iCarsoft AUTO OBDII/EOBD Scanner i810 User Manual in English..
Contents
1. 5 6 02 Sensor Monitoring Test OBD2 regulations set by SAE require that relevant vehicles monitor and test the oxygen 02 sensors to identify problems related to fuel efficiency and vehicle emissions These tests are not on demand tests and they are done automatically when engine operating conditions are within specified limits These test results are saved in the on board computer s memory The 02 Monitor Test function allows retrieval and viewing of 02 sensor monitor test results for the most recently performed tests from the vehicle s on board computer The 02 Monitor Test function is not supported by vehicles which communicate using a controller 32 iCarsoft i810 OBDII EOBD scanner area network CAN For 02 Monitor Test results of CAN equipped vehicles see chapter On Board Mon Test Select 02 Sensor Monitoring test in Diagnostic Menu and press 4l The screen will display as shown below Bank 1 sensor 1 MENU CE MA a E Press A T to select C and E to Page Press 4 to return and press to confirm Notes If the vehicle does not support the mode an advisory message will be displayed on the screen View test results of select 02 sensor 33 iCarsoft i810 OBDII EOBD scanner MENU Rich to lean sensor threshold voltage constant 2 52 V Low sensor voltage for switch t ime clculation constant 5 20 V BACK Press T to select C and2. ccc ccc cee eee eee 36 iCarsoft i810 OBDII EOBD scanner 1 Safety Precautions and Warnings To prevent personal injury or damage to vehicles and or the scan tool Read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle Always perform automotive testing in a safe environment Wear safety eye protection that meets ANSI standards Keep clothing hair hands tools test equipment etc Away from all moving or hot engine parts Operate the vehicle in a well ventilated work area Exhaust gases are poisonous Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests Use extreme caution when working around the ignition coil distributor cap ignition wires and spark plugs Theses components create hazardous voltages when the engine is running NEUTRAL for manual transmission and make sure the sparking brake is engaged Keep a fire extinguisher suitable for iCarsoft i810 OBDII EOBD scanner gasoline chemical electrical fires nearby e Don t connect or disconnect any test equipment while the ignition is on or the engine is running e Keep the scan tool dry clean free from oil water or grease Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary iCarsoft i810 OBDII EOBD scanner 2 General Information 2 1 On Board Diagnostics OBD II The first generation of
3. 6 Secondary air 7 Heated Catalyst 8 A C system 2 5 OBD II Monitor Readiness Statuses OBD II systems must indicate whether or not the vehicle s PCM s monitor system has completed testing on each component Components that have been tested will be reported as Ready or complete meaning they have been tested by the OBD II system The purpose of recording readiness states is to allow inspectors to determine if vehicle s OBD II system has tested all the components and or systems The power train control module PCM sets a monitor to Ready or Complete it will remain in this state A number of factors including erasing of diagnostic trouble codes DTCs with a scan tool or a disconnected battery can result in Readiness Monitors being set to Not ready Since the three continuous monitors are constantly evaluating they will be reported as iCarsoft i810 OBDII EOBD scanner Ready all of the time If testing of a particular supported non continuous monitor has not been completed the monitor status will be reported as Not Complete or Not Ready In order for the OBD monitor system to become ready the vehicle should be driven under a variety of normal operating conditions These operating conditions may include a mix of highway driving and stop and go city type driving and at least one overnight off period For specific information on getting your vehicle s OBD monitor
