Home

2002 Nissan Quest Owners Manual

1. Child safety locking helps prevent doors from being opened accidentally especially when small children are in the vehicle Pre driving checks and adjustments 3 5 REMOTE KEYLESS ENTRY SYSTEM It is possible to lock unlock all doors turn the interior lights on or off and activate the panic alarm by using the keyfob from out side the vehicle Be sure to remove the key from the vehicle before locking the doors and leaving it The keyfob can operate at a distance of approximately 30 ft 10 m from the vehicle The effective distance depends on the con ditions around the vehicle As many as four keyfobs can be used with one vehicle For more information concern ing the purchase and use of additional key fobs contact an authorized NISSAN dealer CAUTION Listed below are conditions or occur rences which will damage the keyfob e Do not allow the keyfob to become wet e Do not drop the keyfob e Do not strike the keyfob sharply against another object 3 6 Pre driving checks and adjustments e Do not place the keyfob for an ex tended period in an area where tem peratures exceed 140 F 60 C HOW TO USE REMOTE KEY LESS ENTRY SYSTEM Locking doors 1 Close all doors 2 Push the button on the keyfob 3 All doors lock 4 The parking lights flash twice and the horn chirps once to verify all doors are locked Unlocking doors For memory seat and mi
2. Wheel dollies Wheel lift tow truck ACE1029 TOWING RECOMMENDED BY ground or place the vehicle on a flat bed NISSAN truck as illustrated NISSAN recommends that your vehicle be towed with the driving front wheels off the In case of emergency 6 13 6 14 CAUTION e Never tow automatic transmission models with the front wheels on the ground or four wheels on the ground forward or backward as this may cause serious and expensive dam age to the transmission If it is nec essary to tow the vehicle with the rear wheels raised always use tow ing dollies under the front wheels When towing with the front wheels on towing dollies e Turn the ignition key to the OFF position and secure the steer ing wheel in a straight ahead position with a rope or similar device Never secure the steer ing wheel by turning the igni tion key to the LOCK position This may damage the steering lock mechanism e Move the shift lever to the N Neutral position In case of emergency When towing with the rear wheels on the ground if you do not use towing dollies Always release the parking brake Never use a tow bar that attaches to the bumper when you tow your ve hicle It may damage the bumper and cause damage to the transmission Do not tow with a sling type truck either from the front or rear It may cause body damage Never utilize the rear tie down brack ets o
3. Parcel shelf floor storage position APD1071 PARCEL SHELF if so equipped amp WARNING e Before using the parcel shelf the three passenger bench seat must be 2 28 Instruments and controls in the third row position and the seat back must be upright e After adjusting the parcel shelf to the desired height make sure the lock knob is securely latched Properly secure all packages under the parcel shelf net to prevent them from sliding or shifting Do not place packages higher than the three passenger bench seat back In a sudden stop or collision unsecured packages could cause personal in jury Be sure to secure all three parcel shelf net loops onto the retainers located on the bottom side of the parcel shelf The packages placed on the parcel shelf and restrained by the parcel shelf net must not exceed 30 pounds 13 6 kg or the parcel shelf may not remain secure Do not allow people or pets on or under the parcel shelf The parcel shelf must be removed from the vehicle if installing a child restraint on the three passenger bench seat that requires the use of a top tether strap that is anchored to the vehicle floor Failure to remove the parcel shelf can increase the severity of injury to the child in an accident The parcel shelf allows for additional stor age for packages Do not load more than 30 pounds 13 6 kg on the parcel shelf The parcel shelf can be installed at
4. APD1073 Put the parcel shelf in the floor storage position when the parcel shelf is not used or required Instruments and controls 2 29 Luggage rack LUGGAGE RACK Always distribute the luggage evenly on the luggage rack Do not load more than 100 pounds 45 kg Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating GVWR or its Gross Axle Weight Rating GAWR front and rear The GVWR and GAWR are located on the Safety Com pliance Certification Label located on the driver s door pillar For more information regarding GVWR and GAWR refer to Technical and Consumer Information The front and rear cross bars can be adjusted forward and backward Place your luggage 2 30 Instruments and controls Adjustable cross bars APD1072 between the bars adjust the bars and secure the luggage with rope to the bars Always check the tightness of the adjusting knobs There are also adjustable loops on the side bars for the rope attachment CAUTION Use care when placing or removing items from the luggage rack If you cannot comfortably lift the items onto the luggage rack from the ground use a ladder or stool WINDOWS POWER WINDOWS A WARNING e Make sure that all passengers have their hands etc inside the vehicle before closing the windows Use the window lock switch to prevent unex pected use of the power windows e Do not leave chi
5. oF VF a Air not passed through heater core Ecm Rear seat A C fan control Air conditioner button A C Rear seat A C Air flow Temp Fan switch fan control control control control OFF MAX automatically REAR A C A C Teei 4 turns on ces REAR SEAT A C FAN CONTROLS SES lt Air not passed through heater core Fan control dial 2nd row ventilators Fan control WHA0014 4 10 Heater air conditioner and audio systems HEATER AND AIR CONDITIONER automatic if so equipped Digital Air flow control display buttons MAX A C button cme aap Sef El D GH 6 a OFF ra n O O Temperature Rear seat fan control Fan speed control button if so equipped dial amp WARNING e The air conditioner cooling function operates only when the engine is running e Do not leave children impaired adults or pets alone in your vehicle On hot sunny days temperatures in a closed vehicle could quickly be come high enough to cause severe or possibly fatal injuries to people or animals e Do not use the recirculation mode for long periods as it may cause the WHAOO15 interior air to become stale and the windows to fog up e Positioning of the heater and air con ditioner co
6. Engine oil viscosity 10 4 OUTSIDE MINONS sssrinin anr 3 14 Overdrive SWIC hiscere asnes 5 8 Overheat If your vehicle overheats s 6 10 Owner s manual service manual order NOMAI Mize esera e EEE 9 23 P Parcel Shelf eraris aa 2 28 Parking Parking brake CheCK ssssseeseesees 8 21 Parking brake operation ssessenscssen 5 9 Parking parking on hills 5 13 Personal reading light 2 34 Power Power door locks cc scceeeeeeeeee 3 2 3 4 Power steering fluid 0008 8 13 9 2 Power support front Seat 1 4 Power vent windows si Power WINKOWS ccccccceesteeeeeeeeeseeee Precautions Maintenance precautions ee 8 5 Precautions on seat belt usage 1 39 Precautions when starting and driving 5 2 PUSH StAMiNG neies aae aaan 6 10 R Radio Car phone or CB radiOisirsirsissisnns 4 46 FM AM radio with cassette player 4 20 FM AM radio with cassette player and compact disc CD player 4 26 Readiness for inspection maintenance UM t Stiswctc tai anvara ciate 9 21 Rear O00 iis3 cena eines 3 10 Rear door lOck insmeren 3 10 Rear power socket sssssesssrrresrerresrerrsssse 2 22 Rear seat air conditioner 4 14 Rear window defogger switch 00 2 16 Rear window wiper and washer SWINE Sasiia elie 2 16 Refrigerant recommendation cce 9 6 Registering your vehicle in another CONYE E seetierise 9 10 Remote keyless entry system sssr 3 6
7. measure measure Liter 16 5 8 Unleaded gasoline with an octane rating of Fuel 20 gal gal 75 7 atleast 87 AKI RON 91 1 Engine oil 7 Drain and refill F me E e API Certification Mark 2 3 With oil filter change tdt 3 3 8 at 38 e API grade SG SH Energy Conserving amp Il or mom API grade SJ Energy Conserving 2 3 Without oil filter change 3 7 8 qt 3 1 8 qt 3 6 e ILSAC grade GF I amp GF I 2 3 Cooling system With reservoir tank 11 1 4 gt 93 8 qt 10 6 50 Genuine NISSAN Anti freeze Coolant or equivalent Reservoir 1 1 8 qt 1qt 1 1 50 Demineralized water or Distilled water NISSAN matic D Continental U S and Automatic transaxle fluid 10 qt 8 1 4 qt 9 4 Alaska or Canada NISSAN Automatic Power steering fluid Brake fluid Refill to the proper oil level according to the instructions in the Do it yourself section Transmission Fluid 4 Type F automatic transmission fluid or equivalent Genuine NISSAN Brake Fluid 5 or equivalent DOT 3 US FMVSS No 116 Multi purpose grease Air conditioning system refrig erant 1 For further details see Fuel recommendation 2 3 4 NLGI No 2 Lithium soap base HFC 134a R 134a 6 For further detail see Engine oil and oil filter recomendations For further details see Recommended SAE engine oil viscosity Dexron IIl Mercon or equivalent may also be used Outside the Continental United States and Al
8. s VOLUME MEDIA MEM lt SEEK gt nee MT Coc ve On iS Y Speaker control H hone jack button eadphone jacks AHA1060 Volume e Media select AM FM tape CD CD changer e Speakers ON OFF REAR AUDIO CONTROLS if so equipped Radio features controlled by the rear seat remote control if so equipped are listed below e Mem proceed to the next preset station AM FM Seek lt gt Push the Memory three and Memory five buttons on the front radio controls simulta neously to turn the rear controls on Push them again to turn the rear audio controls off The headphones symbol illuminates in the front display when the rear audio controls are on Two headphone jacks are provided so two rear seat passengers may listen to the audio system privately The rear volume controls can only increase the volume to the level at which the front radio volume control is set Headphones are not included with the ve hicle Most portable radio headphones work with the rear audio controls For vehicles equipped with the premium FM AM radio with cassette player compact disc player and 6 disc CD player if the rear passengers turn off the rear speakers and are using headphones they may choose to listen to a different media than the front passengers The rear passengers can listen to the radio while the front passengers can listen to the same thing
9. AIC1075 The cigarette lighter element is an acces sory A genuine NISSAN cigarette lighter or equivalent can be purchased from an autho rized NISSAN dealer The cigarette lighter operates when the ignition switch is in the ACC or ON position Push the lighter in all the way When the lighter is heated it springs out Return the lighter to its original position after use The utility tray has a rubber mat that may be removed for cleaning The ashtray is an accessory A genuine NISSAN ashtray or equivalent can be pur chased from an authorized NISSAN dealer The ashtray fits in the utility box Do not use the utility box as an ashtray Use only a genuine NISSAN ashtray or equivalent Pull on the lid of the ashtray to remove it for disposing of ashes CAUTION The cigarette lighter socket is a power source for the cigarette lighter element only The use of the cigarette lighter socket as a power source for any other accessory is not recommended A WARNING The cigarette lighter should not be used while driving so full attention may be given to vehicle operation Instruments and controls 2 23 STORAGE oesi Map pocket AIC1078 MAP POCKETS A map pocket is located on the right hand side of the instrument panel and on the back of the passenger seat The map pocket can be used to store maps 2 24 Instruments and controls ARS1249 PU
10. c You notice a change in the sound of the exhaust system d You have had an accident involv ing damage to the exhaust system underbody or rear of the vehicle THREE WAY CATALYST The three way catalyst is an emission con trol device installed in the exhaust system Exhaust gases in the three way catalyst are burned at high temperatures to help reduce pollutants A WARNING e The exhaust gas and the exhaust system are very hot Keep people animals or flammable materials away from the exhaust system com ponents e Do not stop or park the vehicle over flammable materials such as dry grass waste paper or rags They may ignite and cause a fire CAUTION e Do not use leaded gasoline Depos its from leaded gasoline seriously reduce the three way catalyst s abil ity to help reduce exhaust pollut ants Keep your engine tuned up Malfunc tions in the ignition fuel injection or electrical systems can cause over rich fuel flow into the three way cata lyst causing it to overheat Do not keep driving if the engine misfires or if noticeable loss of performance or other unusual operating condi tions are detected Have the vehicle inspected prompily by an authorized NISSAN dealer Avoid driving with an extremely low fuel level Running out of fuel could cause the engine to misfire damag ing the three way catalyst Do not race the engine while warm ing it up Do not push or tow your vehicle to sta
11. 5 Check under the vehicle again for leaking fuel If you see or smell fuel do not start your vehicle again If no fuel is detected try to start your vehicle again amp WARNING If you see or smell fuel do not reset the switch or try to start your vehicle You could injure yourself or others Have all the passengers get out of the vehicle and call the local fire department or a towing service 6 12 In case of emergency TOWING YOUR VEHICLE When towing your vehicle all State Provin cial in Canada and local regulations for towing must be followed Incorrect towing equipment could damage your vehicle Towing instructions are available from an authorized NISSAN dealer Local service operators are generally familiar with the applicable laws and procedures for towing To assure proper towing and to prevent accidental damage to your vehicle NISSAN recommends having a service operator tow your vehicle It is advisable to have the service operator carefully read the following precautions A WARNING e Never ride in a vehicle that is being towed e Never get under your vehicle after it has been lifted by a tow truck CAUTION e When towing make sure that the transmission axles steering system and powertrain are in working con dition If any unit is damaged dollies must be used e Always attach safety chains before towing
12. 8 7 Engine Cooling SYSteM ce eeceeeeseeeenteeeeneeereneees 8 8 Checking engine coolant level s s s 8 8 Changing engine Coolant eceeeeeeeeeeees 8 9 Engine Oil siro siriasi naaien 8 9 Checking engine oil level eeeeeeeeeeeeeees 8 9 Changing engine oil 00 eeeeeeeeeeeeeeeeeteeeees 8 10 Changing engine oil filter ee eects 8 11 Automatic transmission fluid 0 0 0 eeeeeeeeee 8 12 Temperature conditions for checking 8 12 Power steering fluid cc ccceseeeeseeeeeeeeeeeeseees 8 13 Brake WIG sone cceceectcs deceectsnectescecenesecensentenesensentedee 8 13 Window washer fluid 0 0 eee eeeeeeeeneeeeneeereneeees 8 14 Battery ve scsecdededilcedicderclectandgl one a aaa aE EaR 8 14 Jump starting aineeton 8 15 Drive IDGIS s25 i5 cecssccecvccczstetsietasctedesetassaeth wichinetiens 8 16 Spark pllGS rt n er ieee he oa 8 16 Replacing spark PIUQS eeeeeeeeeeeeeeneeeeeee 8 16 Alt CIGANGT eiaeiiai tnaa iiai 8 17 Windshield wiper blades eicseceeeeeeeee 8 19 CIS NING sssini aoi ina 8 19 Replacing aanraai 8 19 Parking brake and brake pedal eee 8 21 Checking parking brake 8 21 Checking brake pedal eeceeeeeeteeeteeeeee 8 21 Brake DOOSIGM s ssecevezcetsecesaseetetsccees tacteececesticnense 8 22 FUSS tiseh cases cncne dice echsvn aeri iiaa E 8 22 Engine Compartment eeeeeseeeeeeeeeeneeeeeee 8 22 Passenger compartment ssec 8 23 Keyfob ba
13. Balance control allows you to adjust the sound distribution between the right and left speakers Push the BAL button and the setting indica tor bar appears in the display window Press the SELECT button amp to shift the sound to the right speakers The single indicator bar moves to the right of the display win dow Press the SELECT button W to shift the sound to the left speakers The single indicator bar moves to the left of the display window When the indicator bar is in the center position the sound is equally distrib uted between the right and left speakers Following balance adjustment the display window shows the current setting for three seconds then returns to the display prior to adjustment Fader Fader control allows you to adjust sound distribution between the front and rear speakers Push the FADE button and the setting indi cator bar appears in the display window Press the SELECT button A to shift the sound to the front speakers The single indicator bar moves to the right of the dis play window Press the SELECT button WY to shift the sound to the rear speakers The single indicator bar moves to the left of the display window When the indicator bar is in the center position the sound is equally distributed between the front and rear speakers Following fader adjustment the display win dow shows the current setting for three seconds then returns to the display prior to adjustment COMP butt
14. Jacking up the vehicle and remov ing the damaged tire A WARNING e Never get under the vehicle while it is supported only by the jack e Use only the jack provided with your vehicle to lift the vehicle Do not use the jack provided with your vehicle on other vehicles The jack is de signed for lifting only your vehicle during a tire change e Use the correct jack up points Never use any other part of the ve hicle for jack support e Never jack up the vehicle more than necessary e Never use blocks on or under the jack e Do not start or run engine while vehicle is on the jack It may cause the vehicle to move e Do not allow passengers to stay in the vehicle while it is on the jack e Never run the engine with the wheels off of the ground It may cause the vehicle to move Carefully read the caution label attached to the jack body and the following in structions 1 Loosen each wheel nut one or two turns by turning counterclockwise with the lug wrench Do not remove the wheel nuts until the tire is off the ground In case of emergency 6 5 2 Place the jack directly under the jack up point as illustrated above so the top of the jack contacts the vehicle at the jack up point Align the center of both the jack head and the notch at the jack up point as shown Also fit the notched portion of the vehicle in the groove of the jack head as shown The jack should be used on level firm ground 3 Carefu
15. Supplemental air bag warning light Seat belso criei aaeain aa eaa as EEE aaa Precautions on seat belt usage eee Child safeties s Pregnant WOMEN sascha 1 42 Injured POISONS ss sriiriciriiesiierniresnisriisns 1 42 Three point type seat belt with retractor 1 42 Three point type seat belt with retractor for second row bucket seats ecne 1 45 Three passenger bench seat in the second TOW POSITION csaccccecscsecssssevtiacoesae canescees 1 49 Three passenger bench Seat 1 50 Two point type seat belt without retractor center of rear seat 1 51 Seat belt extenders 0 0 0 eeeeeeeeeeseeteeeeeeeee 1 53 Seat belt maintenance 0 00 eeeeeeeeeeeeeeeeee 1 54 Child restraints cccccceceeceeeseeeeesseeeeseeeeeeneeeeees 1 54 Precautions on child restraints 0 ee 1 54 Installation on three passenger bench seat Center position cceeseeeeceeesereeeeeees 1 56 Installation on second and third row outboard POSITIONS 0 0 eee eee eee etteneeeeeeees 1 59 Installation on front passenger seat 1 64 LATCH Lower Anchors and Tether for Children system ccccceceeeseeeeeeeeeeseeeeeeeneeeeees 1 67 Child restraint with top tether strap 1 68 Installation on second row bench or Installation on three passenger bench DUCKCH SCAU tess scaceecices cect evchenvengeresscctenecuereeeatews 1 69 seat I TAM TOW ssnin anaa 1 72 Installation on three passenger bench Inte
16. Three passenger bench seat INSERT IOS hs fasten Oy unfasten WRSOO15 2 Slowly pull the seat belt out of the retrac tor and insert the tongue into the buckle until you hear and feel the latch engage Three passenger bench seat in second row position Shoulder belt retainer WRS0052 3 Position the passenger side shoulder belt in the shoulder belt retainer Seats restraints and supplemental air bag systems 1 49 Three passenger bench seat TAKE UP slack WRS0053 POSITION low on the hips 4 Position the lap belt portion low and snug on the hips as shown 5 Pull the shoulder belt portion toward the retractor to take up extra slack Three passenger bench seat INSERT IOS hs fasten oy K unfasten 1 50 Seats restraints and supplemental air bag systems WRS0015 THREE PASSENGER BENCH SEAT Fastening the seat belts 1 Adjust the seat A WARNING e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries e For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly Third row passeng
17. To clean the seat belt webbings apply a mild soap solution or any solution rec ommended for cleaning upholstery or carpet Then wipe with a cloth and allow the seat belts to dry in the shade Do not allow the seat belts to retract until they are completely dry If dirt builds up in the shoulder belt guide of the seat belt anchors the seat belts may retract slowly Wipe the shoul der belt guide with a clean dry cloth e Periodically check to see that the seat belt and the metal components such as buckles tongues retractors flexible wires and anchors work properly If loose parts deterioration cuts or other dam age on the webbing is found the entire seat belt assembly should be replaced 1 54 Seats restraints and supplemental air bag systems CHILD RESTRAINTS PRECAUTIONS ON CHILD RE STRAINTS amp WARNING Infants and small children should al ways be placed in an appropriate child restraint system while riding in the vehicle Failure to use a child restraint can result in serious injury or death Infants and small children should never be carried on your lap It is not possible for even the strongest adult to resist the forces of a severe accident The child could be crushed between the adult and parts of the vehicle Also do not put the same seat belt around both your child and yourself Never install a rear facing child re straint in the front seat An inflating air bag could seriously injure or kill yo
18. Objects viewed in the outside mirror on the passenger side are closer than they appear Be careful when moving to the right Using only this mirror could cause an accident Use the inside mir ror or glance over your shoulder to properly judge distances to other ob jects Heated mirrors Canada only The electric control type outside mirrors can be heated to defrost defog or de ice for improved visibility Press the rear window defogger switch to activate the heating func tion Press the switch again to deactivate or the heating function will automatically turn off after approximately 15 minutes 3 14 Pre driving checks and adjustments M008 Foldable outside mirrors Push the outside mirrors backward to fold them 4 Heater air conditioner and audio systems Ventilators mionntan nae ieee O 4 2 FM AM radio with cassette player 4 20 Center Ventilators eceeceeeeeeeeeeeeeteeeeneeeneees 4 2 FM AM radio with cassette player and Side ventilator S isse 4 2 compact disc CD playel eeeeeeeeeee 4 26 Heater and air conditioner manual ee 4 3 Compact disc CD player if so COMMONS iaeiae enina iene 4 3 QUIPPOG siscstasccencviescsanednescnciesstdasubeetedeneybecees 4 32 Heater operatio Minione 4 4 CD care and Cleaning cseceeeeeeeeereeeeees 4 33 Air conditioner operation cee 4 5 Steering wheel switch for audio controls Alm TloW Chants oinin n 4 7 if So
19. Page 1 69 Installation on second row bench or bucket seat Two passenger bench seat Second row outboard seating positions Anchor bracket on back of second row bench seat Page 1 69 Installation on second row bench or bucket seat Two passenger bench seat with integrated child safety seat Second row driver side seating position Anchor bracket on back of second row bench seat Page 1 69 Installation on second row bench or bucket seat Two passenger bench seat with integrated child safety seat Second row passen ger side seating posi tion CANNOT BE TETHERED Three passenger bench seat Second row passenger driver side outboard seating posi tion or center seating position Anchor bracket on back of the three pas senger bench seat Page 1 72 Installation on three passenger bench seat in second row Three passenger bench seat Third row passenger driver side outboard or center seating position Anchor bracket on back of the three pas senger bench seat Page 1 72 Installation on three passenger bench seat in third row INSTALLATION ON SECOND ROW BENCH OR BUCKET SEAT A child restraint with a top tether strap may be placed on the second row bench or bucket seats Once the child restraint is properly secured to the seat see Installa tion on second and third row outboard posi tions Front facing earlier in this section follow the directio
20. Supplemental front air bag system The driver supplemental air bag is located in the center of the steering wheel The front passenger supplemental air bag is mounted in the dashboard above the glove box These systems are designed to meet optional certification requirements under U S regula tions They are also permitted in Canada The optional certification allows front air bags to be designed to inflate somewhat less force fully than previously However all of the information cautions and warnings in this manual still apply and must be followed Supplemental front air bag modules Diagnostic sensor unit gh Seat belt pre tensioner retractor g Seat belt pre tensioner retractor WRS0075 The supplemental front air bag system is designed to inflate in higher severity frontal collisions although it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact It may not inflate in certain frontal collisions Vehicle damage or lack of it is not always an indica tion of proper supplemental air bag system operation When the supplemental front air bag in flates a fairly loud noise may be heard followed by the release of smoke This smoke is not harmful and does not indicate a fire Care should be taken to not intention 1 34 Seats restraints and supplemental air bag systems ally inhale it as it may cause irritation and choking Those with a history of a br
21. The single indicator bar moves to the left of the display window When the indicator bar is in the center position the sound is equally distributed between the front and rear speakers Following fader adjustment the display win dow shows the current setting for three seconds then returns to the display prior to adjustment COMP button Press this button to activate the compres sion function This reduces the dynamic range which provides the listener with a more consistent level of volume The dis play window shows COMP when the COMP button is pushed Clock operation The clock is on in the display regardless of what mode media or function the radio is in as long as the ignition is in ACC or ON Clock set Press the RDS CLK button until SELECT HOURS is displayed then use the SEL lt P buttons to change the hour press the RDS CLK button again until SELECT MINS is displayed then use the SEL lt P buttons to change the minutes The display will return to the previous radio station tape or CD that was being played previous to setting the clock in 7 seconds or you may press the RDS CLK button until the previous display appears Selecting the desired band Push the AM buttons to change to AM band or push the FM button to change to FM1 or FM2 band reception The FM stereo indicator ST illuminates during FM stereo reception When the ste reo broadcast signal is weak the radio automatically changes from stereo to mo
22. e GVWR Gross Vehicle Weight Rating maximum total weight load limit speci fied for the vehicle e GAWR Gross Axle Weight Rating maximum weight load limit specified for the front or rear axle e Gross combined weight GVW plus the total weight of the trailer and all its cargo DETERMINING VEHICLE LOAD CAPACITY The load capacity of this vehicle is deter mined by weight not by available cargo space For example a luggage rack bike carrier cartop carrier or similar equipment does not increase load carrying capacity of your vehicle To determine vehicle load capacity Vehicle weight can be determined by using a commercial grade scale found at places such as a truck stop gravel quarry grain elevator or a scrap metal recycling facility 1 Determine the curb weight of your vehicle 2 Compare the curb weight amount to the GVWR specified for your vehicle to de termine how much more weight your vehicle can carry 3 After loading cargo amp passengers re weigh your vehicle to determine if either GVWR or GAWR for your vehicle is exceeded If GVWR is exceeded re move cargo as necessary If either the front or rear GAWR is exceeded shift the load or remove cargo as necessary LOADING TIPS e The GVW must not exceed GVWR or GAWR specified on the F M V S S Cer tification Label e Do not load the front and rear axle to the GAWR Doing so will exceed the GVWR A WARNING e Properly secure
23. the instrument panel registers The J indicator light comes on and the display window shows the set temperature The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle However the air is not cooled regardless of the temperature setting unless the A C button is selected gt o VA Push this button to get air from the front and rear floor outlets and instrument panel ven tilators at the same time The lt indicator light comes on and the display window shows the set temperature The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle However the air is not cooled re gardless of the temperature setting unless the A C button is selected e A Push this button to direct airflow to the front and rear floor outlets The y indicator light comes on and the display window shows the set temperature The EATC heats the air if the selected temperature is warmer than the outside air coming into the vehicle However the air is not cooled re gardless of the temperature setting unless the A C button is selected MAX Push the MAX button to choose air recircu lation In this mode the EATC system recir culates the air inside the vehicle rather than drawing air from outside Air is distributed through the instrument panel ventilators similar to w mode Use this mode to rap idly cool the insi
24. toms are encountered have your vehicle checked at an authorized NISSAN dealer or other competent service facility However now and then you may notice light spark knock for a short time while accelerating or driving up hills This is no cause for concern because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load 9 4 Technical and consumer information API certification mark API service symbol ATI0507 ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the correct quality and viscosity to ensure sat isfactory engine life and performance NISSAN recommends the use of a low friction oil energy conserving oil in order to improve fuel economy and conserve en ergy Oils which do not have the specified quality label should not be used as they could cause engine damage Only those engine oils with the American Petroleum Institute API CERTIFICATION MARK on the front of the container should be used This type of oil supersedes the existing API SG SH or SJ and Energy Conserving II categories If you cannot find engine oil with the API CERTIFICATION MARK use an API grade SG SH Energy Conserving II or API grade SJ Energy Conserving oil An oil with a single designation SG or SH or in combi nation with other categories for example SG CC or SG CD may also be used if one with the API CERTIF
25. Positions NYA VA 1 Second Row Seating Position ARS1196 Proper usage is important to your safety A WARNING Do not slide the seat while the ve hicle is moving After adjustment gently rock in the seat to make sure it is securely locked After sliding the seat check that both sides of the seat are locked securely by attempting to move each side of the seat forward and backward This must be done before the vehicle is put into motion in order to prevent unintended movement of the seat and passenger injuries Do not allow passengers to use seats placed in storage positions for the seat belts will not protect the occupants Be sure to use the proper seat belts for each seat location Improper seat belt usage will in crease the risk of severe injury in an accident When the vehicle is being used to carry cargo properly secure all cargo to help prevent it from sliding or shift ing Do not place cargo higher than the seatbacks In a sudden stop or collision unsecured cargo could cause personal injury Be careful not to damage the seat belt Never allow anyone to ride in the cargo area or on a seat that is in a storage position It is not designed for passengers They could be in jured in sudden braking or a collision To prevent luggage or packages from sliding forward during braking do not stack anything in the cargo area higher than the seatbacks It is extremely dangerous to ride i
26. Pushing the reset button for more than 1 second resets the trip odometer to zero mtg 4 L 3 5 j A 2 RPM x 1000 6 S i RUN S My a Red 7 T zone c aA p 84 DO NOT REV engine into red zone WIC0079 TACHOMETER The tachometer indicates engine speed in revolutions per minute RPM amp CAUTION When engine speed approaches the red zone shift to a higher gear Oper ating the engine in the red zone may cause serious engine damage Instruments and controls 2 5 WICO080 ENGINE COOLANT TEMPERATURE GAUGE This gauge indicates the engine coolant temperature The engine coolant tempera ture varies with the outside air temperature and driving conditions CAUTION If the gauge indicates engine coolant temperature above the normal range stop the vehicle as soon as safely pos sible If the engine is overheated con tinued operation of the vehicle may 2 6 Instruments and controls seriously damage the engine See the In case of emergency section for immediate action required WICO0081 FUEL GAUGE This gauge indicates the approximate fuel level in the tank The gauge may move slightly during brak ing turning acceleration or going up or down hills The gauge needle remains in approximately the same position even when the ignition key is turned OFF The low fuel warning light comes on when the amount of fuel in
27. Seats restraints and supplemental air bag systems 1 55 e For a front facing child restraint if the seat position where it is installed has a three point type lap shoulder belt check to make sure the shoul der belt does not go in front of the child s face or neck If it does put the shoulder belt behind the child restraint If you must install a front facing child restraint in the front seat see Installation on front pas senger seat later in this section e When your child restraint is not in use keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident amp CAUTION Remember that a child restraint left in a closed vehicle can become very hot Check the seating surface and buckles before placing your child in the child restraint Front facing WRS0054 INSTALLATION ON THREE PASSENGER BENCH SEAT CENTER POSITION Front facing When you install a child restraint in a rear center seat follow these steps 1 Position the child restraint on the seat as illustrated Always follow the restraint manufacturer s instructions 1 56 Seats restraints and supplemental air bag systems Front facing INSERT ne 4 fasten 5 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt
28. These seating arrangements provide less leg room for third row passengers but more cargo room Seven passenger driving arrangement with third seat in seating position 3 More cargo room ARS1204 Third seat folded down APDO0042 The fold down tabletop seats in the second and third rows provide a surface for eating or playing games on long trips Seats restraints and supplemental air bag systems 1 21 Third seat folded up in storage position 2 APDO0043 If a considerable amount of cargo area is needed the seat cushion of the three passenger sliding bench seat can be flipped up and the seat can be moved up to storage position 2 just behind the second row seat Third seat folded up in storage position 1 second seat removed APDO0049 When maximum cargo area is needed and there are no rear seat passengers the second row seat can be removed and the three passenger sliding bench seat can be moved up to storage position 1 just behind the front seats 1 22 Seats restraints and supplemental air bag systems Second row seat folded down The second row bench seat can be folded down to serve as a tabletop for passengers sitting in the three passenger bench seat Second and third row seats folded down APDO0045 The second and third row bench seats can be folded down to tabletops Third seat in second position with second row seat
29. To avoid or reduce the risk the procedures must be followed precisely amp CAUTION This is used to indicate the presence of a hazard that could cause minor or moderate personal injury or damage to your vehicle To avoid or reduce the risk the procedures must be followed carefully APD1005 If you see this symbol it means Do not do this or Do not let this happen The inside pages of this manual contain a minimum of 50 recycled fibers including 10 post consumer fibers CALIFORNIA PROPOSITION 65 WARNING amp WARNING Engine Exhaust some of its constitu ents and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm 2001 NISSAN NORTH AMERICA INC GARDENA CALIFORNIA All rights reserved No part of this Owner s Manual may be reproduced or stored in a retrieval system or transmitted in any form or by any means electronic mechanical photo copying recording or otherwise without the prior written permission of Nissan North America Inc Gardena California Welcome To The World Of NISSAN NISSAN TECHNICAL CENTER NORTH AMERICA INC in Farmington Hills Michigan NISSAN MANUFACTURING FACILITY in Smyrna Tennessee WFW0002 Your new NISSAN is the result of our dedication to produce the finest in safe reliable and eco nomical transportation Your vehi
30. forward The seatback moves forward Re lease the lever to lock the seatback in position Seats restraints and supplemental air bag systems 1 3 FRONT POWER SEAT e Do not operate the power support seat j i for a long period of time when the engine ADJUSTMENT if so equipped is off This discharges the battery A WARNING e Do not adjust the driver s seat while driving so full attention may be given to vehicle operation e Do not leave children unattended in side the vehicle They could unknow ingly activate switches or controls Unattended children could become involved in serious accidents For memory seat and mirror information see Memory driver seat and mirrors in the Pre driving checks and adjustments sec tion Operating tips e The motor has an auto reset overload protection circuit If the motor stops dur ing operation wait 30 seconds then re activate the switch 1 4 Seats restraints and supplemental air bag systems Forward and backward Recline ARS1212 Forward and backward To move the seat forward push the power slide switch forward To move the seat backward push the power slide switch backward Release the switch to stop the movement of the seat Reclining To recline the seat back push the power recliner switch backward To return to a more upright position push the power re cliner switch forward Release the switch to stop the movement of the seatback
31. if so equipped OFF OFF t Air passed through heater core Fan control 4 WHA0010 HEATING lt Air passed through heater core Fan control Temperature Airflow control dial control dial dial Air conditioner Rear seat A C fan control if so equipped button A C Roar seat AC Air flow Temp Fan switch if so equipped control control control HOT OFF OFF Y A RIGHT 4 WHAOO11 4 8 Heater air conditioner and audio systems HEATING amp DEFROSTING DEFOGGING N Fan control ia EN 4 Air passed through heater core Temperature Air flow control control dial dial Rear seat if so equi A C switch OFF A C fan control Air conditioner pped button Rear seat AC airflow Temp Fan if so equipped control control control We HOT OFF had RIGHT 4 WHA0012 COOLING a Air not passed through heater core Fan control Temperature Air flow control dial control dial dial or neon ae 1 2 3 a Bes Rear seat A C fan control Air conditioner if so equipped button Rear seat A C fan control if so equipped A C Air flow switch Temp Fan control control control MAX A C OFF automatically turns on COOL REAR A C ler i WHA0094 Heater air conditioner and audio systems 4 9 COOLING Fan control dial Temperature control dial la aL flows control
32. in severe injury or death It could also damage your vehicle Explosive hydrogen gas is always present in the vicinity of the battery Keep all sparks and flames away from the battery Do not allow battery fluid to come into contact with eyes skin clothing or painted surfaces Battery fluid is a corrosive sulfuric acid solution which can cause severe burns If the fluid should come into contact with anything immediately flush the con tacted area with water Keep the battery out of the reach of children The booster battery must be rated at 12 volts Use of an improper rated battery can damage your vehicle e Whenever working on or near a bat Vehicle being jump started tery always wear suitable eye pro if n tectors for example goggles or in l A i TEN gt dustrial safety spectacles and 7 H ON remove rings metal bands or any S fl other jewelry Do not lean over when K Q H x Zed jump starting SO gar Wi 3 Ha 2 e Do not attempt to jump start a frozen SS H battery It could explode and cause CANN sas F A Se 2 serious injury Sar gt f s p e Your vehicle has an automatic en aa xX NES YO E gine cooling fan It could come on at Cloth verele with any time Keep hands and other ob battery for booster ACE1009 jects away from it Always follow the instructions below 3 Remove vent caps on the battery if so Failure to do so could result in damage equipped Cover the battery wit
33. pedal travel 2 10 Instruments and controls e If the brake fluid level is below the MINIMUM or MIN mark on the brake fluid reservoir do not drive until the brake system has been checked at a NISSAN dealer s If the light comes on while the engine is running it may indicate the anti lock portion of the brake system is not functioning prop erly Have the system checked by an autho rized NISSAN dealer If a malfunction occurs in the system the anti lock function turns off but the brakes continue to operate normally Anti lock brake warning light If the light comes on while you are driv ing contact an authorized NISSAN dealer for repair aN Low fuel warning light This light comes on when the fuel level in the fuel tank is getting low Refuel as soon as it is convenient preferably before the fuel gauge reaches E Empty There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E Empty INDICATOR LIGHTS OD Overdrive off indicator light This light comes on during driving when the overdrive switch is pressed to prevent over drive operation 4th gear The O D OFF indicator light comes on for two seconds each time the ignition key is turned ON This shows the light is function ing properly If the O D OFF indicator light blinks for approximately 8 seconds after coming on for 2 seconds have an authorized NISSAN dealer check the transmission and
34. reaches operating temperature then turn it off Remove the oil filler cap Place a large drain pan under the drain plug Remove the drain plug with a wrench and completely drain the oil If the oil filter is to be changed remove and replace it at this time See Chang ing engine oil filter later in this section amp WARNING Be careful not to burn yourself The engine oil may be hot Prolonged and repeated contact with used engine oil may cause skin can cer Try to avoid direct skin contact with used oil If skin contact is made wash thoroughly with soap or hand cleaner as soon as possible Keep used engine oil out of reach of children Waste oil must be disposed of properly Check your local regulations 6 Clean and re install the drain plug and a new washer Securely tighten the drain plug with a wrench Drain plug tightening torque 22 to 29 ft lb 29 to 39 N m Do not use excessive force 7 Refill the engine with a recommended oil through the oil filler opening then install the oil filler cap securely See the Technical and consumer infor mation section for drain and refill capac ity The drain and refill capacity depends on the oil temperature and drain time Use these specifications for reference only Always use the dipstick to determine when the proper amount of oil is in the engine 8 Start the engine Check for leakage around the drain plug Correct as re
35. sette tape is playing to stop the tape Push the TAPE button to play the tape Changing the direction of tape play Push the SIDE 1 2 select button to switch sides on the tape The display will change from TAPE 1 PLAY to TAPE 2 PLAY FF Fast Forward REW Rewind Push the REW or FF button for the desired direction The FF or REW symbol illuminates in the display To stop the FF or REW function press the FF or REW button again or the TAPE but ton Dolby NR Noise Reduction Push the DO button for Dolby NR encoded tapes to reduce high frequency tape noise When activated a DO appears in the dis play window Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora tion Dolby NR and the double D symbol are trademarks of Dolby Laboratories Li censing Corporation AMS Automatic Music Search Pushing the seek button while playing a cassette tape activates the Automatic Music Search AMS mode Press lt SEEK to rewind the tape to the previous selection or press SEEK gt to forward the tape to the next selection 4 24 Heater air conditioner and audio systems This system searches for the blank intervals between selections If there is a blank inter val within one program or there is no interval between programs the system may not stop in the desired or expected location Metal or chrome tape usage The cassette player is automatically set to high performance play when pl
36. 8 13 A WARNING Use only new fluid from a sealed con tainer Old inferior or contaminated fluid may damage the brake system The use of improper fluids can damage the brake system and affect the vehi cle s stopping ability CAUTION Do not spill the fluid on painted sur faces This will damage the paint If fluid is spilled wash with water 8 14 Maintenance and do it yourself WINDOW WASHER FLUID Windshield washer A LA fluid reservoir eae ADI1088 To check the fluid level look down the fill tube of the washer fluid reservoir in the engine compartment Add fluid when the low washer fluid warning light Canada only comes on To add fluid remove the reservoir cap and refill the reservoir This reservoir serves both the front and rear washer systems amp CAUTION Do not substitute engine anti freeze coolant for window washer solution This may result in damage to the paint BATTERY Keep the battery surface clean and dry Any corrosion should be washed off with a solution of baking soda and water Make certain the terminal connections are clean and securely tightened If the vehicle is not to be used for 30 days or longer disconnect the negative battery terminal cable to prevent dis charging amp WARNING e Do not expose the battery to flames or electrical sparks Hydrogen gas generated by the battery is explo sive Do not allow batt
37. A NISSAN Trailer Towing Guide U S only containing information on trailer towing ability and the special equipment may be obtained from an authorized NISSAN dealer Tongue load Keep the tongue load between 9 and 11 of the total trailer load If the tongue load becomes excessive rearrange cargo to al low for proper tongue load Gross axle weight 1012M Maximum gross vehicle weight maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating GVWR shown on the F M V S S certification label The gross ve hicle weight equals the combined weight of the unloaded vehicle passengers luggage hitch trailer tongue load and any other optional equipment In addition front or rear gross axle weight must not exceed the gross axle weight rating GAWR shown on the F M V S S certification label TOWING LOAD SPECIFICATION CHART UNIT Ib kg MAXIMUM TOWING LOAD MAXIMUM TONGUE LOAD TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer A genuine NISSAN trailer hitch is available from your NISSAN dealer USA only Make sure the trailer hitch is securely attached to the vehicle to help avoid per sonal injury or property damage due to sway caused by crosswinds rough road surfaces or passing trucks 3 500 1 588 350 159 amp CAUTION e Do not use axle mounted hitches e The hitch should not be at
38. CAUTION Never insert fingers into the seat track rails The rails may be sharp and could cause injury ADJUST PUSH to lower PD1176M HEAD RESTRAINT ADJUST MENT To raise the head restraint pull it up To lower push and hold the release button and push the head restraint down The head restraints on the two passenger bench seat equipped with the integrated child safety seats are not adjustable or removable 1 10 Seats restraints and supplemental air bag systems The center of the head restraint is 5 5 level with the center of your ears fe WRSO0096 Adjust the head restraints so the center is level with the center of your ears A WARNING Head restraints should be adjusted properly as they may provide signifi cant protection against injury in an ac cident Do not remove them Check the adjustment after someone else uses the seat Some seat arrangements may require re moval of the head restraints when the seat is in a storage position and not to be used by passengers ARS1137 ARMRESTS To use the armrests on any seat pull them down to the resting position D gt WRS0049 UNDERSEAT STORAGE TRAY Some front passenger seats have an under seat storage tray Pull the tray out to ac cess Seats restraints and supplemental air bag systems 1 11 Removing the second row bench seat DETACH tongue from auxiliary
39. Driver side power support seat controls Power slide seat height switch Power recliner seat ARS1120 Seats restraints and supplemental air bag systems 1 5 ARS1158 Seat lifter driver s seat only To raise the height of the seat lift the power seat height switch and release it when the desired position is reached To lower the height of the seat push the power seat height switch down and release it when the desired position is reached Driver side Lumbar support lever ARS1121 Lumbar support if so equipped for driver s seat The lumbar support provides lower back support to the driver Move the lever up or down to adjust the seat lumbar area 1 6 Seats restraints and supplemental air bag systems THREE PASSENGER SEAT e For most effective protection when ADJUSTMENT the vehicle is in motion the seat pas should be upright Always sit well Reclining back in the seat and adjust the seat To recline the three passenger seat lift up belt properly See Precautions on on the lever and lean back until the desired seat belt usage later in this section position is reached To bring the seatback After adjustment gently rock in the forward pull the lever up and lean your seat to make sure it is securely body forward locked amp WARNING e Do not recline the seatback while the vehicle is moving e Do not ride in a moving vehicle when the seatback is reclined T
