Panther Series - CA Technologies
Contents
1. 4 Fan width can be adjusted using the fan control knob Turning the knob clockwise narrows the fan Maintenance IMPORTANT Routine cleaning and maintenance is essential to insure proper gun operation Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner 1 If a gun cleaner is being used connect and clean the gun in the gun cleaner according to the manufactures instructions 2 If a gun cleaner is not being used For pressure setups remove air cap and clean separately using clean solvent Connect a pressurized solvent supply to the fluid inlet trigger the gun allowing solvent to flow thru the gun until clean For siphon setups first clean the siphon cup thoroughly then spray clean solvent thru the gun until clean NOTE Gun head disassembly is not recommended for normal cleaning and maintenance Items 29 30 31 and 32 replace items 1 2 3 and 13 for model P100G water based setup Gun head disassembly and reassembly instructions Gun head disassembly To remove the nozzle carrier 5 and air cap adapter 6 1 Remove the air cap 1 fluid nozzle tip 2 fluid nozzle body 3 and needle 13 2 Remove the needle seal cartridge 23 3 Loosen the locknut 9 and remove fluid inlet 10 using a 5 8 open end wrench 4 The nozzle carrier and air cap adapter will now slide forward from the gun body 11 Gun head reassembly 1 Install a new o ring 7 on the air cap adapter2. Install the thread locknut 9 onto the fluid inlet as far as possible Slide the nozzle carrier 5 into air cap adapter 6 and insert into the gun body as far as possible Be sure the nozzle carrier extends into the hole at the back of the gun head Install the needle seal 23 but do not tighten Rotate the nozzle carrier until the fluid inlet port in the nozzle carrier is aligned with the threaded hole in the body While in this position insert the fluid inlet 10 and tighten firmly Tighten the needle seal 23 to approx 12 ft Ib torque Tighten the fluid inlet 10 to approx 25 ft Ib torque Tighten the locknut 9 to approx 33 ft Ib torque P100G Water Based 8 face Panther vode Ar apa e ja j E e Indicates part included in repari kit 10 108 amp 10 110 Note Items 29 30 31 32 and replace items 1 2 3 and 13 for the model P100G 1590 w ater based setup See Air Cap Chart Fluid Needle Fluid Control Knob Spring Seat Revised 1 18 13
3. C A Technologies Panther Series lt TEFLON COATED SPRAY GUN PRODUCT INFORMATION PATENTED Corrosion Control P100H P200C Glue P100G P100G Water Base AIR CAP AND FLUID NOZZLE CHART MODEL NO aircaps rCaP Fan SUGGESTED GUNINLETPRESS AVAILABLE FLUID NOZZLES NEEBLES Ring Control marking on needle 2031 0214 1 4mm 055 2031 0215 1 5mm 059 40 1100 1 21 1095T 21 1001 60 1502 30016 1 6mm 063 0 1100 100 31 0217 1 7mm 070 21 2266T L A 11 21 2266 37 Included 60 so s 31 0618 1 8mm 070 40 1115 115 as 1590 08 31 1593 08 tr 022 40 1508 ELAM luded 60 1500 2 32 0618 1 8mm ony 40 1218 218 P200C 2220527 Included 60 1500 32 0622 2 2mm 086 40 1222 222 32 0628 2 8mm 110 40 1228 228 22 2062 ga eo t500 m oe 2118Z 1 8mm 0707 40 1218 218 ere 5d 32 2122Z 2 2mm 086 40 1222 222 32 2128Z RE 40 1228 228 Coating Atomization Technologies P O Box 17820 Boulder CO 80308 888 820 4498 Fax 303 438 5708 www sprayCAT com Operation and Maintenance Instructions for Panther Spray Guns Operation 1 Connect air supply hose at handle of gun 2 Connect a pressurized fluid supply or paint siphon cup to the gun fluid inlet 3 Fluid flow can be controlled using the fluid control knob this restricts flow by limiting needle travel It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to fine tune flow rate
Download Pdf Manuals
Related Search