AV-425-RF - Avlite Systems
Contents
1. 185 Fig 4 Radio Controller Side View Fig 5 Radio Controller Front View LCD Screen MENU Button SEND Button UP Button DOWN Button 6 Di pole Omni Directional Right Angle Whip Antenna NO oc PWD gt Charging Port IP68 sealed plug Charger not shown Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Assembly amp Installation of Radio Controller The installation of the Radio Controller includes the following steps e Unpacking e Initial Inspection e Assembling amp Charging the Radio Controller e Using the Radio Controller Components Your pelican case contains the following e 2 4GHz Radio Controller e Charger e Power Supply for charger e Programming Cable Please contact your Avlite office if there is any hardware missing Initial inspection Inspect the Radio Controller for damage If there is any damage please contact your Avlite office Retain original packing material for possible future use Assembly amp Charging The Radio Controller can be activated after raising the aerial into the upright position see Fig 5 It is advisable to charge the Radio Controller before use Turning the Unit On To turn the unit on lift the red missile cover and turn the switch to the ON position The radio controller will take 5 seconds to start up and it may take up to 30 seconds for the embedded RF Module to2. Roto Moulded Products and accessory products Accessory Products will be free from defective materials and workmanship under normal and intended use subject to the conditions hereinafter set forth for a period of twelve 12 months from the date of purchase by the original purchaser 3 Avlite Systems warrants that any Avlite aviation products other than the Telemetry Products Roto Moulded Products and Accessory Products Avlite Products will be free from defective materials and workmanship under normal and intended use subject to the conditions hereinafter set forth for a period of three 3 years from the date of purchase by the original purchaser 4 Avlite Systems will repair or replace at Avlite s sole discretion any Telemetry Products Roto Moulded Products Accessory Products or Avlite Products found to be defective in material and workmanship in the relevant warranty period so long as the Warranty Conditions set out below are satisfied 5 If any Telemetry Products or Avlite Products are fitted with a rechargeable battery Avlite Systems warrants the battery will be free from defect for a period of one 1 year when used within original manufacturer s specifications and instructions Warranty Conditions This Warranty is subject to the following conditions and limitations 1 The warranty is applicable to lanterns manufactured from 1 1 2009 2 The warranty is void and inapplicable if a the product has b
3. fa Lens Design 16 segment multi focus lens Patent pending Mounting 4 hole 200mm bolt pattern Height mm inches 507 20 Width mm inches 233 91 5 Mass kg lbs 14 307 8 Product Life Expectancy Up to 12 years Environmental Factors Humidity to 10076 MIL STD 810F Icing 22kg per square inch Wind Speed Up to 160kph Shock MIL STD 202G Test Condition G Method 213B Vibration MIL STD202G Test Condition B Method 204 Certifications EN61000 6 3 1997 EN61000 6 1 1997 Quality Assurance ISO9001 2008 Waterproof IP68 Intellectual Property Patents Patents pending Trademarks AVLITE is a registered trademark of Avlite Systems Warranty 3 year warranty Options Available s EE Activated Lighting Control 8 Without RF Radio Control m Avlite www avlite com Activation AV 425 RF Radio Controlled Solar Aviation Light Charging the Battery New lights should be left in the sun for several days to ensure battery is charged before placing in service Preferred Installation Location For best light performance ensure solar modules are not covered and are in clear view of the sky with no shadows Lantern Operation The AV 425 RF is activated via the ON OFF switch at the base of the unit l amp multi point regulator 01 06 Item Description Quantity solar panels 1 AV425 Base 1 2 AV425 Lens Assembly 1
4. 3 Battery 12v 24Ah 1 4 Battery Clamp 1 Wy 5 Washer M4 2 4 7 6 M4 Cap Screw 2 Lp 1227 7 M5 Nylock Nut 2 IFS Wy SEES WY 8 O Ring ID 145 x 4 0 1 SSSS Uy 9 Socket Head Screw M6 x 16 4 SESS Wy 10 Mounting Insert 4 SEES WY Wy 11 External Charging Port 1 SS Uy 0 12 ON OFF Switch 1 3 SEES VA 13 Momentary Button 1 VO SS AZ SY A i LL MD 2 Fig 2 AV 425 RF Solar Light components Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Er Radio Controller The Avlite Radio Controller is a compact handheld unit that allows complete control of the airfield lighting system The unit allows for easy activation inspection and testing of the airfield lights The Avlite Radio Controller works on the 2 4GHz ISM Band using a low power RF module The backlit LCD can be seen during day or night The straightforward menu makes the ALS easy to operate The Avlite Radio Controller comes standard with an IP68 rated charging plug omni directional antenna and ON OFF switch and cover The Radio Controller and charger come in an IP68 Pelican Case to protect it from the harsh environment to which it may be subjected The Avlite Radio Controller can be rack mounted in a standard 19 rack for use with other airfield electronic equipment such as Pilot Activated Lighting Control PALC Avlite www avlite com
5. 56 78 91 01 11 21 31 41 Using the UP or DOWN keys select any combination from 00000000000000000000 to FFFFFFFFFFFFFFFFFFFF Record and keep this Encryption key secure in case the controller becomes lost or broken Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light The encryption key can be re entered into the new controller without the need to reprogram all the lights in the Radio Control System Encryption key cannot be 00000000000000000000 Press SEND to save the Radio Control System settings Note Failure to select appropriate settings and save the settings will result in the Radio Control System not being appropriately optioned Congratulations you have now set up your Radio Control System please continue to the next section to setup each light in the system Section 2 Programming the light using the cable interface and hand held controller NOTE In this programming mode it is necessary to press send to save each option as each option is selected in the sub menu before moving to the next sub menu item Failure to press send before moving to the next menu item will result in selections not being saved 1 The programming port is located under the light head It is necessary to remove the light head to access this programming port Ensure that the light is turned off at the red master switch on the control panel at the base of
6. Runway Edge Light Height Diagram AV4 amp 25 on Frangible Mount 24 High Between 2ft and 5ft Between 6ft and 10ft from Runway Edge from Runway Edge maximum light fixture the light fixture height may height is 14 inches increase 2 inches per foot At 10ft from Runway Edge Note A 6 inch clearance must maximum light fixture be maintained between the light height is 30 inches fixture and any overhanging part of an aircraft Installing the Light Assembly to the Frangible Stake Mount The completed AV 425 RF mount plate assembly is to be mounted on the stake in firm soil not loose sand screenings or other unbound material a Fit the AV 425 RF on the top of the mounting plate Insert bolts through the four holes in the mount entering from the bottom Install a penny washer and a Nylock nut on each bolt Tighten Nylock nuts b Use a sledge hammer to drive the stake into the soil at the chosen location Drive the stake down until the bottom of the stake sleeve is at ground level c Fitthe AV 425 RF and mounting plate assembly on top of the stake The point of frangibility should be completely clear of the stake sleeve or ground support hardware Use the socket head cap screws supplied to hold the frangibility point above the sleeve Using a 6mm Allen key tighten the bottom socket head cap screws against the stake sleeve Note After adjustments ensure all nuts and bolts are tightened securely and all tools spar
