SERVICE MANUAL - X-Core Technology Co., Ltd.
Contents
1. Do not let the vertical angle exceed 20 Figure 1 E For capturing the back plate no The vertical angle must not exceed 30 Figure 2 E Capture zone distance Between 15 20 meters from the camera Figure 2 T 15 20M gt 3 Adjust the zoom of the vari focal lens The picture width should not exceed 1 5 traffic lanes at the capture zone gt Enter SETUP menu and select DC under LENS options 4 In order to ensure a clear image under different light conditions adjust the settings once during the daytime and once during the nighttime is recommended to achieve optimal results E Daytime setting Adjust the lens focus to see a clear image both at the center and the upper down edges of the monitor If the image on the monitor is too bright adjust the shutter speed accordingly gt Enter EXPOSURE sub menu under SETUP menu and select SHUTTER gt Select shutter speed according to the speed of vehicle 1 2000 1 10000 1 10000 Suggested Shutter Speed gt When speed of vehicle is less than 50km 1 250 sec gt When speed of vehicle is less than 100km 1 500 sec gt When speed of vehicle is more than 100km 1 2000 sec E Nighttime setting Adjust the lens focus to see a clear image at the upper down edges of the monitor means focus at the center According to the environment adjust AGC value to heighten the brightness signal when necessary gt Enter EXPOSURE sub menu under SETUP menu a2. Light Compensation HLC Highlight Compensation Auto DPC Dead Pixel Compensation Wide Dynamic Range Highlight Compensation jaf i i E hs 3 A J m 2 E Parts Names amp Components Hex Screwdriver Hole to fix lens Auto Iris Plug Manual SERVICE MANUAL TI SONY DSF COLOR CCO CAMERA Em WIA DC DRIVE Pin 1 Red Drive Drive No 3 Pin No 1 Pin Lens cable Damp J Connector Damp Installation Instructions 1 Remove the cap from the lens mount 2 Select the C mount lens with mount ring or CS mount lens 3 Screw and fasten the lens into the lens mount 4 Connect the video output wire between monitor and camera through 75ohm type coaxial cable 5 Connect the power cord input 6 When monitor shows the picture please adjust the focus and iris of the lens to obtain the best image according to the following procedures e Choose objects at a distance about 5 10 meter away Loosen the mount lens fixing screw use L wrench if necessary Turn the lens and the mount together until image is clear Screw the mount to camera 7 Fix camera to the bracket 1f necessary Switch Definition UP button LEFT SET RIGHT button button button DOWN button SET button Press to display the menu In the menu this button functions as ENTER UP amp DOWN buttons Press to select the item of menu LEFT amp RIGHT buttons Pre
3. generated from above devices will distort the video image 3 Place this camera on a solid base Install the camera away from stoves or other heat generating devices as the high temperature could cause deformation discoloration or other damages to the camera Install the camera at where the temperature range does not exceed 10 C to 50 C 14 F to 122 F 4 Do not expose and operate the camera in the rain and humid areas 5 Use only soft dry cloth to clean the camera Also use lens tissue or cotton tipped applicator and ethanol to clean the CCD sensor and camera lens 6 When the camera is not in use put the cover cap on the lens mount Please do not touch the surface of CCD by bare hand Introduction This OSD series CCD camera introduces a new level of high picture quality through the digital signal processing LSI s technology for advanced video surveillance It provides the most reliable and accurate color picture in the security industries Main Features Color camera with SONY 1 3 Super HAD II CCD sensor Employs Digital Signal Processor DSP chip set for image control Ultra high resolution 600TVL B W 650TVL High sensitivity CCD enables a clear image even in 0 01 Lux Controlled by OSD On Screen Display menu Programmable AE AWB GAMMA processing 2DNR 2D Noise Reduction digital WDR Wide Dynamic Range Motion detection mirror privacy mask Parking line guide display lens shading correction BLC Back
