Dell Latitude D510 Service Manual
Contents
1. 1 fan cable routing fan cable connector 6 Remove the two M2 5 x 8 mm screws from the fan and pull the fan away from the system board 1 M2 5 x 8 mm screws 2 fan cable connector 4 system board connector Back to Contents Page Back to Contents Page Hard Drive Dell Latitude D510 Service Manual Removing the Hard Drive Installing the Hard Drive 3 Removing the Hard Drive From Its Carrier Removing the Hard Drive A CAUTION If you remove the hard drive from the computer when the drive is hot do not touch the metal housing of the hard drive A CAUTION Before working inside your computer read the safety instructions in your Product Information Guide NOTICE To prevent data loss shut down your computer before removing the hard drive Do not remove the hard drive while the computer is on in standby mode or in hibernate mode NOTICE Hard drives are extremely fragile even a slight bump can damage the drive K NOTE Dell does not guarantee compatibility or provide support for hard drives from sources other than Dell 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer upside down Use a standard 1 Phillips screwdriver to remove the two M3 x 5 mm screws 1 M3 x 5 mm screws 2 3 Turn the computer over so that it is upright NOTI CE You cannot remove your hard drive unless you open your display first 4 Open the2. Pin Assignments for I O Connectors Dell Latitude D510 Service Manual USB Connector Video Connector Parallel Connector S Video TV Out Connector Serial Connector EEE 1394 Connector USB Connector 1234 Pin Signal USB5V 54321 109876 15 14 13 12 11 Pin Signal Pin Signal eas ve ae Parallel Connector OOOOOOOOOOOO OOOOOOOOOOO 13 4 4 25 A 44 STROBE 10 ACK poo i sus i aa fre poe as error pos a7 sun OLFTONIoT u PRIwWINit re S Video TV Out Connector Ses fs NN 1 u DCRMA L NC DCMPS L IEEE 1394 Connector 1234 H Back to Contents Page Back to Contents Page Speakers Dell Latitude D510 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the palm rest 3 Note the location of the coin cell battery 4 Remove the speaker cable from the speaker cable routing clips NOTICE To avoid damage to the speaker cable be sure to re route it through both secur
3. 3 Push the new device into the bay until it clicks If the Device Security Screw Is Installed NOTICE To prevent damage to devices place them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on top of them 1 Save and close any open files exit any open programs and shut down the computer 2 If the computer is connected to a docking device docked undock it See the documentation that came with your docking device for instructions o NOTICE To prevent damage to devices place them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on top of them 3 Close the display and turn the computer upside down Use a 1 Phillips screwdriver to remove the optical device security screw from the bottom of the computer 1 M2 x 3 mm screw 5 Press the device latch release so that the latch release pops out 6 Pull the device by the latch release to remove the device from the module bay 7 Push the new device into the bay until it clicks Back to Contents Page
4. DIMM A before you install a module in the connector labeled DIMM B o NOTI CE Do not attempt to install non DDR2 memory modules in the connectors Installing incompatible memory modules can damage the connectors 4 Ground yourself and install the new memory module a Align the notch in the module with the slot in the center of the connector b Slide the edge of the module firmly into the connector and rotate the module down until you feel a click If you do not feel the click remove the module and reinstall it K NOTE If the memory module is not installed properly the computer will not boot No error message indicates this failure 5 Replace the cover and screw NOTICE If the memory module cover is difficult to close remove the module and reinstall it Forcing the cover to close may damage your computer 6 Insert the battery into the battery bay or connect the AC adapter to your computer and an electrical outlet 7 Turn on the computer If memory has been added as the computer boots it detects the additional memory and automatically updates the system configuration information Modem A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted meta
5. disclaims any proprietary interest in trademarks and trade names other than its own Model PP10L April 2005 Rev A00 Back to Contents Page Before You Begin Dell Latitude D510 Service Manual Preparing to Work Inside Your Computer Recommended Tools Turning Off Your Computer Before Working Inside Your Computer Computer Orientation Screw Identification Preparing to Work Inside Your Computer This section provides procedures for removing and installing the components in your computer Unless otherwise noted each procedure assumes that the following conditions exist You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer You have read the safety information in the Product Information Guide A component can be replaced by performing the removal procedure in reverse order Recommended Tools The procedures in this document may require the following tools 1 4 inch flat blade screwdriver 1 Phillips screwdriver Small plastic scribe Flash BIOS update program floppy disk or CD Turning Off Your Computer o NOTI CE To avoid losing data save and close any open files and exit any open programs before you turn off your computer 1 Shut down the operating system a Save and close any open files exit any open programs click the Start button and then click Shut Down b In the Shut Down window click OK The computer turns off after the operating syst