4. C to Page Press to return 5 7 Vehicle Information The Vehicle Info function enables retrieval of Vehicle Identification No VIN Calibration ID s Calibration Verification Nos CVNs and In use Performance tracking on 2000 and newer vehicles that support Mode 9 Select Vehicle information in the Diagnostic Menu and Press d The screen will display as shown below 34 iCarsoft i810 OBDII EOBD scanner MESSAGE VIN L23948AH98S973538 CALID L339EH150L3V5050 CVN F63F46B4 Press l to return data model Press 4 to return Diagnostic Menu 35 iCarsoft i810 OBDII EOBD scanner 6 Software update 1 Setup Update tools Put the CD in to PC and open you can see the setup file in the CD i Setup_V 3 0 exe gt Setup exe H weal Acresso Software Double click the Setup file to setup the tool Operate follow the instructions and finish to setup 36 iCarsoft i810 OBDII EOBD scanner iCarsoft tools InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successfully installed iCarsoft tools Click Finish to exit the wizard After finish setup there is an icon of scanner in desktop 2 Run the update tool and Operate in accordance with photographs 37 iCarsoft i810 OBDII EOBD scanner fie iCarsoft 3 0 Http www icarsoft us Http www icarsoft com _ ing Software Icarsoft Intelligent Technology Co Ltd All Righ
5. are intended to provide you with a guide as to where a fault might be occurring within a vehicle OBD II Diagnostic Trouble Codes consist of a five digit alphanumeric code The first character a letter identifies which control system sets the code The other four characters all numbers provide additional information on where the DTC originated and the operating conditions that caused it to set Here below is an example to illustrate the structure of the digits iCarsoft i810 OBDII EOBD scanner Sub systems 1 Fuel and Air Metering 2 Fuel and Air Metering 3 Ignition System or Engine Misfire 4 Auxiliary Emission Controls 5 Vehicle Speed Control and Idle 2 3 Location of the Data Link Connector DLC The DLC Data Link Connector or Diagnostic Link Connecter is the standardized 16 cavity connector where diagnostic scan tools interface is 12 inches from the center of instrument panel dash under or around the iCarsoft i810 OBDII EOBD scanner driver s side for most vehicles If Data Link Connector is not located under dashboard a label should be there telling location For some Asian and European vehicles the DLC is located behind the ashtray and the ashtray must be removed to access the connector if the DLC cannot be found refer to the vehicle s service manual for the location L 2 4 OBD II Readiness Monitors An important part of a vehicle s OBDII system the Readiness Monitors which are indicators u
6. On Board Diagnostics called OBD I was developed by the California Air Resources Board ARB and implemented in 1988 to monitor some of the emission control components on vehicles As technology evolved and the desire to improve the On Board Diagnostics system increased A new generation of On Broad Diagnostic system was developed This second generation of On Broad Diagnostic regulations is called OBD II The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions When a problem is detected the OBD II system turns on a warning lamp MIL on the vehicle instrument panel to alert the driver typically by the phrase of Check Engine or Service Engine Soon The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem Here below follow three pieces of such valuable information 1 Whether the Malfunction Indicator Light MIL is commanded on or off iCarsoft i810 OBDII EOBD scanner 2 Which if any Diagnostic Trouble Codes DTCs are stored 3 Readiness Monitor status 2 2 Diagnostic Trouble Codes DTCs OBD II Diagnostic Trouble Codes are codes that are stored by the on board computer diagnostic system in response to a problem found in the vehicle These codes identify a particular problem area and
