and doors closed for vehicle to time out if doors are opened again additional time may be required Disconnect negative terminal Allow an additional 3 min after negative terminal disconnect before seperating any electrical connectors 8 CRITICAL STEPS The following steps are critical and must be performed EXACTLY as specified to ensure proper installation Location of the lights must be followed exactly as described in this instruction Posi Tap instructions must be specifically followed as described Be sure to apply masking tape as needed in order to protect any areas that may become scratched or damaged by tools Be sure to apply foam tape to any wiring components that can be damaged over time by sharp edges Test the functionality of the kit before final clean up and reinstallation of interior panels Page 2 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 9 VEHICLE PREPARATION 1 Apply parking brake 2 Confirm the vehicle is no longer in the default shipping state Extended Storage Switch Pulled Up and BCM in Transit Mode Failure to confirm the vehicle has been removed from this state will result in the loss of normal vehicle operation 3a Locate the Extended Storage Switch
17. out with a slight 1 Move driver seat to full forward position rotating motion until clip A is popped loose Remove inner door sill trim panel then pull up to remove door sill trim panel mansas 5 Asi Clip A Underside of Door Sill Trim Panel 3 Move driver and passenger seat to full back position AY FOR VEHICLES WITH POWER SEATS Disconnect negative battery terminal at this time 4 Carefully pull up the door seal welt from bottom of dash to back of sill plate as shown 7 Fig 5 5 Remove one 1 fastener from the outer footwell gt gt trim panel LH Use a trim stick to carefully pry off the trim panel pulling the part horizontally toward center of vehicle NOTE Be careful not to damage the clip on the lower portion of the panel 6 REPEAT STEPS 1 THROUGH 5 FOR PASSENGER SIDE RH Page 4 of 18 999G6 G2000 II 10 10 2013 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION DRIVER SIDE INSTALLATION 5 Carefully pull back carpet edge to expose existing harness and clips NOTE Clean all mounting surfaces with alcohol wipe before final installation 6 Carefully flip the driver Kick Plate over Partially peel away enough of each adhesive liner to fold down a flag that will extend beyond the outer edge of the Kick Plate 7 Place Illuminated Kick Plate into position on the driver side door sill Feed the end of the wir
Download Pdf Manuals
Related Search