40. ON iA Seat belt warning light and chime The light and chime remind you to fasten your seat belts If the driver s seat belt is NOT securely fastened when the ignition key is turned to ON or START the chime sounds for approximately 6 seconds and the light illuminates Refer to Seat belts in the Seats re straints and supplemental air bag systems section of this manual for precautions on seat belt usage A Supplemental air bag warning light When the ignition key is in the ON or START position the supplemental air bag warning light illuminates for about 7 seconds and then turns off This means the Air Bag Supple mental Restraint System is operational If any of the following conditions occur the supplemental air bag and pre tensioner seat belt systems need servicing and your vehicle should be taken to an authorized NISSAN dealer e The supplemental air bag warning light remains on after approximately 7 sec onds e The supplemental air bag warning light flashes intermittently e The supplemental air bag warning light does not come on at all Under these conditions the air bag supple mental restraint system and or pre tensioner seat belts may not function properly For additional details see Supplemental re straint system in the Seats restraints and supplemental air bag systems section of this manual A WARNING lf the supplemental air bag war
41. Removing and installing the second row bench Seat aaeeei 1 12 Reporting safety defects USA 9 21 S Safety Child safety sliding door lock s 3 5 Reporting safety defects USA 9 21 Seat belt Precautions on seat belt usage 1 39 Seat belt extenders n 1 53 Seat belt maintenance eee 1 54 Seat DeltSissweeiave n 1 39 Three point type with retractor 1 42 1 45 Two point type without retractor 1 51 Seat belt warning light eeeeeeeeeeeeee 2 9 S At POSIIONS sandina 1 20 Seating arrangement s e 1 19 Seats Five passenger seating s s s 1 28 Five passenger seating with cargo POON os cersceieiscesceavecaceseseevevensseniissaseusceets 1 29 Flexible SCatiN Gy sscisssecescesecessseceseesercacseas 1 12 Heated SCats inisinia 2 20 Integrated child safety seats 1 73 Manual front seat adjustment 1 3 Power support front Seat Seat POsitiONs rossius Second row bench seat Second row bucket seats Seven passenger seating Sliding three passenger seat 1 7 Three passenger bench seat in fully TORWAIC POSION sissa 1 29 Three passenger bench seat in Storage POSILION sitirans 1 27 Sgats floor MA S asenrenasnen naa 1 19 Self adjusting brakes cece 8 21 Seven passenger Seating cee 1 27 Shift lock release ecee ee eeeeeeeeeseeeees 5 7 Shifting Automatic transmission 0cce 5 7 Sliding thr
42. aaaeeeaeo Three way catalyst Tilting steering Wheel ccsecesesseeseeeees 3 11 Timing DOM sis saccassecsetescevessecvcizesessscessteveverseces 9 7 Tire Flat tierra Spare tire R Tire CHAINS piinatud Tire PlaCard sssccscivictvesseceeczesecisccsstezecseses Tire pressure Tire rotation TOOl Kitsas TYPOS Of roS isisisi Uniform tire quality grading 0 9 19 Wheels and tires z Wheel tire size Towing TOW truck tOWING wisscecscccccnsteedsecesctecseeres 6 12 Towing load specification chart 9 15 Taler TOWING cesses scskecessthdteassnttesesceeesss 9 14 10 5 Transmission Automatic transmission fluid ATF 8 12 Driving with automatic transmission 5 6 Selector lever lock release 5 7 Travel See registering your vehicle in another COUNTY wcsccevisesesssecceviserestsverereseeees 9 10 Turn signal switch U Under seat storage tray eee 1 11 Uniform tire quality grading 0 9 19 Vv Vanity MINOT suens srs aa 3 12 Vehicle dimensions and weights Vehicle identification Vehicle identification number VIN Vehicle identification number VIN CHASSIS NUMBER tisice 9 10 Vehicle identification number VIN plate 9 10 Vehicle loading information c0 9 13 Vehicle reCOVETY cccscescessecsestereceseesees 6 14 Vehicle security system ee 2 12 VeNtiIAlOlS i osne 4 2 10 6 Ww Warning Air bag wa
43. and then go off 5 e ge If any light fails to come on it may indicate a burned out bulb or an open circuit in the electrical system Have the system repaired promptly 2 8 Instruments and controls WARNING LIGHTS Engine oil pressure warning light This light warns of low engine oil pressure If the light flickers or comes on during normal driving pull off the road in a safe area stop the engine immediately and call an autho rized NISSAN dealer The engine oil pressure warning light is not designed to indicate a low oil level Use the dipstick to check the oil level See Engine oil in the Maintenance and do it yourself section of this manual f amp CAUTION Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately Such damage is not cov ered by warranty Turn off the engine as soon as it is safe to do so Charge warning light If the light comes on while the engine is running it may indicate the charging system is not functioning properly Turn the engine off and check the generator belt If the belt is loose broken missing or if the light re mains on see an authorized NISSAN dealer immediately CAUTION Do not continue driving if the belt is loose broken or missing Aah Door open warning light This light comes on when any of the doors are not closed securely while the ignition key is
44. band select button 17 18 19 20 21 VOLUME ON OFF control BASS TREBLE select button BASS TREBLE BALANCE FADE control button BALANCE FADE select button Tape eject button CLOCK button SCAN button AUTO SET button Radio tune button SHUFFLE station memory 6 button COMPRESSION station 5 memory button Dolby station memory 4 button Tape reverse station memory 3 button FAST FORWARD station memory 2 button REWIND station memory 1 button AM band select button SEEK button MUTE button CD button TAPE button Heater air conditioner and audio systems 4 19 FM AM RADIO WITH CASSETTE PLAYER NOTE Audio control features include com mand buttons for CD players which can be installed as optional equipment to upgrade the audio system A CD player is not in cluded with this system but can be pur chased as an option at any time Consult with an authorized NISSAN dealer for fea ture availability Audio main operation To turn the radio on turn the ignition key to ACC or ON If you listen to the radio with the engine not running turn the key to the ACC position Radio reception is affected by station signal strength distance from radio transmitter buildings bridges mountains and other external influences Intermittent changes in reception quality normally are caused by external influences Using a cellular phone in or near the vehicle may influence radio reception
45. bar appears in the display window Pressing the SELECT button either lt q increases or decreases the level of treble as indicated by the number of bar segments showing in the display window Following treble adjustment the display window shows the current setting for three seconds then returns to the display prior to adjustment Balance Balance control allows you to adjust the sound distribution between the right and left speakers Push the BAL button and the setting indica tor bar appears in the display window Press the SELECT button to shift the sound to the right speakers The single indicator bar moves to the right of the display win dow Press the SELECT button to shift the sound to the left speakers The single indicator bar moves to the left of the display window When the indicator bar is in the center position the sound is equally distrib uted between the right and left speakers Following balance adjustment the display window shows the current setting for three seconds then returns to the display prior to adjustment Fader Fader control allows you to adjust sound distribution between the front and rear speakers Push the FADE button and the setting indi cator bar appears in the display window Press the SELECT button lt to shift the sound to the front speakers The single indicator bar moves to the right of the dis play window Press the SELECT button P to shift the sound to the rear speakers
46. belt worn too high could increase the risk of inter nal injuries in an accident Seats restraints and supplemental air bag systems 1 39 a ea K We j P C al ARS1047 Be sure the seat belt tongue is se curely fastened to the proper buckle Do not wear the belt inside out or twisted Doing so may reduce its effectiveness Do not allow more than one person to use the same seat belt Never carry more people in the ve hicle than there are seat belts ARS1050 e if the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened it may indi cate a malfunction in the system Have the system checked by an au thorized NISSAN dealer All seat belt assemblies including retractors and attaching hardware should be inspected after any colli sion by an authorized NISSAN dealer NISSAN recommends that all seat 1 40 Seats restraints and supplemental air bag systems belt assemblies in use during a colli sion be replaced unless the collision was minor and the belts show no damage and continue to operate properly Seat belt assemblies not in use during a collision should also be inspected and replaced if either dam age or improper operation is noted e All child restraints and attaching hardware should be inspected after any collision Always follow the re straint manufacturer s in
47. blinking and come on steady Have the vehicle inspected by an authorized NISSAN dealer You do not need to have your ve hicle towed to the dealer Instruments and controls 2 11 CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability reduced fuel economy and possible damage to the emission control system AUDIBLE REMINDERS Key reminder chime The chime sounds if the driver s door is opened while the key is left in the ignition switch Remove the key and take it with you when leaving the vehicle Light reminder chime A chime sounds when the driver s door is opened with the headlight control switch on ignition switch is turned OFF The chime will not sound when the Auto lamp if so equipped shut off delay is acti vated Refer to the Autolamp Switch in structions later in this section Turn the headlight control switch to OFF when you leave the vehicle 2 12 Instruments and controls Brake pad wear warning The disc brake pads have audible wear warnings When a brake pad requires re placement it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the warning sound is heard VEHICLE SECURITY SYSTEM if so equipped IC0005 The vehicle security system provides audio and visual alarm signals
48. chains on dry roads Tire chains must be installed only on the front wheels and not on the rear wheels Front ADIO0656 CHANGING TIRES AND WHEELS Tire rotation Tires should be rotated every 7 500 miles 12 000 km Tighten wheel nuts to 80 ft lb 108 N m See Flat tire in the In case of emergency section for tire replacing procedures Maintenance and do it yourself 8 33 A WARNING After rotating the tires check and adjust the tire pressure Retighten the wheel nuts when the vehicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc Do not include the spare tire in the tire rotation For additional information regarding tires refer to Important Tire Safety Information in the Warranty Infor mation Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Information booklet Canada 8 34 Maintenance and do it yourself Wear indicator Location mark DI1035M Tire wear and damage A WARNING e Tires should be periodically in spected for wear cracking bulging or objects caught in the tread If excessive wear cracks bulging or deep cuts are found the tire s should be replaced The original tires have a built in tread wear indicator When the wear indicator is visible the tire s should be replaced e Improper service of the spare tire may result in serious personal in jury If it is
49. check for the cause or have an authorized NISSAN dealer do it promptly In addition you should notify an authorized NISSAN dealer if you think repairs are required When performing any checks or mainte nance work closely observe the Mainte nance precautions later in this section EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with an can be found later in this section Outside the vehicle The maintenance items listed here should be performed from time to time unless otherwise specified Tires Check the pressure with a gauge at least once a month and always prior to long distance trips including the spare and ad just to the specified pressure if necessary Check carefully for damage cuts or exces sive wear Wheel nuts When checking the tires make sure no wheel nuts are missing and check for any loose wheel nuts Tighten if necessary Tire rotation Tires should be rotated every 7 500 miles 12 000 km Wheel alignment and balance If the ve hicle should pull to either side while driving on a straight and level road or if you detect uneven or abnormal tire wear there may be a need for a wheel alignment If the steering wheel or seat vibrates at normal highway speeds wheel balancing may be needed e For additional information regarding tires refer to Important Tire Safety Informa tion in the Warranty Information Booklet US or Tir
50. coolant is leak ing or the cooling fan does not run stop the engine A WARNING Be careful not to allow your hands hair or clothing to come into contact with or get caught in engine belts or the engine cooling fan The engine cooling fan can start at any time when the coolant temperature is high 6 After the engine cools down completely check the coolant level in the reservoir tank with the engine running Add coolant to the reservoir tank if necessary Have your vehicle repaired at an authorized NISSAN dealer AFTER AN ACCIDENT Inertia fuel shut off switch ACE1020 INERTIA FUEL SHUT OFF SWITCH When the vehicle is involved in a collision the inertia fuel shutoff switch is designed to automatically stop the flow of fuel to the engine The impact forces needed to trigger the switch do not have to be great Parking lot bumping or road impacts such as driving over potholes may trigger the switch Once the inertia fuel shutoff switch is trig gered it must be reset before the engine can be started If your engine cranks but does not start after a collision take the In case of emergency 6 11 following steps to correctly reset the switch 1 Turn the key in the ignition to OFF 2 Check under the vehicle for leaking fuel 3 If you do not see or smell fuel push down the red reset button on the inertia fuel shut off switch 4 Turn the ignition key ON for a few sec onds then turn it OFF
51. described previously 2 38 Instruments and controls ROLLING CODE PROGRAMMING If your hand held transmitter appears to train to the HomeLink Universal Trans ceiver but does not open your garage door and your garage door opener was manufac tured after 1995 your garage door opener may have a Code Protected or Rolling Code feature This type of system will change the code of your garage door opener every time you open or close your garage door To determine if you have one of these systems depress the button on the HomeLink Universal Transceiver that you have just programmed If the LED on the HomeLink Universal Transceiver flashes rapidly for 1 to 2 seconds then remains on your garage door opener has a rolling code system To operate your rolling code garage door opener from your HomeLink Universal Transceiver follow these steps 1 Program your hand held transmitter to the HomeLink Universal Transceiver by following the procedures outlined previ ously if not yet programmed 2 Program your garage door opener re ceiver to recognize the HomeLink Uni versal Transceiver The HomeLink Uni versal Transceiver follows the same procedure to train to the receiver as your hand held transmitter did when it was first installed a Remove the cover panel from your garage door opener receiver The re ceiver should be located by the ga rage door opener motor b Locate the training button on the g
52. ejects When the EJ button is pushed while the compact disc is playing the disc ejects and the system turns off If the compact disc ejects and is not re moved within 10 seconds it is pulled back into the slot DISC indicator light DISC illuminates when a compact disc is loaded into the player Heater air conditioner and audio systems 4 31 5 COMPACT mIS MAGAZINE LJ v y J COMPACT DISC CD PLAYER if so equipped The compact disc player consists of two main components the 6 CD magazine and the CD changer Both components are lo cated on the center instrument panel con sole below the ashtray How to load the CD magazine To load the magazine with CDs first push the EJECT button on the CD changer to eject the magazine then remove the maga zine from the changer The inside of the CD magazine contains six shelves one for AHA1064 each CD to be loaded Carefully slide a CD label side up onto one of the shelves and push it in Repeat as desired loading up to six CDs CD magazine insert Once the desired number of CDs are loaded into the magazine insert the magazine back into the CD changer With the ignition switch OFF the CD maga zine loads into the CD changer Once the ignition switch is turned to ACC or ON the audio system returns
53. etc which are sold commercially Many of these additives intended for gum varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine Octane rating tips In most parts of North America you should use unleaded gasoline with an octane rating of at least 87 AKI Anti Knock Index num ber However you may use unleaded gaso line with an octane rating as low as 85 AKI Anti Knock Index in high altitude areas over 4 000 ft 1 219 m such as Colorado Montana New Mexico Utah Wyoming northeastern Nevada southern Idaho western South Dakota western Nebraska and the part of Texas which is directly south of New Mexico Using unleaded gasoline with an octane rating lower than stated above can cause persistent heavy spark knock Spark knock is a metallic rapping noise If severe this can lead to engine damage If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating or if you hear steady spark knock while holding a steady speed on level roads have an authorized NISSAN dealer correct the condition Failure to correct the condition is misuse Technical and consumer information 9 3 of the vehicle for which NISSAN is not responsible Incorrect ignition timing may result in spark knock after run and or overheating which may cause excessive fuel consumption or engine damage If any of the above symp
54. halo gen bulb A bulb can be replaced from inside the engine compartment without re moving the headlight assembly CAUTION e High pressure halogen gas is sealed inside the halogen bulb The bulb may break if the glass envelope is scratched or the bulb is dropped e When handling the bulb do not touch the glass envelope Removing the headlight bulb 1 Disconnect the negative battery cable 2 Disconnect the electrical connector from the rear end of the bulb 3 Turn the bulb retaining ring counterclock wise until it is free from the headlight reflector then remove it 4 Remove the headlight bulb by pulling it straight out Do not shake or rotate the bulb when removing it Replacing the headlight bulb 1 Insert the bulb into the headlight reflector with the flat side of the plastic base facing upward 2 Install the bulb retaining ring and turn it clockwise until it stops 3 Push the electrical connector into the bulb plastic base until it snaps and stops amp CAUTION DO NOT TOUCH THE BULB e Use the same number and wattage as originally installed Wattage 65 55 Bulb no 9007 HB5 e Aiming is not necessary after replac ing the bulb When aiming adjust ment is necessary contact an authorized NISSAN dealer e Do not leave the bulb out of the headlight reflector for a long period of time as dust moisture and smoke may enter the headlight body and affect the performance of the head l
55. if parts of the vehicle are disturbed SECURITY _ LICO004 Security indicator light This light will illuminate for the vehicle secu rity system This light blinks whenever the ignition switch is in the LOCK OFF or ACC posi tion This function indicates the security system equipped on the vehicle is opera tional How to activate the vehicle security system 1 Close all windows The system can be activated even if the windows are open 2 Remove the key from the ignition switch 3 Close all doors and the hood 4 Push the button on the keyfob All doors lock The hazard lights flash twice and the horn beeps once to indicate all doors are locked e When the button is pushed with all doors locked the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked The horn may or may not beep once Refer to silencing the horn beep fea ture later in this section for details 5 Confirm that the SECURITY indicator light comes on The SECURITY light glows for about 30 seconds and then begins to flash once every three seconds The system is now activated If during this 30 second time period the door is unlocked by the key or the keyfob or the ignition key is turned to ACC or ON the system will not activate If the key is turned slowly when locking the door the system may not activate Furthermore if the key is turned exces sively to the unloc
56. is set to any of the fan speed positions air is discharged from the rear vents at the corresponding speed When the rear seat fan control lever on the front panel is set to REAR A C the rear seat passengers control their own fan speed The rear seat air conditioner only works when the front seat air conditioner is operating Air conditioner CONTROLS Fan control dial This dial turns the fan on and off and controls fan speed 4 14 Heater air conditioner and audio systems T 2nd row ventilators SERVICING AIR CONDITIONING The air conditioning system in your NISSAN vehicle is charged with a refrigerant de signed with the environment in mind This refrigerant does not harm the earth s ozone layer Special charging equipment and lubricant are required when servicing your NISSAN air conditioner Using improper refrigerants or lubricants causes severe damage to your air conditioning system See Air condition ing system refrigerant and lubricant recom mendations in the Technical and con sumer information section of this manual An authorized NISSAN dealer is able to service your environmentally friendly air conditioning system A WARNING The air conditioner system contains refrigerant under high pressure To avoid personal injury any air condi tioner service should be done by an experienced technician with proper equipment Heater air conditioner and audio systems 4 15 A
57. level 8 8 Engine coolant temperature gauge 2 6 Cornering ohters ainis 2 19 Corrosion protection sses 7 4 Cruise COMO aces ccs cecsiepseneeeccccdenedexsecesevsee 5 10 Cup holders eee eeeeeeseeeeeeeeeseeeeeeaeeeeeees 2 25 D Daytime running light system Canada OMY esris asenita 2 17 Defogger switch Rear window defogger switch 2 16 Dimensions and weights DOOr IOCKS isna Door open warning light Drive belts ceeeeeesceeeeeeeeeeeseeeeeeeeeeeaees Driving Cold weather driving 5 16 Driving with automatic transmission 5 6 Precautions when starting and driving 5 2 10 2 E ECOMOMY f Blassirrisnn 5 12 Emission control information label 9 11 Emission control system warranty 9 20 Engine Before starting the engine 5 5 Capacities and recommended fuel WI CAINS oseti aiarad 9 2 Changing engine coolant 8 9 Changing engine oil 8 10 Changing engine oil filter ee 8 11 Checking engine coolant level 8 8 Checking engine oil level eee 8 9 Engine compartment check locations 8 7 Engine coolant temperature gauge 2 6 Engine cooling system ee 8 8 Engine Oilissa 8 9 Engine oil and oil filter recommendation eee eee cette 9 4 Engine oil pressure warning light 2 8 Engine oil viscosity c eee 9 5 Engine serial number w O11 Starting the engien 5 5 Exhaust gas Carbon monox
58. light and the rear interior light illuminate When the back door is closed the lights go off PERSONAL READING LIGHT Personal reading light PUSH to operate light AIC1088 The drivers side second and third row seating positions have a personal reading light located in the overhead trim panel To turn the light on press once on the right hand side of the light cover To turn the light off press again on the right hand side of the light cover A Do not use for extended periods of time with the engine stopped This could result in a discharged battery MAP LIGHTS C Map lights Map light switch Map light switch PUSH en PUSH on off AIC1097 To turn on the map lights press the switches To turn them off press the switches again A Do not use for extended periods of time with the engine stopped This could result in a discharged battery ILLUMINATED ENTRY SYSTEM The interior lights the cargo light the glove box light the stepwell lights near the sliding doors and on the front doors and the foot well lights near the drivers and front pas senger s feet illuminate when the front or sliding doors are opened Once the doors are closed these lights gradually dim to off within 30 seconds or turn off immediately when the key is turned to the ON position Battery saver If the vehicle doors are not fully closed and the interior lights remain illuminated th
59. necessary to repair the spare tire contact an authorized NISSAN dealer e For additional information regarding tires refer to Important Tire Safety Information in the Warranty Infor mation Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Information booklet Canada Replacing wheels and tires When replacing a tire use the same size tread design speed rating and load carrying capacity as originally equipped Recom mended types and sizes are shown in Wheels and tires in the Technical and consumer information section of this manual A WARNING e The use of tires other than those recommended or the mixed use of tires of different brands construc tion bias bias belted or radial or tread patterns can adversely affect the ride braking handling ground clearance body to tire clearance snow chain clearance speedometer calibration headlight aim and bumper height Some of these ef fects may lead to accidents and could result in serious personal in jury If the wheels are changed for any reason always replace with wheels which have the same off set dimen sion Wheels of a different offset could cause premature tire wear de grading vehicle handling character istics and or interference with the brake discs drums Such interfer ence can lead to decreased braking efficiency and or early brake pad shoe wear Refer to Wheel tire size in the Techni
60. not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation of the device HOOD 1 Pull the hood lock release handle 3 located below the instrument panel the hood then springs up slightly 2 Pull up on the lever at the front of the hood and raise the hood 4 WPDO0053 Insert the support rod into the slot on the underside of the hood When closing the hood reset the support rod to its original position lower the hood to approximately 12 inches above the latch and release it This allows proper engagement of the hood latch A WARNING e Make sure the hood is completely closed and latched before driving Failure to do so could cause the hood to fly open and result in an accident If you see steam or smoke coming from the engine compartment to avoid injury do not open the hood Pre driving checks and adjustments 3 9 REAR DOOR FUEL FILLER LID Door Door UNLOCK__ LOCK Rear o window UNLOCK PULL to open oS acs p Opener handle APD1065 Key operation To unlock the rear door turn the key coun terclockwise To open the rear door lift up on the opener handle near the license plate To close lower and push the rear door down securely A WARNING Do not drive with the rear door o
61. on dry pave ment Allow greater following distances on slippery roads Watch for slippery spots glare ice These may appear on an otherwise clear road in shaded areas If a patch of ice is seen ahead brake before reaching it Try not to brake while on the ice and avoid any sudden steer ing maneuvers Do not use the cruise control on slippery roads Snow can trap dangerous exhaust gases under your vehicle Keep snow clear of the exhaust pipe and from around your vehicle Starting and driving 5 17 ENGINE BLOCK HEATER if so equipped An engine block heater to assist extreme cold temperature starting is available through an authorized NISSAN dealer amp WARNING Do not use your heater with an un grounded electrical system or two pronged cheater adapters You can be injured by an electrical shock if you use an ungrounded connection 5 18 Starting and driving 6 In case of emergency Flat the chien eee ei ae ee 6 2 Changing a flat tire 0 eee eeeeeeeeeeteeeeteeeneees 6 2 JUMP Starting ee eee eeneeeseneeeeeneeeeeeneeteneeeenneeeee 6 8 PPUS Fic SUMING oreren ena sian i en 6 10 If your vehicle overheats eeeeeeseeeeneeeeeeees 6 10 After an accident 0 eeeesseeceeeeeeeeeeeeneeeeeenseess 6 11 Inertia fuel shut off switch eeen Towing your VeNICIE s ceceseeeeseeeeeeeeeeteeeeenes Towing recommended by Nissan Vehicle recovery freeing a stuck vehicle FLAT TIRE C
62. or drugs e ALWAYS observe posied speed lim its and never drive too fast for con ditions e ALWAYS use your seat belts and appropriate child restraint systems Pre teen children should be seated in the rear seat e ALWAYS provide information about the proper use of vehicle safety fea tures to all occupants of the vehicle e ALWAYS review this owner s manual for important safety information The inside pages of this manual contain a minimum of 50 recycled fibers including 10 post consumer fibers MODIFICATION OF YOUR VEHICLE This vehicle should not be modified Modification could affect its perfor mance safety or durability and may even violate governmental regulations In addition damage or performance problems resulting from modifications may not be covered under NISSAN warranties WHEN READING THE MANUAL This manual includes information for all options available on this model Therefore you may find some information that does not apply to your vehicle All information specifications and illustra tions in this manual are those in effect at the time of printing NISSAN reserves the right to change specifications or design without notice and without obligation IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual They are used in the following ways A WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury
63. position Headlights come on and all of the previously listed lights remain on To select the high beam push the turn signal lever away from you The lever latches in place Pull it back to select the low beam To turn the interior lights on push the head light switch The interior lights come on Push the headlight switch again to turn the interior lights off lax NS PUSH to C PUSH darken brighten AIC1059 Instrument brightness control The instrument brightness control operates when the light switch is in the pa or ZD position or when the autolamp system is operating Pressing the A side of the switch bright ens the instrument panel lights pressing the V side of the switch dims the instrument panel lights Passing signal Pulling the lever toward you turns the head light high beam on Release it and the headlight high beam goes off Daytime running light system Canada only The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released The day time running lights operate with the head light switch in the OFF position or in the zpa position Turn the headlight switch to the 4D position for full illumination when driving at night If the parking brake is applied before the engine is started the daytime running lights do not illuminate The daytime running lights illuminate once the parking brake is released The daytime run
64. pressure to the COLD pres sure COLD pressure After the vehicle has been parked for three hours or more or driven less than 1 mile 1 6 km COLD tire pressures are shown on the tire placard affixed to the inside of the glove box In case of emergency 6 7 Jack and tool kit storage bag WCE0005 Stowing the damaged tire and tools 1 To raise the tire to the stowed position install the retainer through the wheel center and turn the wheel lug wrench clockwise until the tire is raised to its original position underneath the vehicle The spare tire hex nut ratchets when the tire is raised It won t allow you to over tighten Check for proper seating against under body supports If necessary loosen tire reposition and retighten 6 8 In case of emergency 3 Securely store the jacking equipment in the vehicle amp WARNING e Always make sure that the spare tire and jacking equipment are properly secured after use Such items can become dangerous projectiles in an accident or sudden stop The spare tire is designed for emer gency use See specific instructions under the heading Wheels and tires in the Maintenance and do it yourself section of this manual JUMP STARTING To start your engine with a booster battery the instructions and precautions below must be followed amp WARNING If done incorrectly jump starting can lead to a battery explosion resulting
65. quality Power Volume control Push the VOL knob to turn the radio on Push the VOL knob once more to turn the radio OFF Turn the knob to the right to increase vol ume or to the left to decrease volume If the knob is set above a certain volume level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition is turned back on Adjusting tone quality and speaker bal ance Bass Bass control allows you to adjust the lower bass frequencies to your preference Push the BASS button and the setting indi cator bar appears in the display window Pressing the SELECT button either A or WV increases or decreases the level of bass as indicated by the number of bar segments showing in the display window Following bass adjustment the display win dow shows the current setting for three seconds then returns to the display prior to adjustment 4 20 Heater air conditioner and audio systems Treble Treble control allows you to adjust the higher treble frequencies to your prefer ence Push the TREB button and the setting indi cator bar appears in the display window Pressing the SELECT button either A or V increases or decreases the level of treble as indicated by the number of bar segments showing in the display window Following treble adjustment the display window shows the current setting for three seconds then returns to the display prior to adjustment Balance
66. quired 9 Turn the engine off and wait several minutes Check the oil level with the dipstick Add engine oil if necessary LOOSEN ADIO010 Oil filter CHANGING ENGINE OIL FILTER 1 Park the vehicle on a level surface and apply the parking brake 2 Turn the engine off 3 Place a large drain pan under the oil filter 4 Loosen the oil filter with an oil filter wrench Then remove the oil filter by turning it by hand CAUTION Be careful not to burn yourself The engine oil may be hot 5 Wipe the engine oil filter mounting sur face with a clean rag Be sure to remove any old gasket material remaining on the mounting surface of the engine 6 Coat the rubber gasket on the new filter with clean engine oil 7 Screw on the oil filter in until a slight resistance is felt then tighten an addi tional 2 3 turn 8 Start the engine and check for leakage around the oil filter Correct as required 9 Turn the engine off and wait several minutes Check the oil level Add engine oil if necessary Maintenance and do it yourself 8 11 AUTOMATIC TRANSMISSION FLUID Automatic transmission l n fluid dipstick 7 ADI1085 A WARNING e When the engine is running keep hands jewelry and clothing away from any moving parts such as the cooling fan and drive belts e Automatic transmission fluid is poi sonous and should be stored care fully in marked containers out o
67. removed APDO0046 To increase cargo area space the second row bench seat can be removed and the three passenger sliding seat can be moved up to the second row position Third seat folded down in second seating position with second row seat removed APD0047 The third seat can be folded down into a tabletop Seats restraints and supplemental air bag systems 1 23 Second row seat removed third row seat folded down APDO0048 With the third seat folded down and the second seat removed cargo can be placed in between the front seats and the third row seat Passengers should not be allowed to ride in areas meant for cargo Passen gers should always be properly re strained in seat belts Second seat folded down third seat folded up APDO050 The second row seat can be folded down and the third row seat can be moved just behind it in a storage position 1 24 Seats restraints and supplemental air bag systems Seven passenger seating with bucket seats in second row third seat in seating position 1 H 0 ad ad sy CE More leg room APD0128 With second row bucket seats The normal seating arrangement for seven passengers is with the three passenger bench seat in seating position 1 This provides more leg room for the passengers sitting in the third row One bucket seat removed One bucket seat removed ARS1195
68. routing Front facing A n B ra ee Front apse LF G ARS1170 3 Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment Front facing NX r q ARS1171 4 Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure it is securely in place 5 If it is not secure try to tighten the seat belt again or put the restraint in another seat 6 Check to make sure the child restraint is properly secured prior to each use Rear facing Rear facing When you install a child restraint in a rear center seat follow these steps 1 Position the child restraint on the seat as illustrated Always follow the restraint manufacturer s instructions Seats restraints and supplemental air bag systems 1 57 ARS1173 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing Rear facing PULL to tighten ARS1174 3 Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment 1 58 Seats restraints and supplemental air bag systems Rear facing Front 4 Before placing the child in the child re
69. second row bench seat There is a two buckle seat belt system for the seating position of the second row bench seat next to the passenger side slid ing door A WARNING e Itis very important that you follow the instructions in this section before anyone rides in this seating position of the two passenger bench seat e Failure to do so may result in im proper positioning of seat belt which could lead to increased likelihood or severity of injury in a sudden stop or collision 1 46 Seats restraints and supplemental air bag systems Two passenger bench seat we ee seat belt anchor tongue attached to auxiliary buckle Lower seat belt anchor ARS1127 The two passenger bench seat in the sec ond row has a seat belt system made up of two buckles and two tongues There are two body attaching points one upper and one lower that attach each end of the seat belt webbing Upper seat belt anchor Seat belt clip __ for storage of seat belt when WRSO051 One of the seat belt tongues has two win dows or holes and the other has only one window The seat belt tongue with one window attaches to the auxiliary buckle mounted to the side of the seat The seat belt tongue with two windows should be positioned properly and fastened to the buckle mounted in the middle of the seat When the two buckle seat belt system is not in use the webbing can
70. srren neika 7 3 To protect your vehicle from corrosion 7 5 Cleaning interior ceceeeeeseeeseeeeeesseeteeeeeeetaee 7 3 CLEANING EXTERIOR AI1002M In order to maintain the appearance of your vehicle it is important to take proper care of it In the following cases please wash your vehicle as soon as possible to protect the paint surface e after a rainfall to prevent possible dam age from acid rain e after driving on coastal roads when contaminants such as soot bird droppings tree sap metal particles or bugs get on the paint surface 7 2 Appearance and care e when dust or mud builds up on the surface Whenever possible store or park your ve hicle inside a garage or in a covered area When it is necessary to park outside park in a shady area or protect the vehicle with a body cover Be careful not to scratch the paint sur face when putting on or removing a body cover WASHING Wash dirt off with a wet sponge and plenty of water Clean the vehicle thoroughly using a mild soap a special vehicle soap or general purpose dishwashing liquid mixed with clean lukewarm never hot water A CAUTION e Do not wash the vehicle with strong household soap strong chemical detergents gasoline or solvents e Do not wash the vehicle in direct sunlight or while the vehicle body is hot as the surface may become water spotted e Avoid using tight napped or rough cloth
71. steering wheel slightly right and left amp WARNING Never remove or turn the key to the LOCK position while driving The steer ing wheel will lock This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury KEY POSITIONS LOCK Normal parking position OFF The engine can be turned off without locking the steering wheel if the key is left in the ignition ACC Accessories This position activates electrical accesso ries such as the radio when the engine is not running ON Normal operating position This position turns on the ignition system and the electrical accessories START This position activates the starter motor which starts the engine BEFORE STARTING THE ENGINE Make sure the area around the vehicle is clear Maintenance items listed here should be checked periodically for example each time you check engine oil Check that all windows and lights are clean Visually inspect tires for their appearance and condition Also check tires for proper inflation Lock all doors Position seat and adjust head restraints Adjust inside and outside mirrors Fasten seat belts and ask all passengers to do likewise Check the operation of warning lights when key is turned to the ON position See Warning Indicator lights and audible reminders in the Instrument and con trols section STARTING THE ENGINE 1 Apply the parki
72. straint use force to tilt the child restraint from side to side and tug it forward to make sure it is securely in place 5 If it is not secure try to tighten the seat belt again or put the restraint in another seat 6 Check to make sure the child restraint is properly secured prior to each use INSTALLATION ON SECOND AND THIRD ROW OUTBOARD POSITIONS Front facing The following instructions apply to second row bucket seats the second row bench seat and the outboard positions of the three passenger bench seat A WARNING When installing a child restraint in the two passenger bench seat if it is placed in the seating position next to the passenger side sliding door be sure both the auxiliary buckle and main buckle are properly fastened Failure to do so could increase the chance and or severity of injury in an accident A WARNING e The three point belt in your vehicle is equipped with locking mode re tractor which must be used when installing a child restraint e Failure to use the retractor s locking mode will result in the child restraint not being properly secured The re straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision Front facing Front I 2 a WRS0055 When you install a child restraint in a sec ond row bucket seat the second row bench seat or the outboard positions of the three passenger bench seat follow these s
73. terns Usually the ready condition can be obtained by ordinary usage of the vehicle If a powertrain system component is repaired or the battery is disconnected the vehicle may be reset to a not ready condition Before taking the I M test drive the vehicle through the following pattern to set the vehicle to the ready condition If you cannot or do not want to perform the driving pattern an authorized NISSAN dealer can conduct it for you A WARNING Always drive the vehicle in a safe and prudent manner according to traffic conditions and obey all traffic laws 1 Start the engine when the engine coolant temperature gauge needle points to C Allow the engine to idle until the gauge needle points between the C and H nor mal operating temperature 2 Accelerate the vehicle to 55 MPH 88 km h then quickly release the accelera tor pedal completely and keep it released for at least 6 seconds 3 Quickly depress the accelerator pedal for a moment then drive the vehicle at a speed of 53 to 60 MPH 86 to 96 km h for at least 5 minutes 4 Stop the vehicle 5 Accelerate the vehicle to 35 mph 55 km h and maintain the speed for 20 seconds 6 Repeat steps four through five at least three times 7 Accelerate the vehicle to 55 mph 88 km h and maintain the speed for at least 3 minutes 8 Stop the vehicle shift lever in the P or N position 9 Rev the engine up between 2 500 and 3 500 rpm and hold
74. the engine is running it may indicate a potential emission control mal function The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing or if the vehicle runs out of fuel Check to make sure the fuel filler cap is installed and closed tightly and that the vehicle has at least three gallons of fuel in the fuel tank After a few driving trips the ane lamp should turn off if no other potential emission control system malfunction exists Operation The malfunction indicator lamp will come on in one of two ways e Malfunction indicator lamp on steady An emission control system malfunction has been detected Check the fuel filler cap If the fuel filler cap is loose or missing tighten or install the cap and continue to drive the vehicle The N lamp should turn off after a few driving trips If the Senf lamp does not turn off after a few driving trips have the vehicle inspected by an authorized NISSAN dealer You do not need to have your vehicle towed to the dealer e Malfunction indicator lamp blinking An engine misfire has been detected which may damage the emission control sys tem To reduce or avoid emission control system damage a do not drive at speeds above 45 MPH 72 km h b avoid hard acceleration or deceleration c avoid steep uphill grades d if possible reduce the amount of cargo being hauled or towed The malfunction indicator lamp may stop
75. the original tire used on the front wheels drive wheels Use tire chains only on the front original tires Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire Replace the spare tire as soon as the tread wear indicators appear Do not use the spare tire on other vehicles Do not use more than one spare tire at the same time Do not tow a trailer when the TEM PORARY USE ONLY spare tire is installed CAUTION e Do not use tire chains on the TEM PORARY USE ONLY spare tire Tire chains will not fit properly and may cause damage to the vehicle Because the TEMPORARY USE ONLY spare tire is smaller than the original tire ground clearance is re duced To avoid damage to the ve hicle do not drive over obstacles Also do not drive the vehicle through an automatic car wash since it may get caught 9 Technical and consumer information Capacities and recommended fuel lubricants Fuel recommendation cceesceeeeeeeeeeneeeeeee Engine oil and oil filter recommendation Recommended SAE viscosity numbet Air conditioner system refrigerant and lubricant recommendations eee Specifications ccceeeeeceeeeeeeeseeeeseeeeesseeeeeeneeeeees ENGINE eereeeer rece e A tere Wheels and tir S cccceeeeeeeeeeeeseeseeeeeeees Dimensions and weights s e When traveling or registering your vehicle in another COUM ransonn
76. the tank is getting low Refill the fuel tank before the gauge registers E empty amp CAUTION e lf the vehicle runs out of fuel the ane malfunction indicator lamp MIL may come on Refuel as soon as possible After a few driving trips the Sane lamp should turn off If the lamp remains on after a few driving trips have the vehicle inspected by an authorized NISSAN dealer e For additional information see the Malfunction indicator lamp MIL later in this section MESSAGE CENTER if so equipped Reset button QU y PUSH 2 Average Fuel Economy Distance To Empty Outside Air Temperature WIC0083 The message center only works with the ignition in the ON position The message center displays the following information e Outside air temperature e Average fuel economy e Distance to empty You can select the different features by pushing the message center reset button Outside air temperature Press the message center reset button until the outside air temperature is displayed The outside air temperature sensor is located in front of the radiator The sen sor may be affected by road or engine heat wind direction and other driving conditions The display may differ from the actual outside temperature or the temperature displayed on various signs or billboards Average fuel economy Press the message center reset button until fuel economy is dis
77. the use then SEL button to choose TRAFFIC ON then use the seek or scan control to look for a station that may transmit traffic reports the radio will display a TRAF icon to show it is in traffic mode and tuned to a station that may transmit traffic reports If the radio searches through the whole band and then returns to the previous station it was originally playing there are no stations in the area that are transmitting traffic reports If a cassette or compact disc is being played while the traffic option is on and the station previously tuned into displays a traffic bul letin the radio will pause the cassette or compact disc and broadcast the bulletin then resume playing the cassette or com pact disc Using RDS to search for programming type Certain areas have a limited number of stations that transmit RDS Many stations transmit call letters and frequencies only Searching or scanning by program type may yield a limited number of selections Press the RDS CLK button until FIND CLASSIC is displayed then use the SEL button to choose between CLASSIC COUNTRY INFO JAZZ RELIGUS Reli Heater air conditioner and audio systems 4 29 gious ROCK SOFT and TOP40 When you have chosen a program type use the SEEK SCAN or AUTOSET controls to look for a station transmitting that kind of pro gram If the radio searches through the whole band and then returns to the previous station it was originally playing there ar
