Home

P9000™ XDT

1. 1 Position wheelchair as close as possible to the desired object 2 Point the front and rear casters rearward to create the longest possible wheelbase 3 Reach back only as far as your arm will extend without changing your sitting position FIGURE 3 3 Reaching and Bending Backward P9000 XDT 24 Part No 1118386 SECTION 4 SAFETY INSPECTION TROUBLESHOOTING SECTION 4 SAFETY INSPECTION TROUBLESHOOTING NOTE Every six 6 months or as necessary take your wheelchair to a qualified dealer for a thorough inspection and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair To operate properly and safely your wheelchair must be cared for just like any other vehicle Routine maintenance will extend the life and efficiency of your wheelchair Safety Inspection Checklists A CAUTION As with any vehicle wheels and tires should be checked periodically for cracks and wear and should be replaced as necessary Initial adjustments should be made to suit your personal body structure needs and preference Thereafter follow these maintenance procedures Inspect Adjust Initially Q Ensure that the wheelchair rolls straight no excessive drag or pull to one side Ensure that all fasteners on the clothing guards are secure Q Ensure that the arms are secure but easy to release and adjustment levers engage properly Ensure that adjustable height arms operate and loc
2. A NEGATIVE BLACK battery cable ring terminal between the mounting plate and battery clamp of NEGATIVE battery terminal post POSITIVE RED battery cable ring terminal between the mounting plate and battery clamp of POSITIVE battery terminal post Secure the battery cable s ring terminal s to the battery clamp s BLACK to NEGATIVE and RED to POSITIVE with existing hex screws as shown in Detail A of FIGURE 11 9 Securely tighten Verify battery cable ring terminal s are correctly installed and securely tightened Slide battery clamp covers down battery cables and onto battery terminals as shown in Detail B of FIGURE 11 9 Using 11 inch long tie wraps secure each terminal cap in place as shown in Detail B of FIGURE 11 9 NOTE It will be necessary to trim excess tie wrap in order to install the battery box top s 8 Install the battery box top s 9 Install the battery box es into the wheelchair Refer to Removing Installing the Battery Boxes on page 50 NOTE New battery ies MUST be fully charged BEFORE using otherwise the life of the battery ies will be reduced 10 If necessary charge the battery ies Refer to Charging Batteries on page 48 P9000 XDT 58 Part No 1118386 SECTION BATTERIES Exploded View POSITIVE Hex Screw RED Cable Mounting Plate T Clamp NEGATIVE POSITIVE BLACK Cable Terminal Post NEGATIVE Terminal Post Grou
3. ADDRESSEE INVACARE CORPORATION CRM DEPARTMENT 39400 TAYLOR PARKWAY ELYRIA OH 44035 9836 Invacare Product Registration Form Please Seal with Tape Before Mailing NO POSTAGE NECESSARY IF MAILED INTHE UNITED STATES Cut Along Line SPECIAL NOTES SPECIAL NOTES WARNING CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE WHEELCHAIR USER As a manufacturer of wheelchairs Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user However final selection of the type of wheelchair to be used by an individual rests solely with the user and his her healthcare professional capable of making such a selection WHEELCHAIR TIE DOWN RESTRAINTS AND SEAT RESTRAINTS Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a wheelchair in a moving vehicle of any type It is Invacare s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made available by the auto industry Invacare cannot and does not recommend any wheelchair transportation systems As regards
4. AFTER JULY 4 1975 This warranty is extended only to the original purchaser user of our products This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state With regards to the original purchaser user only Invacare warrants the front and rear frames to be free from defects in materials and workmanship for a period of three 3 years from date of purchase seat frame for a period of three 3 years from the date of purchase electronics motors and gearboxes for a period of one 1 year from the date of purchase all remaining components for one 1 year from the date of purchase except upholstered materials padded materials and tires wheels If within such warranty period any product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the bottom of the back cover Provide dealer s name address date of purchase indicate nature of the defect and if the product is serialized indicat
5. Pivot both forks and casters to top of their arc simultaneously D Let casters drop to bottom of arc wheels should swing once to one side then immediately rest ina straight downward position perc Cover Locknut E Adjust locknuts according to gt o freedom of caster swing Nylon J Washer 3 Test wheelchair for maneuverability 4 Readjust locknuts if necessary and Caster repeat STEPS 1 3 until correct 5 Snap dust cover into the caster headtube Caster FIGURE 10 1 Adjusting Forks P9000 46 Part No 1118386 SECTION BATTERIES SECTION BATTERIES A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that on off switch on the joystick is in the off position When to Charge Batteries NOTE For this procedure refer to FIGURE 11 1 Recharge the batteries frequently Do not wait until the battery charge is low to recharge A battery s life is extended if the charge level is maintained well above a low condition The information gauge is the primary source of user feedback The true state of battery charge notification is as follows e Any GREEN LED lit Batteries are at full or well charged e Only AMBER and RED LEDs lit Batteries are moderately charged Recharge before undertaking a long
6. Reprogramming the controller reduces the stability control of the wheelchair Other program settings could cause the wheelchair to tip over resulting in serious injury to the user and or damage to the surrounding property If any indi vidual other than a qualified technician performs any work on these units the war ranty is void Operating Information Performance adjustments should only be made by professionals of the healthcare field or persons fully conversant with this process and the driver s capabilities Incorrect settings could cause injury to the driver bystanders damage to the chair and to surrounding property After the wheelchair has been set up check to make sure that the wheelchair performs to the specifications entered during the set up procedure If the wheelchair does not perform to specifications turn the wheelchair off immediately and reenter set up specifications Repeat this procedure until the wheelchair performs to specifications ALWAYS shift your weight in the direction you are turning DO NOT shift your weight in the opposite direction of the turn Shifting your weight in the opposite direction of the turn may cause the inside drive wheel to lose traction and the wheelchair to tip over DO NOT shift your weight or sitting position toward the direction you are reaching as the wheelchair may tip over DO determine and establish your particular safety limits by practicing bending reaching and transferring activi
7. SECTION 3 SAFETY HANDLING OF WHEELCHAIRS Safety and Handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair It is important to practice and master these safe techniques until you are comfortable in maneuvering around the frequently encountered architectural barriers Use this information only as a basic guide The techniques that are discussed on the following pages have been used successfully by many Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual Invacare recognizes and encourages each individual to try what works best for him her in overcoming architectural obstacles that they may encounter However all warnings and cautions given in this manual MUST be followed Techniques in this manual are a starting point for the new wheelchair user and assistant with safety as the most important consideration for all Stability and Balance A WARNING ALWAYS wear your seat positioning strap The seat positioning strap is a positioning belt only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear belt MUST be replaced immediately To assure stability and proper operation
8. immediately Always verify that hand grips on the rear cane are secure prior to use when an assistant is used to propel or lift the chair Check for any signs of looseness or deterioration and if found contact a qualified technician Do not attempt to move the wheelchair by using the hand grips if they are found to be unsecure or have deteriorated When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water Verify that grips are dry prior to use Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly Failure to observe this warning may result in injury to the user or bystanders DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H blocks Before performing any maintenance adjustment or service verify that On Off switch on the joystick is in the Off position Avoid storage or use near external flame or combustible products Tire Pressure DO NOT use your wheelchair unless it has the proper tire pressure P S I DO NOT overinflate the tires Failure to follow these suggestions can cause the tire to explode and cause bodily harm The recommended tire pressure is listed on the side wall of the tire Electrical Accessories EXTREME care should be exercised when using oxygen in close proximity to electric circuits and other combustible materials Contact your oxygen sup
9. may result NOTE For this procedure refer to FIGURE 11 3 NOTE To remove the battery boxes from the wheelchair reverse the following procedure 1 Verify that the on off switch on the joystick is in the off position 2 Place the front battery box onto the battery tray and connect controller connector to the front battery box Refer to Electronics Manual P N 1110532 Slide front battery box toward the front of the wheelchair p P9000 XDT 50 Part No 1118386 SECTION BATTERIES 4 Place rear battery box onto the battery tray and connect the rear battery box to the front battery box 5 Connect the front battery box to the controller A WARNING The battery box retaining strap MUST be fastened securely and adjusted prop erly to hold battery boxes in place before using the wheelchair 6 Connect the battery box retaining strap clip together and adjust if necessary Installing Removing Battery Tray NOTE For this procedure refer to FIGURE 11 4 To Controller Front Battery Battery Box Connectors Tray A Rear Battery Front f Box Connector Battery 6 rJ Rear Retaining Battery Strap Box L1 Retaining Strap Clip FIGURE 11 3 Removing Installing the Battery Boxes NOTE To remove the battery tray from the wheelchair reverse the following procedure 1 Attach the key slot bracket located at the front of the battery
10. of FIGURE 11 7 depending on battery type A NEGATIVE BLACK battery cable to NEGATIVE battery terminal post B POSITIVE RED battery cable to POSITIVE battery terminal post Secure the battery cable s ring terminal s to the battery terminal s post s BLACK to NEGATIVE and RED to POSITIVE with the provided 1 4 20 x 7 8 inch hex flange screw and hex flange locknut as shown in Detail A or Detail of FIGURE 11 7 depending on battery type Securely tighten x gt Verify all battery cable s ring terminal s are correctly installed and securely tightened Slide terminal cap s down battery cable s and onto battery clamps 6 Using the 11 inch long tie wrap secure each terminal cap in place Detail A or Detail B of FIGURE 11 7 NOTE It will be necessary to trim excess tie wrap in order to install the battery box top s 7 Install the battery box top s Part No 1118386 55 P9000 XDT SECTION BATTERIES Detail Dual UI Batteries 1 4 20 x 7 8 Inch NEGATIVE NEGATIVE Hex Flange Screw 6 Terminal Post POSITIVE Terminal Post GREY Terminal Post Terminal POSITIVE Yn 114 20 Terminal Post Hex Flange Locknut CONNECT CABLE RING 7 TERMINAL 1 THIS SIDE OF Terminal Cap TERMINAL POST Detail Dual Group 22 NF Batteries POSITIVE Terminal Post 1 4 20 x 7 8 Inch Hex Flang
