rev 200rG KIT-AA rev 200rG KIT-AA
Contents
1. 2 Your Hogtunes system is designed specifically for a motorcycle at speed Exhaust noise and wind noise have been taken into careful consideration in how your system performs How your new system sounds in a driveway or garage is radically different from how it will sound at highway speeds Although your system was set up with a factory radio with its bass and treble controls in the middle position if you feel the need to make adjustments please do so carefully at your normal cruising speed 3 If you have an aftermarket car radio on your bike everything will work fine Please remember that car radios are designed to work in an envi ronment with little or no exhaust or wind noise Many car radios have features such as equalizers loudness contours surround effects etc all designed for a quiet environment and all of which will hurt your ability to hear your motorcycle system at speed if left on Please take a minute and turn as much of these features off With a car radio in your bike the only adjustments you should be able to access for best performance are volume bass treble balance and fader 4 If you re using an external device to supply music through the radios AUX port we have an article on our website that can help make your peripheral audio device sound as good as it can The article is at http www hogtunes com techzone_files Level_matching pdf TECHNICAL SPECIFICATIONS Hogtunes2. warranty void stickers 7 Damage due to water from custom installations 8 Damage from incorrect installation improper use abuse or modifications 9 Damage to inbound product due to improper packing Harley Davidson Electra Glide Road Glide Street Glide Ultra Classic Tri Glide CVO Screamin Eagle and Tour Pak are Trademarks and or Registered Trademarks of Harley Davidson Inc Milwaukee Wisconsin USA and if Used or Implied are for Reference Only There is No Affiliation Between Harley Davidson Inc and Hogtunes Inc 11 Hogtunes products will play much louder than the Original Equipment which can be a distraction to the rider and or passenger Please use caution when adjusting or playing your stereo at high volume especially in traffic You are a valued customer so please Ride Alert Arrive Alive www hogtunes com
3. REV 200 AA Amplifier RMS Power at 2 Ohms 0 5 100 watts x 2 Freq Response csceeeeeeeeerees 30hz 25khz PUSe GLAM wcaiiiaseee seieseisvacises 30 amp Hogtunes 3572 AA Front Speakers Power Handling oseese 100 RMS 150 Peak Frequency Response 55hz 25Khz DE MSUIVIIVG ereen 92 db 1watt 1meter Nominal Impedance 0 2 0 Ohms COOMFGClOns sirosis teosena EXTREME WARRANTY INFORMATION Please Record Your Amplifier s Serial Here Hogtunes speakers are warranted for a period of 20 years The REV 200 AA Amplifier is warranted for 3 years from original purchase date Proof of purchase is required for all warranty claims The warranty applies to the original retail customer and is not transferable Please contact Hogtunes for all warranty claims Products found to be defective during the warranty period will be repaired or replaced with a product deemed to be equivalent at Hogtunes sole discretion Hogtunes complete warranty policy is available on our website at www hogtunes com warranty html What Is Not Covered 1 Any expense related to the removal or re installation of Hogtunes products 2 Repairs to these products performed by anyone other than Hogtunes 3 Subsequent damage to any other components A Any product purchased from a non authorized Hogtunes dealer 5 Damage to Hogtunes products due to an accident or collision 6 Hogtunes Amplifiers with broken or removed
4. front of the tank console for wires to pass Secure the amplifiers harness to the bikes factory harness using zip ties Step 6 Attach the red wire to the positive battery terminal and the black wire to the negative battery terminal The factory battery wires are also re installed at this point Secure the amplifiers wire harness to the bike s factory harness along the frame and behind the tank using supplied zip ties Please run the power harness as per the manual Sometimes people assume they know more than us and wire amplifier power to the headlight wires or other places Not only will your friends laugh at you but you will be calling us for technical support Please save us all from the grief and phone call Step 7 Turn the bikes ignition to the ACC position and turn the radio on at low volume making sure the system is working Using supplied zip ties clean up the wiring inside the fairing You will see a large wire harness right under the back of the radio that sits just behind the hooks that the outer fairing clips onto You should zip tie any Hogtunes wire to this main harness so that no wires are in the way of these hooks Otherwise the outer fairing will not go on and like Step 1 in this manual expletives will be kept to a minimum 5 AMPLIFIER WIRING DIAGRAM f Yellow black from Green Black from amp amp plugs into plugs into BRAKE SIDE CLUTCH SIDE factory factory speaker wires speake
