manual mw-80H - ingles - World of Rock Drills International
Contents
1. Characteristi Ie OF 90 F re 20 F aracteristic i 90 9 Procedure 7 0 to32 C 32 C Viscosity 175 min SUS at 100 F 38 C ASTM D2161 46 min 450 min 750 min SUS at 210 F 99 C ASTM D2161 37 min 65min 85 min CST at 104 F 40 C ASTM D445 6 min 105 min 160 min CST at 212 F 100 C ASTM D445 10 F 11 min 16 min Pour Point F C max ASTM D97 23 C 10 F 0 F 370 F 23 C 18 C Flash Point F C min ASTM D92 188 C 400 F 450 F 90 204 C 232 C Viscosity Index min ASTM D2270 1200 90 90 Steam Emulsion No Min ASTM 1935 Stringy 1200 1200 Consistency 65 2000 Ibs Stringy Stringy Falex Load Test lbs kg 907 kg 2000lbs 2000 lbs min ASTM D2670 907 kg 907 kg 30 Ibs 30 Ibs 30 Ibs Timken E P Test lbs kg ASTM D2782 14 kg 14 kg 14 kg min Table 2 Selection Chart Typical Operating Conditions Below 20 F 20 F to90 F Above 90 F 7 C 7 C to 32 C 32 C 100 150 psi 7 03 10 5 Light Medium Heavy kg cm 6 7 DRILL STEEL THREAD LUBRICANT It is very important that the threads of all striking bars drill rods couplings and bits be properly lubricated and cared for at all times Proper lubrication will result in longer life and will simplify threading and unthreading drill rod joints Use a good molybdenum di sulphide type thread grease such as 6 8 MAINTENANCE To ensure maximum life and top perfor2. 3 Remove drill steel clean out passages 4 Drifter and steel not aligned 4 Check alignment while drilling to with hole steel or bit binding prevent binding and to avoid stuck in hole steel 5 Worn fronthead 5 Check chuck end components components and replace if necessary 6 Incorrect feed pressure 6 Adjust feed pressure 7 Accumulators not properly 7 Bleed and recharge charged accumulators 26 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H Stuck steel 1 Driving steel after bit is dull 1 Don t force a dull bit sharpen or or has lost its gauge replace with new bit 2 Crowding bit in soft 2 Use down pressure cautiously in formations soft formations be certain steel is rotating freely 3 Cuttings not being blown 3 Use blow air continuously from hole 4 Misalignment of steel with 4 Keep drill steel and hole in hole causing binding alignment at all times Chipping or 1 Bad striking bar which is 1 Take bad striking bar out of breakage of piston too hard or rounded on end service one bad striking bar can allowing minimum contact with damage other parts piston striking face 2 Worn chuck end 2 Replace worn components components which permit striking bar to cock in chuck so that piston strikes shank a glancing blow 97 WOLF Metal rg
3. Refer to drilling machine instruction manual for time intervals for checking oil reservoir Keep the lubricator well supplied with oil at all times e Always keep the drifter aligned with the drill steel and hole This assures straight and true holes that go in fast Most importantly this prevents unnecessary wear and damage to the drill f Always use the centralizer to guide the drill steel during the drilling operation 5 14 DRILL STEEL CARE a It is very important that the threads of the drill steel be properly lubricated and cared for at all times Steels having stripped threads cracks or severe galling must not be used Also care should be taken while drilling not to bend steel or gall threads due to misuse 14 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H b Bent steel produces unnecessary stresses and accelerates wear on all fronthead components Bent steel and severe thread galling can be avoided if the following steps are taken c Be sure that the steel is bottomed in the striking bar couplings and bit d All threads must be in good condition and well greased e Always drill with a sharp bit no more than 1 8 in 3 175 mm flat on carbides Dull bits cause excessive pounding and unnecessary stresses on all threads and drifter fronthead parts f Approach the rock at reduced feed pressure position ca
4. and bit Timing parts include the geroler valve drive valve plate and valve c First Timing Step Locate the largest pocket in the geroler and mark it on the outside edge of the geroler proceed as follow 2 Install the valve drive in the geroler gt Install the seal in the groove in the valve plate Align the case drain holes in the geroler and valve plate and install the valve plate seal side toward the geroler against the geroler J4 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H gt Second Timing Step Locate the slot opening in the valve plate 7 which is in line with the largest open pocket in the geroler 5 gt Third Timing Step Locate any one of the side openings that goes through the bottom face of the valve 8 Line up this side opening with the open slot of the valve plate 7 that is in line with the largest open pocket of the geroler 5 Rotate the valve 8 clockwise until the spline teeth engage FN CAUTION INSTALL THE FACE SEALS IN THE POSITION OR THE MOTOR WILL NOT OPERATE PROPERLY DO NOT FORCE OR BEND THE FACE SEALS ANY DAMAGE TO THESE SEALS WILL ADVERSELY AFFECT THE OPERATION OF THE MOTOR MAKE SURE THAT THE SEALS ARE FIRMLY SEATED 6 14 INSPECTION OF ACCUMULATOR PRESSURES yN CAUTION THE DRIFTER ACCUMULATORS MUST BE CHECKED EVERY 250 HOURS OF OPERATION TO MAKE SURE THE PRES
5. x With the gear box on a suitable fixture cylinder side down use a hammer and appropriate drift to drive the front liner out of the gear box y With the gear box on a suitable workbench cylinder side up use a hammer and appropriate drift to drive the bushing out of the gear box z Unscrew the twelve bolts which hold the three accumulators to the cylinder and remove the accumulators from the cylinder y XI BE SURE TO BLEED THE ACCUMULATORS BEFORE ANY ACCUMULATOR DISASSEMBLY IS ATTEMPTED aa Put the accumulator in a vise and with a spanner wrench remove the cap from the accumulator cover bb Loosen the accumulator valve slightly to bleed the gas from the accumulator cc Unscrew the cover from the accumulator bogy dd Remove the diaphragm from the accumulator body ee Remove the two seals from the cylinder liner seals from the back liner and seal wiper ring from the front liner NOTICE Do not remove the cylinder liner unless service is required on the liner ff If necessary to remove the cylinder liner insert and appropriately sized tool into the cylinder and drive the cylinder liner out with a large hammer or press NOTICE Do not remove any of the bushings unless they require servicing 20 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H gg Place the chuck end on an appropriate fixture so that
