TABLE OF CONTENTS
Contents
1. If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLACE FLICKET MOTOR FLICKER ROD Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly onto the floor Remove the reflector rod from the flicker motor by pulling the end of the rod to the left and separating it from the rubber sleeve Remove the rubber sleeve from the motor shaft Remove the 2 motor mounting screws and remove the flicker motor Discard the old flicker motor Lay the stove on its back with the front window facing upward Remove the bottom heater assembly cover being careful not to damage any of the wiring and lay it on the floor 10 Loosen the flicker motor connections on the terminal block and remove the wires noting their original locations 11 Reassemble in the reverse order TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLA2. 1 position has the same effect as the ON button on the remote control and pressing the switch down 1 position has the same effect as the OFF button of the remote control Pressing the switch up once activates Level 1 twice activates Level 2 and three times activates Level 3 Pressing the switch down turns the electric fireplace OFF Level 1 The flame effect is turned on and the first red indicator light flashes momentarily Level 2 The flame effect remains on the heater is activated to the low heat setting and the first and second red indicator lights flash momentarily Level 3 The flame effect remains on the heater is set to the high heat setting and all three red indicators flash momentarily WIRING DIAGRAM TDS8515 TDS8515 REPLACEMENT PARTS STOVE ELECTRIC 23 PURIFIRE CATALOGUE NO TDS8515 PART NO 69004712 MADE IN CHINA REPLACEMENT PART REPLACEMENT PART NO 1 LOG SET 0438200200RP 2 FOOT 0438210104RP FLICKER MOTOR 2000210200RP HEATER ASSEMBLY 2000230100RP THERMOSTAT 2300150100RP LOWER LIGHT HARNESS 2500280100RP 3 POSITION SWITCH 2800070500RP ON OFF SWITCH 2800070200RP UPPER LIGHT SWITCH 2800070200RP 10 CORD SET 4100040300RP 11 UPPER LIGHT HARNESS 2500150100RP 12 PARTIALLY REFLECTIVE GLASS 5900060600RP 13
3. FLICKER ASSEMBLY 5900080600RP 14 FILTER 0439060100RP 15 TERMINAL BLOCK 4000070100RP 16 KNOB CONTROL 8800000300RP 17 REMOTE CONTROL 3000370600RP 18 REMOTE RECEIVER 3 STAGE Mod 0 C 3000820600 WITH 8501580100RP Mod D 3000820600RP Colour code TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons Light bulbs need to be replaced when you notice a dark section of the flame There are four bulbs under the log set which generate the flames and embers It is a good idea to replace all of the light bulbs at one time if they are close to the end of their rated Group replacement will reduce the number of times you need to open the unit to replace the light bulbs UPPER LIGHT BULB REPLACEMENT Remove the 2 screws at the upper corners of the back panel Lift the back end of the top to clear the brackets and pull back Lift top carefully and place to the side of the stove Caution should be taken as the top mounting brackets may scratch the finish Hold the socket while unscrewing the bulb Hold the socket while screwing in the new bulb Re install the top of the stove LOOSEN TIGHTEN REMOVING AND REPLACING BULB WHILE HOLDING SOCKET LIGHT BULB REQ
4. Control Receiver Page 14 Heater emits an odour Normal operation Normal operation is when the heater emits an odour for a brief period after the heater is initially turned on The heater is burning off any dust accumulated during manufacturing or operation Defective heater assembly Replace heater assembly Loose wiring Trace wiring in unit Heater fan turns on but heater lacks heat Improper operation See Operation Section Defective thermostat Replace thermostat Loose wiring Trace wiring in unit Defective heater assembly Replace heater assembly Heating element is glowing red Normal operation Small glowing sections of the element are considered normal Defective heater assembly If larger glowing sections are causing the heater to trip the thermal cut out unplug unit discontinue use and replace heater assembly TDS8515 TROUBLESHOOTING GUIDE HEATER CONTINUED Problem Cause Solution Service Manual Reference Heater Turns Off after a few minutes of operation but flame stays On Build up of dirt in heater assembly Vacuum Clean Heater Assembly Build up of dirt in Purifire Filter Clean Replace Filter Page 10 Defective Heater Assembly Replace Heater Assembly Page 13 Heater fan runs continuously Loose wiring Trace wiring in unit Page 5 Defective thermostat Replace th
