Operation and Service Manual
Contents
1. A9302002 Figure 2 3 Grounded DUT Measurement Packaging the Adapter If shipment to a Agilent Technologies service center is required each adapter should be repackaged using the original factory packaging materials Alteratively comparable packaging materials may be used Wrap the adapter in heavy paper and pack in anti static plastic packing material Use sufficient shock absorbing material on all sides of the 16117C to provide a thick firm cushion and to prevent movement Seal the shipping container securely and mark it FRAGILE 2 4 Preparation for Use Operation Introduction This chapter describes the features of the 16117C see Figure 3 1 and the connection to the 4339B and DUT AQ303001 Figure 3 1 Adapter Features 1 BNC cable This connector provides the source voltage to the 16117C This is a high voltage BNC connector and is not compatible with standard BNC connectors 2 Triaxial cable The measured signal is carried on the center conductor of this connector 3 Interlock cable This connector enables the interlock function which enables and di2. This chapter explains how to install the 16117C Low Noise Test Lead The topics covered include initial inspection ambient environmental considerations connecting the adapter for use and repackaging the adapter for shipment Initial Inspection The adapter has been carefully inspected electrically and mechanically before being shipped from the factory It should be in perfect physical condition no scratches dents or the like and it should be in perfect electrical condition Verify this by carefully performing an incoming inspection to check the adapter for signs of physical damage and missing contents If any discrepancy is found notify the carrier and Agilent Technologies Your Agilent Technologies sales office will arrange for repair and replacement without waiting for the claim to be settled 1 Inspect the shipping container for damage and keep the shipping materials until the incoming inspection is completed 2 Verify that the shipping container contains everything shown in Figure 2 1 and listed in Table 2 1 3 Inspect the exterior of the 16117C for any signs of damage Preparation for Use 2 1 ee ow A9302003 Figure 2 1 Product Overview Table 2 1 Contents 2 y ay Ve if Description Agilent Part Number Quantity D Low Noise Test Lead 16117C 1 BNC Female Connector 1250 2317 1 Triaxial Female Connector 1250 2228 1 O Operation and Service Manual 16117 90041 1 1 Operation and Ser
3. 339B current limit and output voltage correspondence is listed in Table 3 2 Table 3 2 ID Signal Condition IDs Condition Test Fixture Description ID3 ID2 ID1 GND GND GND 16339A No Limitation GND GND Open 16008B No Limitation GND Open GND 16117B Current Limit 0 5 mA GND Open Open 04339 65005 100 V maximum Current Limit 1 mA Open GND GND Not Applicable N a Not Used No Voltage output Open GND Open N A Open Open GND N A Open Open Open N A All IDs are opened No Voltage output By grounding all ID lines the 4339B has no set current and output voltage limitations other than the current and output voltage limits of the 4339B itself In which case if the Interlock line is grounded the 4339B can apply a source voltage of up to 1000 V If the interlock connector is not connected all ID lines are all open so the 4339B will not apply a source voltage 3 4 Operation Example Configuration of Custom Test Fixture Warning Agilent Technologies shall NOT LIABLE for any damages or dangers to the b operator incurred on use of a customized product except for the 16117C itself Follow the instructions in following example of making test fixture the operator can operate safely for high voltage measurements Figure 3 4 shows an example of test fixture configuration This example shows the test fixture for measuring insulation r
4. Agilent 16117C Low Noise Test Lead Operation and Service Manual opie Agilent Technologies Agilent Part No 16117 90041 Printed in JAPAN July 2001 Fifth Edition Notice The information contained in this document is subject to change without notice This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Agilent Technologies Agilent Technologies Japan Ltd Component Test PGU Kobe 1 3 2 Murotani Nishi ku Kobe shi Hyogo 651 2241 Japan Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period of one year from the date of shipment except that in the case of certain components listed in this manual the warranty shall be for the specified period During the warranty period Agilent Technologies will at its option either repair or replace products which prove to be defective For warranty service or repair this product must be returned to a service facility designed by Agilent Technologies The Buyer shall prepay shipping charges to Agilent Technologies and Agilent Technologies shall pay shipping charges to return the product to the Buyer However the Buyer shall pay all shipping charges duties and taxes for products returned to Agilent Technologies from another country Agilent
5. Female 1250 2317 1 BNC Connector Female 16117 90041 1 Operation and Service Manual 1 not including a model label 2 including a warning label and a cable tie Warning These servicing instructions are for use by qualified personnel only Do b NOT perform any servicing other than that contained in the operating section unless you are qualified to do so Service 4 1