7. can select one to review The last menu is clear all data 4 3 DTC LOOKUP Select DAIGNOSE REVIEW in the Main Menu and press ll The screen will display the interface as shown below DTC LOOKUP Please Input the DTC number P0100 UP DOWN Change LEFT RIGHT Select a a Enter the DTC number Lm and W use to change the DTC number af and pe use to Select press ll to confirm it will show the DTC description As shown below 22 iCarsoft i810 OBDII EOBD scanner P0100 Mass or volume air flow a circuit Press or 4 to return the Main menu 5 OBD II Diagnostics Select DIAGNOSE in Main Menu and press The screen will display a sequence of messages displaying the OBDII protocols will be observed on display until the vehicle protocol is detected if the scan tool fails to communication with the vehicle s ECU a ERROR message shows up on the display Communication error Please make sure 1 System equipped 2 Cable connect ok Maybe you can turn off the key then turn on the key and try again 23 iCarsoft i810 OBDII EOBD scanner When the scanner communicate with the vehicle the screen will display the Diagnostic Menu as shown below Read Trouble Code Erase Trouble Code I M Readiness Status OK g a l A Press T to select i and c to Page and press 4l to confirm 5 1 Read Trouble Code Reading Codes can be done w
8. d methods for stopping the test once it has been started Before starting the Component Test refer to the vehicle service manual for instructions to stop the test select Component Test in the Diagnostic Menu and press al to enter the activation function If the ECU support the function the screen will show as below Evaporative system leak test press to confirm the screen will display the 30 iCarsoft i810 OBDII EOBD scanner relative information about EVAP system Some vehicles manufacturers do not allow external devices to control vehicles system If the car support this function It may display as below MESSAGE Operation is successful Press 4l to return data model Press 4 to return 5 5 Freeze Frame Data When an emission related fault occurs certain vehicle conditions are recorded by the on board computer This information is referred to as freeze frame data freeze Frame data is a snapshot of the operating conditions at the time of an emission related fault select Freeze Frame Data in the Diagnostic Menu and press 4 l the screen will display the interface as shown below 31 iCarsoft i810 OBDII EOBD scanner DTC that caused required freeze frame data storage P0602 Fuel System 1 Status ON 60 Engine RPM T Intake Manifold Absolute Pressu re 121 kPa GRAPH 1 1 BACK Press C4 T to select 4 and C to Page Press 4 to return and press 4 to confirm
9. iCarsoft i810 OBDII EOBD scanner INDEX 1 Safety Precautions and Warnings ceeeees 3 2 General Information 6442 04 00 ccs 2 4d 4G be bad ta Coes 5 2 1 On Board Diagnostics 0BD II 5 2 2 Diagnostic Trouble Codes DTCs 0 6 2 3 Location of the Data Link Connector DLC 7 2 4 OBD II Readiness Monitors 8 2 5 OBD II Monitor Readiness Statuses 10 2 6 OBD II Definitions 0 eee 11 3 Using the Sean Tooli casce ew sh see es teeeancerciwars 14 3 1 Tool Description eet een enrenar iiaa k iaa 14 3 2 Specifications reee Saw eee ed re wwe SAS 15 3 3 Accessories Include cece cee ee eee 15 3 4 Product Troubleshooting 00 cee eeee 15 4 Software Function 0 ccc cee eee eee eee 17 4 1 System Configuration ccc eee 18 4 2 DIAGNOSTIC REVIEW 0 cee ee eee 21 4 3 DTC LOOKUP set os oo fre ea See a a e ae eal 22 5 OBD II Diagnostics 0 ccc eee 23 5 1 Read Trouble Code oc e cod ot caiivesetadsutusiesaked 24 5 2 Erasing CodeS ccc eee ce ee cece ees 26 iCarsoft i810 OBDII EOBD scanner 5 3 Read Datastreaict inos ven cia essa evea tases ee bee 28 5 4 Component teSt cece cc eee ee eee eee ees 30 5 5 Freeze Frame Data cece eee eee eee eee 31 5 6 02 Sensor Monitoring Test 0000 32 5 7 Vehicle Information sssssusssssuussssess 34 6 Software update
10. icles and for each monitor in any particular vehicle OBD II Drive Cycle A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the ready condition The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnosis Some form of a drive cycle needs to iCarsoft i810 OBDII EOBD scanner be performed after DTCs have been erased from the PCM s memory or after the battery has been disconnected Running through a vehicle s complete drive cycle will set the readiness monitors so that future faults can be detected Drive cycles vary depending on the vehicle and the monitor that needs to be reset For vehicle specific drive cycle consult the vehicle s Owner s Manual 7 Freeze Frame Data When an emissions related fault occurs the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to _ help identifying the problem This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM vehicle speed air flow engine load fuel pressure fuel trim value engine coolant temperature ignition timing advance or closed loop status iCarsoft i810 OBDII EOBD scanner 3 Using the Scan Tool 3 1 Tool Description iCarsoft p Eoft DLC Data Link Connector DLC Use to connect the scan tool t