6. WOLF Metal rgica cost and expense for the repair The customer shall take care of normal needs of the equipment including supplying fuel grease tires oils cooling system water recharging batteries etc The customer will perform any other routine service and preventive maintenance set forth in the Operators Service Manual for the equipment If the customer requires for further assistance or service from the factory the cost is for customer account Written permission of any warranty claim return must be first obtained from authorized WOLF personnel All returns must be accompanied with a complete written explanation of claimed defects and circumstances of operational failure 22 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H Products manufactured or sold by WOLF are not warranted expressly or implication for merchantability or fitness or for any measure of service or suitability of for a specific purpose notwithstanding any disclosure to WOLF of the use to which the product is to be put This express warranty is to solve warranty of WOLF there are no warranties which extend beyond the warranty herein expressly set forth The sales of products of WOLF under any other warranty or guarantee express or implied is not authorized This Warranty shall not apply to any WOLF Metal rgica product which shall have been altered or m
7. interference Repair or replace Drifter lacks power 1 Low hydraulic oil flow 1 Increase flow setting hydraulic supply pressure normally above 1991 psi 140 kg cm 2 Leaking seals or o rings 2 Check for tightness of hardware If necessary visually inspect seals 3 Piston not hitting striking bar 3 Check for excessively worn at full blow striking bar splines or striking bar seat and replace if necessary Replace striking bar if shank end is excessively worn 1 Uneven tension on nuts or 1 Nuts must be tight and under loose nuts equal tension Tighten the nuts gradually and alternately Apply 325 Ib ft 441 Nm of torque to nuts No steel rotation or 1 Steel binding in hole 1 Sharpen or replace worn bits rotation is weak Apply correct amount of down pressure and keep drill steel and hole in alignment 2 Worn or leaking rotation 2 Repair or replace motor motor 2 Incorrectly assembled 3 Check for proper assembly of chuck drive gear components the chuck drive gear components or excessively worn and for excessively worn components components 4 One through bolt broken 4 Replace broken through bolt causing chuck end binding Apply 360 Ib ft 488 Nm of torque to both nuts TROUBLE PROBABLE CAUSE REMEDY Slow drilling speed 1 Dull bit 1 Replace bit 2 Cuttings not being removed 2 Increase blow air or water to from hole keep bit working on fresh rock 3 Plugged drill steel
8. supply to exhaust This action produces a high frequency reciprocating action of 2600 cycles per minute The piston strikes the striking bar on each forward power stroked and through the striking bar and steel drives the drill bit into the rock at 2600 blows per minute 5 7 DRILL STEEL ROTATION The drifter is designed with an independently controlled hydraulic powered rotation motor that provides continuous drill steel rotation forward or reverse The motor converts hydraulic fluid to rotation power and transmits the rotation power to a drive gear which is part of the spur gear train housed in the drill fronthead Thus as the drive gear is rotated the meshing chuck gear and mating chuck driver follow the rotation Splines within the chuck driver mate with those in the striking bar thereby imparting the rotation through the drill steel to the bit 5 8 OPERATING CONTROLS Hammer action drill steel rotation and feed are controlled separately and each must be regulated for optimum results in the drilling conditions encountered All operating controls for the drifter are located on the drilling machine console Refer to the operation section of the drilling machine instruction book for detailed descriptions and instructions covering all operating controls and gauges 5 9 CHARGING THE DRIFTER ACCUMULATORS The drifter uses nitrogen accumulators to dampen vibrations in the pressure and return hoses Before operating the drifter both accu
9. the bushing can be driven out from the chuck side of the chuck end hh Remove the chuck bushing and cap liner if necessary 6 10 HYDRAULIC ROTATION MOTOR DISASSEMBLY a b 953 ATT roA p q NOTICE Clean the exterior of the motor Cleanliness is extremely important when repairing the hydraulic rotation motor Work in a clean area Drain the oil from inside the motor Place the motor in a vise with the output shaft down yN CAUTION CLAMP ACROSS THE MOUNTING FLANGE AREA OF THE BEARING HOUSING EXCESSIVE CLAMPING PRESSURE WILL CAUSE DISTORTION WHEN CLAMPING USE SOME PROTECTIVE DEVICE ON THE VISE SUCH AS SPECIAL SOFT JAWS OR PIECES OF HARD RUBBER OR BOARD Unscrew the four bolts and lift the valve housing straight up NOTICE If done carefully the pins springs balance plate and valve will remain on the valve plate Carefully remove the o ring from the valve housing Remove the two pins and springs from the balance plate Remove the balance plate valve and inner and outer face seals Lift the valve plate away from the geroler Carefully remove the o ring from the valve plate Lift the valve drive out of the geroler Remove the geroler Be sure to retain the rollers in the outer ring if they are loose Pull the drive away from the wear plate Carefully remove the o ring from the wear plate Lift the wear plate away from the bearing housing Remove the shaft face seal from the wear plate Remove th
