Integrated Power Console (IPC™)
Contents
1. Oo Damaged handpiece or finger lever base out of position registry entr registry entr UI self test failure corrupt usage data file or unable to create usage data file 28 MCB self test failure bridge transistor 1 shorted o2 MCB self test failure bridge transistor 2 29 shorted MCB self test failure bridge transistor 3 shorted MCB self test failure bridge transistor 4 Self Test Failed Power off Wait 10 seconds Power on If error persists 31 Eod call Technical Services EE MCB self test failure bridge transistor 5 22 shorted MCB self test failure bridge transistor 6 33 shorted 18 Finger Control Error Power off Wait 10 seconds Power on If error persists call Technical Services Self Test Failed gt 20 Changing the Fuse ud EC REP Mecdirormuc MEDTRONIC XOMED INC 6743 Southpoint Drive North Jacksonville FL 32216 USA www medtronicENT com www medtronicENT TechComms com Medtronic B V Earl Bakkenstraat 10 6422 PJ Heerlen The Netherlands Tel 011 31 45 566 8000 Fax 011 31 45 566 8668 0123 2010 Medtronic Inc All rights reserved Printed in the USA 05 2010 REF 1898851F 68M0006 B2. StraightShot Magnum II Microdebrider StraightShot III Microdebrider Midas Rex SC1 Visao or Skeeter handpieces and the Multi Function Foot Control Unit Auxiliary Power Outlet with protective cover is for use with the HydroDebrider or Bone Mill consoles only W6 Sterilize and dry reusable device before storing the system Decrease likelihood of cross contamination with timely sterilization 7 After each procedure properly clean all reusable system components Auxiliary Power Outlet with protective cover is for use with the HydroDebrider or Bone Mill consoles only Precaution P1 Prime Flush Priming is a feature designed to purge air out of the tubing set s during setup The first time a Prime or Flush button is pressed it will turn on pump 1 and or 2 long enough to purge air out of the tubing set s Turning power Off and On resets the Prime feature Once pressed all Prime buttons will change to Flush buttons System Description The IPC System is a powered microdebrider drill and saw system that will remove soft tissue hard tissue bone and biomaterials during surgical procedures The system consists of a power control console footswitch connection cables and assorted handpieces to drive various burs blades drills rasps cannulae and saws It includes integrated irrigation pumps for irrigation of blades burs and for motor coolant The Nerve Integrity Monitor NIM is a separate device that stimula
3. Help Line 800 874 5797 Medtronic Powered Surgical Solutions 4620 North Beach Street Fort Worth TX 76137 USA WWNW medtronic com U S Help Line 800 468 9710 International Service International customers should contact their local Medtronic representative Console Front gt INTEGRATED POWER console _ awa Em Initialization in Progress Touchscreen User interface Pump 1 Coolant lens cleaning or irrigation Pump 2 Irrigation Connector Panel peripheral devices Power Switch System On Off switch Connector Panel ee Component Midas Rex Legend EHS motor Midas Rex Legend EHS Stylus motor StraightShot M4 Microdebrider Midas Rex Legend EHS Stylus Touch motor Midas Rex SCI StraightShot Magnum II and StraightShot III Visao a NN connection NIM L t Stimulus output to STIM Bur Guard 1 F Skeeter Handpiece OOO O l O Endo Scrub 2 Finger Switch G Endo Scrub 2 Footpedal IntelliFlow Irrigation Remote Control Foot Control Unit FCU Connector Panel Cable Connection Cable to console connection red silver dot e Red or silver dot connections are multi pin and must be correctly aligned oriented Cable to console connection without dot e Connectors without the red or silver dot are single pin and may be inserted without regard to orientation Connector Panel Cable Disconnection multi pin To Remove Midas Rex To Remove Midas Re
4. I ib mdu radadpueH 3 i a Cao 5 MEnNIEHADDL qed cagader in E Bred supu ug l 8 zagedpuen X pw pano aga Bi L asexdpuen penu agog dweep siad EY Mepa e YES sped US 16 Failed internal components Contact Customer Care Pumps dont run Moisture ingress in cable conflicts with Run a dry cycle when sterilizing If problem persists contact Customer handpiece recognition Care Tubing Set improperly seated in pump TE ES P pups verify pump lid is fully closed with the fluid Check tubing at side of pump see Irrigation Coolant Pumps Tubing is pinched or kinked Check remaining tubing for pinched or kinked areas if necessary replace Little or no irrigation flow tubing Tubing clamps are restricting flow Set tubing clamps in open position Irrigation flow rate setting low Adjust irrigation flow rate Irrigator obstructed Reposition tubing in pump verify pump lid is fully closed with the fluid THDIHSOCCUNDIODORE SCRI CODI Pua flow from left to right If problem persists contact Customer Care Pump stall error Check tubing is not pinched or kinked on side of pump see section on Tubing is pinched or kinked Irrigation Coolant Pumps If problem persists contact Customer Care Console default parameters incorrect Handpiece connected but console reads Connect Handpiece Handpiece connected but console displays incorrect handpiece Moisture ingress in
