INSTALLATION AND OPERATION MANUAL Low Profile Long
Contents
1. 1 j i2spingwasher 4 37 rearsectionof handle FT as arsina 4 36 oaser 3 15 reinforced bar for canular 1 35 Jfrontsecionofhande 1 14 M8 0sunkhexbot 2 34 jM grasehoe 1 13 j Bfltwaser 4 33 j 2stpwaser 2 12 o8springwasher 4 32 jmd 1 11 jM iSsunkhexbot 2 31 998 1 10 oi8springwasher 2 30 jadeof nkbar 1 jbotoncauar 2 29 Jinkbr 2 8 javeoflfingam 1 28 j i2stpwaser 3 7 j 3osopwaser 2 27 joofinkbar 2 6 jMi bot 4 26 Jj bdSpn 1 4 116 spring washer 3 2 wem 1 i fe sep waster 2 2 Josef 1 Bend R Ranger PROVIDING AUTOMOTIVE SERVICE SOLUTIONS PROD 7 25 7 TERO OmU RT For Parts or Service Contact BendPak Inc Ranger Products Tel 1 805 933 9970 1645 Lemonwood Dr Toll Free 1 800 253 2363 oanta Paula CA 93060 Fax 1 800 933 9160 www bendpak com PROVIDINCG AUTOMOTIVE SERVICE SOLUTIONS Bend R Ranger PROD2. If the jack is accidentally subjected to an abnormal load or shock it must be taken out of service immediately and be inspected by a qualified repair or service center It is recommended that an annual inspection is performed on the jack and that any damaged or worn parts decals or warning labels be replaced with manufacturer s specified parts A WARNING ALTERATIONS Because of potential hazards associated with this type of equipment no alterations shall be made to the product FOR YOUR SAFETY AND TO PREVENT INJURY Use Service Jack for lifting purposes ONLY Always support vehicle with jack stands A WARNING THIS IS A LIFTING DEVICE ONLY DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK IMMEDIATELY AFTER LIFTING SUPPORT THE VEHICLE WITH APPROPRIATE MEANS DO NOT EXCEED RATED CAPACITY OVERLOADING CAN CAUSE DAMAGE TO OR FAILURE OF THE JACK LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE MANUFACTURER KEEP HANDS AND BODY CLEAR OF ALL PINCH POINTS CENTER LOAD ON SADDLE PRIOR TO LIFTING OFF CENTER LOADS MAY CAUSE DAMAGE TO JACK LOSS OF LOAD PROPERTY DAMAGE PERSONAL OR FATAL INJURY THIS JACK IS DESIGNED FOR USE ONLY ON HARD LEVEL SURFACES CAPABLE OF SUSTAINING THE LOAD USE ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN JACK INSTABILITY AND POSSIBLE LOSS OF LOAD NO ALTERATIONS TO THE JACK SHALL BE MADE READ STUDY AND UNDERSTAND THE OPERATING MANUAL PACKED WITH THIS JACK BEFORE O
3. PERATING FAILURE TO HEED THESE WARNINGS MAY RESULT IN LOSS OF LOAD DAMAGE TO JACK AND OR FAILURE RESULTING IN PROPERTY DAMAGE PERSONAL OR FATAL INJURY ASSEMBLY INSTRUCTIONS 1 Assemble Upper and Lower Handle insert into Handle Socket and tighten Bolt OPERATING INSTRUCTIONS BEFORE USE Air may become trapped in the hydraulic system during transit To purge air 1 Open release valve by twisting Handle counter clockwise 2 Pump Handle rapidly 4 6 full strokes This will expel air that may have entered oil passages during transit 3 Close release valve by twisting Handle clockwise and pump handle 4 f lift arm is raised jack is ready for use If not repeat this procedure A CAUTION BEFORE ATTEMPTING TO RAISE ANY VEHICLE CHECK VEHICLE SERVICE MANUAL FOR RECOMMENDED LIFTING POINTS OPERATION 1 To Raise Load Close release valve tightly by twisting Handle clockwise DO NOT OVERTIGHTEN Position jack under load so that saddle will contact load firmly and load is centered so it cannot slip Operate jack handle until saddle approaches the load Once again check to see that saddle is correctly positioned Raise load to desired height Place jack stands of appropriate capacity under the vehicle DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING JACK STANDS Place jack stands at vehicle manufacturer s recommended lift areas that provide stable support for the raised Vehicle Onc
4. PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION BY PROCEEDING YOU AGREE THAT A WARN N G YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF Wil THIS MANUAL FORWARD THIS MANUAL TO ALL OPERATORS FAILURE TO OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH REV B 02 05 15 INSTALLATION AND OPERATION MANUAL Low Profile Long Frame Floor Jack Model RFJ 3000LPF REV B SHIPPING DAMAGE CLAIMS When this equipment is shipped title passes to the purchaser upon receipt from the carrier Consequently claims for the material damaged in shipment must be made by the purchaser against the transportation company atthe time shipmentisreceived READ FIRST o Do not operate this machine until you read and understand all the dangers warnings and cautions in this manual BE SAFE Ranger Floor Jacks are designed and built with safety in mind However proper training and thoughtful operation on the part of the operator can increase your overall safety DO NOT operate or repair this equipment without reading this manual and the important safety instructions shown inside Ranger 1645 Lemonwood Dr Santa Paula CA 93060 USA Tel 1 805 933 9970 Toll Free 1 800 253 2363 Fax 1 805 933 9160 www rangerproducts com WARRANTY POLICY Ranger Products are backed by over 35 years of manufacturing experience Every Floor Jack bearing the Ranger name is
5. e jack stands are positioned open the release valve VERY SLOWLY by twisting the Handle counter clockwise Lower the load to rest on the jack stands Then make sure that the release valve on the jack is closed tightly twist the Handle clockwise 2 To lower load Re check to make sure release valve is tightly closed twist the Handle clockwise Then operate the jack handle until the load is raised enough to remove the jack A DANGER DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR REMOVING THE JACK STANDS Once jack stands are removed open release valve very slowly to lower the vehicle twist the Handle counter clockwise Lower jack completely so that the vehicle is securely resting on the ground and that jack no longer makes contact with vehicle A CAUTION Keep hands or feet away from the hinge mechanism of the jack MAINTENANCE When adding or replacing hydraulic fluid always use a quality hydraulic fluid DO NOT use brake fluid alcohol detergent motor oil dirty oil or any fluid other than quality hydraulic fluid Improper fluids can cause internal damage to the jack and improper or unsafe operation ADDING HYDRAULIC FLUID With the saddle fully lowered and the jack on level ground remove the filler screw Hydraulic fluid should be filled to the level of the filler screw hole If the level is below this hole add hydraulic fluid as needed LUBRICATION All moving joints require lubrication often Lightly
6. grease saddle post and saddle bottom Remove handle and grease the lower end of handle where it rotates in the handle socket Using a grease gun grease the lift arm pivot shaft grease fitting until grease appears at the end of the shaft Oil all lift arm linkages front wheels and rear casters TROUBLESHOOTING PROBLEM 1 Unit will not lift load Purge air from hydraulic system by following procedure un der OPERATING INSTRUCTIONS 2 Unit will not sustain load or feels spongy under load Purge air from hydraulic system as above 4 Unit will not lower completely Check oil level Make sure not overfilled 5 Handle tends to raise up while the unit is under load Pump the handle rapidly several times to push oil past ball valves in power unit 6 Unit still does not operate Contact Parts amp Warranty Department SPECIFICATIONS 3 Unit will not lift to full height Purge air from hydraulic system as above Check to be sure oil level is not too high or low 46 1168mm 2 5 63 5mm 2 25 57mm 14 75 375mm Drawing Not To Scale 3 000 Ibs 1 361 kg 24 610mm 2 15 70mm 6 5 165mm 34 864mm 112 lbs 51kg 39 x 17 x 8 980mm x 425mm x 195mm 4 g PARTS BREAKDOWN CN Wo amp 0 l on qj c0 SN o a OO Wo cN Ct gt PARTS BREAKDOWN E stopper bar for canular amp l Ls mam Tt 18 rear caster bump