5. Audio Solutions For The Great American Cruiser REV 200RGKIT AA High Performance Front Speaker and Amplifier Kit FOR USE ON 1998 2013 ROAD GLIDE MODEL BIKES WITH FACTORY RADIOS INSTALLATION MANUAL READ ENTIRE MANUAL BEFORE STARTING INSTALLATION Damage To Inner Fairing WILL Occur If Factory Screws Are Used To Attach New Speaker Grills To Your Bike Hogtunes Assumes ZERO Responsibility For This The Correct Screws Are Provided In This Kit Thank you for choosing the Hogtunes REV 200RG Kit AA for 1998 2013 Road Glide Model Bikes Since positive word of mouth is the best way to grow our business we want your new system to work as well as it was designed to If you have any questions or concerns we are here to help The REV 200 AA Amplifier is a Class D design We chose this design because it yields plenty of power is easy on the bikes charging system and produces little heat It should be understood that ALL Class D amplifiers may cause a reduction in FM reception Nothing is affected when playing CD MP3 Satellite radio or any other music device FM reception will differ and depend on the condition and type of antenna that you are using and although every effort has been made to minimize any loss we strongly advise against the use of in fairing or hidden antennas with Class D amplifiers for best FM reception To help protect your bike s electrical system and battery the amp has a built in feature where it will turn itsel
6. TE To mount the 2nd REV 200 AA the Hogtunes RG 40 4 Adaptor plate is required Use supplied blue plug to send signal from expansion port of first amp to input of second amp OGHUNES SGRUNES x Optional HF 2 Tweeter Pod SYSTEM UPGRADE 3 f This system uses an NCA 450 AA 200 watt 4 channel amplifier as well as our REV 200 AA 200 watt 2 channel amplifier for the Ultimate in real power As shown below a typical system would have the 4 channel amp power the fronts and tweeter pod if present and rears The bypass out of the 4 channel sends music to the REV 200 AA which then powers 6 x9 saddlebag speaker lids or 7 fairing lower woofers If you don t have a tour pak you can also do a similar system with fronts speakers and tweeter pod fairing lower woofers and 6 x9 saddlebag lids The beauty of either system is that it can all be done in stages It is 100 bolt in and 100 plug and play Use supplied blue plug to send signal from expansion port of first amp to input of second amp OGTUNES HOGTUNES Optional HF 2 Tweeter Pod ADJUSTING YOUR SYSTEM PLEASE READ A In order to make your new system perform as good as it was designed please take a minute to understand and follow these tips 1 Set your Automatic Volume Control AVC to 3 bars After extensive on road testing we found that this AVC position works and sounds best Your new amplifier has been specifically set up for this radio setting
7. ck connector This plug sends amplified power to your speakers Locate the 4 pin black plug wire harness with brown black and blue black wires Plug it into the amplified output plug The blue black wires will plug directly to the speaker on the brake side of the bike The brown black wires will plug directly to the speaker on the clutch side of the bike Step 4 The orange wire is the remote turn on lead and tells the amp to turn on whenever it sees 12v 5 amp min Unplug the factory orange center wire on the cigarette lighter Plug the orange lead from the amplifier directly onto the lighter using the female connector Plug the factory lighter wire to the male take off connector which is part of the amp s orange turn on lead Step 5 On the brake side of the bike in front of the gas tank on the side of the frames backbone you will see a rectangular opening where a large wire harness and throttle idle cables on 98 07 bikes pass through from the fairing side of the bike The red and black wires for the amp will pass from the fairing side through the large opening under the radio and through the rectangular opening HINT Fishing a small piece of wire through this opening first taping the red and black wires to the fish and then using the fish to feed the wires through may reduce install time Loosen the tank console and run wires up and over the gas tank but under the tank console There is a provi sion on the