4. light environment higher AGC more noise e ON To enable this function e OFF To disable this function gt MIRROR gt ON To see mirror image on monitor screen e OFF To disable this function gt FONT COLOR FONT color O 15 ID amp TITLE O 15 adjustable gt CONTRAST Value 0 255 adjustable gt SHARPNESS Value 0 255 adjustable gt DISPLAY e CRT PED LEVEL 0 63 COLOR GAIN 0 255 adjustable LCD GAMMA 0 05 1 00 PED LEVEL 0 63 COLOR GAIN 0 255 adjustable e USER GAMMA 0 05 1 00 PED LEVEL 0 63 COLOR GAIN 0 255 adjustable gt NEG IMAGE Negative Image gt ON To show negative image on monitor screen gt OFF To disable this function LANGUAGE Supports ENGLISH Simple Chinese VERSION To show the version of this camera RESET Select for factory reset Specification MODEL OSD WDR OSD WDR with ICR True DAY amp NIGHT IR OPTICAL FILTER Built in anti aliasing R cut filter Built in anti aliasing R pass 850nm filter PICK UP DEVICE Sony 1 3 Super HAD II High Resolution CCD EFFECTIVE PICTURE NTSC 768 494 ELEMENTS H V PAL 752 582 AUTO IRIS DC Drive Auto Iris Lens AUTO ELECTRONIC NTSC 1 60s 1 100 000s AES ON 1 60s AES OFF SHUTTER PAL 1 50s 1 110 000s AES ON 1 50s AES OFF 10 C 50 C 14 F 122 F LENS MANUAL DC VIDEO EXPOSURE gt SHUTTER AUTO FLK 1 50 1 250 1 500 1 1000 1 2000 1 4000 1 5000 1 10000 1 100000 g
5. SERVICE MANUAL 1 3 SONY DSP COLOR CCD CAMERA 600TVL O S D WDR SERIES The serial number of this product may be found on the bottom of the unit You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft Model No Serial No V 4B_W_M CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is interned to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important Operating and maintenance servicing instructions in the literature accompanying the appliance A Before attempting to connect this product please read and keep this manual for future use Safety Warning 1 Do not open the cover it may cause electric shock Ask a qualified service person for maintenance when you encounter any problems 2 Install the camera away from TV radio transmitter magnet electric motor transformer audio speakers because the magnetic fields
6. ge of the background as well as the object gt ON To enable this function Value 0 63 adjustable gt OFF To disable this function w WHITE BAL White Balance ATWI Auto Tracking White Balance The white balance will adjust continually according to the color temperature of the object The range of color temperature is 2 000 K 9 500 K e ATW2 Auto Tracking White Balance The white balance will adjust continually according to the color temperature of the object The range of color temperature is 2 000 K 10 500 K e AWCSET Auto White Balance Control Push to set white balance according to the color temperature of the background e MANUAL The manual adjustment mode enables finer adjustment of ATW Set the color temperature to MANUAL and then increase or decrease the RED 0 255 and BLUE 0 255 color values while monitoring the color changes on the object Or chose the INDOOR OUTDOOR mode for quick adjustment w BACKLIGHT When there is strong backlight behind the object enable this function to achieve a clear image of the background as well as the object e BLC Back Light Compensation AREA1 AREA2 adjustable HLC Hightlight Compensation ALL DAY NIGHT ONLY adjustable gt OFF To disable this function w DAY amp NIGHT e COLOR Common mode e AUTO Automatically changes between color mode under bright light environment and B W mode under low light environment Set the value of D N LEVEL Day to Night 0 216 N D LEVEL Nig