7. Solar Aviation Light W X White or amber runway lights Os Bi directional threshold and runway end light units red to departing aircraft and green to landing aircraft Sequenced flashing approach lights Os Os Os Os Os Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light MEME FPFPF E J FWEFFF NM mMMR e M IW J J ll Runway End Identifier Light REIL The AV 425 RF is available in a REIL configuration The AV 425 RF REIL W must be ordered preset from the factory It is not possible to configure a REIL from a standard AV 425 RF runway edge light REILS will be pre programmed and clearly labelled upon dispatch REILS from the same light group and same REIL group must be installed together The recommended flash character for a REIL is 112 120 FPM Light groups Light groups are used to enable control of separate sections of the airfield lighting system For example Runway1 Runway 2 Taxiway Obstruction and REILS can all be independently controlled by the ALS RF controller This function allows the Air Traffic controller to turn on or off different sections of the airfield as required Please refer to Radio Control System Setup Section 2 Programming the light using the cable interface and handheld controller paragraph D on light groups for information on how to set a li
8. been completed For addional diagnostic information please see Section 3 of the Radio Control System Setup section of this manual EXTERNAL POWER Diagnostic Checks for external power connection NODE MAIN NET Diagnostic Checks which lights are nodes in the main network NODE SUB NET Diagnostic Checks which lights are nodes in the sub network BATTERY HEALTHY Diagnostic Battery above 12 5V BATTERY LOW Diagnostic Battery above 10 5V but below 12 5V BATTERY FLAT Diagnostic Battery below 10 5V Diagnostic Pass 1 1 second flash OAS J L A 1 Second 1 Second 1 Second Diagnostic Fail 2 x 300 milli second flashes AS Md X LLL A 1 Second 300 ms 400ms 300 ms 1 Second Radio Encryption The AV 425 RF is fitted with 128bit Radio Encryption This includes user adjustable encryption keys and 12 user adjustable channel settings Synchronization The integrated mesh network radio system can provide true synchronization flash patterns including flare paths and approach sequences Sending Commands Every time the SEND button is pressed a command is sent containing all the current settings in the Radio Controller The SEND button can be used after changing one setting or after changing multiple settings Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light rl Radio Control System Setup Your radio control system has been shippe
9. return freight of its choice A returned product must be accompanied by a written description of the defect and a photocopy of the original purchase receipt This receipt must clearly list model and serial number the date of purchase the name and address of the purchaser and authorised dealer and the price paid by the purchaser On receipt of the product Avlite Systems will assess the product and advise the customer as to whether the claimed defect is covered by this warranty 8 Avlite Systems reserves the right to modify the design of any product without obligation to purchasers of previously manufactured products and to change the prices or specifications of any product without notice or obligation to any person Input voltage shall not exceed those recommended for the product 10 Warranty does not cover damage caused by the incorrect replacement of battery in solar lantern models 11 This warranty does not cover any damage or defect caused to any product as a result of water flooding or any other acts of nature 12 There are no representations or warranties of any kind by Avlite or any other person who is an agent employee or other representative or affiliate of Avlite express or implied with respect to condition of performance of any product their merchantability or fitness for a particular purpose or with respect to any other matter relating to any products Limitation of Liability To the extent permitted by acts and regulation
10. the new battery 10 Place battery back inside light body and position the upper battery bracket in the top of the chassis 11 Secure using 2 x M4 Cap screws amp washers and 2 x M5 Nylock nuts and washers 12 Feed all wiring back inside light body and make sure the o ring is properly placed at the top of the light body 12 Please realign bidirectional indicators on teh base with the light head to ensure correct alignment of the light output on the runway 13 Place the top lens assembly back onto the light body and replace 4 socket head screws Half tighten all 4 socket head screws and then fully tighten each socket head screw to ensure an even seal Recommended torque settings for Fitment of Light Heads to Solar Base units using the 4 Hex Bolts supplied It is recommended that the bolts for holding the light heads to the Solar Base units have a torque setting applied of 3Nm for a satisfactory seal Applying a higher Torque setting is not recommended and may void warranty If in doubt please contact your local Avlite representative 14 To test place dark cover towel or jacket on top of light to activate sensor light will come on Care must be taken to observe the polarity of each wire before they are connected To ensure waterproofing of the unit make sure that there is an even seal AV 425 RF Long Term Battery Storage amp Maintenance If the AV 425 RF is to be placed in storage for an extended period please follow the below
11. to change a solar panel in the unlikely event of damage The top casting is constructed with an integrated handle that helps with any manual handling of the unit The high impact resistant polycarbonate lens ensures even light visibility The solar panels provide efficient and year round charging of the large 12V 20Ah SLA battery The four hole bolt pattern will fit directly onto any 200mm OD mount The AV 425 RF is fitted with an external ON OFF switch this means the light can be turned on once in position with the flick of a switch It is also fitted with an external charging port for charging the battery while it is stored for extended periods When the AV 425 RF is used in conjunction with an RF Network FCC compliant a number of options are available such as the ability to use visible and IR LEDs fitted to the same light head All this is backed by Avlite s industry leading 3 year warranty To suit localised standards the AV 425 RF can be supplied with optic head to comply with either FAA L861 or ICAO Annex 14 photometrics Latest products and information available at www avlite com gora 1510 04 LOSf qns pup SUE piopubois Joefgng INoulim joefqns o CN TA SPECIFICATIONS AV 425 RF Light Characteristics Light Source 16 ultra high intensity LEDs Available colors Red Green White Yell
12. 0 Solar Booster rear view Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light CO Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Avlite Light Warranty V1 2 Activating the Warranty Upon purchase the Avlite Systems warranty must be activated for recognition of future claims To do this you need to register on line Please complete the Online Registration Form at www avlite com Avlite Systems will repair or replace your lantern in the event of electronic failure for a period of up to three years from the date of purchase Avlite Systems will repair or replace any ancillary or accessory products in the event of failure for a period of up to one year from the date of purchase as per the terms amp conditions below The unit must be returned to Avlite freight prepaid Warranty Terms 1 Avlite Systems warrants that any Avlite aviation products fitted with telemetry equipment including but not limited to AIS GSM GPS or RF Telemetry Products will be free from defective materials and workmanship under normal and intended use subject to the conditions hereinafter set forth for a period of twelve 12 months from the date of purchase by the original purchaser 2 Avlite Systems warrants that any rotationally moulded products