78. to its original position otherwise it may be damaged when the engine hood is opened e Make sure the wiper blades contact the glass otherwise the arms may be damaged from wind pressure Maintenance and do it yourself 8 19 Lift up the wiper blade Remove the wiper blade LO ADI1114 Rear window wiper blade 1 Lift the wiper arm away from the wind shield 2 Push the tab then move the wiper blade down the wiper arm to remove 3 Insert a new wiper blade onto the wiper arm and press down until the blade clicks into place 8 20 Maintenance and do it yourself PARKING BRAKE AND BRAKE PEDAL ce PUSH again to C D release ke parking D pusu brake to set parking brake 5 6 clicks under depressing force of 44 Ib 196 N ADI1089 CHECKING PARKING BRAKE From the released position push the park ing brake foot lever down If the number of clicks is out of the range listed above see an authorized NISSAN dealer Under depressing force of 3 in 75 mm 110 Ib 490 N or more ADI0027 CHECKING BRAKE PEDAL With the engine running check the distance between the upper surface of the pedal and the floor If it is out of the range shown above see an authorized NISSAN dealer Self adjusting brakes Your vehicle is equipped with self adjusting brakes The front disc type brakes self adjust every time the brake pedal is appl
79. to its previous mode With the ignition switch in the ACC or ON 4 32 Heater air conditioner and audio systems position the CD magazine loads into the CD changer and begins play with disc one track one CD button Push this button to switch from radio or tape mode to CD mode CD play begins auto matically if at least one disc is loaded in the magazine The display window shows the CD number for three seconds then the track number for three seconds then displays both together for the remainder of the track If the CD button is pushed while in the radio or tape mode and there are no CDs loaded in the magazine the display window flashes a NO DISC message for 4 seconds CD Player controls SEEK Push lt q SEEK to select the previous track number or push SEEK gt to select the next track number After the last track on a disc pushing SEEK jp selects the first track of the same disc SELECT DISCS Push lt Q TUNE to select the previous CD in the magazine Push TUNE p gt to select the next CD in the magazine SCAN Push this button to audition the first 10 seconds of each track on a disc At the end of the disc the SCAN function continues with the first track on the same disc The display window flashes the track number being auditioned during the SCAN function FF Fast Forward Press this button to advance the CD mecha nism and move ahead on the disc If held for less than three seconds this button ca
80. two different heights and in a storage position To install the parcel shelf e Position the right side of the parcel shelf in to one of the shelf positions on the right side luggage compartment trim panel e Position the left side of the parcel shelf into the matching position same height on the left side luggage compartment trim panel e Slide the parcel shelf lock knob fully to the left side latch in green dot position e Turn the parcel shelf lock knob clock wise until securely locked The parcel shelf is also equipped with a parcel shelf net to keep packages on the parcel shelf from moving around while the vehicle is in motion The parcel shelf net is permanently at tached to the back side of the parcel shelf Pull the parcel shelf net over the packages and attach the three loops to the three retainers on the bottom side of the parcel shelf Make sure the parcel shelf is securely locked before covering the packages with the parcel shelf net To remove the parcel shelf e Unlock the parcel shelf net e Remove all packages from the parcel shelf e Turn the parcel shelf lock knob counter clockwise until loose maximum two turns e Slide the parcel shelf lock knob fully to the right side unlatch in red dot posi tion e Remove the parcel shelf from the left side luggage compartment trim panel then the right side luggage compartment trim panel and reposition the parcel shelf where desired
81. two seconds once more The hazard lights will flash three times to confirm that the horn beep feature has been reactivated Deactivating the horn feature does not si lence the horn if the alarm is triggered Pre driving checks and adjustments 3 7 BATTERY REPLACEMENT BATTERY REPLACEMENT Replace the battery as follows 1 Open the lid using a coin 2 Replace the battery with a new one Insert the batteries as illustrated above 3 8 Pre driving checks and adjustments Recommended CR2025 3V or equivalent battery 3 Close the lid securely 4 Press the button then theg button two or three times to check the keyfob opera tion APD1087 Panasonic If the batteries are removed for any reason other than replacement perform step 4 e An improperly disposed battery can hurt the environment Always conform to local regulations for battery disposal e The keyfob is water resistant how ever if it does get wet immediately wipe completely dry e The operational range of the keyfob extends to approximately 30 ft 10 m from the vehicle This range may vary with conditions FCC Notice Changes or modifications not expressly approved by the manufacturer for com pliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules and RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may
82. 5 CAUTION Third row passengers must be very careful when exiting because of the auxiliary seat belt It is important to step over the seat belt guide and belt webbing to avoid tripping Unfastening the seat belts To unfasten the seat belt press the button on the buckle The seat belt automatically retracts 1 48 Seats restraints and supplemental air bag systems Checking seat belt operation Three point type seat belt with retractor Seat belt retractors are designed to lock seat belt movement 1 when the seat belt is pulled quickly from the retractor and 2 when the vehicle slows down rapidly To increase your confidence in the seat belts check their operation as follows e Grasp the shoulder belt and pull quickly forward The retractor should lock and restrict further belt movement If the retractor does not lock during this check or if you have any questions about seat belt operation see an authorized NISSAN dealer THREE PASSENGER BENCH SEAT IN THE SECOND ROW POSITION Fastening the seat belts When the three passenger bench seat is moved up to the second row position the passenger seated near the passenger side sliding door needs to use the double window tongue and the standard buckle only Because the three passenger bench seat is wider and closer to the passenger side sliding door the single window seat belt tongue and the auxiliary buckle are not necessary 1 Adjust the seat
83. EQUIPPA ieii iinitan 4 34 Heater and air conditioner automatic Rear audio controls if so equipped 4 35 if SO equipped sseceerecsrees ters eeeecseesteeneeenecees 4 11 E E 4 37 Automatic operation PEE E T AT AT ETE 4 12 Autovision family entertainment system Rear seat air conditioner if so equipped 4 14 FES if So CQUIPPEd ccceecsesecteseeteseeeees 4 37 CONTOS ree er er Beate ti ieee 4 14 Rear seat entertainment module Servicing air conditioning cee 4 15 RSEM if So equipped ceseseeseeeeseeeeeeeee 4 41 Audio SYS EM sssecssesseestessneeseeeetesnnesseteneetaetanaes 4 16 Care and MAENAN Ce an 4 43 PRAGIO epaiei lt cdeaddexnaccsaddececeadadcateyasiecesszaed 4 16 Troubleshooting EANA AE aie eee esitcek 4 44 FM radio reception ssssstseessiten 4 16 Specifications y ccsdneimsctntiee incr lee 4 45 AM radio rECEPHON oxcasttsesbaiacettcnsctntestessssnintonnie 4 16 Car phone or CB radio cccecceceeseeteeeeereeeeeeees 4 46 Audio operation precautions eee 4 17 VENTILATORS y c i D ch Ty Wap g ID D l VANS LA AHA1056 AHA1055 CENTER VENTILATORS SIDE VENTILATORS Open close and adjust the air flow direction Open
84. Foreword Welcome to the growing family of new NISSAN owners This vehicle is delivered to you with confidence It was produced using the latest techniques and strict quality control This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure Please read through this manual before operating your vehicle A separate Warranty Information Booklet explains details about the warranties covering your vehicle The NISSAN Ser vice and Maintenance Guide explains details about maintaining and servicing your vehicle Additionally a separate Customer Care Lemon Law Booklet U S only will explain how to resolve any concerns you may have with your ve hicle as well as clarify your rights under your state s lemon law Your NISSAN dealership knows your ve hicle best When you require any service or have any questions they will be glad to assist you with the extensive resources available to them READ FIRST THEN DRIVE SAFELY Before driving your vehicle read this own ers manual carefully This will ensure famil iarity with controls and maintenance re quirements assisting you in the safe operation of your vehicle A WARNING IMPORTANT SAFETY INFORMATION REMINDERS FOR SAFETY Follow these important driving rules to help ensure a safe and comfortable trip for you and your passengers e NEVER drive under the influence of alcohol
85. GCIS aiaee an RES 2 8 Checking DUDS sisstin eeeceeeeeseeeeeeeteeeteeeeeeeeteees 2 8 Warning QMS cecc ieieccisescustectvanteenectces estiu 2 8 Indicator liQhtS c23 scsesec esssnensesecessecetsncenessee 2 10 Audible reminders eeseeeseeeeeneeeeeneeeeeaees 2 12 Vehicle security system if so equipped 2 12 Windshield wiper and washer switch 2 15 Rear window wiper and washer switches 2 16 Rear window defogger SWItCh eee 2 16 Headlight and turn signal Switch ee 2 16 Headlight control switch sesser 2 16 Autolamp switch if so equipped 2 18 Turn Signal SWI Ch iscissi 2 19 Cornering light cceeceeeeseeeeeeeeneeeeeeeeeeeaes 2 19 Hazard warning flasher SWitCN 0 eee 2 19 POM este eee ae Annie eee A eaennehas 2 20 Heated seats if SO equipped 2 20 Rear power socket ccessceeeeeseeseeeeenseeeeneeenes 2 22 Cigarette lighter and ashtray accessory 2 23 Storage es sche ceckslendaechardesdenducessieessitiedeueceveedendesevSenein 2 24 Map pockets carsoniana 2 24 Conversation MII OF eceeceseeeeteeeteteteeeereeee 2 24 Gup holderswiaxtctsitsansteliedstiniaeen i 2 25 Glove box Cargo net Parcel shelf if SO equipped eee 2 28 LUGGAGE WACK ss sicicctestsetensids apseceetecaceesecceneteeeses 2 30 WINGOWS 1425 it tits ion Petite iin eis 2 30 Power WINDOWS eiempi 2 30 Power vent windows if so equipped 2 32 Manua
86. HANGING A FLAT TIRE If you have a flat tire follow the instructions below Stopping the vehicle 1 2 3 Safely move the vehicle off the road and away from traffic Turn on the hazard warning flashers Park on a level surface and apply the parking brake Move the gearshift lever to the P Park position Turn off the engine Raise the hood to warn other traffic and to signal professional road assistance personnel that you need assistance Have all passengers get out of the ve hicle and stand in a safe place away from traffic and clear of the vehicle A WARNING e Make sure the parking brake is se curely applied and the automatic transmission is shifted into P Park e Never change tires when the vehicle is on a slope ice or slippery areas This is hazardous 6 2 In case of emergency e Never change tires if oncoming traf fic is close to your vehicle Wait for professional road assistance CE1003M Blocking wheels Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire This prevents the vehicle from roll ing when it is jacked up A WARNING Be sure to block the wheel as the ve hicle may move and result in personal injury Jack and tool kit storage bag ACE1025 Getting the spare tire and tools Remove the jack jack storage bag located under the third row seat Hex shaped end of lug wre
87. ICATION MARK can not be found An ILSAC grade GF I and GF II oil can also be used Mineral based or synthetic type oils may be used in your NISSAN vehicle These oils must however meet the API quality and SAE viscosity ratings specified for your ve hicle Do not mix mineral based and syn thetic type oils in the engine Oil additives NISSAN does not recommend the use of oil additives The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed Oil which may contain foreign matter or has been previously used should not be used Oil viscosity The engine oil viscosity or thickness changes with temperature Because of this it is important to select the engine oil viscos ity based on the temperatures at which the vehicle will be operated before the next oil change The chart Recommended SAE viscosity number shows the recommended oil viscosities for the expected ambient tem peratures Choosing an oil viscosity other than that recommended could cause seri ous engine damage Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high quality genuine NISSAN oil filter When replacing use a genuine NISSAN oil filter or its equivalent for the reason de scribed in Change intervals Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters Oil and filte
88. L to release Ye steering wee VA ag z APD1051 TILT OPERATION Push the lock lever down and adjust the steering wheel up or down to the desired position Pull the lock lever up firmly to lock the steering wheel in place Gently pull down on the wheel to make sure it is properly locked A WARNING Do not adjust the steering wheel while driving You could lose control of your vehicle and cause an accident Pre driving checks and adjustments 3 11 SUN VISORS MIRRORS fe OPEN x A y Ki CLOSE Iluminated vanity mirror WPD0012 VANITY MIRROR Access the mirror by pulling the sun visor down and lifting the cover up The vanity mirror will illuminate when the mirror cover is opened 3 12 Pre driving checks and adjustments Indicator light CH Memory seat L and mirror position 1 button MEMORY SEAT Memory seat and mirror position 2 button APD1062 MEMORY DRIVER SEAT AND MIRRORS if so equipped The memory driver seat and mirror function provides a convenient way to recall a driv ers seat and outside mirror positions Un locking the doors using the multi remote controller or by pressing the memory seat position 1 or position 2 button activates the memory driver seat and mirrors Remote keyless entry system entry Pressing the g button on the keyfob un loc
89. LL down to lock into place PUSH to open LIC0020 CONVERSATION MIRROR Some vehicles are equipped with a conver sation mirror Push to open the conversa tion mirror Pull down to lock mirror into place Adjust mirror to desired position Push again to close the conversation mirror AIC1065 CUP HOLDERS To use the cup holder pull out To store the cup holder push it back in The cup holder can be adjusted to fit smaller cups by pushing the arms in The arms have three detents and then return to the fully open position Do not pull the cup holder arms or force a cup or bottle into the cup holder to adjust to a larger cup position A WARNING The cup holder should not be used while driving so full attention may be given to vehicle operation CAUTION e Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink If the liq uid is hot it can scald you or your passenger e Use only soft cups in the cup holder Hard objects can injure you in an accident Driver side second row bucket seat Second row cup holder Vehicles equipped with second row bucket seats have a cup holder attached to the side of the seat Instruments and controls 2 25 Second row bench seat PULL j to open WIC0022 Vehicles equipped with a second row bench seat have a cup holder attached to the front center of th
90. NISSAN dealer Maintenance and do it yourself 8 15 DRIVE BELTS Air conditioner Water pump compressor Power steering fluid pump Crank pulley Generator Tension checking points ADIO060 A WARNING Be sure the ignition key is in the OFF or LOCK position The engine could rotate unexpectedly 1 Visually inspect each belt for signs of unusual wear cuts fraying or looseness If the belt is loose or in poor condition have it replaced or adjusted by an autho rized NISSAN dealer 8 16 Maintenance and do it yourself 2 Have the belts checked regularly for con dition and tension in accordance with the maintenance schedule found in the NISSAN Service and Maintenance Guide SPARK PLUGS CORRECT WRONG DO NOT HOLD the cable ADI0061 REPLACING SPARK PLUGS A WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely CAUTION Be sure to use the correct socket to remove the spark plugs An incorrect socket can damage the spark plugs Platinum tipped a ADI1100 Platinum tipped spark plugs It is not necessary to replace platinum tipped spark plugs as frequently as conven tional type spark plugs because they last much longer Follow the maintenance schedule but do not reuse the spark plugs by cleaning or regapping e Always replace spark plugs with rec ommended or equivalent ones 1 Disconn
91. PLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental air bag system are placed in the vehicle as shown in the illustration ARS1123 wiag SS 4 KA RPM x 1000 G ty SS We On N own jun Y 4 j By WRS0090 SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light displaying ar in the instrument panel monitors the circuits of the supplemental air bag and pretensioner systems The circuits monitored by the air bag warning light in clude the diagnosis sensor unit supplemen tal air bag modules pre tensioner seat belt system and all related wiring When the ignition key is in the ON or START position the supplemental air bag warning light illuminates for about 7 seconds and Seats restraints and supplemental air bag systems 1 37 then turns off This means the system is operational If any of the following conditions occur the supplemental air bag and pre tensioner seat belt systems need servicing and should be taken to your nearest authorized NISSAN dealer e The supplemental air bag warning light remains on after approximately 7 sec onds e The supplemental air bag warning light flashes intermittently e The supplemental air bag warning light does not come on at all Under these conditions the supplemental air bag and or pre tensioner seat belts may not operate properly It must be checked and repaired Ta
92. RNING Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obsiructions over the LATCH system anchors such as seat belt webbing or seat cushion material The child re straint will not be secured properly if the LATCH system anchors are ob structed 1 To install the LATCH system compatible child restraint insert the child restraint LATCH system anchor attachments into the anchor points on the rear seat If the child restraint is equipped with a top tether see Top Tether Strap Child Re straint later in this section for installation instructions 2 After attaching the child restraint and before placing the child in it use force to tilt the child restraint from side to side and tug it forward to make sure that the child restraint is securely held in place 3 Check to make sure that the child re straint is properly secured prior to each use 1 68 Seats restraints and supplemental air bag systems CHILD RESTRAINT WITH TOP TETHER STRAP A child restraint anchored with a top tether strap can be installed on the second row bench seat a second row bucket seat or the three passenger bench seat in the sec ond or third row The chart indicates where the tether strap must be attached and the section of this manual that contains the instructions for tethering Bucket seat Position Second row center of seat Anchor bracket on back of bucket seat
93. ROTECT YOUR VEHICLE FROM CORROSION wash and wax your vehicle often to keep the vehicle clean e always check for minor damage to the paint and repair it as soon as possible e keep drain holes at the bottom of the doors open to avoid water accumulation check the underbody for accumulation of sand dirt or salt If present wash with water as soon as possible CAUTION e NEVER remove dirt sand or other debris from the passenger compart ment by washing it out with a hose Remove dirt with a vacuum cleaner or broom e Never allow waier or other liquids to come in contact with electronic com ponents inside the vehicle as this may damage them Chemicals used for road surface de icing are extremely corrosive They accelerate corrosion and deterioration of underbody components such as the exhaust system fuel and brake lines brake cables floor pan and fenders In winter the underbody must be cleaned periodically For additional protection against rust and corrosion which may be required in some areas consult an authorized NISSAN dealer Appearance and care 7 5 MEMO 7 6 Appearance and care 8 Maintenance and do it yourself Maintenance requirement eeeeeeeeeeeeeeneees 8 2 General Maintenance ecceceeeeeeeeteeeeeeeeteeeeees 8 3 Explanation of general maintenance MCQTMNS 2552 E E 8 3 Maintenance precautions eeeeeeeseeeeeseeeeeneees 8 5 Engine compartment check locations
94. SAL TRANSCEIVER To operate simply press the appropriate button on the HomeLink Universal Trans ceiver The red indicator light illuminates while the signal is being transmitted The effective transmission range of the HomeLink Universal Transceiver may dif fer from your hand held transmitter PROGRAMMING TROUBLE DIAGNOSIS Be sure to keep your original hand held transmitter for possible reprogramming if necessary e Make sure batteries in the hand held transmitter are fully charged e Hold your hand held transmitter against the bottom surface of the HomeLink Universal Transceiver so that you can still see the red indicator light e Hold buttons for duration of the program ming without interruption e Rotate your hand held transmitter end over end and program again For best results place the end opposite the bat tery compartment against the HomeLink Universal Transceiver when programming Instruments and controls 2 37 LED A O O O AIC1070 CLEARING THE PROGRAMMED INFORMATION Should you sell your vehicle be sure to clear the channels of the HomeLink Uni versal Transceiver To clear the channels simultaneously hold down the outside two buttons 1 amp 8 until the red indicator light begins to flash rapidly approximately 20 seconds This will clear all three buttons Individual buttons cannot be cleared but can be reprogrammed at any time by follow ing the programming procedures
95. SSAN dealer or contact DDS Distribution Services Ltd 20770 Westwood Road Strongsville OH 44136 1 800 247 5321 For current pricing and availability of genu ine NISSAN Owner s Manuals for the 2002 Technical and consumer information 9 23 model year and prior see an authorized NISSAN dealer or contact DDS Distribution Services Ltd 20770 Westwood Road Strongsville OH 44136 1 800 247 5321 In Canada To purchase a copy of a Genuine NISSAN Service Manual or Owner s Manual please contact your nearest NISSAN Dealer For the phone number and location of a NISSAN Dealer in your area call the NISSAN Satisfac tion Center at 1 800 387 0122 and a bilingual NISSAN representative will assist you Also available are Genuine NISSAN Service and Owners Manuals for older NISSAN models IN THE EVENT OF A COLLISION Unfortunately accidents do occur In this unlikely event there is some important in formation you should know Many insurance companies routinely autho rize the use of non genuine collision parts in order to cut costs among other reasons Insist on the use of Genuine NISSAN Collision Parts If you want your vehicle to be restored using parts made to NISSAN s original exacting specifications if you want to help it to last and hold its resale value the solution is simple Tell your insurance agent and your repair shop to only use Genuine NISSAN Collision Parts NISSAN does not warrant non NISSAN parts nor
96. The spark ignition system of this vehicle meets all requirements of the Front Canadian Interference Causing Equipment Regulations g T11009 Technical and consumer information 9 7 Model VG33E Drive belts Width x Length in mm Generator belt 0 7008 x 33 66 17 80 x 855 Air conditioner compressor 0 5606 x 46 65 14 24 x 1 185 Power steering pump 0 5606 x 40 74 14 24 x 1 035 9 8 Technical and consumer information WHEELS AND TIRES DIMENSIONS AND WEIGHTS Wheels Steel 5 5 J x15 Overall length in mm 194 8 4 949 Aluminum 6 x16 Overall width in mm 74 9 1 903 Offset in mm 1 77 45 Overall height in mm 67 3 1 710 Tire size Steel P215 70R15 Front tread in mm 63 4 1 610 Aluminum P215 65R16 Rear tread in mm 63 4 1 610 Aluminum P225 60R16 Wheelbase in mm 112 2 2 850 Spare tires T135 90D16 Gross vehicle weight P215 70R15 rating Ib kg Gross axle weight rating See the F M V S S certification label on the left center pillar Front Ib kg Rear Ib kg Technical and consumer information 9 9 WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to travel in another coun try you should first find out if the fuel available is suitable for your vehicle s en gine Using fuel with an octane cetane rating that is too low may cause engine damage All gasoline vehicles must be operated with unleaded gasoline Therefore avoid taking your vehicle to areas w
97. UDIO SYSTEM RADIO Turn the ignition key to ACC or ON and press the power on switch to turn on the radio If you listen to the radio with the engine not running the key should be turned to the ACC position Radio reception is affected by station signal strength distance from radio transmitter buildings bridges mountains and other ex ternal influences Intermittent changes in reception quality normally are caused by these external influences Using a cellular phone in or near the vehicle may influence radio reception quality Radio reception Your NISSAN radio system is equipped with state of the art electronic circuits to en hance radio reception These circuits are designed to extend reception range and to enhance the quality of that reception However there are some general character istics of both FM and AM radio signals that can affect radio reception quality in a mov ing vehicle even when the finest equipment is used These characteristics are com pletely normal in a given reception area and do not indicate any malfunction in your NISSAN radio system Reception conditions will constantly change because of vehicle movement Buildings terrain signal distance and interference from other vehicles can work against ideal reception Described below are some of the factors that can affect your radio reception FM RADIO RECEPTION Range FM range is normally limited to 25 to 30 miles 40 to 48 km with monau
98. When one passenger in the three passenger bench seat would like more leg room one of the second row bucket seats can be removed Seats restraints and supplemental air bag systems 1 25 Seven passenger driving arrangement with third seat in seating position 2 More cargo room When more cargo area room is necessary the three passenger sliding bench seat can be moved to seating position 2 or 3 This seating arrangement provides less leg room for third row passengers but more cargo room Seven passenger driving arrangement with third seat in seating position 3 More cargo room ARS1205 Second row seating removed APD0053 1 26 Seats restraints and supplemental air bag systems If passengers in the three passenger bench seat would like more leg room both second row bucket seats can be removed Passen gers should not be allowed to ride in areas meant for cargo Passengers should always be properly restrained by seat belts Front mats Floor mat positioning pin ARS1216 FLOOR MAT POSITIONS Seven passenger seating Removable floor mats Whenever you remove the mats for any reason the mats must be reinstalled before passengers ride in your vehicle The floor mats are specifically designed to keep objects out of the seat tracks The cargo mat is reversible Floor mat Rear positioning mat pin mat mat ARS1217 Three passenger bench seat in storage positi
99. a rage door opener receiver The exact location and color of the button may vary by garage door opener brand If you have difficulty locating the training button reference your garage door opener manual If you have difficulty programming your garage door opener equipped with a rolling code system to recognize the HomeLink Universal Transceiver with the Rolling Code feature call NISSAN Consumer Affairs Department c Press the training button on the ga rage door opener receiver for 1 to 2 seconds d Return to the HomeLink Universal Transceiver in the vehicle and de press the programmed HomeLink button for the duration of the fast blink on the HomeLink Universal Trans ceiver 1 to 2 seconds Release the button and repress to confirm that the system has trained e Your garage door opener should now recognize your HomeLink Universal Transceiver You may use either your HomeLink Universal Transceiver or your original hand held transmitter to open your garage door IF YOUR VEHICLE IS EVER STOLEN If your vehicle has been stolen you should change the codes of any device that was programmed into the HomeLink Universal Transceiver as soon as possible Consult the owners manual of each device or call the manufacturer or dealer of those devices When your vehicle is recovered you will have to reprogram the HomeLink Uni versal Transceiver with your new trans mitter information FFC Notice This dev
100. a cassette tape Heater air conditioner and audio systems 4 35 CD or the CD changer The radio will go into DUAL PLAY mode and the rear pas sengers can use the rear controls to change media VOLUME button The VOLUME button allows the rear pas sengers to adjust the headphone volume level MEDIA button The MEDIA button allows the rear passen ger to change between AM FM1 FM2 TAPE CD and CD DJ The media options are listed on the faceplate of the rear audio controls When a source of media is se lected that media selection is backlit MEM button In AM FM1 or FM2 mode the MEM button allows the rear passenger to successively access memory preset station 1 through 6 In CD DJ mode the MEM button allows the rear passengers to select other compact discs in the CD changer SEEK button In AM FM1 or FM2 mode the SEEK lt 1 and gt button allows the rear pas sengers to find the next radio station up or down the station band frequency In TAPE mode the SEEK lt and gt button allows the rear passengers use Au tomatic Music Search AMS to find the next or previous song on the cassette In CD mode the SEEK lt and gt button allows the rear passengers to find the next or previous selection on the CD In CD DJ mode the SEEK lt J and gt button allows the rear passengers to find the next or previous selection on the CD For vehicles equipped with the FM AM radio with cassette player when the rea
101. ace the child on the integrated child safety seat Place the belt buckle be tween the child s legs Shoulder belts over child s shoulders Safety belt tongue APD0816 Green in indicator window indicating buckled Safety belt APD0817 tongue 7 Place the left shoulder harness over the child s left shoulder Insert the left shoulder harness tongue into the left side of the belt buckle Confirm that the left shoulder har ness tongue indicator is green The shoul der harness tongues only fit into the proper sides of the belt buckle 8 Place the right shoulder harness over the child s right shoulder Insert the right shoul der harness tongue into the right side of the belt buckle Confirm that the right shoulder harness tongue indicator is green The shoulder harness tongues only fit into the proper sides of the belt buckle Seats restraints and supplemental air bag systems 1 77 Push halves together to fasten chest clip ensure indicator is green Squeeze top and bottom of chest clip to open WRS0093 9 Fasten the two halves of the chest clip and confirm that the chest clip indicator is green Adjust the chest clip slightly lower than the child s shoulders so it comfort ably holds the shoulder harness in positi ton on the child s shoulders amp WARNING e Shoulder harness tongues and chest clips are equipped with visual indica tors to confirm proper an
102. ad to an accident Warm the wind shield with the defroster before you wash the windshield Instruments and controls 2 15 REAR WINDOW WIPER AND WASHER SWITCHES REAR WINDOW DEFOGGER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH Cat cot coy AIC1056 Push and hold the rear washer switch to operate the rear washer The wiper cycles continuously until the switch is released Push the rear wiper switch to operate the wiper The wiper cycles intermittently Push again to cancel A CAUTION e Do not operate the washer continu ously for more than 30 seconds e Do not operate the washer if the reservoir tank is empty 2 16 Instruments and controls To defog the rear window glass start the engine and push the switch on The indica tor light on the switch comes on Push the switch again to turn the defogger off The rear window defogger switch is also used to defrost defog or de ice the power outside heated mirrors if so equipped It automatically turns off in approximately 15 minutes amp CAUTION When cleaning the inner side of the window be careful not to scratch or damage the rear window defogger Headlight switch oO PUSH INTERIOR AIC1073 HEADLIGHT CONTROL SWITCH Lighting Turn the dial to the pa position The front parking side marker tail license plate and instrument lights come on Turn the dial to the 4D
103. ag inflates Right after inflation several air bag system components will be hot Do not touch them you may severely burn yourself No unauthorized changes should be made to any components or wiring of the supplemenial front air bag system This is to prevent accidental inflation of the air bag or damage to the air bag system Do not make unauthorized changes to your vehicle s electrical system suspension system or front end structure This could affect proper operation of the supplemental front air bag system e Tampering with the supplemental front air bag system may result in serious personal injury Tampering includes changes to the steering wheel and the instrument panel as sembly by placing material over the steering wheel pad and above the instrument panel or by installing ad ditional trim material around the air bag system Work around and on the supplemen tal front air bag system should be done by an authorized NISSAN dealer Installation of electrical equipment should also be done by an authorized NISSAN dealer The Supplemental Restraint System SRS wiring should not be modified or disconnected Unauthorized elec trical test equipment and probing devices should not be used on the air bag system A cracked windshield should be re placed immediately by a qualified repair facility A cracked windshield could affect inflation of the supple mental air bag system Seats restraints and supplemental
104. air bag systems 1 35 e The SRS wiring harness connectors are yellow for easy identification When selling your vehicle we request that you inform the buyer about the supplemen tal air bag system and guide the buyer to the appropriate sections in this owner s manual Pre tensioner seat belt system For front seats A WARNING e The pre tensioner seat belt cannot be reused after activation It must be replaced together with the retractor as a unit e If the vehicle becomes involved in a frontal collision but the pre tensioner is not activated be sure to have the pre tensioner system checked and if necessary replaced by your NISSAN dealer e No unauthorized changes should be made to any components or wiring of the pre tensioner seat belt sys tem This is to prevent accidental activation of the pre tensioner seat belt or damage to the pre tensioner seat belt operation Tampering with the pre tensioner seat belt system may result in serious personal in jury e Work around and on the pre tensioner system should be done by an authorized NISSAN dealer Instal lation of electrical equipment should also be done by an authorized NISSAN dealer Unauthorized electri cal test equipment and probing de vices should not be used on the pre tensioner seat belt system e If you need to dispose of the pre tensioner or scrap the vehicle con tact an authorized NISSAN dealer Correct pre tensioner disposal pro cedures ar
105. al injury in an accident or during a sudden stop SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLE MENTAL RESTRAINT SYSTEM This supplemental restraint system descrip tion contains important information concern ing the driver and passenger supplemental front air bags The supplemental restraint system air bags can help reduce impact force to the driver and front passenger in certain frontal collisions The supplemental air bags are designed to supplement the crash protection provided by the seat belts and are not a substitute for the seat belts The seat belts should always be correctly worn and the driver and front passenger seated a suitable distance from the steering wheel and instrument panel See Seat belts and Precautions on seat belt usage later in this section for details The supplemental air bags operate only when the ignition switch is in the ON or START position After turning the ignition key to the ON position the supplemental air bag warn ing light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is opera tional A WARNING The supplemental front air bag ordi narily will not inflate in the event of a side impact rear impact roll over or lower severity frontal collision Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents The seat belts and the supplemental front air bag are
106. al times When brake pedal movement distance of travel remains the same from one pedal application to the next continue on to the next step 2 While depressing the brake pedal start the engine The pedal height should drop a little 3 With the brake pedal depressed turn the engine off Keep the pedal depressed for about 30 seconds the pedal height should not change 4 Run the engine for one minute without depressing the brake pedal then turn it off Depress the brake pedal several times The pedal travel distance will de 8 22 Maintenance and do it yourself crease gradually with each depression as the vacuum is released from the booster If the brakes do not operate properly see an authorized NISSAN dealer FUSES Fuse and relay box ENGINE COMPARTMENT CAUTION Never use a fuse of a higher amperage rating than that specified on the fuse box cover This could damage the elec trical system or cause a fire If a headlight does not come on check for an open fuse The left headlight driver s side and right headlight passenger side fuses are lo cated in the left hand fuse box near the radiator cap 1 Turn the headlight switch to the OFF position 2 Open the engine hood 3 Remove the fuse box cover 4 Remove the fuse with the fuse puller attached to the passenger compartment fuse box cover 5 I
107. all cargo to help pre vent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or collision unsecured cargo could cause per sonal injury Technical and consumer information 9 13 e Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs If you do parts of your vehicle can break tire damage could occur or it can change the way your vehicle handles This could re sult in loss of control and cause per sonal injury e Overloading can shorten the life of the vehicle Failures caused by over loading are not covered by the vehi cle s warranty TOWING A TRAILER Total trailer load Tongue load PA G Tongue load Total trailer load x 100 9 to 11 T11011M Your new vehicle was designed to be used primarily to carry passengers and cargo Remember that towing a trailer places ad ditional loads on your vehicle s engine drive train steering braking and other systems A NISSAN Trailer Towing Guide U S only contains information on your vehicle s trailer towing ability and the special equipment required and may be obtained from an authorized NISSAN dealer Do not tow a trailer if your vehicle is a cargo van model 9 14 Technical and consumer information MAXIMUM LOAD LIMTS Maximum trailer loads Never allow the total trailer load to exceed 3 500 Ibs 1 588 kg The total trailer
108. anchors ARS1141 Seats restraints and supplemental air bag systems 1 15 Removing the second row driver side bucket seat FOLD seat back down LIFT up the recliner 6 SLIDE seat backward to release it from floor anchors ARS1143 PULL straps to release floor latch levers 3 Unlock the seat legs at the two rear floor latch levers by pulling up on the two straps 4 Lift the back of the seat and slide it rearward off the front anchor positions 1 16 Seats restraints and supplemental air bag systems Installing the second row bucket seats G PUSH seat down Installing the second row bucket seats Clean the area around the seat leg floor anchors before installing the seat 1 With the seatback fully folded place the seat behind the floor anchors and slide seat leg hooks so they catch into each floor anchor 2 Push down on the rear of the seat to secure the two rear floor latches 3 Lift the recliner lever and raise the seat back POSITION seat leg hooks ARS1142 4 Rock the seat back and forth to be sure it is securely latched The second row bucket seats are not interchangeable If you are having diffi culty installing the seats you may have them in the wrong location Forward and backward Seat adjustment ARS1144 Second row passenger side bucket seat The bucket seat near the passenger side sliding door can be m
109. and vehicle handling Tire pressure should be Maintenance and do it yourself 8 31 checked when tires are COLD Tires are considered COLD after the vehicle has been parked for three or more hours or driven less than 1 mile 1 6 km COLD tire pressures are shown on the tire placard affixed to the inside of the glove box amp WARNING Improperly inflated tires can fail sud denly and cause an accident The vehicle capacity weight is indi cated on the tire placard Do not load your vehicle beyond this capacity Overloading your vehicle may result in reduced tire life unsafe operating conditions due to premature tire fail ure or unfavorable handling charac teristics and could also lead to a serious accident Loading beyond the specified capacity may also re sult in failure of other vehicle com ponents Before taking a long trip or whenever you have loaded your vehicle heavily use a tire pressure gauge to ensure that the tire pressures are at the specified level 8 32 Maintenance and do it yourself e Do not drive your vehicle over 85 MPH 140 km h unless it is equipped with high speed rated tires Driving faster than 85 MPH 140 km h may result in tire failure loss of control and possible injury e For additional information regarding tires refer to Important Tire Safety Information in the Warranty Infor mation Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Inform
110. and a door is open Pre driving checks and adjustments 3 3 Driver side sliding door LOCK Door lock rocker switch Inside sliding door handle Sliding door To lock a sliding door from inside the ve hicle press the door lock rocker switch on the side marked L To unlock press the rocker switch on the side marked U The driver side sliding door cannot be fully opened when the fuel door is open 3 4 Pre driving checks and adjustments UNLOCK UNLOCK LOCK Passenger side sliding door Door lock rocker switch Inside sliding door handle APD1055 Driver side Door lock switch UNLOCK o1 LOCKING WITH POWER DOOR LOCK SWITCH Operating the lock unlock switch locks or unlocks all doors If the power door lock switch is pressed when a sliding door is open the sliding door automatically locks when it is closed Passenger side OIN APD1075 Passenger side sliding door Driver side sliding door WHEN DOOR WiLL ae NOT ee OPEN FROM W INSIDE i as Child lock eRe Child lock we knob PAS S OUVRI knob L INTERIEUR m RSi A oo POUSSER a a O O jo Lock e E lt 7 POUR E D A VERROUILLER N K CHILD LOCK SY SECURITE ENFANTS Vn APD1056 CHILD SAFETY SLIDING DOOR When the lever is in the LOCK position LOCKS the sliding doors can be opened only from the outside er
111. aning COMPACT LHA0099 Compact Disc CD Player e Only use high quality 4 7 inches 12 cm round discs that have the COM PACT disc DIGITAL AUDIO logo on the disc or packaging Heater air conditioner and audio systems 4 17 During cold weather or rainy days the player may malfunction due to the humidity If this occurs remove the CD and dehumidify or ventilate the player completely The player may skip while driving on rough roads The CD player sometimes cannot function when the compartment tem perature is extremely high Decrease the temperature before use Do not expose the CD to direct sun light CDs that are of poor quality dirty scratched covered with fingerprints or that have pin holes may not work properly Do not use the following CDs as they may cause the CD player to malfunc tion e 8 cm 3 1 in discs with an adapter e Recordable compact discs CD R e Rewritable compact discs CD RW e CDs that are not round e CDs with a paper label e CDs that are warped scratched or have abnormal edges 4 18 Heater air conditioner and audio systems 21 20 eT _ sem 19 ant lt sek gt 2 TUNE gt scan auro 18 17 16 15 14 13 12 11 Eh Hoppop ww N OOAON OOO f O i i wo PhP WHAO138 46 15 FM
112. ar combination light High mounted stop light License plate light Luggage light Back up light compartment WDI0059 ADI1093 8 28 Maintenance and do it yourself Replacement procedures All lights except for headlights are either type A B C or D When replacing a bulb first remove the lens and or cover Rear combination light Stop tail light Back up light Steplight PRY UP PULL to Type D to remove remove E Type C Side marker light WDI0062 Maintenance and do it yourself 8 29 Front turn signal light Front combination light t Headlight FRONT Coolant reservoir oa Cobie PRY up to remove ADI1096 8 30 Maintenance and do it yourself WHEELS AND TIRES Luggage compartment light PRY UP to remove Interior light PRY UP to remove ADI1095 Max inflation pressure DI1033M TIRE PRESSURE If you have a flat tire see the In case of emergency section of this manual Maximum inflation pressure Do not exceed the maximum inflation pres sure shown on the side wall of the tire Tire inflation pressure Check the tire pressure including the spare at least once a month and always prior to long distance trips Incorrect tire pressure may adversely affect tire life
113. as a grommet which is placed over the floor mat positioning bracket lo cated at the base of the driver s seat Push the positioning pins into the seat tracks to ensure correct installation then straighten the mats as necessary The step mats have holes in addition to pins When the mats are arranged properly the positioning pins of the two mats on either side of each step mat should fit through the holes in the step mats and into the seat track amp WARNING e Do not allow passengers to use seats placed in storage positions because the seat belts will not pro tect the occupants Be sure to use the proper seat belts for each seat location Improper seat belt usage will increase the risk of severe injury in an accident e It is extremely dangerous to ride ina cargo area inside of a vehicle In a collision people riding in these ar eas are more likely to be seriously injured or killed 1 30 Seats restraints and supplemental air bag systems Properly secure all cargo to help prevent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or collision unsecured cargo could cause per sonal injury Do not allow people to ride in any area of the vehicle that is not equipped with seats and seat belts Be sure everyone in your vehicle is in a seat and is using a seat belt properly Failure to follow proper seating in structions in this section could re sult in serious person
114. aska contact a NISSAN dealership for more information regarding suitable fluids including recommended brand s of Dexron III Mercon Automatic Transmission Fluid 5 6 7 9 2 Technical and consumer information Available in mainland U S A through an authorized NISSAN dealer For further details see Air conditioner specification label For further details see Changing engine oil FUEL RECOMMENDATION Your vehicle is designed to operate on unleaded gasoline with an octane rating of at least 87 AKI Anti Knock Index number Research octane number 91 CAUTION e Using a fuel other than that specified could adversely affect the emission control system and may also affect warranty coverage e Under no circumstances should a leaded gasoline be used since this will damage the three way catalyst Reformulated gasoline Some fuel suppliers are now producing re formulated gasolines These gasolines are specially designed to reduce vehicle emis sions NISSAN supports efforts towards cleaner air and suggests that you use refor mulated gasoline when available Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxygenates such as ethanol MTBE and methanol with or without advertising their presence NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel compatibility for your vehicle cannot be readily determined If in doubt ask your servic
115. ation booklet Canada TYPES OF TIRES A WARNING When changing or replacing tires be sure all four tires are of the same type i e summer all season or snow and construction An authorized NISSAN dealer may be able to help you with information about tire type size speed rating and availability Replacement tires may have a lower speed rating than the factory equipped tires and may not match the potential maximum vehicle speed Never exceed the maxi mum speed rating of the tire e For additional information regarding tires refer to Important Tire Safety Information in the Warranty Infor mation Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Information booklet Canada All season tires NISSAN specifies All Season tires to pro vide good performance all year including snowy and icy road conditions All Season Tires are identified by ALL SEASON and or M amp S on the tire sidewall Snow tires have better snow traction than All Season tires and may be more appropriate in some areas Snow tires If snow tires are needed it is necessary to select tires equivalent in size and load rating to the original equipment tires If you do not it can adversely affect the safety and han dling of your vehicle Generally snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed Never exceed the maximum spe
116. ation or the antenna rod may break during vehicle operation AUTOVISION FAMILY ENTERTAINMENT SYSTEM FES if so equipped 07 a oe afr e ey LHA0088 A WARNING e The Autovision Family Entertain ment System FES is designed for rear seat passenger viewing only e The driver must not attempt to oper ate the FES while the vehicle is in motion so that full attention may be given to vehicle operation CAUTION The glass screen on the liquid crys tal display may break if hit with a hard or sharp object If the glass breaks do not touch the liquid crys talline material which contains a small amount of mercury In case of contact with skin wash immediately with soap and water Avoid pinching fingers when remov ing and reinstalling the player Do not insert foreign objects into the video player To prevent damage when reinstall ing the player be sure of proper alignment when inserting Do not force Use a damp soft cloth when clean ing the Autovision Family Enter tainment System components Do not use solvents or cleaning solu tions Do not attempt to use the system in extreme temperature conditions be low 30 or above 113 F Heater air conditioner and audio systems 4 37 e To avoid draining the vehicle bat tery do not operate the system more Power Play Fast Forward Headphone button button button Volume Control tha