11. ith the key on engine off KOEO or with the key on engine running KOER Stored Codes are also known as hard codes or permanent codes These codes cause the control module to illuminate the malfunction indicator lamp MIL when emission related fault occurs Pending Codes are also referred to as maturing codes or continuous monitor 24 iCarsoft i810 OBDII EOBD scanner codes They indicate problems that the control module has detected during the current or last driving cycle but are not considered serious yet Pending Codes will not turn on the malfunction indicator lamp MIL If the fault does not occur within a certain number of warm up cycles the code clears from memory select Read Trouble Code and press in Diagnostic Menu If there are some codes the screen will display the codes as show below Read Current Code Read Pending Code Read Permanent Code BACK According to the above figure to select different item by pressing T and press 4 to confirm 25 iCarsoft i810 OBDII EOBD scanner P0602 Control Module Programmi ng error P0614 ECM TCM Incompatible Press or 4 to return the Diagnostic menu View DTCs and their definitions on screen If there are no Diagnostic Trouble Codes present the display indicates No Trouble Code Wait a few seconds or press any OK to return to Diagnostic Menu The control module number sequence of the DTCs t
12. o the vehicle 2 LCD DISPLAY Indicates test results Color 14 iCarsoft i810 OBDII EOBD scanner 320 x 240 pixel display with contrast adjustment KEY BROAD include 4 Y 44 gt 4 HELP 4 USB PORT Use to connect the scan tool to PC 3 2 Specifications A Display Color 320 x 240 pixel display with contrast adjustment B Operation Temperature 20 C 75 C C Storage Temperature 40 C 120 C D Power 8V 24V E Dimensions Length Width Height 135 mm 85 mm 26 mm F Weight Net Weight 250 g Gross Weight 450 g 3 3 Accessories Include A User s Manual Instructions on tool operations B CD Include User s Manual Update Software and etc C USB Cable Used to upgrade the scan tool 3 4 Product Troubleshooting Vehicle Linking Error iCarsoft i810 OBDII EOBD scanner A communication error occurs if the scan tool fails to communicate with the vehicle s ECU Engine Control Unit You need to do the following to check up A Verify that the ignition is ON B Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC C Verify that the vehicle is OBD2 compliant D Turn the ignition off and wait for about 10 seconds Turn the E Ignition back to on and continue the testing F Verify the control module is not defective Scan tool doesn t power up If the scan tool won t power up or operates inc
13. orrectly in any other way you need to do the following to check up A Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC B Check if the DLC pins are bent or broken Clean the DLC pins if necessary C Check vehicle battery to make sure it is still good with at least 8 0 volts iCarsoft i810 OBDII EOBD scanner 4 Software Function CATION Don t connect or disconnect any test equipment with ignition on or engine running 1 Turn the ignition off 2 Locate the vehicle s 16 pin Data Link Connector DLC 3 Plug into the scan tool cable connector to the vehicle s DLC the scan tool will be light As shown below i810 icarsoft Technology Inc All Rights Reserved Http Awww icarsoft us D Http www icarsoft com 4 Turn the ignition on Engine can be off or running 5 Click any key to enter the Main Menu iCarsoft i810 OBDII EOBD scanner DIAGNOSE SYSTEM CONFIGURATION DIAGNOSE REVIEW DTC LOOKUP OK 1 1 BACK USE the key T to select in the Main Menu and press i to select 4 1 System Configuration Select SYSTEM CONFIGUARATION in the Main Menu and press 4l The screen will display the interface as shown below LANGUAGE SETUP SYSTEM INFORMATION BEEPER UNIT OF MEASURE HE S a 7 a The scanner allows you to make the following adjustments iCarsoft i810 OBDII EOBD scanner and settings 1 LANGUAGE SETUP Select