10. 0 O 6 10 Hydraulic Rotation Motor Disassembl 6 11 Inspections of Parts 6 11 Inspections of Parts sd 6 12 Accumulator Reassembl 6 13 Hydraulic Rotation Motor Reassembl 6 14 Inspection of Accumulator Pressures 7 Troubleshooting siz 7 Troubleshooting h NIN 5 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H 1 INTRODUCTION This instruction manual contains information for safety operation maintenance service information troubleshooting for the drifter MW 80H here after referred to as drifter 2 ABBREVIATION LIST Abbreviation Symbol or Term Meaning F Hydraulic Oil M nstruction Manual O Kilometer M 1 Meter MO J p JMotrOl Newton Meter Pp artist RD JRoecDilOl 3 SAFETY FIRST 6 E WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H This section contains important information for the Top Hammer MW 80H here after referred to as drifter Safety First is the primary concern for the protection of both personnel and the machine during any phase of operation All personnel must thoroughly understand all safety precauti
11. 40 kg cm WOLF hydraulic crawler machines are designed to use this hydraulic drifter Basically its hydraulic system contains a fluid reservoir which stores a supply of hydraulic oil pumps which develop and deliver the required hydraulic oil pressure and flow to operate the drifter and its rotation motor filters for removing particulate contamination from the oil supply control valves to initiate hammer action and control the speed and direction of the rotation motor and an oil cooper to maintain the entire system at an optimum operating temperature An arrangement of hoses and fittings carries the oil from the reservoir through the pumps and regulating controls to the drifter and rotation motor and back to the reservoir through the oil cooler 5 2 LUBRICATION REQUIREMENTS The Drifter uses an oil mist to provide lubrication to all critical points in the front end of the drifter A 3 8 in 9 5 mm diameter hose connected to the drifter carries the oil laden air from a lubricator part of drilling machine to the front end of the drifter The amount of lubrication provided is controlled by the lubricator located on the drilling machine 5 3 AIR REQUIREMENTS The air requirements for the drifter are for front end lubrication and hole cleaning For normal drilling conditions a minimum flow of 10 scfm 0 28 m3 min at a pressure of 100 psi 7 03 kg cm is required for lubrication and the remaining air for hole cleaning 5 4 HOSES AND F
12. E This data based on hydraulic supply of 29 27 gpm 110 liters min at 1991 psi 140 kg cm at the inlet Rotation Motor Specifications Metric Diameter of Hydraulic Hoses 2 Ve in 12 7 mm Stall Torque at Chuck 427 lb ft 578 Nm Rotation Speed at Chuck Normal Operating 0 to 150 rpm Speed 150 rpm Maximum Chuck Rotation Speed Free Speed NOTICE This data based on hydraulic supply at 11 89 gpm 45 liters min at 1991 psi 140 kg cm at the inlet Shipping Information O US Net Weight of Drifter esesesesseseseseeseess 463 lbs 210 Kg Shipping Weight 483 lbs 219 Kg 5 REQUIREMENTS 10 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H This section provides air requirements operating principles hydraulic requirements and lubrication requirements of the Hydraulic Drifter MW 80H hereafter referred to as drifter 5 1 HYDRAULIC REQUIREMENTS The hydraulic power required to operate the drifter is divided into two independent functions a Hammer Operation The hydraulic system must be capable of supplying hydraulic fluid to the drifter at a rate of 29 27 gpm 110 liters min at 1991 psi 140 kg cm b Drill Steel Rotation The Hydraulic system must be capable of supplying hydraulic fluid to the rotation motor on the drifter at a rate of 11 89 gpm 45 liters min at 1991 psi 1
13. ITTINGS Only quality hose designed especially for rock drill service should be used It should be constructed with an outer covering which resists abrasive wear and have a working pressure safety factor of at least 4 to 1 in relation to burst Hoses and hose fittings must be in good condition and the fittings must be kept tight The following lists the hoses required to operate the drifter and the diameter of each hose Inlet Hydraulic Hose 34 in 29 mm diameter Return Hydraulic Hose 34 in 19 mm diameter Forward Rotation Hydraulic Hose 1 2 in 12 7 mm diameter Reverse Rotation Hydraulic Hose 1 2 in 12 7 mm diameter Front End Lubrication Hose 3 8 in 9 5 mm diameter eae se 1 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H 5 5 BASIC OPERATING PRINCIPLES The operation of the drifter is based on two independent basic operating principles a the principle that causes the piston to reciprocate hammer action and b the principle governing the drill steel rotation 5 6 DRILL PISTON RECIPROCATION The drifter is a valved hydraulic drill The valve cylinder assembly and cylinder liner convert hydraulic fluid pressure into efficient hammer action The piston within the cylinder liner provides the impact force which is transmitted to the drill steel The valve alternately switches pressure from
14. Instruction Manual MW 80H INSTRUCTION MANUAL For HYDRAULIC DRIFTER Read this Instruction Manual before operating this equipment a Equipamentos Pneum ticos e Hidr ulicos 2 ee WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H WARRANTY WOLF Metal rgica warrants that all replacement parts supplied by it will be free from defects in materials and workmanship for a period of three months from date of supply when operating under normal working and environmental conditions If a failure occurs which is due to defects in materials or workmanship during the period WOLF Metal rgica will replace the item This Warranty shall not apply to any WOLF Metal rgica product which shall have been altered or modified in any way We shall not in any event be liable for the cost of any special indirect or consequential damage to any one WOLF will provide a new part or repaired part at its election in place of any part which is found upon its inspection to be defective in material and workmanship during the period prescribed above All warranty parts will be replaced FOB Wolf factory in Indaiatuba SP Brazil This warranty does not apply to failures occurring as a result of abuse misuse negligent repairs corrosion erosion and normal wear and tear alteration or modification made to the product without express writt
15. Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H Unscrew and remove the four through bolt nuts and pull the four through bolts out of the drifter m Using a plastic hammer drive off the chuck end n Pull the chuck driver out of the gear box o Unscrew the four capscrews which hold the hydraulic motor to the gear box p Pull the hydraulic motor out of the gear box q Unscrew the four bolts and remove the cover and o rings r Use two wooden blocks to support the cylinder so that the backhead 1 can be removed with a plastic hammer s From the chuck end of the drifter strike the front surface of the piston with a hammer and plastic drift Drive the piston valve valve guide and cylinder back liner out of the cylinder until they can be pulled the rest of the way out by hand t Using both hands pull the piston valve valve guide and cylinder back liner the rest of the way out of the cylinder u Using one of the cover bolts to insert into the gear shaft pull the gear shaft out of the gear box Support the idler gear with the other hand so that it will not drop when the gear shaft is pulled out v Separate the gear box from the cylinder with a plastic hammer w Set the gear box on its chuck side From the backhead side of the gear box use a hammer and suitable steel bar to drive the drive gear and bearings from the gear box
16. N The drifter uses two nitrogen charged diaphragm accumulators to dampen vibrations in the supply and return hoses The supply line high pressure accumulator must be charged to 853 psi 60 kg cm The return line low pressure accumulator must be charged to 57 psi 9 amp WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H 4 kg cm An accumulator charging kit is furnished as a standard accessory item with the hydraulic machine The drifter is designed with chuck parts to accommodate a 6 splined striking bar A striking bar is not furnished as standard equipment with the drifter 4 2 SPECIFICATIONS Tables below show specifications for the drifter Net Weight 463 Ib 210 Kg Overall Length less striking bar 40 35 in 1025 mm Overall Width 14 17 in 360 mm Overall Height 11 61 in 295 mm Drill Hammer Hydraulic Operating Pressure 1991 psi 140 kg cm Hammer Blows Per Minute variable 2600 bpm 2600 bpm Diameter of Drill Inlet Hydraulic Hose 3A in 19 mm Diameter of Blower Hose 34 in 19 mm Diameter of Front End Lubrication Hose 3 8 in i 5 mm Supply Accumulator Charge Pressure Drifter 853 psi 60 kg cm Return Accumulator Charge Pressure Drifter 57 psi 4 kg cm Supply Accumulator Charge Pressure Reverse 853 psi 60 kg cm Percussion Return Accumulator Charge Pressure Reverse 853 psi 60 kg cm Percussion NOTIC
17. S OR SIGNS OF EXCESSIVE WEAR WHEN PRESSURIZED A DAMAGED ACCUMULATOR COULD BURST SCATTERING METAL FRAGMENTS THROUGHOUT THE AREA WHICH COULD SEVERELY INJURE PERSONNEL i BE SURE TO BLEED THE ACCUMULATORS BEFORE ANY ACCUMULATOR DISASSEMBLY IS ATTEMPTED 8 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H 4 INTRODUCTION This section provides a description and specifications of the Hydraulic Drifter MW 80H hereafter referred to as drifter 4 1 DESCRIPTION The hydraulic drifter is a valved hydraulically operated hammer drill that incorporates and integral independently controlled hydraulically powered rotation motor to rotate the drill steel and bit The drifter is capable of drilling 3 to 4 in 76 to 100mm diameter holes in all types of rock formations It is especially suitable for pipeline work drilling vertical and angle blast holes in quarries and on any construction jobs where large volume rock excavations are required Since the drifter is hydraulic there are only two moving parts to control hammer action the piston and the piston valve The piston provides the impact force which is transmitted to the drill steel The valve alternately switches pressure from supply to exhaust This action produces a high frequency reciprocation of 2600 cycles per minute The piston strikes the striking bar on each forwa
18. SURES ARE CORRECT FOR THE CORRECT ACCUMULATOR PRESSURES AND BELOW FOR THE PROCEDURE FOR CHECKING THESE PRESSURES Using the furnished accumulator charging kit check the accumulator pressures as follows a Using the spanner wrench furnished with the drifter remove the protective caps from the accumulator covers on both accumulators b Loosen the accumulator valve slightly about an 1 8 of a turn c Attach the accumulator valve assembly to the accumulator turning the assembly hand tight d Check the pressure gauge on the accumulator charging assembly e If the accumulator pressure are incorrect refer to above topic 7 TROUBLESHOOTING Troubleshooting will be accomplished by using the table provided in this section Table 1 will provide a step by step question and remedy Using both of these together will solve most common problems Table 1 Troubleshooting PROBABLE CAUSE REMEDY Drifter will not start 1 Could Hydraulic oil or wrong 1 Never use hydraulic oil that does hydraulic oil not conform to the specifications outlined Table 1 If ambient temperature is below 32F 0C drill may be reluctant to start but it will start if control valve is left in the position for a few minutes 2 Drifter valve stuck 2 Check valve for scoring burrs 25 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H or mechanical