6. Page Back to Contents Page System Components Dell Latitude D510 Service Manual NOTICE Only a certified service technician should perform repairs on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty NOTICE Unless otherwise noted each procedure in this document assumes that a part can be replaced or if purchased separately installed by performing the removal procedure in reverse order aree 2 optical device T r Back to Contents Page Back to Contents Page Microprocessor Thermal Cooling Assembly Dell Latitude D510 Service Manual Removing the Microprocessor Thermal Cooling Assembly 3 Installing the Microprocessor Thermal Cooling Assembly Removing the Microprocessor Thermal Cooling Assembly A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE Disconnect the computer and any attached devices from electrical outlets and remove any installed batteries 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Remove the captive screw that attaches the display cable to the system board 4 Disconnect t
7. Starting at the edges of the bottom of the display panel use your fingers to separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover Display Panel A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Remove the display bezel 4 Remove the eight M2 x 5 mm screws from the display panel display panel M2 x 5 mm screws 8 5 Lift the display panel rotating it out of the display cover 6 Use the pull tab to disconnect the bottom flex cable connector from the inverter connector top flex cable connector display connector bottom flex cable connector with pull tab 7 Press in both sides of the top flex cable connector and pull it away from the display connector Display Latch A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching a
8. display approximately 2 54 cm 1 in NOTICE When the hard drive is not in the computer store it in protective antistatic packaging See Protecting Against Electrostatic Discharge in your Product Information Guide 5 Slide the hard drive out of the computer Installing the Hard Drive 1 If installing a new drive remove it from its packaging Save the original packaging to use when storing or shipping the hard drive If the drive that you are installing is not packaged in a carrier remove the old hard drive from its carrier and attach the carrier to the new hard drive 2 Ensure that the display is open approximately 2 54 cm 1 inch NOTI CE Use firm and even pressure to slide the drive into place If you force the hard drive into place using excessive force you may damage the connector 3 Press the hard drive cover into the bay until it is fully seated in the bay 4 Turn the computer upside down Use a small screwdriver to tighten the screws 5 Install the operating system for your computer 6 Install the drivers and utilities for your computer Removing the Hard Drive From Its Carrier A CAUTION If you remove the hard drive from the computer when the drive is hot do not touch the metal housing of the hard drive A CAUTION Before working inside your computer read the safety instructions in your Product Information Guide o NOTI CE Hard drives are extremely fragile even a slight bump can damage the drive 1
9. height If one or more corners of the module are higher than the others the module is not seated correctly Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board Replace the parts that you removed in Removing the Microprocessor Module Back to Contents Page Back to Contents Page Display Assembly and Display Latch Dell Latitude D510 Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE You must remove the display assembly before you remove the palm rest 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Open the display assembly approximately 180 degrees and support the display assembly so that it does not open past this position 4 Remove the captive screw that grounds the display cable 5 Disconnect the display cable from the display cable connector on the system board 6 Release the display cable from its routing clips and slide it out from beneath the tab on the palm rest 1 2 display cable 7 Release
