Home

Mark 1114CW Manual

1. Click OK to close the dialog box Check the values for information which are not essential and then retry reading E041000023 Failed to read the examination file Check the setting information Click OK to close the dialog box Check that the information entered in CSV format is identical with the actual location and name of a folder which includes study orders and retry reading If the folder is mapped as a network drive check the connection status of the folder E041000024 An error occurred during automatic examination file updating Check the setting information Click OK to close the dialog box Check that the information entered in CSV format is identical with the actual location and name of a folder which includes study orders and retry reading If the folder is mapped as a network drive check the connection status of the folder E041000025 Failed to read the examination file Check the setting information Click OK to close the dialog box Check that there is no problem in the media that includes the examination files or whether the file is corrupted or not E041100004 Failed to start up Cxdilnfo Check the setting information Click OK to close the dialog box and inform a service engineer of the error code E050501006 The internal temperature of the detector exceeds the upper limit Images cannot be captured until the temperature has dropped Suspend the examination see
2. Hol iit iai ECE ES cI Image Processing rr a ii M E EXAM gt Examination screen Anatomical Part y Y LUT Edge Enhancement control A Enhancement Edge Frequency control Dynamic Range Adjustment Contrast Boost control Noise Reduction Grid Suppression Sharpness Adjustment KI SIKSI SIK Peripheral Mask Save as Default ImageProc Measurement Annotation Enhancement control 1 Adjust the amount of enhancement Select the Edge Enhancement check box to enable this control and then rotate the scroll wheel on the mouse or click the arrows To increase move the slider to the right To decrease move the slider to the left To disable edge enhancement control mode and cancel the effect Clear the Edge Enhancement check box The on off setting of the Edge Frequency and the Contrast Boost controls see the following steps are subject to that of the Edge Enhancement control 158 7 Other Functions 2 Specify the frequency to be enhanced in the section rendered with higher spatial frequency Rotate the scroll wheel on the mouse or click the arrows of the Edge Frequency control To increase spatial frequency move the slider to the right Applicable for vessel and trabecula imaging To decrease spatial frequency move the slider to the left Applicable for organ and bone imaging 3 Adjust the amount of enhancement applied to the section rendered
3. Deselect the Protect Image check box of the study order in the PAST gt Past List See 3 1 3 Select the transfer failed studies in the Process Viewer and click Delete or Retry refer to 3 3 in the Setup Guide If this error occurs again inform a service engineer of the error code E040E01000 Image analysis processing failed Adjust the image processing parameters manually f the brightness of selected area is not appropriate click ROI to specify the target area See 6 1 6 If the selected area is not cropped appropriately click MEP to specify the target area see 6 1 7 If the masked area is not appropriate click Mask to specify the target area see 6 1 8 E040E01001 Failed to load the extra defect correction file If the problem is not resolved contact a service engineer Click OK to close the dialog box and then calibrate the detector refer to 3 5 1 in the Setup Guide If this error occurs again inform a service engineer of the error code 197 9 Troubleshooting Remedies 198 E041000004 Invalid studies are acquired Check the examination file Check if the study orders are valid Acquire valid study orders again from the HIS RIS database E041000005 Entered information has invalid value Invalid values are replaced with blanks Check the examination file Check if the study orders are valid Acquire valid study orders again from the HIS RIS database E041000006
4. CXDI Control Software NE Canon fl Emergency EXAM gt Worklist screen 3 1 Selecting study orders Worklist tab 3 4 Creating emergency study orders Emergency button deen l Emergency EXAM gt Manual screen 3 3 Creating study orders Manual tab EXAM gt Examination screen Conducting Examinations see chapter 4 40 l Age 24 Years ID P000007 ACUE Vol MADON ADAN POO 1 A 0000007 Hi Chest AP L wise Q T WS CXDI50G VIDIT 3809 AM FOOT Lada Stee i Emergency Start Exa EXAM gt Worklist screen 3 1 2 Checking patient study information in detail 3 1 3 Modifying study information 3 1 4 Changing a workspace 3 1 5 Configuring protocols Edit Exam Study information pane Edit Exam screens EA 3 2 1 Searching for a protocol by a body part 3 2 2 Searching for a protocol by category 41 3 Preparing for Examinations 3 1 Selecting study orders Worklist tab 42 Data exchange and updating services between the HIS RIS database and modalities streamline the examination workflow and maintain steady operation If the Software does not have these services create study orders by manually entering patient study information on the EXAM gt Manual screen see 3 3 Before starting examinations learn the following basic terms used in the Software Study Exam Protocol Workspace A request order for radiographic examination consist
5. A A Heed all warnings and safety information in these instructions and on the product itself Follow all operating instructions Clean the enclosure only with a dry cloth or a vacuum cleaner Clean the DR plate with a damp cloth Use no chemicals or alcohol The detector may be placed in a protective bag to avoid contamination during use IPXO per IEC 60529 Type B per IEC 60601 1 detector is applied part You must allow 10 cm or 4 inches of unobstructed clearance around the unit Do not place the unit on a bed sofa rug or similar surface that could block the ventilation slots If the component is placed in a bookcase or cabinet there must be ventilation of the cabinet to allow proper cooling Keep the component away from radiators heat registers stoves or any other appliance that produces heat Keep the component away from flammable materials The unit must be connected to a power supply only of the type and voltage specified on the side panel of the unit Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent Do not modify the supplied cable in any way Do not attempt to defeat grounding and or polarization provisions Do not use extension cords Do not route the power cord where it will be crushed pinched bent at severe angles exposed to heat or damaged in any way Pay particular attention to the power cord at the plug and where it exits the back of the unit
6. Mark 1114cw User Manual a VCA ANTECH company Table of Contents Mark1114cw User Manual important Safety INTOFMALION ccvssecasccsdenscesanevssceneseneneseyersescsveensses esses eiedsieoeeseveaseess i NOLO rs seiciie Seeseeecuroretavcsceussucsceseivissantesenecaesueninsessunionsvencrerssisetiecieinessseeesste i ALEEN A EPEE N E TE E I T T T E TT TT i GULO saarin EEEE ETE OEE EE TE E EEEE EEES i SDC CIIICALIONS staasas car oE E E EEEE EEE NE iV DEDO aleran A E A iv Guidance and Manufacturer s Declaration for Electromagnetic Compatibility EMC V El ciromagnetic EMISSIONS ssipeuetestcsuederssentictvnetiescanectusteoud si ciedaescisessactesieantueel V Electromagnetic IMMUNItYy eseseececesescececeseccecececoececececoecececeecececescecececeececeoe V Th Mark ACW Systemi srrsssesisssikcccessuarr pinoro ke fen esinen o reida ier cussseaneneessepserseeuss vii The amp Mark TIA CW LADONS caceraeecescncec cscs cine cess rnr i esnan ara reaa viii The Mark 1Tii4cw Features cc cwcsieteccceucrtcexenesisdcddscadianaesocoscnteneecveiantaadisenacecsess IX The Mark 1114cw Important Part Numbers cccccccccccccccccccecccccecccccesccccesccees X The Mark 1114cw Key Connections Overview esesesceseseseececececoecececesoececesesoeo xii Connecting the Generator sesessececesoecececesoecececescececececcecececoececececoececesesoeo xiii Powering Up the Mark 1114cw System esesessesecesoecececesoececese
7. Name Study Status_ SN James Smith Mary Johnson Robert Williams 3 15 2012 2 01 58 PM 0000003 0000004 0000005 0000006 0000008 0000009 0000010 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM P000003 P0000004 P000005 P0000006 P000008 P000009 P000010 Patricia Jones John Brown Paul Davis Susan Wilson Nancy Moore Refresh Option Michael Taylor Rebind Study Information dialog box 3 Select the target study order to be rebound Select a study order in the Study Information list To refresh or narrow down the study information Click Refresh If necessary change the narrowing conditions using Refresh Option in advance For details on operation see step 1 in 3 1 1 I aeaee 87 4 Conducting Examinations 4 Bind the study information with the suspended study order Click OK and then click OK in the Confirm study information to bind dialog box that appears Confirm study information to bind OK to bind data Patricia Jones DoB 6 12 1997 14 Years Click to return to step 3 P0000004 Female Ca le To conduct examinations using the rebound study information Proceed to step 1 in 4 1 4 2 or 4 3 88 4 Conducting Examinations 4 8 Binding study information with the images of an emergency study See also 3 4 for details on emergency studies
8. Ul Workspace Sort Unselect Edit Exam Study information pane 4 4 Recapturing images 4 5 Rejecting images EXAM gt Examination screen after capturing an image Before Chest AP X wise Replace Protocol amp Series Image Information Replace Protocol amp Select Workspace dialog box dialog box 4 2 Replacing an 4 3 Reprocessing an image of a incomplete protocol complete protocol with another protocol 4 9 Adding information to a complete protocol 69 4 Conducting Examinations 4 1 Conducting radiographic examinations Before starting examinations learn the following basic terms used in the Software Exposure mode Mode enabled for every single exposure categorized by the images created in that mode Two modes are available and images created in each mode are as follows Radiography Radiographic images Stitch Combined images Exposure type Type of protocols categorized by the available exposure mode Two types are available Radiography Radiography mode Stitch Stitch mode DX Digital X ray protocol A generic name for protocols for which the exposure type is Radiography or Stitch see chapter 8 Examples of appearance of incomplete protocols and their features by exposure type ia Chest AP L wise Q il Radiography type USNS A ready preview thumbnail is displayed to the left of the protocol name Stitch type Captures two to four radiographic images and combines them to form
9. The power cord should be unplugged from the wall outlet if the unit is to be left unused for a long period of time Immediately stop using the component and have it inspected and or serviced by a qualified service agency if The power supply cord or plug has been damaged Objects have fallen or liquid has been spilled into the unit The unit has been exposed to rain The unit shows signs of improper operation The unit has been dropped or damaged in any way Place the unit on a fixed level surface strong enough to support its weight Do not place it on a moveable cart that could tip over Do not place on the floor or in an area where the system may be exposed to liquid Page ii Important Safety Information Caution continued Sound Eklin System will become unresponsive when exposed to Electrostatic Discharge ESD or Electrical Fast Transient EFT conditions This is the normal response to these environmental conditions Please restart the system to return to normal operation Do not install detector close to strong electromagnetic fields or devices which may interfere with wireless communication see detector service manual for details USB ports are for keyboard and mouse only User is responsible for evaluating the system with any devices connected to this port for compliance to IEC 60601 1 1 Ethernet port is not to be used during acquisition User is responsible for evaluating the system with any devices
10. 162 ae TA GID DEGEEODED This control is available only in level 3 mode Se Image Processing Anatomical Part Enhancement Dynamic Range Adjustment Noise Reduction PiSKiKT KI lt KT lt Grid Suppression Grid Name Grid Name selector 180cm_12 1 40 Al Grid Suppression option Save as Default ImageProc Measurement Annotation Grid Suppression control Enable grid line suppression mode Select the Grid Suppression check box Grid Name selector When the grid in use is different from the one specified for the current protocol select the name of the grid in use from the drop down list Also refer to 3 4 1 in the Setup Guide for details on the Protocol Workspace Settings option To disable grid line suppression mode and cancel the effect Clear the Grid Suppression check box Some details of the image may be restored 7 Other Functions 7 2 8 Adjusting the image sharpness Sharpness Adjustment control This control is available only in level 3 This control increases the sharpness of an entire image for an effective diagnosis iasa Ry Li D ees 2 2 hal 4 Ge de LE e a EA KA ve E j MOICIREE J Image Processing PF a ag ia EXAM gt Examination screen Anatomical Part UT Enhancement Dynamic Range Adjustment Noise Reduction Grid Suppression me BS RS Be Se
11. 5 2 2 Conducting additional examinations using a complete study Using exclusively complete studies that are saved in the image capture computer users can restart studies without creating a new study order 1 Select the target study See steps 1 and 2 in 5 2 1 for details on operation 2 Move the study to the Study List in the EXAM gt Worklist screen Click Restart Exam and click OK in the confirmation dialog box that appears The study disappears from the Study List in the PAST gt Past List screen The current study status will be changed to Restart and the study will appear in the Worklist OK to continue Cancel Ce O K Click to return to step 1 m na ey _ _ Restart Exam PAST gt Past List screen NOTE Restart Exam is also available in the PAST gt View screen 101 5 Reviewing Images 3 Start examination In the EXAM gt Worklist screen select the restarted study with the Restarted indication in the Study Status column add new protocols See 3 1 5 and then click Start Exam For details on conducting examinations see chapter 4 Study Status hana si ee dining Selected restarted DEOR MIos ADLA PR PO an kohne study EEEE ENF yf 20 Aesults H Emergency Start Exam EXAM gt Worklist screen NOTE Only the images captured with the newly added protocols can be transferred to destination storages and printers NOTE Only panning see