5. Switch attachments to determine whether the heat is being generated by Attachment transferring heat to the FDT E Here NEE IN Motor is too hot to touch hold ies Contact Customer Care Discontinue use and rest the motor by using it intermittently or wrap the Heavy side loading during dissection motor with a moist sterile towel If overheating continues contact Customer Care Ensure adequate irrigation to surgical site during bone dissection Inadequate irrigation Aging of attachment Use of reprocessed tools Contact Customer Care Tool is difficult to remove from manual Improper cleaning Use the Legend motor wrench to rotate the flat closest to the motor case until its marker is aligned with the marker on the flat farthest away from duse WOU Seay propery Motor collet flats are not aligned Eee the motor case Cables not properly connected Ensure motor and foot control cables are properly connected Speed setting is too low e a speed greater than 10 000 rpm EHS or 3 000 rpm Stylus Attachment not properly installed and Remove and reinstall the attachment and dissecting tool to ensure locked onto the motor proper installation Motor does not run Internal failure of motor and or Change motor or console to isolate the problem console Contact Customer Care Check for obstruction under the foot pedal TOOTOO ot poper unchonme If problem persists contact Customer Care Cables damaged Ch
6. Terminal PN 11190620 and Components in direct contact with the Back Panel PN 11683316 Applicable test 25 Ampere 60Hz ground bond for 5 seconds per IEC 60601 1 Clause 8 6 4 a Applicable result lt 100 milli Ohm impedance Floating Metal Applicable components Pole Clamp PN 66320173 and bezel of irrigation port in Connector Panel PN 44681784 or PN 11249350 Applicable test 4000VAC high potential 60Hz 60 seconds 10 second ramp up per IEC 60601 1 Clause 8 8 3 Applicable result lt 10mA leakage Metal Shells of Type BF Electrical Connectors Applicable components Shells of footswitch 12 position handpiece and 4 position handpiece connectors of Connector Panel PN 44681784 or PN 11249350 Applicable test 2500VAC high potential 60Hz 60 seconds 10 second ramp up per IEC 60601 1 Clause 8 8 3 Applicable result lt 10mA leakage 15 aan wauwa uy paddinba 4 mogonpucs aseud yeg Tuo Jeo uj pege 1sul POU s YY Jeo Z bred Sue pewara UA paco agag e Bujan saod ay NE woy papeuuoasm A psnosueynujs 29 Eus usas au I way L ajouoa Jp sued JAW o USULI SAFI UDI inii nin aad A7 Ed E Psn WE LOL L Sir JO PS FL woes up payeds saap ubgxeoud oN 7L SES ee WEE 49018 md JEU fe yogezienba EPH d SIHD OO 0 UC SUID ou pegejneu Sno uepaeuuoz Ka iQ WES HAIN lho Fava saqiddns P3 Aue Jawod jo AQUI z pue ueuxid uzam pauE3 UEC gud QUOD apu uonEmsul pop EH agea nnn adi eo s
7. cable conflicts with Run a dry cycle when sterilizing If problem persists contact Customer handpiece recognition Care Power cord not properly connected Connect power cord Check power available i e power strip is on circuit breaker is closed No power YA Power Inlet Fuses blown Replace fuses with 5 00 A 250V time delayed fuses P N 11270066 Failed internal components Contact Customer Care ME E pene ON DHE Touch Failed internal components Contact Customer Care Screen doesnt come on Console doesn t power down Power switch failure Unplug power cord contact Customer Care Touch Screen doesn t respond Screen gasket displaced or failed Contact Customer Care internal components Touch Screen doesn t work oroperlv Console doesn t power up Touch Screen not calibrated Calibrate Touch Screen If problem persists contact Customer Care Disconnect and reconnect the motor cable Console misidentified the handpiece motor Turn console off then on Console displays wrong handpiece motor iype Change motor motor cable or console to isolate the problem Moisture ingress in cable conflicts with Run a dry cycle when sterilizing if problem persists contact Customer handpiece recognition Care Press and hold buttons for at least 1 second wait for console Incorrect use confirmation beep Top button doesn t respond One 1 handpiece connected top button has no function with 1 handpiece connect
8. on the sheath product label as malfunction or poor performance could result Endo Scrub 2 Sheath Endoscope Light source connection Irrigation connection Se pum E Endo Scrub 2 Finger switch E Finger switch cable G Endo Scrub 2 Footswitch H Endo Scrub 2 Footswitch cable Endo Scrub 2 Assembly 1 Wet v 2 Slowly insert 3 Attach irrigation and light source Suction Irrigator The Suction Irrigator may be selected via the radio button within the Irrigation Method box NOTE The suction irrigator is NOT available for microdebrider handpieces Suction Irrigator Handpiece Suction Tube Irrigation tube Suction Fitting Irrigation Fitting E Tube Size JAPE NOTE The Suction Irrigator shown here is available for all drills provided a microdebrider is not attached to the console Suction Irrigator Adapter Kit O MD P Blue Irrigation Tube Adapter fits high speed irrigation tubing 3318503 White Irrigation Tube Adapter fits IPC Visao irrigation tubing 3318603 Irrigation Connector Set is used to adjust the Blue or White Adapter to the stainless steel Irrigation Fitting D Irrigation Fitting Handpieces Microdebriders and SC1 StraightShot M4 Microdebriders and Midas Rex SC1 OMAR S Handpiece Finger wheel Locking collar Irrigation tubing groove Finger wheel lock Cable Suction barb Technical Specifications S