10. the two antenna cables from the two antenna securing clips 8 Disconnect one antenna cable from the display by holding the two gold antenna connectors and gently pulling them apart Then disconnect the other antenna cable The gold antenna connectors on each cable are keyed to ensure that they are correctly reconnected display cable antenna cables 2 antenna securing clips 2 9 Remove the four M2 5 x 5 mm screws M2 5 x 5 mm screws 4 10 Rotate the display assembly to a 90 degree angle and lift the display assembly up and out of the computer base Display Bezel A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Remove the display assembly 4 Use a plastic scribe to pry the five display bumpers out of the screw holes located on the front of the bezel 5 Remove the six M2 x 5 mm screws located on the front of the bezel display bumper 4 M2 x 5 mm screws 6 support bracket display bumpers 4 display panel 6 display bezel NOTICE Carefully separate the bezel from the top cover to avoid damage to the bezel 6
11. A00 Back to Contents Page Back to Contents Page Memory Module Modem Mini PCI Card and Optical Devices Dell Latitude D510 Service Manual Memory Module Modem Mini PCI Card Optical Devices Memory Module _ CAUTION Before working inside your Dell computer read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface K NOTE Memory modules purchased from Dell are covered under your computer warranty 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer upside down loosen the captive screw labeled M in the memory module cover and lift the cover o NOTICE To prevent damage to the memory module connector do not use tools to spread the securing clips that secure the memory module 3 If you are replacing a memory module remove the existing module NOTICE Handle memory modules by their edges and do not touch the components on a module a Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up b Remove the module from the connector o NOTI CE If you need to install memory modules in two connectors install a memory module in the connector labeled
12. Dell Latitude D510 Service Manual Before You Begin Display Assembly and Display Latch System Components Palm Rest Memory Module Modem Mini PCI Card and Optical Devices Speakers Hard Drive Base Latch Internal Card With Bluetooth Wireless Technology Fan Keyboard System Board Coin Cell Battery Flashing the BIOS Microprocessor Thermal Cooling Assembly Pin Assignments for I O Connectors Microprocessor Module Notes Notices and Cautions K NOTE A NOTE indicates important information that helps you make better use of your computer NOTI CE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2005 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and Latitude are trademarks of Dell Inc Intel Pentium and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation Bluetooth is a trademark owned by Bluetooth SIG Inc and is used by Dell Inc under license Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc
13. Remove the two screws labeled M2 x 3 2 Use spring tension to gently pry the carrier open near the back of the carrier 3 Lift the hard drive out of the carrier Back to Contents Page Back to Contents Page Keyboard Dell Latitude D510 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer top side up palm rest with touch pad 3 Remove the center control cover a Open the display all the way 180 degrees so that it lies flat against your work surface b Starting on the right side of the computer use a plastic scribe to pry up the center control cover Lift it away from the computer and lay it aside center control cover 4 Remove the keyboard a Remove the two M2 5 x 5 mm screws across the top of the keyboard o NOTI CE The keycaps on the keyboard are fragile easily dislodged and time consuming to replace Be careful when removing and handling the keyboard b Slide the keyboard towards the display until it is free of the palm rest and hold it slightly above the computer to allow access to the ke
14. e 3 Turn the computer upside down 4 Pull the card connector out of the system board connector 5 Pull the card cable to remove the internal card with Bluetooth wireless technology from the computer o NOTI CE When replacing the internal card with Bluetooth wireless technology ensure that the card cable is routed correctly so that you do not damage the cable when you install the hard drive internal card with Bluetooth wireless technology 2 system board connector 3 card connector 4 card cable To replace the internal card with Bluetooth wireless technology l Insert the internal card with Bluetooth wireless technology 2 Ensure that the card cable is routed under the tab 3 Connect the card cable 4 Replace the hard drive Back to Contents Page Back to Contents Page Coin Cell Battery Dell Latitude D510 Service Manual CAUTION Before working inside your Dell computer read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer upside down 3 Depress the coin cell cover latch in the battery bay and rotate it out to remove the coin cell battery cover coin cel