12. DICOM StorageCommitment failed Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide Or resend the image from the PAST gt View or PAST gt Past List screen See 7 1 5 If this error occurs again inform a service engineer of the error code E040507007 DICOM StorageCommitment failed If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide Or resend the image from the PAST gt View or PAST gt Past List screen See 7 1 5 If this error occurs again inform a service engineer of the error code E040600008 Failed to access the target disk Check the disk drive and retry from the Process Viewer Check that the destination storage disk or device is functioning normally Then retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide If this error occurs again inform a service engineer of the error code E040600009 The process was interrupted as there was not enough free disk space Replace the disk with a new one and retry from the Process Viewer If recording is in progress wait until the process is completed and replace the disk Replace the current disk with one containing sufficient free space T
13. E F G H Measure distance button 6 3 1 page 129 Measure Cobb angle button gt 6 3 3 page 132 Measure height difference button 6 3 4 page 134 Measure angle button gt 6 3 2 page 131 Delete 76 3 page 129 Show hide object selector 6 3 page 129 Show hide scale selector 6 3 page 129 Correction of Magnification option 6 3 1 page 129 1 4 11 Annotation panel Annotation calcification s postopera ImageProc Measurement Annotation A Add Edit 76 4 1 page 136 B Enlarge Reduce Delete 76 4 1 page 136 24 1 4 12 Stitch Screen amim g O U gt Image view pane gt 8 3 1 page 175 Toolbar 8 3 1 page 175 Image overview pane 8 2 page 168 Auto 78 3 1 page 175 Arrow buttons 8 3 1 page 175 Edge Enhancement control 8 3 1 page 175 1 Getting Started 25 1 Getting Started 26 2 Starting and Shutting Down the Software 2 1 Starting the Software 2 2 Shutting down the Software 2 3 Conducting offline examinations 2 4 Utilizing peripheral devices This chapter explains how to start and shut down the Software Shutdown Confirmation Dialog Box m Transter All Data Overview E Backup Database Latest backup date time 3 21 2012 12 42 PM Shutdown User Adrersrtistuar Spinn Seiteg Gatomice Dspiry sssistion Commton Canon Restart Options Cancel CXDI Control Software NE EXAM gt Wo
14. E040100008 An invalid detector has been specified Check the setting information If the problem is not resolved contact a service engineer Click OK to close the dialog box and retry the previous operation If this error occurs again inform a service engineer of the error code E040100023 Generator communication failed Enable the generator connection with Connect GEN on the system setup screen Restart the system if the generator connection has failed Click OK to close the dialog box and then click Connect GEN refer to 2 1 1 in the Setup Guide If the generator cannot be connected restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code 188 9 Troubleshooting Remedies E040100053 The detector issued an error Try again If the problem is not resolved contact a service engineer When using a wireless detector show Additional Information to check the Error Code number detector error code to be shown and then click OK to close the dialog box Refer to the Troubleshooting in the User s Manual of the Digital Radiography and check the operation corresponding to the Error Code number Perform the operation and retry the examination If this error occurs again inform a service engineer of the error code When using a detector other than wireless detector click OK to close the dialog box and retry the previou
15. Monochrome Light Refer to 2 3 1 in the Setup Guide for details on setting the screen background color In this manual the Cool Light screen that is the default setting is used for explanation 1 Getting Started Example 1 2 3 Mouse wheel operations The mouse pointer may change to As while pointing on a list table at a numeric entry field or on a control slider In such cases rotating the mouse wheel scrolls through the list enters values or moves the slider For a control slider dragging the slider is an alternative operation 1 2 4 Touch screen display operations This manual assumes that users are using a mouse and keyboard However touch screen displays are also available Unless otherwise stated the operating procedures using a touch screen display is the same as those using a mouse and keyboard When using a touch screen display Click OK is equivalent to Touch OK 1 2 5 References References to this manual Associated information in this manual is indicated by the section number or by the section number followed by the title as seen below See 3 1 5 See step 2 in 3 1 5 for details on operation Proceed to 3 1 5 Configuring protocols References to other documents Associated information in other manuals is indicated by the manual title or the section number followed by the manual title as seen below Refer to the Operation Guide supplied with the power box For details r
16. NOTE If Cancel is clicked the following dialog box appears Note that the image being transferred will be deleted if Yes is clicked in the following dialog box i S Confirmation Are you sure to cancel transfer When an image is deleted a corrupted image icon appears on the protocol s thumbnail and a dialog box that prompt the user to retry image transfer appears Pateni MAVRO p oF rarnana Taria ravien MAREA ARENT Epu aruy iue aio ae mAg Corrupted image icon Error Details Error Code E020201007 Date 2 21 2012 Time 2 36 PM Category ERROR Description A detector communication error occurred Please retake this protocol If the problem is not resolved contact a service engineer 4 Conducting Examinations 76 5 Continue the examination If any incomplete protocols remain repeat steps 2 through 4 Before replacing the detector during the examination S Unselect to disengage the Ready status of the protocol Confirm that the ot Ready indicator appears in the system status bar and then replace the EET To resume the Ready status click on an incomplete protocol To review captured images during examinations Proceed to 5 Reviewing Images To perform post processing Proceed to 6 Post Processing Images To transfer captured images to PACS before finishing examination Click Send to Storage to transfer all captured images to the designated PACS After t
17. NOTE Only study information included in a study order which were listed in the EXAM gt Worklist screen can be added moved to a suspended study order s dose not appear for a study order which are manually created 7 Select a suspended study order in the EXAM gt Worklist screen Click to highlight a study order for which Pending is displayed in the Study Status column Patient and study information of the selected study order appears in the study information pane NOTE If two or more study orders are selected using the multi selection feature click unwanted study orders to clear them and leave only one target study order highlighted On Line Off Line selector indicator le ox rebind i Study Status Suspended study oo A f l Teta Arruit Arr Arki Theory 20 Artis Start Exam EXAM gt Worklist screen 86 4 Conducting Examinations 2 Show the Rebind Study Information dialog box Click H NOTE In offline mode f is disabled In such cases click Off Line to enable online mode NOTE Ifthe Controller is disconnected from the MWL server is disabled In such cases enable connection in the Connection gt MWL tab refer to 2 6 3 in the Setup Guide Study Information list Rebind Study Information Study Information A Accession No 0000001 0000002 Study DateTime Patient ID 3 15 2012 2 01 58 PM 3 15 2012 2 01 58 PM P000001 P0000002
18. PAST _ gt View screen s sssssnsnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn na 21 WA elel e gN AAE A E E A N A E E E E suaauuavaeudacnecades 22 14 9 Imag PROCESSING panels irira Ea Ea EA eaa 23 1 4210 Measurement pane lonneiseoi a Ea 24 TATANO ON DANG lran a wuxbe 24 1412 SUUCI SCTE O haia 25 2 Starting and Shutting Down the Software 2 1 Starting the SOM WANES asiusnsinisanaa aaa raaa 30 2 2 Shutting down the Software sssnssnsnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmn 32 2 3 Conducting offline EXAMINATIONS cc ccenseensensenseensessenseenseaseessonsesseessensenees 36 2 4 Utilizing peripheral devices cccesceseesensceeesenseneesensenscssesensensesensensessesensensenensenses 3 Contents 3 Preparing for Examinations 3 1 Selecting study orders Worklist tab ccsccsecescsnscnsenseensensenseonsensensenssenseneens 42 3 1 1 Acquiring study orders from the HIS RIS database c ccssecesecescenscessensensennsensennseeneeees 42 3 1 2 Checking patient study information in etal c ccesecescensenseceseenscnsecesenseensensenneeeseenenaes 46 3 k3 Modifying study INFOFMATION sisina AA ain 47 3 1 4 Changing a workspace sssssssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen nnnm mnnn 49 3 L5 Conigu ring Protocols sasini A a AA aa NA 51 3 2 DCICCUNG DFOLOGOIS aisinas a a 53 3 2 1 Searching for a pro
19. Specified ID is not found in the examination file Check the examination file Check if the study orders are valid Acquire valid study orders again from the HIS RIS database E041000008 An error was discovered while checking the user input by the script If the problem is not resolved contact a service engineer Click OK to close the dialog box and inform a service engineer of the error code E041000010 E041000012 An error has occurred in CCRHIS library Try again If the problem is not resolved contact a service engineer Show Additional Information to check the error details and click OK to close the dialog box Then retry the previous operation according to the error details If this error occurs again inform a service engineer of the error code E041000020 Examination file loading was halted because the acquired exams reached the maximum number End the suspended exam and retry reading Click OK to close the dialog box Restart suspended studies from the EXAM gt Worklist screen See 4 6 finish the examinations and then retry reading 9 Troubleshooting Remedies E041000021 Invalid studies are loaded and cannot be displayed Check the examination file Click OK to close the dialog box Check the values for essential information and then retry reading E041000022 Entered information has invalid value Invalid values are replaced with blanks Check the examination file
20. Third party software will be installed on the image capture computer when the control software is being installed by the service engineer For details on the third party software and its license agreements consult your service engineer Safety Summary Before using this product read this safety summary thoroughly This information will prevent the users and persons involved from sustaining physical harm and or property damage Read the separate Setup Guide and the Digital Radiography CXDI series User s Manual as well Safety Notices The following safety notices are used to emphasize certain safety instructions This manual uses the caution symbol along with a caution message CAUTION This notice is used to identify conditions under which improper use of the product may cause minor personal injury This notice is used to identify conditions under which improper use of the product may cause property damage CAUTION Safety Precautions Follow these safeguards and properly use the application software to prevent injury and damage to any equipment data While preparing for examinations e Be sure to confirm that the entered information patient name ID number birth date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient e Be sure to use the Emergency button only for an emergency examination If not heeded the resulting pat
21. annotations Preview thumbnail Preview annotations refer to 2 5 1 in the Setup Guide End Exam EXAM gt Examination screen 96 5 Reviewing Images To overview images in the current Exam multi view mode Click EJ Up to nine images for the current Exam appear in the image view pane at a time To resume single view mode double click an image in multi view mode or click E EJ multi view The selected view mode button is highlighted onL IMM Mage view pane End Exam To perform post processing Proceed to 6 Post Processing Images To restart examinations after review Click an incomplete protocol and continue the examination see step 2 in 4 1 97 5 Reviewing Images 5 2 Reviewing images on the PAST gt View screen Images previously captured and saved in the directory in the image capture computer storage media and other storage can be reviewed In particular studies saved in the image capture computer can be restarted for additional examinations or copied for further image processing 7 Show the PAST gt Past List screen Click the PAST tab and then click the Past List tab To sort the listed studies Click a sort item in the column header The current order is indicated by ascending or Fj descending in the column To switch between ascending and descending sort order click the same item again To arrange the order of the column headers Drag an item and
22. 10 page 24 76 3 page 129 Annotation 1 4 11 page 24 6 4 page 136 End Exam 4 1 page 70 Send to Storage 74 1 page 70 Suspend Exam 4 6 page 85 19 1 Getting Started 1 4 6 PAST gt Past List screen HDD free space icon 3 1 1 page 43 Search For Study List pane 73 1 1 page 42 Study List 75 2 page 98 Patient information pane 3 3 2 page 62 Study information pane 1 4 2 page 15 5 2 page 98 Restart Exam 5 2 2 page 101 Recall Copied Exam 5 2 3 page 102 Recall Exam 5 2 1 page 100 rQOmmMOoOOD WwW R 20 1 Getting Started 1 4 7 PAST gt View screen rQaQimmamoqgodw gt View mode buttons 5 1 page 96 Info 75 1 page 96 Toolbar 71 4 8 page 22 76 1 page 112 Image view pane 5 2 page 98 Output setting button 77 1 page 142 Patient information pane 3 3 2 page 62 Study information pane 1 4 2 page 15 5 2 page 98 Restart Exam 5 2 2 page 101 Save Image s 75 2 1 page 100 Back To List 75 2 1 page 100 21 1 Getting Started 22 1 4 8 Toolbar I O TMO O U gt Zz Z T AS Rotation Flip buttons gt 6 1 1 page 114 Negative positive button 6 1 2 page 114 Panning button 6 1 3 page 115 HQ 6 1 4 page 116 Zoom in out buttons 76 1 4 page 116 Fit button 76 1 4 page 116 L R 76 1 5 page 117 ROI 76 1 6 page 118 Crop butto