7. iability for damages incurred directly or indirectly as a result of any errors omissions or discrepancies Information and specifications subject to change without notice A WARNING THIS OPERATING MANUAL CONTAINS IMPORTANT DETAILS CONCERNING THE SAFE OPERATION OF THIS TOOL THE USER MUST READ AND UNDERSTAND THESE DETAILS BEFORE ANY USE OF THE TOOL THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE OWNER OPERATOR RESPONSIBILITY The owner and or operator shall study the product instructions and retain them for future reference The owner and or operator shall have an understanding of the product operating instructions and warnings before operating the jack Warning information shall be emphasized and understood If the operator is not fluent in English the product instructions and warnings shall be read to and discussed with the operator in the operator s native language by the purchaser owner or his designee making sure that the operator comprehends its contents A CAUTION INSPECTION Visual inspection should be made before each use of the jack This inspection should check for abnormal conditions such as cracked welds leaks and damaged loose or missing parts Any jack that appears to be damaged in any way is found to be worn or operated abnormally must be removed from service immediately Any jack that operates abnormally shall be removed from service until repaired by a qualified repair service center
8. rice SHIPPING DAMAGE If any damage is found notify your carrier immediately and save all packaging materials for the carrier s inspector to examine Failure to promptly report damage could result in denial of your claim A trucking company s procedure for handling damage is as follows 1 Immediately send out an inspector An inspection report is filled out on the spot a copy of which is given to the customer 2 The customer has to call the carrier to request a claim form 3 The customer mails in the claim form 4 The claim usually takes two 2 months to process If a unit is seriously damaged your Ranger Products dealer may be able to intervene requesting that the damaged unit be returned and a new unit delivered A CAUTION IMPORTANT SAFETY TIPS ALWAYS MAINTAIN A CLEAN WORK AREA KEEP VISITORS AND ESPECIALLY CHILDREN AWAY FROM WORK AREA THIS FLOOR JACK IS TO BE OPERATED BY PROPERLY TRAINED PERSONNEL ONLY OPERATION BY UNTRAINED PERSONNEL MAY RESULT IN INJURY AND OR PROPERTY DAMAGE For Parts Or Service Contact BendPak Inc Ranger Products 1645 Lemonwood Dr Santa Paula CA 93060 Tel 1 805 933 9970 Toll Free 1 800 253 2363 Fax 1 805 933 9160 www bendpak com www rangerproducts com IMPORTANT NOTE Although every effort has been taken to ensure the accuracy of this document some information may contain technical inaccuracies or typographical errors BendPak Ranger assumes no responsibility or l
9. sold with the following warranty Each Ranger Product is warranted to be free from defects in workmanship and material for a period of one year from the date of shipment provided that a written claim for such defect is made within that time This warranty does not cover damage or defects caused by carelessness of the operator misuse abuse or abnormal use which in any way impairs the proper functioning of the equipment or by the use or addition of parts not manufactured by Ranger Products or its suppliers THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE If your Ranger Products machine is not functioning properly call your Ranger Products dealer immediately On some occasions an independent contractor may be hired to do the repairs Within the warranty period a customer should not hire his own contractor unless it is authorized in writing by Ranger Products If itis necessary to return equipment for repairs your dealer will so advise you When returning equipment for repairs see that machines are properly crated and protected and prepay transportation Defective parts replaced at no charge must be returned to your dealer or Ranger Products within 60 days of the date that the replacement parts are shipped otherwise you must pay for the replacement parts at the current selling p
Download Pdf Manuals
Related Search