19. Y OFF THE TOOL WHIP AROUND AND CAUSE INJURY TO THE OPERATOR 6 3 DRIFTER a Never allow the hose adapters on the drifter to remain uncapped Dirt contamination of the drifter will cause accelerated wear and drifter failure b Be certain that the striking end of the striking bar is square flat and free of all sharp edges The striking bar should be repaired or discarded if cracked peened or crowned 16 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H c Be sure that the hole in the drill steel is open d Excessively dull bits cause slow drilling and excessive pounding within the drifter Always change the bit when there is an appreciable drop off in drilling speed or any noticeable change in the action of the drifter e Be certain that the drifter front end parts are well lubricated Oil must be detected on the striking bar for proper rotation of lubricating oil provided is controlled by air and oil regulators located at the drilling control console on the drilling machine Adjust the oil flow so that the striking bar always shows an oil film Refer to drilling machine instruction manual for time intervals for checking oil reservoir Keep the lubricator well supplied with oil at all times Keep the lubricating oil free of dirt f Schedule regular periods for checking front end lubrication Do not wait for physical evidenc
20. all connections Make sure that all threads are clean and free of dirt and coated with a high pressure grease or equivalent each time they are coupled or stored b Remove the two chuck end cap bolts and nuts c Remove the chuck end cap cap liner and o ring d Make sure the striking bar is equipped with a seal and the lip of that seal is facing the striking bar splines e Coat the striking bar with clean oil and insert the shank end of the striking bar into the chuck f Insert the chuck end cap liner o ring and chuck end cap and secure with two chuck end cap bolts and nuts 5 11 DRILLING PROCEDURES Detailed operating and drilling instructions are covered in the operation section of the drilling machine instruction book 5 12 DRILLING TIPS To ensure maximum operating efficiency the following suggestions should be observed 5 13 SUGGESTIONS FOR DRILLERS a Never pound on stuck steel Nothing is accomplished thereby and the drifter and bit may be permanently damaged in the process b Never strike the drifter with tools C Every effort must be made to keep dust and dirt from entering the drifter Preventing impurities from entering the drifter pays off in improved operation and reduced down time for repairs d Always be sure the drifter front end parts are well lubricated Oil must be detected on the striking bar of proper rotation component lubrication Adjust the oil reservoir so that the striking bar always shows an oil film
21. e o ring from the bearing housing NOTICE You may need a press to remove the shaft bearing kit from the bearing housing Remove the shaft bearing kit from the bearing housing Use a small screwdriver to remove the shaft oil seal and dust seal from the bearing housing 2 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H FN CAUTION BE CAREFUL NOT TO DAMAGE THE BORE OF THE BEARING HOUSING 6 11 INSPECTION OF PARTS The operating performance of the drifter depends on the condition in which the working parts are maintained When it is necessary to disassemble the drifter for repairs all parts should be inspected for wear and damage and replacement parts installed when necessary a Hydraulic Rotation Motor a Clean all metal parts in clean solvent and blow dry with air Do not wipe dry with a cloth or paper towel because lint or other matter can get into the motor and cause damage b Check all matting surfaces Replace any parts that have scratches or burrs that could cause leakage Do not use a coarse grit or try to file or grind these parts c Check around the chamfered area of the shaft for burrs nicks or sharp edges that damage seals when reassembling b Cylinder Inspect cylinder bore for scratches gouges and galling repair any of these irregularities c Backhead Inspect the front face the face
22. e of poor lubrication g The drifter fronthead should be taken apart periodically cleaned and parts inspected for wear and distortion h Hydraulic seals and o rings wear during normal operation Hydraulic oil leakage may be and indication that seals or o rings need to be replaced i If a drifter is not operating properly investigate the problem as described in Section 6 covering Troubleshooting 6 4 LUBRICANT SPECIFICATIONS The Topic outline the lubricants required for the drifter 6 5 HYDRAULIC OIL Refer to the instruction manual for the drilling machine for the specifications of the hydraulic oil 6 6 FRONT END LUBRICATING OIL yN CAUTION KEEP THE ROCK DRILL LUBRICANT CLEAN AND FREE FROM ALL FOREIGN MATTER TO PREVENT TO THE INTERNAL PARTS The rock drill oil used in the air line lubricator must be a well refined petroleum lubricating oil It must be suitably compounded to provide the specified consistency and film strength and the further compounded to provide the specified steam emulsion number which is required to provide satisfactory lubricant Though the composition of the film strength additive is not specified it must be non corrosive to both steel and bronze and contain little or no sulphur 17 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Table 1 Rock Drill Oil Specifications Instruction Manual MW 80H
23. e to open the accumulator valve Open valve three to four turns NOTICE Failure to open the accumulator valve a full three to four turns may result in damage to the seal when the nitrogen bottle valve is opened g Slowly open turn counter clockwise the valve on the nitrogen bottle and allow the pressure to build Close the valve when the pressure reaches proper setting If the pressure becomes higher adjust the pressure by using the discharge valve on the charging valve assembly h Close the accumulator valve by turning the charging valve on the charging valve assembly i Open the discharge valve to release gas in the charging valve assembly and the hose j Remove the nitrogen bottle hose k Remove the charging valve assembly 1 Tighten the accumulator valve Torque the valve to 22 lb ft 30 Nm m Replace the accumulator protective cap n Follow the same procedure to charge the second accumulator The drifter is then ready for service 5 10 CONNECTING THE STRIKING BAR a Make sure all striking bars and threaded accessories are properly greased 13 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H NOTICE It is very important that all threaded accessories be properly lubricated and cared for at all times Proper lubrication will result in longer part life and will simplify threading and unthreading of