23. 110v Power Outlet NEMA 5 15 Cord Sound Eklin Page xiv The Mark 1114cw CXDI Control Software NE Anatomical Fart T brhemiemerl 3S ynsk Range Adprin Y Mater Redkertaoe Grii Tipp Sharpe Adjustment T Patphaa Maik ram Image Preoeving 1 T brhemiimert 3S Dyn k Range Adjie Y Nai Redhettine Grid sapprraon Sharpe Adjustment To Pepher Maik s l eeu pen Sound Eklin Page 1 To the Customers Thank you for purchasing the Canon CXDI Control Software NE hereinafter called this product Operating instructions are divided into two volumes the Operation Manual and the Setup Guide Before using this product be sure to read these manuals thoroughly in order to utilize this product more effectively Disclaimer 1 Inno event shall Canon be liable for any damage or loss arising from fire earthquake any action by a third party or other accidents any intentional or negligent action by the users any trial usage or other usage under abnormal conditions 2 Inno event will Canon be liable for direct or indirect consequential damage arising out of the use or unavailability of this product Canon will not be liable for loss of image data due to any reason 3 In no event shall Canon be liable for personal physical harm or property damage that is sustained when the instructions are not followed or the product is misused 4 Itis the responsibility of the attending physicians
24. 4 6 and wait until the temperature decreases Then restart the suspended study order 199 9 Troubleshooting Remedies E050501008 E050501009 A drive circuit error occurred Contact a service engineer E05050100A E05050100B An abnormality was detected in the detector structure Contact a service engineer E05050100C E05050100D A control line connection error was detected in the detector Contact a service engineer Inform a service engineer of the error code E050501010 Failed to transfer the image data Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry the image transfer If this error occurs again inform a service engineer of the error code E050501012 An abnormality was detected in the analog power supply for the detector Contact a service engineer E050501014 A grid error was detected Contact a service engineer E050501016 The firmware is different Contact a service engineer Inform a service engineer of the error code E050502026 A detector communication error occurred The cable may be disconnected or there may be power discontinuity in the detector Check that the cable is correctly connected and restart the detector If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box check the cable connection to the detector and restart the detector If this
25. 6 1 3 and zoom in out See 6 1 4 operations can be enabled for images that are carried over from the restarted study 5 2 3 Creating images using different image processing parameters of a copied study Using exclusively complete studies that are saved in the image capture computer users Can post process images included in those studies and can transfer the images to destination storages and printers The copied studies can also be restarted 7 Select the target study See steps 1 and 2 in 5 2 1 for details on operation 102 5 Reviewing Images 2 Review the copied study Click Recall Copied Exam and click OK in the confirmation dialog box that appears The copied study appears in the PAST gt View screen 5 Confirmation The selected studies will be copied and recalled OK to OK 7 continue E i Click to return to step 1 G p Is PAST gt Past List screen Back To List PAST gt View screen copied study To perform post processing Proceed to 6 Post Processing Images To transfer the post processed image Proceed to 7 1 Printing and transferring images To restart the copied study For details on operation see steps 2 and 3 in 5 2 2 To review other images Click Back To List or the Past List tab and then follow steps 2 and 3 in 5 2 1 103 5 Reviewing Images NOTE When the copied study is listed in the PAST gt Past List screen i
26. 8 kV air Mains power quality should be that of a typical commercial or hospital environment 2 kV for power supply lines Electrical Fast Transient Burst 2 kV for power supply lines IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 11 Power Frequency 50 60 Hz Magnetic Field IEC 61000 4 8 1 kV for input output lines 1kV differential mode 2 kV common mode lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 dip in UT for 5 seconds 1 kV for input output lines 1kV differential mode 2 kV common mode lt 5 UT gt 95 dip in UT for 0 5 cycle 40 UT 60 dip in UT for 5 cycles 70 UT 30 dip in UT for 25 cycles lt 5 UT gt 95 dip in UT for 5 seconds Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the CDXI 80C Wireless requires continued operation during power mains interruptions it is recommended that the CDXI 80C Wireless be powered from an uninterruptible power supply or a battery Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment Note UT
27. AVIV Click to switch to body part search Start Exam mode Edit Exam screen category search mode To select a category tab If necessary click A or v to scroll tabs and then click a target category tab 56 3 Preparing for Examinations To select a protocol list using the category list Click Category List and then click a target category in the list Category List a exam Workist Z Click to close the category list Start Exam 2 Select a target protocol Click a target protocol in the protocol list The selected protocol appears at the bottom of the study information pane 5 3 Preparing for Examinations 3 3 Creating study orders Manual tab 58 Additional study orders can be created using the Software in radiology rooms and the created studies as well as those acquired from the HIS RIS database will be conducted 3 3 1 Registering patient study information Rr i Patient Lis E E CQ lirih Hama Column head Patient list Delete Es EXAM gt Manual screen The EXAM gt Manual screen appears when the user is logged in to the Software that does not have data exchange and updating services with the HIS RIS database If the EXAM gt Manual screen does not appear The EXAM gt Worklist screen may appear instead of the EXAM gt Manual screen In such a case click the EXAM gt Manual tab Be sure to confirm that the entered information
28. Embedding laterality markers IN iMageS ssnssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnna 6 1 6 Adjusting the overall brightness on the ROI basis cesscsesccesseensecnsecenseenseensenenseoaes 6 17 Gropp lNG IMAGES aiie a E E A a AE OE 6 1 8 Maskin the p nripneral arawit a a e aaa 6 2 Using the Image Processing panel Level 1 csscesscsscnsensecssnsenseessensenes 6 2 1 Adjusting the brightness of bright region and dark region ssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 6 2 2 Adjusting the overall brightness and contraSt ssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 6 3 Using the Measurement panel 1 ccccssceseeseesensseseesensseseesensensensensensensensensensenees 6 3 1 Measuring the distance between two specific points ccsceceeeeneceensensensensensenensensensenes 6 3 2 Measuring the angle Of a specific part cceesceeceesenseeseeeeensenseeseeseessoasensesensenssonsonsenseneens 6 3 3 Measuring the Cobb anglen naaa aa a a aa aaa 6 3 4 Measuring the height difference s sssnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn 6 4 Using the Annotation panel ssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnnn 6 4 1 Creating editing custom annotations sssssssnussnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnnn 7 Other Functions 7 1 Printing and transferring IMAGES s
29. RS Sharpness Adjustment Effect control Y Peripheral Mask Save as Default ImageProc Measurement Annotation Sharpness Adjustment control 1 Adjust the sharpness of the image Select the Effect check box and then rotate the scroll wheel on the mouse or click the arrows To increase sharpness move the slider to the right To disable sharpness adjustment control mode and cancel the effect Clear the Effect check box 163 7 Other Functions 7 2 9 Masking the area outside of the irradiation field Peripheral Mask control This control is available only in level 3 mode The setting of this option will be the default for the current protocol and will be applied to images in the EXAM gt Examination screen immediately after every exposure Mask in the toolbar can temporarily switch the setting as well See 6 1 8 Ci ___ ia eS ie cs le my 3 E D p S a al gt Anatomical Part Examination screen Cc Enhancement Dynamic Range Adjustment Noise Reduction Grid Suppression BSS BSS SS BSS Se Sharpness Adjustment A Peripheral Mask CE Mask option i gt Save as Default ImageProc Measurement Annotation Peripheral Mask control 1 Enable the mask processing Select the Mask check box To disable peripheral mask processing Clear the Mask check box NOTE Even if this setting is changed after exposure t
30. Reject 84 Before retake 83 Rejection Reason 83 Reset 112 Retake 83 Review EXAM gt Examination screen 96 PAST gt View screen 98 REX 157 REX control 156 RIS Pending indications 85 Study order 42 ROI 118 Rotate 114 205 Index S Save as Default 155 Save to System 143 151 152 Search for Study List 44 99 Select Workspace 50 Send 76 Series Image Information 91 Sex 59 Shutdown 34 Single view mode 96 Stitch screen 173 175 180 Stitch type protocol 168 Storage commitment 99 Study deletion 106 Study information Binding 89 Checking 46 Modifying 47 63 Pane 15 Rebinding 86 Registering 58 Study list 42 Study order 42 Acquiring 42 Creating 58 64 Deleting 61 Modifying 51 Multi selection 45 Selecting 45 Sorting 43 98 Suspend Exam 85 System status bar 71 Wireless detector 72 T Tab 10 Toolbar 22 112 Touch screen 11 V View mode 96 W Warning 182 List 201 Wireless detector 50 72 Worklist Screen 42 Tab 10 Workspace 42 Change 78 206 Z Zoom in Zoom out 116 Csound eklin gt a VCA ANTECH company Sound Eklin Technical Support 6359 Paseo Del Lago Carlsbad California 92011 USA toll free phone fax international 800 268 5354 option 3 760 918 9626 76 918 9620 1 760 918 9626 www soundeklin com 2013 All Rights Reserved Sound Eklin a VCA ANTECH company
31. When an emergency study is ended with End Exam the following dialog box appears Data binding options Study Information Accession No Study DateTime Patient ID Name Study Status AN 0000001 3 15 2012 2 01 58 PM POOOO001 James Smith 2A 3 15 2012 2 01 58 PM P0000002 Mary Johnson Free ADO Space poe ilf 7 a 3 15 2012 2 01 58 PM P000003 Robert Williams EXAM gt Examination screen 0000004 3 15 2012 2 01 58 PM P0000004 Patricia Jones 000101010 3 15 2012 2 01 58 PM P000005 John Brown 0000006 3 15 2012 2 01 58 PM P0000006 Paul Davis Refres h F Refres hO pti O n 2 15 9012 7 N1 5Q DAA DANNANNR Sucan iileana Click to cancel the operation OK NOTE When the data exchange and updating services with the HIS RIS database are not provided with the Software EXAM gt Manual screen appears instead of the dialog box above 1 Select a data binding option Confirm the Add study information option is selected To bind the information later Select the Do not add study information yet option and then click OK to suspend the examination Later restart the suspended emergency study see 4 6 for details click End Exam to show the above dialog box and then select the Add study information option to bind the information l oee 89 4 Conducting Examinations Not to bind the information Select the Not add study information option and then click OK Be sure to confirm that the entered informati
32. a single long length image Stitch 2images Q WS CXDI50G Be sure to confirm that the entered information patient name ID number birth N caution date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient 70 4 Conducting Examinations 7 Start an examination Click Start Exam NOTE If Start Exam does not work even if a study is selected click Edit Exam and add the protocol to the study order Protocol name Workspace name a System status bar Patient posture oa EAA CE A detector setup A Start Exam Detector name Grid attachment status Status Waiting Ready Not Ready Capturing Click to show and hide preview annotations Workspace Sort Study Sort Unselect Click to configure protocols see 3 1 5 Preview annotations 71 4 Conducting Examinations 12 NOTE NOTE A battery indicator and a signal strength indicator are shown on the system status bar during an examination using a wireless detector For the wireless detector refer to the Digital Radiography CXDI series User s Manual Example of the system status bar indication while using a wireless detector Ready Simm ome l Battery indicator Signal strength indicator i 60 100 charge Til Strong f 959 Mil Medium f 5 8 H Poor No signal f 4 or less Ye 9 Whe
33. amp Add to List Click to cancel the operation and close the Place only 5 tA dialog box 136 6 Post Processing Images Select a preset custom annotation or input a new annotation Select a preset custom annotation from the custom annotation list in the Annotation panel To input a new annotation click Add Edit in the Annotation panel to show the Add Edit Annotation dialog box type an annotation in the text box and then click Place only The selected custom annotation or a new annotation highlighted with a dashed orange border appears at the preset position on the image view pane To add the new annotation to the custom annotation list If the newly input annotation is expected to be frequently used click Place amp Add to List instead of Place only NOTE Custom annotations can also be created on the system setup screen For details refer to 2 5 2 in the Setup Guide NOTE Amaximum of 100 annotations can be registered in the custom annotation list If the target annotation cannot be found in the list click the scroll arrows to navigate the list To modify a preset custom annotation In the Add Edit Annotation dialog box select a preset custom annotation from the custom annotation list to put the text in the text box and then modify the text When using a modified annotation temporarily click Place only When both the original and modified annotations must be saved in the list click Place amp Add