15. em shutdown process finishes 2 Ensure that the computer and any attached devices are turned off If your computer and attached devices do not automatically turn off when you shut down your operating system press and hold the power button for 4 seconds Before Working I nside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety A CAUTION Before you begin any of the procedures in this section follow the safety instructions in the Product Information Guide CAUTION Handle components and cards with care Do not touch the components or contacts on a card Hold a card by its edges or by its metal mounting bracket Hold a component such as a processor by its edges not by its pins NOTICE Only a certified service technician should perform repairs on your computer Damage due to servicing that is not authorized by Dell is not covered by your warranty o0 Fb NOTI CE When you disconnect a cable pull on its connector or on its strain relief loop not on the cable itself Some cables have a connector with locking tabs if you are disconnecting this type of cable press in on the locking tabs before you disconnect the cable As you pull connectors apart keep them evenly aligned to avoid bending any connector pins Also before you connect a cable ensure that both connectors are correctly oriented and aligned NOTI CE To avoid damaging the computer per
16. es 2 antenna connectors on card 2 7 Lower the Mini PCI card toward the inner tabs to approximately a 20 degree angle 8 Continue lowering the Mini PCI card until it snaps into the inner tabs of the connector 9 Ensure that the cables are positioned so that they will not be pinched when you replace the cover 10 Replace the cover o NOTICE If the Mini PCI card cover is difficult to close remove the card and reinstall it Forcing the cover to close may damage your computer Optical Devices Your computer ships with an optical drive installed in the module bay You can install an M2 x 3 mm optical device security screw in the bay if desired to make the device more difficult to remove A CAUTION Before working inside your computer read the safety instructions in your Product Information Guide NOTICE Insert devices into the module bay before you dock and turn on the computer K NOTE You do not need to install the device security screw unless you want to keep the module inside the computer for security purposes If the Device Security Screw Is Not I nstalled NOTICE To prevent damage to devices place them in a safe dry place when they are not installed in the computer Avoid pressing down on them or placing heavy objects on top of them 1 Press the device latch release so that the latch release pops out device latch release 2 Pull the device by the latch release to remove the device from the module bay
17. form the following steps before you begin working inside the computer 1 Ensure that the work surface is flat and clean to prevent the computer cover from being scratched 2 Turn off your computer 3 If the computer is connected to a docking device undock it See the documentation that came with your docking device for instructions o NOTI CE To disconnect a network cable first unplug the cable from your computer and then unplug it from the network port or device 4 Disconnect any telephone network and USB cables from the computer 5 Disconnect your computer power supply and all attached devices from their electrical outlets NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface o NOTICE To connect a network cable first plug the cable into the network port or device and then plug it into the computer 6 Remove any installed PC Cards from the PC Card slot 7 Close the display and turn the computer upside down on a flat work surface o NOTI CE To avoid damaging the system board you must remove the main battery before you service the computer 8 Slide and hold the battery bay latch release on the bottom of the computer and then remove the battery from the battery bay 9 Remove any installed memory modules modems Mini PCI cards internal cards with B
18. he display cable from the display cable connector on the system board 5 Release the display cable from its routing clips and slide it out from beneath the tab on the palm rest 6 Release the two antenna cables from the two antenna securing clips 7 Disconnect one antenna cable from the display by holding the two gold antenna connectors and gently pulling them apart Then disconnect the other antenna cable The gold antenna connectors on each cable are keyed to ensure that they are correctly reconnected antenna connectors 2 8 In consecutive order loosen the four captive screws labeled 1 through 4 that secure the microprocessor thermal cooling assembly to the system board 9 Lift the microprocessor thermal cooling assembly up and to the right to remove it from the system board I nstalling the Microprocessor Thermal Cooling Assembly o NOTI CE Ensure that you do not trap any cables beneath the microprocessor thermal cooling assembly when you replace it l Slip the left side of the microprocessor thermal cooling assembly underneath the palm rest and then place the assembly over the microprocessor NOTICE While tightening the screws ensure that the cooler plate is no higher than the screw heads 2 Tighten the four captive screws labeled 1 through 4 in consecutive order incorrectly installed heat sink 2 correctly installed heat sink 3 Slide the display cable behind the tab on the palm res