11. of your wheelchair you must at all times maintain proper balance Your wheelchair has been designed to remain upright and stable during normal daily activities as long as you do not move beyond the center of gravity DO NOT lean forward out of the wheelchair any further than the length of the armrests Coping With Everyday Obstacles Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair Keep in mind your center of gravity to maintain stability and balance While the walking beam allows you to traverse up to a 2 inch bump or threshold stopping after the wheels cross the bump poses a problem The chair cannot reverse over the bump at this point Continue forward and then turn around Part No 1118386 19 P9000 XDT SECTION 3 SAFETY HANDLING OF WHEELCHAIRS While the P9000 XDT is designed for use primarily in and around the home the provider should determine whether this chair is suitable for the actual environment the chair will be used in DO NOT go down ramp at full speed Some seat back positions will cause wheelchair to feel unstable A CAUTION Be aware of condition of ramp Traction will be diminished nonexistent on a slip pery surface Proceed with caution A Note to Wheelchair Assistants When assistance to the wheelchair user is required remember to use good body mechanics Keep your back straight and bend your knees whenever tilting wheelchair or tr
12. purchased an Invacare product because Price L Features list features 5 Who referred you to Invacare products check all that apply L Doctor Therapist Friend Relative Dealer Provider Other L Advertisement circle one TV Radio Magazine Newspaper No Referral 6 What additional features if any would you like to see on this product Fold 7 Would you like information sent to you about Invacare products that may be available fora here particular medical condition 4 Yes No If yes please list any condition s here and we will send you information by email and or mail about any available Invacare products that may help treat care for or manage such condition s 8 Would you like to receive updated information via email or regular mail about the Invacare home medical products sold by Invacare s dealers L1 Yes LI No 9 What would you like to see on the Invacare website 10 Would you like to be part of future online surveys for Invacare products Yes LI No User s Year of birth If at any time you wish not to receive future mailings from us please contact us at Invacare Corporation CRM Department 39400 Taylor Parkway Elyria OH 44035 or fax to 877 619 7996 and we will remove you from our mailing list To find more information about our products visit www invacare com Fold here Fold here BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 196 ELYRIA OH POSTAGE WILL BE PAID BY
13. sag Replace if necessary Ensure seat release latch is not worn Replace if necessary Seat and or back upholstery have no rips and do not sag Replace if necessary Clean upholstery and armrests P9000 26 Part No 1118386 SECTION 4 SAFETY INSPECTION TROUBLESHOOTING Q Inspect charger AC power cord for damage Replace if necessary Troubleshooting Mechanical Chair Sluggish Casters Squeaks Veers Turn Performance Flutter and Left Right Rattles Looseness Chair 3 Solutions In Chair Wheels If pneumatic check tires for correct and X equal pressure Check for loose stem X nuts bolts Troubleshooting Guide SYMPTOM PROBABLE CAUSE Batteries draw excessive Battery failure current when charging Electrical malfunction Check that both casters contact ground at the same time SOLUTIONS Have batteries checked for shorted cell Replace if necessary Contact dealer Invacare for service Battery indicator flashes the Battery failure charge level is low immedi ately after recharging Charger malfunction Electrical malfunction Check batteries for shorted cell Replace if nec essary Contact dealer Invacare Poor connections between charger and wheel chair Contact dealer Invacare for service Battery indicator flashes the Batteries not charged charge level is low too soon Weak batteries after being recharged Electrical malfunction Have c
14. the swingaway footrest assembly off of the hinge pins Using 1 To move the footrest out of the way without removing push the footrest release lever inward rotate footrest outward 2 To lock the footrest push the swingaway footrest assembly towards the inside of the wheelchair until it locks into place NOTE The footplate will be on the inside of the wheelchair when locked in place Adjusting the Footrest Height NOTE For this procedure refer to FIGURE 6 2 NOTE This procedure applies to the swingaway footrest and elevating legrest 1 Remove the swingaway footrest assembly Refer to Installing Removing Using the Footrest Legrest on page 34 NOTE Lay the assembly on a flat surface to simplify this procedure 2 Remove impact guards and or calf strap if installed 3 Pull the cam lock lever up to the unlocked position 4 Push in the release buttons and reposition the lower footrest assembly to the desired height 5 Ensure that the release buttons fully protrude from holes on both sides of the upper footrest support 6 Rotate cam lock lever down to locked position 7 Replace impact guards and or calf Upper Footrest Support strap Release Button 8 Repeat this procedure for the other Adjustment footrest if necessary Holes ESSI 9 Reinstall the swingaway footrest assembly Refer to Cam Lock Lever Installing Removing Using the Footrest Legrest on page 34 Lower Footrest Assembly FIGURE 6 2
15. to restraints seat positioning straps it is the obligation of the DME dealer therapists and other healthcare professionals to determine if a seating positioning strap is required to ensure the safe operation of this equipment by the user Serious injury can occur in the event of a fall from a wheelchair A WARNING Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products The seat positioning strap is a positioning belt only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear belt MUST be replaced immediately Part No 1118386 9 P9000 XDT TYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERS P9000 XDT SEAT WIDTH 18 inches SEAT DEPTH 16 or 18 by extension BACK HEIGHT 17 18 or 19 inches SEAT TO FLOOR 19 inches OVERALL WIDTH EXCLUDING JOYSTICK Unfolded 24 inches Folded 13 inches OVERALL HEIGHT 38 inches with 17 inch back OVERALL LENGTH 28 inches base only to 47 inches with riggings and anti tippers WEIGHT W O BATTERIES AND FRONT RIGGINGS WITH UI BATTERIES SHIPPING 82 Ibs 142 Ibs 100 Ibs DRIVE WHEELS TIRES FLAT FREE 12 inches x 2 4 inches CA
16. user to reach bend and transfer in and out of the wheelchair These movements will cause a change to the normal balance cen ter of gravity and weight distribution of the wheelchair To determine and establish your particular safety limits practice bending reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair Reaching Leaning and Bending Forward NOTE For this procedure refer to FIGURE 3 2 1 Position the front casters as far forward as possible 2 Engage clutches and if applicable wheel locks A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees Wheel locks are an option You can order the wheelchair with or without wheel locks Transfer to and from the wheelchair in the presence of a qualified healthcare professional to determine individual safety limits Invacare strongly recommends ordering the wheel locks as an additional safeguard for the wheelchair user Part No 1118386 23 P9000 SECTION 3 SAFETY HANDLING OF WHEELCHAIRS FIGURE 3 2 Reaching Leaning and Bending Forward Reaching and Bending Backward A WARNING DO NOT lean over the top of the back upholstery This will change your center of gravity and may cause you to tip over NOTE For this procedure refer to FIGURE 3 3
17. with the six 6 mounting screws and washers starting with the top hole of the back cane 5 Install two 2 NEW tie wraps through the bottom holes of the upholstery to the bottom of the back upholstery to the back canes 6 Flip swing back arms down for use Refer to Swing Back Arms on page 39 Back Upholstery Washers Mounting Screws Back Cane 2 Tie Wraps Wash rs Mounting Screws FIGURE 8 2 Replacing the Back Upholstery Part 1118386 41 P9000 XDT SECTION 8 SEAT AND BACK Adjusting the Back Height NOTE For this procedure refer to FIGURE 8 3 NOTE Back canes must be adjusted to the same height 1 Remove the two 2 mounting screws and locknuts that secure the two 2 back canes to the wheelchair frame 2 Reposition the back canes to the desired height adjustment position 3 Reinstall the mounting screws and locknuts that secure the back canes to the wheelchair frame and securely tighten Back Cane La Wheelchair Frame Locknut Mounting Screw A o Jo my J N Back Height in inches e 9 NOTE Holes numbered from bottom to top for reference only There are no numbers on back canes or wheelchair frame FIGURE 8 3 Adjusting the Back Height P9000 XDT 42 Part No 1118386 SECTION 8 SEAT AND BACK Replacing Seat Positioning Strap NOTE For this procedure refer to FIGURE 8 4 1 If n
18. 000000000000000000 29 5 Joystick Switches and Indicators 29 Multi Function Charger n RR 29 Om Off Toggle a lca 29 Speed Control 29 OVS CN et 29 Information Gauge Display sciente nodis denen manendi 30 Operating the Wheelchair sedeant rinde pta tenda 32 Turning the Power On Off EREE ee DA ran Pub uer nik pb ed is 32 Using the 9 tod nananana a aa bue pie 32 Using the Joystick to Drive the Chair eerte retten ton ttes tentata ttn tonunts 32 SECTION 6 FRONT RIGGINGS 00000000000000000000000000000000000000000000000000000000 34 Installing Removing Using the Footrest Legrest ssssssssssssssssssssssssssssssssscsssssssscsssssssssssssessesseese 34 Installing Hmc 34 ots aac DER AU OO 35 M pp ge enel etae n Me Roe rcm 35 Adjusting the Footrest edere dud 35 Replacing the Heel LOOP A 36 Raising Lowering the Legrest Assembly eerte eere tatnen tonta tona ono 36 SECTION 7 ARMS 0000000000000000000000000000000000000000000000000000000000000000000000000 38 Adjusting Armrest 38 ATIS 39 Replacing Armrest 39 SECTION 8 SEAT AND BA
19. 3 Replacing Armrest Pad Part No 1118386 39 P9000 XDT SECTION 8 SEAT AND BACK SECTION 8 SEAT AND BACK A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that on off switch on the joystick is in the off position Replacing the Seat Upholstery NOTE For the following procedure refer to FIGURE 8 1 1 Remove the mounting screws that secure the existing seat upholstery to the wheelchair frame NOTE Refer to the following table to determine the number of mounting screws for each seat depth SEAT DEPTH NUMBER OF SCREWS 16 inch 18 inch 2 Remove the existing seat upholstery from the wheelchair frame 3 Install new seat upholstery by reversing Steps 1 2 Mounting Screws l 6 inch Seat Depth FIGURE 8 1 Replacing the Seat Upholstery P9000 XDT 40 Part No 1118386 SECTION 8 SEAT AND BACK Replacing the Back Upholstery NOTE For the following procedure refer to FIGURE 8 2 1 Flip swing back arms up and out of the way Refer to Swing Back Arms on page 39 2 Remove the six 6 mounting screws and washers that secure the EXISTING back upholstery to the back canes 3 Cut the tie wraps that secure the existing back upholstery to the wheelchair frame 4 Securely tighten the NEW back upholstery to the back canes