9. self test operation the Splash Screen will display the Setting button for about 5 seconds To change language default settings or calibrate the touch screen you must depress this button while it is displayed Settings Language English are DK i 2 BERI A This area is used to select desired language B Touch Screen Calibration button will open the calibration screen To calibrate follow the on screen instructions C The Default button will open the default screens Default 12000 4 imigafion Foot Control Unit 3 i4 T4 Ost Moda NA Mode en E IPC Blade PosiBon i B PV Mode a Theoperator can cycle through handpieces to locate desired handpiece b Theoperator may change any of the default settings to those most frequently used or view default settings c OKor Cancel button will accept or void changes and return to previous screen D OK or Cancel button will accept or void changes and return to previous screen NOTE Changing the default setting of any handpiece in no way affects the operator s ability to change settings during surgery dando stata Default Table Handpee Mode Speed ES XC sua a Midas Rex SC1 3400 X KAA Umpm StraightShot M4 12000 am eue 8000 X Edsotez amani Mee mor 70000 X me MS moi 70000 ig Midas Rex Legend eo x mem EHS Stylus motor 60000 Irrigant PHS Stylus Touch EHS Stylus Touch 9
10. 0000 X Irrigant Skeeter Handpiece 16000 EE Endo Scrub 2 TD Co m a Pump Endo Scrub 2 Setting X Connect Handpiece Footswitch Screen Lonnect Handpiece Connect Footswitch When the IPC detects no handpiece the Connect Handpiece screen will open By pressing the OK button in the Connect Footswitch panel the handpiece function will be allowed without the use of a footswitch By pressing the OK button in the Endo Scrub 2 panel the Endo Scrub 2 function will be allowed without the use of a hand piece Console Set Up Console Set Up Instructions General instructions for set up and use of the Integrated Power Console See Accessories for instructions specific to the peripheral being used NOTE Use sterile water or saline for irrigation and cooling 1 Locate cart and lock wheels 2 Inspect components for damage and determine if system is ready to use 3 On IV pole mount IPC and irrigation coolant bag s NOTE Irrigant and coolant bags should be placed above the console to ensure adequate flow 4 Position the IPC in a manner that does not obstruct the power inlet for the purpose of disconnecting the Mains voltage by the power cord Plug unit into power source 5 Connect footswitch 6 Connect the sterilized accessories to console 7 Tubing e Connect tubing as needed suction cooling irrigation 8 Turn power switch ON and verify e System passes self test e Default screen
11. Button Mode RPM selection SC1 A Pedal Start stop variable speed start stop or variable speed selectable via FCU button on main screen B Right Button If mode is set to OSC this button will rotate inner tube on blades 180 If mode is set to FWD this button will select pedal function Start stop or variable speed C Top Button Active handpiece selection D Left Button Mode selection FWD OSC NOTE If any of these condition are different check your set up if still incorrect contact Customer Service Intelliflow Irrigation Remote Control A Pause On Off e Pause if used with handpiece irrigation Flow rate will flash yellow e On Off Pause if used with Suction Irrigator B Increase Decrease e Handpiece Irrigation fine adjustment for irrigation rate e Suction Irrigator fine adjustment for irrigation rate C Increase Decrease e Handpiece Irrigation coarse adjustment for irrigation rate e Suction Irrigator selects stainless steel Fr tubing size Endo Scrub 2 NOTE Can be used only with a microdebrider The IPC System incorporates Endo Scrub 2 functionality by using irrigation pump number one 1 and controlling operation with the touch screen and an external footswitch or finger switch It is not to be used for infusion for disinfection or sterilization of an endoscope or for suction removal of blood and debris NOTE Use the Endo Scrub 2 sheath only with an endoscope listed
12. C only e HydroDebrider or Bone Mill consoles only See warning W5 To remove cover place small screwdriver in notch at bottom and pull pry off Endo Scrub 2 power connector Power cord connector See sppendix B for part numbers e Hospital grade power cord connects here e Means of disconnecting device from Mains voltage by the power cord I Equipotential e Uniform potential e Means for eliminating noise or interference with sensitive equipment by application of a POTENTIAL EQUALIZATION CONDUCTOR Power Cords North America USA Barbados Belize Bolivia Canada Columbia cip TI 1O United Kingdom Ireland Hong Kong Malaysia Continental Europe Austria Belgium Finland France Germany Greece Singapore Korea Luxembourg Ecuador Venezuela P N EA606 or Netherlands Norway Standard P N EA600 i or 1895820 1895821 Portugal Spain Sweden 6 meter P N EA650 P N EA602 or 1895822 or 189721 a India South Switzerland B P N EA604 Africa P N EA601 C P N EA607 Argentina P N EA608 Australia New Zealand P N EA605 P N EA609 P N EA610 Japan Italy Chile P N EA603 or P N EA611 1895823 Om NO For these cartridges the operator should view the Pump Setup Screen prior to installing the cartridge Console Pump Designator E Pump 1 Coolant lens cleaning or irrigation Pump 2 Irrigation or lens cleaning Pump 1 Designator This designator number is used to coordinate
13. Medtronic Integrated Power Console IPC Models EC300 and 1898001 in E INTEGRATED POWER N58 0 LE E w VM AS i RES S c TG ep 2 uM Fite SS 4 p 2 pa J ae eS er ben NC a ronic Setting Initialization in Progress Service Manual for Console and Attachments Rx Only Notice This manual is provided primarily for information purposes Although there are certain troubleshooting actions that may be attempted by the customers as specifically listed in this manual all repairs must be undertaken by Medtronic Xomed or its authorized representative Released documents are available for viewing printing www medtronicENT TechComms com are trademarks and are registered marks of Medtronic Inc The information contained in this document was accurate at time of publication Medtronic reserves the right to make changes in the product described in this manual without notice and without incorporating those changes in any products already sold IN 4 Sr M yen 5 Bena e e S IA A T AAT Ne Udo ANE DU mawa waa 5 Warnings and Precautions ese sseesesessseessseesseessseesseesseessseeoseronseosserossersseosseeessees 5 WA e 9 user e 5 System BIC 0 0 RE E 5 SAS anA SUS CM Seekers aoe cose gece eee eee 5 DS 6SHSIDIDOTS eee rere nee ire eee ere eeri