117. ay be under pressure Turn the cap one half turn and wait for any hissing sound to stop to prevent fuel from spraying out and possibly causing personal injury Then re move the cap e Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically Continued refuel ing may cause fuel overflow result ing in fuel spray and possibly a fire e Use only an original equipment type fuel filler cap as a replacement It has a built in safety valve needed for proper operation of the fuel system and emission control system An incorrect cap can result in a serious malfunction and possible injury Never pour fuel into the throttle body to attempt to start your vehicle CAUTION If fuel is spilled on the vehicle body flush it away with water to avoid paint damage Tighten until the fuel filler cap clicks Failure to tighten the fuel filler cap properly may cause the fone mal function indicator lamp MIL to illu minate If the enf lamp illuminates because the fuel filler cap is loose or missing tighten or install the cap and continue to drive the vehicle The n lamp should turn off after a few driving trips If the one lamp does not turn off after a few driving trips have the vehicle inspected by an authorized NISSAN dealer For additional information see the Malfunction indicator lamp MIL in the Instrument and controls section earlier in this manual STEERING WHEE
118. aying a metal or chrome tape TAPE EJECT Push the EJ button The cassette tape automatically comes out VOL PUSH ON i 16 15 14 13 12 11 10 WHA0139 2 3 4 5 6 7 8 9 1 0 11 12 13 14 15 16 17 18 19 20 VOLUME ON OFF control CD eject button MUTE button Tape eject button TAPE CD select button AUTO SET button if so equipped CLOCK button BALANCE FADE select button SHUFFLE station memory 6 button COMPRESSION station memory 5 button BASS TREBLE BALANCE FADE control button Dolby station memory 4 button Tape reverse station memory 3 button BASS TREBLE select button FAST FORWARD station memory 2 button REWIND station memory 1 button SCAN button TUNE button SEEK button AM FM select button Heater air conditioner and audio systems 4 25 FM AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC CD PLAYER Audio main operation To turn the radio on turn the ignition key to ACC or ON If you listen to the radio with the engine not running turn the key to the ACC position Radio reception is affected by station signal strength distance from radio transmitter buildings bridges mountains and other external influences Intermittent changes in reception quality normally are caused by external influences Using a cellu
119. be secured with the seat belt clip The seat belt clip should not be used with a child seat or during seat belt usage The seat belt clip opening should face the front of the vehicle PRESS release button to detach tongue from buckle ARS1126 A twisted belt may prevent the retractor from working properly If the two buckle seat belt system is twisted disengage the single window tongue from the auxiliary buckle on the side of the seat remove the twist and reinstall the tongue into the auxiliary buckle until you hear a snap and feel the latch engage Both tongues must be attached to their appropriate buckles whenever someone is riding in that seating position If the tongues are released to allow a third row passenger to enter or exit the tongues must be reattached Seats restraints and supplemental air bag systems 1 47 When the two passenger bench seat is re moved from the vehicle you must detach the single window tongue from the auxiliary buckle When the three passenger bench seat is moved up to the second row position the passenger seated near the passenger side sliding door needs to use the double window tongue and the standard buckle only Because the three passenger bench seat is wider and closer to the passenger side sliding door the single window seat belt tongue and the auxiliary buckle are not necessary S Auxiliary buckle STEP OVER seat belt when exiting from third row seat ARS112
120. bricant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner system components The refrigerant HFC 134a R 134a in your NISSAN vehicle does not harm the earth s ozone layer Although this refrigerant does not affect the earth s atmosphere certain government regulations require the recov ery and recycling of any refrigerant during automative air conditioning system service An authorized NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioning system refrigerant Contact an authorized NISSAN dealer when servicing your air conditioning system SPECIFICATIONS ENGINE Model VG33E Type Gasoline 4 cycle Cylinder arrangement 6cylinder V slanted at 60 Bore x Stroke in mm 3 602 x 3 274 91 5 x 83 0 Displacement cu in cm 199 84 3 275 Firing order 1 2 3 4 5 6 See illustration below Idle speed rpm Ignition timing degree B T D C at idle speed degree rpm See the Important Vehicle Information label on the underside of the hood CO percentage at idle speed No air Spark plug Hot PFR4G 11 Standard PFR5G 11 Cold PFR6G 11 Spark plug gap Nominal 0 043 in 1 1mm Camshaft operation Timing belt See note below Gylinder number NOTE Periodic maintenance is necessary Refer to the appropriate periodic A maintenance schedule in the NISSAN Service and Maintenance Q Guide LA
121. buckle FLEXIBLE SEATING Removing the second row bench seat A WARNING e Do not remove or install seats while the vehicle is moving e After adjustment gently rock in the seat to make sure it is securely locked e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly See Precautions on seat belt usage later in this section 1 12 Seats restraints and supplemental air bag systems oe Slide seat backward to release from floor anchors ARS1139 e When adjusting or moving any of the seats in your vehicle do not use any of the seat belt buckles tongues or webbing to carry or move the seats Lifting the seats by any of the seat belts could damage them Damaged seat belts should be replaced at an authorized NISSAN dealer Failure to follow these instructions could in crease the chance and or severity of injury in an accident CAUTION e The seats are heavy Two people should remove or install them e Do not sit in seats that have been removed from the vehicle They may tip over and you cou
122. cal and consumer in formation section of this manual for wheel off set dimensions Do not install a deformed wheel or tire even if it has been repaired Such wheels or tires could have structural damage and could fail without warn ing e The use of retread tires is not recom mended e For additional information regarding tires refer to Important Tire Safety Information in the Warranty Infor mation Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Information booklet Canada Wheel balance Unbalanced wheels may affect vehicle han dling and tire life Even with regular use wheels can get out of balance Therefore they should be balanced as required Wheel balance service should be performed with the wheels off the vehicle Spin balanc ing the front wheels on the vehicle could lead to transmission damage e For additional information regarding tires refer to Important Tire Safety Informa tion in the Warranty Information Booklet US or Tire Safety Information in the Warranty and Roadside Assistance Infor mation booklet Canada Care of wheels e Wash the wheels when washing the ve hicle to maintain their appearance e Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed e Do not use abrasive cleaners when washing the wheels Inspect wheel rims regularly for dents or corrosion Such damage may
123. cause loss of pressure or poor seal at the tire bead e NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter Spare tire TEMPORARY USE ONLY spare tire US only Canadian vehicles are equipped with a full size spare tire Observe the following precautions if the TEMPORARY USE ONLY spare tire must be used other wise your vehicle could be damaged or involved in an accident Maintenance and do it yourself 8 35 A WARNING e The spare tire should be used only for emergency use only It should be replaced by the standard tire at the first opportunity to avoid possible tire or diffential damage e Drive carefully while the TEMPO RARY USE ONLY spare tire is in stalled Avoid sharp turns and abrupt braking while driving e Periodically check spare tire infla tion pressure Always keep the pres sure of the TEMPORARY USE ONLY spare tire at 60 psi 420 kP 4 2 bar Always keep the pressure of the full size spare tire if so equipped at the recommended pressure for standard tires as indicated on the tire placard For tire placard location see Tire placard in the index of this manual e With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 mph 80 km h 8 36 Maintenance and do it yourself When driving on roads covered with snow or ice the TEMPORARY USE ONLY spare tire should be used on the rear wheel and
124. ch to turn the overdrive on The O D OFF indicator light goes out Remember not to drive at high speeds for extended periods of time with the O D OFF light illuminated This reduces the fuel economy PARKING BRAKE A WARNING e Be sure the parking brake is fully released before driving Failure to do so can cause brake failure and lead to an accident e Do not release the parking brake from outside the vehicle e Do not use the gear shift in place of the parking brake When parking be sure the parking brake is fully en gaged e Do not leave children unattended ina vehicle They could release the park ing brake and cause an accident PUSH to set amp parking brake again to release parking PUSH brake ASD1017 To engage Firmly depress the parking brake To release 1 Firmly apply the brake pedal 2 Move the shift selector lever to the P Park position 3 Press and release the parking brake completely 4 Before driving be sure the brake warning light goes out Starting and driving 5 9 CRUISE CONTROL PRECAUTIONS ON CRUISE CONTROL e Ifthe cruise control system malfunctions it cancels automatically The SET indica tor light in the instrument panel then blinks to warn the driver e f the SET indicator light blinks turn the CRUISE main switch OFF and have the system checked by an authorized NISSAN dealer e The SET indicator light in the instrument panel
125. cle is the prod uct of a successful worldwide company that manufactures cars and trucks in over 17 coun tries and distributes them in 170 nations NISSAN vehicles are designed and manufactured by Nissan Motor Co Ltd which was founded in Tokyo Japan in 1933 and NISSAN affiliates world wide collectively growing to become the fifth largest automaker in the world In addition to cars and trucks NISSAN also makes forklift trucks marine engines boats and other diversified products NISSAN has made a substantial and growing investment in North America NISSAN s commit ment is nearly 4 billion dollars in capital invest ments in facilities across the continent Some of the facilities include the Nissan Manufacturing facility in Smyrna Tennessee vehicle styling design at Nissan Design America Inc in San Diego California and engineering at Nissan Technical Center North America in Farmington Hills Michigan Additionally NISSAN employs nearly 18 000 people throughout the United States Canada and Mexico An additional 71 000 people work for the 1 500 NISSAN and INFINITI dealers across North America NISSAN is also a substantial contributor to the Canadian economy Nissan Canada Inc its sup pliers and over 140 dealers employ approxi mately 4 500 people These include company employees and the staffs of NISSAN dealers all across Canada In addition many Canadians work for companies that supply NISSAN and NISSAN dealers wit
126. close and adjust the air flow direction of ventilators of ventilators XJ This symbol indicates a vent is closed when the vent switch is moved down This symbol indicates a vent is open when the vent switch is moved up 4 2 Heater air conditioner and audio systems HEATER AND AIR CONDITIONER manual amp WARNING e The air conditioner cooling function Temperate control dial Air flaw control dial Ppa only when the engine is eee ee g m SN Gi unning ee eee i aN e Do not leave children impaired i max B adults or pets alone in your vehicle Ce On hot sunny days temperatures in a closed vehicle could quickly be Rear seat A C fan dome we come high enough to cause severe control if so a i or possibly fatal injuries to people or equipped i aoa k animals Do not use the recirculation mode Air conditioner Button WAROO for long periods as it may cause the interior air to become stale and the CONTROLS av Air flows mainly from the front and windows to fog up rear foot outlets e Positioning of the heater and air con Fan control dial Air flows from defroster outlets and ditioner controls should not be done This dial controls fan speed the front and rear foot outlets while driving so full attention may j be given to vehicle operation Air flow control dial WV Air flows mainly from defroster outlets This dial allows you to select the air flow MAX Air f
127. commendations Some fabric protectors contain chemicals that may stain or bleach the seat material Use a cloth dampened only with water to clean the meter and gauge lens A CAUTION e Never use benzine thinner or any similar material e Leather seats should be regularly coated with a leather wax like saddle soap Never use car wax e Never use fabric protectors unless recommended by the manufacturer e Do not use glass or plastic cleaner on meter or gauge lens covers It may damage the lens cover Appearance and care 7 3 FLOOR MATS The use of genuine NISSAN floor mats can extend the life of your vehicle carpet and make it easier to clean the interior No matter what mats are used be sure they are fitted for your vehicle and are prop erly positioned in the footwell to prevent interference with pedal operation Mats should be maintained with regular cleaning and replaced if they become excessively worn Front floor mat positioning aid Driver side only This model includes a front floor mat bracket to act as a floor mat positioning aid NISSAN floor mats specially designed for your vehicle incorporate grommets To in stall simply position the mat using the floor mat bracket hook through the floor mat grommet hole while centering the mat in the footwell Periodically check to make certain the mat is properly positioned SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mi
128. cumstances please note that the transmission will remain in 3rd gear NOTE If the vehicle is driven under extreme conditions such as excessive wheel spinning and subsequent hard braking the Fail safe system may be activated This will occur even if all electrical circuits are functioning properly In this case turn the ignition key OFF and wait for 3 seconds Then turn the key back to the ON position The vehicle should return to its normal operating condition If it does not re turn to its normal operating condition have an authorized NISSAN dealer check the trans mission and repair if necessary Sele 0 Cea PUSH off on ASD0561 Overdrive switch Each time your vehicle is started the trans mission is automatically reset to overdrive ON ON For normal driving the overdrive switch is engaged The transmission is upshifted into overdrive as the vehicle speed increases Overdrive 4th gear does not engage until the engine has reached operating temperature OFF For driving up and down long slopes where engine braking is necessary push the overdrive switch once The O D OFF indicator light illuminates at this time When cruising at a low speed or climbing a gentle slope you may feel uncomfortable shift shocks as the transmission shifts be tween 3rd gear and overdrive repeatedly In this case press the overdrive switch When driving conditions change press the overdrive swit
129. d restraint supports WRS0022 To attach a tether strap to a third row bench seat 1 For the passenger driver side outboard seating positions route the tether strap under the head restraint and between the head restraint supports For the center seating position route the tether strap over the seatback Third row bench seat Tether strap anchor brackets WRS0092 2 Hook the tether strap into the slot in the anchor bracket that is located on the lower back of the seat 3 4 Third row child restraint placement Tether strap Tongue and buckle fastened WRS0024 Tighten the tether strap to remove any slack Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure it is securely held in place Check to make sure the child restraint is properly secured prior to each use If it is not secure repeat steps two through four INTEGRATED CHILD SAFETY SEATS if so equipped amp WARNING e Failure to follow the instructions for the use of these integrated child safety seats can result in your child striking the vehicle s interior during a sudden stop or crash causing the injury or death of your child e Improper use of a child restraint can increase the risk or severity of injury for both the child and other occu pants of the vehicle All U S states and Canadian provinces re
130. d safety seat Storing the Integrated Child Safety Seat 1 Be sure the shoulder harnesses are fully retracted and resting inside the inte grated child safety seat recess It is not necessary to reconnect the shoulder har nesses and belt buckle prior to storing the integrated child safety seat 2 While holding onto but not pulling the cushion release strap rotate the cushion upward until it fits flush with the second row seat back cushion and locks into position 3 Be sure the integrated child safety seat is locked in the stowed position by grasping the safety seat cushion and attempting to lower it without pulling the cushion re lease strap If the integrated child safety seat is not locked in the stowed position repeat steps one through three Integrated Child Safety Seat main tenance e To clean the shoulder harnesses and belt buckle webbing apply a mild soap solu tion or any solution recommended for cleaning upholstery or carpets Then brush the webbing wipe it with a cloth and allow it to dry in the shade Do not allow the shoulder harnesses to retract until they are completely dry e The integrated child safety seats cloth removable pads may be cleaned with mild soap and water The cloth remov able pads are attached to the seats with fastener strips and may be easily re moved The pads are machine washable Fo best results machine wash in cold water in the gentle cycle Tumble dry on low heat Do not us
131. d secure latching For the safety of the child and occupants of the vehicle all indi 10 Pull shoulder belt out fully to activate automatic locking mode APD0819 cators must show green before oper ating the vehicle If the shoulder harness is unfas tened or not fastened properly the child could be seriously injured Grasp the right shoulder harness above the chest clip and pull until the harness fully extends and a click is heard At this time the harness retractor is in the automatic locking mode child restraint mode With the child sitting properly straight up and back in the integrated 1 78 Seats restraints and supplemental air bag systems 11 child safety seat allow the right shoul der harness to retract over the right shoulder and securely restrain the child A clicking sound is heard as the har ness retracts indicating that the retrac tor is in the automatic locking mode Be sure the left shoulder harness is also properly positioned over the child s left shoulder Check that the shoulder harness is in the automatic locking mode by trying to pull the shoulder harness out of the retractor If you cannot pull any of the shoulder harness webbing out of the retractor the shoulder harness is in the automatic locking mode If the shoulder harness is not locked repeat step 10 If after repeated attempts the integrated child safety seat shoulder harness can not be placed in the auto
132. d to two anchors located at certain seating positions in your vehicle This sys tem is known as the LATCH Lower An chors and Tether for Children system This system may also be referred to as the ISOFIX or ISOFIX compatible system With this system you do not have to use a vehicle seat belt to secure the child re straint Your vehicle is equipped with spe cial anchor points that are used with LATCH system compatible child restraints Check your child restraint for a label stating that it is compatible with the LATCH system This information may also be in the child restraint owner s manual If you have such a child restraint refer to the illustration for the rear seating positions equipped with LATCH system anchors which can be used to se cure the child restraint Seats restraints and supplemental air bag systems 1 67 The LATCH system anchors are located at the rear of the seat cushion near the seat back A label is attached to the seatback to help you locate the LATCH system anchors Some child restraints may also require the use of a top tether strap See Top Tether Strap Child Restraint later in this section for installation instructions When installing a child restraint carefully read and follow the instructions in this manual and those supplied with the child restraint When you install a LATCH system compat ible child restraint with lower anchor attach ments in the rear seat follow these steps WA
133. de of the vehicle or to dehumidify the air inside the vehicle A C Activate the air conditioner in any of the override modes listed above by pressing the A C button The A C indicator light comes on to verify activation and cooled air flows from the vents Fan speed continues to be controlled by the EATC unless the fan speed thumbwheel is used to override AHA1143 English metric mode Switch from English to metric temperature display by simultaneously pressing the Gy and A C buttons and holding the thumbwheel in upper position HI for one second A WARNING Do not switch temperature displays while driving so full attention may be given to vehicle operation Heater air conditioner and audio systems 4 13 REAR SEAT AIR CONDITIONER if so equipped a a Se F Fan control Temperature Air flow control Rear seat A C control dial control dial dial lt u err i wa ne S BP S OFF REAR A C 1 2 s a l Fan control dial Rear seat A C fan control button To operate the rear seat air conditioner the engine must be running The rear seat air conditioner can be turned on and off from the front controls If the rear seat fan control lever on the front panel is set to OFF the rear air conditioner is turned off If it
134. does NISSAN s warranty apply to damage caused by a non genuine part Using Genuine NISSAN Parts can help pro tect your personal safety preserve your warranty protection and maintain the resale value of your vehicle And if your vehicle was leased using Genuine NISSAN Parts may prevent or limit unnecessary excess wear and tear expenses at the end of your lease NISSAN designs its hoods with crumple zones to minimize the risk that the hood will penetrate the windshield of your vehicle in an accident Non genuine imitation parts may not provide such built in safeguards Also non genuine parts often show prema ture wear rust and corrosion 9 24 Technical and consumer information Why should you take a chance In over 40 states the law says you must be advised if non genuine parts are used to repair your vehicle And some states have enacted laws that restrict insurance compa nies from authorizing the use of non genuine collision parts during the new ve hicle warranty These laws help protect you so you can take action to protect yourself It s your right If you should need further information visit us at www nissandriven com 10 Index Accident Inertia fuel shut off switch 08 6 11 After an accident Air bag See supplemental restraint SVSUGIM ssicsiccsencoashesaisinadecssisssdinssaeteedssszesnossy 1 31 Air bag warning light ie UBL Air cleaner housing filter 8 17 Air cond
135. duction Push the DO button for Dolby NR encoded tapes to reduce high frequency tape noise When activated a DO appears in the dis play window Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora 4 30 Heater air conditioner and audio systems tion Dolby NR and the double D symbol are trademarks of Dolby Laboratories Li censing Corporation AMS Automatic Music Search Pushing the seek button while playing a cassette tape activates the Automatic Music Search AMS mode Press lt SEEK to rewind the tape to the previous selection or press SEEK to forward the tape to the nest selection This system searches for the blank intervals between selections If there is a blank inter val within one program or there is no interval between programs the system may not stop in the desired or expected location Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome tape TAPE EJECT Push the EJ button The cassette tape automatically come out Compact Disc CD player opera tion Turn the ignition key to the ACC or ON position and carefully insert the compact disc into the slot with the label side up The compact disc is automatically pulled into the slot and starts to play If the radio or cassette tape is already operating it automatically turns off and the compact disc begins to play A CAUTION Do not f
136. e J1819 for child seat installation 3 If the child restraint is compatible with your vehicle place your child in the child restraint and check the various adjust ments to be sure the child restraint is compatible with your child Always follow all recommended procedures All U S states and some provinces or territories of Canada require that infants and small children be restrained in ap proved child restraints at all times while the vehicle is being operated amp WARNING e Improper use of a child restraint can result in increased injuries for both the infant or child and other occu pants in the vehicle Follow all of the child restraint manufacturer s instructions for in stallation and use When purchasing a child restraint be sure to select one which will fit your child and vehicle It may not be possible to properly install some types of child restraints in your vehicle If the child restraint is not anchored properly the risk of a child being injured in a collision or a sudden stop greatly increases Adjustable seatbacks should be po sitioned to fit the child restraint but as upright as possible After attaching the child restraint test it before you place the child in it Tilt it from side to side Try to tug it forward and check to see if the belt holds the restraint in place If the restraint is not secure tighten the belt as necessary or put the re straint in another seat and test it again
137. e Safety Information in the Warranty and Roadside Assistance Infor mation booklet Canada Windshield Clean the windshield on a regular basis Check the windshield at least every six months for cracks or other dam age Have a damaged windshield repaired by a qualified repair facility Windshield wiper blades Check for cracks or wear if they do not wipe properly Doors and hood Check that all doors and the hood operate properly Also ensure that all latches lock securely Lubricate hinges latches rollers and links if necessary Make sure the secondary latch keeps the hood from opening when the primary latch is released When driving in areas using road salt or other corrosive materials check lubrication frequently Lights Clean the headlights on a regular basis Make sure the headlights stop lights tail lights turn signal lights and other lights are all operating properly and installed se curely Also check headlight aim Inside the vehicle The maintenance items listed here should be checked on a regular basis such as when performing periodic maintenance cleaning the vehicle etc Additional information on the following items with an is found later in this section Maintenance and do it yourself 8 3 Warning lights and chimes Make sure all warning lights and chimes are operating properly Windshield wiper and washer Check that the wipers and washer operate properly and that the wipers do
138. e chlorine bleach and do not dry clean CAUTION Failure to follow the washing instruc tions provided on the cloth removable pads may result in premature wear or damage Seats restraints and supplemental air bag systems 1 79 e Periodically inspect the belt and metal components of the integrated child safety seats such as the buckles tongues shoulder harness webbings and latching indicators Periodically check the func tion of the integrated child safety seat shoulder harness retractor functions If loose parts deterioration cuts frays malfunctions or other damage to the belt webbings or metal parts are found see an authorized NISSAN dealer for repairs Inspection after an accident If your vehicle was involved in an accident before using the integrated child safety seats all related components should be inspected for damage by an authorized NISSAN dealer Damage to the integrated child safety seat or related components must be repaired 1 80 Seats restraints and supplemental air bag systems MEMO Seats restraints and supplemental air bag systems 1 81 2 Instruments and controls Meters and Gauges srmn 2 4 Speedometer and odometer cccceeee 2 5 Tachometer ssiru 2 5 Engine coolant temperature gauge 2 6 Fuel GAUGE ese neice cetanetenstbsee cede cnesstcecteeenevecnte chase 2 6 Message center if so equipped eee 2 7 Warning indicator lights and audible FOMIN
139. e fan speed to the existing conditions To control the fan speed yourself use the thumbwheel located at the extreme right side of the EATC control panel Using the thumbwheel cancels the automatic fan speed control and causes a to appear in the display window Rotate the thumbwheel up for HI speeds and down for LO speeds To return to auto fan control press the AUTOMATIC button Air flow control Your EATC has five buttons which allow you to make special selections The buttons are 4 12 Heater air conditioner and audio systems grouped in the middle of the EATC panel and allow you to determine airflow location Pressing any of the air control buttons changes airflow location only and does not affect the ability of the system to control temperature or fan speed Return to fully automatic operation by pushing the AUTO MATIC button 4 Push this button for airflow to the front and rear floor outlets and windshield at the same time The 37 indicator light comes on and the display window shows the set tem perature W Push this button to obtain maximum airflow to the windshield Adjust the temperature setting as required for defrosting The Gy indicator light comes on and the display window shows the set temperature When the outside temperature is about 45 F 7 C or above the air is dehumidified to prevent window fogging gt Push this button to select airflow through
140. e housing to store when not in use Ensure that the screen is latched securely into the housing when stored Playing a videocassette tape CAUTION e Donot insert foreign objects into the VCP e Only operate the VCP while the ve hicle engine is running Operating the VCP for extended periods of time with the engine OFF can discharge the vehicle battery e Do not leave a videocassette tape in the VCP for extended periods of time The FES is automatically activated when the vehicle ignition and radio are both ON Open the floor console and insert the video cassette tape into the Video Cassette Player VCP The videocassette tape will start to play automatically e The system will not allow a videocas sette to be inserted in the wrong position 4 40 Heater air conditioner and audio systems e The VCP and floor console covers should remain closed when the video cassette is playing e When the ignition is turned ON audio is set to low volume through the head phones Press the VOLUME button on the RSEM to increase the volume To listen through the vehicle s speaker sys tem press the speaker control button To remove the videocassette tape press the STOP button and then press the EJECT button When the engine is turned OFF the videocassette tape is automatically ejected from the VCP To play a video game 1 Connect the video line from your video game device to the VIDEO jack 2 Connect the audio cab
141. e no stations in the area that are transmitting that type of programming Cassette tape player operation Turn the ignition to ACC or ON and care fully insert a cassette tape into the tape door The cassette tape automatically pulls into the player and begins to play When a casssetie is inserted into the audio system the word TAPE illuminates in the display to inform you that there is a tape in the radio If the radio is already operating it automati cally turns off the CD or radio station and the cassette tape begins to play and TAPE 1 PLAY is displayed TAPE 1 PLAY indicates side 1 is playing on the tape currenty The cassette tape automatically changes direc tion to play the other side when the first side is complete and will display TAPE 2 PLAY PLAY STOP Push the CD AM or FM button while the cassette tape is playing to stop the tape Push the TAPE button to play the tape Changing the direction of tape play Push the SIDE 1 2 select button to switch sides on the tape The display will change from TAPE 1 PLAY to TAPE 2 PLAY FF Fast Forward REW Rewind Push the REW or FF button for the desired direction When REW is pushed TAPE 1 REW illumi nates on the display TAPE 2 REW will illuminate if on side 2 When FF is pushed TAPE 2 FF illuminates on the display TAPE 2 FF will illuminate if on side 2 To stop the FF or REW function press the FF or REW button again or the TAPE button Dolby NR Noise Re
142. e seat Pull the cup holder out from the seat to use The cup holder can be adjusted to fit smaller cups by pushing in the arms The arms have three detents and then return to the fully open position 2 26 Instruments and controls E a PULL to open APDO601 GLOVE BOX Open the glove box by pulling the handle CAUTION Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop CARGO NET The cargo net keeps packages in the cargo area from moving around while the vehicle is in motion To install the cargo net attach the four loops to the four retainers To remove the cargo net detach the four loops from the cargo net retainers Rear cargo net APD1067 A WARNING e Properly secure all cargo to help prevent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or collision unsecured cargo could cause per sonal injury e Be sure to secure all four loops onto the retainers The cargo restrained by the net must not exceed 50 Ibs 22 7 kg or the net may not stay secured Instruments and controls 2 27 Parcel shelf lock knob Parcel shelf net retainer Parcel shelf net loop Parcel sheir h position 2 DANNA ves A Parcel shelf Ea a5 gt position 1
143. e set forth in the appropri ate NISSAN Service Manual Incor rect disposal procedures could cause personal injury The front seat pre tensioner seat belt sys tem activates in conjunction with the supple mental front air bag Working with the seat belt retractor it helps tighten the seat belt 1 36 Seats restraints and supplemental air bag systems the instant the vehicle becomes involved in certain types of collisions thereby restrain ing seat occupants The pre tensioner is encased with the seat belt s retractor These seat belts are used the same as conventional seat belts When the pre tensioner seat belt activates smoke is released and a loud noise may be heard The smoke is not harmful and does not indicate a fire Care should be taken to not intentionally inhale it as it may cause irritation and choking Those with a history of a breathing condition should get fresh air promptly If any abnormality occurs in the pre tensioner system the air bag warning light a will flash intermittently after the igni tion key is turned to the ON or START position In this case the pre tensioner seat belt will not function properly When selling your vehicle we request that you inform the buyer about the pre tensioner seat belt system and guide the buyer to the appropriate sections in this owner s manual WARNING SRS AIR BAG The warning labels are A located on the surface A of the sun visors SUP
144. e station manager If you use oxygenate blend gasoline please take the following precautions as the usage of such fuels may cause vehicle perfor mance problems and or fuel system dam age e The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline e If an oxygenate blend excepting a methanol blend is used it should contain no more than 10 oxygenate MTBE may however be added up to 15 e If a methanol blend is used it should contain no more than 5 methanol methyl alcohol wood alcohol It should also contain a suitable amount of appropriate cosolvents and corro sion inhibitors If not properly formu lated with appropriate cosolvents and corrosion inhibitors such methanol blends may cause fuel system dam age and or vehicle performance prob lems At this time sufficient data is not available to ensure that all metha nol blends are suitable for use in NISSAN vehicles If any undesirable driveability problems such as engine stalling and difficult hot starting are experienced after using oxygenate blend fuels immediately change to a non oxygenate fuel or a fuel with a low blend of MTBE Take care not to spill gasoline during refueling Gasoline containing oxygen ates can cause paint damage Aftermarket fuel additives NISSAN does not recommend the use of any fuel additives i e fuel injector cleaner octane booster intake valve deposit remov ers
145. e stop light 0 8 27 Brake pedal sisssvssssdssscrsseeasntasnedsrstnesiees 8 21 Brake SYSLCIM scscicssesccrsccscssesecersscteczetesss 5 14 Brake warning light wee 2 9 Brake wear indicators 2 12 Parking brake check cceeee 8 21 Parking brake operation 0 c ee 5 9 Self adjusting brakes 8 21 Break in schedule 05 fe Or Mt Bulb check instrument panel ee 2 8 Bulb replacement isisisi 8 27 Cc Capacities and recommended fuel TUDNICANS asinina 9 2 Car phone or CB radio eee eeeeeeeeeeeee 4 46 GArQO Metisse eeuna e Ee 2 27 Cargo See vehicle loading information 9 13 Check engine indicator light See malfunction indicator light Child restraint with top tether strap Child restraints sessin Child safety sliding door lOck eeeee Cigarette lighter accessory and ashtray 2 23 Cleaning exterior and interior Cold weather driving Compact disc CD player Controls Audio controls rear eee Audio controls steering wheel Heater and air conditioner controls AULOMALIC i sscetscies cessseeticesececcseceeereeiersets 4 11 Heater and air conditioner controls AMUN ede dues savace cos sacra casiccascudeectactsSueechd 4 3 Rear seat air conditioner 4 14 Coolant Capacities and recommended fuel lubricant Sesinin 9 2 Changing engine coolant ser O29 Checking engine coolant
146. eathing condition should get fresh air promptly The supplemental front air bags along with the use of seat belts help to cushion the impact force on the face and chest of the occupant They can help save lives and reduce serious injuries However an inflat ing front air bag may cause facial abrasions or other injuries Front air bags do not provide restraint to the lower body Seat belts should be correctly worn and the driver and passenger seated upright as far away as practical from the steering wheel or instrument panel The supplemental front air bag inflates quickly in order to help protect the front occupants Because of this the force of the front air bag inflating can in crease the risk of injury if the occupant is too close to or is against the air bag module during inflation The air bag deflates quickly after a collision The supplemental air bags operate only when the ignition switch is in the ON or START position After turning the ignition key to the ON position the supplemental air bag warn ing light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is opera tional A WARNING e Do not place any objects on the steering wheel pad or on the instru ment panel Also do not place any objects between any occupant and the steering wheel or instrument panel Such objects may become dangerous projectiles and cause in jury if the supplemental front air b
147. echnical and consumer information e Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 REPORTING SAFETY DEFECTS US only If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA in addition to no tifying NISSAN lf NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot be come involved in individual problems be tween you your dealer or NISSAN To contact NHTSA you may either call the Auto Safety Hotline toll free at 888 327 4236 If you reside in Hawaii please call 808 836 0888 You may also write to NHTSA U S Department of Transporta tion Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline You may notify NISSAN by contacting our Consumer Affairs Department toll free at 1 800 NISSAN 1 In Hawaii call 808 836 0888 READINESS FOR INSPECTION MAINTENANCE I M TEST US only Due to legal requirements in some states and Canadian Provinces your vehicle may be required to be in the ready condition for an Inspection Maintenance I M test of the emission control system The vehicle is set to the ready condition when it is driven through certain driving pat
148. ect the spark plug cables from the spark plugs When disconnecting always hold the boots not the cables 2 Remove the spark plugs with a spark plug socket The plug socket has a rub ber seal that holds the spark plug so it does not fall when it is pulled out Make sure each spark plug is snugly fitted into the plug socket 3 Fit the new plugs one at a time into the spark plug socket and install them Use only the specified spark plugs Turn each plug several full turns by hand then tighten with the spark plug socket to the correct torque Do not overtighten Spark plug tightening torque 14 to 22 ft lb 20 to 29 N m 4 Holding the boot re connect each high tension cable to its proper spark plug by pushing it on until you feel a snap AIR CLEANER ADIO579 The filter should not be cleaned and reused Replace it according to the maintenance intervals shown in the NISSAN Service and Maintenance Guide When replacing the filter unclip the four clamps and remove the filter Wipe the inside of the air cleaner housing and the cover with a damp cloth when replacing filter Maintenance and do it yourself 8 17 amp WARNING e Operating the engine with the air cleaner removed can cause you or others to be burned The air cleaner not only cleans the air it stops flame if the engine backfires If it isn t there and the engine backfires you could be burned Do not drive with the air clea
149. ective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly It is extremely dangerous to ride ina cargo area inside of a vehicle In a collision people riding in these ar eas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts Be sure everyone in your vehicle is in a seat and using a seat belt prop erly Do not place hard items such as coffee mugs or drinking glasses on the tabletop seats when the vehicle is moving Any item can become a projectile inside a vehicle involved in a collision To help prevent personal injury never leave loose items on the fold down tabletop seats when the vehicle is moving 1 20 Seats restraints and supplemental air bag systems Normal driving arrangement seven passenger third seat in seating position 1 More leg room APDO096 SEAT POSITIONS With second row bench seat The most common seating arrangement for seven passengers is with the three passenger bench seat in seating position 1 This provides more leg room for the passengers sitting in the third row Seven passenger driving arrangement with third seat in seating position 2 More cargo room When more cargo area room is necessary the three passenger sliding bench seat can be moved to seating position 2 or 8
150. ed rating of the tire If you operate your vehicle in snowy or icy conditions NISSAN recommends the use of snow or all season tires on all four wheels For additional traction on icy roads studded tires may be used However some U S states and Canadian provinces prohibit their use Check local state and provincial laws before installing studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires TIRE CHAINS Use of tire chains may be prohibited accord ing to location Check the local laws before installing tire chains When installing tire chains make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer s sug gestions Use only SAE Class S chains Other types may damage your vehicle Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit Loose end links of the tire chain must be secured or removed to prevent the possibil ity of whipping action damage to the fenders or undercarriage If possible avoid fully loading your vehicle when using tire chains In addition drive at a reduced speed Do not exceed maximum speed suggested by the chain manufacturer Otherwise your ve hicle may be damaged and or vehicle han dling and performance may be adversely affected Never install tire chains on TEMPORARY USE ONLY spare tires Do not use tire
151. ee passenger seat 1 7 Spark plug replacement cece 8 16 Speedometer sis assassins 2 5 Spotlights See map light cee 2 35 SRS warning label cee nessa 1 37 Starting Before starting the engine 5 5 Jump starting eee 6 8 8 15 Precautions when starting and driving 5 2 PUSM STAMMING lt ccccsersececsnesssccotsensaesnstcenoes Starting the engine Steering Power steering fluid 0 00 Tilting steering wheel SLOP liGhtalesccteekeviclerees decent Storage Overhead storage compartmert 2 24 Under seat storage tray 1 11 SUN Shadia 2 33 UUM OO eee seen ch cetsceadfee cadet cesecencencet aaa 2 33 Supplemental restraint system Information and warning labels 1 37 Switch Autolamp SWItCHh ou eee 2 18 Automatic power window switch 2 31 Hazard warning flasher switch 2 19 Headlight control switch 2 16 ignition SWITCH sessin eserine 5 4 Overdrive SWItCH 0 eee eeeeeereeteeeeeeees 5 8 Rear window defogger switch 2 16 Rear window wiper and washer SWILCI OS cates ere aesae ina Tea A EEEN 2 16 Turn signal SWitCh ees 2 19 Windshield wiper and washer switch 2 15 Tabletop SCats wciicescinccsccvecvecsvcsersecreierterss Tachometer Three passenger bench seat Three passenger bench seat in fully forward POSITION cccesccisccrssccsszstsscesseseceeroevis 1 29 Three passenger bench seat in storage POSION
152. eeeeeeeeeeeeees 5 5 Starting the engine 0 cece eeeeeseeesesseeteeeeeeetaee 5 5 Driving the Ve hiCle ccesseeeeeseeeseeeeeeeereereeners 5 6 Parking brake ccccscceesceeeeseeeeeeeneeseseneeeseeeneneeeee 5 9 Cruise Control eeeeeeeeeeeeeeeeeeeeeeeeteeeteeeeeeeeneeees 5 10 Precautions on cruise control 5 10 Cruise control operations seseeeeeeeeeeeeee 5 10 Break in schedule ccceecceeeeeeeeeeeeeeeeeeeeeecees 5 11 Increasing fuel economy sssssisrnssrnrserereene 5 12 Parking parking on hills 5 13 POWer Stering iu s seecite ent deecieectesteceeeessceedeeereenseces 5 14 Brake Syste raiceiras 5 14 Braking precautions srecni 5 14 Anti lock brake system ABS n se 5 14 Cold weather driving ecceeceeeeeeeeeeeeeteeeeeeeee 5 16 Freeing a frozen door lOCK ee eeeeeeeeeeeeeeee 5 16 ANUI FINGOZG a sacctcaseczeresceecuvazesinccezane aatia 5 16 SE E ES 5 16 Draining of coolant water eee 5 16 Tire equipment sssssesssereesenersnnrrnrerrnarrnrernnnne 5 16 Special winter equipment seseeeeeeeeeeeeeeeeeee 5 17 Driving ON SNOW OF ICC eeeeeeeteeeeteeeeeeeeeeeee 5 17 Engine block heater if so equipped 5 18 PRECAUTIONS WHEN STARTING AND DRIVING A WARNING Do not leave children impaired adults or pets alone in your vehicle They could accidently injure themselves or others through inadvertent operation of the vehicle Also on hot su
153. en the rear audio controls are on Press the three Heater air conditioner and audio systems 4 41 and five memory preset buttons to turn OFF the RSEM VOLUME button The VOLUME button allows the rear pas sengers to adjust the headphone volume level Push the button to increase the volume Push the button to decrease the volume MEDIA button The MEDIA button allows the rear passen gers to change between the different media options When a source of media is se lected that media selection is backlit e AM AM radio frequency band FM1 FM2 FM radio frequency bands TAPE cassette tape CD single CD player if so equipped CD DJ CD changer if so equipped VCP video cassette player AUX auxiliary jack input MEM button In AM FM1 or FM2 mode the MEM button allows the rear passengers to successively access memory preset stations 1 through 6 In CD DJ mode the MEM button allows the rear passengers to select other compact discs in the CD changer Play will begin with the first track SEEK button In AM FM1 or FM2 mode the SEEK lt and gt buttons allow the rear passengers to find the next radio station up or down the station band frequency In TAPE mode the SEEK lt and gt buttons allow the rear passengers to use Automatic Music Search AMS to find the next or previous song on the cassette In CD mode the SEEK lt and gt buttons allow the rear passengers to find the next or previ
154. er fuel economy Air conditioner operation lowers fuel economy Use the air conditioner only when necessary When cruising at highway speeds it is more economical to use the air condi tioner and leave the windows closed to reduce drag PARKING PARKING ON HILLS Downhill with curb t E cS cS a CaS es Sar Se A WARNING Do not stop or park the vehicle over flammable materials such as dry grass waste paper or rags They may ignite and cause a fire 1 Firmly apply the parking brake 2 Move the selector lever to the P Park position Uphill with curb e Uphill or downhill no curb ASDO007 A WARNING Safe parking procedures require that both the parking brake be set and the transmission placed into P Park position Failure to do so could cause the vehicle to move unexpect edly or roll away and result in an accident Make sure the shift lever has been pushed up as far as it can go and cannot be moved without pulling it towards you Never leave the engine running while the vehicle is unattended e Do not leave children unattended in side the vehicle They could unknow ingly activate switches or controls Unattended children could become involved in serious accidents To help prevent the vehicle from rolling into the street when parked on a sloping driveway it is a good practice to turn the wheels as illustrated HEADED DOWNHILL WITH CURB Turn the whee
