Home

The Owens Family

1. S which includes the front seat side air bags to deactivate 2 8 9 Tilt the entire seat assembly back to access all of the vehicle harness to seat connectors Then disconnect them from the seat 10 Remove the seat assembly from vehicle and place it on a clean dry surface use a fender cover or large floormat Place it with the seat back lying flat to expose the underside of the seat 11 Unhook the carpet flap from the underside of the seat bottom see figure 3 R oA mE a me ells l Hook for j aieas carpet flap pS 3 sS olki L L TN O Fender J cover Seat side rail PE Figure 3 12 Remove four M8 12mm head bolts which will release the seat bottom cushion from the seat frame see figure 4 e Then remove the two M6 10mm head bolts from the seat track mounting tab on both sides see figure 4 e Removing these bolts will release the seat slide rails from the worm gears m Seat bottom cushion Seat bottom cushion bolt bolt INA e O S i C 2 Seat track Seat track ov A ml O Seat track mounting tab Seat track mounting tab bolt bolt Seat bottom cushion bolts TP000830 Figure 4 3 8 13 Remove the top screw only from the RH amp LH side finishers see figure 5 e f equipped remove both screws and f
2. ae 9 fl NY o aN A 4 Slide both seat 4 A rails downward TP000833 Figure 7 16 Remove the flexible wire from the gear boxes To release the flexible wire from the motor end pull up on the tab using a flat blade screwdriver or equivalent see figure 8 Flexible wire a connector Release tab Motor J Figure 8 TP000834 5 8 17 Make sure the new seat track mounting tab is touching the rear stopper with the threaded shaft facing up see figure 9 e Measure the distance between the gear case and the mounting tab see figure 9 e Measure and adjust the other seat track mounting tab to the same distance see figure 9 Turn shaft to adjust Gear box Rear stopper connector Flexible ae r 7 ie Adjust this distance Seat track to match this distance mounting tab Seat track ee mounting tab Worm ae TP000835 Figure 9 18 Replace all six rubber grommets 3 on each side from the kit see figure 10 Replace all 6 grommets Figure 10 NOTE For steps 19 through 22 below refer to figures 6 and 7 on page 4 and 5 if needed 19 Put the worm gears gear boxes and flexible wire assembly all as one unit back into seat frame CAUTION Avoid bending the flexible wire Bending the flexible wire will result in a noise during seat operation 20 Mov
3. e both seat tracks back into position on top of the seat track mounting tabs Install and hand tighten the M6 10mm head bolts into both seat track mounting tabs 6 8 21 Tighten the six base plate nuts three on each side located at the top of the seat frame to secure the gear boxes Nut torque 64 85 in lb 7 17 9 69 Nm 22 Re install and tighten two M8 12mm head bolts located to the sides of the front edge of the seat see figure 6 Bolt torque 13 17 ft lb 17 5 23 7 Nm 23 Check the gear case to mounting tab distance again Make sure they have not moved see figure 11 If N G adjust T m A Recheck amp compare distance must be the same ID oo NH oo TP000837 Q Q Q A IQ Q Q Q Q Figure 11 24 Tighten M6 10mm head bolt into both seat track mounting tabs Bolt torque 65 84 in lb 7 3 9 4 Nm 25 Re install screws to attach the side finishers refer to figure 5 on page 4 if needed 26 Re install four M8 12mm head bolts to tighten the seat bottom cushion to the seat frame refer to figure 4 on page 3 if needed Bolt torque 13 17 ft lb 17 5 23 7 Nm 27 Re connect slide motor connector making sure it snaps in place 28 Re hook strap to attach the carpet flap onto the bottom of the seat refer to figure 3 on page 3 if needed 29 Place the seat assembly back into the vehicle and re connect all elect
4. inisher from the front edge of the seat see figure 5 seat finisher trim screws if equipped Seat side trim screws TP010758 Figure 5 14 Disconnect the seat sub harness connector to slide motor see figure 6 e Remove M8 12mm head bolt from both sides of the seat frame located to the sides of the front edge of seat see figure 6 e Then remove six nuts and two base plates on both sides located at the top of the seat frame to release the gear boxes see figure 6 Remove this bolt first Then remove these 6 nuts amp the 2 base plates Remove this bolt first Base plates q Front edge of seat lower frame Gear pox Seat sub harness Slide motor connector to slide motor g Front of seat rail Front of seat rail Lue O 2D TP010759 Figure 6 4 8 15 Slide both of the seat rails back to the rear position towards the seat back and remove the worm gears flexible wire motor and gear boxes all as one unit from the seat adjuster assembly see figure 7 CAUTION Avoid bending the flexible wire Bending the wire will result in a noise during seat operation Lift out motor flexible wire worn gears Gear box and gear boxes as an assembly A Flexible wire D 1 i Connector m T Motor amp gear box ot TON Aa T