34. and transferring images see 7 1 Screen tabs Examination PACS server Orage media Creating study orders Manual tab see 3 3 Captured image transfer 12 13 1 Getting Started 1 4 Part names of screens Quick reference 14 NOTE Screen details may differ depending on the settings of the Software 1 4 1 EXAM gt Worklist screen I 0O mnmMmMOOo O U gt HDD free space icon gt 3 1 1 page 43 System setup button 2 1 1 in the Setup Guide Search For Study List pane 3 1 1 page 42 Study List 73 1 1 page 42 Data transfer indicator 4 1 page 70 On Line Off Line selector indicator 2 3 page 36 Patient information pane 3 1 2 page 46 Study information pane 1 4 2 page 15 73 1 2 page 46 Start Exam 74 1 page 70 Emergency 3 4 page 64 1 Getting Started 1 4 2 Study information pane and protocols A c ij Chest AP X wise o B i wsnos Ul Chest AP L wise WS CXDI50G i p D A Study title Accession number 73 1 2 page 46 gt Study Information Display in 2 4 1 in the Setup Guide Protocol list 4Chapter 4 page 67 Information button 3 1 2 page 46 73 1 3 page 47 Thumbnail Edit Exam 73 1 5 page 51 mM O DW 15 1 Getting Started 1 4 3 Edit Exam screen ExXAM PAST a earch te ptor Sto by Wiorkpouscr Body part search mode Body part selector 3 2 1 page
35. control To increase move the slider to the right To decrease move the slider to the left NOTE The Edge Enhancement effect on the Stitch Screen is temporal and it is not saved 4 Save the changes to the image Click OK to close the Stitch Screen NOTE When Cancel is clicked to close the Stitch Screen images cannot be stitched 178 8 Stitching images Long length imaging 8 3 2 Modifying long length images in the PAST gt View screen Partial images for an already stitched long length image can be aligned again on the Stitch Screen to create a new image 7 Show a long length image See 5 2 for details on operation Recall Exam gt a pan LA gt ae soe A ae H TT E r e PAST gt Past List screen P T L PatieghiD POOoO 10 ie P eeina Michael Taylor Pate Name Michael ayer j Exposure Thine E DoB LAL Ae 01 Years ay Tui ar rerl I POLO i L 000010 Tehe 3 Click to save changes for the long length image Click to return to the PAST gt Past List screen AH PAST gt View screen 179 8 Stitching images Long length imaging 2 Modify the target long length image on the Stitch Screen Click Stitch in the target protocol For details on operations on the screen see 8 3 1 Click to close the Stitch Screen without saving changes for the long length image OK When two or more complet
36. drop it in the target position Dragging the column border also adjusts the width of the column NOTE The items displayed in the column head can be selected in the system setup screen For details refer to 2 4 1 in the Setup Guide NOTE The directory options are displayed when external storage is specified on the Disk Storage tab refer to 2 6 5 in the Setup Guide If the directory options do not appear it means that all of the listed studies are stored in the image capture computer PAST EXAM Past List tab f wren Fat Shuwfy List MEI bea OG Mak Siara A Ji m EEE oaee peo Name ttm prine nesan Sore Rena J Column headers SWRI es Graj JAN nd Restart Exam The selected study S EEEE highlighted pipe xz Recall Copied coooa 214012 DOLE AM Po0000 Mary fohncon S E 13967 Exam i lie J Recall Exam Ee Ses i oN PAST gt Past List screen example of the Local DB selected for the directory option 98 5 Reviewing Images Image transfer results can be confirmed In the Study List complete studies are listed with indications of image transfer results to the destination printer or data storage The indications in the transfer result Store Result Print Result column are as follows Done Sending J Error and Hl no setup For details on image transfer see 7 1 The storage commitment results R4 Committed Committing Ey Commitment error or J no
37. fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the CXDI 80C Wireless is used exceeds the applicable RF compliance level above the CXDI 80C Wireless should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the CXDI 80C Wireless b Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m Sound Eklin Page vi The Mark 1114cw System The Mark 1114cw system links seamlessly with the X ray generator to provide the best image quality in a small lightweight self contained system The Mark 1114cw portable Acquisition Stations are intended to be used by Veterinarians for intermittent mobile diagnostic applications They will connect the Mark 1114cw Device to a CXDI Canon 80C Wireless Digital X ray Detector Sound Eklin Page vii The Mark 1114cw System continued The Mark 1114cw Labels Sound Eklin Windows License Key is located on bottom of Electronics Box PES CR REDRESS a 8a as aie lt Mark 1114cw Electronics Box Serial number Mark
38. images of an emergency study after finishing the examination 65 3 Preparing for Examinations 66 Conducting Examinations 4 1 Conducting radiographic examinations 4 2 Replacing an incomplete protocol with another protocol 4 3 Reprocessing an image of a complete protocol 4 4 Recapturing images 4 5 Rejecting images 4 6 Suspending an examination 4 7 Rebinding other study information with that of the suspended study order 4 8 Binding study information with the images of an emergency study 4 9 Adding information to a complete protocol This chapter explains how to conduct examinations and how to reprocess retake or reject images Furthermore data binding feature to associate study information with the images of emergency study is explained Workflow EXAM gt Worklist screen Preparing for Examinations see chapter 3 4 7 Rebinding other study information with that of the suspended study order il e Cancel EXAM gt Examination screen before capturing an image 4 1 Conducting radiographic examinations 4 6 Suspending an examination Image arrangement screen Arranging and printing images automatically see 7 1 2 Rebind Study Information dialog box only for emergency studies 4 8 Binding study information with the images of an emergency study EXAM gt Examination screen Reviewing Images see chapter 5 Post Processing Images see chapter 6 68 A 0000001 ee soose
39. in the column To switch between ascending and descending sort order click the same item again To arrange the order of the column headers Drag an item and drop it in the target position Dragging the column border also adjusts the width of the column 2 Set the information Click Set gt The Edit Exam screen appears and a new study order that contains no study information is created in the study information pane NOTE Insufficient entry of ID and items marked with an in step 1 disables Set refer to 2 4 1 in the Setup Guide for details on the setting of essential information items l Continued 59 3 Preparing for Examinations 3 Show the Edit Study Information dialog box Click on the newly created study order and then click Edit Edit Study Information ACTH Edit Exam screen Retermng Physician Study Descrip Newly created study order Reading Physician institution Mame Delete Add Study See To protect the stored images in 3 1 3 for details Click to cancel the operation 4 Enter study information for the newly registered selected patient Select preset descriptions from the drop down lists or enter descriptions for the following information boxes select or clear the Protect Image option if necessary and then click OK ACC The accession number is automatically given to each study order at the point of issue Referr
40. in the selected study order Frequently used protocols list Body part selector Recently used protocols list Examination history list AVIV Coe Delete Click to cancel the operation Edit Exam screen body part search mode aeaee 51 3 Preparing for Examinations 2 Configure protocols To include an additional protocol in the study order Click a target protocol in a preferred protocol list The selected protocol appears at the bottom of the protocol list in the study information pane To specify an insertion point click to highlight a protocol in the study information pane before clicking the additional target protocol The additional protocol is inserted just below the highlighted protocol NOTE In body part search mode up to three types of protocol lists Frequently used protocols Recently used protocols and Examination history are available for protocol selection For details on list operation see 3 2 and on list configuration refer to Protocol Settings in 2 4 1 in the Setup Guide In addition category search mode is also available see 3 2 2 NOTE The Recently used protocols list and Frequently used protocols list cannot be shrunk at the same time To delete a protocol Click a target protocol in the study information pane and then click Delete To arrange the order of protocols Click to highlight a target protocol in the study information pane and then click A or v Note that
41. installed and put in to service according to the EMC information provided in this manual Portable and mobile RF communication equipment can affect the Mark 1114cw system The use of accessories transducers and cables other than those specified by Sound Eklin may result in increased EMISSIONS or decreased IMMUNITY of the EQUIPMENT The accessories defined on page xi define the approved components for this system The cable lengths are considered to be the maximum length for acceptable EMMISSIONS and IMMUNITY The Mark 1114cw should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary the EQUIPMENT should be observed to verify normal operation in the configuration in which it will be used There are no user serviceable parts inside There are no preventative maintenance requirements Refer all servicing to qualified service personnel To avoid risk of electric shock this equipment must be connected to a supply mains with protective earth To reduce the risk of fire or electric shock do not expose the unit to moisture or water Do not allow foreign objects to get into the enclosure If the unit is exposed to moisture or a foreign object gets into the enclosure immediately disconnect the power cord from the wall Take the unit to a qualified service person for inspection and necessary repairs Page i Important Safety Information continued Caution Sound Eklin
42. panel Levels 2 and 3 The following selectors and controls available in levels 2 and 3 mode select and adjust imaging parameters for advanced image processing NOTE In general users do not need to use controls in level 3 mode If the Image Processing panel does not appear Click ImageProc To hide the panel click it again 7 2 1 Switching access levels om Show hide selector for histogram and LUT curve see 6 2 1 p Y ak F E Access level selector indicator l Anatomical Part Examination screen LUT Enhancement Dynamic Range Adjustment Click to shrink and expand Noise Reduction the parameter controls rid Suppression Sharpness Adjustment LKI SISISIKIKSIKSIKS Peripheral Mask Save as Default I mageProc Measurement Annotation If the Authorization dialog box appears To perform restricted image processing enter a user name with image processing privilege and password and then click OK For the image processing privilege refer to 2 2 in the Setup Guide Enter level 2 mode Click 2 of the access level selector indicator 2 Enter level 3 mode Click 3 of the access level selector indicator NOTE To enter level 3 mode from level 1 mode click 2 first and then click 3 of the access level selector indicator 154 7 Other Functions To save changes in the parameter settings for the current protocol Click Save as Default in level 3 mode In addition t
43. patient name ID number birth date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient To delete patient information in Recent Patient List Click unused patient information to highlight click Delete and then click OK in the confirmation dialog box 3 Preparing for Examinations 7 Enter patient information Patient information Set gt Taro Canon 2 z 20 7 1982 Age 30 Years P000101 Sex Male Female Other Click to clear the patient information entry Enter any of the following information in the text boxes and select an option for the Sex of the patient Name Patient name DoB Age Birth date of a patient Age will be automatically calculated based on this entry Age of a patient ID Patient ID When the target patient information already exists Patient information previously created in the EXAM gt Manual screen appears in the Recent Patient List pane In such a case click the target patient information on the list instead of performing step 1 above For more efficient selection it is advisable to narrow down the information on the list Information entry in step 1 above also narrows the selection To sort the order of the listed patient information Click a sort item in the column header The current order is indicated by ascending or E descending
44. the Contrast control To increase move the slider to the right To decrease move the slider to the left NOTE Fine adjust the contrast in a range of 10 to 10 relative to the Base Contrast value The supported adjustment range depends on the Base Contrast value In some cases the range may be narrower than 10 to 10 For details on Base Contrast control see 7 2 3 128 6 Post Processing Images 6 3 Using the Measurement panel When reviewing images measurement objects such as line angle objects values and units are Superimposed over the images on the image view pane and these objects are embedded in the image data to be transferred to a storage server printer or other destination directories To enable measurement mode Click Measurement 6 3 1 Measuring the distance between two specific points exam PAST a mm Worklist Manual lt i Examination O KWF Gino James Smith TE a macl z pi a l Measured distance 4 j A n Accmasicnn P eo J n Wask Acgulsi on Time AAE tia Al ies M ated Obst Ret isy a 7 1 sa r Click to show and 50 space hide all line angle EXAM gt Examination screen perane objects 4 g es Es Click to show and Delete i hide the scale at S i E R ESAE Correct the bottom of the SOD 1414 2 mm SID 1000_ mm image view pane ImageProc Measurement Annotation Correction of Magnification Measurement NOTE
