INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
Contents
1. Photo D Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature 2011 Dorman Products Inc No reproductions in whole or in part without prior written approval INSTALL RAVIOVALI NS TRUCTI ONS WINDOW REGULATOR ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualified technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully Prior to Installing New Window Regulator STEP 1 Make sure that glass sashes are in good condition and are properly affixed to the windo2. INSTALL RAVIOVALI NS TRUCTI ONS WINDOW REGULATOR ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualified technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully General Tech Tips Use painter s tape rather than duct tape to secure window It will not damage paint or leave sticky residue A plastic pry tool is useful It will not easily damage delicate trim like a screwdriver or metal pry bar The replacement regulator should have a liberal amount of grease on slide area If there is not much grease present white lithium grease works well to lubricate the slide area Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly Window run channels should be cleaned and lubricated before installation of a new window regulator assembly Silicone spray works well NOTE Disconnecting the negative battery cable is always recommended for safety reasons Be certain that you know the implications of disconnecting the battery before doing so For example radio code information clock and radio settings PCM relearn OBD II readiness monitor reset Window Regulator Removal STEP 1 Gain access to t
3. ce with such standards and that you do not disable any motor vehicle safety feature 2011 Dorman Products Inc No reproductions in whole or in part without prior written approval INSTALL RAVIOVALI NS TRUCTI ONS WINDOW REGULATOR ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualified technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully Sector Gear Scissor Style Regulator NOTE This regulator style typically contains a highly tensioned spring that can become a dangerous projectile if not removed with care The sector gear must be secured prior to removing the motor STEP 1 Secure gear plate to mounting bracket by drilling a hole through the center of the gear and gear plate and installing a bolt and nut to hold them together Photo Photo F F STEP 2 Remove screws bolts or rivets and detach motor from bracket and gear STEP 3 Check motor for obvious signs of wear STEP 4 Reattach motor to regulator Window Regulator Installation STEP 1 Set regulator into door and attach with proper hardware STEP 2 Maneuver glass and regulator together to match up mounting points STEP 3 Attach glass to regulator STEP 4 Plug in switch temporar
4. he window regulator by removing the interior trim panel STEP 1a The interior trim panel is typically held to the door using a variety of screws an or hidden panel retainers Photo A Metal screws are usually used to secure the handle area to the door Photo B Look for screws under reflectors and trim pieces Remove all screws Disconnect any electrical connections and if necessary remove switch Photo A from panel Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature 2011 Dorman Products Inc No reproductions in whole or in part without prior written approval INSTALL RAVIOVALI NS TRUCTI ONS WINDOW REGULATOR ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this
5. ily and run window up and down to ensure that it moves freely STEP 5 Replace plastic water barrier sheeting STEP 6 Check trim panel retainers for brittleness and replace as necessary STEP 7 Replace trim panel switch and anything else removed Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature 2011 Dorman Products Inc No reproductions in whole or in part without prior written approval
6. part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualified technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully STEP 1b Once all of the screws are removed and electrical plugs are disconnected unsnap the panel retainers from the bottom of the door using a suitable tool Photo C Remove the trim panel by pulling the bottom away from the door while lifting the top of the panel off of the door STEP 1c Peel back the plastic water barrier sheeting enough to be able to remove the regulator STEP 2 Remove window regulator from door STEP 2a The window regulator will be fixed to the door using bolts or rivets The regulator will usually be attached to the window glass sashes with bolts Before removing any bolts or rivets be sure to have method to secure glass from dropping STEP 2b Remove bolts or rivets Rivets can be removed by drilling the center of each out or by knocking the heads off with a chisel and pushing the rivet out Photo D It may be necessary to maneuver the glass up or down to gain access to the bolts that hold the regulator to the glass If the glass cannot be moved it may be necessary to unbolt the regulator from the door first Make sure that the glass is properly supported STEP 2c Disconnect plug from motor and remove regulator from door
7. w glass STEP 1a It may be necessary to replace the sashes if they are damaged or old glue buildup is excessive Photo E If re gluing is necessary make sure to use appropriate adhesive Photo E STEP 2 Check window run channels for bends or weather stripping that is in poor condition Replace as necessary STEP 3 Lube rubber run channels with spray silicone lubricant STEP 4 Make sure door drain holes are clear so that moisture does not buildup in door If Original Motor is Being Reused Removing Installing Motor From To Regulator Cable Style Regulator STEP 1 Remove screws boils or rivets and detach motor from spool STEP 2 Check motor for obvious signs of wear STEP 3 Replace if necessary with new motor STEP 4 Reattach motor to regulator Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualified auto technician before attempting to perform any work you are not qualified to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffic Safety Administration Be sure that your work is performed in accordan
Download Pdf Manuals
Related Search