19. ing clips When inserting it back into each routing clip slightly bend open the clip with your finger insert the cable and then press the clip closed 5 Disconnect the speaker connector from the system board connector NOTICE Handle the speakers with care to avoid damaging them 6 Remove the M2 5 x 5 mm screw labeled B from the speakers 7 Gently pull the front of the computer base outward while lifting the speakers speaker connector M2 5 x 5 mm screw labeled B coin cell battery coin cell battery compartment computer base 8 Disconnect the coin cell battery from the speakers NOTICE When replacing the speakers be sure to replace the coin cell battery in its compartment Back to Contents Page Back to Contents Page System Board Dell Latitude D510 Service Manual Removing the System Board Installing the System Board Removing the System Board A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide The system board s BIOS chip contains the Service Tag which is also visible on a barcode label on the bottom of the computer The replacement kit for the system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board NOTICE Disconnect the power supply and any attached devices from electrical outlets and remove any installed batteries NOTICE To prevent damage to co
20. installed properly 2 Turn on the computer and press lt F12 gt during POST to access the Boot Menu NOTE If you wait too long and the operating system logo appears continue to wait until you see the Microsoft Windows desktop Then shut down your computer and try again 3 Insert the flash BIOS update program floppy or CD and select boot from CD DVD CD RW Drive 4 Select Upgrade your system BI OS from the menu Follow the instructions that appear on the screen The computer continues to boot and updates the new BIOS When the update is complete the computer automatically reboots NOTE To enter the system setup program press F2 during POST Press Esc and select Save Exit if you make modifications otherwise select Exit and then press Enter to exit the system setup 5 Remove the flash BIOS update program floppy or CD from the drive Back to Contents Page Back to Contents Page Internal Card With Bluetooth Wireless Technology Dell Latitude D510 Service Manual CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide o NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the hard driv
21. l cover latch coin cell battery cover 4 Pull the coin cell battery straight out of the computer base 5 Disconnect the coin cell battery cable connector from the battery connector 1 battery connector 2 coin cell battery Back to Contents Page Back to Contents Page Microprocessor Module Dell Latitude D510 Service Manual Removing the Microprocessor Module Installing the Microprocessor Module Removing the Microprocessor Module A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface NOTICE Do not touch the processor die Press and hold the microprocessor down on the substrate on which the die is mounted while turning the cam screw to prevent intermittent contact between the cam screw and microprocessor NOTICE To avoid damage to the microprocessor hold the screwdriver so that it is perpendicular to the microprocessor when turning the cam screw 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard NOTICE To ensure maximum cooling for the microprocessor do not touch the heat transfer areas on the microprocessor thermal cooling assembly The oils in your skin reduce the heat tra
22. l surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer upside down loosen the captive screw labeled M from the memory module cover and lift the cover 3 If you are replacing a modem remove the existing modem a Remove the M2 x 3 mm screw from the modem 1 pull tab 4 modem connector on system board 3 mdem EP b Use the pull tab to disconnect the modem from the modem connector on the system board c Disconnect the modem cable from the modem 4 Connect the modem cable to the modem o NOTI CE Do not press down on the left side of the modem side with the modem cable connection while installing it Align the connector on the bottom of the modem with the modem connector on the system board and then press down on the right side of the modem to seat both connectors 6 Replace the M2 x 3 mm screw 7 Replace the cover and captive screw o NOTICE If the memory module cover is difficult to close remove the module and reinstall it Forcing the cover to close may damage your computer Mini PCI Card If you ordered a Mini PCI card when you ordered your computer Dell has already installed the card for you CAUTI ON Before working inside your computer read the safety instructions in your Product I nformation Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your c