45. the Software is used in a mobile system the Software can operate without connection to the HIS RIS database In such cases follow the steps below 7 Disconnect from the network Click On Line Clicking the button toggles between On Line and Off Line To resume connection Click Off Line a E a On Line Off Line Hame Coon Coons aa eet OO aes Ooo I7 HE AR PS Aaa ae ane 00000 NOTE Switching to online mode again transfers the images captured during offline mode to the PACS server storage device and printer and also exchanges the study history with the HIS RIS database 36 2 Starting and Shutting Down the Software 2 4 Utilizing peripheral devices The Software supports the use of a bar code reader and a magnetic card reader For details on these devices refer to the operation manuals supplied with these devices 3 2 Starting and Shutting Down the Software 38 3 Preparing for Examinations 3 1 Selecting study orders Worklist tab 3 2 Selecting protocols 3 3 Creating study orders Manual tab 3 4 Creating emergency study orders Emergency button This chapter explains how to prepare for examinations and how to check patient and study information before capturing images It is also possible to modify study information details if necessary See 3 1 for details Workflow Start screen Starting the Software see 2 1
46. the dialog box Select the halted transfer task and then click Retry on the process viewer to retry the task refer to 3 3 in the Setup Guide If the above remedy does not work try to reconfigure the Storage tab settings refer to 2 6 1 in the Setup Guide and manually try to transfer the image starting on the PAST gt View screen See 7 1 5 E040501016 Data communication between the hospital network was interrupted during file transmission Check the setting information Click OK to close the dialog box After confirming that the destination server and the network are functioning normally retry the operation If this error occurs again inform a service engineer of the error code E040501017 The CXDI system read an unsupported DICOMDIR file Check the target disk and retry reading Use a disk that was made using the Software E040501018 A transmission error occurred Try again If the problem is not resolved contact a service engineer Retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide Or resend the image from the PAST gt Past List screen See 7 1 5 If this error occurs again inform a service engineer of the error code E040502002 040502004 E04050200D 04050200F E040502010 040502014 Association negotiation failed There may be a problem in the settings of the system or that of the other communication party Check the setting information E04050201B 04050201F
47. the image sharpness Sharpness Adjustment Control cesesssessseeneeeeenees 7 2 9 Masking the area outside of the irradiation field Peripheral Mask control 05 Contents 8 Stitching images Long length imaging 8 1 What is long length imaging sccesseescenscessenseenssenscossenseonseonseensonseensensenseens 168 8 2 Capturing and stitching IMAGES cccescenscenseeseenscnseensenssenseonseessenssonseasenseens 168 8 3 Realigning modifying and stitching partial IMAGES csseseseeseneeseesenseneees 175 8 3 1 Aligning partial iMageS sssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnna 175 8 3 2 Modifying long length images in the PAST gt View SCreen csssssesscenseenseenseeenseenes 179 9 Troubleshooting Remedies 9 1 Confirming details of the Problem cccccessceseeeseenscensenssenseensensenssenseoesenseees 182 SF Fd Io ats 1c 1 8 or a a y o imme mer ete a nemar eA nmr Arve Seen Penmaes 183 9I N2 Error ST a a a Ea e a a 186 9 1 3 Warning St iscan aaO a aaa aa ea aa aaO an aaa aa AaRON ania Kepada kanina 201 MOGA risinn 204 Contents Getting Started 1 1 Introduction 1 2 Notations 1 3 Workflow diagram for a general radiographic examination 1 4 Part names of screens Quick reference 1 Getting Started 1 1 Introduction The CXDI Control Software NE hereinafter referred to as the Software is designed to provid
48. the ruler is corrected based on the SOD and SID values minor errors may occur caused by the margins and other output settings of the printer 4 Print the arranged images Click OK NOTE Ifa dialog box indicating Arrange all images on the Image List appeared drag all images to the arrangement preview pane and click OK For details on automatic image selection for printing the Selected exposure mode to be printed automatically option refer to step 5 under 2 6 2 in the Setup Guide 147 7 Other Functions Example of automatic arrangement Layout templates are automatically selected according to the size and captured sequence of images image 1 image 2 image 3 image 4 a 5 image 6 image 7 Images in the selected study processed in order of protocols ee ee ee ee CEE ee ee m Layout templates page 1 page 2 page 3 page 4 148 7 Other Functions 7 1 3 Arranging and printing images manually It is possible to create printouts of specified images arranged side by side on film sheets 7 Finish an examination Click Edit Exam in the EXAM gt Examination screen All images to be printed in the current Exam are arranged in the arrangement preview pane Enable image arrangement mode NO Click Delete All Page in the image arrangement screen All images in the current Exam appear in the Image List 3 Create a page and select a target layout template Click Add Page click on a
49. to close the dialog box and then retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide If the problem cannot be resolved contact the system administrator The problem may be resolved by checking the DICOM conformance statement If this error occurs again inform a service engineer of the error code E040506001 The transmission was interrupted as the CXDI system received a FAILURE status from the destination DICOM printer Check the DICOM printer Check the DICOM printer For details of Printer Status refer to Annex C 13 9 1 in the DICOM standard Part3 Information Object Definitions or the DICOM conformance statement E040507001 DICOM StorageCommitment failed Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide Or resend the image from the PAST gt View or PAST gt Past List screen See 7 1 5 If this error occurs again inform a service engineer of the error code E040507002 040507005 DICOM StorageCommitment failed If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry sending the image from the PAST gt View or PAST gt Past List screen See 7 1 5 If this error occurs again inform a service engineer of the error code 195 9 Troubleshooting Remedies E040507006
50. to provide medical care services Canon will not be liable for the faulty diagnosis 5 Roentgenography image processing image reading and image data storage must be performed in accordance with the laws of the country or region in which the product is being used The user is responsible for maintaining the privacy of image data 6 Information in this manual may change without prior notice 7 Screen images in this manual may differ from those displayed on your image capture computer due to customization updates and improvements in the software 8 We ve taken all possible means to ensure the content accuracy of this manual If you have any questions or problems contact your sales representative or local Canon dealer Trademarks e The Canon name and Canon logo are registered trademarks of Canon Inc e Ethernet is a trademark of Xerox Corporation e Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries or regions e TrueType is a registered trademark of Apple Inc e Intel and Intel Core are trademarks of Intel Corporation in the U S and other countries e Other systems and product names in this manual are the trademarks of the manufacturers that have developed them Copyright e All rights reserved e Under copyright laws this manual may not be reproduced in whole or in part without the written permission of Canon Third Party Software
51. until the zooming is reset 116 6 Post Processing Images To resume default magnification and display position Click ED 6 1 5 Embedding laterality markers in images In general laterality markers can automatically be embedded in an image during an examination by presetting protocols This section explains manual embedding procedures after an examination Though these markers generally indicate DICOM laterality they can also be used to simply indicate left and right of the image refer to Protocol Settings in 3 4 1 in the Setup Guide Annotations other than L and R can also be embedded see 6 4 1 Embed a laterality marker in an image Click L or R The L or R mark appears at the preset position For details on the position settings refer to Protocol Settings under 3 4 1 in the Setup Guide To change the position of an embedded laterality marker Click a laterality marker to show its boundaries in orange and then click a destination point on the image view pane The marker appears at the click point 117 6 Post Processing Images Laterality marker j d 6 1 6 Adjusting the overall brightness on the ROI basis Use this function if details in dark or bright regions are missing in an image even though brightness was automatically adjusted by the Software The brightness of the overall image can be adjusted based on the mean brightness of an ROI 1 Enable overall bright
52. with lower spatial frequency Rotate the scroll wheel on the mouse or click the arrows of the Contrast Boost control To increase move the slider to the right Applicable for trunk imaging To decrease move the slider to the left Applicable for extremity and cephalic imaging 7 2 5 Expanding or narrowing the dynamic range Dynamic Range Adjustment control This control is available only in level 2 and 3 modes and it is necessary that Auto mode is selected for the LUT control M s Image Processing PF mari Wa 3 EXAM gt Examination screen Anatomical Part Enhancement la im Range Adjustment Dark Region control Bright Region control Noise Reduction Grid Suppression Sharpness Adjustment KIKI KIK Peripheral Mask Save as Default ImageProc Measurement Annotation Dynamic Range Adjustment control 159 7 Other Functions 1 Adjust the dynamic range in the dark region Select the Dark Region check box to enable this control and then rotate the scroll wheel on the mouse or click the arrows To narrow move the slider to the right To expand move the slider to the left NOTE When adjusting images where negative positive inversion is applied the operation directions of the Dark Region control are reversed The same goes for step 2 To disable dark region control mode and cancel the effect Clear the Dark Region check box 2 Adjust the dynamic range in the bright regi
53. 1114cw A frame Serial Number CE Markings and Manufacture Date a KE 2 6359 Paseo Del Lago sound eklin Carlsbad CA 92011 amp 760 918 9626 ONG an Sound Eklin K UL60601 1 CAN CSA C22 2 No z J E Lh ames YS 601 1 soundeklin com MODEL MARK 1114cw EN60601 1 INPUT POWER 120 VAC 5 6A 60Hz EN60601 1 4 SERIAL Made in usa MONTH or whys KS ZLA on Pe PANY a B1 Page viii The Mark 1114cw System continued The Mark 1114cw Features Power Button with LED Light Hard Drive Activity Indicator Sound Eklin Page ix The Mark 1114cw System continued The Mark 1114cw Important Part Numbers 94 859 Mark 1114cw 34 851 Mark 70 80C 34 852 Mark Electronics Assembly A Frame Assembly v2 Sound Eklin Page x The Mark 1114cw System The Mark 1114cw Important Part Numbers continued r 10 867 Min X Ray se H 10 137 Battery 25 Sync Cable for i charger for Canon Mark 1114cw Wireless Series Syncs the generator s prep and expose cycle with the computer 90 403 10 10 135 Extra Ethernet Battery Pack for Patch Cable Canon Wireless Connects the computer to the network to allow for easy image transfers from the Mark 1114cw to PACS 10 171 Equine 20 IEC NEMA Power Extension Cord Connects the 94 124 CXDI 80C Canon Wireless Detector includes two Mark 1114cw to any batteries Standard U S 110V Captur
54. 53 Search by Category 73 2 2 page 56 Frequently used protocols list 73 2 1 page 53 Recently used protocols list 73 2 1 page 53 Study information pane 1 4 2 page 15 3 1 2 page 46 Start Exam 74 1 page 70 OQmmoeOoO U D Examination history list 73 1 5 page 51 16 Start Exam Category search mode H Category tabs 3 2 2 page 56 I Search by Body Part 73 2 2 page 56 J Protocol list 73 2 2 page 56 K Category List 73 2 2 page 56 1 Getting Started 17 1 Getting Started 1 4 4 EXAM gt Manual screen Patient information entry 73 3 1 page 58 Recent Patient List 73 3 1 page 58 Delete 3 3 1 page 58 Emergency 73 4 page 64 Start Exam 74 1 page 70 A B C D E 18 1 Getting Started 1 4 5 EXAM gt Examination screen A B C D E I 7 PAST F p Manual G p amp j Ls T sls y J K L M N O P View mode buttons gt 5 1 page 96 Info 75 1 page 96 Toolbar 71 4 8 page 22 76 1 page 112 Image view pane 4 1 page 70 Retake 74 4 page 83 Reject 74 5 page 84 System status bar 4 1 page 70 Output setting button 7 1 page 142 Patient information pane 3 1 2 page 46 Study information pane 1 4 2 page 15 74 1 page 70 Image Processing panel 71 4 9 page 23 6 2 page 126 ImageProc 6 2 page 126 7 2 page 154 Measurement 1 4
55. E040502020 Association was stopped There may be a problem in the settings of the system or that of the other communication party Check the setting information 192 9 Troubleshooting Remedies E040502021 E040502023 E040502058 Association negotiation failed There may be a problem in the settings of the system or that of the other communication party Check the setting information Click OK to close the dialog box and check the properties of Host Name Port or Called AE Title in the Connection tab screens refer to 2 6 in the Setup Guide Check that destination server and the network are functioning normally If the problem cannot be resolved contact the system administrator The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E040505001 E040505002 E040505004 040505009 E04050500B 040505014 An error occurred in DICOM communication Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box Click Refresh to acquire the study orders see 3 1 1 The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E040505015 A response error occurred in DICOM communication Check the destination modality or server etc Click OK to close