13. AV 425 RF Radio Controlled Solar Aviation Light Installation amp Service Manual Version 2 2 Aviite www avlite com AV 425 RF Solar Aviation Light 16 segment multi focus lens Internal 2 4GHz RF module LED light unit with visible and near infrared Integrated 9 lighting outputs handle Global 4 Integrated O userreplaceable adio control solar panels Push button switch to cycle through operational modes 12vdc input for cable connection auxiliary charging External ON OFF port system switch Diam 15 9 x 25 4 slot 0 63 x 1 Iii Ill LET Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light el DD Table of Contents INCTOGUETHON ieri Page 4 TOCHINOIOG Y cocisiesaccacinnesanaivawhaanconstsneddateniisobsniniadsinded 4 AV 425 RF Model 5 Activation 7 Avlite Radio Controller Page 8 Assembly amp Installation of Radio Controller Page 9 Radio Controller Menu i Page 10 Radio Controller Syst
14. Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Solar Panel Replacement The AV 425 RF is built around an internal aluminium chassis The solar panels can be user replaced by a trained technician in the unlikely event that one is broken or damaged during the product life as demonstrated below Follow the steps below or contact support avlite com for more details di 10 1 Remove 4 x socket head cap screws and disconnect the light head from the chassis 2 Remove the upper battery bracket 3 Disconnect the battery 4 Remove the battery Remove 4 x M6 35mm long socket head cap screws to remove the top casting from the chassis Note Be careful not to damage the o rings on each of these screws If replacements are required please use standard 6x1 0mm o ring 6 Slide the rubber corner out of the chassis It may be necessary to lubricate the edges of the solar panels with grease or oil based lubricant if this is difficult to remove 7T Disconnect the faulty solar panelfrom the Auxiliary Power out J5 J6 J7 or J8 8 Remove the faulty solar panel from the aluminium chassis Clean any silicon off the chassis from the solar panel junction box hole and add a new silicone seal to ensure the solar panel is watertight when assembled Repeat the process in the reverse order to replace a new panel Note Make sure the O rings on the top casting and 4 x M6 35mm long socket head c
15. Hz Handheld radio Controller by actuating the red rocket switch on the side of the controller The Menu contains the following Sub menu Press the MENU button to scroll through the Sub Menu a Operation Mode Using the UP and DOWN keys select from the following Always On Dusk till Dawn Standby Advanced Operation Mode If Enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following Visible LEDS IR NVG LEDS Light group Using the UP and DOWN keys select from the following 0 15 Select any one of the 0 15 light groups All Selects all of the light groups Intensity Using the UP and DOWN keys select from the following Low Medium High Timeout Mode Using the UP and DOWN keys select from the following Enabled Low Recommended Disabled Timeout Duration Using the UP and DOWN keys select from the following 1 60 Minutes Flash Code If Enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following 000 to 1FF Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light h Sync Mode If Enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following Full Use for Flare Path or Approach sequence Basic Use for synchronised Fla
16. Property Trademarks Solar Booster is a registered trademark of Avlite Systems Can 3 year warranty E e Specifications subject to change or variation without notice Subject to standard terms and conditions CE AV SB 10 Solar Booster shown with AV 425 RF Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Solar Booster Installation Procedure Preferred Installation Location For best light performance ensure solar modules are not covered and are in clear view of the sky with no shadows Remove the AV SB 10 from the box and remove all packaging Locate the AV SB 10 Solar Booster in a position for best solar collection Remove the bolts from the existing installation Fit the AV SB 10 Solar Booster under the top mounting plate Fit the bolts back through the light mounting plate and AV SB 10 Solar Booster Tighten the bolts securely Important To eliminate the possibility of electrical shorts please read this before connecting the AV SB 10 Solar Booster to the light Remove the Light head from the unit Remove the fuse from the battery positive wire Connect the AV SB 10 Solar Booster to the external charge port on the light Refit the fuse to the battery positive wire and refit the light head Cover the light head to ensure that light activates sm Y kc AV SB 10 Solar Booster front view AV SB 1
17. V STANDBY Operation Mode LEDs are OFF but light will respond to and pass commands sent by the radio controller This mode should be used if the lights have been installed outside but are not currently required Note The light is not completely powered down in a manner suitable for storage If the light is to be stored in a warehouse or other dark environment the ON OFF switch should be turned off DUSK to DAWN Operation Mode The light is turned on and off based on the light sensor input Sensors include a light sensor internal to each light and the light will turn on when the ambient light threshold falls below 100 lux and will turn off once the ambient light threshold reaches 150 lux Advanced Op Mode This enables you to select visible or near IR LEDs The options include VISIBLE LEDs amp IR NGV LEDs Note this menu will not be enabled if the selected Operation Mode is STANDBY Light Group This menu is used to select the current light group The controller can select any one of the 15 individual light groups Taxiway lights sign lights and runway lights are able to be controlled seperately using programmable groups 0 gt 15 or select all radio lights at once Note The units are set with a light group of 0 in the factory LED Intensity Default LOW This menu is used to select the intensity of the LEDs on the light The options include Low Medium amp High a Low LED intensity is set to low setting b Medium LED in
18. ame battery assembly Sealed lead acid and NIMH do not mix If the battery has been deep discharged a prolonged charging time is required to bring the battery back to full capacity Storage Always store batteries in a cool dry place After long storage it is desirable to cycle charge discharge the battery 3 times to restore full capacity Do not mix batteries with metal objects during storage or transportation to avoid accidental short circuit Do not store large quantities of batteries in a densely packed condition when they are in a charged or partially charged state Battery Handling Do not incinerate or dismantle batteries Cell components are corrosive and may be harmful to skin and eyes Do not pull on battery lead wires or connector Excessive force on the leads or connectors can damage the welding joints or other connections Batteries are recyclable Please dispose of properly Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Battery Voltage States of Charge Avlite has provided the following guides for battery states of charge Battery Voltage 12 Volt Sealed Lead Acid State of Charge Voltage 100 12 70 90 12 5 80 12 42 70 12 32 60 12 2 50 12 05 40 11 9 30 11 75 20 11 58 10 11 31 0 10 5 Latest products and information available at www avlite com