14. otal number of codes detected and type of codes Generic or Manufacturer specific will be observed on the upper right hand corner of the display 5 2 Erase Trouble Codes CAUTION Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle s on board computer but also Freeze Frame data and manufacturer specific enhanced data Further the I M Readiness Monitor Status for all vehicle 26 iCarsoft i810 OBDII EOBD scanner monitors is reset to Not Ready or Not Complete status Do not erase the codes before the system has been checked completely by a technician This function is performed with key on engine off KOEO Do not start the engine select Erase Trouble Code and press in Diagnostic Menu the screen will display the interface as shown below MESSAGE fault codes is erased Bi A Press or 4 to return the Diagnostic menu Notes Before performing this function Make sure to retrieve and record the trouble codes After clearing you should retrieve trouble codes once more or turn ignition on and retrieve codes again If there are still some trouble codes for hard troubles please find the reason caused the trouble code firstly and then solve the problem Now the trouble codes can be erased 27 iCarsoft i810 OBDII EOBD scanner 5 3 Read DataStream The Read DataStream function allows viewing of live or
15. real time PID data of vehicle s computer module s Press de T to select Read DataStream in Diagnostic Menu and press to confirm The screen will display the interface as shown below Display All Datastream Manually Select DataStream ar BACK Press T to select dy and r to Page and press to confirm Notes You can select show all datastream or only show the datastream which was selected by you Select Display All Datastream and Press to enter datastream data model the screen will display the interface as below 28 iCarsoft i810 OBDII EOBD scanner Data model DTCs Stroed in this ECU 1 Fuel System 1 Status ON Engine RPM 760 Intake Manifold Absolute Pressu re 121 kPa GRAPH 1 1 BACK If appear GRAPH Press 4 i to enter Graph mode Press to return Diagnostic Menu the screen will display the interface as below Graph model DATASTREAM Intake Manifold Absolute Pressu 121 kPa 0 3 6 9 12 15 18 21 24 DATA 1 1 BACK Press l to return data model Press 4 to return 29 iCarsoft i810 OBDII EOBD scanner DIAGNOSTIC MENU 5 4 Component test The Component Test function allows initiating a leak test for the vehicle s EVAP system The scan tool itself does not perform the leak test but commands the vehicle s on board computer to start the test Different vehicle manufacturers might have different criteria an
16. rite bootdb bin 0K Erase diag bin 0K Write diag bin OK UPDATA FINISH M Update success BERRRRRRRRRRRRRRRERRRRRRRR RRR N Updating Softwar Icarsoft Technology Inc All Rights Reserved USB CONNECTED If update success the software wil display Update success if update not success it will display Update fail Try again Press finish the scanner is already updated and you can unplug the scanner from PC 42
17. s desired language Choose LANGUAGE and press ll The screen will display the interface as shown below 1 1 ENGLISH SIMPLIFIED CHINESE TRADITIONAL CHINESE GERMAN SPANISH OK M O You can press k F key to choose the different Language and then press i to confirm The system will Convert to the chosen language interface at once 2 SYSTEM INFORMATION show the system information Choose SYSTEM INFORMATION and press The screen will display the interface as shown below iCarsoft i810 OBDII EOBD scanner Serial Number 181000012302 Hardware Ver 1 0 Software OBD Software ver V2 8 SW date 2012 03 26 Press or 4 to return the Main menu 3 BEEPER ON OFF the beep Choose BEEPER and press the screen will display the interface as shown below Press C4 T to select and press to confirm 4 UNIT OF MEASURE change the units display mode 20 iCarsoft i810 OBDII EOBD scanner Choose UNIT OF MEASURE and press 4 the screen will display the interface as shown below METRIC UNITS ENGLISH UNITS Press ay T to select and press to confirm 4 2 DIAGNOSTIC REVIEW Select DAIGNOSE REVIEW in the Main Menu and press ll The screen will display the interface as shown below 21 iCarsoft i810 OBDII EOBD scanner Press pay T to select and press to confirm There are three menu for select Each menu save the data you