20. Adjusting the Footrest Height Part No 1118386 35 P9000 XDT SECTION 6 FRONT RIGGINGS Replacing the Heel Loop NOTE For this procedure refer to FIGURE 6 3 1 Pull the cam lock lever up to the unlocked position 2 Push in the release buttons and remove the lower footrest assembly 3 Remove the mounting screw spacer and locknut that secure the heel loop to the footrest 4 Remove existing heel loop from slide tube 5 Install new heel loop onto slide tube 6 Install the mounting screw spacer and locknut to secure the heel loop to the footrest Tighten until the spacer is secure Mounting Screw Cam Lock Lever Spacer Heel Loop Slide Tube Lower Footrest Assembly Footrest Locknut FIGURE 6 3 Replacing the Heel Loop 7 Insert the lower footrest assembly into the upper footrest assembly to desired height 8 Ensure that the release buttons fully protrude from holes on both sides of the upper footrest support 9 Rotate cam lock lever down to locked position Raising Lowering the Legrest Assembly A WARNING Ensure hands and fingers are clear of elevating legrest mechanism before pushing release lever to lower the elevating legrest Otherwise injury may occur due to pinch points The wheelchair user s leg MUST be supported by an assistant before attempting to lower legrest P9000 36 Part No 1118386 SECTION 6 FRONT RIGGINGS NOTE For this procedure refer to FIGURE 6 4 1 To rai
21. CK 000000000000000000000000000000000000000000000000000000000 40 Replacing the Seat Upholstery sicccci nisscsotiscsatseesdinsconssssadsotecdensidnssvonscubsshsansdsestonsndotiedtennddusdndeycnboueduosn 40 Replacing the Back Upholst ry 5 rient attain aint tnit e ient vesicae 41 Adjusting the Back 42 Replacing Seat Positioning Strap rt toda asain 43 SECTION 9 JOYSTICK 00000000000000000000000000000000000000000000000000000000000000000000 44 Preparing the Joystick for 44 Repositioning the Joystick rtt nnt ette ta tne 45 SECTION 10 CASTER 00000000000000000000000000000000000000000000000000000000000000000000 46 ejnt 46 P9000 XDT 4 Part No 1118386 SECTION BATTERIES 0000000000000000000000000000000000000000000000000000000000000000 47 When Charge Batteries x dadas iud 47 Charging Batteries NCC 48 Description and Use of Battery Chargers sssssssssssssssssssssssessssssssssesssssessesssssssssssscessssesses 48 Connecting the Battery Chargers 49 Replacing the Batteries is cest On ptem pde ED QURE MO UE RUE 49 Recommended Battery Types eee eene tente tente tentato tentata tanta ten sa ten toten tonto sone 49 Cleaning Battery Terminals 50 Removing Installing the Battery Boxes eerte tete tette ten to
22. OND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Corporation www invacare com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria Ohio USA Mississauga Ontario Invacare Corporation 44036 2125 147 4G4 Canada Yes you can P9000 and SPJ are 800 333 6900 800 668 5324 trademarks of Invacare Corporation 9 2004 Invacare Corporation Yes you can Part No 1118386 Rev B 10 04
23. Owner s Operator and Maintenance Manual P9000 XDT DEALER This manual MUST be given to the user of the wheelchair USER BEFORE using this wheelchair read this manual and save for future reference For more information regarding Invacare products parts and services please visit www invacare com Yes you can A WARNING A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS WHEELCHAIR ALSO A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES IN THE SERVICE MANUAL WHEELCHAIR USERS DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING 1 THE OWNER S OPERATOR AND MAINTENANCE MANUAL AND 2 THE SEATING SYSTEM S MANUAL IF APPLICABLE IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS AND INSTRUCTIONS CONTACT INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO SERVICE OR OPERATE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY RESULT DEALERS AND QUALIFIED TECHNICIANS DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING 1 THE OWNER S OPERATOR AND MAINTENANCE MANUAL 2 THE SERVICE MANUAL IF APPLICABLE AND 3 THE SEATING SYSTEM S MANUAL IF APPLICABLE IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS AND INSTRUCTIONS CONTACT INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO SERVICE OR OPERATE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY RESULT NOTE Updated versions of this manual are available on www in
24. PS 1 3 for other armrest Armrest Locked ra Vertical AP pa Height Adjustment Lever 4 Unlocked a Horizontal G x FIGURE 7 1 Adjusting Armrest Height P9000 XDT 38 Part No 1118386 SECTION 7 ARMS Swing Back Arms A WARNING Make sure the armrest release lever is in the locked position before using the wheel chair NOTE For this procedure refer to FIGURE 7 2 1 Unlock the swing back arms by rotating the armrest release lever towards the outside of the wheelchair N Pull the front of the swing back arm straight up out of the arm socket and towards the rear of the wheelchair gp To use the swing back arm push the swing back arm towards the front of the wheelchair and then downward into the arm socket NOTE Armrest release lever MUST be in the unlocked position when placing armrest into the arm sockets 4 Lock the swing back arms by rotating the armrest release lever towards the inside of the wheelchair Front Swing Back Arm Armrest Release Lever Rear x Arm Socket Tat a FIGURE 7 2 Swing Back Arms Replacing Armrest Pad NOTE For this procedure refer to FIGURE 7 3 1 Remove the mounting screws that A t Pad secure the armrest pad to the armrest Nus rmrest Pa assembly Armrest Assembly 2 Replace armrest pad and securely tighten with the existing mounting Screws Mounting Screws FIGURE 7
25. S 19 Stability and ioo ote 19 Coping With Everyday 19 Note to Wheelchair Assistants sssssssssssssssssssssssessessssssssssssssssssssssssssssssssesseessssssseessssssessssees 20 peanut dio e du n dated 20 atem aa 20 Liftirig StalU Ways osecsucitdiesesecitee teilen epica eidem tidekde sepu iu dendi 21 Transferring to and From Other Seats 22 Percentage of Weight Distribution eset 23 Reaching Leaning and Bending Forward 23 Reaching and Bending Backward 24 SECTION 4 SAFETY INSPECTION TROUBLESHOOTING 25 Safety Inspection Checklists acaso ao Erase et e tlt s bsc 25 Inspect Adjust Initially cotum doter deed npe Dehesa 25 Inspect Adjust Weekly rdi ertt aiia 26 OSE Month etd ps 26 Iispect Adiuse Perlodically 26 Troubleshooting Mechanical rte iai 27 Troubleshooting e b eb Meuse eb ci uos 27 Checking Battery Charge a telles 28 Part No 1118386 3 P9000 XDT SECTION 5 WHEELCHAIR OPERATION 0000000000000000000000000
26. SITIVE Terminal Post Note position of clamp FIGURE 11 6 Connecting Battery Cables Perform one 1 of the following methods for connecting the battery cable s e Dual U1 Batteries Use direct mount method described on page 54 Refer to FIGURE 11 7 e Dual Group 22NF Batteries with Mounting Holes in the Terminal s Post s Use direct mount method described on page 54 Refer to FIGURE 11 7 Dual Group 22NF Batteries without Mounting Holes in the Terminal s Post s Use battery clamp method described on page 57 Refer to FIGURE 11 8 and FIGURE 11 9 Direct Mount Method NOTE For this procedure refer to FIGURE 11 7 1 Install battery terminal cap s onto battery cable s A Dual U1 Batteries i ORANGE battery terminal cap onto RED battery cable ii GREY battery terminal cap onto BLACK battery cable B Dual Group 22NF BATTERIES i RED battery terminal cap onto RED battery cable ii BLACK battery terminal cap onto BLACK battery cable P9000 XDT 54 Part No 1118386 SECTION BATTERIES A CAUTION When connecting the battery cables to the battery ies the battery cable s MUST be connected to the battery terminal s post s as shown in Detail or Detail of FIGURE 11 7 depending on battery type Otherwise damage to the battery cable may result when installing battery terminal caps N Connect battery cable s to battery ies terminal s post s as shown in Detail A or Detail B
27. STERS W PRECISION SEALED BEARINGS 8x 1 inches semi pneumatic ANTI TIPPERS Removable FOOTRESTS LEGRESTS Swingaway Removable ARMRESTS Adjustable Height Desk UPHOLSTERY Black Nylon BATTERIES BATTERY SIZE NOT SUPPLIED TWO 2 REQUIRED UI SPEED M P H 0 to 4 TURNING RADIUS CHAIR ONLY CHAIR WITH FOOTREST CHAIR WITH ANTI TIPPERS Front 26 inches Rear 13 inches 36 inches 16 inches RANGE VARIABLE 12 14 miles with Ul batteries WEIGHT LIMITATION 250 Ibs NOTE Range will vary with battery conditions surface terrain and operating weight Includes seating system and accessories P9000 XDT 10 Part 1118386 LABEL LOCATIONS LABEL LOCATIONS O IMPORTANT NOTICE The wheel locks this wheelchair have been pre set at the factory to comply with the Veterans Administration functional Standard 8320 01 of the Federal Register paragraph 3 2 4 5 3 If these wheel locks do not meet your needs follow instructions below Any wheel lock adjustments should embed wheel lock shoe at least 1 8 into tire when locked 3 16 pneumstic tires INSTRUCTIONS FOR WHEEL LOCK ADJUSTMENTS Loosen wheel lock mounting fastener which runs through mounting bracket and frame Slide clamp toward rear wheel until wheel lock shoe is embedded into tire material at least 1 8 when handle is engaged to the lock position 3 16 for tir
28. art No 1118386 SECTION 3 SAFETY HANDLING OF WHEELCHAIRS A WARNING DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant Roll the wheelchair forward and SLOWLY lower the wheelchair in one continuous movement Push the wheelchair forward until the rear wheels roll up and over the curb A WARNING Make sure anti tipper wheels are pointing down towards the ground floor before using the wheelchair Turn the anti tipper wheels down towards the ground floor Lifting Stairways A WARNING DO NOT attempt to move an occupied power wheelchair between floors using a stairway Use an elevator to move an occupied power wheelchair between floors If moving a power wheelchair between floors by means of a stairway the occupant MUST be removed and transported independently of the power wheelchair Extreme caution is advised when it is necessary to move an unoccupied power wheelchair up or down the stairs Invacare recommends using two 2 assistants and making thorough preparations Use ONLY secure nondetachable parts for hand hold supports It is strongly recommended to lift the wheelchair only by the rear frame and the front forks otherwise injury or damage may occur DO NOT attempt to lift the wheelchair by any removable detachable parts Lifting by means of any removable detachable parts of a wheelchair may result in injury to the user or damage to the wheelc
29. aversing curbs or other impediments Also be aware of detachable parts such as arms or legrests These must NEVER be used to move the wheelchair or as lifting supports as they may be inadvertently released resulting in possible injury to the user and or assistant s When learning a new assistance technique have an experienced assistant help you before attempting it alone Tipping A WARNING DO NOT tip the wheelchair without assistance When tipping the wheelchair an assistant should grasp the back of the wheelchair on a non removable non detachable part Inform the wheelchair occupant before tipping the wheelchair and remind him her to lean back Be sure the occupant s feet and hands are clear of all wheels Tipping Curbs After mastering the techniques of tipping the wheelchair use this procedure to tackle curbs short stairs etc This procedure requires two 2 assistants The second assistant should be positioned at the front of the wheelchair lifting upward on a non removable non detachable part of the wheelchair frame when lifting the wheelchair and stabilizing the wheelchair when the wheelchair is being lowered to the ground The first assistant should turn the anti tippers so the wheels are pointing up apply a continuous downward motion until the balance point is achieved and the front casters clear the curb At this point the assistants will feel a difference in the weight distribution P9000 20 P