23. luetooth wireless technology backup batteries and optical devices 10 Remove the hard drive Computer Orientation Screw Identification When you are removing and replacing components print this section as a guide to keep track of the screws The placemat provides the number of screws and their sizes js E e H H H H M2x3mm M2x3mm M2 x 4 mm M2 x 5 mm m e D HH tii HI H M3x5mm M25x5mm M25x8mm M3x3mm Optical Device Hard Drive Keyboard optional security screw 2 each 2 each 1 each i H M2 x 3 mm Modem Hard Drive Carrier Display Bezel 1 each 2 each display bumpers 5 each 6 each T z M2 x 3 mm M2 x 5 mm M3 x 3 mm Display Panel 8 each i H M2 x 5 mm Display Assembly Back to Contents Page 4 each M2 5 x 5 mm Speakers 1 each M2 5 x 5 mm Display Latch 1 each E H M2 x 4 mm Ja H M2 5 x 8 mm Palm Rest 4 each m M2 5 x 5 mm 14 each M2 5 x 8 mm System Board 2 each Back to Contents Page Flashing the BI OS Dell Latitude D510 Service Manual NOTICE To avoid damaging the system board ensure you are connected to a known good electrical outlet and that you do not interrupt the BIOS flash process Loss of power or an interruption during the BIOS flash process can cause damage to the system board 1 Ensure that the AC adapter is plugged in and that the main battery is
24. mponents inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the palm rest 3 Remove the microprocessor thermal cooling assembly 4 Remove the microprocessor 5 Remove the speakers 6 Remove the two M2 5 x 5 mm screws labeled B 7 Turn the computer upside down and remove the four M2 x 3 mm screws labeled B that secure the system board to the computer base 1 M2 x 3 mm screws labeled B 4 8 Grab the back of the computer base in the center and pull down slightly so that the two system board securing clips clear their slots and then pull out the system board 1 1 system board securing clips 2 I nstalling the System Board 1 Follow all of the steps in Removing the System Board in reverse order NOTICE Before turning on the computer replace all screws and ensure that no stray screws remain inside the computer Failure to do so may result in damage to the computer 2 Turn on the computer NOTE After replacing the system board enter the computer Service Tag into the BIOS of the replacement system board 3 Insert the floppy disk or CD that accompanied the replacement system board into the appropriate drive and follow the instructions that appear on the screen Back to Contents
25. n unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Remove the display assembly 4 Remove the display bezel 5 Remove the display panel o NOTICE A strip of copper foil may be present beneath the support bracket on some systems ensure that you do not tear this foil while removing the bracket 6 Remove the M2 x 4 mm screw that secures the support bracket to the top cover 7 Lift the support bracket out of the top cover and then remove the display latch K NOTE Ensure that the support bracket is upright when you replace the display latch 1 top cover 2 M2 x 4 mm screw 1 3 support bracket 4 display latch Back to Contents Page Back to Contents Page Fan Dell Latitude D510 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard 3 Remove the palm rest 4 Pull straight up on the fan cable connector to disconnect it from the system board connector 5 Free the fan cable from the cable routing pegs on the system board
26. nsfer capability of the thermal pads 3 Remove the microprocessor thermal cooling assembly NOTICE When removing the microprocessor module pull the module straight up Be careful not to bend the pins on the microprocessor module 4 Use a small flat blade screwdriver to rotate the ZIF socket cam screw counterclockwise until it comes to the cam stop ZIF socket cam screw K NOTE The ZIF socket cam screw secures the microprocessor to the system board Take note of the arrow on the ZIF socket cam screw 5 Lift out the microprocessor module I nstalling the Microprocessor Module o NOTI CE Ensure that the cam lock is in the fully open position before seating the microprocessor module Seating the microprocessor module properly in the ZIF socket does not require force NOTICE A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket 1 Align the pin 1 corner of the microprocessor module with the pin 1 corner of the ZIF socket and insert the microprocessor module Ea NOTE The pin 1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin 1 corner of the ZIF socket NOTI CE You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket When the microprocessor module is correctly seated all four corners are aligned at the same