155. er shoulder belts are located slightly behind the third row seating position Never try to use the seat belts for the second row passen gers which are in front of the three passenger bench seat A WARNING Use of the second row three point seat belts by third row passengers could increase the chance or severity of in jury in a sudden stop or an accident 2 Slowly pull the seat belt out of the retrac tor and insert the tongue into the buckle until you hear and feel the latch engage The retractor is designed to lock during a sudden stop or on impact A slow pulling motion permits the belt to move and allows you some freedom of move ment in the seat Three passenger bench seat TAKE UP slack POSITION ARS 1084 low on the hips 3 Position the lap belt portion low and snug on the hips as shown 4 Pull the shoulder belt portion toward the retractor to take up extra slack TWO POINT TYPE SEAT BELT WITHOUT RETRACTOR Center of rear seat Selecting correct set of seat belts The seat belt tongues must be fastened into the seat belt buckles as illustrated above amp WARNING Any rear seat belt tongue will connect to any seat belt buckle therefore it is important to follow the illustration above Failure to do so could increase Seats restraints and supplemental air bag systems 1 51 the chance and or severity of injury in an accident ARS1055 Fastening the sea
156. ery fluid to contact your skin eyes fabrics or painted surfaces After touching a battery or battery cap do not touch or rub your eyes Thoroughly wash your hands If the acid contacts your eyes skin or clothing immediately flush with water for at least 15 min utes and seek medical attention Do not operate the vehicle if the fluid in the battery is low Low battery fluid can cause a higher load on the battery which can generate heat re duce battery life and in some cases lead to an explosion When working on or near the battery always wear suitable eye protection and remove all jewelry Battery posts terminals and related accessories contain lead and lead compounds Wash hands after han dling Keep the battery out of the reach of children WDI0022 Check the fluid level in each cell It should be between the MAX and MIN lines If it is necessary to add fluid add only distilled water to bring the level to the indi cator in each filler opening Do not overfill 1 Remove the cell plugs using a suitable tool 2 Add distilled water up to the MAX level 3 Tighten cell plugs Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level JUMP STARTING If jump starting is necessary see the In case of emergency section If the engine does not start by jump starting the battery may have to be replaced Contact an autho rized
157. es Always drive your vehicle at a moderate speed Always block the wheels on both vehicle and trailer when parking Parking on a slope is not recommended however if you must do so first block the wheels and apply the parking brake and then move the transmission shift selector le ver into the P Park position If you move the shift selector lever to the P Park position before blocking the wheels and applying the parking brake transmission damage could occur e When going down a hill shift into a lower 9 18 Technical and consumer information gear and use the engine braking effect When ascending a long grade downshift the transmission to a lower gear and reduce speed to reduce chances of en gine overloading and or overheating If the engine coolant rises to an ex tremely high temperature when the air conditioning system is on turn the air conditioner off Coolant heat can be ad ditionally vented by opening the win dows switching the fan control dial to high and setting the temperature control dial to the WARM position Trailer towing requires more fuel than normal circumstances Avoid towing a trailer for the first 500 miles 800 km of the vehicle s life Have your vehicle serviced more often than at intervals specified in the recom mended Maintenance Schedule in the NISSAN Service and Maintenance Guide When making a turn your trailer wheels will be closer to the inside of the turn than yo
158. es Avoid resting your foot on the brake pedal while driving This overheats the brakes wears out the brake linings and pads faster and reduces fuel economy To help save the brakes and to prevent the brakes from overheating reduce speed and downshift to a lower gear before going down a slope or long grade Overheated brakes may reduce braking performance and could result in loss of vehicle control Wet brakes When the vehicle is washed or driven through water the brakes may get wet Asa result your braking distance is longer and the vehicle may pull to one side during braking To dry the brakes drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes Do this until the brakes return to normal Avoid driving the vehicle at high speeds until the brakes function correctly A WARNING e While driving on a slippery surface be careful when braking accelerat ing or downshifting Abrupt braking or acceleration could cause the wheels to skid and result in an acci dent e If the engine is not running or is turned off while driving the power assist for the brakes will not work Braking will be harder ANTI LOCK BRAKE SYSTEM ABS The anti lock brake system controls the brakes at each wheel so the wheels do not lock when braking abruptly or when braking on slippery surfaces The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each w
159. es is substantially reduced in snowy and icy conditions If you operate your vehicle on snowy or icy roads NIS SAN recommends using MUD amp SNOW or ALL SEASON tires on all four wheels Please consult your NISSAN dealer for the tire type size speed rating and avail ability information 2 For additional traction on icy roads stud ded tires may be used However some Canadian provinces and U S states pro hibit their use Check local state and pro vincial laws before installing studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires 3 Tire chains may be used Make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer s suggestions In ad dition drive at a reduced speed other wise your vehicle may be damaged and or vehicle handling and performance may be adversely affected Use of tire chains may be prohibited accord ing to location Check the local laws before installing tire chains When installing tire chains make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer s sug gestions Use only SAE Class S chains Other types may damage your vehicle Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit Loose end links of the tire chain must be secured or removed
160. es or controls Unattended children could become involved in serious accidents amp CAUTION e Always use the door handle to open or close a sliding door Do not at tempt to open or close the doors by merely placing your hand on the door edge or door slide roller as this may cause injury e Always be sure that hands and feet are clear of the door frame to avoid injury while closing a sliding door e When opening a sliding door on a slope ensure that it is fully open and that it does not close by itself Driver side j Jj ee NEUTRAL UNLOCK 1 A ONE DOOR UNLOCK 2 LOCK P ALL DOORS lt Front l APD1057 LOCKING WITH KEY Turning the door key one time to the rear of the vehicle unlocks the corresponding door From that position returning the key to Neutral where the key can only be removed and inserted and turning it to the rear again within 5 seconds unlocks all doors Turning the door key to the front of the vehicle locks all doors The selective unlock function and locking all doors can be operated from the driver passenger and rear door Driver side front door Door lock knob WPD0087 LOCKING WITH INSIDE LOCK KNOB To lock all doors from inside the vehicle push the door lock knob in then close the door When locking the doors this way be certain not to leave the key inside the ve hicle All doors automatically unlock if the key is in the ignition
161. eti Vehicle identification ccceceeceeeeeteeteeeeeeees Vehicle identification number VIN Vehicle identification number chassis number sicsissiessieissiiasicasiasss Engine serial nUmbe cceeseeeeeeeeereees F M V S S certification label cc cee Emission control information label Tire placards a 9 12 Air conditioner specification label 9 12 Installing front license plate 9 12 Vehicle loading information eeeeeeeeeeeeee 9 13 TONING arenans 9 13 Determining vehicle load capacity 4 9 13 Loading TIPS ussiisa 9 13 TOWING a traile Teissier saa eaaa 9 14 Maximum load limts ee 9 14 TOWING SATETY ccsceczsscscsessvetessadeteascetanavoeeevencteesed 9 15 Uniform tire quality grading e ce eeeeeeeeeeeeees 9 19 Emission control system warranty s e 9 20 Reporting safety defects US onlly eee 9 20 Readiness for inspection maintenance I M test US Only sc cece teers iaiia 9 21 Owner s manual service manual order Information 9 22 In the event of a collision ee eee eee 9 23 CAPACITIES AND RECOMMENDED FUEL LUBRICANTS The following are approximate capacities The actual refill capacities may be a little different When refilling follow the procedure instructed in the Do it yourself section to determine the proper refill capacity Capacity Approximate US Imp Recommended Fluids amp Lubricants
162. ey eventually turn off automatically to prevent the battery from becoming discharged If the interior lights are left in the ON position with all doors closed they will automatically turn off after approximately 30 minutes Lights that illuminate when the front or sliding doors are opened turn off after approxi mately 30 minutes Lights that illuminate when the back door is opened turn off after approximately 60 minutes Vanity mirror lights are not part of the battery saver system If the personal reading lights are left on after the key is removed from the ignition they will automatically turn off after approxi mately 30 minutes HomeLink UNIVERSAL TRANSCEIVER if so equipped The HomeLink Universal Transceiver pro vides a convenient way to consolidate the functions of up to three individual hand held transmitters into one built in device The HomeLink Universal Transceiver will operate garage doors gates home office lighting systems and security sys tems by storing and transmitting the pro gramming information of your current hand held transmitters The HomeLink Universal Transceiver is built in and powered by your vehicle s battery and charging system No separate batteries are necessary amp WARNING Do not use this HomeLink Universal Transceiver with any garage door opener that lacks safety stop and re verse features as required by federal safety standards these standards be came effect
163. f the radiator and clean off any dirt insects leaves etc that may have accumulated Make sure the hoses have no cracks de formation rot or loose connections Engine drive belts Make sure the drive belts are not frayed worn cracked or oily Battery Check the fluid level in each cell It should be between the MAX and MIN lines Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level Exhaust system Make sure there are no loose supports cracks or holes If the sound of the exhaust seems unusual or there is a smell of exhaust fumes immedi ately have the exhaust system inspected by an authorized NISSAN dealer See the car bon monoxide warning in the Starting and driving section of this manual Underbody The underbody is frequently exposed to corrosive substances such as those used on icy roads or to control dust It is very important to remove these sub stances from the underbody otherwise rust may form on the floor pan frame fuel lines and exhaust system At the end of winter the underbody should be thoroughly flushed with plain water in those areas where mud and dirt may have accumulated See the Appearance and care section of this manual Fluid leaks Check under the vehicle for fuel oil water or other fluid leaks after the vehicle has been parked for a while Water dripping from the air conditioner after use is normal If you should
164. f the reach of children 8 12 Maintenance and do it yourself TEMPERATURE CONDITIONS FOR CHECKING e Check the fluid level using the HOT range on the dipstick after the following conditions have been met The engine is warmed up to operating temperature The vehicle is driven at least 15 minutes The automatic transmission fluid is warmed to between 150 F and 170 F 66 C and 77 C e The fluid can be checked at fluid tem peratures of 70 F to 95 F 21 C to 35 C using the COLD range on the dipstick after the engine is warmed up and before driving However the fluid should be re checked using the HOT range 1 Park the vehicle on a level surface and set the parking brake 2 Start the engine then move the shift selector lever through the range of gears ending in P Park Front side Hot 150 to 170 F 66 to 77 C FL HOT I1 Ill Reverse side Cold 70 to 95 F 12 to 35 C COLD Reel OK Add WDI0004 Check the fluid level with the engine idling Remove the dipstick and wipe it clean with a lint free cloth Reinsert the dipstick into the dipstick tube as far as it goes Remove the dipstick and note the read ing If the level is at the low side of either range add fluid through the dipstick tube CAUTION DO NOT OVERFILL Use ONLY Nissan Matic D Continental U S and Alaska or Canada NISSAN Automatic Trans
165. f the fuse is open replace it with a new fuse 6 If a new fuse opens again have the electrical system checked and repaired by an authorized NISSAN dealer Fusible links If the electrical equipment does not operate and fuses are in good condition check the fusible links If any of these fusible links are melted replace only with genuine NISSAN parts If the new fusible link melts again have the system checked and repaired by an autho rized NISSAN dealer y PULL to open S5 Fuse box cover PASSENGER COMPARTMENT amp CAUTION Never use a fuse of a higher amperage rating than that specified on the fuse box cover This could damage the elec trical system or cause a fire If the electrical equipment does not operate check for an open fuse 1 Remove the key from the ignition Fuse puller 2 WDI0023 Open the fuse box cover Refer to the fuse label on the fuse box cover to locate the fuse in question Remove the fuse with the fuse puller 4 If the fuse is open replace it with a new fuse If a new fuse opens again have the electrical system checked and repaired by an authorized NISSAN dealer Maintenance and do it yourself 8 23 KEYFOB BATTERY REPLACEMENT side APD1087 Replace the battery as follows 3 Close the lid securely 1 Open the lid using a coin 4 Press the g button the
166. grated child safety seats Seat IN SECON rOW corsicis 1 72 If SOVSQUIPDOG iniinis 1 73 SEATS Sit upright and well back A WARNING Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries ARS1131 e For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat properly See Precautions on Seat Belt Usage later in this section 1 2 Seats restraints and supplemental air bag systems FRONT MANUAL SEAT ADJUSTMENT amp WARNING e Do not adjust the driver s seat while driving so full attention may be given to vehicle operation The seat may move suddenly and could cause loss of control of the vehicle e After adjustment gently rock in the seat to make sure it is securely locked Forward and backward Recline ROTATE upward PULL upward ARS1211 Forward and backward Reclining Rotate the lever up while you slide the seat To recline the seatback pull the lever up and forward or backward to the desired position lean back To bring the seatback forward Release the lever to lock the seat in position again pull the lever up and move your body
167. h an old to the charging system and cause per cloth to reduce explosion hazard sonal Injury 4 Connect jumper cables in the sequence 1 If the booster battery is in another ve as illustrated hicle position the two vehicles to bring their batteries close to each other A CAUTION Do not allow the two vehicles to touch Always connect positive to posi tive and negative to body 2 Apply the parking brake Move the gear ground for example the strut shift lever to the P Park position Switch mounting bolt engine lift bracket off all unnecessary electrical systems etc not to the battery lights heater air conditioner etc In case of emergency 6 9 e Make sure the jumper cables do not touch moving parts in the engine compartment and that the clamps do not contact any other metal 5 Start the engine of the other vehicle and let it run for a few minutes 6 Keep the engine speed of the other ve hicle at about 2 000 RPM and start the engine of the vehicle being jump started A CAUTION Do not keep the starter motor engaged for more than 10 seconds If the engine does not start right away turn the key off and wait 3 to 4 seconds before trying again 7 After starting your engine carefully dis connect the negative cable and then the positive cable 8 Replace the vent caps if so equipped Be sure to dispose of the cloth used to cover the vent holes as it may be con taminated with corros
168. h materials and services ranging from the operation of port facilities and transportation services to the supply of lubri cants parts and accessories NISSAN pioneered the use of electronics and computers in automobiles and has led the indus try in improving both performance and fuel effi ciency through new engine designs and the use of synthetic materials to reduce vehicle weight The company has also developed ways to build quality into its vehicles at each stage of the production process both through extensive use of automation and most importantly through an awareness that people are the cen tral element in quality control From the time the parts arrived from our suppli ers until you took delivery of your new NISSAN dozens of checks were made to ensure that only the best job was being done in producing and delivering your vehicle NISSAN also takes great care to ensure that when you take your NISSAN to your dealer for maintenance the service techni cian will perform his work according to the quality standards that have been established by the factory Safety has also been built into your NISSAN As you know seat belts are an integral part of the safety systems that will help protect you and your passengers in the event of a sudden stop or an accident We urge you to use the seat belts every time you drive the vehicle The NISSAN story of growth and achievement reflects our major goal to provide you our custo
169. haust gases to escape e Never get under the vehicle while it is supported only by a jack If it is necessary to work under the vehicle support it with safety stands e Keep smoking materials flame and sparks away from the fuel tank and battery e On gasoline engine models with the multiport fuel injection MFI system the fuel filter or fuel lines should be serviced by an authorized NISSAN dealer because the fuel lines are under high pressure even when the engine is off 8 6 Maintenance and do it yourself CAUTION e Do not work under the hood while the engine is hot Turn off the engine and wait until it cools down e Never connect or disconnect the bat tery or any itransistorized compo nent while the ignition switch is in the ON position e Avoid contact with used engine oil and coolant Improperly disposed engine oil engine coolant and or other vehicle fluids can damage the environment Always conform to lo cal regulations for disposal of ve hicle fluid This Maintenance and do it yourself sec tion gives instructions regarding only those items which are relatively easy for an owner to perform A genuine NISSAN service manual is also available See Owners manual Service manual order information in the Technical and consumer information section You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions and could affect y
170. he auto set feature When AUTO is depressed for less than 5 seconds the display window momentarily indicates AUTO ON and the radio seeks the first six strong stations for the respective band The first six strong stations are then stored in order in memory buttons one through six Heater air conditioner and audio systems 4 21 Only stations in the selected band are set and the station seek begins from the last frequency stored in memory button six If AM FM SCAN TUNE SEEK AUTO or a memory button is pushed while auto set is operating auto set is canceled and AUTO OFF shows in the display window AUTO LOAD Press the AUTO button for longer than 5 seconds while listening to the radio to acti vate the auto load feature When AUTO is depressed for longer than 5 seconds the display window momentarily indicates AUTO LOAD and the radio seeks the first six strong stations for every band The first six strong stations are then stored in order in memory buttons one through six for each band AM FM1 and FM2 SEEK tuning Push the SEEK or gt buttons to find the next broadcast station Pushing the lt q SEEKS up and button SEEKS down Pushing the button again continues the SEEK function Once the highest broadcast station is reached the radio continues in the SEEK mode at the lowest station Once the lowest broadcast station is reached the radio con tinues in the SEEK mode at the highest station SCAN tuning Pu
171. he automatic locking mode 7 Check to make sure the child restraint is properly secured prior to each use If the belt is not locked repeat steps three through six After the child restraint is removed and the seat belt is fully retracted for the passenger side of the two passenger bench seat the auxilliary buckle must also be released the automatic locking mode child restraint mode is canceled Rear facing The following instructions apply to second row bucket seats the second row bench seat and the outboard positions of the three passenger bench seat A WARNING When installing a child restraint in the two passenger bench seat if it is placed in the seating position next to the passenger side sliding door be sure both the auxiliary buckle and main buckle are properly fastened Failure to do so could increase the chance and or severity of injury in an accident A WARNING e The three point belt in your vehicle is equipped with a locking mode re tractor which must be used when installing a child restraint e Failure to use the retractor s locking mode will result in the child restraint not being properly secured The seat could tip over or otherwise be unse cured and cause injury to the child in a sudden stop or collision Seats restraints and supplemental air bag systems 1 61 Rear facing O Front ARS1181 When you install a child restraint in a rear outboard seat follow these ste
172. heel from locking and sliding By preventing wheel lockup the system helps the driver maintain steering control and helps to minimize swerv ing and spinning on slippery surfaces Using the system Depress the brake pedal and hold it down amp WARNING Do not pump the brake pedal Doing so may result in increased stopping dis tances Normal operation The anti lock brake system does not operate at speeds below 3 to 6 MPH 5 to 10 km h The speeds vary according to road condi tions When the anti lock brake system senses one or more wheels are close to locking up the actuator under the hood rapidly applies and releases hydraulic pres sure like pumping the brakes very quickly While the actuator is working you may feel a pulsation in the brake pedal and hear a noise or vibration from the actuator under the hood This is normal and indicates the anti lock brake system is working properly However the pulsation may indicate road conditions are hazardous and extra care is required while driving Self test feature The anti lock brake system consists of elec tronic sensors electric pumps and hydraulic solenoids controlled by a computer The computer has a built in diagnostic feature that tests the system each time you start the engine and move the ve hicle at a low speed in forward or reverse When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is norma
173. here appropriate fuel is not available When transferring the registration of your vehicle to another country state province or district it may be necessary to modify the vehicle to meet local laws and regulations The laws and regulations for motor vehicle emission control and safety standards vary according to the country state province or district Therefore vehicle specifications may differ When any vehicle is to be taken into another country state province or dis trict and registered its modifications transportation and registration are the responsibility of the user NISSAN is not responsible for any inconvenience that may result VEHICLE IDENTIFICATION ATI0563 VEHICLE IDENTIFICATION NUMBER VIN PLATE The vehicle identification number plate is attached to the upper portion of the dash board on the driver s side This number is the identification for your vehicle and is used in the vehicle registration 9 10 Technical and consumer information ATI1021 VEHICLE IDENTIFICATION NUMBER Chassis number Engine serial number ENGINE SERIAL NUMBER The number is stamped on the engine as AT1I1022 F M V S S CERTIFICATION LABEL The F M V S S certification label is affixed as shown This label contains valuable ve hicle information such as Gross Vehicle Weight Rating GVWR Gross Axle Weight Rating GAWR month a
174. hicle is mov ing The child could be seriously in jured or killed in an accident or sudden stop PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts The seat belt should be worn snug and always position the lap belt as low as possible around the hips not the waist Place the shoulder belt over your shoulder and across your chest Never run the lap shoulder belt over your abdominal area Contact your doctor for specific rec ommendations INJURED PERSONS NISSAN recommends injured persons use seat belts depending on the injury Check with your doctor for specific recommenda tions Front NN INSERT to fasten ARS1159 Front e POSITION low on the hips slack THREE POINT TYPE SEAT BELT WITH RETRACTOR amp WARNING e Every person who drives or rides in this vehicle should use a seat belt at all times e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an accident 1 42 Seats restraints and supplemental air bag systems you could be thrown into it and re ceive neck or other serious injuries You could also slide under the lap belt and receive serious internal injuries e For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat properly See Precautions on seat belt usage earlie
175. hield Operating tips e Clear snow and ice from the wiper blades and air inlet in front of the windshield This improves heater op eration e To defog the side windows more effec tively when in bi level or ventilation mode close the center vent and direct the side vents toward the side windows e A slight delay may be experienced when changing air control buttons The system is not malfunctioning It is only the sys tem motors and solenoids switching from one outlet to another AIR CONDITIONER OPERATION Start the engine move the fan control dial to the desired one to four position and select an air control position before pushing in the air conditioner button to activate the air conditioner When the air conditioner is on cooling and dehumidifying functions are added to the heater operation A WARNING The air conditioner cooling function op erates only when the engine is running Heater air conditioner and audio systems 4 5 NOTE When switching air flow outlets the A C system remains activated unless the A C button is pressed to the OFF position The indicator light on the A C button re mains illuminated unless the button is pressed to the OFF position or the OFF air control position is selected Cooling This mode is used to cool and dehumidify 1 Move the air control dial to the po sition 2 Turn the fan control dial to select speed 3 Push the air conditioner button The indi cator l
176. hile driving so full attention may be given to vehicle operation Some jurisdictions prohibit the use of cellular telephones while driving e If you must make a call while your vehicle is in motion the hands free cellular phone operational mode if so equipped is highly recom mended Exercise extreme caution at all times so full attention may be given to vehicle operation 4 46 Heater air conditioner and audio systems CM harness connector AHA1049 If a conversation in a moving vehicle requires you to take notes pull off the road to a safe location and stop your vehicle before doing so amp CAUTION Keep the antenna as far away as possible from the Electronic Control Module ECM Keep the antenna wire more than 8 in 20 cm away from the Multiport Fuel Injection harness Do not route the antenna wire next to any har ness Adjust the antenna standing wave ratio as recommended by the manu facturer Connect the ground wire from the CB radio chassis to the body For details consult an authorized NISSAN dealer 5 Starting and driving Precautions when starting and driving 5 2 Exhaust gas carbon monoxide eeeee 5 2 Three way catalyst eee eeeseeeeeseeeeeeeeereneees 5 2 Avoiding collision and rollover 5 3 Drinking alcohol drugs and driving 00 5 3 IQMILON SWIG seisi 5 4 KEY POSITIONS ecese ee eandecren ect ecetansert 5 4 Before starting the ENgine ee eee
177. his can be dangerous The shoulder belt will not be against your body In an acci iO dent you could be thrown into it and ecin receive neck or other serious inju nan A ries You could also slide under the APD0852 lap belt and receive serious internal injuries Seats restraints and supplemental air bag systems 1 7 Seat cushion release lever APD0853 Sliding Before sliding the seat fasten the center belt tongue to the center buckle and remove the appropriate floor mats 1 8 Seats restraints and supplemental air bag systems 1 Lift the seat cushion release lever 2 Lift the seat cushion up into the locked position 3 Lift the slide release lever and grasp the bar under the seat in the center 4 Slide the seat until locked at a passenger seating position or a storage position After the seat starts moving release the slide lever The seat latches at the next latching position Continue to lift and release the slide lever until the desired position is obtained To lower the cushion the seat must be locked at a passenger seating position Lift the seat cushion release lever and lower the cushion until locked The seat cushion cannot be lowered ina storage position This prevents a pas senger from using a seat or seat belt that is out of a seating position The seating system allows great flexibility 6 SEAT POSITIONS 3 Third Row Seating Positions 2 Storage
178. horn beep feature If desired the horn beep feature can be deactivated using the keyfob The instruc tions are on the back of the keyfob To deactivate Press and hold the and a buttons for at least two seconds The hazard lights will flash three times to confirm that the horn beep feature has been deactivated To activate Press and hold the and buttons for at least two seconds once more The hazard lights will flash three times to confirm that the horn beep feature has been reactivated Deactivating the horn feature does not si lence the horn if the alarm is triggered If the system does not operate as de scribed above have it checked by an authorized NISSAN dealer WINDSHIELD WIPER AND WASHER SWITCH ROTATE to desired speed AICO561 AICO559 To operate the wipers intermittently adjust the knob between the S slow and F fast positions For continuous operation select LO or HI To operate the washer press on the end of the wiper knob For more washer fluid push and hold the end of the wiper knob The wipers cycle a few times when the washer is activated The washer operates in any of the wiper positions amp CAUTION e Do not operate the washer continu ously for more than 30 seconds e Do not operate the washer if the reservoir tank is empty A WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may le
179. ic if So equipped sinisen 4 11 Heater and air conditioner manual 4 3 Rear seat air conditioner 05 4 14 Homelink Transceiver HomeLink Universal Transceiver If SO equipped 0 00 seceeeeeeeeesteentees 2 35 Hood 1elease siiis iin 3 9 POM ER A E E E 2 20 l ignition SWICH issnin 5 4 Important vehicle information label 9 11 Increasing fuel ECONOMY cece 5 12 Indicator lights and chimes See warning indicator lights and audible reminders 2 8 Inertia fuel shut off Switch 6 11 Instrument brightness control 06 2 17 Integrated child safety seats 1 73 WMS MOP GIS canei 2 34 J Jump starting 6 8 8 15 K KOY E E TE 3 2 Keyless entry system See remote keyless SMY SYSTEM okasas iaar aae 3 6 L Labels Air conditioner specification label 9 12 Emission control information label 9 11 Engine serial number 0 ee 9 11 F M V S S certification label 9 11 Vehicle identification number VIN 9 10 Vehicle identification number VIN platasini aniei 9 10 Warning labels for SRS 0 0 eee 1 37 License plate Installing the license plate 9 12 Light Air bag warning light ee 1 37 Brake light See stop light 0 8 27 Bulb check instrument panel 2 8 Bulb replacement cscsescssesereesees 8 27 Cornering gts 2 19 Headlight control switch 2 16 Headlights sirisser
180. ice complies with FCC rules part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may be received including interference that may cause undesired operation The transmitter has been tested and complies with FCC and DOC MDC rules Changes or modifications not expressly approved by the party responsible for compliance could void the user s author ity to operate the device DOC ISTC 1763K1313 FCC I D CB2V67690 Instruments and controls 2 39 MEMO 2 40 Instruments and controls 3 Pre driving checks and adjustments Key S anant e e esiedis ei a ities 3 2 DOOS atina aa ae e a E 3 2 Locking WIth Key ssecsissieosrses insna 3 3 Locking with inside lock KNOD eeeeeeeeen 3 3 Locking with power door lock switch 3 4 Child safety sliding door lOCKS ceeeee 3 5 Remote keyless entry system ceee 3 6 How to use remote keyless entry SV SUG Mises E T 3 6 Battery replacement 0 ce eeeeeeeeeeeeeneeeeenneereees 3 8 TOOG PE E T E T 3 9 F elfiller derrin a 3 10 Opener operation esseeeeeeeeeeieeeeeeeeeee ennenen 3 10 Fuel filler Capo ciseccecsesccnetieeeteseeteneceneeecteascncnests 3 10 Steering wheel 0 00 eeceeeeeeeeeeeeeeeeeeeeetseeteneeeeeees 3 11 Tilt OPOrAtlOM ccaceccnseccevesencessgcereccecanpeccenescecendey 3 11 SUNVISOlSsiteteids sin adi E 3 12 Vanity IMIR ropen emaa inindeen
181. ide 0 5 2 F Family entertainment system 0 0 4 37 Five passenger seating Five passenger seating with cargo room 1 29 Flashers See hazard warning flasher switch Flat tire Flexible SCatinGsisssissetsectsiscuarsaraccteteessanes 1 12 Floor mat positioning 1 27 1 30 Floor mat positioning aid 1 30 Fluid Automatic transmission fluid ATF 8 12 Brake fluid wictnwciwaee ener 8 13 9 2 Capacities and recommended fuel IUDIICANTS aissim e eect ee eeeeeeteeeeeeteeeeeee Engine CoolANt isinisi EMGIMe Oil aerae raana Power steering fluid z Window washer fluid 0 ceeeee F M V S S certification label 9 11 Fuel Capacities and recommended fuel IWbriCants ve chow ecards Fuel CCOMOMY civesttiseiscesdsncistenecesceesvansl Fuel filler lid and Cap Fuel filler lid lock opener lever Fuel QaAUJE isiin Fuel octane rating sic siicsicisescavecveinecs Fuel recommendation Inertia fuel shut off switch G Gauge Engine coolant temperature gauge 2 6 FUG GQ aAUGC a issis an 2 6 OdOMECIET issons 2 5 Speedometer ccececceeseeeeseeeeeeeseeesees 2 5 TWACGhOM tel eoii t 2 5 General maintenance 8 2 8 3 GIOVE DOK dind narn n 2 26 Hazard warning flasher switch Head restraints 0 cceceeeeeeee Headlight control SWitch ceeeee Headlights irinna Heated Seats niiina Heater Heater and air conditioner automat
182. ied The rear drum type brakes also self adjust every time the brake pedal is applied If the brake pedal goes down farther than normal see an authorized NISSAN dealer A WARNING See an authorized NISSAN dealer for a brake system check if the brake pedal height does not return to normal Brake pad wear indicators The disc pads on your vehicle have audible wear indicators When a brake pad requires replacement it makes a high pitched scrap ing or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the wear indicator sound is heard Under some driving or climate conditions occasional brake squeak squeal or other noise may be heard Occasional brake noise during light to moderate stops is nor mal and does not affect the function or performance of the brake system The rear drum brakes do not have audible wear indicators If you ever hear an unusu ally loud noise from the rear drum brakes have them inspected as soon as possible by Maintenance and do it yourself 8 21 an authorized NISSAN dealer Proper brake inspection intervals should be followed For more information regard ing brake inspections see the appropriate maintenance schedule information in the NISSAN Service and Maintenance Guide BRAKE BOOSTER Check the brake booster function as fol lows 1 With the engine off press and release the brake pedal sever
183. ight Maintenance and do it yourself 8 25 Push pins 8 26 Maintenance and do it yourself Removal Push Push center pin to catching position Do not remove center pin by hitting it Push Installation LDIO064 Disconnect electrical connector LDI0065 FOG LIGHTS Replacing the fog light bulb 1 Remove the three splash shield screws and three push pins 2 Move the splash shield out of the way 3 Disconnect electrical connector 4 Rotate the bulb counterclockwise until it is free from the fog light housing EXTERIOR AND INTERIOR LIGHTS Item Wattage W Bulb No Headlight assembly High Low Front turn signal light Front fog light Front combination light Front side marker light Parking Cornering Rear combination light Turn signal Stop Tail Rear side marker light Back up light License plate light High mounted stop light Interior lights Personal reading light Luggage compartment light Steplight Spotlight 65 55 8 25 27 27 3 8 8 25 27 27 8 25 27 5 27 3 8 12 10 12 12 10 9007 HB5 3157A 881L 194 3157 3156A 3157 168 3156 194 912 211 2 578 211 2 211 2 578 Maintenance and do it yourself 8 27 Steplight USES Door courtesy light LN Lee R wea AT Fog light if so equipped Front turn signal Front combination light Personal reading light Re
184. ight comes on 4 Move the temperature control dial to the desired position e For quick cooling when the outside tem perature is high move the air control dial to the MAX A C position Be sure to return the air control dial to the po sition for normal cooling Opening the windows helps to vent heat buildup when parked in the sun Dehumidified heating This mode is used to heat and dehumidify 1 Move the air control dial to the wv po sition 2 Turn the fan control dial to select speed 3 Push the air conditioner button The indi cator light comes on 4 Move the temperature control dial to the desired position Dehumidified defogging This mode is used to defog the windows and dehumidify 1 Move the air control dial to the 7 po sition 2 Turn the fan control dial to the desired speed 3 Move the temperature control dial to the desired position When the 7 position is selected the air conditioner automatically turns on however the indicator light will not illu minate if the outside temperature is more than 45 F 7 C This dehumidifies the air which helps defog the windshield 4 6 Heater air conditioner and audio systems The air recirculation mode automatically turns off allowing outside air to be drawn into the passenger compartment which helps defog the windshield Operating tips Keep windows and sun roof closed while the air conditioner is in operation After parking in
185. il you feel it latch SUNROOF if so equipped CS TILT down Mam TILT up AIC1066 C Co The sunroof operates when the ignition key is in the ON position or for 15 minutes after the ignition key is turned to the OFF posi tion If the driver s or passenger s door is opened during this 15 minute period power to the sunroof is cancelled NOTE If the battery is discharged or is discon nected the sunroof may not operate cor rectly and must be reset To reset a fully or partially open sunroof 1 Push and hold the UP CLOSE side of the sunroof switch until the sunroof closes and tilts up to the fully open position then release the switch 2 Push and hold the DOWN OPEN side of the switch until the sunroof lowers com pletely The sunroof is now reset and should operate correctly To reset a fully or partially tilted or closed sunroof 1 Push and hold the UP CLOSE side of the sunroof switch until the sunroof stops tilting up then release the switch 2 Push and hold the DOWN OPEN side of the switch until the sunroof lowers com pletely The sunroof is now reset and should operate correctly Sliding the sunroof To open the roof push and hold the OPEN side of the switch To close the roof push and hold the CLOSE side Tilting the sunroof To tilt up first close the sunroof then push the UP side of the switch To close the sunroof push the DOWN side of the swi
186. ill in the following illustrati Th ean you will see in the following illustrations The second row seats may be removed and the third row seat may be moved forward to the second row seating position The second and third row seats have a fold down table top feature This offers a variety of uses for the vehicle when moving or stopped position The illustrations shown reflect the different seating positions available LRSOO50 Before you begin to arrange the seats in your vehicle read all of the cautions and warnings in this section including the information on the removable floor mats Also observe any labels that are in the vehicle Seats restraints and supplemental air bag systems 1 19 A WARNING e While the vehicle is in motion pas sengers should always be seated in a forward facing direction in a seat which is properly secured and ad justed Seat belts should always be used Sitting without a seat belt ina seat that is not properly secured in one of the locations shown in this chapter or in a place without a seat and seat belt can result in personal injury in a sudden stop or collision Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries For the most eff
187. ind button button e PLAY button Press to play a videocas Play Stop button sette tape Button Fast e REW button Press to rewind the vid Forward button eocassette tape LHA0091 e FF button Press to fast forward the videocassette tape Remote control e STOP button Press to stop the video The remote control has the following con cassette tape trols Battery Replacement e POWER button Press to turn the VCP ON or OFF Batteries are supplied with the remote con trol unit e ENCORE button Press to reverse the videocassette tape for 5 seconds Nor mal playback will then resume Slide the battery cover off to access the batteries and only use alkaline batteries as replacements If you will not be using the e STILL ADVANCE button Press to tem remote control for long periods of time porarily suspend playback Press again remove the batteries to make the videocassette tape advance Replacement of the batteries is needed one frame at a time when the remote control only functions at Heater air conditioner and audio systems 4 39 LHA0092 Flip down screen A CAUTION e The glass screen on the liquid crys tal display may break if hit with a hard or sharp object If the glass breaks do not touch the liquid crys talline material which contains a small amount of mercury In case of contact with skin wash immediately with soap and water e The screen rotates down to view and up into th
188. indow The EATC heats or cools to achieve the set temperature When in AUTOMATIC and weather conditions require heat air is sent to the floor However a feature is included in the EATC to prevent blowing cold air to the floor if the engine coolant is not warm enough to allow heating In three or four minutes the fan speed gradu ally increases and airflow changes to the floor If unique conditions exist such as window fogging the five override buttons allow spe cific airflow selection The thumbwheel al lows you to adjust the fan speed to suit your needs Temperature selection The y TEMP A button on the left side of the control panel is for temperature selec tion The Ww side lowers the set tempera ture and the A side raises the set tem perature Press and hold either side of the button to rapidly change the temperature setting in one degree increments to either 65 F 18 C or 85 F 29 C If you want continuous maximum cooling push the wv side of the TEMP button until 60 F 16 C shows in the display window The EATC cools at maximum and disregards the 60 F 16 C setting until a warmer tempera ture is selected If you want continuous maximum heating push the A side of the TEMP button until 90 F 32 C shows in the display window The EATC provides maxi mum heat regardless of the 90 F 32 C setting until a cooler temperature is se lected Fan speed and thumbwheel Your EATC automatically adjusts th
189. int from side to side and tug it forward to make sure it is securely held in place 6 Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor If you cannot pull any more belt webbing out of the retractor the seat belt is in the automatic locking mode 7 Check to make sure the child restraint is properly secured prior to each use If the lap belt is not locked repeat steps three through six 1 66 Seats restraints and supplemental air bag systems After the child restraint is removed and the seat belt is fully retracted the automatic locking mode child restraint mode is can celed LATCH LOWER ANCHORS AND TETHER FOR CHILDREN SYSTEM Second row bench seat LRS0089 LATCH Anchor points amp WARNING e Attach LATCH system compatible child restraints only at the locations shown If a child restraint is not se cured properly your child could be seriously injured or killed in an acci dent e Do not secure a child restraint in the center rear seating position using the LATCH system anchors The child restraint will not be secured properly e The LATCH system anchors are de signed to withstand only those loads imposed by correctly fitted child re straints Under no circumstance are they to be used for adult seat belts or harnesses Some child restraints include two rigid or webbing mounted attachments that can be connecte
190. ion is activated SHUFFLE illuminates in the display LHA0049 CD CARE AND CLEANING e Handle a CD by its edges Never touch the surface of the disc Do not bend the disc e Always place the discs in the storage case when they are not being used e To clean a disc wipe the surface from the center to the outer edge using a clean soft cloth Do not wipe the disc using a circular motion Do not use a conventional record cleaner or alcohol intended for industrial use e A new disc may be rough on the inner and outer edges Remove the rough edges by Heater air conditioner and audio systems 4 33 rubbing the inner and outer edges with the side of a pen or pencil as illustrated A VOLUME Pa NEXT proceed to the next preset station AM FM YN mH a essan the next selection FEEN an l Ig on the tape or the a E next selection on the CD VOLUME v AHA1063 STEERING WHEEL SWITCH FOR AUDIO CONTROLS if so equipped The radio controls mounted on the right side of the steering wheel provide convenient access to three commonly used functions A VOL W VOL and NEXT Use the NEXT button to select the next pre programmed station AM FM the next se lection on the tape or the next selection on the CD 4 34 Heater air conditioner and audio systems VOLUME control MEDIA select Radio station SEEK button button button memory button
191. ir bag 1 34 _ a Passenger d i A f rare supplemental See Engine oil and oil filter recommenda Seats 1 2 ea 1 31 tion in the Technical and consumer infor mation section Seat belts 1 31 a ty Cold tire pressure Key 3 2 See tire placard affixed to the glove com partment lid Recommended new vehicle m break in procedure Fuel door 3 10 Spare tire During the first 1 000 miles 1 600 km of 6 3 vehicle use follow the recommendations outlined in the Break in schedule informa tion found in the Starting and Driving sec tion of this Owner s Manual Follow these recommendations for the future reliability and economy of your new vehicle Rear door lock 3 10 a WGS0010
192. is the set speed decreases by about 1 MPH 1 6 km h To resume the preset speed push and release the RES ACCEL switch The ve hicle resumes the last set cruising speed when the vehicle speed is over 29 MPH 47 km h BREAK IN SCHEDULE During the first 1 000 miles 1 600 km follow these recommendations for the future reliability and fuel economy of your new vehicle e Avoid driving for long periods at constant speed either fast or slow e Do not accelerate at full throttle in any gear e Avoid quick starts e Avoid hard braking as much as possible Do not tow a trailer for the first 500 miles 800 km Starting and driving 5 11 INCREASING FUEL ECONOMY 5 Abrupt starts and stops waste fuel and money SD1001M Accelerate slowly and smoothly Main tain cruising speeds with a constant ac celerator position Drive at moderate speeds on the high way Driving at high speed lowers fuel economy Avoid unnecessary stopping and brak ing Maintain a safe distance behind other vehicles Use a proper gear range which suits road conditions Avoid unnecessary engine idling 12 Starting and driving Keep your engine tuned up Follow the recommended periodic main tenance schedule Keep the tires inflated at the correct pressure Low tire pressure increases tire wear and wastes fuel Keep the wheels in correct alignment Improper alignment causes not only tire wear but also low
193. it for 3 consecutive minutes then release the accelerator pedal completely 10 Wait 5 seconds at idle 11 Rev the engine up between 2 000 and Technical and consumer information 9 21 3 000 rpm and maintain it for 5 consecu tive minutes 12 Stop the vehicle and turn the engine off 13 Repeat steps one through twelve at least one more time If steps one through seven are interrupted repeat the preceding step Any safe driving mode is acceptable between steps Do not stop the engine until step seven is com pleted 9 22 Technical and consumer information OWNER S MANUAL SERVICE MANUAL ORDER INFORMATION Genuine Nissan Service Manuals A genuine NISSAN Service Manual is the best source of service and repair informa tion for your vehicle Filled with wiring dia GET TH E grams illustrations and step by step diag nostic and adjustment procedures this S manual is the same one used by the factory IN AS DE trained technicians working at authorized NISSAN dealerships Also available are genuine NISSAN Owners Manuals and STO RY genuine NISSAN Service and Owner s Manuals for older NISSAN models In the USA For current pricing and availability of genu ine NISSAN Service Manuals for the 2000 model year and later contact Tweddle Litho Company 1 800 639 8841 www nissan techinfo com For current pricing and availability of genu ine NISSAN Service Manuals for the 1999 model year and prior see an authorized NI