14. cm length x 2 0 cm diameter Weight 148 g Duty Cycle The Visao High Speed Otologic Drills under full load are rated for intermittent operation per the following Maximum On Time 60 seconds Minimum Off Time 30 seconds Skeeter Ultra Lite Oto Tool System Set Up and Use pz C A Tool B Tool s color code C Tool lock release button D Cannulated shaft E PTFE Bearing Technical Specifications Part No 3055601 Speed 1 000 16 000 RPM forward reverse Size 17 cm length x 1 6 cm diameter Weight 57g Duty Cycle Continuous run Storage Temperature 40 C to 70 C Humidity 1096 to 10096 RH Barometric Pressure 500 to 1060 hPa Midas Rex Legend EHS Motor High speed high torque reversible electric motor used to dissect bone and biomaterial at selectable speeds from 200 to 75 000 RPM Midas Rex Legend EHS Motor 4 pin cable connection Rotational collet Stationary collet lO Legend EHS Motor Cable Connects the motor to the console 4 pin connector Locking sleeve Green boot Cable Motor Collet Prior to installing an attachment ensure that arrows on the motor collet are in proper alignment Ung 1 Improperly aligned collets 2 Properly aligned collets 3 Motor side attachment alignment arrow If the arrows are not aligned use the Motor Wrench to turn the rotational collet until its arrow is aligned with the arrow on the stationary collet Technica
15. dhere to the following guidelines 1 When a loaner console is ordered please reuse the shipping material and carton when you return your console to Medtronic Insure the unit 2 When a loaner is not ordered please package the console as safely as possible and insure 3 Areturn goods authorization number is required on repairs A copy of your purchase order is required Make certain the purchase order includes the following e Shipping and billing information e Purchase order number e Contact person e Phone number e Description of malfunction e Your Medtronic account number 4 Please indicate preferred method of return shipment Otherwise the unit will be shipped back via UPS ground 5 When the malfunctioning unit is not covered by warranty Medtronic will contact your facility promptly with a repair cost estimate if requested The customer will be responsible for freight charges on non warranted units 6 When you have loaner equipment and you receive your repaired unit please package the loaner equipment as safely as possible using the foam provided with your repaired equipment Include paperwork indicating the unit is a loaner and Medtronic will credit your account 7 Loaner equipment not received by Medtronic within 30 days from the date that repaired equipment is shipped will be invoiced at full purchase price Medtronic Xomed Inc 6743 Southpoint Drive North Jacksonville FL 32216 USA WWNW medtronicENT com U S
16. e re E E DN HM erry 5 Medtronic Comedies epe apetiasem nie eatin rep tm 5 Be WEE C C 5 Medtronic Powered Sursical SOIUEIORBS cuiesceo ctr mitt terreno 5 LOR All Eg c aes 5 TEA NO NANA Aa 5 UONI ana 6 Conmector SAA AAA AAA AAA 6 Connector Panel Cable Connection scsccecassccesssarssracanvianssemalsceoenteecavie 6 Connector Panel Cable Disconnection multi pin 6 Cable Disconnection single DIB ia 6 Console Aa 7 PONEI COC T ne ees 7 Console Pump Desig nator aaa 7 Irrigation Coolant POIDS Aa 7 Pamp Bc Tangia be il aa IA ee ee 7 biccowluiinpES qan 7 Visao Coolant Pump SUDI 8 Standard Pump Set up s s ssssesessssssssssssesesssesessssesesesesseseseseseseseeeseseseses 8 PREC SS SOLIS 5 AU CIC Mt oci tenet niai 8 Multifunction Foot Control Unit FCU wee eere 8 Intellidow Irrigation Remote CODO sre tormentis 8 AGO SCO 2 n rc esas 8 EBdocEub 2 Assembly sectiei Ds IN EIE AU d ISE 9 UA onmi i Lo CER RONDE GIAN 9 Suction TEIG TOF Adapter Kil es abis Uistitieina era Eam Stn epit 9 Handpieces Microdebriders and SC1 sss 9 StraightShot M4 Microdebriders and Midas Rex SC1 9 Technical pecine aion ecann e itus oer tilt envie 10 StraightShot Magnum II and StraightShot III Microdebriders 10 Technical SSC MIC AOS ose edi itembti kid ara oen Enie Ei SAs 10 Handpieces EIS uacsensetesisetisi etvutreteti n tra ve
17. eck cables for cracks splits or bent connector pins Change the attachment to isolate the location of the problem Bearings are worn Contact Customer Care Check all connections from electrical source to console Poor epote Connection Ensure motor and foot control cables are properly connected Internal failure of motor console or Change motor console or cable to isolate the failing component cable Contact Customer Care Attachment not properly installed Remove and reinstall the attachment and dissecting tool Finger switch not reaching maximum Check that the control lever ring is properly seated in one of the four speed possible positions Motor with attachment rotates but an abnormal noise is heard Finger switch not responding Safety Disco anode switch in safe mode Finger control damaged Contact Customer Service 18 DO NOT use Try another attachment tube Contact Customer Care Telescoping Tubes are multi use disposable If problem is resolved with a new Telescoping Tube discard the over heated tube Heat from worn attachment tube bearings Attachment or Telescoping Tube has uncomfortable temperature to touch hold Attachment tube unclean due to iapeoper clesiine Drocedutes Check that appropriate cleaning procedures are being followed Discontinue use and rest the attachment by using intermittently try another identical attachment or wrap the attachment inter