6. Technologies warrants that its software and firmware designed by Agilent Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Agilent Technologies does not warrant that the operation of the instrument or software or firmware will be uninterrupted or error free Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Agilent Technologies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Certification The Agilent Technologies certifies that this product met its published specifications at the time of shipment from the factory Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institute s calibration facility or to the calibration facilities of other International Standards Organization members Exclusive Remedies The remedies provided herein are the buyer s sole and exclusive remedies Agilent Technologies shall not be liable for any direct indirect special incidental
7. ation 3 5 Interlock lines are configured as m No current and source voltage limitation All ID lines are connected to ground m Interlocking the source voltage output with open and close the cover of test fixture Interlock switch is connected in series to Interlock line brown This switch turns on and off together with opening and closing the cover of the customized test fixture Note It is recommended that interlock line should have two or more switches This is i effective to avoid unexpectedly applying source voltage due to trouble with the 3 interlock switch m Automatic resistivity mode change is not used Special Signal line black is not connected Note The end of unconnected line should be covered with insulations to avoid i contact to ground w Checking Procedure The 16117C and the 4339B is operated with high voltage up to 1000 V These products are designed that operator can measure safely To keep safety condition you must execute following checking procedure periodically This procedure assumes your fixture has top cover interlocing source voltage output of the 4339B Warning Do NOT touch the electrode and UNKNOWN connector while the High b Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off Daily Safety Verifica
8. esistance This custom test fixture has a cover for contacting the DUT and the source voltage is interlocked with open and close of this cover BNC connector High Voltage AN Interlock cable 1 ny ES to chassis N This line supplies source voltage in floating DUT measurement configuration x Interlock Switch DUT electrode Cover Open Cover Open a dt Close Close hs ui TRIAXIAL connector AU A9303005 qse line supplies source voltage in grounded DUT measurement configuration Fixture Main Body AAN ndcates dengerous point for high voltage up to 1000 V Figure 3 4 Example Configuration of Custom Test Fixture Center conductor of BNC connector and center conductor of triaxial connector is connected to contact of DUT A source voltage of up to 1000 V is applied these lines and the inner shield of triaxial connector So you must use cable which can withstand a voltage greater than 1000 V The inner shield of the triaxial connector is extended close to the DUT contact as a guard line Warning You must design the test fixture so the operator can not touch the points A which are indicated or the dangerous voltage symbol in Figure 3 4 to avoid electrical hazards to the operator Specially around the electrodes should be protected with a cover which is interlocked with source voltage output Oper
9. ing the source voltage and current limit function To enable this function in your custom test fixture the 16117C provides an interlock cable This section describes how to use interlock circuit to meet your custom test fixture requirements Figure 3 3 shows pin assignments for the interlock cable GND Interlock Brown Special Signal ID4 Black Red ID3 ID2 W hite Orange Figure 3 3 Interlock cable Assignment Wiring Side View The interlock cable has six lines The 4339B changes some settings Voltage Output Current Limit and Resistivity Mode depending on the interlock status Table 3 1 describes the role of each line Table 3 1 Pin Assignment of Interlock Connector Pin Name Description Interlock Interrupt signal Disable or enable Voltage Output ID1 State signal Identificate Test Fixture 1D2 1D3 Special Signal State signal used for 16008B switching ps and pv GND Ground Connected to Chassis 1 When Interlock line is grounded voltage output is enabled 2 Refer to Table 3 2 3 When the special signal line is grounded the pv RV mode is selected Operation 3 3 The ID signals are used by the 4339B to identify the current limit and the output voltage performance requested by the test fixture The 4339B is programmed beforehand to change the current limit and output voltage settings according to the ID line status The ID status test fixture identification and the 4