194. it is securely locked Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly See Precautions on seat belt usage later in this section e When adjusting or moving any of the seats in your vehicle do not use any of the seat belt buckles tongues or webbing to carry or move the seats Lifting the seats by any of the seat belts could damage them Damaged seat belts should be replaced at your NISSAN dealer Failure to follow these instructions could increase the chance and or severity of injury in an accident A CAUTION The seats are heavy Two people should remove or install them Do not sit in seats that have been removed from the vehicle They may tip over and you could be injured 1 14 Seats restraints and supplemental air bag systems Removing the second row passenger side bucket seat Left side of seat PUSH down the recliner lever 1 Lift the recliner lever 2 Fold the seatback fully forward floor latch levers SLIDE seat N backward to release it from floor
195. ition while the ignition switch is ON The selector lever cannot be moved out of P Park and into any of the other gear positions if the ignition key is turned to LOCK or if the key is removed from the switch The shift lever can be moved if the igni tion switch is in the ACC position This allows the vehicle to be moved if the battery is discharged 1 Keep the brake pedal depressed and shift into a driving gear 2 Release the parking brake and brake pedal then gradually start the vehicle in motion gt First PULL toward you and then move lever C gt Move lever without pulling toward you Shifting P Park Use this selector position when the vehicle is parked or when starting the engine Al ways be sure the vehicle is at a complete stop For maximum safety depress the brake pedal pull the lever toward you and move the lever to the P Park position Apply the parking brake When parking on a hill apply the parking brake first then shift the lever into the P Park position Shifting from P Park If the ignition switch is in the ON position and the foot brake pedal is depressed but the shift lever still cannot be moved out of P Park follow these instructions 1 Shut the engine off and remove the key 2 Apply the parking brake 3 Reinsert the ignition key and turn it clock wise to the first position ACC 4 Depress the brake pedal move the gear shift lever to N Neu
196. itioner Air conditioner operation 0 e 4 5 Air conditioner service 0 4 15 Air conditioner specification label 9 12 Air conditioner system refrigerant and lubrication recommendations 0 9 6 Heater and air conditioner automatic if SO CQUIPPEC cscceccsesrerseesseestoees 4 11 Heater and air conditioner manual 4 3 Rear seat air conditioner seve 4 14 Air TOW Chan S isaisa 4 7 Alarm system See vehicle security EE rE AE ET Anti lock brake system ABS i Anti lock brake warning light 0 ANIMMNOSIS ccs5cicecsessetusdistenessetsetuansdurwersetteseodss Ashtray See cigarette lighter and ashtray secs cecesccatsscesscusccsescceycesveveevsenesscosctess 2 23 Audio system Compact disc CD player 4 30 4 32 FM AM radio with cassette player 4 20 FM AM radio with cassette player and compact disc CD player Autolamp SWItCH sa ccsccseceves crssieccreesecneseterseds Automatic Automatic power window switch 2 31 Automatic transmission fluid ATF 8 12 Driving with automatic transmission 5 6 Transmission selector lever lock NOIGASC E TT 5 7 B BAUS ys reinen e e sA 8 14 Battery replacement See remote keyless CMY SYSLOM iriiria Before starting the engine Brake Anti lock brake system ABS 5 14 Brake DOOSIEM s sicicesscaveevessddecevectesateveazs 8 22 Brake fluid Brake light Se
197. ive acid 6 10 In case of emergency PUSH STARTING CAUTION Automatic transmission models cannot be push or tow started This may cause transmission or other vehicle damage IF YOUR VEHICLE OVERHEATS If your vehicle is overheating indicated by an extremely high temperature gauge read ing or if you feel a lack of engine power detect abnormal noise etc take the follow ing steps A WARNING Do not continue to drive if your ve hicle overheats Doing so could cause a vehicle fire To avoid the danger of being scalded never remove the radiator cap while the engine is still hot When the radiator cap is removed pressurized hot water will spurt out possibly causing serious injury Do not open the hood if steam is coming out Move the vehicle safely off the road apply the parking brake and move the gearshift lever to the P Park position Do not stop the engine Turn off the air conditioner switch Open all the windows move the temperature control dial to warm and fan control dial to four 3 Get out of the vehicle Look and listen for steam or coolant escaping from the ra diator before opening the hood Wait until no steam or coolant can be seen before proceeding 4 Open the hood A WARNING If steam or water is coming from the engine stand clear to prevent getting burned 5 Visually check if the cooling fan is run ning The radiator hoses and radiator should not leak water If
198. ive for models manufac tured after April 1 1982 A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse the Instruments and controls 2 35 door does not meet current federal Your vehicle s engine should be turned safety standards Using a garage door Indicator off while programming your transmit opener without these features in ter The HomeLink Universal Trans creases the risk of serious injury or ceiver may not work with older garage death door openers that do not meet current Federal Consumer Safety Standards 1 Test the HomeLink Universal Trans ceiver by pressing any button The red indicator light should come on If you have previously programmed a button proceed to step 3 AIC1069 2 Clear all channels on the HomeLink Universal Transceiver by holding down PROGRAMMING HomeLink both outside buttons 1 amp 3 until the red light begins to flash rapidly approxi A WARNING mately 20 seconds Then release both During the programming procedure buttons your garage door or security gate will open and close if the transmitter is 3 Select which of the three HomeLink within range Make sure that people or Universal Transceiver buttons you want objects are clear of the garage door to program gate etc that you are programming 4 Hold your hand held transmitter against the bottom surface of the HomeLink Univer
199. k position the system may be deactivated when the key is re moved If the indicator light fails to glow for 30 seconds unlock the door once and lock it again Even when the driver and or passengers are in the vehicle the system will acti vate with all doors hood and rear door closed with the ignition key in the OFF position Vehicle security system operation The vehicle security system emits the fol lowing alarm e The headlights and tail lights flash and the horn sounds intermittently In addi tion the starter motor does not operate e The alarm automatically turns off after two to three minutes However the alarm reactivates if the vehicle is tampered with again The alarm can be shut off by unlocking a door with the key or by Instruments and controls 2 13 pressing the button on the multi remote controller The alarm is activated when e a door is unlocked or opened without using the key or the keyfob This includes unlocking the doors with the inside door lock switch the hood is opened e the ignition is placed into the ACC ON or START position without the key in the ignition How to stop the alarm The alarm stops only by unlocking a door with the key or by pressing the a button on the keyfob The alarm does not stop if the ignition key is turned to the ACC or ON position 2 14 Instruments and controls PRESS and hold buttons for two seconds AIC1037 Silencing the
200. ke your vehicle to the near est authorized NISSAN dealer A WARNING If the supplemental air bag warning light is on it could mean that the supplemental front air bag system will not operate in an accident Repair and replacement procedure The supplemental front air bag modules are designed to inflate on a one time only basis As a reminder unless it is damaged the supplemental air bag light remains illumi nated after inflation has occurred Repair and replacement of the air bag system should be done only by an authorized NIS SAN dealer When maintenance work is required on the vehicle the supplemental front air bag sys tem and related parts should be pointed out to the person conducting the maintenance The ignition key should always be in the LOCK position when working under the hood or inside the vehicle 1 38 Seats restraints and supplemental air bag systems A WARNING e Once the supplemental front air bag inflates the air bag module will not function again and should be re placed by an authorized NISSAN dealer The air bag module cannot be repaired e The supplemental front air bag sys tem should be inspected by an au thorized NISSAN dealer if there is any damage to the front end portion of the vehicle or replaced if the supplemental air bag has inflated e If you need to dispose of a supple mental air bag or scrap the vehicle contact an authorized NISSAN dealer Correct supplemental air bag dis
201. ks the drivers door and recalls the memory settings for both outside mirrors and drivers seat for that memory position Two keyfobs are delivered with the vehicle They can be programmed with the same memory drivers seat and mirror positions or each one can be programmed sepa rately One keyfob can be programmed for memory driver s seat and mirror position 1 and the other for memory driver s seat and mirror position 2 Memory Driver Seat and Mirror But tons The memory seat and mirror buttons are located on the driver door Pressing the memory driver seat and mirror position 1 or position 2 button will recall the memory set tings for both outside mirrors and driver seat for that memory seat position provided the vehicle is in P Park or N Neutral For easy vehicle exit press memory driver seat and mirror position 1 and position 2 buttons to gether to move the driver seat fully rearward and fully downward This function is preset and cannot be changed Programming Memory Positions 1 Move the driver seat and outside mirrors to the desired position using the manual controls 2 Push and hold the memory seat and mirror position 1 or position 2 button for at least 3 seconds e The indicator light will illuminate and re main illuminated until the position is pro grammed e After the position has been programmed the indicator light will flash to indicate the position is set The driver seat and or outside mirror
202. l and is not an indication of any malfunction If the com puter senses any malfunction it switches the anti lock brake system OFF and turns on the ABS brake warning light in the dash board The brake system then operates normally but without anti lock assistance If the light comes on during the self test or while driving take the vehicle to an authorized NISSAN dealer for repair A WARNING The anti lock brake system is a sophisticated device but it cannot pre vent accidents resulting from careless or dangerous driving techniques It can help maintain vehicle control during braking on slippery surfaces but re member that the stopping distance on slippery surfaces will be longer than on normal surfaces even with the anti lock brake system Stopping distances may also be longer on rough gravel or snow covered roads or if you are using tire chains Always maintain a safe dis tance from the vehicle in front of you Ultimately the responsibility for safety of self and others rests in the hands of the driver Tire type and condition of tires may also affect braking effectiveness e When replacing tires install the specified size of tires on all four wheels Starting and driving 5 15 e When installing a spare tire make sure it is the proper size and type as specified on the tire placard For tire placard location information refer to Tire placard in the Technical and consumer information section of
203. l the preset speed follow any of these three methods a Push the CANCEL button the SET light in the instrument panel goes out b Tap the brake pedal the SET light goes out c Push the cruise control OFF switch Both the main switch indicator and SET lights go out e If you depress the brake pedal while pushing the RES ACCEL switch the RES ACCEL function is cancelled In order for the RES ACCEL switch to operate the COAST SET must be used to re engage the system e The cruise control automatically cancels if the vehicle slows down more than 5 MPH 8 km h below the set speed e Move the selector lever to N Neutral The SET light goes out To reset at a faster cruising speed use one of the following three methods a Depress the accelerator pedal When the vehicle attains the desired speed push and release the COAST SET switch b Push and hold the RES ACCEL switch When the vehicle attains the speed you desire release the switch c Push and release the RES ACCEL switch Each time you do this the set speed increases by about 1 MPH 1 6 km h To reset at a slower cruising speed use one of the following three methods a Tap the brake pedal When the vehicle attains the desired speed push the COAST SET switch and release it b Push and hold the COAST SET switch Release the switch when the vehicle slows down to the desired speed c Push and release the COAST SET switch Each time you do th
204. l vent WiINdOWS eeceeseeeeeseeeeeneeees 2 32 Sunroof if SO CQUIPPEd ee eee eeetetteeteteeeeeeeee 2 33 Interior ONS aineinaan 2 34 LUG GAG C senssa 2 34 Personal reading light ee eeeseeeeeeeeeneeeeeeees 2 34 Map Hg AtS eeen ionainn 2 35 lluminated entry system eee eeeeeeeneeeeees 2 35 HomeLink universal transceiver if SO CQUIPPO siirinsesi seinni Programming HomeLink cceeeeeeee Programming HomeLink for Canadian CUSLOM CIS se a ee ea eae E ETES Operating the HomeLink universal TrANSCEIVEL eceeceeeeeecceeeeeeeeteeeeeeeeeneeeeeeeeenneees Programming trouble diagnosis 0006 2 37 Clearing the programmed information 2 38 Rolling code programming sesser 2 38 If your vehicle is ever stolen ee 2 39 WIC0148 2 2 Instruments and controls ON OAR WD pe es ee eo A U MD O 15 16 17 18 19 Horn Meters gauges Gear shift selector lever Hazard warning flasher switch Rear window washer switch Rear window wiper switch Rear window defogger switch Security light Center ventilators Passenger supplemental air bag Side ventilator Glove box FM AM radio with cassette player FM AM radio with cassette player and CD player Map pocket if so equipped Heater air conditioner controls Storage compartment Cup holders CD changer if s
205. lar phone in or near the vehicle may influence radio reception quality Power Volume control Push the VOL knob to turn the radio on Push the VOL knob once more to turn the radio OFF The control buttons are illuminated when the parking lamps or headlamps are on Only the text for the active controls will illuminate for each specific type of media No bulbs or lights have malfunctioned For example when a cassette tape is being played SHUFFLE will not illuminate Turn the knob to the right to increase vol ume or to the left to decrease volume If the knob is set above a certain volume level and the ignition is turned off the volume will come back on at a nominal listening level when the ignition is turned back on Adjusting tone quality and speaker bal ance Bass Bass control allows you to adjust the lower bass frequencies to your preference Push the BASS button and the setting indi cator bar appears in the display window Pressing the SELECT button either lt or increases or decreases the level of bass as indicated by the number of bar segments showing in the display window Following bass adjustment the display win dow shows the current setting for three seconds then returns to the display prior to adjustment 4 26 Heater air conditioner and audio systems Treble Treble control allows you to adjust the higher treble frequencies to your preference Push the TREB button and the setting indi cator
206. laying the cassette or com pact disc Using RDS to search for programming type Certain areas have a limited number of stations that transmit RDS Many stations transmit call letters and frequencies only Searching or scanning by program type may yield a limited number of selections Press the RDS CLK button until FIND CLASSIC is displayed then use the SEL button to choose between CLASSIC COUNTRY INFO JAZZ OLDIES R amp B RELIGUS Religious ROCK SOFT and TOP40 When you have chosen a program type use the SEEK SCAN or AUTOSET controls to look for a station transmitting that kind of program If the radio searches through the whole band and then returns to the previous station it was originally playing there are no stations in the area that are Heater air conditioner and audio systems 4 23 transmitting that type of programming Cassette tape player operation Turn the ignition to ACC or ON and care fully insert a cassette tape into the tape door The cassette tape automatically pulls into the player and begins to play When a casssette is inserted into the audio system the word TAPE and a cassette side symbol either one or two illuminates in the display If the radio is already operating it automati cally turns off and the cassette tape begins to play The cassette tape automatically changes direction to play the other side when the first side is complete PLAY STOP Push the AM or FM buttons while the cas
207. ld 7 4 Appearance and care soap solution Allow the belts to dry com pletely before using them amp WARNING Do not allow wet seat belts to roll up in the retractor NEVER use bleach dye or chemical solvents to clean the seat belts since these may severely weaken the seat belt webbing CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION 1 The accumulation of moisture retaining dirt and debris in body panel sections cavities and other areas 2 Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents ENVIRONMENTAL FACTORS IN FLUENCE THE RATE OF COR ROSION Moisture Accumulation of sand dirt and water on the vehicle body underside can accelerate cor rosion Wet floor coverings do not dry com pletely inside the vehicle and should be removed for drying to avoid floor panel corrosion Relative humidity Corrosion will be accelerated e in areas of high relative humidity e in areas where the temperatures stay above freezing where atmospheric pollution exists where road salt is used Temperature A temperature increase accelerates the rate of corrosion to those parts which are not well ventilated Air pollution Industrial pollution the presence of salt in the air in coastal areas or heavy road salt use accelerates the corrosion process Road salt also accelerates the disintegra tion of paint surfaces TO P
208. ld be injured 1 Detach the single window seat belt tongue from the auxiliary buckle mounted to the side of the seat and store the tongue out of the way For detailed infor mation see Two buckle seat belt sys tem for the second row bench seat later in this section 2 Lift up the recliner lever 3 Fold the seatback fully forward 4 Unlock the seat legs at the two rear floor latch levers by pulling up on the two straps 5 Lift the back of the seat 6 Slide the seat rearward off the front an chor positions Installing the second row bench seat POSITION seat leg hooks Installing the second row bench seat Clean the area around the seat leg floor anchors before installing the seat 1 With the seatback fully folded place the seat behind the floor anchors and catch the seat leg hooks into each floor anchor 2 Push down on the back of the seat to secure the two rear floor latches 3 Lift up the recliner lever and raise the seatback 4 Rock the seat back and forth to be sure ATTACH tongue to buckle ARS1140 all four seat legs are securely latched 5 Insert the single window seat belt tongue into the auxiliary buckle mounted to the side of the seat Seats restraints and supplemental air bag systems 1 13 Removing second row bucket seats amp WARNING Do not remove or install seats while the vehicle is moving After adjustment gently rock in the seat to make sure
209. ldren unattended in side the vehicle They could unknow ingly activate switches or controls and become trapped in a window Unattended children could become involved in serious accidents D it h Driver side switc N N Y Driver s side automatic X Left rear vent window sa switch Window lock aN Door lock Right PUSH LIFT unlock rear vent to open to close button window Front passenger AIC1079 The main switch on the driver side opens or closes the driver s and passenger s win dows and if so equipped rear vent win dows To open the window press the switch down To close the window lift the switch up The power windows operate when the igni tion key is in the ON position or for 15 minutes after the ignition key is turned to the OFF position If the driver s or passenger s door is opened during this 15 minute period power to the windows is cancelled Locking passenger s window When the power window lock out button is pushed in the passenger s window cannot be opened or closed Push the power win dow lock out button again to cancel this feature Driver side switch automatically open window ___ J DEPRESS switch to T ae N Be AIC1080 Automatic operation To fully open the driver side window press down firmly on the switch and release it you do not need to hold the switch down The window auto
210. le to the left and right AUDIO jacks 3 Press the MEDIA button to activate the AUX mode The LCD screen will turn on and the AUX indicator will illuminate 4 If desired press the speaker control but ton and plug a headphone into the head phone jack With the headphones ON the rear speakers will not operate LHA0089 Removing and installing VCP Press down on the release lever and care fully pull up on the VCP To install carefully slide the VCP into the case until you hear it click into place Do not force the VCP into the console Make sure no objects are in the console prior to installation Security screw LHA0095 NOTE The FES may be equipped with a secu rity screw If you have difficulty remov ing the VCP check to see if the security screw is installed The security screw is located on the driver s side of the con sole near the floor The security screw can be removed using a tamper resistant Torx bit size T20 If you need assis tance please see your Nissan dealer LHA0093 REAR SEAT ENTERTAINMENT MODULE RSEM if so equipped amp WARNING The driver must not attempt to operate the RSEM while the vehicle is in motion so that full attention may be given to vehicle operation The RSEM is automatically activated when the vehicle ignition and radio are both turned ON The headphones symbol illumi nates in the front radio display wh
211. leaner as soon as possible e Keep coolant out of reach of children and pets ENGINE OIL iy OA Engine oil dipstick 2 O ADI1084 CHECKING ENGINE OIL LEVEL 1 Park the vehicle on a level surface and apply the parking brake 2 Start the engine and let it idle until it reaches operating temperature 3 Turn the engine off Wait a few minutes for the oil to drain back into the oil pan 4 Remove the dipstick and wipe it clean Reinsert it all the way Overfull a p Add Normal range ADI0009 5 Remove the dipstick again and check the oil level It should be between the H High and L Low marks If the oil level is below the L Low mark remove the oil filler cap and pour recommended oil through the opening Do not overfill 6 Recheck the oil level with the dipstick It is normal to add some oil between oil maintenance intervals or during the break in period depending on the sever ity of operating conditions Maintenance and do it yourself 8 9 CAUTION Oil level should be checked regularly Operating with an insufficient amount of oil can damage the engine and such damage is not covered by warranty 8 10 Maintenance and do it yourself Oil filler Front ADI0057 LOOSEN CHANGING ENGINE OIL i Park the vehicle on a level surface and apply the parking brake Start the engine and let it idle until it
212. lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied Automatic transmission P Park posi tion mechanism Check that the lock re lease button on the selector lever operates properly and smoothly On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes Under the hood and vehicle The maintenance items listed here should be checked periodically e g each time you time you check the engine oil or refuel Additional information on the following items with an is found later in this section Windshield washer fluid Check that there is adequate fluid in the reservoir Engine oil level Check the level after parking the vehicle on a level surface with the engine off Wait a few minutes for the oil to drain back into the oil pan Brake and clutch fluid level Make sure that the brake and clutch fluid level is be tween the MIN and MAX lines on the reser voir Power steering fluid level and lines Check the level when the fluid is cold with the engine off Check the lines for proper attachment leaks cracks etc Automatic transmission fluid level Check the level after putting the selector lever in P with the engine idling at operating temperature Engine coolant level Check the coolant level when the engine is cold Radiator and hoses Check the front o
213. lly raise the vehicle until the tire clears the ground To lift the vehicle securely hold the jack lever and rod with both hands as shown above Remove the wheel nuts and then remove the tire 6 6 In case of emergency ACE1031 CE1003 Installing the spare tire The spare tire is designed for emergency use See specific instructions under the heading Wheels and tires in the Main tenance and do it yourself section of this manual 1 Clean any mud or dirt from the surface between the wheel and hub 2 Carefully put the wheel on and tighten the lug nuts finger tight 3 With the lug wrench tighten the lug nuts alternately and evenly until they are tight 4 Lower the vehicle slowly until the tire touches the ground Then with the lug wrench tighten the lug nuts securely in the sequence as illustrated Lower the vehicle completely A WARNING e Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off This could cause an accident e Do not use oil or grease on the wheel studs or nuts This could cause the nuts to become loose e Retighten the wheel nuts when the vehicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc As soon as possible tighten the lug nuts to the specified torque with a torque wrench Lug nut tightening torque 80 ft lb 108 N m Adjust tire
214. load equals trailer weight plus its cargo weight Towing loads greater than 3 500 Ibs 1 588 kg or using improper towing equipment could adversely affect vehicle handling braking and performance e All towing above 1 000 Ibs 454 kg re quires the use of trailer brakes NISSAN recommends the use of a tan dem axle trailer whenever towing above 3 000 Ibs 1 361 kg e A sway control device is recommended for all towing above 2 000 Ibs 907 kg Sway control devices are not offered by NISSAN See a professional trailer hitch outlet for a properly designed sway con trol device for your trailer The Gross Combined Weight should not exceed 8 000 Ibs 3 628 kg The Gross Combined Weight is the total weight of the tow vehicle with all occupants cargo and fuel tanks PLUS the total weight of the trailer and all its cargo This weight should be properly distributed For more informa tion regarding vehicle and trailer loading refer to The NISSAN Towing Guide avail able from an authorized NISSAN dealer The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads but also the places you plan to tow Tow weights appropriate for level highway driving may have to be reduced on very steep grades or in low traction situations for example on slippery boat ramps A WARNING Vehicle damage and or personal injury resulting from improper towing proce dures are not covered by NISSAN war ranties
215. lows mainly from center and side A C ventilators outlets CES Air flows mainly from center and side ventilators Air flows from center and side ventila tors and the front and rear foot outlets Heater air conditioner and audio systems 4 3 OFF position The OFF position shuts off the air supply to all outlets and stops all fan operations Use the OFF position to prevent cold air from entering the passenger compartment under cold outside conditions before the engine is warmed up MAX A C Position Interior air is recirculated inside the vehicle Turn the air control dial to the MAX A C position when driving on a dusty road or to help keep out traffic fumes Turn the air control dial to the MAX A C position for improved air conditioner perfor mance under high temperature and high hu midity conditions amp CAUTION Do not use the recirculation mode for long periods as it may cause the inte rior air to become stale and the win dows to fog up Temperature control dial This dial allows you to adjust the tempera ture of the outlet air Air conditioning button Start the engine turn the fan control dial to the desired one to four position select an air control position and push the air condi tioner button to turn on the air conditioner The indicator light comes on when the air conditioner is operating To stop the air con ditioner push the button again the indicator light goes off The air c
216. ls toward the curb and move the vehicle forward until the curb side wheel gently touches the curb HEADED UPHILL WITH CURB Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb HEADED UPHILL OR DOWNHILL NO CURB Turn the wheels toward the side of the road so the vehicle will move away from the center of the road if it moves Turn the ignition key to the LOCK posi tion and remove the key Starting and driving 5 13 POWER STEERING The power assisted steering is designed to use a hydraulic pump driven by the engine to aid steering If the engine stops or the drive belt breaks you still have control of the vehicle How ever much greater steering effort is needed especially in sharp turns and at low speeds A WARNING If the engine is not running or is turned off while driving the power assist for the steering will not work Steering will be much harder to operate 5 14 Starting and driving BRAKE SYSTEM The brake system has two separate hydrau lic circuits If one circuit malfunctions you will still have braking at two wheels BRAKING PRECAUTIONS Vacuum assisted brake The brake booster aids braking by using engine vacuum If the engine stops you can stop the vehicle by depressing the brake pedal However greater foot pressure on the brake pedal is required to stop the vehicle and the stopping distance is longer Using the brak
217. m Air bag system for the front passen ger For precautions see Supplemenial restraint system earlier in this section Infants and small children NISSAN recommends that infants and small children be placed in a child restraint that complies with the Federal Motor Vehicle Safety Standards or Canadian Motor Ve hicle Safety Standards You should choose a child restraint that fits your vehicle and always follow the manufacturer s instruc tions for installation and use Larger children Children who are too large for child re straints should be seated and restrained by the seat belts which are provided If the child s seating position has a shoulder belt that fits close to the face or neck the use of a booster seat commercially available may help overcome this The booster seat should raise the child so the shoulder belt is properly positioned across the top middle portion of the shoulder and the lap belt is low on the hips The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Ve hicle Safety Standards Once the child has Seats restraints and supplemental air bag systems 1 41 grown enough so the shoulder belt is no longer on or near the face and neck use the shoulder belt without the booster seat A WARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the ve
218. matic locking mode do not use the integrated child safety seat and have it inspected by an authorized NISSAN dealer To cancel the automatic locking mode un buckle the chest clip and both shoulder harness tongues Allow the shoulder har nesses to retract completely The automatic locking mode is now canceled and the shoulder harness retractor is in the emer gency locking mode A WARNING The automatic locking mode child re straint mode must be reactivated each time you place a child in the integrated child safety seats In addition to the automatic locking retrac tors the integrated child safety seat shoul der harnesses are equipped with emer gency locking retractors The automatic locking mode is best to use especially for children who need help staying properly positioned in the seat and its harnesses for example children who are younger and smaller because the belts are always locked In the emergency locking mode the shoulder belts only lock in a sudden stop or accident allowing a child more freedom of movement Use the emergency locking mode only if you judge your child able to remain properly positioned in the integrated child safety seat Removing the child 1 Release the chest clip 2 Release the left and right shoulder har ness tongues from the belt buckle by pressing the red belt buckle button 3 Move the left and right shoulder har nesses aside and assist the child from the integrated chil
219. matically opens all the way The automatic feature can be interrupted before the window is fully open by briefly lifting up on the switch as the window moves down Instruments and controls 2 31 Passenger side switch pushl to open 5 AIC1081 The passenger side switch opens or closes the passenger window only To open the window press the switch down To close the window lift the switch up 2 32 Instruments and controls Driver s side SN m vent window switch LIFT to lt open See a Right vent window switch 1 ae AIC1067 POWER VENT WINDOWS if so equipped Use the vent window switches on the driv er s side window controls to open and close the power vent windows To open one of the power vent windows press the switch down To close the window lift the switch up The power vent windows operate when the ignition key is in the ON position or for 15 minutes after the ignition key is turned to the OFF position If the driver s or passenger s door is opened during this 15 minute period power to the vent windows is cancelled MANUAL VENT WINDOWS To open the manual vent windows pull the rear portion of the latch toward you until it releases To lock the window in the open position push the latch rearward until you hear it latch To close the windows pull the latch toward you and push the rear portion of the latch toward the rear of the vehicle unt
220. may blink when the CRUISE main switch is turned ON while pushing either 5 10 Starting and driving the RES ACCEL COAST SET or the CANCEL switch located on the steering wheel To properly set the cruise control system perform the steps in the order indicated A WARNING Do not use the cruise control when driving under the following conditions e When it is not possible to keep the vehicle at a set speed e In heavy traffic or in traffic that var ies in speed e On winding or hilly roads e On slippery roads rain snow ice etc In very windy areas Doing so could cause a loss of vehicle control and result in an accident CRUISE CONTROL OPERATIONS The cruise control allows driving at speeds between 29 and 90 MPH 47 and 144 km h without keeping your foot on the accelerator pedal To turn the cruise control on push the CRUISE main switch The indicator light on the switch comes on To set at cruising speed accelerate your vehicle to the desired speed push the COAST SET switch and release it The SET light in the instrument cluster comes on Take your foot off the accelerator pedal Your vehicle maintains the set speed e To pass another vehicle depress the accelerator pedal When you release the pedal the vehicle returns to the previ ously set speed e The vehicle may not maintain the set speed when going up or down steep hills If this happens drive without the cruise control To cance
221. mer with a vehicle that is built with quality and craftsmanship a product that we can be proud to build and you can be proud to own NISSAN CUSTOMER CARE PROGRAM NISSAN CARES Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns Your NISSAN dealer is always available to assist you with all your automobile sales and service needs However if there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions please con tact our NISSAN s Consumer Affairs De partment using our toll free number For U S mainland and Alaska customers 1 800 NISSAN 1 1 800 647 7261 For Hawaii customers 808 836 0888 Oahu Number For CANADIAN customers 1 800 387 0122 The Consumer Affairs Department will ask for the following information Your name address and telephone number Vehicle identification number Attached to the top of the instrument panel on the driver s side Date of purchase Current odometer reading Your NISSAN dealer s name Your comments or questions OR you may write to NISSAN with the information on the left at For U S mainland and Alaska custom ers Nissan North America Inc Consumer Affairs Department P O Box 191 Gardena California 90248 0191 For Hawaii customers Nissan Motor C
222. mission Fluid Dexron III Mercon or equivalent may also be used Out side the continental United States and Alaska contact a Nissan dealership for more information regarding suitable fluids including recommended brand s of Dexron IIl Mercon NOTE If the vehicle has been driven for a long time at high speeds or in city traffic in hot weather or if it is being used to pull a trailer the accurate fluid level cannot be read You should wait until the fluid has cooled down about 30 minutes POWER STEERING FLUID BRAKE FLUID Power steering fluid reservoir ADI1086 Check the fluid level in the reservoir The fluid level should be checked by looking at the MAX and MIN lines at fluid tempera tures of 32 F to 86 F 0 C to 30 C If the fluid is below the MIN line add auto matic transmission fluid type F up to the MAX line amp CAUTION e DO NOT OVERFILL e The recommended fluid is type F automatic transmission fluid or equivalent Brake fluid reservoir Check the fluid level in the reservoir If the fluid is below the MIN line or the brake warning light comes on add DOT 3 fluid up to the MAX line If fluid must be added frequently the system should be thoroughly checked by an authorized NISSAN dealer For further brake fluid specification informa tion refer to the Technical and Consumer Information section in this manual Maintenance and do it yourself
223. most effective when you are sitting back and upright in the seat Front air bags inflate with great force If you are unrestrained leaning forward sitting sideways you are at greater risk of injury or death in a crash You may also receive serious or fatal injuries from the supplemental front air bag if you are up against it when it inflates Always sit back against the seatback and as far away as practical from the steering wheel or instrument panel Always use the seat belts Keep hands on the outside of the steer ing wheel Placing them inside the steering wheel rim could increase the risk that they are injured when the supplemental front air bag inflates Seats restraints and supplemental air bag systems 1 31 1 32 Seats restraints and supplemental air bag systems A WARNING e Never let children ride unrestrained Do not attempt to hold them in your lap or arms Some examples of dan gerous riding positions are shown in the illustrations e Children may be severly injured or killed when the supplemental front air bag inflates if they are not prop erly restrained e Never install a rear facing child re straint in the front seat An inflating supplemental front air bag could se riously injure or kill your child See Child restraints later in this sec tion for details ARS 1044 ARS 1046 Seats restraints and supplemental air bag systems 1 33
224. n aural reception FM AM Radio operation MUTE button Push the MUTE button to mute out the radio TUNE buttons lt 1 gt A WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation Use the lt Q or gt buttons for manual tuning To move quickly through the chan nels hold either of the tune buttons down for more than 0 5 seconds Heater air conditioner and audio systems 4 27 AUTO SET Press the AUTO button while listening to the radio to activate the auto set feature When AUTO is depressed for less than 5 seconds the display window momentarily indicates AUTO ON and the radio seeks the first six strong stations for the respective band The first six strong stations are then stored in order in memory buttons one through six Only stations in the selected band are set and the station seek begins from the last frequency stored in memory button six If AM FM SCAN TUNE SEEK AUTO or a memory button is pushed while auto set is operating auto set is canceled and AUTO OFF shows in the display window AUTO LOAD Press the AUTO button for longer than 5 seconds while listening to the radio to acti vate the auto load feature When AUTO is depressed for longer than 5 seconds the display window momentarily indicates AUTO LOAD and the radio seeks the first six strong stations for every band The first six strong stations are then stored in order in memory buttons one
225. n 15 minutes without starting the engine i Eject Rewind Stop display button button button LHA0090 Video Cassette Player VCP con trols The VCP has the following controls e LED display The display lamp will illuminate when power is supplied to the VCP e Power button Press to turn the VCP ON or OFF When the power is ON the other buttons will illuminate e PLAY button Press to play a videocas sette tape e REWIND REVIEW button When in 4 38 Heater air conditioner and audio systems PLAY mode pressing the button re verses the picture When in STOP mode the videocassette tape will rewind at high speed FAST FORWARD CUE button When in PLAY mode pressing the button for wards the picture When in STOP mode the videocassette tape will fast forward at high speed STOP button Press to stop the video cassette tape HEADPHONE VOLUME buttons Press to adjust the headphone volume Home use only EJECT button Press to eject the vid eocassette tape e RETRACKING button Press to activate extremely close distances to the FES or not Power tS a Auto Tracking at all a ifs Encore e TRACKING button Press for manual eo ae button tracking adjustment button bead Retracking Tracking Il fee AV button e TRACKING button Press for manual purton EA Tracking tracking adjustment Rew
226. n a regular radio broadcast Most RDS stations are currently in large cities but many stations are now considering broadcasting RDS data RDS can display e Station name or call sign such as WHER 98 3 e Music or programming type such as Classical Country or Rock e Traffic reports about delays or construc tion Using RDS To turn RDS on push the RDS CLK button until RDS OFF is displayed then press the SEL button until RDS ON is displayed To change display type turn RDS ON then use the SEL button to choose between e SHOW TYPE Music or program type e SHOW NAME Station name or call sign e SHOW NONE No text display To choose traffic reports press the RDS CLK button until TRAFFIC OFF is dis played the use then SEL button to choose TRAFFIC ON then use the seek or scan control to look for a station that may transmit traffic reports the radio will display a TRAF icon to show it is in traffic mode and tuned to a station that may transmit traffic reports If the radio searches through the whole band and then returns to the previous station it was originally playing there are no stations in the area that are transmitting traffic reports If a cassette or compact disc is being played while the traffic option is on and the station previously tuned into displays a traffic bul letin the radio will pause the cassette or compact disc and broadcast the bulletin then resume p
227. n autho rized NISSAN dealer Always confirm proper vehicle and trailer stop turn lamp operation every time the trailer light circuits are con nected for use Technical and consumer information 9 17 Trailer brakes If your trailer is equipped with a braking system make sure it conforms to Federal and or local regulations and it is properly installed amp WARNING Never connect a trailer brake system directly to the vehicle brake system Pre towing tips e Be certain your vehicle maintains a level position when a loaded and or unloaded trailer is hitched Do not drive the vehicle if it has an abnormal nose up or nose down condition check for improper tongue load overload worn suspension or other possible causes of either condi tion e Always secure items in the trailer to prevent load shift while driving e Becertain your rear view mirrors conform to all federal state or local regulations If not install any mirrors required for towing before driving the vehicle Trailer towing tips In order to gain skill and an understanding of the vehicle s behavior you should prac tice turning stopping and backing up in an area which is free from traffic Steering stability and braking performance are somewhat different than under normal driv ing conditions e Always secure items in the trailer to prevent load shift while driving Avoid abrupt starts acceleration or stops Avoid sharp turns or lane chang
228. n the a button 2 Replace the battery with a new one two or three times to check the keyfob Insert the batteries as illustrated above operation Recommended battery Panasonic CR2025 3V or equivalent 8 24 Maintenance and do it yourself If the batteries are removed for any reason other than replacement perform step 4 e An improperly disposed battery can hurt the environment Always conform to local regulations for battery disposal e The keyfob is water resistant how ever if it does get wet immediately wipe completely dry e The operational range of the keyfob extends to approximately 30 ft 10 m from the vehicle This range may vary with conditions FCC Notice Changes or modifications not expressly approved by the manufacturer for com pliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules and RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation of the device LIGHTS Headlamp reflector Glass envelope Bulb 4 S77 PUSH to remove J je Bulb socket Plastic base UNLOCK Harness connector Bulb retaining ring AELO76 A HEADLIGHTS The headlight is a semi sealed beam type which uses a replaceable headlight
229. na cargo area inside of a vehicle In a collision people riding in these ar eas are more likely to be seriously injured or killed Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts Be sure everyone in your vehicle is in a seat and using a seat belt prop erly Be sure to replace and reposition floor mats as discussed in Floor mat positioning in this section The three passenger sliding bench seat is not intended to be removed from the vehicle by consumers However if it must be removed have a qualified person remove it That person should refer to the instruc tions in the service manual When seat is reinstalled the attaching bolts must be tightened to the appro priate torque specifications Failure Seats restraints and supplemental air bag systems 1 9 to follow these instructions could increase the chance and or severity of injury in an accident Cleaning the seat tracks The seat tracks for the three passenger sliding bench seat should be cleaned peri odically with a high powered vacuum cleaner Dirty seat tracks may reduce the sliding ability of the seat A wet cleansing agent may be used if necessary but the seat tracks must be thoroughly dried Use a cloth wrapped around a screwdriver or similar object to clean the seat tracks Do not use your fingers to clean debris from the tracks Do not apply any type of lubricant to the seat tracks A
230. nch TURN counterclockwise to lower spare tire PULL back the carpet Spare tire hex nut ACE1026 1 Locate the cut in the carpet for the hex nut in the the cargo area The hex nut is used to lower and raise the spare tire located underneath the vehicle 2 Place the lug wrench over the hex nut and turn counterclockwise until the cable extends completely The spare tire hex nut rachets when the cable is fully ex tended Spare tire 3 Carefully slide the tire from under the rear of the vehicle In case of emergency 6 3 DN VAN LLRI C SS a SS oe TEE yak i A i REMOVE spare tire retainer 2 ACE0014 4 Stand the tire up to remove the retainer 6 4 In case of emergency Jack rod Wheel cover ACE1023 Removing wheel cover Remove the jack rod from the jack storage bag For wheel cover removal place the screwdriver tip of the jack rod between the wheel cover and the edge of the rim Push and twist gently amp CAUTION Do not use your hands to pry off wheel caps or wheel covers Doing so could result in personal injury Jack rod Wheel cap ACE1022 Removing wheel cap For cap removal place the screwdriver tip of the jack rod into the indentation between the cap and the wheel Push and twist gently ACE1021 Vehicle jack up points ACE1030
231. ncludes those items which should be checked during normal 8 2 Maintenance and do it yourself day to day operation of the vehicle They are essential if your vehicle is to continue to operate properly It is your responsibility to perform these maintenance procedures regularly as prescribed Performing general maintenance checks re quire minimal mechanical skill and only a few general automotive tools These checks or inspections can be done by yourself a qualified technician or if you prefer an authorized NISSAN dealer Where to go for service If maintenance service is required or your vehicle appears to malfunction have the systems checked and tuned by an autho rized NISSAN dealer NISSAN technicians are well trained spe cialists who are kept up to date with the latest service information through technical bulletins service tips and in dealership training programs They are completely qualified to work on NISSAN vehicles be fore they begin work on your vehicle rather than after they have worked on it You can be confident that an authorized NISSAN dealer s service department per forms the best job to meet the maintenance requirements on your vehicle in a reliable and economic way GENERAL MAINTENANCE During the normal day to day operation of the vehicle general maintenance should be performed regularly as prescribed in this section If you detect any unusual sounds vibrations or smells be sure to