30. being used 2 Medium range mobile transceivers such as those used in police cars fire trucks ambulances and taxis These usually have the antenna mounted on the outside of the vehicle and 3 Long range transmitters and transceivers such as commercial broadcast transmitters radio and TV broadcast antenna towers and amateur HAM radios NOTE Other types of hand held devices such as cordless phones laptop computers AMIFM radios TV sets CD players cassette players and small appliances such as electric shavers and hair dryers so far as we know are not likely to cause EMI problems to your powered wheelchair Part No 1118386 17 P9000 XDT SECTION 2 EMI INFORMATION A WARNING Powered Wheelchair Electromagnetic Interference EMI Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna source the EM fields from hand held radio wave sources transceivers are of special concern It is possible to unintentionally bring high levels of EM energy very close to the powered wheelchair s control system while using these devices This can affect powered wheelchair movement and braking Therefore the warnings listed below are recommended to prevent possible interference with the control system of the powered wheelchair Electromagnetic interference EMI from sources such as radio and TV stations amateur radio HAM transmitters two way radios and cellular phones can affect powered wh
31. ck is in SPEED LIMIT mode The current state of bat tery charge will be dis played at the same time All LEDs are flashing slowly Joystick has detected Out of Neu tral at Power Up mode Release the joystick back to Neutral Part No 1118386 All LEDs are flashing quickly 3l Joystick has detected a fault Joystick uses Flash codes to indicate faults Refer to the electronics manual P NI I 10532 P9000 XDT SECTION 5 WHEELCHAIR OPERATION Operating the Wheelchair NOTE For this procedure refer to FIGURE 5 2 Turning the Power On Off 1 To turn the power ON press the on off button NOTE After turning power on all indicators will light briefly and the display gauge will indicate one of the following A The Current Battery Charge Shows all LEDs lit or partial LEDs lit Refer to the preceding information gauge display table B Out Of Neutral At Power up Shows all LEDs flashing slowly This occurs when the power is turned on when the joystick is out of neutral This feature prevents sudden and unexpected movements of the power chair 2 To turn the power off press the on off button Using the Horn 1 Press the horn button located above the information gauge on the joystick housing Using the Joystick to Drive the Chair The joystick is located at the front of the joystick housing and provides smooth control of speed and direction It is equipped with 360 degrees of mob
32. d is for Group 22NF batteries ONLY Refer to the battery manufacturer for the proper lifting strap and or battery tools for U1 battery removal installation A WARNING ALWAYS use a battery lifting strap when lifting a battery It is the most convenient method and assures that the battery acid will not spill It also helps to prolong the life of the battery The battery lifting strap supplied is for Group 22NF batteries ONLY Refer to the battery manufacturer for the proper lifting strap and or battery tools for UI battery removal installation DO NOT tip the batteries Keep the batteries in an upright position NOTE If there is battery acid in the bottom or on the sides of the battery box es or battery ies apply baking soda to these areas to neutralize the battery acid Before reinstalling the new or existing battery ies clean the baking soda from the battery box es or battery ies NOTE When securing battery lifting strap to battery observe polarity markings located on the ends of the battery lifting strap side to POSITIVE battery terminal post and side to NEGATIVE battery terminal post P9000 XDT 52 Part No 1118386 SECTION BATTERIES 1 If necessary remove the battery boxes from the wheelchair Refer to Removing Installing the Battery Boxes on page 50 2 Secure the battery lifting strap to battery terminal s post s A CAUTION Some battery manufacturers mold a carrying strap and or hold dow
33. e Screw POSITIVE Red Cable 1 4 20 Hex Flange Locknuts POSITIVE NEGATIVE Terminal Post Terminal Post RED Terminal NEGATIVE Cap Black Cable NEGATIVE Terminal Post CONNECT BLACK Tie Wraps CABLE TO Terminal TERMINAL AS Cap SHOWN Detail Installing Battery Terminal Cap onto Battery Cable Cable Terminal Cap NOTE For clarity only one 1 cable and terminal cap are shown Both caps install in the same manner FIGURE 11 7 Connecting Battery Cables Direct Mount Method P9000 XDT 56 Part No 1118386 SECTION BATTERIES 8 Install the battery box es into the wheelchair Refer to Removing Installing the Battery Boxes on page 50 NOTE New battery ies MUST be fully charged before using otherwise the life of the battery ies will be reduced 9 If necessary charge the battery ies Refer to Charging Batteries on page 48 Battery Clamp Method A CAUTION The battery clamp of the POSITIVE battery terminal post MUST be mounted in the position shown in FIGURE 11 8 Otherwise the battery box top cannot be installed properly NOTE For this procedure refer to FIGURE 11 8 and FIGURE 11 9 Hex Nut EGATIVE Terminal Post and Clamp POSITIVE Terminal Post Note position of clamp FIGURE 11 8 Connecting Battery Cables Battery Clamp Method 1 Perform one 1 of the following e Ifthe battery clamp of the POSITIVE batter
34. e the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECT TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE COMMERCIAL OR INSTITUTIONAL USE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE INSTRUCTIONS A CHANGE IN OPERATING NOISE PARTICULARLY RELATIVE TO MOTORS AND GEARBOXES DOES NOT CONSTITUTE A FAILURE ALL SUCH DEVICES WILL EXHIBIT A CHANGE IN OPERATING NOISE DUE TO AGING THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEY
35. e wheel locks when the wheelchair power is on and the clutches are engaged otherwise damage to the wheelchair may result NOTE Use the wheel locks whenever the clutches are disengaged and the wheelchair is being pushed Part No 1118386 63 P9000 SECTION 14 ANTI TIPPERS SECTION 14 ANTI TIPPERS A WARNING After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result Installing Removing Adjusting Anti Tippers NOTE For this procedure refer to FIGURE 14 1 Installing WARNING Anti tippers MUST be fully engaged and spring buttons fully protruding out of adjustment holes BEFORE using the wheelchair Ensure both anti tippers have the same ground clearance A 1 to 2 inch clearance between the bottom of the anti tipper wheels and the ground floor MUST be maintained at all times Anti tippers MUST be used at all times When outdoors on wet soft ground or gravel surfaces anti tippers may not provide the same level of protection against tipover Extra caution must be observed when traversing such surfaces Press the two 2 release buttons in and insert the anti tippers with anti tipper wheels pointing toward the ground floor into the support tubes until the release buttons lock in place N Measure the distance between the bottom of the anti tipper wheels and the ground floor and ensure it is 175 2 i
36. ecessary remove the seat cushion from the seat upholstery 2 Remove the two 2 rear phillips screws and washers that secure the seat upholstery and seat positioning strap to the crossbraces 3 Remove the two 2 halves of the seat positioning strap from the crossbraces 4 Position the two 2 new seat positioning strap halves between the seat upholstery and the crossbraces 5 Reinstall the rear phillips screws and washers that secure the seat upholstery and seat positioning strap to the crossbraces NOTE Washer is positioned on top of seat upholstery 6 If necessary reinstall the seat cushion onto the seat upholstery Washer Rear Phillips Screw N Seat Positioning Strap ye Seat Upholstery Crossbrace FIGURE 8 4 Replacing Seat Positioning Strap Part No 1118386 43 P9000 XDT SECTION 9 JOYSTICK SECTION 9 JOYSTICK A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that On Off switch on the joystick is in the OFF position Preparing the Joystick for Use NOTE For this procedure refer to FIGURE 9 1 NOTE The joystick is factory installed on the right side of the wheelchair To reposition the joystick onto the left side of the wheelchair refer to Repositioning the Joystick on page 45 The joystick sh
37. eelchairs and motorized scooters FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED WHEELCHAIR MOVEMENT WHICH COULD RESULT IN SERIOUS INJURY 1 Do not operate hand held transceivers transmitters receivers such as citizens band CB radios or turn ON personal communication devices such as cellular phones while the powered wheelchair is turned ON 2 Be aware of nearby transmitters such as radio or TV stations and try to avoid coming close to them 3 If unintended movement or brake release occurs turn the powered wheelchair OFF as soon as it is safe 4 Be aware that adding accessories or components or modifying the powered wheelchair may make it more susceptible to EMI NOTE There is no easy way to evaluate their effect on the overall immunity of the powered wheelchair 5 Report all incidents of unintended movement or brake release to the powered wheelchair manufacturer and note whether there is a source of EMI nearby Important Information 1 20 volts per meter V m is a generally achievable and useful immunity level against EMI as of 1994 the higher the level the greater the protection 2 The immunity level of the product is unknown Modification of any kind to the electronics of this wheelchair as manufactured by Invacare may adversely affect the RFI immunity levels P9000 XDT 18 Part No 1118386 SECTION 3 SAFETY HANDLING OF WHEELCHAIRS
38. es Tighten momting fastener to secure mounting bracket in desired location and recheck lock shoe embedding Inspect for correct locking action actual use BEI 00078X021 0394 Part No 1118386 FORE Lower Frame Tube WEIGHT CAPACITY 250 LBS 114 kgs REFER TO OWNER S MANUAL P N 1111013 A WARNING to Owner s Manual for proper anti tipper setting 1085379 A WARNING DO NOT OPERATE WITHOUT THE ANTI TIP TUBES REV 5 98 INSTALLED P9000 XDT SECTION GENERAL GUIDELINES SECTION GENERAL GUIDELINES A WARNING This section contains important information for the safe operation and use of this product DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as Owner s Manuals Service Manuals or Instruction Sheets supplied with this product or optional equipment If you are unable to under stand the Warnings Cautions or Instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur Controller Settings Repair or Service A CAUTION Set up of the Electronic Control Unit is to be performed only by a qualified techni cian The fine tuning adjustments of the controller may affect other activities of the wheelchair