19. ap screws are coated in silicon grease before re assembling Recommended torque settings for Fitment of Light Heads to Solar Base units using the 4 Hex Bolts supplied It is recommended that the bolts for holding the light heads to the Solar Base units have a torque setting applied of 3Nm for a satisfactory seal Applying a higher Torque setting is not recommended and may void warranty If in doubt please contact your local Avlite representative The replacement of a solar panel should only be performed by a confident technician Solar panel replacement is undertaken at customer s own risk Avlite will only guarantee an IP68 rating if this is undertaken by Avlite Personnel To test for any leaks remove the gore vent and pressurise the assembled light to 1 5psi Latest products and information available at www avlite com Avlite www avlite com Light will not respond to controller in Radio Control Light will not change between visible and IR NVG modes Light will not change Flash Codes AV 425 RF Radio Controlled Solar Aviation Light Trouble Shooting Possible Cause Different encryption key in the light from the controller Different radio channel in the light light from the controller Encryption turned off in the controller but not in the light Incorrect Light bank selected Advanced Operation not enabled Flash Codes not enabled in the Radio Control System Menu Reenter the encryption key into the
20. ay of the flash sequence or a combination or both If you select Sync Offset value and also Sync delay value the combination offset delay value will be the combined total off both values Using the UP and DOWN keys select from the following 10 23 to 10 23 seconds Press SEND after selection h Sync Delay if Synchronisation is enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following 0 to 99 6 Press SEND after selection Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light i Radio Channel Note There are two sub menus in this menu To toggle between the two Sub menus press both the UP and DOWN keys together at the same time Using the UP or DOWN keys select from Encrypted Unencrypted Using the UP or DOWN keys select from OC 17 Press SEND after selection j Radio Encryption Key If Encryption is Enabled during Radio Control System Programming Section 1 Set the encryption key in banks of 2 digits For Example To set an encryption Key of 12345678910111213141 The digits would be set in pairs of 12 34 56 78 91 01 11 21 31 41 Using the UP and DOWN keys set the encryption key Hold down the key to scroll quickly to the required number Pressing both the UP and DOWN keys together will toggle across the encryption key in banks of 2
21. be configured before a command can be sent Charging the Radio Controller a Unscrew the protective cap from the charging port on the left side of the Radio Controller Insert the charging terminal into the Radio Controller Plug the charger into a wall socket and turn the charger on The light on the charger will flash Green Orange Red then back to Orange papp The charger has a LED to indicate the charge sequence i Green Unit is fully charged The Radio Controller can be left connected in state li Orange Unit is charging The unit will charge for a maximum of 8 hours before automatically shutting down iii Red A fault is occurring please contact Avlite Office Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Ol SD Radio Controller Menu This section of the document will provide a short explanation of all the menu screens on the control unit Operation Mode The Operation Mode defines how the light will respond to different environmental conditions amp user inputs There are three operational modes that can be selected via the controller ON STANDBY amp DUSK to DAWN ALWAYS ON Operation Mode The light is Always On The light will be on both night amp day until it is commanded to OFF While the light is in this mode it will only turn off when the battery drops below the Flat Battery Voltage level AV 425 RF 10 5
22. ble at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light c Flash Code Selection Using the UP or DOWN keys select from Disable Enable d Sync Menu Selection Using the UP or DOWN keys select from Disabled Enabled e Advanced Operation Using the UP or DOWN keys select from Disabled Enabled f Diagnostic Using the UP or DOWN keys select from Disabled Enabled g Radio Information Displays the address of the radio in the ALS2 4GHz Hand Held Controller Note There are no user adjustable settings in this menu item h Radio Channel Note There are two sub menus in this menu To toggle between the two Sub menus press both the UP and DOWN keys together at the same time Using the UP or DOWN keys select from Encrypted Unencrypted Using the UP or DOWN keys select from OC 17 i Radio Encryption Key Note If you change the radio control encryption key in Section 1 it will be necessary to change the encryption key in ALL the lights in the system Using the UP and DOWN keys set the encryption key Hold down the key to scroll quickly to the required number Pressing both the UP and DOWN keys together will toggle across the encryption key in banks of 2 digits Set the encryption key in banks of 2 digits For Example To set an encryption Key of 12345678910111213141 The digits would be set in pairs of 12 34
23. ch on the I O panel Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Possible Cause Light will not operate all Battery is low Recharge battery connect battery night to external power supply or replace battery Light is exposed to ambient light Remove ambient light source or shield light from ambient light Battery continually goes flat Battery has failed Replace battery Solar panels are dirty Clean solar panels Light is installed in the shade Remove shade or move light Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Documentation For future reference please record the follwing data and store securely Controller Encryption Key Controller Serial No Radio Channel Light Bank Location eg Runway 1 Taxiway Runway 2 Light Bank Location 0 Light Bank Location 1 Light Bank Location 2 Light Bank Location 3 Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light AV SB 10 Solar Booster The AV SB 10 Solar Booster can be connected to AV425 light to provide additional solar collection to charge the battery The Solar Booster can be used in areas of reduced sunlight to help ensure optimum battery charge or where longer periods of high intensity m
24. com Solar Calculation amp Operating Capabilities For information relating to charging and power please refer to the Avlite Power Calculator To obtain a copy of the Avlite Power Calculator please contact your Avlite Distributor or email info avlite com r oa ri A dal 1 5 F IL LE 5 i HEN ja Lx LIP II b do qx Select location v xus odd ee d ERE i poaae wwe aD ee sb E aeq Bibi a bung MEME e a 1 HE re Rei amp T ee Saree F m z _ _ _ vt20ct_ 3 ee rmi Select usage fr e 2 t i F e 1 profile M bL ANTI i nr i fr ai a unm gee cum any Rip puce cared i ine I mm od met ia F Pi mE mr Gm Am i ei iiam what Fee Lalelalagas2 aa a ii A i ali al Lid rs li aie daz ga Important Note To ensure the battery is maintained in a healthy state of charge it is recommended that the light battery diagnostic check be performed once per day Important Note Hours of Effective Sunlight are dependent upon the location in the world of the light Effective hours alter with the seasons and this must be taken into account when setting up the Radio Control System Effective sunlight hours for various locations can be found at www sealit