5. REPLACE THE REMOTE CONTROL RECEIVER Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly onto the floor Remove the reflector rod and motor assembly by removing the screws on the front and rear of the heater cover Disconnect the wiring clips and connections from the remote control receiver noting their original locations From inside the fireplace break off the six mounting studs on the receiver by grasping with pliers and twisting on the protruding part of the stud push the remainder of the studs out through the top panel NOTE New mounting studs are supplied with the replacement remote control receiver 7 Properly orient the new receiver and connect all of the wiring connections TDS8515 If the unit that you are replacing the remote control receiver is a MOD 0 C you will have received and updated remote control receiver which has different labelling See below for new locations for the different connections Original Remote Control Receiver 3000431100RP Lire Ir Fror lower and Heater White Sirip From Flame M From Light LL L Updated Remote Control Receiver 3000820600 From Blower and Heater From Flicker Motor and Lights From Flicker Motor and Lights From Blower and Heater Line lr
6. onto the floor Remove the reflector rod and motor assembly by removing the screws on the front and rear of the heater cover Disconnect the wiring clips from the thermostat Remove the 2 thermostat mounting screws and remove the thermostat Connect all of the wiring connections to the new thermostat Reassemble in the reverse order as above TDS8515 TROUBLESHOOTING GUIDE GENERAL Problem Cause Solution Service Manual Reference Circuit breaker trips or fuse blows when unit is turned on Improper circuit current rating Additional appliances may exceed the current rating of the circuit breaker or fuse Plug unit into another outlet or install unit on a dedicated 15 amp circuit Unit turns on or off by itself Remote control has a similar frequency to other remotes in the area Radio frequency disturbance from outside sources Replace remote control initialize to remote control recevier Lights dim in room while the unit is on Unit is drawing close to circuit current rating Move the unit to another outlet or install unit on a dedicated 15 amp circuit Power cord gets warm Normal operation The power cord may get slightly warm to the touch when the heater is on Defective power cord Replace power cord Page 15 APPEARANCE Problem Cause Solution Service Manual Reference Fireplace does not tu
7. required every time there is a loss of power to the remote control in the fireplace l e power failure breaker tripped On Off switch is turned off 1 Ensure that power is supplied through main service panel 2 Locate manual controls refer to FIGURE 3 3 Activate On Off switch position red indicator light 1 will flash Press and hold the 3 position switch for five seconds position UNTIL the second red indictor light flashes Press ON button located on the remote control FIGURE 2 This will synchronize the remote control and receiver B Remote Control Usage The remote control operates the fireplace levels sequentially The level is increased every time the ON button on the transmitter is pressed The fireplace can be turned off at any point by pressing the OFF button on the remote control Level 1 The flame effect is turned on and the first red indicator light is activated Level 2 The flame effect remains on the Purifire is activated and the first and second red indicator lights are activated Level 3 The flame effect and Purifire remain on the heater is activated and all three red indicator lights are activated FIGURE 4 ui Level 1 Indicator 9 Level 2 Indicator ag Level 3 Indicator 3 POSITION SWITCH The 3 position switch operates the electric fireplace in the same manner as the remote control Pressing the switch up