18. ed Foot control unit buttons or pedal Disconnect and reconnect the fcu cable connector doesnt respond Connector not fully inserted Try different fcu or console to isolate the problem Contact Customer Care Internal component failure Contact Customer Care Disconnect footswitch use manual start stop rocker switch on rear of Failed footswitch console Handpiece fails to rotate r Failed handpiece motor or motor penas Contact Customer Care 17 Appears to be damaged or Damaged or defective Remove and replace defective Tool Vibrates Excessively molen WA MAANA Microdebriders pull back locking collet and re seat the tool Abnormal Noise movement y Visao unlock collar check re seat notch lock collar Blade opening is obstructed Remove blade from surgical site and submerse the blade tip in sterile NANDI YA water with suction connected to the handpiece to evacuate the l obstruction Tubing obstructed Remove and inspect suction tubing and if obstructed remove obstruction reconnect tubing Tool not seated correctly in collet Ai eee tool insertion by pulling back locking collet and re Tool wobble in Handpiece Tool wobbles in Handpiece Operate handpiece at 50 of full speed for medium long and X long burs Select a new tool Contact Customer Care Tool is leaking irrigant Inadequate cool down period following Motor must be allowed to cool down following steam sterilization sterilization
19. face with a moist sterile towel If attachment continues to overheat Contact Customer Care Attachment telescoping tube is Attachment mishandled failed due to DO NOT use Contact Customer Care bent loose damaged or missing a extended use or excessive force applied component during use Dispose of telescoping tube Telescoping Tubes are multi use disposable Incorrect cleaning or sterilization Heavy side loading during dissection Use nomenclature markings on the attachment to match with a Color band on Attachment corresponding dissecting tool or Contact Customer Care Telescoping Tube fades or discolors Use of chlorine based or corrosive agents Aging Telescoping Tubes are multi use disposable Attachment has excess lubrication Wa during cleaning Visually inspect and wipe excess lubrication Attachment damaged by dissecting Footed attachment has a tool drilling out part or all of leg foot component missing from leg foot area DO NOT use Contact Customer Care area or foot is bent C er 2 o Qa Bend caused by incorrect use The contra angle attachment operates by a set of internal gears to engage the 16 Mf contra angle attachment is drive shaft It is normal for some heat overheating to be generated approximately 2 cm from the distal end of the attachment and at the right of the angle head Smoke is generated by the Attachment is not in the locked Make sure the attachment is in the locked positio
20. l Specifications Part No EM100 A Speed 200 75000 RPM forward reverse Size 9 02 cm length x 2 03 cm diameter Weight 180 g Duty Cycle To avoid overheating e For continuous use in operating room temperatures up to 40 C the Legend EHS Motor is rated for a cutting time of 3 minutes at 70 000 RPM e For normal operating room temperatures typically 20 C the Legend EHS Motor is rated for a continuous cutting time of 10 minutes followed by 25 minutes of rest e The Legend EHS Motor is rated for intermittent use of 20 seconds ON 20 seconds OFF indefinitely at 70 000 RPM Midas Rex Legend EHS Stylus Motor A smaller compact high speed high torque reversible electric motor used to dissect bone and biomaterials at selectable speeds from 200 to 75 000 RPM The Midas Rex Legend EHS Stylus Motor cable is integral with the Handpiece and is not removable from the motor A Midas Rex Legend EHS Stylus Motor B Cable C Rotational collet D Stationary collet E Ground connector F 4 pin connect G Locking sleeve H Black boot Technical Specifications Legend EHS Stylus Motor Part No EM200 Speed 200 75000 RPM forward reverse Size 7 77 cm length x 1 65 cm diameter Weight 90 g Duty Cycle To avoid overheating e For continuous use in operating room temperatures up to 40 C the Legend Stylus Motor is rated for 3 minutes at 60 000 RPM followed by 25 minutes of rest e For normal ope
21. n attachment or motor position A non Legend tool is being used Replace with a Legend tool Try another attachment or tube to isolate the location of the problem If the attachment is failing contact Customer Care If the tube is failing dispose of it and use a new tube Attachment tube and tool are not Match color code on the tool packaging to the color code on the compatible attachment tube Motor is damaged Contact Customer Care Tools size and geometry may Adjust the speed by changing the pressure setting or foot finger control contribute to flailing at certain speeds Do not use if flailing persists Change tool bol vbrteserasid Tools size and geometry may create Adjust the speed y excessive vibration at certain speeds Change tools Extended use Change to a new tool Tool dull Reprocessed tool was used Bounce tin t Clean the attachment or motor thoroughly according to the instructions Tool will not seat properly in the Debrisim collet of tachment or motor or attachment collet OLN If cleaning does not correct the problem contact Customer Care A non Legend tool is being used Replace with a Legend tool If heat continues or is excessive contact Customer Care Worn attachment or tube bearings Tool fails 19 MCB does not report that it is booted Power off Wait 10 seconds Power on If error persists within 5 seconds of AI telling it to start and System Error We Belin cal M S subseque