56. Processing 1 End Exam To disable the masking effect and exit mask edit mode Click so that the highlighting is cleared and then click OK The masked area will not be displayed but the area itself will be saved NOTE Changes made to the on off setting of the masking effect do not affect the state of the Mask check box see 7 2 9 125 6 Post Processing Images 6 2 Using the Image Processing panel Level 1 126 6 2 1 When reviewing images fine adjustment of the brightness and contrast is available using the Image Processing panel NOTE Depending on the image the adjustable range of the following image processing parameters may be restricted In such cases the preview image may not change even if the sliders are moved past a certain point Imaging parameter adjustment restrictions Most of the advanced imaging parameters are preset when the Software is installed and their access privileges are classified into two levels 2 and 3 These levels may be restricted to administrative users The advanced parameters for level 2 and 3 modes are explained in 7 2 1 Switching access levels If the Image Processing panel does not appear Click ImageProc To hide the panel click it again Adjusting the brightness of bright region and dark region These parameters are available for all access levels However at all level modes adjustments are not needed for normal use since appropriate pre processing is applied to th
57. Protocol configuration of Exams can be modified in the EXAM gt Examination screen using Edit Exam as described in 3 1 5 Even after starting an examination if incomplete protocols remain they can be replaced with other protocols easily Furthermore the protocol s workspace can also be changed 7 Show the Replace Protocol amp Select Workspace dialog box Click to highlight the target incomplete protocol and click it again The selected protocol name appears in the Before box Q highlighted screen Protocol list ee Tore CoD Before box When replacing the protol select the tanget protocol iram preboced irsya iva Abdomin AP K aro A ODES Select Workspace list Click to cancel the ae Wl operation Em 0K A J Replace Protocol amp Select Workspace dialog box To simply change the workspace Select the target workspace in the Select Workspace list and then click OK 78 4 Conducting Examinations 2 Select the replacement protocol Replace Protocol amp Select Workspace dialog box Click the replacement protocol in the protocol list The selected protocol name appears in the After box Ci After box CXDIS0OG m CXDI55G gt r Select Workspace list gt lt i CXDI4OEC SZ CXDI40GC WS CXDI60G y M C CXDI60G Z N Click to cancel the operation OK Cance To change the workspace for the replac
58. The measurement unit and the scale shown at the bottom of the image view pane can be selected on the system setup screen For details refer to 2 4 1 in the Setup Guide 129 6 Post Processing Images 130 1 SOD box Enable distance mode Click RA NOTE Once distance mode is enabled operations other than step 2 below are disabled Be sure to complete operations through step 2 Measure the distance between two specific points Click two points on the image view pane A line object indicating the measured distance between the points appears Perform other distance measurements Repeat steps 1 and 2 To change the position and length of a line object Click on the line object so that handles appear on both ends of the object Drag the middle of the object to move or drag either handle to lengthen or shorten the line object To delete a line object Click on the line object so that handles appear on both ends of the object and then click Delete To correct the measured values and the scale The measured values can be corrected using the magnification ratio based on the SOD source object distance and SID source image distance values The values preset for the protocol refer to 3 4 1 in the Setup Guide or executed values received from the X ray generator are displayed in the SOD and SID boxes in the Correction of Magnification option The scale displayed at the bottom of the image view pane also changes M
59. ails on manual alignment see 8 3 1 To stitch images after the examination is suspended Select the target suspended study from the EXAM gt Worklist screen or EXAM gt Pending List screen if HIS RIS interoperability services are not used and then click Start Exam Click the target stitch type protocol in the EXAM gt Examination screen and then click Stitch For details see 8 3 1 173 8 Stitching images Long length imaging 8 Continue the examination Click OK in the Stitch Screen The EXAM gt Examination screen returns and a stitched image preview thumbnail appears in the protocol If any incomplete protocols remain repeat steps 3 through 7 HE TE Ewi Ia Michael Taylor MUTE ime l 1 Dof Dob MISIE 64 Years ID POGOO10 To post process long length images For details see 6 Post Processing Images See also 6 3 3 for the Cobb angle measurement and 6 3 4 for the height difference measurement 9 Finish the examination Click End Exam The image data will be transferred to a preset destination such as a printer refer to 2 6 in the Setup Guide 174 8 Stitching images Long length imaging 8 3 Realigning modifying and stitching partial images The following procedures are performed in the dedicated Stitch Screen after both partial images are captured and they are stitched 8 3 1 Aligning partial images When the last partial image is captured the Stitch Sc
60. ar all Click to close the Search Options panel conditions in the Search Options panel Search Options panel 54 3 Preparing for Examinations To clear the detailed conditions Click the highlighted button again 3 Select a target protocol If a target protocol appears in a protocol list Click the target protocol in the protocol list The selected protocol appears at the bottom of the study information pane If a target protocol does not appear in a protocol list Select by Workspace option Select the Select by Workspace option and click the protocol to show the Select by Workspace dialog box select the target protocol and then select the target workspace The selected protocol with the desired workspace appears at the bottom of the study information pane Select by Workspace option exam na Only the protocol ee names appear exam eas Woki Z hina AP Select by Workspace dialog box Click to cancel workspace selection and return to the arch by Start Exam previous screen 595 3 Preparing for Examinations 3 2 2 Searching for a protocol by category NOTE PrePack protocols refer to 3 4 3 in the Setup Guide can be selected only in category search mode 7 Enable category search mode Click Search by Category in body part search mode Search by Category Edit Exam screen body part search mode Category tabs poernre 3 O Protocol list
61. ce between two specific points 6 3 2 Measuring the angle of a specific part 6 3 3 Measuring the Cobb angle 6 3 4 Measuring the height difference Annotation 6 1 1 Rotating flipping images 6 1 2 Inverting a negative image to a positive image and vice versa 6 1 3 Panning images 6 1 4 Zooming images 6 1 5 Embedding laterality markers in images 6 1 6 Adjusting the overall brightness on the ROI basis 6 1 7 Cropping images 6 1 8 Masking the peripheral area 6 4 1 Creating editing custom annotations 111 6 Post Processing Images 6 1 Using the toolbar Basic processing j T i EXAM gt Examination screen 112 When reviewing images the following buttons are available Rotation clockwise counterclockwise buttons see 6 1 1 Flip vertical horizontal buttons see 6 1 1 Inversion negative positive button see 6 1 2 Panning button see 6 1 3 HQ Zooming zoom in zoom out fit buttons see 6 1 4 L R see 6 1 5 ROI see 6 1 6 Crop button see 6 1 7 Mask See 6 1 8 Reset Toolbar To undo the previous operation Click cy Note that some operations such as panning cannot be undone To restore the default processing settings of the current protocol Click Reset All modifications made for the current image are canceled 6 Post Processing Images To switch the toolbar If Tool 1 or Tool 2 appears at the bottom of the toolbar
62. connected to this port for compliance to IEC60601 1 1 This system is not intended for use in an oxygen rich environment Page iii Specifications Operation Environment 15 C to 35 C 30 to 75 RH 70 to 106kPa pressure Storage Transport 10 C to 55 C 15 to 80 RH 70 to 106kPa pressure Power Requirements 100 240 VAC 5 6A 50 60Hz Weight net 47 lbs CAUTION Applicable for USA Canada or where approved for the usage Caution To prevent electric shock match wide blade of plug to wide slot Insert fully Risk of electric shock Do not open Caution To reduce the risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel This symbol is to alert the user to important operating and maintenance service instructions in this manual and literature accompanying the product This symbol is to alert the user to the presence of uninsulated dangerous voltages inside the product s enclosure that may constitute a risk of electric shock Disposal The customer is responsible for the disposal of the medical device Disposal activities must follow the regulations especially controlled industrial waste of the country where the device is used Sound Eklin Page iv Guidance and Manufacturer s Declaration for Electromagnetic Compatibility EMC Electromagnetic Emissions The CDXI 80C Wireless is intended for use in the electro
63. ctor firmware may have been updated after registration of the detector Register the detector again Inform a service engineer of the error code Click OK to close the dialog box and then shut down the image capture computer see 2 2 183 9 Troubleshooting Remedies FOSO20FFFF An internal error occurred Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code FO40100066 The IP addresses for the wireless and wired configurations have been reversed Contact a service engineer Click OK to close the dialog box and inform a service engineer of the error code FO040300048 The control software controller is not compatible with the current detector firmware Update the control software controller firmware FO040300049 The detector firmware may have been updated after registration of the detector Register the detector again FO40300050 The Jumbo packet settings are incorrect or a network card not compatible with Jumbo packet is used Contact a service engineer Inform a service engineer of the error code Click OK to close the dialog box and then shut down the image capture computer see 2 2 FO40300051 The IP addresses for the wireless and wired configurations have been reve
64. d changing the image transfer settings Before finishing examinations users can check and change the destination directories and printers Show the Output Settings dialog box Click EM To enable the preset printer for printing images Select the Print Output option When users need to check the image arrangement before printing select the Show the image arrangement screen before printing option To disable the printer clear the Print Output option To enable the preset storage servers PACS or a storage media for image transfer Select a storage server name or storage media name option under the Storage or Disk Storage option To disable the storage server or storage media clear the option To save the changes made in the Output Settings dialog box Click Save to System The changes will be reflected in the default setting that can be configured in the Connection tab in the system setup screen and also applied to subsequent printing and transfer operations Apply the changes and close the dialog box Click Apply to apply changes to the current study NOTE The changes are cleared after the study is ended and its image printing transfer is complete or suspended and then the default settings resume 143 7 Other Functions 7 1 2 Arranging and printing images automatically The Software can be configured to start printing automatically after finishing an examination by clicking End Exam Furthermore depending
65. dentical to those of the original protocol are displayed in the protocol list For details on searching for a protocol see 3 1 5 and 3 2 Before Chest AP X wise After After box Replace Protocol amp Series Image Information a _ Series Image Series Information Image Information Information dialog Series Description box Operator Name cxdiUser Body Part ABDOMEN Click to cancel the operation 3 Set the replacement protocol Click OK aeaee 81 4 Conducting Examinations To perform reprocessing using incomplete protocols already listed in the study information pane Drag the preview thumbnail of the original complete protocol and drop it on the target incomplete protocol and then click OK in the warning dialog box that appears The original complete protocol changes to an incomplete protocol Preview thumbnail of the complete protocol E 4 s a i E L ee EL be O SSS a eS 3 L__ j c Chest AP L wi o E f i WS CXDISOG ll a ga iL Abdomen AP X wise Q Il Abdomen AP X wise wi a WwS CXDI50G O WS CXDI50G EXAM gt Examination Incomplete protocol used for Preview thumbnail after screen reprocessing reprocessing 82 4 Conducting Examinations 4 4 Recapturing images lf a captured image is not acceptable further examination using the same protocol is required In such cases follow the procedure below 7 Se
66. e REX Mode for tone curve adjustment to change brightness of the region of examination based on X ray dose When the REX option is selected Click the REX control text box and type a value and can be used for the value specification The higher the value the brighter the image The lower the value the darker the image 3 Adjust the Base Brightness Rotate the scroll wheel on the mouse or click the arrows of the Base Brightness control To increase move the slider to the right To decrease move the slider to the left NOTE These adjustments are not available when the REX option is selected for Brightness Adjustment mode see 7 2 3 NOTE When adjusting images where negative positive inversion is applied the moving directions of the Base Brightness control are reversed 4 Adjust the Base Contrast Rotate the scroll wheel on the mouse or click the arrows of the Base Contrast control To increase move the slider to the right To decrease move the slider to the left NOTE The value of Base Brightness and Base Contrast are used as a reference value for the Brightness control and Contrast control See 6 2 2 157 7 Other Functions 7 2 4 Enhancing contrast for anatomical part shape definition Enhancement control This control is available only in level 2 and 3 modes and it is necessary that Auto mode is selected for the LUT control EE tet any CI ig a ae ns 3 n Ta ia E jeje ca ES