39. gainst tipover Extra caution must be observed when traversing such surfaces Wheel locks are not brakes DO NOT attempt to stop a moving wheelchair with the wheel locks DO NOT engage or disengage the clutches until the power is in the OFF position DO NOT operate on roads streets or highways DO NOT climb go up or down ramps or traverse slopes greater than 9 DO NOT attempt to move up or down an incline with a water ice or oil film DO NOT attempt to drive over curbs or obstacles Doing so may cause your wheelchair to turn over and cause bodily harm or damage to the chair DO NOT leave the power button in the on position when entering or exiting your wheelchair DO NOT stand on the frame of the wheelchair DO NOT use the footplates as a platform When getting in or out of the wheelchair make sure that the footplates are in the upward position or swing the footrests toward the outside of the chair DO NOT stand on the front riggings otherwise damage may occur When getting in or out of the wheelchair make sure that the footplates on the front riggings are in the upward position or moved out of the way ALWAYS wear your seat positioning strap Part No 1118386 13 P9000 XDT SECTION I GENERAL GUIDELINES The seat positioning strap is a positioning belt only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear belt must be replaced
40. hair The weight of the wheelchair without the user and batteries is between 80 and 127 Ibs Follow this procedure for moving the wheelchair between floors when an elevator is NOT available or lifting the wheelchair is necessary NOTE When using a stairway to move the wheelchair seat and any accessories move all wheelchair components away from the stairway prior to reassembly Remove the occupant from the wheelchair Remove the battery boxes from the wheelchair Refer to Removing Installing the Battery Boxes on page 50 3 If necessary fold the wheelchair Refer to Transporting the P9000 XDT on page 66 9 B Bend your knees and keep your back straight Part No 1118386 21 P9000 XDT SECTION 3 SAFETY HANDLING OF WHEELCHAIRS 5 Using non removable non detachable parts of the wheelchair lift the wheelchair off the ground and transfer the wheelchair up or down the stairs 6 The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been carried away from the stairway ESCALATORS WARNING DO NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur Transferring to and From Other Seats A WARNING ALWAYS turn the wheelchair power OFF and engage the clutches to prevent the wheels from moving BEFORE attempting to transfer in or out of the wheelchair Also make sure every precaution is taken to reduce the gap distance by turn
41. harger checked Replace batteries if necessary Contact dealer Invacare for service Motor chatters or runs Electrical malfunction irregularly Contact dealer Invacare Wheelchair does not One 1 both clutches respond to commands disengaged Power on battery indicator flashes Engage motor locks clutches Only one 1 drive wheel Electrical malfunction turns One 1 clutch is disengaged Part No 1118386 27 Contact dealer Invacare for service Engage clutch P9000 XDT SECTION 4 SAFETY INSPECTION TROUBLESHOOTING SYMPTOM PROBABLE CAUSE SOLUTIONS Joystick erratic or does not respond as desired Electrical malfunction Controller programmed improperly Contact dealer Invacare for service Reprogram controller Contact dealer Invacare for service Wheelchair does not Poor battery terminal con Clean terminals respond to commands nection Power indicator off even after recharging Electrical malfunction Contact dealer Invacare NOTE For additional troubleshooting information and explanation of error codes refer to the Electronics Manual P N 1110532 supplied with each wheelchair Checking Battery Charge Level Don t perform any installation or maintenance with out first reading this manual Don t make it a habit to discharge batteries to the lowest level Don t use randomly chosen batteries chargers Don t put new batteries i
42. he charger should automatically shut off when full charge is obtained Some basic concepts which will help you understand this automatic process are The amount of electrical current drawn within a given time to charge a battery is called charge rate If due to usage the charge stored in the battery is low the charge rate is high as indicated by the green light on the charger Initially the green light will stay illuminated for a short period of time followed by a longer period of off time As a charge builds up the charge rate is reduced and the green light will stay illuminated for a longer period of time followed by a shorter off time NOTE If performing the charging procedures independently READ and CAREFULLY follow the individual instructions for each charger supplied or purchased NOTE If charging instructions are not supplied consult a qualified service technician for proper procedures Required items TOOLS QUANTITY COMMENTS Battery charger Supplied Extension cord Not Supplied NOTE 3 prong plug 15 ampere current rating industrial type P9000 XDT 48 Part No 1118386 SECTION BATTERIES Connecting the Battery Charger NOTE For this procedure refer to FIGURE 11 2 1 Attach the battery charger connector to the charger port on the joystick Charger Port 2 Plug the charger s AC power cord or extension into the grounded 120 VAC wall outlet 3 Wait until charging is complete NOTE If
43. ility for ease of operation The joystick is spring loaded and automatically returns to the upright neutral position when released Pushing the joystick in a given direction causes the chair to move in that direction The joystick has proportional drive control meaning that the further it is pushed from the upright neutral position the faster the wheelchair moves The maximum speed however is limited by the setting of the speed control knob To slow the wheelchair to a stop simply release the joystick The wheelchair has automatic speed and direction compensation to minimize corrections When first learning to drive select a slow speed and try to drive the wheelchair as slowly as possible by pushing the joystick slightly forward This exercise will help you learn to utilize the full potential of the proportional control and allow you to start and stop smoothly To drive the wheelchair perform the following 1 Adjust speed control switch to the appropriate setting 2 Turn the power on Refer to Turning the Power On Off on page 32 P9000 XDT 32 Part No 1118386 SECTION 5 WHEELCHAIR OPERATION 3 Move the joystick in the following manner FORWARD Push forward on the joystick REVERSE Pull back on the joystick Turn RIGHT Move the joystick RIGHT Turn LEFT Move the joystick LEFT STOP Release the joystick and the wheelchair will quickly slow down NOTE The joystick MUST be in the NEUTRAL position f
44. ing both casters parallel to the object you are transferring onto A CAUTION When transferring position yourself as far back as possible in the seat This will pre vent broken screws damaged upholstery and the possibility of the wheelchair tip ping forward NOTE This activity may be performed independently provided you have adequate Minimum Gap Distance mobility and upper body strength NOTE For this procedure refer to FIGURE 3 1 1 Position the wheelchair as close as possible along side the seat to which you are transferring with the casters pointing parallel to it 2 After the wheelchair is positioned properly for transfer verify that the clutches are engaged Refer to FIGURE 3 1 Transferring to and From Engaging Disengaging the Clutches on Other Seats page 61 3 Shift body weight into seat with transfer During independent transfer little or no seat platform will be beneath you Use a transfer board if at all possible P9000 XDT 22 Part No 1118386 SECTION 3 SAFETY HANDLING OF WHEELCHAIRS Percentage of Weight Distribution A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees Proper positioning is essential for your safety When reaching leaning bending or bending forward it is important to use the casters as a tool to maintain stability and balance Many activities require the wheelchair
45. ing information refer to FIGURE 5 1 Multi Function Charger Port The multi function charger port is located at the front of the joystick housing This provides easy access for charging the wheelchair batteries This port also serves as the Remote Programmer Communication connection On Off Toggle Switch This toggle switch is located at the back of the joystick housing Speed Control switch The speed control switch is located on the back of the joystick housing This rotary switch is used for controlling the speed and acceleration of the wheelchair 1 Turn the switch clockwise to increase the speed of the wheelchair 2 Turn the switch counterclockwise to decrease the speed of the wheelchair Joystick The joystick has proportional drive control meaning that further the joystick is pushed from the upright neutral position the faster the wheelchair moves Your top speed however is limited by the setting of the speed control knob and programmed settings To slow the wheelchair to a stop simply release the joystick The wheelchair has automatic speed and direction compensation to minimize corrections Part No 1118386 29 P9000 XDT SECTION 5 WHEELCHAIR OPERATION Joystick Hom Information Gauge On Off Knob To Controller Multi Function Charger Port FIGURE 5 1 SPJ Joystick Switches and Indicators Information Gauge Display The Information Gauge Display is located on the front of the joystick housi
46. io HAM transmitters two way radios and cellular phones The interference from radio wave sources can cause the powered wheelchair to release its brakes move by itself or move in unintended directions It can also permanently damage the powered wheelchair s control system The intensity of the interfering EM energy can be measured in volts per meter V m Each powered wheelchair can resist EMI up to a certain intensity This is called its immunity level The higher the immunity level the greater the protection At this time current technology is capable of achieving at least a 20 V m immunity level which would provide useful protection from the more common sources of radiated EMI There are a number of sources of relatively intense electromagnetic fields in the everyday environment Some of these sources are obvious and easy to avoid Others are not apparent and exposure is unavoidable However we believe that by following the warnings listed below your risk to EMI will be minimized The sources of radiated EMI can be broadly classified into three types 1 Hand held Portable transceivers transmitters receivers with the antenna mounted directly on the transmitting unit Examples include citizens band CB radios walkie talkie security fire and police transceivers cellular telephones and other personal communication devices NOTE Some cellular telephones and similar devices transmit signals while they are ON even when not
47. k securely Ensure armrest pads sit flush against arm tubes Ensure seat is secured to wheelchair frame Clean seat upholstery and armrests Q Ensure wheel mounting nuts are secure on drive wheels Ensure no excessive side movement or binding occurs when drive wheels are lifted and spun when disengaged free wheeling Ensure that drive wheel axle bolts and locking tab washers are secure Ensure that the wheel locks engage properly and do not interfere with the tires when rolling Also ensure that the pivot points are free of wear and looseness Inspect caster assembly has proper tension when caster is spun Caster should come to a gradual stop Loosen tighten caster locknut if wheel wobbles noticeably or binds to a stop Ensure all caster wheel fork headtube fasteners are secure Inspect tires for flat spots and wear If tires are pneumatic check for proper inflation Part No 1118386 25 P9000 SECTION 4 SAFETY INSPECTION TROUBLESHOOTING Seat and or back upholstery have rips and do not sag Replace if necessary Inspect Adjust Weekly Seat is secured to wheelchair frame Seat release latch is not worn and is functional Replace if necessary Inspect tires for flat spots and wear If the tires are pneumatic check for proper inflation Ensure all caster wheel fork headtube fasteners are secure Ensure arm pivot points are not worn and or loose Rep