232. nd year of manu facture Vehicle Identification Number VIN etc Review it carefully EMISSION CONTROL INFORMATION LABEL The emission control information label is attached as shown Technical and consumer information 9 11 INSTALLING FRONT LICENSE PLATE TIRE PLACARD AIR CONDITIONER The cold tire pressure is shown on the tire SPECIFICATION LABEL placard affixed to the inside of the glove 3 The air conditioner specification label is OX attached as shown ATI0564 Have your front license plate installed by your NISSAN dealer 9 12 Technical and consumer information VEHICLE LOADING INFORMATION A WARNING e It is extremely dangerous to ride ina cargo area inside the vehicle In a collision people riding in these ar eas are more likely to be seriously injured or killed e Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts e Be sure everyone in the vehicle is ina seat with their seat belt properly fas tened TERMS It is important to familiarize yourself with the following terms before loading your vehicle e Curb Weight actual weight of your ve hicle vehicle weight including standard and optional equipment fluids emergency tools and spare tire assembly This weight does not include passengers and cargo e GVW Gross Vehicle Weight curb weight plus the combined weight of pas sengers and cargo
233. ne thinner or any similar ma terials If any abnormalities are found or the heated seat does not operate turn the switch off and have the system checked by your NISSAN dealer e The battery could run down if the seat heater is operated while the engine is not running Instruments and controls 2 21 REAR POWER SOCKET FLIP lid to open a The rear power socket is located on the driver s side trim panel of the second row seat behind the side door Open the cover to gain access to the power socket There are two power sockets located on the Family Entertainment System FES if so equipped Use the power socket to plug in electrical equipment such as a cellular telephone CB radio etc Follow the installation instructions included with your electrical equipment When not in use always close the power socket cover 2 22 Instruments and controls 7 XN Ss WICO019 CAUTION When using the power socket e Maximum load of any electrical equipment should not exceed 10 amps e Be sure to turn off any electrical equipment when not in use Leaving electrical equipment on for extended periods can discharge your battery Power sockets LIC0087 CIGARETTE LIGHTER AND ASHTRAY accessory A ET r ry 5 Sisarett lighter C o ee cg Fs r jac Utility tray PULL out to access AIC1074 7 y l PULL on lid to T remove ash tray
234. ner removed and be careful when working on the engine with the air cleaner removed Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed Doing so could result in serious injury 8 18 Maintenance and do it yourself WINDSHIELD WIPER BLADES Lift up the wiper blade f Remove the wiper blade NI ON ADI1022 CLEANING If your windshield is not clear after using the windshield washer or if the wiper blade chatters when running wax or other mate rial may be on the blade or windshield Clean the outside of the windshield with a washer solution or a mild detergent Your windshield is clean if beads do not form when rinsing with clear water Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter gent Then rinse the blade with clear water If your windshield is still not clear after cleaning the blades and using the wipers replace the blades amp CAUTION Worn windshield wiper blades can damage the windshield and impair driver vision REPLACING Replace the wiper blades if they are worn 1 Lift the wiper arm away from the windshield 2 Push the tab then move the wiper blade down the wiper arm to remove 3 Remove the wiper blade 4 Insert the new wiper blade onto the wiper arm until it clicks into place CAUTION e After wiper blade replacement return the wiper arm
235. ng brake 2 Move the selector lever to P Park or N Neutral P is recommended The shift selector lever cannot be moved out of P and into any of the other gear positions under the follow ing conditions e The ignition key is turned to the LOCK position e The ignition key is turned to the ON position without depressing the foot brake pedal The starter will not operate if the shift selector lever is in one of the driving positions Crank the engine with your foot off the accelerator pedal by turning the ignition key to START Release the key when the engine starts If the engine starts but fails to run repeat the above procedure If the engine is very hard to start in extremely cold or hot weather de press the accelerator pedal to the floor and hold it to help start the engine Starting and driving 5 5 In the summer when restarting the engine within 30 minutes after it has been stopped keep the accelerator pedal slightly depressed while start ing amp CAUTION Do not operate the starter for more than 15 seconds at a time If the engine does not start turn the key off and wait 10 seconds before cranking again other wise the starter could be damaged 4 Warm up Allow the engine to idle for at least 30 seconds after starting Drive at moderate speeds for a short distance first espe cially in cold weather 5 6 Starting and driving DRIVING THE VEHICLE A WARNING e Do not de
236. ng provides two circuits right and left hand to operate trailer stop turn tail lamps Each individual stop turn circuit will operate only one com bination stop turn light bulb 1157 3157 2357 or 3357 on the trailer Never add more than one trailer light bulb to one circuit SAE J1239 connector To trailer Connector Vehicle a end Tow harness connector To vehicle harness ATI0555 Trailer tow harness and module if so equipped The trailer tow module on your vehicle al lows turn stop lamp control of a trailer being towed by your NISSAN The trailer tow module includes trailer tow module which draws power from the vehicle stop lamp fuse one subharness containing a SAE J1239 specified connector To use the tow harness 1 Remove the connector cap from the vehicle harness located behind the rear bumper Store the connector cap in ve hicle glove box for reinstallation 2 Connect the tow harness to the vehicle harness located behind the rear bumper 3 Connect the tow harness connector SAE J1239 to your trailer 4 Confirm proper vehicle and stop turn lamp operation trailer 5 When towing is completed disconnect the tow harness from the trailer and the vehicle Store the tow harness in the glove box Reinstall the connector cap to the vehicle harness If you need further assistance in wiring a trailer to your NISSAN contact a
237. ning light is on it could mean that the supplemental air bag will not operate in an accident Low washer fluid warning light This light comes on when the washer fluid is at a low level Add washer fluid as neces sary See the Maintenance and do it yourself section of this manual BRAKE Q Brake warning light This light functions for both the parking brake and the foot brake systems When the ignition key is in the ON position the light comes on when the parking brake is applied and also warns of a low brake fluid level If the light comes on while the engine is running with the parking brake not Instruments and controls 2 9 applied stop the vehicle and perform the following 1 Check the brake fluid level Add brake fluid as necessary See Brake fluid in the Maintenance and do it yourself section of this manual 2 If the brake fluid level is correct have the warning system checked by an autho rized NISSAN dealer amp WARNING e Your brake system may not be work ing properly if the warning light is on Driving could be dangerous If you judge it to be safe drive care fully to the nearest service station for repairs Otherwise have your ve hicle towed because driving it could be dangerous e Pressing the brake pedal with the engine stopped and or low brake fluid level may increase your stop ping distance and braking will re quire greater pedal effort as well as
238. ning lights will remain on until the ignition switch is turned OFF WARNING When the daytime running light system is active tail lights on your vehicle will not be on It is necessary at dusk to turn on your headlights Failure to do so could cause an accident injuring yourself and others Instruments and controls 2 17 Headlight switch Of PUSH INTERIOR AIC1058 AUTOLAMP SWITCH if so equipped The autolamp system allows the headlights to be set so they turn on and off automati cally The autolamp system can turn on the headlights automatically when it is dark turn off the headlights when it is light and keep the headlights on for up to three minutes after you turn the key to OFF To set the autolamp system 1 Make sure the headlight switch is in the AUTO1 or AUTO2 position 2 18 Instruments and controls 2 Turn the ignition key to ON 3 The autolamp system automatically turns the headlights on and off Shut off delay The length of time the headlights stay on after the ignition is turned to OFF depends on whether the switch is in the AUTO1 or AUTO2 position If the switch is in the AUTO1 position then the headlights stay on for less than 1 minute after the ignition is turned OFF If the switch is in the AUTO2 position the headlights stay on approxi mately 3 minutes after the ignition is turned OFF To turn the autolamp system off turn the switch to the OFF a or D p
239. nny days temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals EXHAUST GAS Carbon Monoxide A WARNING Do not breathe exhaust gases they contain colorless and odorless carbon monoxide Carbon monoxide is dan gerous It can cause unconsciousness or death e If you suspect that exhaust fumes are entering the vehicle drive with all windows fully open and have the vehicle inspected immediately e Do not run the engine in closed spaces such as a garage 5 2 Starting and driving e Do not park the vehicle with the en gine running for any extended length of time e Keep the rear door and rear window closed while driving otherwise ex haust gases could be drawn into the passenger compartment If you must drive with the back door or rear win dow open follow these procedures 1 Open all the windows 2 Set the air flow control dial to the W position and turn the fan control dial to 4 high to circulate the air e If electrical wiring or other cable connections must pass to a trailer through the seal on the back door or body follow the trailer manufactur er s recommendation to prevent car bon monoxide entry into the vehicle e The exhaust system and body should be inspected by a qualified mechanic whenever a The vehicle is raised for service b You suspect that exhaust fumes are entering into the passenger compartment
240. not streak Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner Steering wheel Check for changes in the steering conditions such as excessive free play hard steering or strange noises Seats Check seat position controls such as seat adjusters seatback recliner etc to ensure they operate smoothly and all latches lock securely in every position Check that the head restraints move up and down smoothly and the locks if so equipped hold securely in all latched posi tions Seat belts Check that all parts of the seat belt system e g buckles anchors adjust ers and retractors operate properly and smoothly and are installed securely Check the belt webbing for cuts fraying wear or damage 8 4 Maintenance and do it yourself Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort Keep the floor mat away from the pedal Clutch pedal Make sure the pedal oper ates smoothly and check that is has the proper free travel Brakes Check that the brakes do not pull the vehicle to one side when applied Brake pedal and booster Check the pedal for smooth operation and make sure it has the proper distance under it when de pressed fully Check the brake booster func tion Be certain to keep the floor mat away from the pedal Parking brake Check that the
241. notice any leaks or if gasoline fumes are evident check for the cause and have it corrected immediately MAINTENANCE PRECAUTIONS When performing any inspection or mainte nance work on your vehicle always take care to prevent serious accidental injury to yourself or damage to the vehicle The following are general precautions which should be closely observed amp WARNING e Park the vehicle on a level surface apply the parking brake securely and block the wheels to prevent the ve hicle from moving Move the gear shift lever to P Park e Be sure the ignition key is in the OFF or Lock position when performing any parts replacement or repairs e Your vehicle is equipped with an automatic engine cooling fan It may come on at any time without warn ing even if the ignition key is in the OFF position and the engine is not running To avoid injury always dis connect the negative battery cable before working near the fan e lf you must work with the engine run ning keep your hands clothing hair and tools away from moving fans belts and any other moving parts Maintenance and do it yourself 8 5 It is advisable to secure or remove any loose clothing and remove any jewelry such as rings watches etc before working on your vehicle e Always wear eye protection when ever you work on your vehicle e If you must run the engine in an enclosed space such as a garage be sure there is proper ventilation for ex
242. ns to attach the tether strap to the tether strap anchor bracket Seats restraints and supplemental air bag systems 1 69 ROUTE tether strap through head restraint supports x To attach a tether strap to a second row bench or bucket seat 1 Route the tether strap under the head restraint and between the head restraint supports APD0839 e The head restraint on the second row bucket seat with the integrated child seat is not adjustable but there is an opening under the head restraint to route the tether strap through Gently lift the head restraint and route the tether strap under the center of the head restraint through to the back side of the seat 1 70 Seats restraints and supplemental air bag systems Second row bucket seat ARS1194 2 Hook the tether strap into the slot in the anchor bracket on the second row seat located on the lower back of the seat in line with the head restraint Second row bench seat Tether strap anchor brac kets ARS1193 Second row bench seat with integrated child safety seat Tether strap anchor bracket ARS1199 Second row child restraint placement Tether strap Tongue and buckle fastened ARS1192 3 Tighten the tether strap to remove any slack 4 Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure it is secu
243. ntrols should not be done while driving so full attention may be given to vehicle operation The Electronic Automatic Temperature Control EATC is located at the center of the instrument panel below the radio The EATC operates only when the ignition is turned to the ON position The EATC maintains the temperature you select and controls the airflow for your com fort It also allows you to override the auto matic operation with manual function selec tor buttons To turn the EATC on push either the AU TOMATIC button or any of the six function selector buttons ay GY Ww CW A or MAX To turn the EATC off press the OFF button When you select AUTOMATIC the system determines fan speed airflow location and discharge air temperature When one of the function selector buttons is pressed your selection determines airflow location only Fan speed and discharge air temperature remain automatic You can override fan speed by rotating the vertical thumbwheel amp located at the extreme right of the control panel The display window indicates the status of the system It shows the selected tempera ture and AUTO when in the AUTOMATIC mode It also indicates manual thumb wheel control of the fan speed when a amp is shown Heater air conditioner and audio systems 4 11 AUTOMATIC OPERATION Push the AUTOMATIC button and select the desired temperature The selected tempera ture and AUTO show in the display w
244. o each use If the belt is not locked repeat steps three through six After the child restraint is removed and the seat belt is fully retracted for the passenger side of the two passenger bench seat the auxilliary buckle must also be released the automatic locking mode child restraint mode is canceled Seats restraints and supplemental air bag systems 1 63 Move seat fully back INSTALLATION ON FRONT PASSENGER SEAT amp WARNING e Never install a rear facing child re straint in the front passenger seat Supplemental front air bags inflate with great force A rear facing child restraint could be struck by the air bag in a crash and could seriously injure or kill your child ARS1135 e NISSAN recommends that child re straints be installed in the rear seat However if you install a forward facing child restraint in the front pas senger seat move the passenger seat to the rear most position A child restraint with a top tether strap should not be used in the front passenger seat 1 64 Seats restraints and supplemental air bag systems e The three point belt in your vehicle is equipped with a locking mode re tractor which must be used when installing a child restraint Failure to use the retractor s locking mode will result in the child restraint not being properly secured The re straint could tip over or otherwise be unsecured and cause injury to the child in a sudden sto
245. o equipped 20 21 22 23 24 25 26 27 28 29 30 31 32 Cigarette lighter accessory Audio controls Ignition switch steering lock Driver supplemental air bag Tilt steering lock lever Parking brake Hood release lever Fuse box cover Cruise control main and set switch Front fog light switch Windshield wiper turn signal high beam switch Headlight control switch Instrument brightness control Instruments and controls 2 3 METERS AND GAUGES liy 30 80 4 60 20 40 riny E _ WICO149 2 4 Instruments and controls 1 Engine coolant temperature gauge 2 Tachometer 3 Speedometer 4 Fuel gauge 5 Reset button for trip odometer 6 Odometer trip odometer 7 Message center 8 Message center button WICO0078 SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour MPH and kilometers per hour km h Odometer Twin trip odometer The odometer twin trip odometer is dis played when the ignition key is in the ON position The odometer records the total distance the vehicle has been driven ni il Reset Lit ODO button PUSH WIC0084 The twin trip odometer records the distance of individual trips Changing the display Pushing the reset button changes the dis play as follows ODO TRIP A gt TRIP B ODO Resetting the trip odometer
246. of the paint to avoid lasting damage or staining Special cleaning prod ucts are available at an authorized NISSAN dealer or any automotive accessory store UNDERBODY In areas where road salt is used in winter the underbody must be cleaned regularly This prevents dirt and salt from building up and causing the acceleration of underbody and suspension corrosion GLASS Use glass cleaner to remove smoke and dust film from the glass surfaces It is nor mal for glass to become coated with a film after the vehicle is parked in the hot sun Glass cleaner and a soft cloth easily remove this film CAUTION When cleaning the inside of the win dows do not use sharp edged tools abrasive cleaners or chlorine based disinfectant cleaners They could dam age the electrical conductors radio an tenna elements or rear window defog ger elements ALUMINUM ALLOY WHEELS Wash regularly especially during winter months in areas where road salt is used Salt could discolor the wheel if not removed CHROME PARTS Clean all chrome parts regularly with a non abrasive chrome polish to maintain the finish CLEANING INTERIOR Occasionally remove loose dust from the interior trim plastic parts and seats using a vacuum cleaner or soft brush Wipe the vinyl and leather surfaces with a clean soft cloth dampened in mild soap solution then wipe clean with a dry soft cloth Before using any fabric protector read the manu facturer s re
247. on Press this button to activate the compres sion function This reduces the dynamic range which provides the listener with a more consistent level of volume The dis play window shows a C when the COMP button is pushed Clock operation The clock is on in the display regardless of what mode media or function the radio is in as long as the ignition is in ACC or ON Clock set Press the RDS CLK button until SELECT HOURS is displayed then use the SEL A Y buttons to change the hour press the RDS CLK button again until SELECT MINS is displayed then use the SEL A VY buttons to change the minutes The display will return to clock priority mode in 10 seconds or press the RDS CLK button to return to the clock display Selecting the desired band Push the AM or FM buttons to change to AM or FM band reception The FM stereo indicator ST illuminates during FM stereo reception When the stereo broad cast signal is weak the radio automatically changes from stereo to monaural reception FM AM radio operation MUTE button Push the MUTE button to mute out the radio TUNE buttons lt q gt A WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation Use the lt Q or gt buttons for manual tuning To move quickly through the chan nels hold either of the tune buttons down for more than 0 5 seconds AUTO SET Press the AUTO button while listening to the radio to activate t
248. on amp CAUTION It is important to replace the floor mats whenever they are removed for any reason The floor mats are intended to help prevent the possibility that high heeled shoes or similar objects might become stuck in the seat tracks Failure to replace the floor mats might result in personal injury Be sure to keep the seat tracks clear of debris by cleaning them periodically Review the following illustrations so you will know the proper way to place the floor mats with the various seating arrangements available in your vehicle Seats restraints and supplemental air bag systems 1 27 Front mats Front mats ARS1218 ARS1219 Five Passenger Seating 1 28 Seats restraints and supplemental air bag systems Floor mat positioning pin Cargo Rear mat mat Five Passenger Seating with cargo room The step mats are not used in this seating configuration ARS1220 Front mats Cargo Rear see mal mat niat positioning pin ARS1221 Three passenger bench seat in fully forward position The step mats are not used in this seating configuration Seats restraints and supplemental air bag systems 1 29 Floor mat positioning pin Floor mat Step mat ed Seat track APDO0083 Floor mat positioning aid Positioning pins are attached to three of the floor mats The cargo mat and front mats do not have pins However the driver s front floor mat h
249. onditioner cooling function op erates only when the engine is running HEATER OPERATION Heating This mode is used to direct most of the hot air to the front and rear floor outlets Rear passenger heat is provided by the front system through floor outlets located under both front seats 1 Move the air control dial to the po sition 2 Turn the fan control dial to select speed 3 Move the temperature control dial to the desired position 4 4 Heater air conditioner and audio systems Ventilation This mode directs air to the side and center vents 1 Move the air control dial to the po sition 2 Turn the fan control dial to select speed 3 Move the temperature control dial to the desired position Defrosting or defogging This mode is used to defrost defog the windows 1 Move the air control dial to the yy po sition 2 Turn the fan control dial to select speed 3 Move the temperature control dial to the desired position When the position is selected the air conditioner automatically turns on however the indicator light will not illu minate if the outside temperature is more than 45 F 7 C This dehumidifies the air which helps defog the windshield The air recirculation mode automatically turns off allowing outside air to be drawn into the passenger compartment which helps defog the windshield Bi level heating cooling The bi level mode directs air to the side and cen
250. ong periods of usage dirt can collect on the video heads causing the picture to become blurred or interrupted In this case head cleaning may be required To clean the video heads obtain a head cleaning tape from your local video store Be sure to completely follow the instructions included with the cleaning tape Excessive cleaning can shorten video head life Heater air conditioner and audio systems 4 43 TROUBLESHOOTING Use the following troubleshooting chart to remedy symptoms you may experience If the problem is not readily corrected consult your Nissan dealer for assistance SYMPTOM POSSIBLE CAUSE SOLUTION VCP is not plugged in Plug in VCP No power Vehicle ignition is ON power indi cator is OFF VCP does not operate Power indicator is flashing Blown fuse The VCP has condensation and the protection circuit is operating The temperature is too high and the protec tion circuit is operating Replace fuse Wait until the VCP becomes dry inside This may take several hours Wait until vehicle cabin temperature cools down Power indicator LED is off The fuse may be burned out Replace fuse The wiring is incomplete Check the wire connections and connect it prop erly The picture has shadows stripes or spots The screen is dark Tracking needs to be adjusted Adjust tracking Video tape is bad The brightness is adjusted too low Try another video tape Check
251. or cap when the engine is hot Serious burns could be caused by high pressure fluid escaping from the radiator The radiator is equipped with a pres sure cap To prevent engine damage use only a genuine NISSAN radiator cap Engine coolant reservoir cL range CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold If the coolant level is below MIN add coolant up to the MAX level If the reservoir tank is empty check the coolant level in the radiator when the engine is cold If there is insufficient cool ant in the radiator fill the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level If the cooling system frequently requires coolant have it checked by an autho rized NISSAN dealer CHANGING ENGINE COOLANT An authorized NISSAN dealer can change the engine coolant The service procedure is found in NISSAN s service manual Improper servicing can result in reduced heater performance and engine overheating A WARNING e To avoid danger of being scalded never change the coolant when the engine is hot e Never remove the radiator cap when the engine is hot Serious burns could be caused by high pressure fluid escaping from the radiator e Avoid direct skin contact with used coolant If skin contact is made wash thoroughly with soap or hand c
252. orce the compact disc into the slot This could damage the player TAPE CD When the CD side of the TAPE CD button is pushed with the compact disc loaded and the tape or the radio playing the tape or radio turns off and the compact disc starts to play FF Fast Forward REW Rewind When the FF or REW button is pushed while the compact disc is playing the com pact disc plays at an increased speed while fast forwarding or rewinding When the but ton is released the compact disc returns to normal play speed SEEK lt q or gt When the SEEK gt button is pushed while the compact disc is playing the next selection following the present one starts to play from the beginning Push the SEEK gt button sev eral times to skip several selections Each time the button is pushed the CD advances one additional selection The number appears in the display window When the last selec tion on the compact disc is skipped the first selection is played When the SEEK button is pushed the se lection being played returns to the beginning Push the SEEK 4d button several times to skip back several selections Each time the button is pushed the CD moves back one selection SHUFFLE When the SHUFFLE button is pressed the tracks on the CD are played at random not following the sequence on the compact disc The same program may be repeated twice CD EJECT When the EJ button is pushed with a com pact disc loaded the compact disc
253. orporation in Hawaii 2880 Kilihau St Honolulu Hawaii 96819 For Canadian customers Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle Table of Contents Seats restraints and supplemental air bag systems Instruments and controls Pre driving checks and adjustments Heater air conditioner and audio systems Starting and driving In case of emergency Appearance and care Maintenance and do it yourself Technical and consumer information 1 Seats restraints and supplemental air bag systems Front manual seat adjustment ee Front power seat adjustment if SO CQUIPPO eeeeceeeeseeeeeeeeeeeeeeeenteeneses Three passenger seat adjustment Head restraint adjustment ceeeeeee PAVING SS saines a aeae maniacs Underseat storage tray eeeeseeeeeeeeereeeeee Flexible S ating ccescceesseceeeeeeeseseeetesteeeeses Tabletop seats cccccceeeeeeeeeeeeeeeeteeeeeeeeeneeees Seats floor Mats eeceeeeeeeeeeeeeeeeeeeeeseeeeeneeeeeeee Seating arrangement cceeeeeeeeeeeeeeeees Seat positions 20 eeececeseeeeseeeeeeeeeeesseeseneeees Floor mat POSITIONS vescsecsceceseisscssccsipeee cavseeenecee Supplemental restraint SySteM ccceeeeee Precautions on supplemental restraint Syste oy sc5pcvers itis seas dence E Supplemental air bag warning labels
254. ose not to drive under the influence of alcohol Every year thou sands of people are injured or killed in alcohol related accidents Although the local laws vary on what is considered to be legally intoxicated the fact is alcohol affects all people differently and most people un derestimate the effects of alcohol Remember drinking and driving don t mix And that s true for drugs too over the counter prescription and illegal drugs Don t drive if your ability to operate your Starting and driving 5 3 vehicle is impaired by alcohol drugs or some other physical condition 5 4 Starting and driving IGNITION SWITCH WSD0002 The ignition switch includes an anti theft steering lock device The key can only be removed when the ignition switch is in the LOCK position The ignition lock is designed so the key cannot be turned to LOCK and removed until the shift lever is moved to the P Park position The shift lever is designed so it cannot be moved out of P Park and into any of the other gear positions if the ignition key is turned to LOCK or if the key is removed from the switch The shift lever can be moved out of P Park only after the ignition switch is in the ON position and the foot brake pedal is depressed To lock the steering wheel turn the key to the LOCK position Remove the key To unlock the steering wheel insert the key and turn it gently while rotating the
255. osition Photo sensor for autolamp AIC1087 Be sure you do not put anything on top of the photo sensor located in the top left side of the instrument panel The photo sensor controls the autolamp if it is covered the photo sensor reacts as if it is dark out and the headlights will illumi nate HAZARD WARNING FLASHER SWITCH Right turn Ta Left turn AIC0560 TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal the turning direction When the turn is com pleted the turn signal cancels automati cally Lane change signal To indicate a lane change move the lever up or down to the point where the light begins to flash but the lever does not latch AICO102 CORNERING LIGHT The cornering light provides additional illu mination toward the turning direction The light on the turning direction side comes on when a turn is signaled with the headlights on Push the A hazard switch to warn other drivers when you must stop or park under emergency conditions All turn signal lights flash Press the switch again to turn the hazard warning flashers off A WARNING e If stopping for an emergency be sure to move the vehicle well off the road Instruments and controls 2 19 e Do not use the hazard warning flash ers while moving on the highway unless unusual circumstances force you to drive so slowly that your ve hicle might become a ha
256. our warranty coverage If in doubt about any servicing have it done by an authorized NISSAN dealer ENGINE COMPARTMENT CHECK LOCATIONS Power steering fluid reservoir Engine oil dipstick Brake fluid reservoir Air cleaner housing Battery Fuse and relay box Radiator cap Fuse and relay box o ON Oa FW N Automatic transmission fluid dipstick 10 Engine oil filler cap 11 Spark plug wires 12 Windshield washer fluid reservoir 13 Engine coolant reservoir WDI0104 Maintenance and do it yourself 8 7 ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a high quality year round anti freeze coolant solution The anti freeze so lution contains rust and corrosion inhibitors therefore additional engine cooling system additives are not necessary A CAUTION When adding or replacing coolant be sure to use only a Genuine Nissan anti freeze coolant green or equiva lent with the proper mixture ratio of 50 anti freeze and 50 demineralized or distilled water The use of other types of coolant solutions or coolant colors such as orange may damage the engine cooling system Genuine Outside tempera NISSAN ture down to Demineral Anti freeze ized or Dis Coolant or tilled water equivalent 8 8 Maintenance and do it yourself A WARNING Never remove the radiat
257. ous selection on the CD In CD DJ mode the SEEK lt and gt buttons allow the rear passengers to find the next or previous selection on the CD 4 42 Heater air conditioner and audio systems Speaker control button With the speakers ON rear seat passen gers can adjust the audio output to all system speakers both front and rear to gether headphones are disabled in this mode The rear seat passengers cannot raise the volume of the system above the level of the front radio With the speakers OFF the headphones are enabled The rear seat passengers have control over the desired headphone volume levels Headphone jacks Two headphone jacks are available so two rear seat passengers may listen to the audio system Headphones are not included with the ve hicle Most portable radio headphones will work with the rear audio controls Auxiliary input jacks The auxiliary input jacks on the RSEM con trol panel accept video and audio connec tors for all standard video games Other compatible devices such as DVD players camcorders and portable CD players can also be connected to the auxiliary jacks The auxiliary jacks are color coded for iden tification purposes e Yellow video input e White left channel audio input e Red right channel audio input DUAL PLAY mode Dual Play Mode allows the rear seat pas sengers to listen to one media source while the front seat passengers listen to another To activate p
258. oved forward to allow easier entry and exit for third seat passen gers Seats restraints and supplemental air bag systems 1 17 Cupholders built into tabletop seats ARS1138 TABLETOP SEATS The second and third row seats convert into tabletops with built in cupholders To use the tabletop seats lift up on the seatback release lever and fold the seatback forward A WARNING e Never place hard items such as cof fee mugs or drinking glasses on the tabletop seats when the vehicle is moving Any item can become a pro jectile inside a vehicle involved in a collision To help prevent personal injury never leave loose items on the folded down tabletop seats when the vehicle is moving Do not use the tabletop and cup holder feature while the vehicle is in motion unless you are properly seated with your seat belt on 1 18 Seats restraints and supplemental air bag systems SEATS FLOOR MATS Seatback will fold down and the seat will move forward automatically PUSH the seat rear ward until it securely locks in position LIFT lever to fold seatback and move seat forward There is also a lever behind the passenger bucket seat that allows third seat passen gers to move the bucket seat forward with out help from another passenger SEATING ARRANGEMENTS FUSE Ine sear Many different arrangements for passenger back until it seating or cargo hauling are available as securely locks
259. p or collision Move seat fully back ARS1163 If you must install a child restraint in the front seat follow these steps 1 Position the child restraint on the front passenger seat It should be placed in a forward facing direction only Move the seat to the rearmost position Always follow the child restraint manufacturer s instructions Child restraints for infants must be used in the rear facing direc tion and therefore must not be used in the front seat Front facing se eer ARS1164 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing Front facing PULL to engage automatic locking mode ARS1165 3 Pull on the shoulder belt until all of the belt is fully extended At this time the seat belt retractor is in the automatic locking mode child restraint mode It reverts back to emergency locking mode when the seat belt is fully retracted Seats restraints and supplemental air bag systems 1 65 Front facing PULL to tighten S ARS1166 4 Allow the seat belt to retract Pull up on the belt to remove any slack in the belt Front facing Check for a secure fit ARS1167 5 Before placing the child in the child re straint use force to tilt the child restra
260. peratures can lead to sudden tire failure Grade C corresponds to a performance level which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades A and B represent higher levels of perfor mance on laboratory test wheels than the minimum required by law Technical and consumer information 9 19 A WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed under inflation or excessive loading either separately or in combi nation can cause heat build up and possible tire failure EMISSION CONTROL SYSTEM WARRANTY Your NISSAN is covered by the following emission warranties For US 1 Emission Defects Warranty 2 Emission Performance Warranty Details of these warranties may be found with other vehicle warranties in your War ranty Information Booklet that comes with your NISSAN If you did not receive a Warranty Information Booklet or it has be come lost you may obtain a replacement by writing to e Nissan North America Inc Consumer Affairs Department P O Box 191 Gardena CA 90248 0191 For Canada Emission Control System Warranty Details of these warranties may be found with other vehicle warranties in your War ranty Information Booklet that comes with your NISSAN If you did not receive a Warranty Information Booklet or it has be come lost you may obtain a replacement by writing to 9 20 T
261. played Fuel economy is displayed in liters 100 km or miles gallon Your vehicle must be moving to calculate fuel economy Fuel economy is averaged from the last reset To reset hold down the reset button momentarily Distance to empty This will display how many kilometers or miles you can drive until you run out of fuel To ensure accuracy turn the ignition off when you fill the fuel tank Instruments and controls 2 7 WARNING INDICATOR LIGHTS AND AUDIBLE REMINDERS F Par naati O D Overdrive off indicator light a 5 Turn signal hazard indicator lights Ee Charge warning light OFF automatic transmission only BRAKE O Brake warning light PN Low fuel warning light EENE Malfunction indicator lamp MIL High beam indicator light ew Low washer fluid warning light ss Anti lock brake warning light iA Seat belt WARNING light and chime CRUISE CRUISE main switch indicator light A Supplemental air bag warning light Q57 Engine oil pressure warning light SET Cruise SET switch indicator light Aah Door open warning light CHECKING BULBS With all doors closed apply the parking brake fasten seat belts and turn the ignition key to the ON position without starting the engine The following lights come on and stay on until the engine is started BRAKE SERVICE E O ty Bar The following lights come on briefly
262. posal procedures are set forth in the appropriate NISSAN Service Manual Incorrect disposal procedures could cause personal injury SEAT BELTS PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured or killed in an accident and or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted NISSAN strongly encourages you and all of your passengers to buckle up every time you drive even if your seating position includes a supplemental air bag Most U S States and Canadian prov inces or territories require that seat belts be worn at all times when a vehicle is being driven Sit upright and well back A WARNING e Every person who drives or rides in this vehicle should use a seat belt at all times Children should be prop erly restrained and if appropriate in a child restraint e The belt should be adjusted to a snug fit Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident Seri ous injury or death can occur if the seat belt is not worn properly e Always route the shoulder belt over your shoulder and across your chest Never run the belt behind your back under your arm or across your neck The belt should be away from your face and neck but not falling off your shoulder e Position the lap belt as low and snug as possible AROUND THE HIPS NOT THE WAIST A lap
263. press the accelerator pedal while shifting from P Park or N Neutral to R Reverse D Drive 2 or 1 Always depress the brake pedal until shifting is completed Failure to do so could cause you to lose control and have an accident e Cold engine idle speed is high so use caution when shifting into a for ward or reverse gear before the en gine has warmed up e Never shift to P Park or R Reverse while the vehicle is moving This could cause an accident CAUTION e When stopping the vehicle on an uphill grade do not hold the vehicle by depressing the accelerator pedal The foot brakes should be used for this purpose e Do not downshift abruptly on slip pery roads This may cause a loss of control The automatic transmission in your vehicle is electronically controlled by a transmission control module to produce maximum power and smooth operation Shown on the following pages are the rec ommended operating procedures for this transmission Follow these procedures for maximum vehicle performance and driving enjoyment Starting the vehicle e After starting the engine fully depress the brake pedal before shifting the selector lever to the R Reverse N Neutral D Drive 2 or 1 position Be sure the vehicle is at a complete stop before at tempting to shift the selector lever This automatic transmission is designed so the brake pedal MUST be depressed before shifting from P Park to any other pos
264. ps 1 Position the child restraint on the seat Always follow the restraint manufactur er s instructions Rear facing INSERT to fasten ARS1182 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing 1 62 Seats restraints and supplemental air bag systems Rear facing PULL to engage automatic locking mode 3 Pull on the shoulder belt until all of the belt is fully extended At this time the seat belt retractor is in the automatic locking mode child restraint mode It reverts back to emergency locking mode when the seat belt is fully retracted Rear facing PULL to tighten ARS1184 4 Allow the seat belt to retract Pull up on the shoulder belt to remove any slack in the belt 5 Before placing the child in the child re Rear facing Check for a secure fit ARS1185 straint use force to tilt the child restraint from side to side and tug it forward to make sure it is securely held in place Check that the retractor is in the auto matic locking mode by trying to pull more seat belt out of the retractor If you can not pull any more belt webbing out of the retractor the seat belt is in the automatic locking mode Check to make sure the child restraint is properly secured prior t
265. quire that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper ated The optional second row bench seat con tains two integrated child safety seats These seats are designed for use only by children who weigh between 22 and 60 pounds 10 27 kg and whose height is 45 inches 1145 mm or less and who are capable of sitting upright alone Seats restraints and supplemental air bag systems 1 73 In addition these integrated child safety seats must only be used by children who meet the following requirements e AGE At least one year old e SEATED HEIGHT Top of child s shoulders must be below the shoulder harness openings of the integrated child seat Children less than one year old should be restrained in an appropriate separate child restraint Children whose shoulders are above the shoulder harness openings of integrated child seat should also be re strained in an appropriate separate child restraint or in the appropriate vehicle seat belt system Refer to Child Restraints and Precautions On Seat Belt Usage in this section for important child safety information Integrated child safety seat label locations Shoulder harness Seatback release lever Seat cushion ARS1215 Using the Integrated Child Safety Seats amp WARNING e Never use the vehicle seat belts to restrain a child in an integrated 1 74 Seats restraint
266. r glass open This could allow dangerous ex haust gases to be drawn into the ve hicle See Exhaust gas in the Start ing and driving section of this manual 3 10 Pre driving checks and adjustments To lock the rear door with the key turn the key clockwise as shown in the illustration Turning the key fully clockwise unlocks the rear window on models equipped with the flip up rear window The rear wiper auto matically lowers when the key is turned fully clockwise Do not force the wiper to lower by hand To close the rear window firmly push on the window until it locks in place The rear wiper automatically returns to the original position OPENER OPERATION To open the fuel filler lid grasp the right hand edge of the lid and pull FUEL FILLER CAP The fuel filler cap is a ratcheting type Tighten the cap clockwise until ratcheting clicks are heard Ensure the plastic tether doesn t get caught between the fuel filler cap and the fuel filler neck The driver side sliding door cannot be fully opened when the fuel door is open Make sure the driver side sliding door is completely closed before opening the fuel door A WARNING e Gasoline is extremely flammable and highly explosive under certain con ditions You could be burned or se riously injured if it is misused or mishandled Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling e Fuel m
267. r in this section Rear gt INSERT to ARS1161 Fastening the seat belts 1 Adjust the seat 2 Slowly pull the seat belt out of the retrac tor and insert the tongue into the buckle until you hear and feel the latch engage The retractor is designed to lock during a sudden stop or on impact A slow pulling motion permits the seat belt to move and allows you some freedom of movement in the seat Rear POSITION low on the hips ARS1162 3 Position the lap belt portion low and snug on the hips as shown 4 Pull the shoulder belt portion toward the retractor to take up extra slack The front seat passenger seat belt and rear three point seat belts have a cinching mechanism for child restraint installation It is referred to as the automatic locking mode When the automatic locking mode is acti vated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted Refer to Child restraints later in this section for more information The automatic locking mode should be used only for child restraint installation During normal seat belt use by a passen ger the locking mode should not be activated If it is activated it may cause uncomfortable seat belt tension Seats restraints and supplemental air bag systems 1 43 PRESS to unfasten ARS 1054 Unfastening the seat belts To unfasten the seat belt pres
268. r other than the specified quality or oil and filter change intervals longer than recommended could reduce engine life Damage to the engine caused by improper maintenance or use of incorrect oil and filter quality and or viscosity is not covered by the new NISSAN vehicle warranties Your engine was filled with a high quality engine oil when it was built You do not have to change the oil before the first recom mended change interval Oil and filter change intervals depend upon how you use your vehicle Operation under the following conditions may require more frequent oil and filter changes repeated short distance driving at cold outside temperatures driving in dusty conditions extensive idling towing a trailer Technical and consumer information 9 5 RECOMMENDED SAE VISCOSITY NUMBER Outside Temperature Range Anticipated Before Next Oil Change GASOLINE ENGINE OIL PREFERRED TI1028 e SAE 5W 30 viscosity oil is preferred for all temperatures SAE 10W 30 or 10W 40 viscosity oil may be used if 9 6 Technical and consumer information the ambient temperature is above 0 F 18 C AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The air conditioning system in this NISSAN vehicle must be charged with the refrigerant HFC 134a R 134a and the lubricant NISSAN type PAG F or the exact equivalents amp CAUTION Use of any other refrigerant or lu
269. r seat controls are on push the SPKRS ON OFF button to turn all speakers off Push again to turn all speakers on For vehicles equipped with the premium FM AM radio with cassette player compact disc player and 6 disc CD player when the rear seat controls are on push the SPKRS ON OFF button to turn the rear speakers off Push again to turn the rear speakers on 4 36 Heater air conditioner and audio systems If the rear audio system was on when the ignition was turned OFF the audio system remembers and the rear system is still on when the engine is started again The sys tem also remembers if the speakers were ON or OFF Therefore the speakers may have to be turned on again by pressing the SPKRS ON OFF button or turning the rear audio controls off ANTENNA The manual antenna on your vehicle re mains in the up position at all times The antenna cannot be shortened but can be removed When you need to remove the antenna turn the antenna rod counterclock wise To install the antenna rod turn the antenna clockwise Tighten the antenna rod to speci fication using a suitable tool such as a open end wrench The antenna rod tighten ing specification is 3 4 3 6 N m 30 32 in lb Do not use pliers to tighten the an tenna as they can leave marks on the an tenna surface The antenna rod cannot be hand tightened to the proper specification CAUTION Always properly tighten the antenna rod during install
270. r slots to tow another vehicle as this may cause body damage VEHICLE RECOVERY Freeing a stuck vehicle Tow chains or cables must only be at tached to the main structual members of the vehicle Pulling devices should be routed so they do not touch any part of the suspension steering brake or cooling systems Always pull the cable straight out from the front or rear of the vehicle Never pull the vehicle at an angle e Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery e Stand clear of a stuck vehicle WARNING Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be damaged 7 Appearance and care Cleaning exterior int 7 2 Floor MAtS er e e dani Ai 7 4 WaS NING ierse eranstearen iste eaaa ra as iE 7 2 Seat DEMS iienaa E EEE SEES 7 4 WAXING oSer aa aaee aR 7 2 Corrosion protection cccccccsscssseesseecseesteeeseeeeees 7 4 REMOVING SPOtS c cccceeeeeeeeeeeeeeeeeeeeeeeeeteneaes 7 3 Most common factors contributing to Underbody ceeceeeeeeeeeeeeeeeneeseeeeeeeeeneeeeeeeeeeeas 7 3 vehicle COFFOSION cccccesecesseceteecseeeceeeteeesseeees 7 4 Gla os a ot EE E ET 7 3 Environmental factors influence the rate Aluminum alloy wheels ccscesseseeeeeeees 7 3 Of COMOSION seca t2ece cas ceczacecsavstz ca massviaacasticetinratiiees 7 4 Chrome parts