22. nt reattempts fail UI MCB Com Failure Max resends exceeded UI MCB Com Failure Get answer failed g UI MCB Com Failure No status message System Error dnd ae Mis 10 seconds Power on If error persists received call Technical Services 6 UI MCB Com Failure Serialization ID error 7 UI MCB Com Failure Timeout exception 8 NotUsd J JA2 J J4J NA NA LLL E jou stalled no transitions on opto Punip zi Stalled e oo eeu S WANA pump 2 Stalled sensor P ener in on port 1 first 12 pin Unrecogonized damaged handpiece plugged in on port 2 second 12 pin Hand Unrecogonized damaged handpiece plugged Ana piece in on port 3 4 pin Unrecogonized damaged handpiece plugged in on port 4 Skeeter Aa Stalled Handpiece Stalled 16 MCB motor overcurrent MCB motor overcurrent detected Motor Motor Overcurrent Motor Overcurrent UnP lug handpi jece and plug back in If error persists replace handpiece Foot Control Connection Unplug Foot Control and plug back in If error persists Unrecognized damaged FCU plugged in replace Foot Control or switch to manual control A finger control error has been detected Check that the control lever ring is properly seated in one of the four possible positions If error persists contact Medtronic support Press OK to use alternate control method Unplug handpiece and plug back in If error persists replace handpiece
23. opens If Attach Handpiece Attach Footpedal screen opens return to steps 4 and 5 9 Prime irrigation and cooling See Precaution P1 a Adjust clamp on the irrigation tubing to OPEN b Manually prime the clear drip chamber if used c Depress and release the prime button on the touch screen panel Verify o O run until all air has been purged out of the tubing 13 e Asmall amount of irrigant is observed flowing at the tip of irrigation device s e Pump s turns off 10 Confirm system operation Verify e Pedal Coolant Starts handpiece and coolant flow coolant pump continues to run for 1 minute after pedal is released e Pedal Irrigation Starts and stops the handpiece and irrigation flow At this step you should also verify that the characters on the SPEED display changed from white to yellow e Pedal Buttons Please refer to Multifunction Foot Control Unit 11 Depress the intraoperative button on the back of the console Verify e Starts and stops the handpiece irrigation and or coolant flow 12 Touch Screen Verify e Speed can be adjusted e Mode can be changed y e In oscillate and cut modes check e The Blade Position panel opens e The clockwise and counterclockwise buttons move the position indicator and blade in the appropriate direction 14 e Depressing the 180 button moves the position indicator and blade 180 e Flow rate for irrigation is adjustable P
24. ower Down 1 Turn power switch Off 2 Disconnect a Accessories b Suction irrigation and coolant tubing c Power cord 3 Discard disposables following health care facility guidelines on contaminated materials NOTE If any of these condition are different check your set up if still incorrect contact Customer Service Cleaning IPC Foot Control Unit and Endo Scrub 2 Footswitch e Do notimmerse or sterilize the units e Do not use alcohol other solvents or abrasive cleaners 1 Wipe down the IPC Foot Control Unit and Endo Scrub 2 Footswitch with a cloth dampened with a neutral enzymatic detergent pH 6 0 8 0 or phenol based disinfectant Non Slip Pad ONLY la Spray a neutral enzymatic detergent pH 6 0 8 0 or a phenol based disinfectant mixed to manufactures instructions directly onto foot pad 1b Allow the solution to remain in contact with the surface for approximately 10 minutes 1c Wipe the solution or disinfectant off the foot pedal until visually clean 2 Dry the units with a clean non abrasive cloth NOTE If debris is found under the Foot Control Units boot return for warranty service Console Specifications Functional Standards for Electric Systems ANSI Medical electrical equipment Part 1 General AAMI ES requirements for basic safety and essential performance 60601 1 Medical electrical equipment Part 1 General 60601 requirements for basic safety and essential perfo
25. rating room temperatures typically 20 C the Legend Stylus Motor is rated for continuous cutting indefinitely at 60 000 RPM 11 Midas Rex Legend EHS Stylus Touch Motor Range of motion Range of motion Telescoping Finger Rest pull out push in Finger Lever Finger Lever Safe Mode Switch Control Lever Ring Stationary Collet Rotational Collet Midas Rex Legend EHS Stylus Motor 12 pin Connector and Boot To Rotate the Finger Lever SFT OAH OO gt 1 Firmly push the Control Lever Ring forward and rotate slightly in a clockwise or counter clockwise direction as shown in figure 2 Continue rotating the finger lever until lever locks in new position Technical Specifications Legend EHS Stylus Touch Part No EM210 Speed 75 000 rpm forward reverse Size 15 26 cm length x 1 65 cm diameter Weight 130g DUE Cycle To avoid overheating For continuous use in operating room temperatures up to 40 C the Legend EHS Stylus Motor is rated for 3 minutes at 60 000 rpm followed by 25 minutes of rest e For normal operating room temperatures typically 20 C the Legend EHS Stylus Motor is rated for continuous cutting indefinitely at 60 000 rpm 12 Splash Screen The Splash Screen is displayed while the system is starting up and executing its self tests INTEGRATED POWER pe Mectironic inibalization m Progress Settings Screen During the boot up