48. lace if necessary Inspect Adjust Monthly Ensure wheel mounting nuts are secure on drive wheels Ensure no excessive side movement or binding occurs when drive wheels are lifted and spun when disengaged free wheeling Ensure that drive wheel axle bolts and locking tab washers are secure Inspect caster assembly has proper tension when caster is spun Caster should come to a gradual stop Loosen tighten caster locknut if wheel wobbles noticeably or binds to a stop Ensure that the wheel locks engage properly and do not interfere with the tires when rolling Also ensure that the pivot points are free of wear and looseness Inspect the seat positioning strap for signs of wear Replace if worn or damaged Ensure that the buckle on the seat positioning strap latches Replace if necessary Verify that the hardware that attaches the seat positioning strap to the seat frame is secure and undamaged Replace if necessary Inspect Adjust Periodically Q Ensure wheelchair rolls straight no excessive drag or pull to one side Ensure that all fasteners on the clothing guards are secure Ensure arms are secure but easy to release and adjustment levers engage properly Ensure adjustable height arms operate and lock securely Ensure arm pivot points are not worn and or loose Replace if necessary Ensure armrest pads sit flush against arm tubes Ensure seat and or back upholstery have no rips and do not
49. low the manufacturer s instructions for each charger supplied or purchased If charging instructions are not supplied consult a qualified technician for proper procedures After charging batteries ALWAYS make sure that the battery charger cord is unplugged Failure to do this could result in damage to the cord or personal injury to the user or bystanders When using an extension cord use only a three 3 wire extension cord having at least 16 AWG American Wire Gauge wire and the same or higher electrical rating as the device being connected Use of improper extension cord could result in risk of fire and electric shock Ensure the pins of the extension cord plug are the same number size and shape as those on the charger DO NOT under any circumstances cut or remove the round grounding plug from the charger AC cable plug or the extension cord plug Three 3 prong to two 2 prong adapters should not be used Use of three 3 prong adapters can result in improper grounding and present a shock hazard to the user Grounding Instructions DO NOT under any circumstances cut or remove the round grounding prong from any plug used with or for Invacare products Some devices are equipped with three prong grounding plugs for protection against possible shock hazards and fire Where a two prong wall receptacle is encountered it is the personal responsibility and obligation of the customer to contact a qualified electrician and have the t
50. n flanges directly into the battery case Batteries which interfere with the battery box cannot be used for these applications Attempting to wedge a battery into a battery box may damage the box and or the battery 3 Place batteries into battery box bottom UI Battery Battery Lifting Strap Box Bottom Molded Carrying Strap or DN Hold Down Flanges 22NF Battery Box Bottom Battery Group 22NF ONLY Terminal s Post s FIGURE 11 5 Installing Removing Batteries Into From Battery Boxes Connecting Battery Cables A WARNING The use of rubber gloves and chemical goggles or face shields is recommended when working with batteries NEVER allow any of your tools and or battery cable s to contact BOTH battery terminal s post s at the same time An electrical short may occur and serious personal injury or damage may occur The correct battery terminal configurations shown in FIGURE 11 6 MUST be used Batteries that have the reversed terminal configuration MUST NOT be used Oth erwise serious injury or damage may occur Part No 1118386 53 P9000 SECTION BATTERIES DO NOT USE POSITIVE NEGATIVE Terminal Post Terminal Post POSITIVE Terminal Post NEGATIVE Terminal Post Ul Batteries POSITIVE Terminal Post 0 NOT USE Terminal Post and Clamp Note position of clamp NEGATIVE Terminal Post and Clamp E08 PO
51. nches If necessary adjust height To adjust the height of the anti tippers refer to Adjusting Height on page 64 Removing 1 Press release buttons in and remove the anti tippers from the support tubes Adjusting Height 1 Press the release buttons in and adjust the anti tippers to the desired height NOTE The distance between the bottom of the anti tipper wheels and the ground floor MUST be 1 to 2 inches NOTE Both anti tippers should be adjusted to the same height P9000 XDT 64 Part No 1118386 SECTION 4 ANTI TIPPERS Release Button to 2 inch Anti tipper Adjustment Holes Clearance FIGURE 14 1 Installing Removing Adjusting Anti Tippers Part No 1118386 65 P9000 XDT TRANSPORTING TRANSPORTING A WARNING After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result Transporting the P9000 XDT A WARNING The weight of the wheelchair without the user and batteries is approximately 82 Ibs Use proper lifting techniques lift with your legs to avoid injury Extreme caution is advised when it is necessary to move an unoccupied power wheelchair Invacare recommends using two 2 assistants and making thorough preparations Make sure to use ONLY secure non detachable parts for hand hold supports NOTE For this procedure refer to FIGURE 15 1 Unfolding Folding the Wheelchair WARNING Keep ha
52. nds and fingers clear of moving parts to avoid injury DO NOT place hand or fingers on the underside of the seat rail when opening or closing the wheelchair DO NOT sit or transfer into the wheelchair unless it is fully open and the seat rails are fully seated into the side frame H blocks Unfolding 1 Push down on the seat rails until the seat rails are positioned in the seat guides 2 Assemble the wheelchair by following the instructions in this manual Folding Remove the anti tippers Refer to Installing Removing Adjusting Anti Tippers on page 64 Remove the batteries Refer to Removing Installing the Battery Boxes on page 50 Remove the footrests legrests from the wheelchair Refer to Installing Removing Using the Footrest Legrest on page 34 Remove the battery tray from the wheelchair Refer to Installing Removing Battery Tray on page 51 EN um os gt Lift up on seat rails of wheelchair P9000 XDT 66 Part No 1118386 TRANSPORTING Refer to Removing Installing the Battery Boxes on page 50 and Installing Removing Battery Tray on page 51 Refer to Installing Removing Adjusting Anti Tippers on page 64 Refer to Installing Removing Using the Footrest Legrest on page 34 FIGURE 15 1 Transporting the P9000 Part No 1118386 67 P9000 XDT LIMITED WARRANTY PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED
53. ng It provides the following information to the user on the status of the wheelchair 1 Power is on 2 True state of battery charge including notification of when the battery requires charging A GREEN LED is lit indicating well charged batteries B Only AMBER LEDs are lit indicating batteries are moderately charged Recharge batteries before taking a long trip C Only RED LED is lit indicating batteries are running out of charge Recharge batteries as soon as possible 3 Program inhibit or charge modes 4 Fault indication Flash Codes The Information Gauge display also serves as a system diagnostic device when a fault is detected by the control module A specific number of flashes of the LEDs indicate the type of fault detected Refer to the following table of the diagnostic indications of the wheelchair status P9000 XDT 30 Part No 1118386 DISPLAY DESCRIPTION All LEDs are OFF SECTION 5 WHEELCHAIR OPERATION DEFINITION Power is OFF COMMENTS All LEDs are ON Power is ON Fewer than three 3 LEDs on implies reduced battery charge Left RED LED is flashing Battery charge is low The batteries should be charged as soon as possi ble Left to Right chase alter nating with steady display Joystick is in program ming inhibit and or charg ing mode The steady LEDs indicate the current state of the battery charge Right GREEN LED is flash ing Joysti
54. nto From Battery Boxes on page 52 3 Clean the new battery terminals 4 Install the new batteries into the battery boxes Refer to Installing Removing Batteries Into From Battery Boxes on page 52 Install the battery boxes and tray onto the wheelchair Refer to Removing Installing the Battery Boxes on page 50 and Installing Removing Battery Tray on page 51 o Cleaning Battery Terminals A WARNING DO NOT allow the liquid in the battery to come in contact with skin clothes or other possessions It is a form of acid and harmful or damaging burns may result Should the liquid touch your skin wash the area immediately and thoroughly with cool water In serious cases or if eye contact is made seek medical attention IMMEDIATELY NEVER smoke or strike a match near batteries If the caps of the battery cells are removed NEVER look directly into them while charging batteries Examine battery clamps and terminals for corrosion N Verify that the plastic caps are in place over the battery cell holes Clean terminals and inside battery clamps by using a battery cleaning tool wire brush or medium grade sand paper NOTE When done these areas should be shiny not dull 4 Carefully dust off all metal particles Removing Installing the Battery Boxes A WARNING NEVER unplug the battery cables by pulling on the wires Unplug the battery cables by pulling on the connector ONLY Otherwise injury or damage
55. nto service before charging Don t tip or tilt batteries Don t tap on clamps or terminals with tools Don t mismatch your battery and chargers Don t use randomly chosen batteries or chargers P9000 XDT Read and understand this manual and any service infor mation that accompanies a battery and charger before operating the wheelchair Recharge as frequently as possible to maintain a high charge level and extend battery life Follow recommendations in this manual when selecting a battery or charger Fully charge a new battery before using Use a carrying strap to remove move or install a battery Push battery clamps onto terminals Spread clamps wider if necessary Use ONLY a GEL charger for a GEL or sealed battery and a regular charger for regular batteries 28 Part No 1118386 SECTION 5 WHEELCHAIR OPERATION SECTION 5 WHEELCHAIR OPERATION A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Set up programming of the Electronic Control Unit is to be performed ONLY by a qualified technician The fine tuning adjustments of the controller may affect other activities of the wheelchair Damage to the equipment could occur under these cir cumstances IF UNQUALIFIED INDIVIDUALS PERFORM ANY WORK ON THESE UNITS THE WARRANTY IS VOID SPJ Joystick Switches and Indicators NOTE For the follow
56. on motors A WARNING If clutch handles are forced to engage in the wrong direction as shown in FIGURE 12 1 the motors will be damaged and will need to be replaced N Perform one 1 of the following To Engage turn the clutch handles until they are pointing towards the rear of the wheelchair NEVER try to turn the clutch handles towards the front of the wheelchair To Disengage turn the clutch handles until they are pointing towards the rear wheels NEVER try to turn the clutch handles towards the inside of the wheelchair Top View Of Wheelchair Disengaged Toward rear wheels NOTE NEVER force clutch handles in these directions ill oooooot Jim 0 19 232 C3 EJ C3 E3 C3 Engaged Toward 7 rear of wheelchair Clutch Handle FIGURE 12 1 Engaging Disengaging the Clutches Part No 1118386 61 P9000 XDT SECTION 13 WHEEL LOCKS SECTION 13 WHEEL LOCKS A WARNING After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result Installing Adjusting Using the Wheel Locks NOTE For this procedure refer to FIGURE 13 1 Installing Adjusting NOTE Before adjusting or replacing the wheel lock assemblies ensure that the tires are inflated to the recommended psi on the side wall of tire NOTE If necessary remove th
