INSTALLATION INSTRUCTIONS
Contents
1. WAC U RA Accessory Application Publications No INSTALLATION STEERING WHEEL 2015 TLX Issue Date INSTRUCTIONS P N 08U97 TZ3 200 PARTS LIST Illustration of the Steering Wheel in the Vehicle Steering wheel 2 TORX bolts Steering wheel bolt STEERING QC02801AB WHEEL U INSTALLATION Client Information The information in this installation Information dahada i instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers NOTE TOOLS AND SUPPLIES REQUIRED e Observe all safety notes and precautions in the Service Sa Manual in addition to those in this Installation Phillips screwdriver Instruction 10 mm Open ene wrench e Do not damage the vehicle 10 mm Hex bit 1 Turn the steering wheel so the front wheels are Ratchet pointing the straight ahead T30 TORX bit 2 Disconnect the negative cable from the battery Torque wrench Steering wheel puller HDS MVCI Shop towel The following tools are available through the Honda Tool and Equipment Program On the iN click on Service gt Service Bay gt Tool and Equipment Program then enter the number under Search Or call 888 424 6857 e Plastic Trim Tool T N SILTRIMTL10 e Trim Tool Set T N SOJATP2014 2014 American Honda Motor Co Inc All Rights Reserved BII 51457 14072. the Service Manual if necessary Make sure the steering wheel is in the straight ahead position and that the front wheels are pointing straight ahead if not adjust the front toe as described in the Service Manual 7 of 7
3. 08U97 TZ3 2000 90 1 of 7 3 2 of 7 STEERING WHEEL Remove the two TORX bolts 4 Unplug the two vehicle 2 pin connectors pull up on the locking tabs and the vehicle 1 pin connector NOTE Be careful not to damage the connectors 2 VEHICLE 2 PIN CONNECTORS ane TABS Pull up 2 TORX BOLTS Do not reuse QC02802AB AIRBAG STEERING WHEEL QC02803BB 5 Remove the airbag Do not drop the removed airbag or hit it on an object Place the removed airbag ona pad surface with the top facing upward BII 51457 1407 2014 American Honda Motor Co Inc All Rights Reserved 6 With the front wheels pointing straight ahead unplug the vehicle 20 pin connector from the cable reel and loosen the steering wheel bolt STEERING WHEEL PULLER STEERING WHEEL BOLT Loosen STEERING WHEEL PULLER BOLT VEHICLE 20 PIN CONNECTOR STEERING WHEEL STEERING WHEEL BOLT Do not reuse QC02804AB 7 Using a steering wheel puller release the steering wheel Do not thread the steering wheel puller bolts in more than 5 mm 0 2 in When removing the steering wheel take care not to move the front wheels 8 Remove the steering wheel bolt then remove the steering wheel 2014 American Honda Motor Co Inc All Rights Reserved BII 51457 1407 9 Remove the body cover STEERING WHEEL 2 RETAINING TABS BODY COVER 2 SELF TAPPING SCREWS 2
4. 2PINS CLIP qcoo907a8 2014 American Honda Motor Co Inc All Rights Reserved BII 51457 1407 5 of 7 20 6 of 7 Before installing the steering wheel make sure the front wheels are pointing straight ahead then center the cable reel Do this by first rotating the cable reel clockwise until it stops then rotate it counterclockwise three full turns The arrow mark on the cable reel should point straight up Rotate counterclockwise about three full turns until the arrow mark points up ARROW Rotate clockwise until it stops QC02908AB 21 22 BII 51457 1407 Install the new steering wheel on the steering column shaft in the straight ahead position e Route the two vehicle 2 pin connectors through the opening in the new steering wheel e Plug the vehicle 20 pin connector to the cable reel e Check that the wire harnesses are not pinched STEERING PIN COLUMN SHAFT NEW STEERING WHEEL 2 VEHICLE 2 PIN CONNECTORS STEERING WHEEL ee J NEW STEERING WHEEL BOLT Torque 44 54 N m 4 5 5 5 kgf m 32 40 Ibf ft VEHICLE 20 PIN CONNECTOR QC02909AB Install the new steering wheel bolt Torque the steering wheel bolt to 44 54 N m 4 5 5 5 kgf m 32 40 Ibf ft 2014 American Honda Motor Co Inc All Rights Reserved 23 Install the airbag on the new steering wheel with two 24 new TORX bolts plug in the two vehicle 2 pin connectors and one vehicle 1 pin conne
5. PINS CLIP QC02805AB 10 Remove the left and right paddle shifters from the steering wheel 4 SCREWS LEFT PADDLE SHIFTER RIGHT PADDLE SHIFTER STEERING WHEEL VEHICLE CONNECTORS QC02806AB 3 of 7 11 Remove the screw s 13 Remove the switch assembly and cable guide STEERING WHEEL GROUND TERMINAL one Do not reuse STEERING TET WHEEL SCREW SWITCH ASSEMBLY if equipped QC02807AB AND CABLE GUIDE QC02902AB 12 Remove the self tapping screws 14 Install the switch assembly and cable guide on the new steering wheel 6 SELF TAPPING SCREWS NEW STEERING 4 RETAINING WHEEL TABS STEERING WHEEL QC02901AB SWITCH ASSEMBLY AND CABLE GUIDE ACO2OAE 4of7 BII 51457 1407 2014 American Honda Motor Co Inc All Rights Reserved 15 Secure the switch assembly and cable guide to the 17 Install the left and right paddle shifters new steering wheel with the self tapping screws 4 SCREWS TAPPING LEFT PADDLE NEW STEERING TAPPING Sa WHEEL w SCREWS t SHIFTER RIGHT PADDLE SHIFTER NEW STEERING WHEEL SWITCH ASSEMBLY VEHICLE AND CABLE GUIDE QC02904AB CONNECTORS QC02906AB 16 Install the screw s and ground terminal 18 Plug the two connectors into the left and right paddle shifters NEW STEERING GROUND Eee See 19 Install the body cover on the new steering wheel NEW STEERING WHEEL BODY COVER SCREW if equipped QC02905AB TAPPING SCREWS
6. ctor 25 e Alternately tighten the right and left TORX bolts 26 so that the gaps on the right and left sides l 27 between the horn pad and the steering wheel are even Torque the TORX bolts to 28 6 9 11 8 N m 0 7 1 2 kgf m 5 1 8 7 Ibf ft e TORX bolts are coated with non hardening thread lock sealant so they cannot be reused When installing the steering wheel be sure to replace the TORX bolts with the ones included in this kit 2 VEHICLE 2 PIN VEHICLE 1 PIN yew 29 CONNECTORS CONNECTOR STEERING WHEEL 30 31 32 2 NEW TORX BOLTS 69 118 N J i m AIRBAG 0 7 1 2 kgf m 5 1 8 7 Ibf ft QC02910AB HORN PAD 2014 American Honda Motor Co Inc All Rights Reserved BII 51457 1407 Check that all wire harnesses are routed properly and all connectors are plugged in Reconnect the negative cable to the battery Reinstall all other removed parts Connect the HDS MVCI and clear the DTCs Inspect the following items If any abnormality is found perform troubleshooting as described in the Service Manual e Press the engine start stop button to the ON mode The SRS indicator should come on for about 6 seconds and then go off e Make sure the horn and steering wheel switches work properly Press and hold the radio power button for two seconds to restore the radio and navi if equipped system functions Reset the clock on vehicles without navigation Restore the systems to normal operation as described in
Download Pdf Manuals
Related Search