8. unscrewing the bulb Remove the retaining ring from the light socket and remove the assembly out of back of the bracket Cut wires that attach the old light socket to the fire box and strip 12 off of the end of the wires that enter the firebox Mountthe replacement light socket into the bracket and secure with the retaining ring Using the provided wire connectors connect the stripped ends that are connected to the firebox to the ends of the new light socket Reinstall the light bulb Reassembly in the reverse order as above TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons Light bulbs need to be replaced when you notice a dark section of the flame There are four bulbs under the log set which generate the flames and embers It is a good idea to replace all of the light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of times you need to open the unit to replace the light bulbs TO REPLACE ON OFF 3 POSITION AND LIGHT SWITCHES Remove the 2 screws at the upper corners of the back panel Lift the back end of the top to clear the brackets and pull back Lift top carefully and place to the side of the stove Caution s
9. CE THE POWER CORD 1 Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly onto the floor Remove the reflector rod and motor assembly by removing the screws on the front and rear of the heater cover Located and disconnect the power cord wiring connections from the on off switch and the wire connector noting their original locations With needle nose pliers grasp the power cord strain relief grommet from inside the rear panel and push while twisting to remove Pull the power cord out through the hole in the rear cover Install the new cord set through the hole in the rear cover by placing the strain relief over the cord hold the strain relief with pliers and slide into mounting hole 9 Connect all of the wiring connections in their original locations 10 Reassemble in the reverse order as above TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLACE THE THERMOSTAT Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly
10. Leave in this position to maintain the room temperature at this setting For additional heat turn clockwise until you hear the click again and the heater will turn on RESETTING THE TEMPERATURE CUTOFF SWITCH Should the heater overheat an automatic cut out will turn the heater off and it will not come back on without being reset It can be reset by switching the ON OFF SWITCH to OFF and waiting 5 minutes before switching the unit back on CAUTION If you need to continuously reset the heater unplug the unit and call Dimplex technical support at 1 888 DIMPLEX 1 888 346 7539 Extension 4 NOTE The heater may emit a slight harmless odor when first used This odor is a normal condition caused by initial heating of internal heater parts and will not occur again REMOTE CONTROL USAGE This stove is supplied with a radio frequency remote control This remote control has a range of approximately 50 feet 15 25m it does not have to be pointed at the fireplace and can pass through most obstacles including walls It is supplied with one of 243 independent frequencies to prevent interference with other units The frequency code is indicated on the back of the remote control Frequency Code FIGURE 2 Main Power Switch Manual Selection Switch Interior Light Switch FIGURE 3 A Remote Control Initialization This procedure is
11. PARTS AND SERVICE MANUAL FOR DIMPLEX PURIFIRE ELECTRIC STOVE Model TDS8515 X Dimplex 7400050000R04 Table of Contents OPERATION WIRING DIAGRAM REPLACEMENT PARTS UPPER LIGHT BULB REPLACEMENT LOWER LIGHT BULB REPLACEMENT TO REPLACE THE FILTER TO REPLACE THE UPPER LIGHT HARNESS TO REPLACE ON OFF 3 POSITION AND LIGHT SWITCHES TO REPLACE THE HEATER ASSEMBLY TO REPLACE THE REMOTE CONTROL RECEIVER TO REPLACE FLICKET MOTOR FLICKER ROD TO REPLACE THE POWER CORD TO REPLACE THE THERMOSTAT TROUBLESHOOTING GUIDE OPERATION To access the controls go to the back of the stove A ON OFF SWITCH The On Off switch supplies power to all unit functions flame purifire heater B 3 POSITION SWITCH To choose between flame effect setting flame effect with Purifire setting and flame effect with Purifire and heat setting C INTERIOR LIGHT SWITCH The interior light switch supplies power to the interior light D HEATER THERMOSTAT CONTROL To adjust the temperature to your individual requirements turn the thermostat control clockwise all the way to turn on the heater When the room reaches the desired temperature turn the thermostat knob counter clockwise until you hear a click