57. or an accurate reading of battery charge To Move Left Joystick To Move Forward FIGURE 5 2 Using the Joystick to Drive the Chair Part No 1118386 33 P9000 XDT SECTION 6 FRONT RIGGINGS SECTION 6 FRONT RIGGINGS A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that ON OFF switch on the joystick is in the OFF position Installing Removing Using the Footrest Legrest NOTE For this procedure refer to FIGURE 6 1 NOTE This procedure applies to the swingaway footrest and elevating legrest Installing 1 Turn the swingaway footrest assembly to the side open footplate is perpendicular to wheelchair 2 Install the hinge plates on the swingaway footrest assembly onto the hinge pins on the wheelchair frame 3 Push the swingaway footrest assembly towards the inside of the wheelchair until it locks into place NOTE The footplate will be on the inside of the wheelchair when locked in place 4 Repeat this procedure for the other footrest assembly Footrest Release Lever Swingaway Footrest Assembly FIGURE 6 1 Installing Removing Using the Footrest Legrest P9000 XDT 34 Part No 1118386 SECTION 6 FRONT RIGGINGS Removing 1 Push the footrest release lever inward 2 Rotate swingaway footrest assembly outward 3 Lift
58. ould be repositioned by a qualified technician 1 Turn the adjustment lock lever to release the joystick mounting tube from the mounting bracket M Slide joystick mounting tube to the desired position Turn adjustment lock lever to secure joystick mounting tube in mounting bracket FIGURE 9 1 Preparing the Joystick for Use P9000 XDT 44 Part No 1118386 SECTION 9 JOYSTICK Repositioning the Joystick NOTE For this procedure refer to FIGURE 9 2 NOTE Before starting this procedure it may be necessary to snip the tie wraps not shown in FIGURE 9 2 securing the joystick control cord to the wheelchair Before snipping the tie wraps note the way the cord is secured to the chair so that it can be re secured in the same way at the end of the procedure 1 Turn the adjustment lock lever to release the joystick mounting tube from the mounting bracket 2 Remove the joystick from the wheelchair 3 Remove the three 3 hex screws that secure both halves of the mounting bracket to the arm tube 4 Reposition mounting bracket on opposite arm tube ensuring the threaded plate of the mounting bracket is on the inside of the arm tube 5 Using the three 3 hex mounting screws and washers secure both halves of the mounting bracket to the arm tube 6 Slide the joystick mounting tube through the mounting bracket to the desired position 7 Turn the adjustment lock lever to secure the joystick mounting
59. p 22NF Battery Detail A Top View Detail Tie Wraps Fuse box placement when POSITIVE box top is installed RED Cable POSITIVE NEGATIVE Terminal Post AME V Terminal Post Terminal Post and cues Tie Wraps RED Clamp Terminal Post and Cover Clamp NEGATIVE BLACK Cable Group 22NF Group 22NF Battery B attery Fuse Box BLACK Clamp Cover Detail Installing Battery Clamp Cover Cable NOTE For clarity only one 1 cable and clamp cover are shown Both clamp covers install in the same manner FIGURE 11 9 Connecting Battery Cables Battery Clamp Method Part No 1118386 59 P9000 SECTION BATTERIES Replacing Battery Box Retaining Strap A WARNING The battery box retaining strap MUST be fastened securely and adjusted properly to hold battery boxes in place before using the wheelchair NOTE For this procedure refer to FIGURE 11 10 1 Remove the battery boxes from the wheelchair Refer to Removing Installing the Battery Boxes on page 50 Remove the battery tray from the wheelchair Refer to Installing Removing Battery Tray on page 51 N A WARNING The retaining strap MUST be fed through the adjustable end of the battery box retaining strap buckle as shown in FIGURE 11 9 NOTE Take note of the position and orientation of the battery box retaining strap as it passes through the slots of the battery
60. plier for instruction in the use of oxygen Batteries The warranty and performance specifications contained in this manual are based on the use of deep cycle gel cell or sealed lead acid batteries Invacare strongly recommends their use as the power source for this unit If wet cell batteries are used follow all manufacturer guidelines and instructions for installation and maintenance Regardless of battery type proper battery footprint and use of battery terminal caps as defined in Batteries on page 47 must be followed Carefully read battery battery charger information prior to installing servicing or operating your wheelchair P9000 XDT 14 Part No 1118386 SECTION GENERAL GUIDELINES Charging Batteries NEVER attempt to recharge the batteries by attaching cables directly to the battery terminals DO NOT attempt to recharge the batteries and operate the wheelchair at the same time DO NOT operate wheelchair with extension cord attached to the AC cable DO NOT attempt to recharge the batteries when the wheelchair has been exposed to ANY type of moisture DO NOT attempt to recharge the batteries when the wheelchair is outside DO NOT sit in the wheelchair while charging the batteries DO NOT attempt to recharge batteries using at the same time BOTH the on board battery charger AND an independent battery charger plugged into the joystick charger port Doing so will reduce the life of the batteries READ and carefully fol
61. readed plastic insert from the wheel lock mounting hole in the wheelchair frame 1 Position the wheel lock on the wheelchair frame 2 Loosely install the hex screw and locknut that secures the wheel lock to the wheelchair frame 3 Make sure wheel lock is disengaged from rear wheel 4 Measure the distance between the wheel lock shoe and the rear wheel 5 Slide the wheel lock along the wheelchair until the measurement is between 5 32 and 5 16 inches Tighten the wheel lock to the wheelchair frame Repeat STEPS 2 6 for the opposite wheel lock Disengage the clutches Refer to Engaging Disengaging the Clutches on page 61 Engage the wheel locks and push against the wheelchair to determine if the wheel locks engage the rear wheels enough to hold the wheelchair Ec NDS 10 Repeat STEPS 3 9 until the wheel locks engage the rear wheels enough to hold the wheelchair 11 Engage clutches Refer to Engaging Disengaging the Clutches on page 61 P9000 XDT 62 Part No 1118386 SECTION 13 LOCKS Wheel Lock Handle Wheel Lock Shoe Distance between 5 32 to 5 16 inch FIGURE 13 1 Installing Adjusting Using the Wheel Locks Using The wheelchair is equipped with a pair of independently operated wheel locks located just in front of the rear wheels 1 To engage the wheel locks grip the handle and push forward to the lock position 2 To release reverse STEP 1 A CAUTION DO NOT use th
62. se the elevating legrest the assistant should hold the support tube and raise elevating legrests until the desired height is obtained 2 To lower the elevating legrest perform the following A Support user leg with one 1 hand B Push release lever downward with other hand C Gently lower user leg down and rest against the legrest Release Lever o 9 Support Tube FIGURE 6 4 Raising Lowering the Legrest Assembly Part No 1118386 37 P9000 XDT SECTION 7 ARMS SECTION 7 ARMS A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that on off switch on the joystick is in the off position Adjusting Armrest Height A WARNING Make sure the height adjustment lever is in the locked position before using the wheelchair NOTE For this procedure refer to FIGURE 7 1 1 Unlock the armrest by flipping the height adjustment lever on the top front of the armrest to the up horizontal position 2 Adjust armrest to one 1 of five 5 positions NOTE Height adjustment lever MUST be in the unlocked position when placing armrest into the arm assembly 3 Lock the armrest by pressing the height adjustment lever into the down vertical position when the desired armrest height is achieved 4 Repeat STE
63. tet decidere tidie erattu at Vu Krups ace ride du 66 Folding Ape nA 66 LIMITED WARRANTY 000000000000000000000000000000000000000000000000000000000000000000000 68 Part 1118386 5 P9000 XDT REGISTER YOUR PRODUCT REGISTER YOUR PRODUCT The benefits of registering Safeguard your investment Ensure long term maintenance and servicing of your purchase Receive updates with product information maintenance tips and industry news Invacare can contact you or your provider if servicing is needed on your product It will enable Invacare to improve product designs based on your input and needs UAWN Register ONLINE at www invacare com Complete and mail the form the next page Any registration information you submit will be used by Invacare Corporation only and protected as required by applicable laws and regulations P9000 XDT 6 Part No 1118386 Cut Along Line PRODUCT REGISTRATION FORM Register ONLINE at www invacare com or Complete and mail this form Name Address City State Province Zip Postal Code Email Phone No Fold OO here Invacare Model No Serial No Purchased From Date of Purchase Method of purchase check all that apply Medicare M Insurance Medicaid Other 2 This product was purchased for use by check one Self L Parent L Spouse L Other 3 Product was purchased for use at L Home Facility C Other 4
64. the batteries need to be charged more often or take longer to charge than normal they may need to be replaced Contact an Invacare dealer for service FIGURE 11 2 Connecting the Battery Charger Replacing the Batteries A WARNING Most batteries are not sold with instructions However warnings are frequently noted on the cell caps Read them carefully otherwise injury or damage can occur The use of rubber gloves and chemical goggles or face shields is recommended when working with batteries NOTE Invacare recommends that both batteries be replaced if one 1 battery is defective Recommended Battery Types A WARNING The warranty and performance specifications contained in this manual are based on the use of deep cycle gel cell or sealed lead acid batteries Invacare strongly recommends their use as the power source for this unit A CAUTION Failure to use the correct battery size and or voltage may cause damage to your wheelchair and give you unsatisfactory performance CHAIR SEAT QTY VOLTS BATTERY REMARKS WIDTH SIZE 18 inches 2 12 UI Deep Cycle 18 inches 2 12 Group 22NF Deep Cycle 1 Remove the battery boxes and tray from the wheelchair Refer to Removing Installing the Battery Boxes on page 50 and Installing Removing Battery Tray on page 51 Part No 1118386 49 P9000 XDT SECTION BATTERIES N Remove the existing batteries from the battery boxes Refer to Installing Removing Batteries I
65. ties in the presence of a qualified healthcare professional before attempting active use of the wheelchair P9000 XDT 12 Part No 1118386 SECTION GENERAL GUIDELINES DO NOT attempt to reach objects if you have to move forward in the seat DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down between your knees DO NOT lean over the top of the back upholstery to reach objects from behind as this may cause the wheelchair to tip over DO NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur Before attempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Turn both casters parallel to the object you are transferring onto Also be certain the power is off and the wheel locks are engaged to prevent the wheels from moving DO NOT engage or disengage the motor release levers until the power is in the off position Invacare strongly recommends proceeding down ramps or slopes at half speed or slower and to avoid hard braking or sudden stops DO NOT attempt to lift the wheelchair by lifting on any removable detachable parts Lifting by means of any removable detachable parts of a wheelchair may result in injury to the user or damage to the wheelchair Anti tippers MUST be used at all times When outdoors on wet soft ground or gravel surfaces anti tippers may not provide the same level of protection a