7. ht to Day 0 206 D N DELAY Day to Night 1 30 SEC N D DELAY Night to Day 1 30 SEC to define the changing condition and time B W Stay in B W mode for clear and better visibility image under low light environment BURST ON OFF IR SMART ON OFF IR LEVEL HIGH LOW adjustable EXT Control day amp night mode by external device if connected amp DPC Dead Pixel Correction Cover the lens then press SET button to delete dead pixel on screen SPECIAL MENU sy CAM TITLE Camera Title ON To name the camera title e OFF Not active 7 MOTION Motion Detection When the object on screen is moving the camera will detect the changes and display a warning on screen gt ON AREA1 AREA4 adjustable 0 255 DEGREE adjustable e OFF Not active cy cy cy cy cy cy PRIVACY Privacy Zone Cover the areas you do not wish to appear on screen gt ON AREA1 AREA8 adjustable 0 15 COLOR adjustable gt OFF To disable this function PARK LINE Parking Line gt ON Parking line guide display on screen gt OFF To disable this function IMAGE ADJ gt LENS SHAD Lens Shading Compensation gt ON Counter lens shading on the four corners of monitor screen gt OFF To disable this function gt 2DNR 2D Noise Reduction Enable this function to reduce the noise at low light environment This function enables the camera to use a higher AGC level to electronically enhance the sensitivity of the camera in low
8. nd select AGC gt AGC LOW MIDDLE HIGH adjustable 5 If the image is smeared and the license plate number is not captured clearly E When the camera is connected directly to the monitor Adjust the shutter speed until the image is clear E When the camera is connected to a DVR system If you get a smeared image during playback the reason is the performance of VGA card in the DVR is not sufficient V 4B_W_M
9. ss to change the item value Menu Operation Press the SET button to display the menu on screen Press the UP or DOWN button to select the item The selected item will be highlighted Press the LEFT or RIGHT button to change mode The ENTER symbol lt 1 means there is a sub menu Press the SET button to enter to the sub menu Select the EXIT item and press the SET button to finish setting SETUP MENU w LENS To select the lens mode depending on the lens used e MANUAL When manual iris lens is used DC When auto iris lens that requires a DC drive signal is used VIDEO Not available EXPOSURE gt SHUTTER To change the shutter setting and speed based on the environment AUTO After an immobile brightness value is set the shutter speed will adjust automatically to achieve the value e FLK Select when flickering occurs on the screen due to an Imbalance between illumination and frequency Under this mode the shutter speed is NTSC 1 100 PAL 1 120 e Fixed speed adjustable 1 50 1 250 1 500 1 1000 1 2000 1 4000 1 5000 1 10000 1 100000 gt BRIGHTNESS Value 0 255 adjustable gt AGC Auto Gain Control Enable this function to heighten the brightness signal automatically HIGH LOW MIDDLE adjustable e OFF To disable this function gt DWDR Digital Wide Dynamic Range When there is a very strong backlight behind the object more than the AGC function can handle enable this function to achieve a clear ima
10. t BRIGHTNESS 0 255 gt AGC LOW MIDDLE HIGH OFF SETUP MENU gt DWDR ON 0 63 OFF WHITE BAL ATW1 ATW2 AWCDSET MANUAL RED 0 255 BLUE 0 255 INDOOR OUTDOOR BACKLIGHT BLC AREA1 AREA2 HLC ALL DAY NIGHT ONLY OFF DAY amp NIGHT COLOR AUTO B W EXT DPC RESET CAM TITLE ON OFF MOTION ON AREAI AREA4 DEGREE 0 255 OFF PRIVACY ON AREA1 AREA8 COLOR 0 15 OFF PARK LINE ON OFF IMAGE ADJ gt LENS SHAD ON OFF gt 2DNR ON OFF gt MIRROR ON OFF SPECIAL MENU gt FONT FONT 0 15 ID amp TITLE 0 15 gt CONTRAST 0 255 gt SHARPNESS 0 255 gt DISPLAY CRT PED LEVEL 0 63 COLOR GAIN 0 255 LCD GAMMA 0 05 1 00 PED LEVEL 0 63 COLOR GAIN 0 255 USER GAMMA 0 05 1 00 PED LEVEL 0 63 COLOR GAIN 0 255 gt NEG IMAGE ON OFF LANGUAGE ENGLISH S CHINESE VERSION V 4B_W_M Appendix Installation Manual for Special Application License Plate Recognition 1 A5 55mm or other more than 10X suitable vari focal auto iris lens is recommended Connect regulated DC12V power supply to the power input at the rear panel of camera Connect BNC video cable to the video output at the rear panel of camera 2 Fix the camera on the bracket Adjust the viewing angle of camera according to the below recommendations E For capturing the front plate no Setting the camera at a 15 or less vertical angle will achieve the best performance
Download Pdf Manuals
Related Search