10. isted in Table 1 1 are supplied with the 16117C Table 1 1 Furnished Accessories Description Part Number Quantity Operation and Service Manual P N 16117 90041 1 General Information 1 1 Operating and Safety Precautions Service The voltage levels up to 1000 V in this adapter warrants extreme care for operator safety Service must be performed only by qualified personnel Specifications This section lists the complete 16117C specifications These specifications are the performance standards and limits against which the 16117C is tested When shipped from the factory the 16117C meets the specifications listed in this section Applicable Test Voltage 2 0 00 ccc cece enn e ees 1000 V maximum Applicable Test Current 00000000 000 ccc ccc ccc ccc cece cece eee seen eneees 10 mA maximum Applicable Instrument nananana nnana nnana aaea 4339B Interlock Circuit naa unauna eunana arareo eaaa furnished Cable Length 2 00 0 cence tenet ene eens 1 m connector to connector Operating Temperature 00 00 0 rreren renee ruere rruen rennen O to 55 C Operating Humidity 00 00 0000 cence nce n tenn as lt 70 RH 40 C Non operating Temperature 0 00 n tent eens 40 to 70 C Non operating Humidity 0 0 0 0 00 n ees lt 95 RH 40 C 1 Maximum measurable current of the 4339B is 100 pA 1 2 General Information Preparation for Use Introduction
11. ment The Agilent Technologies assumes no liability for the customer s failure to comply with these requirements Note 16117C is designed for use in INSTALLATION CATEGORY I according to IEC i 61010 1 and POLLUTION DEGREE 1 according to IEC 61010 1 and IEC 60664 1 3 16117C is an INDOOR USE product Do NOT operate in an Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a safety hazard Keep Away from Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made only by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injury always disconnect power and discharge circuits before touching them Do NOT Service or Adjust While Alone Do not attempt internal service or adjustment unless another person capable of turning off power and capable of rendering first aid and resuscitation is present Do NOT Substitute Parts or Modify Instrument Because of the danger of introducing additional hazards do not substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Agilent Technologies Sales and Service Office for service and repair to ensure the safety features are maintai
12. ned Dangerous Procedure Warnings Warnings such as the example below precede POTENTIALLY DANGEROUS PROCEDURES throughout this manual Instructions contained in the warnings must be followed Warning Dangerous voltages capable of causing death are present in this b instrument Use extreme caution when handling testing and adjusting this instrument Safety Symbols General definitions of safety symbols used on equipment or in manuals are listed below A MS O Warning q Caution 7 Note vi A Instruction manual symbol the product is marked with this symbol when it is necessary for the user to refer to the instruction manual Alternating current Direct current On Supply Off Supply This Warning sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in injury or death to personnel This Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like which is essential to highlight Affixed to product containing static sensitive devices use anti static handling procedures to prevent electrostatic discharge damage to component Cauti
13. on risk of electric shock Terminals which may be supplied from the interior of the equipment at a voltage exceeding 1 kV or allow connection to a voltage exceeding 1 kV are marked with this symbol Contents 1 General Information Introduction a a a a a l 1 Using the 16117C aaa aa a 1 1 Product Description ee 1 1 Accessories Supplied 2 6 1 A 1 1 Operating and Safety Precautions 2 2 ee a 1 2 Service 26 aa a L 1 2 Specifications oaoa a a a A 1 2 2 Preparation for Use Introduction o a a a a 2 1 Initial Inspection a a a a a a a 2 1 Ambient Environmental Considerations 0 0 22 2 20084 2 3 Operating and Storage 2 oa a a a e 2 3 Connecting the Adapter for Use 2 ee 2 3 Packaging the Adapter 2 2 2 ee 2 4 3 Operation Introduction 2 a a a a a 3 1 Making a Custom Test Fixture oaoa aa a a e 3 2 Configuration oaoa a a a 3 2 Interlock Circuit oa a a 3 3 Example Configuration of Custom Test Fixture a a a a a a a a a 3 5 Checking Procedure oao a a a a 3 6 4 Service Introduction o oa a a a a CA Ce 4 1 Replaceable Parts 2 2 A 4 1 Contents 1 Figures 2 1 Product Overview 2 1 1 a a a a 2 2 2 2 Floating DUT Measurement 2 0 ee 2 3 2 3 Grounded DUT Measurement 2 2 a a 2 4 3 1 Adapter Features 2 A 3 1 3 2 Floating DUT Measurement Configuration 0 04 3 2 3 3 Inte
14. or consequential damages whether based on contract tort or any other legal theory Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products If you need assistance contact your nearest Agilent Technologies Sales and Service Office Addresses are provided at the back of this manual Copyright 1991 1999 2000 2001 Agilent Technologies Japan Ltd Manual Printing History The manual printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates which are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated December 1991 00 0 0 tne EEEE EEEE EEE EEEE First Edition February 1999 l a naaa een nen bb teen ten eens Second Edition July 1999 Third Edition part number 16117 90031 May 2000 ooe aaaeeeaa ennor Fourth Edition part number 16117 90031 July 2001 eeaeee Fifth Edition part number 16117 90041 Safety Summary The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS elsewhere in this manual may impair the protection provided by the equipment In addition it violates safety standards of design manufacture and intended use of the instru
