screamin` eagle performance air cleaner kit - Harley
Contents
1. head but do not tighten 6 Thread air cleaner mounting screws 4 through mounting bracket 6 and into backplate 2 until screw threads are captured in induction module Leave fasteners loose 7 Alternately tighten two breather screws A to 120 144 in Ibs 13 6 16 3 Nm 8 Tighten three air cleaner screws 4 to 55 60 in Ibs 6 2 6 8 Nm 9 Press breather plugs 5 into breather screw cavities aligning tubes with recesses in backplate Install Air Cleaner Filter and Cover NOTE Whenever the air cleaner cover is installed apply Loctite 243 blue to the air cleaner cover screw 8 1 See Figure 1 Install the air cleaner filter element 7 and cover 9 Before tightening the center screw align the cover using the medallion for best appearance Tighten center screw to 36 60 in Ibs 4 1 6 8 Nm NOTE Apply a small amount of dish soap to medallion O ring to aid in installation of medallion 1 of 3 Please dispose of materials responsibly 2 Install the medallion into the center hole by pressing in place Do not damage the O ring Final Assembly 1 Install main fuse Refer to the service manual NOTES Install the rain sock over the air filter element in wet or rainy conditions to prevent water intrusion Install the pre charger 13 over the air filter element under these circumstances Recalibrate ECM NOTICE You must recalibrate the ECM when installing this kit Failure to properly recalibrate th2. ap the element to dislodge any loose dirt Gently brush with a soft bristle brush d EITHER spray air filter cleaner liberally onto the cotton filter media OR roll and soak the media in a shallow pan of air filter cleaner removing immediately In either case set the filter media aside to soak for ten minutes e Rinse off the filter media flowing from the clean side to the dirty side with low pressure tap water f After rinsing shake off excess water Let the filter media air dry DO NOT use compressed air or a heat gun to speed drying g After the filter media is dry EITHER spray air filter oil along each pleat once only holding the spray nozzle approximately 3 in 76 mm away from the media OR carefully use a squeeze bottle to deposit oil along each pleat once only Let the oil absorb into the filter media for 20 minutes before proceeding After 20 minutes inspect the filter media Carefully apply oil to any remaining visible white spots on the filter media Allow to absorb 2of3 SERVICE PARTS is08589a Figure 1 Service Parts Screamin Eagle Performance Air Cleaner Kit Table 1 Service Parts Item Description Quantity Part Number 1 O ring 2 113 2 11292 2 Backplate chrome Kit 29400117 29510 05 Backplate black Kit 29400116 29400081 3 Gasket throttle body 29583 01A 4 Screw socket head cap 1 4 20 x 2 0 in 51 mm long 3 Not sol
3. cMOTOR HARLEY DAVIDSON WY J05667 INSTRUCTIONS REV 2015 04 21 SCREAMIN EAGLE PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 29400116 29400117 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements Proper installation of this kit requires the use of Digital Techni cian at a Harley Davidson dealer Loctite 243 Medium Strength Threadlocker and Sealant Blue Part No 99642 97 is required for proper installation of this kit IWIN NIN The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 1 and Table 1 NOTES The kit is intended for High Performance applications only Engine related performance parts are intended FOR THE EXPERIENCED RIDER ONLY NOTES Installation of this kit by an authorized Harley Davidson dealer does not affect your limited vehicle warranty The Prod
4. d separately 5 Plug breather 2 29557 05 6 Bracket mounting 29400119 7 Air filter element 29400118 8 Screw hex socket flat head 5 16 18 x 2 0 in 51 mm long Not sold separately 9 Cover air cleaner Not sold separately 10 Medallion Screamin Eagle 14100367 11 Screen air filter black Kit 29400116 29400082 Screen air filter chrome Kit 29400117 29400100 12 O ring medallion 11170 13 Pre charger 29400121 Items mentioned in text but not included in kit A Breather screw 2 B Induction module bracket remove and discard J05667 3of3
5. e ECM can result in severe engine damage 00399b Download the new ECM calibration using the Digital Techni cian at a Harley Davidson dealer Air Filter Element Maintenance 1 Inspect the air filter element every 5000 miles 8000 km or more often under dusty conditions NOTES The use of other cleaning drying or oiling methods or products damages the filter and voids the manufacturer s warranty K amp N Air filter Cleaner is available from a Harley Davidson dealer either alone 1 qt 0 95 L sprayer bottle Part No 99883 88T or a 12 fl oz 0 35 L sprayer bottle as part of the Filter Care Service Kit Part No 99850 92T K amp N Air Filter Oil is also available from a Harley Davidson dealer either alone 12 25 02 347 gram aerosol can Part No 99882 88T or a 6 5 02 184 gram aerosol can as part of the Filter Care Service Kit J05667 DO NOT OVER OIL THE AIR FILTER Over oiling interferes with the proper performance of the engine and or certain engine components If oil is still draining or dripping from the filter media 20 minutes after oiling clean and oil the filter element again 2 Toclean the element a Remove the center medallion by inserting a small flat blade screwdriver in the slot at the bottom of the medallion Carefully work around the center portion without scratching the finish of the air cleaner cover Rotating the medallion aids in its removal b Remove the air cleaner cover center screw c T
6. uct Information Label contained in this kit is a requirement of the California Air Resource Board CARB emission regulation for all 2000 and later Softail and 1999 and later Dyna models Place the label on the right side of the frame directly beneath the VIN sticker This label is not required outside the state of California The kit is intended for High Performance applications only This engine related performance part is legal for sale or use in California on pollution controlled motor vehicles J05667 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled REMOVAL 1 Remove main fuse See the service manual 2 Remove the existing air cleaner per the service manual Save the two breather screws from the backplate Remaining parts can be discarded 3 See Figure 1 Remove and discard induction module bracket B INSTALLATION Install Air Cleaner NOTE When servicing air cleaner apply Loctite 243 blue 99642 97 to all fastener threads 1 See Figure 1 Install two O rings 1 from kit in grooves around breather screw holes on induction module side of backplate assembly 2 2 Align flat edge of gasket 3 with the molded tab Install gasket on induction module side of backplate 3 Insert breather screws A through the backplate 4 Apply Loctite 243 blue to breather screw threads and mating tapped holes in cylinder head 5 Thread screws into cylinder
Download Pdf Manuals
Related Search