25. d preprogrammed with a default 128 bit encryption key It is not necessary to alter the default encryption key however if required the encryption key can be changed see Secion 1 i Note If you change the radio control encryption key in Section 1 it will be necessary to change the encryption key in ALL the lights in the system To ensure trouble free set up of the Radio control System it is necessary to step through the following set up procedures The setting up of the Radio control system is divided into 3 sections Section 1 Programming the Radio Control System must be done before Section 2 and 3 Section 2 Programming the light using a direct cable connection Section 3 Operating the lights using the controller Section 1 Programming the Radio Control System 1 Foldoutthe aerial on the top of the ALS 2 4 GHz Handheld Radio Controller 2 Turnon the ALS 2 4GHz Handheld Radio Controller by actuating the red rocket switch on the side of the controller 3 Press and hold the menu button for 3 seconds 4 The screen will display the following massage 5 The Menu contains the following Sub menu Press the Menu button to step between the menu items a Screen back light Using the UP or DOWN keys select from 0 100 b Connection Method Using the UP or DOWN keys select from Radio Control standard wireless connection Direct Connection use for programming light Latest products and information availa
26. digits Insert Radio Encryption Key Note Radio Encryption Key must be the same key as set in the Radio Control system section 1 or the light will not respond to the controller Press SEND after selection Note Turn the light off at the red master switch before disconnecting the Hand Held Radio interface cable The light must be depowered before the settings will take effect Repeat this process for every light in the system Important When you have finished programming all of the lights the Radio Controller must be put back into Radio Connection Mode 1 Using the menu key scroll down the submenu to CONNECTION METHOD 2 Using the UP and Down keys select RADIO CONNECTION 3 Press SEND to save settings Failure to place the Radio Controller back into RADIO CONNECTION mode will cause the Radio Controller to be unable to communicate with the lights Congratulations you have now programmed your lights to your Radio Control System please continue to the next section Latest products and information available at www avlite com Aviite www avlite com AV 425 RF Radio Controlled Solar Aviation Light Section 3 Operating the lights using the ALS 2 4GHz Handheld Controller Note Some menu options may not appear if they were not enabled in the Radio Control System set up menu and programmed in to the light 1 2 Fold out the aerial on the top of the ALS 2 4 GHz handheld Controller Turn on the ALS 2 4G
27. e com au technical solar_chart php Important Note the AV425 is a solar powered light fixture It is the operator s responsibility to ensure usage demand does not exceed the charging capacity of the light fixture Avlite holds no responsibility for product failure due to excessive usage demand Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Simple Approach Lighting The AV 425 RF REIL W can be configured into a simple approach lighting system A simple approach lighting system is a lighting system intended for a non instrument or a non precision approach runway This is done through selecting different sync delay or sync offset All lights must be in the same light group and the same REIL group Sync option must be activated in the system menu Flash code selected must be the same Each individual light is then set with a sync delay or sync offset Please refer to Radio Control System Setup Section 2 Programming the light using the cable interface and handheld controller paragraph G or H on Sync offset and Sync Delay for information on how to set Sync Offset or Sync delay di The information contained in this publication is advisory only Please contact your local authority for rules and regulations particular to your region Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled
28. een used or handled other than in accordance with the instructions in the owner s manual and any other information or instructions provided to the customer by Avlite b the product has been deliberately abused or misused damaged by accident or neglect or in being transported or c the defect is due to the product being repaired or tampered with by anyone other than Avlite or authorised Avlite repair personnel 3 The customer must give Avlite Systems notice of any defect with the product within 30 days of the customer becoming aware of the defect 4 Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced Typical battery replacement period is 3 4 years Long term exposure to high temperatures will shorten the battery life Batteries used or stored in a manner inconsistent with the manufacturer s specifications and instructions shall not be covered by this warranty 5 No modifications to the original specifications determined by Avlite shall be made without written approval of Avlite Systems 6 Avlite lights can be fitted with 3rd party power supplies and accessories but are covered by the 3rd Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light party warranty terms and conditions 7 The product must be packed and returned to Avlite Systems by the customer at his or her sole expense Avlite Systems will pay
29. em Setup Page 12 Using the Radio Control to Activate the Airfield Lighting System ALS Page 20 m Page 22 Solar Calculation amp Operating Capabilities Page 25 Simple Approach 26 Runway End Identifier Light REIL Page 28 Maintenance and Servicing Page 30 Trouble Shooting nennen Page 35 Documentation eia Lore iaia Pd dp Page 37 AV SB 10 Solar Booster Page 38 Solar Booster Installation Procedure Page 40 Avlite Light Warranty e Page 42 Version No Description Date Approved 1 0 Manual Launch October 2010 M Henry 1 1 Spec Update amp Solar Booster November 2010 M Henry 1 2 Addition Reil amp Approach lighting November 2011 M Henry 1 3 Alteration to Installation section May 2012 C Procter 2 0 New Product Code January 2013 J Dore 2 1 Torque setting February 2014 P Rainey 2 2 REIL flash character added March 2015 T Stewart Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light el DD Introduction Co
30. en this option has not been selected and saved Press SEND to save options at each change a Lantern Info This displays the current Light information only there are no adjustable options Type Version Radio Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light b Operation Mode Using the UP and DOWN keys select from the following Always On Dusk till Dawn Standby Press SEND after selection c Advanced Operation Mode if Advanced Operation Mode is enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following Visible LEDS IR NVG LEDS Press SEND after selection d Light Group Using the UP and DOWN keys select from the following 0 15 Select any one of the 0 15 light groups Press SEND after selection e Intensity Using the UP and DOWN keys select from the following Low Medium High Press SEND after selection f Flash Code if Flash Code is enabled during Radio Control System Programming Section 1 Using the UP and DOWN keys select from the following 000 to 1FF A full list of available flash codes is available from Avlite Press SEND after selection g Sync Offset if Synchronisation is enabled during Radio Control System Programming Section 1 Note Sync offsets can be set using an absolute value or a percentage Flash Del
31. es and packaging are removed from the runway Installing the Light Assembly to the Frangible Concrete Mount Mount the base plate to the concrete using 4 x M8 concrete bolts Fit the frangible mounting plate onto the concrete base plate and secure using the M8 x 16 SHCS Level the light mounting plate using a spitit level Fit the AV 425 RF to the light mounting plate using M8 SHCS large flat washers and Nylock nuts For further adjustments on levelling the light see next section on leveling the light ooocop Note After adjustments ensure all nuts and bolts are tightened securely and all tools spares and packaging are removed from the runway Latest products and information available at www avlite com AV 425 RF Radio Controlled Solar Aviation Light Aviite www avlite com xa WSS c a SS NN WT B B B B T T T T T A TTG L 24 CC 8 6l 2 hus S67 070 109 AV 425 RF on Frangible Mount Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Contro