15. rlock cable Assignment Wiring Side View 2 0 3 3 3 4 Example Configuration of Custom Test Fixture 0084 3 5 Tables 1 1 Furnished Accessories 1 1 oa aa a 1 1 2 1 Contents 2 a 2 2 3 1 Pin Assignment of Interlock Connector 080084 3 3 3 2 ID Signal Condition 2 2 a a 3 4 4 1 Replaceable Parts List 2 2 2 2 ee 4 1 Contents 2 General Information Introduction The purpose of this manual is to enable you to use your 16117C Low Noise Test Lead efficiently and confidently This manual contains both general and specific information To use the 16117C to perform a specific function without having to read the entire manual follow the directions in Using the 161170 Using the 16117C The 16117C has been designed to operate specifically with the 4339B High Resistance Meter a To install the 16117C turn to Chapter 2 m To operate the 16117C turn to Chapter 3 a To order replaceable parts for the 16117C turn to Replaceable Parts in Chapter 4 Product Description The 16117C has been designed to operate specifically with the 4339B High Resistance Meter The 16117C is used to measure insulation resistance The 16117C has the following features a Prepared exclusive connector for the 4339B This allows easy to make original test fixture for the 4339B m High voltage safety designed using an interlock circuit Accessories Supplied The accessories l
16. sables the application of the source voltage from the 4339B when the interlock line is connected and disconnected respectively 4 BNC female connector 5 Triaxtal female connector Operation 3 1 Making a Custom Test Fixture This section describes how to make a custom test fixture for the 4339B Note When you make a custom test fixture using the 16117C you must observe the i usage guidelines described in this section 2 Configuration The 16117C is provided so the user can make custom test fixtures for the 4339B Figure 3 2 shows an simplified configuration of test fixture in floating DUT measurement with the 16117C A around A Guard Y Source Voltage 4 Signal y_ Ground TN My LA Triaxial A9303002 Figure 3 2 Floating DUT Measurement Configuration The BNC connector provides source voltage up to 1000 V A triaxial connector is used for the measured signal path The triaxial connector s center conductor carries the signal The inner shield is a Guard and the outer shield is the ground Using a guard circuit eliminates the external noise to the center conductors The Guard must extend as close as possible to the DUT contact but not connected For information about the Grounded DUT measurement configuration refer to 4339B High Resistance Meter Operation Manual 3 2 Operation Interlock Circuit The interlock circuit automatically enables interlock
17. tion Procedure 1 Connect the your fixture to the 4339B 2 Close the top cover of your fixture 3 Set source voltage to 42 V 4 Press V output key of the 4339B Confirm that the V output indicator and the High Voltage indicator turn on 5 Open top cover of your fixure Confirm that the High Voltage indicator turnes off immediately 6 Close the top cover again Confirm that the High Voltage indicator still turns off If you encountered any errors in checking procedure contact your nearest Agilent Technologies Office 3 6 Operation Service Introduction This chapter gives the replaceable parts information for the 16117C Replaceable Parts Table 4 1 identify the replaceable parts Do not disassemble the 16117C any further than shown in Table 4 1 The listed parts can be ordered from your nearest Agilent Technologies Office Ordering information should include the Agilent part number and the quantity required Table 4 1 Replaceable Parts List Agilent Part Number Qty Description 16117 87102 1 Model Label 16117 40001 1 Holder 16117 40002 1 Holder with Nuts 16117 87108 2 Warning Label Red on BNC and Triaxial cable 16117 87104 1 Label Yellow on Interlock cable 16117 61604 1 Cable Assembly Triaxial 16117 61605 1 Cable Assembly BNC 16117 61606 1 Cable Assembly Interlock 3050 0891 2 Washer Flat to fix a holder 0515 1552 2 Screw Pan Head to fix a holder 1250 2228 1 Triaxial Connector
18. vice Manual is not shown in Figure 2 1 2 2 Preparation for Use Ambient Environmental Considerations Operating and Storage The 16117C must be operated within an ambient temperature range of 0 C to 55 C and relative humidity up to 70 RH at 40 C non condensing The 16117C may be stored within a temperature range of 40 C to 70 and at a relative humidity up to 95 at 40 C non condensing Connecting the Adapter for Use The 4339B connection with 16117C has two configurations floating and grounded DUT measurement configurations The connections are different for each configuration The connections are as shown in Figure 2 2 and Figure 2 3 Warning Do NOT touch the electrode and UNKNOWN connector while the High A Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off DOOS A9302001 Figure 2 2 Floating DUT Measurement Preparation for Use 2 3 o A IO poou aooo DoofBgalbpcos E
Download Pdf Manuals
Related Search