26. rmance EN 1 IEC 60601 Medical Electrical Equipment Part 1 General 1 4 Requirements for Safety Part 4 Programmable Electrical Medical Systems 1 2 Electromagnetic Compatibility Requirements and Tests 2006 CSA C222 Medical Electrical Equipment Part 1 General 2005 No 601 1 Requirements for Safety Physical Dimensions Size 277 mm W x 353 mm H x 267 mm D Weight 7 3 kg Operational Environment Temperature 10 C to 33 C Humidity 30 to 75 RH Barometric Pressure 700 1060 hPa Transport and Storage Environment EN 60601 Medical Electrical Equipment Part 1 2 General 2001 Requirements for Safety Collateral Standard Al I 0601 Medical electrical equipment Part 1 General requirements for basic safety and essential performance Temperature 40 C to 70 C Humidity 10 to 95 RH Barometric Pressure 500 to 1060 hPa Display Touch Screen Type High contrast digital graphic Color visible in complete darkness Resolution Display 21 cm diagonal resolution 480 X 640 pixels Audio Output Baseline Audio Sound Level 60 dBA minimum SPL 1 m Electrical Input Voltage 100 V 240 V 10 Frequency 50 60 Hz Power Consumption 500 VA Auxiliary AC output 200 VA Max Internal Fuse 5x20 mm T L 5 A 250 V Medtronic Xomed P N 11270066 Duty Cycle for Applied Part Maximum on Time 120 Seconds Minimum off Time 180 Seconds Protectively Earthed Exposed Metal Applicable components Equalization
27. se Disposable Attachment NOTE IT IS IMPORTANT THAT THE OPERATOR BE FAMILIAR WITH THIS MANUAL AND THE USER S GUIDE WITH THEIR WARNINGS PRECAUTIONS PROCEDURES AND SAFETY ISSUES Foot pedal connector General Uppercase Alphabetic list A B C etc contain introductory information where Numeric list 1 2 3 etc are How To instructions Definitions Explaining the essential meaning of a word or acronym as used in this manual Also explains changes in words or phrases variations from one product generation to the next FCU Foot Control Unit IPC Integrated Power Console I V Intravenous NIM Nerve Integrity Monitor One or all of the following units NIM Response NIM Pulse NIM Response 2 0 NIM Pulse 2 0 NIM Neuro 2 0 NIM Response 3 0 NIM Pulse 3 0 NIM Neuro 3 0 Nomenclature Ihe act or process or an instance of naming Warnings and Precautions Warninc authorized Medtronic service facilit the enclosure is opened W3 The IPC contains live circuitry that can cause injury or death to operators or patients if assembled incorrectly This document and the documents referenced herein are not sufficient to guarantee correct assembly and operation of the device Product specific training and product specific test equipment is required to ensure the correct operation and assembly of the IPC WA This system requires insulated connectors for the StraightShot MA Microdebrider
28. t e utad cro c i rat Li vba RE Ertsd eis 10 Visao High Speed Otologic Drill Water Cooled 10 PCCM MIC Al SDSCHTCdl IPS coude eerste eeu NEEE ras E kaa 10 Skeeter Ultra Lite Oto Tool System Set Up and Use 10 Technical SPC TIC AION G sooo onte aeris a domes 10 Midas Rex Legend EIS MOT socer ie a tete 10 Technical SDecHIC AION Go aa 11 Midas Rex Legend EHS Stylus Motor cessus il Technical Specih AMONG AA 11 Io Rotate thie Finger LOVER ai 12 Technical aa 12 E nE ei a i ecoute tait d IUE abi d MM EE 12 eiu t STE I TNR E 12 Handpiece Detault Settings Table uestis estre bri bau 13 Console SETU T 13 Connect Handpiece Footswitch SCPOeEL us cementerio rota 13 Console Set Up Instructions asus sees etos tnter id th i teneo ti eoe rie taber auus 13 Power coo 14 Ql n 14 Console SDSOHICIUONS oaa ida ME bd oe eR I re 14 Serial Number Do not dispose of this product in the unsorted municipal waste stream Dispose of this product according to local regulations See http recycling Medtronic Com for instructions on proper disposal of this product Do not use if package is open or damaged e Package Contents Pump Head 1 Pump Head 2 2 O 1 T AGG accessory 0000 F Catalog Number RE Qe pum 0 Is approximately equal to SS Sterilized by radia
29. tes and monitors the nerve This system has connections that allow the NIM to be connected with the Visao handpiece and Stimulating Bur Guard enabling the NIM to stimulate and monitor the nerve at the surgical site he system can be used to clear the end of a rigid rod endoscope in order to maintain good visualization of endoscopic procedures without having to remove the scope from the surgical site his device is intended for use by physicians trained in the procedures described Sales and Customer Care Medtronic is committed to provide the highest standard of workmanship in manufacturing its products Your system requires minimal maintenance and calibration Servicing and or modification to the system or any accessory attachment by anyone other than qualified service personnel may significantly compromise the systems performance and void the equipment warranty For best performance it is recommended that all service be performed by Medtronic Xomed service personnel Medtronic recommends preventative maintenance and screen calibration scheduled at yearly intervals Comprehensive testing and calibration should be performed by returning the entire system to Medtronic Customer Service U S Customers Should your console or related equipment malfunction Medtronic provides at no charge loaner equipment shipped to your facility by UPS or Federal Express for use while your equipment is being serviced by Medtronic Please a