32. ght group REIL Groups A REIL group is the group of lights that will flash in sync together REILS from different REIL groups will not flash in sync together When installing 2 pairs of REILS on the airfield one pair at each end it is advisable to ensure they are in different light groups and different REIL groups The information contained in this publication is advisory only Please contact your local authority for rules and regulations particular to your region Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light 0s W 7 X White r amben runway lights j Roe Rew Reo Re Res sequenced flashing eee ee a e Ba Runway End Identifier Light REIL ic aM C dia CAME CLIO uu threshold and runway endjight units red to departing aircraft and green to landing aircraft Sequenced flashing approach lights Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light o Maintenance and Servicing Designed to be almost maintenance free the AV 425 RF requires minimal attention though the following maintenance and servicing information is provided to help ensure the life of your Avlite Systems product Cleaning Solar Panels occasional cleaning of the solar panels may be required Using a cloth and warm s
33. icators to show light output This colour indication should be aligned with the colour indication on the solar unit to ensure correct alignment Fit the 4 x M6 x 20 SHCS Tighten the SHCS evenly and firmly Recommended torque settings for Fitment of Light Heads to Solar Base units using the 4 Hex Bolts supplied It is recommended that the bolts for holding the light heads to the Solar Base units have a torque setting applied of 3Nm for a satisfactory seal Applying a higher Torque setting is not recommended and may void warranty If in doubt please contact your local Avlite representative Remove all tools nuts and bolts from the runway Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Replacing the Battery The AV 425 RF has an internal battery compartment which provides the user with the ability to change the battery after years of operation 1 Removethe four socket head screws on the top lens assembly and separate the AV 425 RF lens assembly from the body base section 2 Remove 2 4 SHCS amp washers from the top battery bracket 3 Remove the 2 x M5 Nylock nuts and washers from the top battery bracket 4 Separate the light head at the connectors 5 Lift the upper battery bracket out of the AV 425 RF 6 Disconnect the old battery 7T Remove the old battery from the chassis 8 Discard old battery in a safe manner 9 Reconnect
34. information The Sealed Lead Acid batteries inside the lights must always be stored in a fully charged state Always make sure the ON OFF switch is in the OFF position All batteries will discharge over time and the rate of discharge is dependent on temperature If the light is being stored in temperatures greater than 40 C the battery will discharge faster Please check battery regularly and recharge if necessary charge the battery via the external charging port on the base of the unit Only attach the plug with your hand do not use multi grips to attach the plug Turn the ON OFF switch to the ON position and place unit in the sun for 2 4 days The AV 425 RF is fitted with a 12 volt charge port that can be used to charge the battery and test the battery voltage Connect the test lead Avlite Part Number BTL SLA 12v to a multimeter on volts Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Safe Battery Handling Charging and Discharging Always ensure batteries are fully charged when installing new lights The light will be dispatched from the Avlite factory fully charged However if time has elapsed between dispatch and installation battery voltage must be checked Never short circuit or reverse polarity a battery damage to the battery and devise may occur and there is a risk of fire Do not use different types of batteries in the s
35. ing Diode technology as a light source The major advantage of LED s over traditional light sources is well established in that they typically have an operational life in excess of 100 000 hours resulting in substantial savings to maintenance and servicing costs Precision Construction Commitment to investing in the design and construction of injection moulded parts including optic lenses light bases and a range of other components ensures that all Avlite products are of a consistent and superior quality Optical Performance Avlite manufactures a range of aviation LED lenses moulded from multi cavity dies The company has superior in house lens manufacturing capabilities to support outstanding optical performance Award winning Patented Technology Several United States and Australian patent registrations are held on Avlite s range of innovative designs with other regional patents pending in Canada United Kingdom and Europe Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light AV 425 RF Model The robust design of the AV 425 RF self contained light ensures up to 12 years of reliable service with minimal ongoing maintenance Specifically designed to survive the harshest environments the AV 425 RF features seven stage powder coated aluminium top base and internal chassis The corners are made from UV stabilised rubber This method allows the customer
36. led Solar Aviation Light Runway B Only is to be HIGH Intensity with a Timeout of 8 Minutes and Runway A will be I R Low Intensity On Runway A set the light group to O On Runway B set the light group to 1 Turn the Control unit On Use the arrow keys to adjust the operational Mode to Always On Press MENU button to reach Light Group Set the Light Group to 1 Press MENU button to reach LED Intensity Use the arrow keys to adjust the LED Intensity to HIGH Press MENU button to reach Timeout Mode Use the arrow keys to adjust the Timeout Mode to Enabled LOW Press MENU button to reach Timeout Duration Use the arrow keys to adjust the Timeout Duration to 8 Minutes Press SEND button Runway A will not change state Runway B will now be High Intensity After 8 minute Runway will revert back to LOW intensity Press MENU button until you reach Light Group Set the Light Group to 0 Press MENU button once to reach LED Intensity Use the arrow keys to adjust the LED Intensity to LOW Press MENU button to reach Advanced Operation Mode Use the arrow keys to select R NGV LEDs Press SEND button Runway A will be in LOW Intensity IR mode Runway B will not change state Lights on Runway B will still receive and pass on the message intended for Runway A Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light JI io EM kkkk MMI f 5 Installation
37. light using the direct connection See Programming Section 1 Check the radio channel in the light using the direct connection is the same as the controller Turn encryption On and set encryption key in the controller and all the lights Ensure that the light bank selected in the controller is the same as the light bank settings in the lights Enable Advanced operation Mode in the Radio Control System Menu See Programming Section 1 Enable Flash Codes in the Radio Control System Menu See Programming Section 1 Sync delay not avaliable Sync not enabled in the Radio Enable Sync in the radio Control Control System Menu Menu See Programming Section 1 Light will not actvate Battery is flat Recharge Battery or connect light to external power supply Lights will not activate during the Day Light is not switched ON at the master switch Light is set to Dusk till Dawn and it is not dark Switch light on at the Red Master Switch on the panel Cover the light for at least 60 seconds of continuos darkness for the light to activate To activate lights during the day temporarily change the light settings to Always On Important Lights must be turned back to Dusk till Dawn or Standby after required daytime use Light will not activate at Light is in Standby Mode Using the Remote control change night light to the Dusk till Dawn Light is not switched on at the master switch Switch light on at the Red Master Swit