271. ral single channel FM having slightly more range than stereo FM External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles 40 km The strength of the FM signal is directly related to the distance between the transmitter and receiver FM signals follow a line of sight path exhibiting many of the same characteristics as light For example they will reflect off objects Fade and drift As your vehicle moves away from a station transmitter the signals will tend to fade and or drift Static and flutter During signal interference from buildings large hills or due to antenna 4 16 Heater air conditioner and audio systems position usually in conjunction with in creased distance from the station transmit ter static or flutter can be heard This can be reduced by adjusting the treble control counterclockwise to reduce treble re sponse Multipath reception Because of the reflec tive characteristics of FM signals direct and reflected signals reach the receiver at the same time The signals may cancel each other resulting in momentary flutter or loss of sound AM RADIO RECEPTION AM signals because of their low frequency can bend around objects and skip along the ground In addition the signals can be bounced off the ionosphere and bent back to earth Because of these characteristics AM signals are also subject to interference as they travel from transmitter to recei
272. rely held in place 5 Check to make sure the child restraint is properly secured prior to each use If not secure repeat steps two through four Seats restraints and supplemental air bag systems 1 71 INSTALLATION ON THREE PASSENGER BENCH SEAT IN SECOND ROW A child restraint with a top tether strap may be placed at the passenger side outboard and center positions on the three passenger bench seat when the seat is in the second row location Once the child restraint is prop erly secured to the seat see Installation on second and third row outboard positions Front facing earlier in this section follow the directions explained in Installation on three passenger bench seat in third row later in this section INSTALLATION ON THREE PASSENGER BENCH SEAT IN THIRD ROW A child restraint with a top tether strap may be placed at the passenger driver side out board and center positions on the three passenger bench seat when the seat is in the third row location Once the child re straint is properly secured to the seat see Installation on second and third row out board positions Front facing or Installation on three passenger bench seat center posi tion Front facing earlier in this section follow the directions to attach the tether strap anchor brackets 1 72 Seats restraints and supplemental air bag systems Passenger outboard seating position shown ROUTE tether strap through hea
273. repair it if necessary The automatic transmission is equipped with an electronic Fail Safe mode This sys tem allows the vehicle to be driven even in the event of damage to the electrical cir cuits If this occurs the transmission may default to third gear in drive range NOTE See Fail safe in the Starting and driving section of this manual before visit ing an authorized NISSAN dealer Turn signal hazard indicator eo lights The appropriate light flashes when the turn signal lever is activated Both lights flash when the hazard switch is turned on gt High beam indicator light Blue This light comes on when the headlight high beam is on and goes out when the low beam is selected cruise Cruise main switch indicator light The light comes on when the cruise control main switch is pushed The light goes out when the main switch is pushed again While the cruise main switch indicator light comes on the cruise control system is operational SET Cruise set switch indicator light The light comes on while the vehicle speed is controlled by the cruise control system If the light blinks while the engine is running it may indicate the cruise control system is not functioning properly Have the system checked by your NISSAN dealer SKE Malfunction indicator lamp soon MIL If this indicator lamp comes on steady or blinks while
274. ress the speaker control but ton and plug a headphone into the head phone jack With the headphones ON the rear speaker will not operate Select the desired media and adjust as necessary Press the speaker control button again to operate the rear speakers and disengage Dual Play Mode IN HOME use Your Autovision Family Entertainment System is UL registered for in home use To use the FES system in your home you will need e 12V DC power converter rated for 1 5 amps minute e Patch cords with RCA style connectors CARE AND MAINTENANCE Use a lightly dampened lint free cloth to clean the surfaces of your Family Entertain ment System VCP face monitor screen remote control etc CAUTION e Do not use any solvents or cleaning solutions when cleaning the video system e Do not use excessive force on the monitor screen e Avoid touching or scratching the monitor screen as it may become dirty or damaged Your Family Entertainment System is com patible with any cassette tape bearing the VHS mark We recommend storing your video cassettes in a moisture free dust free container CAUTION e Do not attempt to operate the system in extreme temperature conditions below 30 and above 113 Fahren heit e Do not attempt to operate the system in extreme humidity conditions less than 10 or more than 75 Tape head cleaning Normally the VCP will not require frequent head cleaning However after l
275. rning light cee 1 37 Hazard warning flasher switch 2 19 Vehicle security system 2 12 Warning labels for SRS seee 1 37 Warning indicator lights and audible FOMING SIS siisii nesenie 2 8 Weights See dimensions and weights 9 9 Wheels and tires 0 0 eee eee 8 31 9 9 Wheel tire size 0 0 ec sceeesscesseeseseeneeeseeneonee 9 9 When traveling or registering your vehicle in another country ww 9 10 Window washer fluid eee 8 14 Windows Locking passengers windows 2 31 Manual vent windows cee 2 32 Power vent WiINdOWS cece 2 32 Power WINKOWS viaccisteecssccsecvecsenteceecerseees 2 30 Windshield wiper and washer switch 2 15 Wiper Rear window wiper and washer SWILCHOS innsir 2 16 Windshield wiper and washer switch 2 15 Wiper blades 8 19 GAS STATION INFORMATION QUICK REFERENCE Recommended fuel Unleaded gasoline at least 87 AKI number RON 91 Engine oil 8 9 i Le Engine coolant 8 8 or further details such as gasohol see Hood wins washer fluid 8 14 Fuel recommendation in the Technical release and consumer information section 3 9 R i il ee engine oil Meters Audio system 4 16 4 21 4 27 e Certification Mark and a Air conditioner 4 3 4 11 e API SG SH Energy Conserving amp Il or gauges ae a API grade SJ Energy Conserving 2 4 f e ILSAC grade GF I amp GF II Driver supplemental e 5W 30 viscosity preferred a
276. rror information see Memory driver seat and mirrors later in this section 1 Push the a button on the keyfob Only the driver door unlocks Parking lights flash once 2 The interior lights come on and stay on for 30 seconds 3 Push the a button on the keyfob again within five seconds The passenger door sliding doors and the rear door unlock The interior lights can be turned off without waiting 30 seconds by either turning the ignition to ON or locking the doors with the multi remote controller Using the panic alarm If you are near your vehicle and feel threat ened you may activate the panic alarm to call attention as follows 1 Push and hold the m button on the keyfob for at least one full second 2 The theft warning alarm horn sounds and the headlights and tail lights flash for 30 seconds The panic alarm stops when it has run for 30 seconds or the go the a button is pressed or the e e Q pm button is released and re pushed PRESS and hold buttons for two seconds AIC1037 Silencing the horn beep feature If desired the horn beep feature can be deactivated using the keyfob The instruc tions are on the back of the keyfob To deactivate Press and hold the and a buttons for at least two seconds The hazard lights will flash three times to confirm that the horn beep feature has been deactivated To activate Press and hold the and a buttons for at least
277. rt the engine AVOIDING COLLISION AND ROLLOVER A WARNING Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident Be alert and drive defensively at all times Obey all traffic regulations Avoid excessive speed high speed cornering or sudden steering maneuvers because these driving practices could cause you to lose control of your vehicle As with any vehicle loss of control could result in a collision with other vehicles or objects or cause the vehicle to roll over particularly if the loss of control causes the vehicle to slide sideways Be attentive at all times and avoid driving when tired Never drive when under the influence of alcohol or drugs including prescription or over the counter drugs which may cause drowsi ness Always wear your seat belt as out lined in the Seats restraints and supplemental air bag systems section of this manual and also instruct your passen gers to do so DRINKING ALCOHOL DRUGS AND DRIVING A WARNING Never drive under the influence of alco hol or drugs Alcohol in the blood stream reduces coordination delays reaction time and impairs judgement Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others Additionally if you are injured in an accident alcohol can increase the se verity of the injury NISSAN is committed to safe driving How ever you must cho
278. s and supplemental air bag systems child safety seat Use only the shoul der harness and belt buckle which is part of the integrated child safety seat Never use the integrated child safety seat as a booster cushion with the vehicle seat belts e Before placing the child in the inte grated child safety seat confirm that the bench seatback is securely locked and the seatback release le ver is in full down position Always make sure the integrated child safety seat belts are properly positioned on your child The child should sit straight up and back against the bench seat The shoulder harnesses should be centered over the shoulders and fastened with the chest clip The belt buckle should be between the legs and latched to the shoulder belt tongue Snugly adjust the belts around your child Failure to properly position the child can increase the risk or severity of injury to the child in an accident CAUTION Securing the child Before using the integrated child safety seats carefully read the shoulder har ness seatback release and integrated child safety seat cushion labels The following steps apply to both the left and right integrated child safety seats 1 Be sure your child meets all of the re quired age weight and height require ments for the safe use of the integrated child safety seat 2 Be sure the second row bench seat is securely latched to the floor of the ve hicle Refer to Flexible sea
279. s must be adjusted before programming position 1 or position 2 Programming a keyfob 1 Move the driver seat and outside mirrors by pressing the desired position 1 or position 2 button 2 Press and hold the same position 1 or position 2 button 3 Within 10 seconds press the a button on the keyfob The keyfob is now programmed for that position 1 or position 2 button After the keyfob has been programmed the memory seat and mirror button indicator light will flash to indicate the keyfob is programmed If the memory seat button is pressed and held the indicator light will remain illuminated for as long as the button is held or 10 seconds which ever is shorter To remove a keyfob from the memory seat system press and hold both memory seat and mirror position buttons 1 and 2 and then press the button on the keyfob PD1006M INSIDE MIRROR The night position reduces glare from the headlights of vehicles behind you at night amp WARNING Use the night position only when nec essary because it reduces rear view clarity Pre driving checks and adjustments 3 13 rs UP Left mirror Right mirror position position Gi AS Y da LEFT lt RIGHT DOWN APD1052 OUTSIDE MIRRORS The outside mirrors operate only when the ignition switch is in the ACC or ON position Move the switch to select the right or left side mirror then adjust using the control lever amp WARNING
280. s sities meec acter 3 12 MINOS nce cosets Pant noni een meena 3 12 Memory driver seat and mirrors if SO CQUIPPOU 0 c 0 cceccecnesecerescteeeserereseeees 3 12 Inside MINOT siana 3 13 Outside MINOrS sdentato 3 14 KEYS es j D M Master key X1234 Key number plate Keyfob A key number plate is supplied with your key Record the key number and keep itin a safe place such as your wallet NOT IN THE CAR NISSAN does not record key numbers so it is very important to keep track of your key number plate A key number is necessary only when you have lost all vehicle keys and do not have one to duplicate If you still have a key this key can be duplicated by an authorized NISSAN dealer or locksmith shop WPDO0088 3 2 Pre driving checks and adjustments Two keys are supplied with your vehicle one has a plastic head and one is all metal Both keys perform the same functions DOORS A WARNING e Always have the doors locked while driving Along with the use of seat belts this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle This also helps keep children and others from unintention ally opening the doors and will help keep out intruders e Before opening any door always look for and avoid oncoming traffic e Do not leave children unattended in side the vehicle They could unknow ingly activate switch
281. s such as washing mitts Care must be taken when removing caked on dirt or other foreign sub stances so that the paint surface is not scratched or damaged Rinse the vehicle thoroughly with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt There fore these areas must be regularly cleaned Take care that the drain holes in the lower edge of the door are open Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt A damp chamois can be used to dry the vehicle to avoid water spots WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance After waxing polishing is recommended to remove built up residue and to avoid a weathered appearance An authorized NISSAN dealer can assist you in choosing the proper product e Wax your vehicle only after a thorough washing Follow the instructions supplied with the wax e Do not use a wax containing any abra sives cutting compounds or cleaners that may damage the vehicle finish e If the surface does not polish easily use a road tar remover and wax again Machine compounding or aggressive pol ishing on a base coat clear coat paint finish may dull the finish or leave swirl marks REMOVING SPOTS Remove tar and oil spots industrial dust insects and tree sap as quickly as possible from the surface
282. s the button on the buckle The seat belt automatically retracts Checking seat belt operation Seat belt retractors are designed to lock seat belt movement 1 when the seat belt is pulled quickly from the retractor and 2 when the vehicle slows down rapidly To increase your confidence in the seat belts check their operation as follows e Grasp the shoulder belt and pull quickly forward The retractor should lock and restrict further belt movement If the retractor does not lock during this check or if you have any questions about belt operation see an authorized NISSAN dealer 1 44 Seats restraints and supplemental air bag systems Shoulder belt height adjustment for front seats The shoulder belt anchor height should be adjusted to the position best for you See Precautions on seat belt usage earlier in this section To adjust press the release button and move the shoulder belt anchor to the desired position so the belt passes over the center of the shoulder The belt should be away from your face and neck but not falling off your shoulder Release the button to lock the shoulder belt anchor into position A WARNING e After adjustment release the adjust ment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position e The shoulder belt anchor height should be adjusted to the position best for you Failure to do so may reduce the effecti
283. sal Transceiver so that you can still see the red indicator light 2 36 Instruments and controls 5 Press the desired button until the red indicator light flashes slowly Do not re lease the button Continue holding and press the hand held transmitter button through step 6 6 Hold down both buttons until the red indicator light on the HomeLink Univer sal Transceiver flashes rapidly This may take 1 to 90 seconds Then release both buttons The rapid flashing means that the transceiver has been successfully programmed to match your hand held transmitter You can now use the HomeLink Universal Transceiver in stead of your hand held transmitter PROGRAMMING Homelink FOR CANADIAN CUSTOMERS Prior to 1992 D O C regulations required many hand held transmitters to stop trans mitting after one or two seconds even though you continue to hold down the but ton If you think you have one of these hand held transmitters you should press and re press the transmitter button every 2 seconds without ever releasing the HomeLink Universal Transceiver button The indicator light on the HomeLink Uni versal Transceiver should blink rapidly indi cating a successful programming proce dure If it returns to the slow blink of program mode continue to periodically reactivate your hand held transmitter until a success ful programming procedure is indicated by the rapidly flashing indicator light OPERATING THE HomeLink UNIVER
284. sh the SCAN tuning button SCAN illumi nates in the display SCAN tuning begins from low to high frequencies and stops at each broadcasting station for 5 seconds Pushing the button again during this 5 sec ond period stops SCAN tuning and remains tuned to that station 4 22 Heater air conditioner and audio systems SELECT STATION SEEK SCAN Manual FM1 ST T aw select 83 3 1 00 select E S une p MEMORIZE 59 3 J200 MaA Push and hold button CONFIRM appear when 89 3 72 00 memorizing SAVED is complete AHA1107 Saved will Station memory operations Six stations can be set for the AM band Twelve stations can be set for the FM band six for FM1 six for FM2 1 Push the FM or AM buttons to select AM FM1 or FM2 The selected band illumi nates in the display 2 Tune to the desired station 3 Push the desired station select button for more than 1 5 seconds The radio mutes when the select button is pushed 4 When the sound resumes memorizing is complete 5 Other station select buttons can be set in the same manner If the battery is disconnected or if the radio fuse opens the radio memory is canceled In that case reset the desired stations RDS Radio Data System RDS stands for Radio Data System and is a data information service transmitted by some radio stations on the FM band not AM band encoded withi
285. sinne 8 25 Interior lights 2 34 Light bulbs sss 8 25 Luggage compartment lights we 2 34 Spotlights See map light a se 2 35 Warning indicator lights and audible Ieelnallale Ee E E 2 8 Lock Child safety sliding door lock s 3 5 Door lOCKS siiin iisip 3 2 Fuel filler lid lock opener lever 3 10 Power door locks Rear door lock Luggage compartment lights 0 00 2 34 LUGGAGE TACK ie oiscsitssscssacsesteascesseteadsersosneceen 2 30 Luggage See vehicle loading information sirrini 9 13 10 3 M Maintenance General maintenance c 8 2 8 3 Maintenance precautions c ee 8 5 Seat belt maintenance 1 54 Under the hood and vehicle 8 4 Malfunction indicator lamp MIL seld Manual front seat adjustment sa 153 Manual vent Windows ceeeeeeeeeees 2 32 Map NIGMS cscseniseedsessssteisseisesssseaderasscseusensats 2 35 Map pockot raa 2 24 Mirror Outside MINOS craning 3 14 Vanity M FTOT wciescccssceesevsscccsecestsevsizeccenass 3 12 Multi remote control system See remote keyless entry SySteM cceesesesecseseeees 3 6 o OJOMElO Po reeur eE ENEN 2 5 Oil Capacities and recommended fuel UDHCAM S iii iipsissiniirissnscssrsiinsepus assar Changing engine Oil cece eeeeeeeee Changing engine oil filter Checking engine oil level Pe Engine Ola siestiact cee anann Engine oil and oil filter recommendation
286. size e Pixels e Screen resolution e Power source voltage e Power consumption e Operation temperature Color TFT active matrix LCD 6 4 Actual panel size 320X 234 224 640 dots DC 11 15V 0 8 Max 0 8A or less 30 F 113 F NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules NOTE This equipment may experience radio frequency interference from cellular phone two way and CB radio Heater air conditioner and audio systems 4 45 CAR PHONE OR CB RADIO Microphone installed model If equipped with a genuine NISSAN cellular phone your NISSAN features a non directional microphone in the steering col umn cover so it is not necessary to look at or speak directly into the microphone when calling To do so could detract from the driving Operation and cause an accident See the manual for car phone operation Pre wired and antenna for phone installed model Some models are pre wired to accept the genuine NISSAN cellular phone In addition the same model has the phone antenna built into the rear glass window When installing a CB ham radio a car phone or other transmitters in your NISSAN be sure to observe the following cautions otherwise the new equipment may ad versely affect the MFI Multiport Fuel Injec tion system and other electronic parts A WARNING e A cellular telephone should not be used w
287. spection in structions and replacement recom mendations The child restraints should be replaced if they are dam aged CHILD SAFETY Children need adults to help protect them They need to be properly restrained The proper restraint depends on the child s size Generally infants up to about 1 year and less than 20 pounds 9 kg should be placed in rear facing child restraints Forward facing child re straints are available for children who outgrow rear facing child restraints A WARNING Infants and children need special pro tection The vehicle s seat belts may not fit them properly The shoulder belt may come too close to the face or neck The lap belt may not fit over their small hip bones In an accident an improp erly fitting seat belt could cause seri ous or fatal injury Always use appro priate child restraints All US States and Canadian provinces re quire the use of approved child restraints for infants and small children See Child re straints later in this section In addition there are many types of child restraints available for larger children which should be used for maximum protection NISSAN recommends that all pre teens and children be restrained in the rear seat if possible According to accident statistics children are safer when prop erly restrained in the rear seat than in the front seat This is especially important because your vehicle has a supplemental restraint sys te
288. t belts 1 Insert the tongue into the buckle until you hear and feel the latch engage 1 52 Seats restraints and supplemental air bag systems 2 Tighten the seat belt by pulling the free end of the belt away from the tongue POSITION low on the gt hips ARS1076 3 Position the lap belt low and snug on the hips as shown ARS1057 4 Loosen the seat belt by holding the tongue at a right angle to the belt then pull on the belt PRESS to ARS1058 Unfastening the seat belts To unfasten the belt press the button on the buckle SEAT BELT EXTENDERS If because of body size or driving position it is not possible to properly fit the front seat lap belts and fasten them an extender is available which is compatible with the in stalled seat belts The extender adds ap proximately 8 inches 200 mm of length and may be used for either the driver or front passenger seating position See an autho Seats restraints and supplemental air bag systems 1 53 rized NISSAN dealer for assistance if the extender is required amp WARNING e Only NISSAN seat belt extenders made by the same company which made the original equipment belts should be used with NISSAN seat belts Persons who can use the standard seat belt should not use an extender Such unnecessary use could result in serious personal injury in the event of an accident SEAT BELT MAINTENANCE
289. tached to or affect the operation of the impact absorbing bumper Technical and consumer information 9 15 e Do not modify the vehicle exhaust system brake system etc to install a trailer hitch e To reduce the possibility of addi tional damage if your vehicle is struck from the rear where practical remove the hitch and or receiver when not in use e After the hitch is removed seal the bolt holes to prevent exhaust fumes waiter or dust from entering the pas senger compartment e Regularly check that all hitch mount ing bolts are securely mounted Tire pressures e When towing a trailer inflate the vehicle tires to the recommended cold tire pres sure indicated on the tire placard located on the inside of the glove box lid e Trailer tire condition size load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer s specifications 9 16 Technical and consumer information Safety chains Always use suitable safety chains between your vehicle and the trailer Safety chains should be crossed and should be attached to the hitch not to the vehicle bumper or axle Be sure to leave enough slack in the chains to permit turning corners Trailer lights Trailer lights should comply with Federal and or local regulations When wiring the vehicle for towing connect the stop and tail light pickup into the vehicle electrical circuit Class Trailer Tow electrical wiri
290. tch Sun shade Open and close the sun shade by sliding it forward or backward The shade opens when the sunroof opens but it must be closed manually A WARNING e In an accident you could be thrown from the vehicle through an open sunroof Always use seat belts and child restraints e Do not allow anyone to stand up or extend any portion of their body out of the sunroof opening while the vehicle is in motion or while the sunroof is closing CAUTION e Remove water drops snow ice or sand from the sunroof before opening e Do not place any heavy object on the sunroof or surrounding area Instruments and controls 2 33 INTERIOR LIGHTS AICO053 The interior lights operate regardless of ignition key position One interior light is located overhead near the front seats and one is overhead near the rear seat The interior switches lights have three position When the switch is in the OFF position the interior light does not illuminate re gardless of door position When the switch is in the center O posi tion the light illuminates when a door is opened 2 34 Instruments and controls e When the switch is in the ON position the interior light illuminates whether any door is open or closed amp CAUTION Do not use for extended periods of time with the engine stopped This could result in a discharged battery LUGGAGE When the back door is opened the luggage compartment
291. teps 1 Position the child restraint on the seat Always follow the restraint manufactur er s instructions Seats restraints and supplemental air bag systems 1 59 Front facing if 4 psan q Jj ARS1177 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing PULL to engage automatic locking mode ARS1178 3 Pull on the shoulder belt until all of the belt is fully extended At this time the seat belt retractor is in the automatic locking mode child restraint mode It reverts back to emergency locking mode when the seat belt is fully retracted 1 60 Seats restraints and supplemental air bag systems Front facing Front PULL to tighten ARS1179 4 Allow the seat belt to retract Pull up on the shoulder belt to remove any slack in the belt Front facing Front ARS1180 5 Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure it is securely held in place 6 Check that the retractor is in the auto matic locking mode by trying to pull more seat belt out of the retractor If you can not pull any more belt webbing out of the retractor the seat belt is in t
292. ter vents and to the front and rear floor outlets Bi level is also a cooling mode when high sun load conditions are present with cool temperatures With the A C system in operation this mode can be used to cool the passenger s or driver s feet under high temperature condi tions With the A C system in operation under high temperature conditions improved cooling can be obtained by moving the air control dial to the MAX A C position 1 Move the air control dial to the po sition 2 Turn the fan control dial to the desired position 3 Move the temperature control dial to the desired position Heating and defogging This mode heats the interior and defogs the windshield This mode directs air to the defroster and the front and rear floor outlets Rear passenger heat is provided by the front system through floor outlets located under both front seats 1 Move the air control dial to the amp po sition 2 Turn the fan control dial to the desired position 3 Move the temperature control dial to the desired position When the position is selected the air conditioner automatically turns on however the indicator light will not illu minate if the outside temperature is more than 45 F 7 C This dehumidifies the air which helps defog the windshield The air recirculation mode automatically turns off allowing outside air to be drawn into the passenger compartment which helps defog the winds
293. that brightness is properly adjusted and set it properly The temperature in the vehicle is below 30 F or above 113 F Check again when the temperature is between 30 F and 113 F The power was turned off when driving on bumpy roads No sound through headphone Severe vibration to the operation panel acti vated the DEW HEAT sensor Poor connection Press the POWER button again to turn the power ON Check jack No sound through vehicle speakers Speaker control button is in OFF position Check speaker control button Disable the RSEM Desire radio but video system sound is heard Media button is set to VCP through vehicle s speakers 4 44 Heater air conditioner and audio systems Turn radio on SPECIFICATIONS VCP General Specifications e Format e Signal system e Recording system Video heads e Audio heads e Control head e Erase e Loading e Sensors e Power consumption e Power requirement e Dimensions WxHxD e Weight VCP e S N ratio e Frequency response VHS standard Standard NTSC 3 58 Rotary double azimuth Four head helical scanning DA 4 Rotary heads Lineary 1 HiFi 2 Rotary 1 Stationary 1 Full Track 1 Audio Central loading Dew Heat 12W DC 12V 265 x 94 x 260 mm 2 7 kg More than 70dB A wt for Hi Fi 1kHz More than 60dB A wt for Lin ear 1kHz 0 3dB 20Hz 20 kHz Video Monitor Specifications e Display type e Screen
294. the sun drive for two or three minutes with the windows open to vent hot air from the passenger compart ment Then close the windows This allows the air conditioner to cool the interior more quickly The air conditioning system should be operated for about ten minutes at least once a month This helps pre vent damage to the system due to lack of lubrication If the engine coolant temperature gauge exceeds the H hot position turn the air conditioner off See If your vehicle over heats in the In case of emergency section for additional information AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating cooling or defrosting DEFROSTING D DEFOGGING lt a Air passed through heater core Fan control Temperature Air flow control dial control dial dial CoS Rear seat A C fan control Air conditioner if so equipped button A C near plang Air flow Temp Fan switch if so equipped control control control OFF automaticall OFF Hy HOT 4 turns on y RIGHT WHA0009 Heater air conditioner and audio systems 4 7 BI LEVEL HEATING Fan control Temperature Air flow control dial control dial dial Rear seat A C fan control Air conditioner if so equipped n butto Air flow Temp control control w O Ad HOT RIGHT Rear seat A C fan control AIC switch
295. this manual e For additional information refer to Wheels and tires in the Do it yourself section of this manual 5 16 Starting and driving COLD WEATHER DRIVING FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing apply de icer or glycerin through the key hole If the lock becomes frozen heat the key be fore inserting it in the key hole ANTI FREEZE In the winter when it is anticipated that the temperature will drop below 32 F 0 C check the anti freeze ethylene glycol base to assure proper winter protection For de tails see Engine cooling system in the Do it yourself section of this manual BATTERY If the battery is not fully charged during extremely cold weather conditions the bat tery fluid may freeze and damage the bat tery To maintain maximum efficiency the battery should be checked regularly For details see Battery in the Maintenance and do it yourself section of this manual DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti freeze drain the cooling system by opening the drain valves located under the radiator and on the engine block Refill before operating the vehicle See Chang ing engine coolant in the Maintenance and do it yourself section of this manual TIRE EQUIPMENT 1 SUMMER tires are of a tread design to provide superior performance on dry pavement However the performance of these tir
296. through six for each band AM FM1 and FM2 SEEK tuning Push the SEEK d or gt buttons to find the next broadcast station Pushing the lt q SEEKS up and button SEEKS down Pushing the button again continues the SEEK function Once the highest broadcast station is reached the radio continues in the SEEK mode at the lowest station Once the lowest broadcast station is reached the radio con tinues in the SEEK mode at the highest station SCAN tuning Push the SCAN tuning button SCAN illumi nates in the display SCAN tuning begins from low to high frequencies and stops at each broadcasting station for 5 seconds Pushing the button again during this 5 sec ond period stops SCAN tuning and remains tuned to that station 4 28 Heater air conditioner and audio systems SELECT STATION SEEK select NEE 12 00 Manual tuning J MEMORIZE 89 335 12 00 Push and hold button ORELO CONFIRM 89 37 12 00 The radio mutes When the sound resumes memorizing is complete AHA1108 Station memory operations Six stations can be set for the AM band Twelve stations can be set for the FM band six for FM1 six for FM2 1 Push the FM or AM buttons to select AM FM1 or FM2 The selected band illumi nates in the display 2 Tune to the desired station 3 Push the desired station select button for more than 1 5 seconds The radio mutes
297. ting in this section for proper seat installation proce dures 3 Be sure the second row bench seatback is locked by grasping it and trying to rock it back and forth Also check that the seatback release lever is in the full down Remember that a child restraint left in a position closed vehicle can become very hot Check the seating surface and buckles before placing your child in the child restraint Seats restraints and supplemental air bag systems 1 75 4 Pull the cushion release strap and lower the integrated child safety seat cushion completely Cushion release straps PULL to LOWER cushions ARS1201 NOTE The head restraints on the pas senger bench seat equipped with the integrated child safety seats are not ad justable or removable 1 76 Seats restraints and supplemental air bag systems DISCONNECT chest clip SEPARATE two halves of shoulder harness from belt buckle 5 If connected separate the two halves of the shoulder harness from the belt buckle Also if connected disconnect the chest clip and lay the shoulder harness halves aside Chest clip Safety belt Chest clip unlatched webbing _ latched Squeeze to j release Indicator window showing green to indicate latched Indicator window showing red to indicate unlatched Squeeze top 4 and bottom of clip to separate APD0815 Chest clip Belt buckle 6 Pl
298. to prevent the possibil ity of whipping action damage to the fenders or undercarriage If possible avoid fully loading your vehicle when using tire chains In addition drive at a reduced speed Do not exceed the maximum speed suggested by the tire chain manufacturer Otherwise your vehicle may be damaged and or vehicle handling and performance may be ad versely affected Never install tire chains on TEMPORARY USE ONLY and small size spare tires Do not use tire chains on dry roads SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter 1 A scraper and stiff bristled brush to re move ice and snow from the windows and wiper blades 2 A sturdy flat board to be placed under the jack to give it firm support 3 A shovel to dig the vehicle out of snow drifts 4 Extra window washer fluid to refill the reservoir tank DRIVING ON SNOW OR ICE A WARNING e Wet ice 32 F 0 C and freezing rain very cold snow or ice can be slick and very hard to drive on The ve hicle will have much less traction or grip under these conditions Try to avoid driving on wet ice until the road is salted or sanded Whatever the condition drive with caution Accelerate and slow down with care If accelerating or down shifting too fast the drive wheels will lose even more traction Allow more stopping distance under these conditions Braking should be started sooner than
299. tral 5 Start the engine R Reverse Use this position to back up Always be sure the vehicle is completely stopped Depress the brake pedal then pull the shift lever toward you and move it to the R Reverse position Starting and driving 5 7 N Neutral Neither forward nor reverse gear is en gaged The engine can be started in this position You may shift to N Neutral and restart a stalled engine while the vehicle is moving D Drive Use this position for all normal forward driving 2 Second gear Use for hill climbing or engine braking on downhill grades Do not downshift into 2 at speeds above 63 MPH 100 km h Do not exceed 63 MPH 100 km h in 2 1 Low gear Use 1 when climbing steep hills slowly or driving slowly through deep snow sand or mud or for maximum engine braking on steep downhill grades Do not exceed 38 MPH 60 km h in 1 Do not downshift into 1 at speeds above 38 MPH 60 km h 5 8 Starting and driving Accelerator downshift In D position For rapid passing or hill climbing fully depress the accelerator pedal to the floor This shifts the transmission down into third gear second gear or first gear depending on the vehicle speed Fail safe When the Fail safe operation occurs the next time the key is turned to the ON position the O D OFF light blinks for ap proximately 8 seconds after coming on for 2 seconds While the vehicle can be driven under these cir
300. ttery replacement cceeeeeeee 8 24 6 9 oieeneeerreerpecereceeeteerrreeerrer EAE 8 25 Headlights sviieicitien Seeded tl HS 8 25 FOG NQMUS sssi ooper 8 26 Exterior and interior lights eese 8 27 Wheels and tires escccceseseeceeeeeeseeeeeeeeeeeeseeeees 8 31 Tire PFOSSUNG s scc ccrusceeaccics Saceceteecanseceesasecnences 8 31 TYPOS Ot tIOS eieiei 8 32 Tire CHAIN Ss set evesceceneecegcadstavvideese eaa 8 33 Changing tires and wheels cceeeeeeee 8 33 MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money However some day to day and regular maintenance is essential to maintain your NISSAN s good mechani cal condition as well as its emission and engine performance It is the owner s responsibility to make sure the scheduled maintenance as well as gen eral maintenance is performed As the vehicle owner you are the only one who can ensure that your vehicle receives proper maintenance You are a vital link in the maintenance chain Scheduled maintenance For your convenience both required and optional scheduled maintenance items are described and listed in your Nissan Service and Maintenance Guide You must refer to that guide to ensure that necessary mainte nance is performed on your Nissan at regu lar intervals General maintenance General maintenance i
301. ur child A rear facing child restraint must only be used in the rear seat NISSAN recommends that the child restraint be installed in the rear seat According to accident statistics children are safer when properly re strained in the rear seat than in a front seat e An improperly installed child re straint could lead to serious injury in an accident In general child restraint systems are de signed to be installed with a lap belt or the lap portion of a three point type seat belt In addition this vehicle is equipped with a universal child restraint lower anchor sys tem referred to as the LATCH Lower An chors and Tether for Children system Some child restraints include two rigid or webbing mounted attachments that can be connected to these lower anchors For de tails see LATCH Lower Anchors and Tether for Children system later in this section Child restraints for infants and children of various sizes are offered by several manu facturers When selecting any child re straint keep the following points in mind 1 Choose only a restraint with a label cer tifying that it complies with Federal Motor Vehicle Safety Standard 213 or Cana dian Motor Vehicle Safety Standard 213 2 Check the child restraint in your vehicle to be sure it is compatible with the vehi cle s seat and seat belt system Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recommended practic
302. ur vehicle wheels To compensate for this make a larger than normal turning radius during the turn Crosswinds and rough roads adversely affect vehicle trailer handling possibly causing vehicle sway When being passed by larger vehicles be prepared for possible changes in crosswinds that could affect vehicle handling If swaying does occur firmly grip the steering wheel steer straight ahead and immedi ately but gradually reduce vehicle speed This combination helps to stabi lize the vehicle Never increase speed e Be careful when passing other vehicles Passing while towing a trailer requires considerably more distance than normal passing Remember the length of the trailer must also pass the other vehicle before you can safely change lanes e To maintain engine braking efficiency and electrical charging performance do not use overdrive e Avoid holding the brake pedal down too long or too frequently This could cause the brakes to overheat resulting in re duced braking efficiency When towing a trailer change fluid in the transmission more frequently For addi tional information see the NISSAN Ser vice and Maintenance Guide UNIFORM TIRE QUALITY GRADING Department of Transportation DOT Qual ity Grades All passenger car tires must conform to Federal Safety Requirements in addition to these grades Quality grades can be found where appli cable on the tire sidewall between tread shoulder and ma
303. uses the CD to advance at three times the normal play speed If held for more than three seconds the CD advances at 10 times the normal play speed The volume decreases and the display win dow shows the elapsed time during the entire fast forward period REW Rewind Press this button to reverse the CD mecha nism and move back to a previous point on the disc If held for less than three seconds this button causes the CD to reverse at three times the normal play speed If held for more than three seconds the CD re verses at 10 times the normal play speed The mechanism reverses to the beginning of track 1 and begins play if the button is held continuously The volume decreases and the display window shows the elapsed time during the entire fast reverse period COMP Compression Press this button to activate the compres sion function This function reduces the dynamic range of the CD program material which provides the listener with a more consistent level of volume The display win dow shows a C or COMP dual media radio when the compression button is pushed SHUFFLE Press this button to randomly select the play order of the tracks on a CD When all tracks of one CD have been played the system changes to the next CD in the magazine and proceeds to play the tracks in a ran domly selected order The shuffle feature remains in effect until turned off by pressing the SHUFFLE button again When the shuffle funct
304. veness of the en tire restraint system and increase the chance or severity of injury in an accident PRESS to unfasten THREE POINT TYPE SEAT BELT WITH RETRACTOR FOR SECOND ROW BUCKET SEATS A WARNING e Every person who drives or rides in this vehicle should use a seat belt at all times e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an acci dent you could be thrown into it and receive neck or other serious inju ries You could also slide under the lap belt and receive serious internal injuries e For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly Fastening the seat belt 1 Adjust the seat 2 Slowly pull the seat belt out of the retrac tor and insert the tongue into the buckle until you hear and feel the latch engage The retractor is designed to lock during a sudden stop or on impact A slow pulling motion permits the seat belt to move and allows you some freedom of movement in the seat Seats restraints and supplemental air bag systems 1 45 TAKE UP POSITION low on the hips A APD0830 3 Position the lap belt portion low and snug on the hips as shown 4 Pull the shoulder belt portion toward the retractor to take up extra slack Two buckle seat belt system for the
305. ver Fading Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings It can also occur for several seconds during ionospheric turbu lence even in areas where no obstacles exist Static Caused by thunderstorms electrical power lines electric signs and even traffic lights AUDIO OPERATION PRECAU TIONS Cassette player e To maintain good quality sound NISSAN recommends that you use cassette tapes of 60 minutes or shorter in length e Cassette tapes should be removed from the player when not in use Store cassettes in their protective cases and away from direct sunlight heat dust moisture or magnetic sources e Direct sunlight can cause the cas sette to become deformed The use of deformed cassettes may cause the cassette to jam in the player e Do not use cassettes that have peel ing or loose labels If used the label could jam in the player e If a cassette has loose tape insert a pencil through one of the cassette hubs and rewind the tape firmly Loose tape may cause jamming and wavering sound quality Over a period of time the playback head capstan and pinch roller may gather a tape coating residue as the tape passes over the head This resi due accumulation can cause a weak or wavering sound and should be removed periodically with a head cleaning tape If the residue is not removed periodi cally the player may need to be dis assembled for cle
306. when the select button is pushed 4 When the sound resumes memorizing is complete 5 Other station select buttons can be set in the same manner If the battery is disconnected or if the radio fuse opens the radio memory is canceled In that case reset the desired stations RDS Radio Data System RDS stands for Radio Data System and is a data information service transmitted by some radio stations on the FM band not AM band encoded within a regular radio broadcast Most RDS stations are currently in large cities but many stations are now considering broadcasting RDS data RDS can display e Station name or call sign such as WHER 98 3 e Music or programming type such as Classical Country or Rock e Text Messages such as telephone num bers for dial in requests advertisements and other simple messages e Traffic reports about delays or construc tion Using RDS To turn RDS on push the RDS CLK button until RDS OFF is displayed then press the SEL button until RDS ON is displayed To change display type turn RDS ON then use the SEL button to choose between e SHOW TYPE Music or program type e SHOW NAME Station name or call sign e SHOW TEXT Text Messages such as telephone numbers for dial in requests advertisements and other simple mes sages e SHOW NONE No text display To choose traffic reports press the RDS CLK button until TRAFFIC OFF is dis played
307. ximum section width For example Treadwear 200 Traction AA Temperature A Treadwear Treadwear grade is a comparative rating based on tire wear rate when tested under controlled conditions on specified govern ment test courses For example a tire graded 150 would wear one and a half 1 1 2 times as well on the government course as a tire graded 100 However relative tire performance depends on actual driving conditions and may vary signifi cantly due to variations in driving habits service practices and differences in road characteristics and climate Traction AA A B and C The traction grades from highest to lowest are AA A B and C Those grades repre sent the tire s ability to stop on wet pave ment as measured under controlled condi tions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance A WARNING The traction grade assigned to your ve hicle tires is based on straight ahead braking traction tests and does not in clude acceleration cornering hydro planing or peak traction characteristics Temperature A B and C Temperature grades are A the highest B and C They represent a tire s resistance to heat build up and its ability to dissipate heat when tested under controlled condi tions on a specified indoor laboratory test wheel Sustained high temperature can cause tire material to degenerate reducing tire life Excessive tem
308. zard to other traffic e Turn signals do not work when the hazard warning flasher lights are on The flashers can be actuated with the igni tion switch either OFF or ON Some state laws may prohibit the use of the hazard warning flasher switch while driving 2 20 Instruments and controls HORN HEATED SEATS if so equipped PUSH SIC1280 To sound the horn push the center pad area of the steering wheel Driver side WRS0088 The front seats are warmed by built in heat ers The switches are located on the seats and can be operated independently of each other The indicator light in the switch will illumi nate when turned on The heater is controlled by a thermostat automatically turning the heater on and off The indicator light will remain on as long as the switch is on When the vehicle s interior is warmed or before you leave the vehicle be sure to turn the switch off CAUTION Do not use the seat heater for extended periods or when no one is using the seat Do not put anything on the seat which insulates heat such as a blan ket cushion seat cover etc Other wise the seat may become over heated Do not place anything hard or heavy on the seat or pierce it with a pin or similar object This may result in damage to the heater Any liquid spilled on the heated seat should be removed immediately with a dry cloth When cleaning the seat never use gasoli

2002 Nissan Quest Owners Manual

Contents

Download Pdf Manuals

Related Search

Related Contents