30. the pump by number with the cartridge number and or pump set up screen number listed on the touch screen When setting up the console these numbers must match Pump 2 Designator TE Not all Pump Cartridges have pump designator numbers Irrigation Coolant Pumps Pump Cartridge Set up he Pump Cartridge snaps onto the lower section of the pump 2 2 9 ae Visao Pump Cartridge The Visao Pump Cartridge has both a pump tube and a return tube B y a M Pump tubing Pump tubing is clipped into the Pump Cartridge Return tube Visao Coolant Pump Set Up The Pump Cartridge snaps onto the lower section of pump 1 Accessories attachments Multifunction Foot Control Unit FCU Part No 1898430 or EF200 Buttons and Pedal NOTE Each button must be depressed and held for a definable amount of time 100 mS by default Drills A Foot Pedal Start Stop Variable speed Aa Non Slip Foot Pad Right Button Pedal function Start Stop or Variable speed Top Button Active handpiece selection Left Button Mode selection FWD REV e Microdebrider A Pedal Start stop variable speed start stop or variable speed selectable via FCU button on Main Screen B Right Button In OSC Mode this button will rotate inner blade 60 180 touchscreen selected In FWD Mode this button will select Pedal function Start stop or variable speed C Top Button Active handpiece selection D Left
31. tion Do STERILE R not use if package is open or damaged sms Sterilized by ethylene oxide Do not use if package is open or damaged Authorized representative in the european communit This device complies with medical device directive 93 42 EEC Caution federal law U S A Restricts this device to sale by or on the order of a p Rx Only dB 00 NUNC Date of Manufacture ROHS Environmental friendly use period China SJ T11364 On Off main power ee Instrument Case Instrument case EO Lubricant Diffuser Lubricant Diffuser Do Dissecting Too Dissecting Tool Conforms to ANSI AAMI ES 60601 1 IEC EN 60601 1 Certified to CSA C22 2 No 601 1 TOE Handpiece II Skeeter handpiece EMC compliance mark EUR USA JPN AUS Protective Earth Equipotential NZ Consult instructions for use Attention see instructions for use IPX1 Bone Mill Bone Mill Motor Motor Brush Brush Protected against vertical water drops Protected against the effects IPX7 of temporary immersion in water Type BF applied part Manual Start Stop Co RF transmitter interference A may occur Precaution Pinch hazard Keep fingers clear of rollers STIM BUR connector NIM console connector Electrical high speed World Wide Standard for medical tubing diameter NENNMITTM Adapter Adapter TOOL Tool control TUBE Tube control Multi Use Disposable Attachment Multi U
32. traightShot M4 Microdebrider Part No 1898200T Midas Rex SC1 Part No ED100 Speed 50 5 000 RPM oscillate 50 12 000 RPM forward Size 14 3 cm length x 1 8 cm width 1898200T Weight 228 g 1898200T 240g 1897200 254g 1897200T 240g 1897201 he StraightShot M4 and SC1 Handpiece under full load are rated for intermittent operation per the following Maximum On Time 60 seconds Minimum Off Time 30 seconds NOTE If any of these condition are different check your set up if still incorrect contact Customer Service StraightShot Magnum Il and StraightShot III Microdebriders Duty Cycle Basic handpiece Suction barb Locking collar Cable i os Technical Specifications Handpiece StraightShot Magnum II Part No 1897200 StraightShot III Part No 1897201 Size 17 cm length x 1 6 cm diameter 1897200 Speed 50 5 000 RPM oscillate 50 12 000 RPM forward Size 17 cm length x 1 6 cm diameter Weight 240 g Duty Cycle Under full load are rated for intermittent operation per the following Maximum On Time 60 seconds Minimum Off Time 30 seconds Handpieces Drills Caution do not use Xcalibur or Powerforma handpieces with the IPC console Visao High Speed Otologic Drill Water Cooled A Handpiece 10 Cable Cable clip Cooling barbs Locking collar Technical Specifications Visao High Speed Otologic Drill Part No 3334800 MOO Speed 200 80 000 RPM forward reverse Water Cooled Size 16 0
33. x Legend EHS Motor and Legend EHS Stylus Motor Cable from motor or console on C EE 1 Push the cable towards the motor or console 2 Then pull out by locking ring A To Remove Midas Rex Legend EHS Stylus Cable from console Push the cable towards the console then pull by locking ring A To Remove cables multi pin with polymer insulating boots NOTE Confirm handpieces contain polymer insulating boot A If handpiece contain missing or cracked polymer boots contact Medtronic Customer Care for upgrade NOTE If units with polymer insulating boots have debris under the insulator e Reclean according to Cleaning and Sterilization instructions e lf debris was not removed return for warranty servicing See warning W4 1 Push the cable towards the console 2 Then pull out by the polymer insulating boot A To Remove cables multi pin with silicone insulating boots Silicone insulated connectors do not have a locking device ring and may be removed by pulling straight out on the connector Cable Disconnection single pin Single pin connectors do not have a locking device ring and may be removed by pulling straight out on the connector Console Rear D Pole clamp Compact flash card port factory use only Manual Start stop button Fuse Access Replace only with 5 x 20 T L 5A 250 V fuse Auxiliary power outlet with protective cover e For use at grid voltage lt 120 VA
Download Pdf Manuals
Related Search