38. lled Solar Aviation Light Levelling the light During Installation every effort should be made to ensure that the light is level when installation is complete The following guide lines will help to ensure that the lights will be installed correctly When installing a stake mount into the ground ensure that the stake is installed straight into the ground and not on an angle When installing a concrete mount plate ensure that the concrete pad is level using a spirit level Check the mounting plate with a spirit level in all directions Fit the frangible coupling and top mounting plate and using a spirit level check that the light mounting plate is level using a spirit level If the mounting assembly can not be levelled to a satisfactory plane then spacers can be used under the 4 mounting points to complete levelling Spacers must be secured Flat penny Washers that can be placed under the 4 mounting points and secured in place by the mounting bolts p One spacer fitted here either side of the two washers Two spacer fitted here Incorrect Installation Correct Installation Important Please ensure that spacers are not just under one mounting point Please fill in spacers under other mounting points Failure to space gaps will result in damage to the base or the mounting plate Latest products and information available at www avlite com Avlite AV 425 RF Radio Controlled Solar Aviation Light www avlite
39. ner s expense to the Avlite Systems factory together with a photocopy of the bill of sale for that product a detailed description of the problem and any information necessary for return shipment Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor Sealite products are subject to certain Australian and worldwide patent applications Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Other Avlite Products Available Helipad Lighting Obstruction Lighting Airfield Markers amp Accessories Typical Applications Temporary amp permanent airfield lighting Remote emergency amp defence airfield lighting Barricade hazard amp perimeter lighting Helipad lighting Obstruction lighting For a complete list of product compliances including ICAO amp FAA please contact Avlite today Area amp Sign Lighting Avlite Systems 11 Industrial Drive 61 Business Park Drive Somerville Vic 3912 Tilton New Hampshire AUSTRALIA 03276 USA t 61 0 3 5977 6128 t 1 603 737 1311 61 0 3 5977 6124 f 1 603 737 1320 e info avlite com w www avlite com A subsidiary of Sealite Pty Ltd www sealite com Latest products and information available at www avlite com
40. ngratulations By choosing to purchase an Avlite light you have become the owner of one of the most advanced solar LED airfield lights in the world Avlite Systems draws on more than 25 years experience in the design and manufacture of navigation aids and particular care has been taken to ensure your light gives years of trouble free service As a commitment to producing the highest quality products for our customers Avlite has been independently certified as complying with the requirements of ISO 9001 2008 quality management system By taking a few moments to browse through this booklet you will become familiar with the versatility of your light and be able to maximise its operating function Please remember to complete the Avlite warranty registration card accompanying your light Technology Avlite Systems is a world class solar lighting systems manufacturer with a proven reputation for rapid innovative and agile technology solutions designed specifically for defense government civil and humanitarian aid operations in the most remote toughest environments Electronics Avlite employs leading in house electronic engineers in the design and development of software and related circuitry All individual electronic components are sourced directly by Avlite procurement staff ensuring that only the highest quality components are used in our products LED Technology All aviation lights use the latest advancements in LED Light Emitt
41. ntroller On Use the arrow keys to adjust the operational Mode to ON Press MENU button once to reach Light Group Set the Light Group to ALL Press SEND button Every radio light within range of the control unit will now turn on pep the Lights to Operate in DUSK till DAWN mode Turn the Control unit On Use the arrow keys to adjust the operational Mode to DUSK till DAWN Press MENU button once to reach Light Group Set the Light Group to ALL Press SEND button Every radio light within range of the control unit will now turn on at night during the day the lights will turn off automatically Runway B Only is to be HIGH Intensity but Runway A will Remain in Current Configuration On Runway A set the light group to 0 follow the instruction in Section 2 in the Radio Control System Setup section of this manual On Runway B set the light group to 1 or any group different to Runway A Turn the Control unit On Use the arrow keys to adjust the operational Mode to Always On Press MENU button to reach Light Group Set the Light Group to 1 Press MENU button to reach LED Intensity Use the arrow keys to adjust the LED Intensity to HIGH Press MENU button to reach Advanced Operation Mode Use the arrow keys to select Visible LEDs Press SEND button Runway A will not change state Runway B will now be High Intensity Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Control
42. oapy water wipe off any foreign matter before rinsing the panels with fresh water Battery Check inspection of batteries should be performed every three years minimum to ensure that the charger battery and ancillary electronics are functioning correctly Using a voltage meter check that the battery voltage is at least 12 volts under 100mA load and ensure all terminals are clear of foreign matter O Ring Check inspect the condition of the o ring for damage wear or if it is brittle and replace if necessary The o ring should be a rubber texture to ensure a complete and even seal Service Tools 1 x M2 Allen Key 1 x M5 Allen Key 1 x 13mm Combination Wrench 1 x M8Allen Key 1 x 10mm Combination Wrench 1 x Silicone Grease Replacement Part Numbers Complete Units AV425 R G AV425 W AV425 W Y Light Head only ALA AV425 R G ALA AV425 W ALA AV425 W Y Solar Unit Only ABA AV425 Test Lead BTL SLA 12v Battery Charger 12 volt BTC SLA 12v Solar Booster AV SB 10 Installing the Light Head Assembly on the Solar Unit After servicing it will be necessary to reinstall the light head on the solar unit jn 2 3 4 m Connect the 4 bullet connectors Ensure the o ring seal on the top of the solar chassis is in place clean and lightly greased Feed the wires into the corner of the solar unit Locate the light head onto the solar unit in the correct orientation to the runway The light head is fitted with reflective tape ind