27. omputer s electronic components You can do so by touching an unpainted metal surface NOTI CE Handle components and cards by their edges and avoid touching pins and contacts oo OP NOTICE 2 4 GHz Wireless LAN PC Cards may be removed and installed by the user Follow the instructions in Preparing to Work Inside Your Computer 2 Turn the computer upside down and loosen the captive screw labeled C on the Mini PCI card cover 3 Place your finger under the cover at the indentation and lift up the cover 4 f a Mini PCI card is not already installed go to step 5 If you are replacing a Mini PCI card remove the existing card a Disconnect any attached cables from the Mini PCI card o NOTICE To prevent damage to the Mini PCI card connector do not use tools to spread the securing clips that secure the card b Release the Mini PCI card by spreading the securing clips until the card pops up slightly C Lift the Mini PCI card out of its connector NOTICE In the next step ensure that the antenna cables extend over the edge of the computer so that they are not trapped beneath the new Mini PCI card 5 Align the new Mini PCI card with the connector at a 45 degree angle and press the Mini PCI card into the connector 6 Connect the antenna cables from the computer to the antenna connectors on the Mini PCI card o NOTI CE The connectors are keyed for correct insertion do not force the connections antenna cabl
28. static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the keyboard NOTICE You must remove the display assembly before you remove the palm rest the display hinges pass through the back of the palm rest 3 Remove the display assembly 4 Turn the computer upside down and remove the 14 M2 5 x 8 mm screws M2 5 x 8 mm screws 14 5 Turn the computer top side up and remove the three M2 5 x 5 mm screws labeled P from the top of the palm rest 6 Remove the M2 5 x 5 mm screw labeled P from the metal shield M2 5 x 5 mm screws labeled P 4 7 Use the touch pad connector tab to disconnect the touch pad connector from the system board 1 touch pad connector 2 system board connector NOTI CE Carefully separate the palm rest from the computer base to avoid damage to the palm rest 8 Starting at the back center of the palm rest use your fingers to separate the palm rest from the computer base by gently lifting up the palm rest while pressing down on the back of the computer base NOTE When you reinstall the palm rest attach the right side of the palm rest first and ensure that the modem ends of the antennae cables are visible in the PCI card compartment on the base of the computer Back to Contents Page Back to Contents Page
29. t and place it between its routing clips 4 Attach the display cable to the display panel connector on the system board 5 Reconnect the two antenna cables and then secure them into the two antenna securing clips Back to Contents Page Back to Contents Page Dell Latitude D510 Service Manual Notes Notices and Cautions K NOTE A NOTE indicates important information that helps you make better use of your computer NOTI CE A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A CAUTION A CAUTION indicates a potential for property damage personal injury or death Information in this document is subject to change without notice 2005 Dell Inc All rights reserved Reproduction in any manner whatsoever without the written permission of Dell Inc is strictly forbidden Trademarks used in this text Dell the DELL logo and Latitude are trademarks of Dell Inc Intel Pentium and Celeron are registered trademarks of Intel Corporation Microsoft and Windows are registered trademarks of Microsoft Corporation Bluetooth is a trademark owned by Bluetooth SIG Inc and is used by Dell Inc under license Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products Dell Inc disclaims any proprietary interest in trademarks and trade names other than its own Model PP10L April 2005 Rev
30. yboard connector C Pull the keyboard connector tab to disconnect the keyboard connector from the system board d Setthe keyboard aside M2 5 x 5 mm screws 2 keyboard connector tab keyboard connector K NOTE When you replace the keyboard ensure that the keyboard tabs are completely secured beneath the palm rest to avoid scratching it Back to Contents Page Back to Contents Page Base Latch Dell Latitude D510 Service Manual A CAUTION Before performing the following procedures read the safety instructions in your Product Information Guide NOTICE To prevent damage to components inside your computer discharge static electricity from your body before you touch any of your computer s electronic components You can do so by touching an unpainted metal surface 1 Follow the instructions in Preparing to Work Inside Your Computer 2 Remove the palm rest 3 Remove the speakers 4 Press in the release button slightly press together the two securing clips and then pull the base latch straight up and away from the computer base 2 base latch release button securing clips 2 computer base Back to Contents Page Back to Contents Page Palm Rest Dell Latitude D510 Service Manual CAUTI ON Before performing the following procedures read the safety instructions in your Product I nformation Guide NOTICE To prevent damage to components inside your computer discharge
Download Pdf Manuals
Related Search