67. e dialog box Button Error type FATAL see 9 1 1 ERROR see 9 1 2 EE WARG see 9 1 3 9 Troubleshooting Remedies 9 1 1 Fatal error list FO30100005 Required COM servers are not installed Contact a service engineer Inform a service engineer of the error code Click OK to close the dialog box and then shut down the image capture computer see 2 2 FO3020200E Memory allocation failed Restart the system If the problem is not resolved after restarting contact a service engineer FO03020201B Failed to upload calibration data Restart the system If the problem is not resolved after restarting contact a service engineer FO3020201C Failed to transfer the image data Restart the system If the problem is not resolved after restarting contact a service engineer FO3020201F A detector error occurred Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software See 2 2 If this error occurs again inform a service engineer of the error code FO030202021 The control software controller is not compatible with the current detector firmware Update the control software controller firmware FO030202022 The Jumbo packet settings are incorrect or a network card not compatible with Jumbo packet is used Contact a service engineer FO30202023 The dete
68. e a steady and efficient workflow in the field of digital radiography when linked to an RIS HIS network Up to four CXDI detectors including wireless detectors can be connected simultaneously to the Software Images captured using the CXDI detector are automatically processed by the Software to achieve diagnostic image quality Furthermore the Software offers advanced processing features with intuitive operability 1 2 Notations 1 2 1 Screen names In this manual screens are identified by the titles of active tabs For example EXAM gt Worklist screen indicates that the EXAM and Worklist tabs are selected in sequence 3 HDD LJ IZA Manual J Active tabs 1 2 2 Buttons 10 In this manual the key top labels of buttons on the Software screen are written in square brackets such as OK and Cancel or the icon is shown Button appearance on the Software screen Enabled buttons Appear with a navy blue background A Enabled buttons prompted Appear with a navy blue background surrounded by a blinking line Disabled buttons Appear with a grayed out key top label B Selected buttons Appear highlighted in pale blue surrounded by a white line C Toggle buttons Key top label and color alternately change e g Q with each click D NOTE Six types of screen background color are prepared for the Software Warm Dark Cool Dark Monochrome Dark Warm Light Cool Light and
69. e images NOTE For further information on auto brightness adjustment applied to bright and dark regions refer to 5 2 3 Dynamic Range Analysis and 5 3 2 Dynamic Range Adjustment under Appendix in the Setup Guide NOTE These adjustments are not available when the REX option is selected for Brightness Adjustment mode see 7 2 3 LUT look up table curve The raw data generated by the detector s sensor panel is automatically processed using one of the preset imaging parameters LUT curves that suit several anatomical parts and is shown in the image view pane as a film like image The LUT curve changes reflecting changes made using the Brightness and Contrast controls The stronger the contrast the steeper the curve becomes and the weaker the contrast the flatter the curve becomes Note that this curve serves as a rough indicator Histogram This indicates the pixel value distribution of the raw data generated by the detector s sensor and is used as a rough indicator of the X ray dose The x axis of this histogram is logarithmic The more the histogram leans toward the right the higher the dose The adjustment of processing controls will not affect the histogram 6 Post Processing Images Histogram LUT curve monpogeccrocag OO mI Examination screen Brightness ImageProc Access level selectors indicator 4 ontrast St SI Bright region Dark region adjustment slider adjustm
70. e on the EXAM gt Examination screen For details on operations see step 1 in 4 3 Enter descriptions in the Series Information tab Under the Series Information tab enter information in the Series Description box An option can be selected from the drop down list as well as directly entering a text Before Chest AP X wise Chest AP X wise When replacing the protocol select the target protocol from protocol trays hen replacing the protocol select the target protocol from protocol trays Series Image Information Series Information Image Information wi v Series Description box SAO Series Information Image Information Patient Orientation L F Operator Name box Patient Orientation box ox TE Series Information tab Image Information tab NOTE Frequently used descriptions for some series information items can be preset For details refer to 2 4 2 in the Setup Guide I oen 91 4 Conducting Examinations 92 3 Record an operator name Enter an operator name in the Operator Name box An option can be selected from the drop down list as well as directly entering a text 4 Record a body part Select a body part from the Body Part drop down list 5 Record a patient orientation In the Image Information tab select a patient orientation from the Patient Orientation drop down list 6 Set the information Click OK 5 Reviewing Images 5 1 Reviewing ima
71. e protocols are shown in the study information pane Click the preview thumbnail of the target protocol and then click Stitch 3 Close the Stitch Screen Click OK to save the changes for the stitched image 180 9 Troubleshooting Remedies 9 1 Confirming details of the problem 9 Troubleshooting Remedies If the error persists If you encounter an error that is not described in this chapter or if an error persists after trying the measures described in this chapter contact your service engineer Before making your inquiry make a note of the error type error code and other details referring to the error dialog described below or the Log Viewer screen refer to 3 2 in the Setup Guide 9 1 Confirming details of the problem 182 If an error occurs error button or Re warning button will appear at the top of the screen If A appears click it to show the error dialog box Search for a solution in the error and warning lists by error type error code and description NOTE Usually appears accompanied with an error dialog box except when an examination is in progress If only appears Click it to show the error dialog box after the examination is ended Error code Error Detail Error Code W020202001 ime 32 PM Description The detector temperature has reached warning levels Description Click to show Additional Information additional r information Error dialog box Click to close th
72. easurement Correct Correction of Magnification SOD 1414 2 mm SID 1000 mm SID box ImageProc Measurement Annotation Measurement panel To correct the measured values enter or modify the values in the SOD and SID boxes and then click Correct NOTE The measured value in height difference mode see 6 3 4 will also be corrected 6 Post Processing Images 4 Exit measurement mode Click Measurement 6 3 2 Measuring the angle of a specific part EXAM PAST 5 i ea Worklist Manual lt i Examination i YC es E inf ames Smith Dok 117 1671953 8 i wen a gt T 0il Chest AP Handles Measured angles a Click to show and EXAM gt Examination screen hide all line angle objects Delete a ies Click to show and orrection of Magnification orrect hide the scale at the bottom of the image ine 3 view pane ImageProc Measurement Annotation sop mm siD mm Measurement NOTE The measurement unit and the scale shown at the bottom of the image view pane can be selected on the system setup screen For details refer to 2 4 1 in the Setup Guide 1 Enable angle mode Click EA NOTE Once angle mode is enabled operations other than step 2 below are disabled Be sure to complete operations through step 2 2 Measure the angle of a specific part Click three points on the image view pane so that an angle is formed by two line
73. ececeseccoecececeececeoe XIV CXDI Control Software NE Operation Manual ccccccccccccccccccccesccccecccccescccsecccceess 1 SATO Cy SANY ariere e EETA E E EA 3 CONTOS erirrarir er EEE EEEE E EE EE tiusssettess eeu reteececon sees 4 T Gerne e O errer aE E E E EA EE AET 9 2 Starting and Shutting Down the Software sesessecececesoecececeececececeececececeececesoo 27 3 Preparing for EXaminatiONS csevc ce cecccaie soesevicenceucecteccnceuceseecens desc ecvieessecencsnreesaas 39 A Conducting Examinations ccccesrscvcauseccrcvnvticrssevcevetancssiacarsiecessviaessisnsieiswseniacesseta 67 9 REVI W Te MO OS E E E 93 6 Post Processing Images csecssessesoecoososesoessessecoscssesoessecoososossesssssesoesoseso 109 F Oer POMCCIONS sorrise er AT 139 8 Stitching images Long length imaging seseesesesescececesescecececoecececesoececeseeceoe 165 9 Troubleshooting RemediesS sesessessesossesossosoesoesosoessesosoososoosoesoesessesoeooeoo 181 ITON acces cancer E E EE OEE EEE EE 204 03282013 Sound Eklin Important Safety Information Note ii Warning Sound Eklin O Read all the instructions before connecting or operating the component Keep this manual so you can refer to these safety instructions This product is intended as a portable digital x ray image capturing system for Veterinary use only not for human use The Mark 1114cw needs special precautions regarding EMC and needs to be
74. ect indicating the measured height between the points appears 1 Sener 2 1 2 The entire edge HU of the segment Ii identifying the S J p baseline 3 The start point of We the measurement eei T a y 4 The end point of T y Height difference the measurement 3 Perform other height difference measurements Repeat steps 1 and 2 To change the position of the height measurement object Click the height measurement object so that handles appear at the four points of the object Drag the baseline or either handle to move the position of the height measurement object To delete the height measurement object Click the height measurement object so that handles appear at the four points of the object and then click Delete To correct the measured values and the scale See step 3 in 6 3 1 for details 4 Exit measurement mode Click Measurement 135 6 Post Processing Images 6 4 Using the Annotation panel Custom annotations created following the procedures below can be embedded on both the screen preview images and on film images 6 4 1 Creating editing custom annotations 7 Enable annotation mode Click Annotation 2 EXAM eee Worklist Custom annotation list Scroll arrows current page total pages Custom annotation list Add Edit Scroll arrows current page total pages E Annotation Text box Place amp Apply Place only j Place amp Add to Place
75. ed in DICOM communication Contact the system administrator E040505020 A response error occurred in DICOM communication Check the destination modality or server etc E040505027 An error occurred in the DICOM printer output Contact the system administrator Click OK to close the dialog box and then contact the system administrator The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E040505028 An error occurred in the DICOM printer output Try again later Click OK to close the dialog box and retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide If the problem cannot be resolved contact the system administrator The problem may be resolved by checking the DICOM conformance statement If this error occurs again inform a service engineer of the error code 194 9 Troubleshooting Remedies E040505029 E04050502A E04050502E An error occurred in the DICOM printer output Contact the system administrator Click OK to close the dialog box and then contact the system administrator The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E04050502C E04050502F An error occurred in the DICOM printer output Try again later Click OK
76. ed protocol Select the target workspace in the Select Workspace list Set the replacement protocol Click OK 19 4 Conducting Examinations 4 3 Reprocessing an image of a complete protocol To reduce the integral dose applied to patients when mis application of protocol has occurred etc an already captured image can be reprocessed using the parameters of another incomplete protocol with the same workspace as that used for the target image protocol 7 Show the Replace Protocol amp Series Image Information dialog box Click to highlight the complete protocol that includes the target image and click the protocol again The selected protocol name appears in the Before box A 0000001 cs Chest AP X wi gj an Vlei e WS CXDISOG Z ca O ii vw WS CXDI50G an mia ws cxosos ae za zi Complete protocol CI aa highlighted ame Gj if EXAM gt Examination screen Protocol list Before Before box When replacing the protocol select the target Series Image Information option see 4 9 Click to cancel the operation Replace Protocol amp Series Image Information dialog box 80 4 Conducting Examinations 2 Select the replacement protocol used for reprocessing Click the replacement protocol in the protocol list The selected protocol name appears in the After box NOTE Only replaceable protocols whose workspaces are i
77. efer to the Setup Guide refer to 2 4 1 in the Setup Guide for details on setting essential information items Setup Guide refers to the CXDI Control Software NE Setup Guide 11 1 Getting Started 1 Getting Started 1 3 Workflow diagram for a general radiographic examination PAST tab gt Recall Exam NOTE The following example illustrates a case in which the Software is used under interoperability services with the HIS RIS database EXAM tab Reviewing images on the PAST gt View screen see 5 2 Post Processing Images see chapter 6 Manually printing images in AS Edit Exam screen phe eg gt View screen Local disk of the see l image capture Log In computer lt Examination Canon pte Start Screen CXOI Control Software NE Configuring protocols Starting the Software Start Exam see 2 1 Start Exam _ EXAM gt Worklist screen EXAM gt Examination screen Before expos re Suspend Exam N Selecting study orders Worklist tab see 3 1 awe Conducting Examinations see chapter 4 Exposure switch Captured images Screen transition l EXAM Examination screen Aftemexposure Send to Storage Screen buttons Start Exam EXAM_ gt Manual screen j bad i omm Dee Reviewing Images see chapter 5 Post Processing Images see chapter 6 Printing