24. en consent of WOLF Metalurgica or failure to follow the recommend operating practices and maintenance procedures as provided in the product s operation and maintenance publication Equipment and part furnished by WOLF Metalurgica but manufactured by others shall carry whatever warranty the manufactures have conveyed to WOLF Metal rgica and which can be passed on to the initial user Wolf Metal rgica shall not be liable for loss of time manufacturing cost labor material loss of profit consequential damages direct or indirect because of defective products whether due to right arising under the contract of sale or independently thereof and whether or not such claim is based on contract tort or warranty The customer agrees to care for the equipment properly to use it within its rated capacity to restrict its use to the customer s qualified personnel and to prohibit anyone other than the buyer s qualified mechanic from making repairs to modifying or adjusting the equipment The customer assumes full responsibility for damage loss or destruction of the equipment from the date of delivery The customer at his own expense shall maintain the equipment and replace or change all spare parts or perform all necessary labor according to the equipment s Operators Service Manual The customer further agrees to pay for all damage to the equipment resulting from causes other than normal wear and tear upon receipt of invoice from the
25. ent upon the condition in which the working parts and interacting systems are maintained The following areas must be included in a preventive maintenance check list to assure reliable and consistent drifter operation 6 1 HYDRAULIC SYSTEM Clean hydraulic oil is the life blood of the drifter Without an adequate supply of clean oil of proper weight at the correct pressure and temperature the drill cannot operate properly a Make sure the hydraulic oil is kept free of dirt Check that all filters are properly installed and serviced regularly b Hydraulic oil conforming to the specifications as outlined in the drilling machines instruction manual c Maintain the correct level of hydraulic fluid in the hydraulic oil reservoir to prevent overheating and foaming d Make sure the system heat exchangers or radiator type oil coolers are kept free of dirt 6 2 HOSES a Never allow the hydraulic system hoses to remain uncapped or exposed at any time Always cap hoses and fittings immediately when disconnecting any part of the hydraulic system b Make sure all hoses are clean before connecting them to any part of the hydraulic system c Make sure all hoses are clean before connecting them to the drifter d Always use the proper size hoses e Make sure all hose connections are tight and all hoses fittings and adapters are in top notch condition PN NT A LOOSE HOSE CONNECTION NOT ONLY CAUSES LEAKS BUT THE HOSE MAY COME COMPLETEL
26. ica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br
27. ica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H q Bolts Capscrews and nuts Inspect the threads of all bolts capscrews and nuts repair as necessary 6 12 ACCUMULATOR REASSEMBLY a Clamp the accumulator body into a vise b Lightly lubricate each diaphragm and insert them in cavities in the accumulator body NOTICE Be sure the lip on the outside edge of the diaphragm is properly seated in the groove in the accumulator body c Install the accumulator covers using a suitable wrench Torque the covers to 253 Ib ft 343 Nm d Install the seal washers on the accumulator valves Install the accumulator valves on the accumulator covers 6 13 HYDRAULIC ROTATION MOTOR REASSEMBLY Al CAUTION KEEP DIRT ANDOTHER FOREIGN MATERIAL OUT OF THE DRIFTER DIRT IN THE DRIFTER WILL RESULT IN DAMAGE TO THE PISTON AND OTHER INTERNAL COMPONENTS NOTICE Lubricate all seals prior to installation with petroleum jelly Always use new seals when reassembling the motor a Reassemble in reverse order of disassembly unless otherwise noted b Alignment studs are extremely helpful when reassembling the motor They can be shop made to the specifications NOTICE Reassembly involves three steps in the timing of the rotation motor Timing determines the direction of rotation of the motor output shaft and thus the rotation direction of the drill steel
28. m br Instruction Manual MW 80H FUNCTIONS REFER TO THE SECTION OF THE CRAWLER INSTRUCTION BOOK FOR DETAILED INSTRUCTIONS FAILURE TO COMPLY COULD RESULT IN BODILY INJURY b ALWAYS WEAR APPROVED HARD HAT SAFETY SHOES SAFETY GLASSES NOSE MASK AND EAR PROTECTION WHEN NEAR A DRIFTER IN OPERATION c KEEP HANDS ARMS LEGS AND CLOTHING AWAY FROM ALL MOVING PARTS FAILURE TO COMPLY COULD RESULT IN BODILY INJURY d THE DRIFTER STRIKING BAR COUPLINGS DRILL STEELS AND BIT ARE HOT DURING THE DRILLING OPERATION DO NO TOUCH THESE PARTS WITH YOUR BARE HANDS WEAR GLOVES TO PROTECT YOUR HANDS WHEN YOU ARE CHANGING BITS OR STEELS A SEVERE BURN WILL RESULT IF ROTATING PARTS ARE TOUCHED WITH BARE HANDS e KEEP ALL HOSE CONNECTIONS TIGHT A LOOSE HOSE CONNECTION NOT ONLY CAUSES LEAKS AND POOR PERFORMANCE BUT MAY ALSO ALLOW THE HOSE TO COME OFF THE DRIFTER WHIP AROUND AND INJURE THE OPERATOR OR OTHER PEOPLE IN THE AREA f MAKE SURE THAT THE PARTS CLEANING SOLVENT IS NON FLAMMABLE WILL NOT HARM THE SKIN MEETS CURRENT SAFETY AND HEALTH STANDARDS AND IS USED IN WELL VENTILATED AREA g DRY NITROGEN IS THE ONLY GAS PRODUCT TO BE USED TO CHARGE THE DRIFTER ACCUMULATORS NEVER USE OXIGEN TO CHARGE THE ACCUMULATORS IGNITION OF AN OXIGEN AND OIL MIXTURE COULD PRODUCE AN EXPLOSION WHICH COULD SEVERELY INJURE PERSONNEL IN THE AREA h MAKE SURE THE ACCUMULATORS ARE IN GOOD CONDITION MAKE SURE THE ACCUMULATOR COMPONENTS HAVE NO CRACK