43. ode is required The solar panel is connected to the light via the external charge port and the panel is mounted at an angle to maximise solar collection during daylight hours The solar Booster will provide up to 0 5Ah of additional charge into the battery In areas of high solar conditions this may allow the fixture to operate in a high intensity L 861 output setting for up to 11hrs per night In lower solar regions fitting the Solar Booster may widen the operating latitudes where the standard AV425 may not be sufficient For detailed solar profiling of your region please contact Avlite Systems Latest products and information available at www avlite com AV 425 RF Radio Controlled Solar Aviation Light Avlite www avlite com SPECIFICATIONS AV SB 10 Electrical Characteristics Voltage v Amperage MA Temperature Range Solar Characteristics Solar Module Type Output watts solar Module Efficiency Charging Regulation Physical Characteristics Body Material Mounting Height mm inches Width mm inches Length mm inches Mass kg lbs Product Life Expectancy Certifications 12 580 40 to 80 C Multicrystalline 10 14 Microprocessor controlled 7 stage powder coated aluminium 4 hole 200mm bolt pattern 150 57 8 370 141 2 560 22 3 2 7 Up to 12 years CE EN61000 6 3 1997 EN61000 6 1 1997 Quality Assurance ISO9001 2008 Waterproof IP68 Intellectual
44. ow Amber Blue Sectored Combinations IR Peak Intensity temporary high Steady on Red 25 0 Green 370 0 White 275 0 Yellow 92 5 cd t Horizontal Output degrees As per L861 and L861E Vertical Divergence degrees As per L861 and L861E Available Flash Characteristics gt 250 including steady on user adjustable including Morse Code and RF sequenced amp synchronised flashing Intensity Adjustments FAA Low 10 Medium 30 High 100 ICAO Low 20 Medium 40 High 100 LED Life Expectancy hours gt 100 000 Electrical Characteristics Circuit Protection Integrated Operating Voltage V 12 Temperature Range 40 to 80 C Solar Characteristics Solar Module Type Multicrystalline Output watts 18 solar Module Efficiency 14 Charging Regulation Microprocessor controlled Power Supply Battery Type SLA Sealed Lead Acid Battery Capacity Ah 24 Nominal Voltage V 12 Autonomy FAA Optic hours Steady on Low intensity 320 hours Medium intensity 130 hours High intensity gt 50 hours Autonomy ICAO Optic hours Steady on Low intensity 170 hours Medium intensity 2110 hours High intensity gt 60 hours Radio Controlled Frequency 2 4GHz ISM Band Range Up to 1 4km relayed Expandability AvMesh Compliance Physical Characteristics Body Material 7 stage powder coated aluminium Lens Material LEXAN Polycarbonate UV stabilized Lens Diameter mm inches 155 6
45. s applicable in the country of manufacture the liability of Avlite Systems under this Warranty will be at the option of Avlite Systems limited to either the replacement or repair of any defective product covered by this Warranty Avlite Systems will not be liable to Buyer for consequential damages resulting from any defect or deficiencies in accepted items Limited to Original Purchaser This Warranty is for the sole benefit of the original purchaser of the covered product and shall not extend to any subsequent purchaser of the product Miscellaneous Apart from the specific warranties provided under this warranty all other express or implied warranties relating to the above product is hereby excluded to the fullest extent allowable under law The warranty does not extend to any lost profits loss of good will or any indirect incidental or consequential costs or damages or losses incurred by the purchaser as a result of any defect with the covered product Warrantor Avlite Systems has authorised distribution in many countries of the world In each country the authorised importing distributor has accepted the responsibility for warranty of products sold by distributor Warranty service should normally be obtained from the importing distributor from whom you purchased your product In the event of service required beyond the capability of the importer Avlite Systems will fulfil the conditions of the warranty Such product must be returned at the ow
46. shing Disabled I Diagnostic For the following diagnostic tests to following diagnostic flash results can be displayed for the light Diagnostic Pass 1x1 second flash AS J L A 1 Second 1 Second 1 Second Diagnostic Fail 2 x 300 milli second flashes 1 Second 300 ms 400ms 300 ms 1 Second Using the UP and DOWN keys select from the following Node Sub Net Pass Confirms light is a node on the Sub Network Node Main Net Pass Confirms light is a node on the Main Network External Power Pass Confirms external power is connected via HVPS Battery Flat Pass Confirms battery voltage is under 10 5 Volts Battery Low Pass Confirms battery voltage is between 10 5 and 12 5 Volts Battery Healthy Pass Confirms battery voltage is over 12 5 Volts Press Send to receive a diagnostic flash sequence When the controller is in operation mode multiple changes can be set and sent at the same time It is not necessary to press send after each change Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Using the Radio Control to Activate the Airfield Lighting System ALS The Radio Controller is very easy to use and by reading through the How To section below all of the advanced features will be well within your grasp Make sure that all the lights in the same Light Group Turn All the Lights ON Turn the Radio Co
47. tensity is set to medium intensity c High LED intensity is set to high intensity Note this menu will not be enabled if the selected operational mode is STANDBY Timeout Mode This menu is used to setup the LED high intensity timeout feature found in each light Light will revert from high intensity to low intensity after a programmable duration The options include Enabled LOW Disable a Enabled LOW The immediate LED intensity is selected via the LED Intensity menu after Timer Duration the LED Intensity will revert back to the LOW setting b Disable The high intensity LED timeout is disabled The LED intensity will be selected via the LED intensity menu Note this menu will not be enabled if the selected operational mode is STANDBY Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light Timeout Duration This menu is only visible when the timeout Mode is enabled This menu is used to select the timeout duration the time before the LED intensity reverts back to its LOW intensity state The timeout duration can be set from 1 minute to 60 minutes Diagnostic This feature can be used to check the battery voltage in every light in the airfield The command can be sent any time and it will not affect the current state of the light If the light is in STANDBY mode the light will flash as shown below and revert to STANDBY mode after the diagnostic has
48. the solar unit Remove the 4 socket head cap screws and remove the light head from the solar unit enough to access the programming port The light needs to remain connected the solar unit Remove the blue waterproof cap from the programming port Programming Port Replace blue cap after programming Connect the programming cable to the light head Connect the programming cable to the programming charging port located on the left hand side of the ALS2 4GHz handheld radio controller Turn on the controller at the Red Master switch located on the right hand side of the ALS 2 4 GHz handheld radio controller Latest products and information available at www avlite com Avlite AV 425 RF www avlite com Radio Controlled Solar Aviation Light 7 Turn on the light at the red master switch on the solar chassis 8 Unitis ready to receive programming signals Note Light head needs to be connected to the solar chassis during programming to be able to recieve power enabling it to be programmed 9 Press and hold the MENU button for 3 Seconds The screen will display the following message 10 Using the menu key scroll down the submenu to CONNECTION METHOD 11 Using the UP and Down keys select DIRECT CONNECTION 12 Press SEND 13 This Menu contains the following Sub Menu Press MENU to scroll through the menu Note In this menu the programmed option will be indicated by if the option is indicated by an X th
Download Pdf Manuals
Related Search