12. UIREMENTS Quantity of 1 clear chandelier or candelabra bulbs with an E 12 small socket base 15 watt rating TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons Light bulbs need to be replaced when you notice a dark section of the flame There are four bulbs under the log set which generate the flames and embers It is a good idea to replace all of the light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of times you need to open the unit to replace the light bulbs LOWER LIGHT BULB REPLACEMENT Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly onto the floor Remove the burnt out bulbs by pulling straight out of the socket If bulbs are difficult to remove from socket move bulb from side to side while pulling being careful not to damage the light socket Replace lower light bulbs Caution should be taken not to touch the glass portion of the new halogen bulbs Doing so may lead to shorter bulb life Reassemble in the reverse order as above TIGHTEN REMOVING AND REPLACING BULB
13. WHILE HOLDING SOCKET LIGHT BULB REQUIREMENTS Quantity of 3 35 watt Halogen Quartz lamps 120 volt G9 base 9 TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLACE THE FILTER 1 Remove the 2 screws at the upper corners of the back panel 2 Lift the back end of the top to clear the brackets and pull back Lift top carefully and place to the side of the stove Caution should be taken as the top mounting brackets may scratch the finish Remove the old filter and replace with new filter Reassemble in the reverse order as above TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLACE THE UPPER LIGHT HARNESS 1 Remove the 2 screws at the upper corners of the back panel 2 Lift back end of the top to clear the brackets and pull back Lift top carefully and place to the side of the stove Caution should be taken as the top mounting brackets may scratch the finish Hold the socket while
14. e thermostat Page 17 Defective heater assembly Replace heater assembly Page 13 NOISE Problem Cause Solution Service Manual Reference Excessive noise with the heater on Dirty blower assembly Clean blower assembly Defective blower assembly Replace heater assembly Grinding or excessive noise with the heater off Flicker rod hitting or rubbing against internal components Flicker rod replacement Defective flicker motor Replace flicker motor X Dimplex 1367 Industrial Road Cambridge ON Canada N1R 7G8 1 888 346 7539 www dimplex com In keeping with our policy of continuous product improvement we reserve the right to make changes without notice 2012
15. hould be taken as the top mounting brackets may scratch the finish Locate the switch to be replaced Remove the wiring clips and connection noting their original locations Depress the retainer clips on the rear of the switch and push the switch out of the rear of the stove Re install the top of the stove TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO REPLACE THE HEATER ASSEMBLY Gently place stove on its back on a flat surface Remove the thermostat knob Remove the heater cover retaining screws located on the bottom of the stove and lower heater light assembly onto the floor Remove the reflector rod and motor assembly by removing the screws on the front and rear of the heater cover Remove the heater retaining screws form the bottom of the heater cover Disconnect the wiring clips and connections noting their original locations Reassemble in the reverse order as above TDS8515 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons TO
16. rn on Improper operation Refer to User s Guide Defective On Off switch Replace On Off switch Page 12 Defective Remote Control Receiver Replace Remote Control Receiver Page 3 Loose wiring Check wiring connections Page 5 Flame frozen Defective flicker motor Replace flicker motor Page 15 Loose wiring Check wiring connections Page 5 Flame not bright or flame not visible Burnt light bulbs Replace light bulbs Pages 8 9 Loose wiring Check wiring connections Page 5 Defective light harness Replace light harness Log set dim ember bed not glowing Burnt light bulbs Replace light bulbs Pages 8 9 Flame Shudder Defective flicker motor Replace flicker motor Page 15 TDS8515 TROUBLESHOOTING GUIDE HEATER Problem Cause Solution Service Manual Reference Heater is not turning off Defective thermostat Replace thermostat Page 17 Improper operation See Operation Section Page 2 Defective Remote Control Receiver Replace Remote Control Receiver Page 14 Heater is not turning on Defective thermostat Replace thermostat Page 17 Defective heater assembly Replace heater assembly Page 13 Improper operation See Operation Section Page 2 Loose wiring Trace wiring in unit Page 5 Defective Remote Control Receiver Replace Remote
Download Pdf Manuals
Related Search