5. issan Warranty Flat Rate Manual and use the indicated FRT 8 8
6. lor wires in the seat slide motor connector e Refer to Power Seat or Automatic Drive Positioner in the EL section of the appropriate Service Manual WARNING When checking the power seat slide motor circuit do not confuse its black connector with the side air bag module yellow connector see figure 2 Side air bag connector Do Not probe this connector Figure 2 e This voltage check can be done with the seat slide motor connected or disconnected e f voltage is about 12v when the seat slide switch is pressed to the forward and backward positions proceed to step 3 e f voltage is Ov when the seat slide switch is pressed to either the forward or backward positions this bulletin does not apply Use the EL section of the appropriate Service Manual to further investigate 3 Record the radio station pre sets for later reprogramming after the procedure 4 Lightly tap the seat slide motor see figure 2 Sometimes this will get the motor working again temporarily so the seat can be moved to access the seat mounting bolts 5 Move the seat bottom all the way forward and remove the two M10 14mm head rear seat mounting bolts 6 Move the seat all the way to the back position and remove the two M10 14mm head front seat mounting bolts 7 Turn the ignition key OFF 8 Disconnect the battery negative cable and wait three 3 minutes This will allow the Supplemental Restraint System SR
7. rical connectors Make sure they all snap together securely 30 Re connect the battery negative cable 31 Re install four seat mounting bolts Bolt torque 27 36 ft lb 37 49 Nm 32 Operate the seat switches to ensure normal operation has returned 7 8 33 For the ADP entry exit feature if equipped to return to normal operation procedure A or B must be performed Procedure A a Insert key into the ignition key cylinder Ignition switch is in OFF position b Open close open the driver side door Do not perform with the door switch operation c End Procedure B a Drive the vehicle at more than 25 km h 16 MPH b End 34 Re program the radio presets 35 Re set the clock PARTS INFORMATION C i iESRIPEECCN S PART QUANTITY Seat Slide Motor Kit for vehicles with ADP 87562 C9926 Seat Slide Motor Kit for vehicles without ADP 87562 C9927 CLAIMS INFORMATION NOTE This is the ONLY approved repair procedure for this incident A claim to Nissan for the repair of this incident may be denied if the repair is not performed exactly as outlined in this bulletin Submit a Primary Failed Part PP line claim using the following claims coding ____ DESCRIPTION PEP OPCODE SM DA FAT RPL Seat slide motor amp gear 1 VH80AA ZE 32 2 1 Reference the Parts Information table above and use the indicated Seat Slide Motor Kit P N as the PFP 2 Reference the current N
8. yO NISSAN NORTH AMERICA INC NISSAN Copyright SERVICE BULLETIN Classification EL01 030c NTB02 001 c July 23 2002 2000 2003 MAXIMA DRIVER S POWER SEAT WILL NOT MOVE FORWARD OR BACKWARD IMPORTANT This bulletin has been revised The Parts and Claims Information sections of this Bulletin have been amended Please discard previously released copies of NTB02 001 APPLIED VEHICLES 2000 2003 Maxima A33 SERVICE INFORMATION If the driver s seat in an applied vehicle will not move in the forward or backward direction the seat slide motor and gear assembly may need replacement see figure 1 Driver s Seat Bottom of Driver s Seat Slide motor and gear assembly zi Mi A D Ley Q ol TP000828 Figure 1 If this should occur follow the Service Procedure in this bulletin to assist in diagnosing the incident and if necessary install the Seat Slide Motor Kit see Parts Information in this bulletin for detail NOTE This is the ONLY approved repair procedure for this incident A claim to Nissan for the repair of this incident may be denied if the repair is not performed exactly as outlined in this bulletin 1 8 SERVICE PROCEDURE 1 Using the power seat switch tilt the front edge of the seat bottom all the way up 2 Check the voltage to the seat slide motor e Measure voltage on the harness side between the BR and W B co

The Owens Family

Contents

Download Pdf Manuals

Related Search

Related Contents