18. sed to find out if all of the emissions components have been evaluated by the OBD II system They are running periodic tests on Ca specific systems and components to ensure that they are performing within allowable limits iCarsoft i810 OBDII EOBD scanner Currently there are eleven OBD II Readiness Monitors or I M Monitors defined by the U S Environmental Protection Agency EPA Not all monitors are supported by all vehicles and exact number of monitors in any vehicle depends on the motor vehicle manufacturer s emissions control strategy Continuous Monitors Some of the vehicle components or systems are continuously tested by the vehicle s OBD II system while others are tested only under specific vehicle operating conditions The continuously monitored components listed below are always ready 1 Misfire 2 Fuel System 3 Comprehensive Components CCM Once the vehicle is running the OBD II system is continuously checking the above components monitoring key engine sensors watching for engine misfire and monitoring fuel demands Non Continuous Monitors Unlike the continuous monitors many emissions and engine system components require the vehicle to be operated under specific conditions before the monitor is ready These monitors are termed non continuous monitors and are listed below 1 EGR System iCarsoft i810 OBDII EOBD scanner 2 02 Sensors 3 Catalyst 4 Evaporative System 5 02 Sensor Heater
19. system ready please consult your vehicle owner s manual 2 6 OBD II Definitions Power train Control Module PCM OBD II terminology for the on board computer that controls engine and drive train Malfunction Indicator Light MIL Malfunction Indicator Light Service Engine Soon Check Engine is a term used for the light on the instrument panel It is to alert the driver and or the repair technician that there is a problem with one or more of vehicle s systems and may cause emissions to exceed federal standards If the MIL illuminates with a steady light it indicates that a problem has iCarsoft i810 OBDII EOBD scanner been detected and the vehicle should be serviced as soon as possible Under certain conditions the dashboard light will blink or flash This indicates a severe problem and flashing is intended to discourage vehicle operation The vehicle onboard diagnostic system can not turn the MIL off until necessary repairs are completed or the condition no longer exists DTC Diagnostic Trouble Codes DTC that identifies which section of the emission control system has malfunctioned Enabling Criteria Also termed Enabling Conditions They are the vehicle specific events or conditions that must occur within the engine before the various monitors will set or run Some monitors require the vehicle to follow a prescribed drive cycle routine as part of the enabling criteria Drive cycles vary among veh
20. ts Reserved a Use the USB cable to connect i810 scanner with PC b Run the update software When the scanner is connected with PC the software will show USB CONNECTED As below 38 iCarsoft i810 OBDII EOBD scanner fe iCarsoft 3 0 Http www icarsoft us Http www icarsoft com Updating Software lcarsoft Technology Inc All Rights Reserved USB CONNECTED 39 iCarsoft i810 OBDII EOBD scanner Htto www icarsoft us Look in Bo Database 518 E ICARSOFT_V3 0_CN BIN File name Files of type Bin Files bin Updating S Software Icarsoft Technology Inc All Rights Reserved 1 Click Update button 2 Select update file and click open button 3 Into the upgrade interface wait for the end of upgrade WARNNING Do not power off during upgrade Do not Plug or Unplug USB tools during upgrade 40 iCarsoft i810 OBDII EOBD scanner Start Update Waiting for a few minutes The software will update the scanner tool E aac Initializing WARNNING Erase BOOT HEX 0K Do not power off Write BOOT HEX during upgrade Thank you iting Softwar a lcarsoft Technology Inc All Rights Reserved USB CONNECTED Finish Update When the update is finished the screen on PC will show as below 41 iCarsoft i810 OBDII EOBD scanner Initializing Erase BOOT HEX 0K Do not power off Write BOOT HEX 0K during upgrade Erase bootdb bin OK Thank you W
Download Pdf Manuals
Related Search