29. mance of the equipment it is necessary that the maintenance be made before serious damage occurs It is important to be cautious when performing any service work A general knowledge of the system and or components is important before the removal or disassembly of any components The following is a list of basic precautions that must always be observed a Never attempt major work on the drifter in the field The drifter may be in worse condition after major maintenance was tried in the field than before Send the drifter to the shop b Clean the exterior of the drifter before tearing it down C Use a soft metal plastic or wood hammer for driving the heavier exterior parts d Handle parts carefully Hardened parts might chip or break it drooped on a hard surface 18 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H e Clean disassembled parts in a solvent Probe ports in the backhead housing housing liner drive gear cover etc to loosen and remove foreign matter Place the small parts in a clean container so they will not become lost VA XT WHEN USING ANY SOLVENT TO CLEAN PARTS MAKE SURE THAT IT MEETS CURRENT SAFETY AND HEALTH STANDARDS AND THAT IT IS USED IN AN AREA THAT IT IS USED IN AN AREA THAT IS ADEQUATELY VENTILATED 6 9 DRIFTER DISASSEMBLY a Place the drill guide in a horizontal position b Feed the d
30. mulators must be charged NOTICE An accumulator charging kit is furnished as a standard accessory item with the drilling machine The following DANGER Precautions must be observed when charging the drifter accumulators PN XI DRY NITROGEN IS THE ONLY GAS PRODUCT TO BE USED TO CHARGE THE DRILL ACCUMULATORS NEVER 212 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H USE OXIGEN TO CHARGE THE ACCUMULATORS IGNITION OF AN OXIGEN AND OIL MIXTURE IN THE ACCUMULATOR COULD PRODUCE AN EXPLOSION WHICH COULD SEVERELY INJURE PERSONNEL IN THE AREA MAKE SURE THE ACCUMULATORS ARE IN GOOD CONDITION MAKE SURE THE ACCUMULATOR HOUSING HAS NO CRACKS OR SIGNS OF EXCESSIVE WEAR A DAMAGED ACCUMULATOR COULD RUPTURE AND SEVERELY INJURE PERSONNEL To charge the drifter accumulator proceed as follows a Using a spanner wrench remove the protective caps from the accumulator covers on both accumulators b Loosen the accumulator valve slightly about 1 8 of a turn c Attach the charge valve assembly to the accumulator turning the assembly hand tight d Connect the nitrogen bottle hose to the charge valve assembly charging port e Make sure the discharge valve on the side of the charging valve assembly is closed Turning clockwise closes the valve f Turn the change valve on top of the charging valve assembly counter clockwis
31. odified in any way We shall not in any event be liable for the cost of any special indirect or consequential damage to any one 3 B WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H WOLF Metalurgica The Hydraulic Drifter described in this literature is manufactured by WOLF exacting standards For maximum utilization and efficiency in operating this equipment we urge you to thoroughly read the entire contents of this manual before you begin to drill eds WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H TABLE OF CONTENTS TOPICS Page 1 Introducing this manual 5 2 Abbreviation List o Z o gt Z O 5 3 Safety First 5 3 1 Safety Alert Symbol and Signal Words 6 3 2 Safety Precautions 3 2 Safety Precautions 4 Introduction for Hydraulic DrifterMW 80H n 8 4 2 Specifications gt S O 9 5 Requirements 1 O 10 i 5 10 Connecting the Striking Bar 5 15 Bit Care 5 15 Bit Care S 6 Disassembly Inspection and Assembl 6 1 Hydraulic System O 6 1 Hydraulic System 6 2 Hoses 6 2 Hoses
32. ons before operating or doing any maintenance work on the machine 3 1 Safety Alert Symbol and Signal Words A This is the Safety Alert Symbol When you see this symbol on the machine or in this instruction manual be alert to presence of a hazard All Personnel must understand the DANGER WARNING CAUTION and NOTICE used throughout the next of this instruction manual The DANGER WARNING CAUTION and NOTICE are defined as follows A NNI Danger is used to indicate the presence of a hazard which will cause severe personal injury or death if warning is ignored yN WARNING Warning is used to indicate the presence of a hazard which can cause severe injury or death if warning is ignored CAUTION Caution is used to indicate the presence of a hazard which will or can cause personal injury or property damage if the warning is ignored NOTICE Notice is used to notify people of installation operation or maintenance information which is important but not hazard related By understanding what DANGER WARNING CAUTION and NOTICE mean and using good judgment and common sense all personnel can avoid injuring themselves and or damaging the machine 3 2 Safety Precautions a DO NOT ATTEMPT TO OPERATE THE HYDRAULIC DRIFTER UNLESS YOU ARE THOROUGHLY FAMILIAR WITH ALL THE CRAWLER GAUGES CONTROLS AND epa WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf co
33. rd power stroke thus transmitting the blow energy through the steel to the bit at 2600 blows per minute The hydraulically powered rotation motor is independently controlled and is designed to provide continuous drill steel rotation forward or reverse The motor converts hydraulic fluid to rotation power and transmits the rotation power to the spur gear train housed in the drifter fronthead The hydraulic rotation motor provides smooth powerful rotation especially at low rotation speeds and assures the operator of positive rotation control under all drilling conditions Since hammer action and drill steel rotation are independently controlled the best combination of individual control of both functions can be selected for the most efficient drilling in a particular formation Since the drifter operates on hydraulic fluid power instead of air its operation is unaffected by altitude In addition there is no noise from air exhaust and no fog buildup in working areas The only air requirements for the drifter are for hole cleaning and fronthead lubrication The drifter is equipped with a 34 in 19mm outside diameter blower tube which carries hole cleaning air from the inlet connection in the backhead through the center of the drifter striking bar drill steel and bit to the bottom of the hole without contacting any of the internal parts of the drifter Al CAUTION THE DRIFTER ACCUMULATORS REQUIRE CHECKING EVERY 250 HOURS OF OPERATIO