8. f off if it sees less than 10 5 volts whether the bike is running or not If you re listening to your stereo while not riding this feature can help protect your battery so the bike can still start If you re riding and the amp shuts off this could be showing a potential issue with your charging system If this feature is activated and the amp shuts off it will turn the amp back on again if the voltage exceeds the 10 5 volt threshold A video version of this manual is available at www hogtunes com If you still need assistance please consider a professional installation by your motorcycle dealer Hogtunes Contact Information Email tech hogtunes com Tel 705 719 6361 2 INSTALLATION INSTRUCTIONS 7 Step 1 Step 2 Step 3 Step 4 Remove the seat and both wires and from the battery Remove the outer fairing headlamp assembly and set it aside Refer to a service manual if you need help with this NOTE A towel on the front fender can help prevent scratches or dings from dropped tools or fasteners etc Expletives will also be kept to a minimum On the brake side inside of the of the inner fairing you will see a wire strap that secures a 3 wire harness black blue and brown to the bike Take the wire out of this strap and let it hang The A arrow in Figure 1 1 is where a larger factory Molex plug is secured to the bike if present Pull down on this Molex to unclip it from the
9. frame and let it hang for now NOTE Newer model bikes have this Molex located elsewhere Using a small flat head screwdriver locate and adjust the 3 position switch on the end of the amplifier to the 3 position The B and C arrows in Figure 1 1 show the nuts that need to be removed on the brake side of the bike so the steel plate and amp can be mounted using these 2 main studs Once the plate is on re install these nuts to factory Figure 1 1 torque specifications The Molex Amplifier correctly that was removed from the frame positioned on bike arrow A can be re secured to other wire harnesses using supplied zip ties if Molex is present Unplug the factory wires at each front speaker Locate and remove the 3 torx head screws and single speed nut that holds each speaker grill to the bike The speakers and grills will come away from the inner fairing as one unit Step 5 Step 6 Separate the Hogtunes speakers from their grills If you want to use the supplied steel mesh grills continue to Step 6 If you want to keep the stock grill cloth look take your stock grills and CAREFULLY separate the factory plastic mesh that holds the grill cloth from the main grill ring Carefully remove the Hogtunes steel mesh from the Hogtunes ring Your factory mesh grill cloth should have enough tack to stick onto the Hogtunes ring but will be properly secured when the grills are i
10. nstalled Included in this kit is a bag with six Phillips head screws Using these supplied screws install each 3572 AA grill to the bike and re install the stock speed nut on each side Re attach the 5x7 s to their grills using the screws you took out in Step 5 noting that the speakers must be oriented in the grills so the wire connectors are closest to the radio DO NOT USE FACTORY SCREWS TO ATTACH NEW GRILLS TO FAIRING WIRING THE AMPLIFIER A Step 1 Step 2 Step 3 Plug the two connectors of the main wire harness into Power and Audio Input on the amplifier Tighten snug the two small flathead screws on the power connector to prevent it from backing out while riding On the input harness locate the yellow black pair of wires with the male connectors and plug them into the factory speaker wires on the clutch side of the bike Also on the input harness locate the green black pair of wires with the male connectors and plug them into the factory speaker wires on the brake side of the bike The connectors are sized correctly and will only go in one way NOTE The blue 4 pin plug with black wires on the input harness is an expansion port which is used to send music to a second amp or is used to send radio power to run other speakers on the bike You can see how the expansion port can be used further on in this manual On the opposite side of the amp are 3 75mm wires ending with a A pin bla
11. r wires Orange wire goes to center pin on cigarette lighter Power and ground DIRECT to battery Brown Black Blue Black wires from amp wires from plug into Clutch amp plug into side speaker Brake side speaker AMPLIFIER WIRE COLOR CODES Yellow Black Clutch Side Amplifier Input From Factory Radio Brown Black Clutch Side Radio Output to Front Speaker Green Black Brake Side Amplifier Input From Factory Radio Blue Black Brake Side Radio Output to Front Speaker Orange Remote Turn On Lead Red 12v Positive Attaches Directly to Battery Post Black 12v Negative Attaches Directly to Battery Post SYSTEM UPGRADE 1 This system is an easy way to add rear speakers to your bike if you ve added a King Tour Pak Hogtunes rear speaker pods come with a wire harness set up for quick detach tour paks that will plug right into the expansion port on the amp IMPORTANT Since the RADIO power will be used to power the rear speakers you must use rear speakers specific to your year of bike Use expansion port to send radio s built in power to a second set of speakers rears on Non Ultra Models Optional HF 2 Tweeter Pod SYSTEM UPGRADE 2 A This system has the incredible power of two 2 REV 200 AA Amplifiers The amp that came in this kit will power the 5x7 fairing speakers while the second amp will bolt in and can be used to power OUR 6x9 saddle bag speaker lids or fairing lower woofers NO
Download Pdf Manuals
Related Search