66. tns ntn sta ono 50 lnstalling Removing Battery ray dette easet tapete obey suse esrb 5 Installing Removing Batteries Into From Battery Boxes 52 Connecting Battery Cables 53 Direct Mount Method ttv bad pia tito d ia 54 Battery Clamp Methodi 57 Replacing Battery Box Retaining Strap eee eese esee tee ttente ton tonton tonta tentant 60 SECTION 2 CLUTCH MOTOR LOCK 00000000000000000000000000000000000000000000000 61 Engaging Disengaging the Clutches essen tenente tette ttnte ente te nente ntntenennne 6l SECTION 3 WHEEL LOCKS 000000000000000000000000000000000000000000000000000000000000 62 Installing Adjusting Using the Wheel Locks 62 Ire e 62 ocior een ntt tal cde stia dana ctu cis bub aM OR noD Ue E 63 SECTION 4 ANTI TIPPERS 00000000000000000000000000000000000000000000000000000000000 64 Installing Removing Adjusting 64 dris T 64 REMOVING c 64 Adjusting FCI RINE RTT 64 TRANSPORTING 0000000000000000000000000000000000000000000000000000000000000000000000000000 66 Transporting the P9000 repens 66 Unfolding Folding the Wheelchair eee eee tente ten tentent tantos tentata ttnnta tonus 66 at
67. tray and the adjustable end of the battery box retraining strap buckle 3 Feed the existing battery box retaining strap through the adjustable end of the battery box retaining strap buckle p Feed the existing battery box retaining strap through the slots in the battery box tray 5 Install the new battery box retaining strap by reversing STEPS 3 and 4 6 Reinstall the battery tray from the wheelchair Refer to Installing Removing Battery Tray page 51 Reinstall the battery boxes from the wheelchair Refer to Removing Installing the Battery Boxes on page 50 59 Adjustable Retaining Strap Buckle Retaining p Tray e N Retaining Slots Strap Battery Tray Retaining Strap FIGURE 11 10 Replacing Battery Box Retaining Strap P9000 XDT 60 Part 1118386 SECTION I2 CLUTCH MOTOR LOCK SECTION 2 CLUTCH MOTOR LOCK A WARNING After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result Engaging Disengaging the Clutches A WARNING DO NOT engage or disengage the clutches until the power is off NOTE For this procedure refer to FIGURE 12 1 The clutch engagement disengagement allows freewheeling or joystick controlled operation Freewheeling allows an attendant to maneuver the wheelchair without power To engage disengage the clutches 1 Locate the clutch handles
68. tray over the crossbrace bolt bushing under the seat upholstery of the wheelchair 2 Attach the hanger brackets to the wheelchair frame Key Slot Bracket Hanger Bracket Wheelchair Frame gt Crossbrace Bolt Bushing FIGURE 11 4 Installing Removing Battery Tray P9000 XDT Part No 1118386 SECTION BATTERIES Installing Removing Batteries Into From Battery Boxes A WARNING Make sure power to the wheelchair is OFF before performing this procedure The use of rubber gloves and chemical goggles or face shields is recommended when working with batteries Invacare strongly recommends that battery installation and battery replacement ALWAYS be done by a qualified technician After ANY adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result NOTE For this procedure refer to FIGURE 11 5 NOTE For changing or removing installing the battery boxes refer to Removing Installing the Battery Boxes on page 50 NOTE To remove the battery ies from the battery box es reverse the following procedure NOTE Have the following tools available COMMENTS Battery Lifting Strap See following note 1 2 inch 6 pt Box Wrench Not Supplied 7 16 inch 6pt Box Wrench Not Supplied 3 8 inch 6pt Box Wrench Not Supplied Diagonal Cutters Not Supplied NOTE The battery lifting strap supplie
69. trip e Only RED LED lit Battery charge is low Recharge as soon as possible NOTE Accurate readings are displayed when the joystick is in neutral Information Gauge FIGURE 11 1 When to Charge Batteries Part No 1118386 47 P9000 SECTION BATTERIES Charging Batteries A WARNING Never attempt to recharge the batteries by attaching cables directly to the battery terminals or clamps Use the recharging plug located on the front of the joystick DO NOT attempt to recharge the batteries and operate the power wheelchair at the same time During use and charging unsealed batteries will vent hydrogen gas which is explosive in the right concentration with air Follow the manufacturer s charging instructions A CAUTION Always charge new batteries before initial use or battery life will be reduced NOTE As a general rule batteries should be recharged daily to assure the longest possible life and minimize the required charging time Plan to recharge the batteries when it is anticipated the wheelchair will not be used for a long period of time The range per battery charge using recommended batteries should be approximately 5 to 9 hours of typical operation Extensive use on inclines may substantially reduce per charge mileage Description and Use of Battery Chargers The charger automatically reduces the charge from an initially high rate to a zero reading at a fully charged condition If left unattended t
70. tube into the mounting bracket 8 If the tie wraps securing the joystick control cord to the wheelchair were snipped at the beginning of this procedure re secure the cord to the wheelchair with new tie wraps in such a way that the control cord will not be pinched or cut during operation of the wheelchair Mounting Bracket Threaded Plate Arm Tube Hex Mounting Screws Adjustment Mounting Lock Lever Bracket et Joystick Mounting Tube FIGURE 9 2 Repositioning the Joystick Part No 1118386 45 P9000 XDT SECTION 10 SECTION 10 A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Before performing any maintenance adjustment or service verify that ON OFF switch on the joystick is in the OFF position A CAUTION As with any vehicle the wheels casters and tires should be checked periodically for cracks and wear and should be replaced Adjusting Forks NOTE For this procedure refer to FIGURE 10 1 1 Remove the dust cover from the caster headtube 2 To properly tighten caster journal system and guard against flutter perform following check A Remove battery boxes and battery tray from wheelchair Refer to Removing Installing the Battery Boxes on page 50 and Installing Removing Battery Tray on page 51 B Tip back the wheelchair to floor
71. vacare DOES NOT recommend the use of its wheelchairs as a weight training apparatus Invacare wheelchairs have not been designed or tested as a seat for any kind of weight training If occupant uses said wheelchair as a weight training apparatus Invacare shall NOT be liable for bodily injury and the warranty is void Weight Limitation The P9000 XDT has a weight limitation including seating system and accessories of 250 Ibs Refer to Percentage of Weight Distribution on page 23 Invacare recommends that only heavy duty wheelchairs should be used for individuals weighing more than 250 165 Further the activity level of the individual wheelchair user is important For instance a 170 Ib active wheelchair could subject the wheelchair to more stress than a 250 Ib user Invacare recommends that very active users consider the use of heavy duty wheelchairs P9000 XDT 16 Part No 1118386 SECTION 2 EMI INFORMATION SECTION 2 EMI INFORMATION A WARNING CAUTION IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC INTERFERENCE ON YOUR POWERED WHEELCHAIR Electromagnetic Interference EMI From Radio Wave Sources Powered wheelchairs and motorized scooters in this text both will be referred to as powered wheelchairs may be susceptible to electromagnetic interference EMI which is interfering electromagnetic energy EM emitted from sources such as radio stations TV stations amateur rad
72. vacare com P9000 XDT 2 Part No 1118386 TABLE OF CONTENTS TABLE OF CONTENTS REGISTER YOUR PRODUCT SPECIAL NOTES 9 TYPICAL PRODUCT PARAMETERS LABEL LOCATIONS SECTION GENERAL GUIDELINES 12 Controller Settings Repait or 12 Operating yack bte 12 Tire POSS Bcc Nah ee cone o adiit in od oben dU Sof ded stad ead Me Oed 14 El amp ctrical AGCeSSOLIBS 14 Batter OS fm Hc M 14 Charging 15 Grounding InstPuctlofis open oeeie eyiini a eben dia ees eias tidie ntes 15 Testi euo oro bad Gi noue aUe adeo ua aO uei l6 Mele Training aiii te mp ue teda de l6 bid didici l6 SECTION 2 EMI INFORMATION 00000000000000000000000000000000000000000000000000000 17 SECTION 3 SAFETY HANDLING OF WHEELCHAIR
73. wo prong receptacle replaced with a properly grounded three prong wall receptacle in accordance with the National Electrical Code If you must use an extension cord use ONLY a three wire extension cord having the same or higher electrical rating as the device being connected In addition Invacare has placed RED ORANGE warning tags on some equipment DO NOT remove these tags Part No 1118386 15 P9000 XDT SECTION GENERAL GUIDELINES Rain Test Invacare has tested its power wheelchairs in accordance with ISO 7176 Rain Test This provides the end user or his her assistant sufficient time to remove his her power wheelchair from a rain storm and retain wheelchair operation DO NOT leave power wheelchair in a rain storm of any kind DO NOT use power wheelchair in a shower or leave it in a damp bathroom while taking a shower DO NOT store power wheelchair in a damp area for an extended period of time Direct exposure to excessive rain or dampness may cause the chair to malfunction electrically and mechanically may cause the chair to prematurely rust or may damage the upholstery Check to ensure that the RED and GREY battery terminal caps are secured in place joystick boot is NOT torn or cracked where water can enter and that all electrical connections are secure at all times DO NOT use the wheelchair if the joystick boot is torn or cracked If the joystick boot becomes torn or cracked replace IMMEDIATELY Weight Training In
74. y terminal post is NOT mounted in the orientation shown in FIGURE 11 8 perform the following i Loosen the hex nut that secures the battery clamp to the POSITIVE battery terminal post A CAUTION When tightening the clamps always use a box wrench Pliers will round off the nuts NEVER wiggle the battery terminal s post s when tightening The battery may become damaged ii Remove the battery clamp from the POSITIVE battery terminal post iii Reposition the battery clamp on the POSITIVE battery terminal post as shown in FIGURE 11 8 iv Securely tighten the hex nut that secures the battery clamp to the positive battery terminal post If the battery clamp on the POSITIVE battery terminal post is positioned as shown in FIGURE 11 8 proceed to STEP 2 Part No 1118386 57 P9000 SECTION BATTERIES 2 Install battery clamp covers onto battery cables Detail C of FIGURE 11 9 RED battery clamp cover onto RED battery cable BLACK battery clamp cover onto BLACK battery cable A CAUTION When connecting the battery cable ring terminal s to the battery ies clamp s the battery cable s MUST be connected in the position shown in Detail of FIGURE 11 9 Otherwise damage may occur to the battery cable and or battery clamp covers 2 gt m N Connect battery cable s to battery ies terminal s post s as shown in Detail A of FIGURE 11 9

P9000™ XDT

Contents

Download Pdf Manuals

Related Search

Related Contents

P9000&trade; XDT

Contents

Download Pdf Manuals

Related Search

Related Contents

P9000™ XDT