34. rear faces to the chuck driver for scraping and wear inspect the pawl end of the chuck driver for distortion of the pawl Replace the chuck driver if necessary k Chuck Inspect the pawl end for distortion and wear inspect the condition of the spline in the inside bore Replace the chuck if necessary l Drive Gear Bearings Inspect the drive gear bearings in the gear box If the bearings are worn or damaged use suitable pullers to remove them then press in new bearings m Idler Gear Bearings Inspect the idler gear needle bearings in the idler gear If the bearings are worn or damaged use a suitable fixture to press out the bearings then press in new bearings n Chuck End Bushing Inspect the chuck end bushing for pitted scraped or worn surfaces and replace the bushing if necessary o Striking Bar a The striking face of the striking bar must be square flat and free for all sharp edges The striking bar must be discarded if cracked peened or crowned b The tapered seating face of the striking bar must be free of cracks and sharp edges If the face is peened to 1 16 in 1 59 mm deep or greater the striking bar must be discarded p O rings and Seals Inspect all seals and o rings for nicks cuts tears and deformation and replace as necessary Hydraulic seals and o rings wear during normal operation Hydraulic oil leakage may be an indication that seals or o rings need to be replaced 23 WOLF Metal rg
35. refully and collar hole Once bit is collared in rock full feed pressure may be applied g Always keep sufficient feed pressure on steel system Insufficient feed pressure will cause joints to loosen and threads will be damaged h Always maintain alignment between the drifter and the hole 5 15 BIT CARE For long bit life Drill Steel Care must also be applied to the bit In addition the following steps must also be taken a Never allow the bit to become plugged with loose cuttings Blow the hole continuously b Never force or broach the bit into a hole c Rattle bits from steel using the drifter hammer action with light feed pressure and no rotation Use a Stillson or Bit wrench to remove the bit Never strike the bit with a hammer d Bit carbides should never be allowed to flatten any greater than 1 8 in 3 175 mm between regrinding intervals 15 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H 6 DISASSEMBLY INSPECTION AND ASSEMBLY This section provides information on drifter disassembly inspection of parts assembly instructions and lubricant specifications of the Hydraulic Drifter MW 80A hereafter referred to as drifter The drifter must be included in a definite preventive maintenance schedule to assure top performance and long efficient service life The operating performance is directly depend
36. rifter down the guide until it is in the most accessible position c Disconnect plug and tag the blower air house front end lubrication hose supply and return hydraulic hoses and forward and reverse rotation hydraulic hoses d Install caps on the hose fittings to prevent dirt from entering the drifter e Remove the nuts and bolts which secure the drifter to the mounting plate and use a suitable hoist to lift the drifter off the mounting plate f Take the drifter to a clean work area to disassemble it VA XT THE DRIFTER MUST BE PLACED IN A HORIZONTAL POSITION AND FIXED BY BOLTS ON A WORK BENCH FOR DISASSEMBLY A DRIFTER POSITIONED VERTICALLY COULD FALL AND CAUSE A SEVERE CRUSHING INJURY TO PERSONNEL WHEN USING ANY SOLVENT TO CLEAN PARTS MAKE SURE THAT IT MEETS CURRENT SAFETY AND HEALTH STANDARDS AND THAT IT IS USED IN AN AREA THAT IS ADEQUATELY VENTILATED Loosen and remove the two chuck end bolts and nuts Loosen the four through bolt nuts Loosen the twelve bolts which attach the accumulator assemblies to the cylinder Loosen the backhead gland with an open end wrench Pull out the backhead gland and blow tube in one piece ze e Al CAUTION BE EXTREMELY CAREFUL WHEN REMOVING THE CHUCK END CAP CHUCK AND STRIKING BAR THESE PARTS MAY FALL APART AND CAUSE INJURY TO PERSONNEL k Remove the chuck end cap chuck and striking bar at the same time being careful not to drop any of the parts 19 WOLF
37. that butts up to the cylinder for scratches and gouges repair any irregularities d Cylinder Liner Front Liner Cylinder Back Liner and Cap Liner Inspect the inside diameters of the liners for galling and seizure marks repair any irregularities Replace the liners if necessary e Piston a Inspect the striking face of the piston to see if it is chipped A piston with a chipped striking face must be replaced b Inspect the outside diameter and inside diameter of the piston for galling Any galling requires replacement of the piston f Gear Box Inspect the gear box faces for scratches and gouges repair if necessary g Gear Box Bushing Inspect the gear box bushing for pitted scraped or worn surfaces and replace the bushing if necessary 22 WOLF Metal rgica Tel 55 19 3875 6555 Fax 55 19 3875 5460 e mail info wolf com br site www wolf com br Instruction Manual MW 80H h Drive Gear Inspect the front and rear faces of the drive gear for scraping and wear inspect the drive gear teeth for galling distortion or bending inspect the condition of the spline in the drive gear bore Replace the drive gear if necessary i Idler Gear Inspect the front and rear faces of the idler gear for scraping and wear inspect the idler gear teeth for galling distortion or bending inspect the condition of the idler gear bore Replace the idler gear if necessary Chuck Driver Inspect the front and
Download Pdf Manuals
Related Search