78. enl See 6 1 4 OK AE in pene ipa User ii AEE Hes Foe rae ey i PUL Sucre ae Cece To finish panning Click OK 115 6 Post Processing Images 6 1 4 Zooming images Images can be magnified for review in detail and then reduced to the original size at the same time the original position will be resumed Pixel to pixel and high resolution display modes are also available NOTE The change in magnification does not affect the size of the images that are transferred to a storage server printer or other destination directories 7 Zoom in the image Click repeatedly The image is enlarged from the center of the cropped image in four steps To enable pixel to pixel display mode Click repeatedly until changes to EE and then click KRW PAST Ai a E Mamual H Examination O h 1 Be Finfo James Smith Educate This Dol i af TEES k DoB 11 16 1953 58 Years ey Dowel a i End Exam To review images in high resolution mode Click HQ Fine textures will be clearly displayed at the same magnification when HQ is clicked NOTE Usually the resolution of a reduced image is automatically adjusted depending on the image magnification In such cases HQ enables original resolution display at the same magnification On the other hand magnifies the image keeping the automatically adjusted resolution To zoom out of the image Click repeatedly The enlarged image display is reduced
79. ent slider 7 Show the histogram and LUT curve Click FF Clicking FF toggles between the on off state of the histogram and LUT curve 2 Increase or decrease the brightness of bright region To increase drag the bright region adjustment slider to the right To decrease drag the bright region adjustment slider to the left 3 Increase or decrease the brightness of dark region To increase drag the dark region adjustment slider to the right To decrease drag the dark region adjustment slider to the left 127 6 Post Processing Images 6 2 2 Adjusting the overall brightness and contrast or _ 7 ka Brightness gt Brightness control EXAM gt J Examination a ca Contrast control screen ImageProc Measurement Annotation 1 Adjust the brightness Rotate the scroll wheel on the mouse or click the arrows of the Brightness control To increase move the slider to the right To decrease move the slider to the left NOTE Fine adjust the brightness in a range of 10 to 10 relative to the Base Brightness value The supported adjustment range depends on the Base Brightness value In some cases the range may be narrower than 10 to 10 For details on Base Brightness control see 7 2 3 NOTE When adjusting images where negative positive inversion is applied the moving directions of the Brightness control are reversed 2 Adjust the contrast Rotate the scroll wheel on the mouse or click the arrows of
80. ere may be a problem in the captured image Check the image and retry the examination W050501013 A grid ID loading error was detected Check if the grid is properly attached If the problem cannot be resolved inform a service engineer of the error code W050501015 A grid error may have caused an image abnormality Click OK to close the dialog box and check the captured image If there is a problem in the image inform a service engineer of the error code 203 Index A Access level 154 Accession Number 44 Age 59 Anatomical Part 155 Annotation Creating editing 136 Preview annotation 71 96 Showing hiding 71 Arranging images Automatically 144 Manually 149 Authentication 31 Auto 157 B Background program screen 35 Binding data 89 Birth date 59 Body part search mode 53 Brightness Base Brightness 157 Gradation 156 Highlights and shadows 126 Overall brightness 128 ROI 118 Brightness Adjustment mode 157 Button 10 C Calibration 29 Category search mode 56 Complete protocol Reprocessing images 80 Contrast Base Contrast 157 Overall contrast 128 Shape enhancement 158 Crop 120 D Directory options 98 Dynamic Range Adjustment 159 204 E Edit Exam 51 Edit Patient Information 62 Edit Study Information 48 60 Emergency 64 Enhancement 158 Error 182 List 186 EXAM 10 12 Exam 42 Examination Ending 76 Recalling 100 Restarting 85 Starting 71 Suspending 85 Exposure mode 70 Expo
81. error occurs again inform a service engineer of the error code 200 9 Troubleshooting Remedies 9 1 3 Warning list W020202001 The detector temperature has reached warning levels W020202002 The detector temperature has reached dangerous levels Suspend the examination see 4 6 and wait until the temperature decreases Then restart the suspended study order W020202003 The detector is not available Irradiation has finished Click OK to close the dialog box and then continue the operation W020202004 The detector battery is weakening Charge the detector battery Click OK to close the dialog box and charge the battery of the wireless detector If the optional wired connection is available switch to the connection For details on the wireless detector refer to the Digital Radiography CXDI series User s Manual W020202005 The specified disk space could not be cleaned up Check the target data volume to be deleted and then retry deletion see 5 3 W030203003 The internal temperature of the detector exceeds the upper limit Suspend the examination see 4 6 and wait until the temperature decreases Then restart the suspended study order W040100045 Calibration data is invalid Update the calibration data Click OK to close the dialog box and then calibrate the detector refer to 3 5 1 in the Setup Guide W040100052 The detector issued a warning Click OK to close
82. es digital power outlet Nema radiographs 5 15 34 671 Detector Handle Unit for Canon 80C Sound Eklin Page xi The Mark 1114cw System continued The Mark 1114cw Key Connections Overview 10 121 Min X ray Sync Cable for Mark 1114cWw i A 24 122 Keyboard with Touch Pad q J e nterruption to the USB CTD NES keyboard or Mouse can be cleared by re mating the connection to the system lt 10 Ethernet Patch Cable lt 10 171 Equine 20 IEC NEMA Power Extension Cord Sound Eklin Page xii The Mark 1114cw System continued Connecting the Generator The sync cable should stay connected to the generator and should be stored in the generator box 1 Plug the Min X ray Sync Cable 10 867 into the Mark 1114cw Align by red dots on each end of the connector 2 Plug the hand switch end of the Min X ray Sync Cable 10 867 into the generator hand switch port Min X ray Sync Cable 10 867 Sound Eklin Page xiii The Mark 1114cw System continued Powering Up the Mark 1114cw System 1 Plug the female end of the power cable into the power cable slot on the Mark 1114cw box Plug the other end into a grounded power outlet see page iii Power Requirements 2 With the cables connected turn on the Mark 1114cw by pressing the power button on the top of the unit Power Button with LED Light 10 171 Equine 20 IEC NEMA Power Extension Cord Standard US
83. es the protocol order in the study information pane in descending order For details consult your service engineer Automatic selection of protocols After each protocol is complete the next available protocol is automatically highlighted If the user prefers to manually select a protocol automatic selection can be disengaged and the user can click on an incomplete protocol to select it For details refer to the Automatic Next Protocol Selection option under 2 3 1 in the Setup Guide 74 4 Conducting Examinations If an image transfer has been interrupted If an image transfer has been interrupted by a wireless detector communication error the following dialog boxes appear Follow the instructions and click Retry to resume image transfer Confirmation The image transfer has been interrupted by a wireless detector communication error Wait until communication resumes without turning off the detector power and then retry the transfer Canceling the transfer will erase the image When the detector is used in wireless configuration remove change the position of or keep away from the following obstructive objects to ensure good wireless communication Before retrying an image transfer make sure that the signal strength is strong or medium by checking the signal strength indicator in the system status bar Obstructions between the access point and wireless detector WLAN signal interference source Cancel Retry
84. f is displayed in its attribute icon column Furthermore when the copied study is protected see 3 1 3 ig changes to Eg Attribute icon column aaa ML BAe P Lar wif 000a VES iii Pogai lamet iaga EEEE EEDI yI AUL Bcn POCTU lames smi F119 t Copied study BELLereer aA 100l Pe Mar lohra SAE ee mar EEE BE Ede T GE Recall Copied aaa Exam PAST gt Past List screen 5 2 4 Reviewing images saved in storage media Images saved in storage media such as an external HDD can be reviewed NOTE Except for reviewing operations such as post processing copying studies restarting studies and zooming in out are not enabled for images saved in storage media 7 Select the volume containing the target study from the PAST gt Past List screen Select Disk Storage for the directory option 2 Select the target study Click a study to highlight it 104 5 Reviewing Images 3 Review the study Click Recall Copied Exam The selected study appears in the PAST gt View screen Protocol ACC for the information for each selected image image appears Current total studies Current total images ia Studies 4 76 Images_ a A AE yy oe A PAST gt View screen Back To List NOTE Age in the patient information pane remains blank during review To navigate the images in the directory Click E E to show previous next image Click E E t
85. for Examinations 7 Show the Select Workspace dialog box Select a study order and then double click the thumbnail in the target protocol in the study information pane Protocol Name Chest AP L wise Available workspaces The connection with the detector is incomplete or the power box is turned off Workspace name NOTE A battery indicator and a signal strength indicator are shown on the workspace for wireless detectors For the wireless detector refer to the Digital Radiography CXDI series User s Manual Example of workspace indicator for wireless detectors WS CXDI70C Battery indicator Signal strength indicator A 60 100 charge ial Strong A 9 59 i Medium j 5 8 id Poor fl 4 or less Yee No signal When the indicator changes to or and it starts to flash a warning or error dialog box appears to prompt the user to recharge the battery 50 3 Preparing for Examinations 2 Select the target workspace Click the target workspace and then click OK 3 1 5 Configuring protocols Study orders are modified by including additional protocols deleting existing protocols or arranging the order of existing protocols 7 Show available protocols Select a study order and then click Edit Exam in the study information pane eee Edit Exam s T Click to shrink and a expand the protocol list Click to navigate the pages on the list Protocols included
86. g Click OK to close the dialog box Ensure enough HDD s free space and retry reading E040501011 Cannot continue the processing because a file already exists at the specified storage destination Check the setting information Click OK to close the dialog box Delete all files in the folder designated as the storage and then retry the previous operation If the destination folder cannot be identified consult the system administrator If this error occurs again inform a service engineer of the error code E040501012 Cannot continue the processing because access to the specified storage destination was denied Check the setting information Click OK to close the dialog box right click the folder designated as the storage select Property gt Security tab change the access privileges and then retry the operation from the start If the destination folder cannot be identified consult the system administrator If this error occurs again inform a service engineer of the error code E040501013 Cannot continue the processing because there is not enough space at the specified storage destination Check the setting information Change the destination folder Or ensure enough HDD s free space and retry the operation 191 9 Troubleshooting Remedies E040501014 DICOM GSPS output was halted because the object image transfer was incomplete Try again after object image transfer Click OK to close
87. ge server PACS to save captured images For details on the setting for the destination directory refer to 2 6 1 or 2 6 5 in the Setup Guide When starting on the PAST gt Past List screen Click the target study in the Study List eee E a TEE EBPs 14 2012 DE AM PoODooO ay Bohnenn WO FFEFEEI Click to select all studies PAST gt Past List screen To select multiple studies Follow step 2 in 5 3 but do not click at the start of the operation 1 Show the Output Settings dialog box Click EM 2 Enable PACS or storage media Select a storage server name or storage media name option under the Storage or Disk Storage option To disable the storage server or storage media clear the option To save the changes made in the Output Settings dialog box Click Save to System The changes will be reflected in the default setting that can be configured in the Connection tab in the system setup screen and also applied to subsequent printing and transfer operations 152 7 Other Functions 3 Transfer images In the PAST gt Past List screen Click Send Exam to transfer the images in the selected Exam In the PAST gt View screen Click Send Image to transfer the current image or click Send Exam to transfer the images in the current Exam NOTE Rejected images can be transferred to the preset directories using only Send Image 153 7 Other Functions 7 2 Using the Image Processing
88. ges Remain Duplication of the original protocol To reject partial images Click Reject The preview thumbnails of the rejected protocol are crossed out see 4 5 NOTE Even if the rejected protocol is restored the partial images of the rejected protocol are not carried over to the restored protocol To suspend an examination Be sure to capture all the necessary partial images and then click Suspend Exam see 4 6 The EXAM gt Examination screen changes to the EXAM gt Worklist screen After suspending the examination partial images can be stitched proceed to step 7 if two or more images have already been captured NOTE Further image capturing is not available using the suspended protocol NOTE Depending on the X ray generator if two or more images have already been captured the examination can be ended from the X ray generator 172 8 Stitching images Long length imaging Check the automatically aligned images Check that two pairs of stitch markers on the overlapped images are fully matched in the Stitch Screen i e a pair of stitch markers appears For details see 8 3 1 Aligned images Iz The area shown in i the image view pane is indicated by the orange borders Image view pane Poin nye Stitch Screen NOTE If stitch marker detection fails the misaligned image appears accompanied by an error message In such cases manually align the partial images For det
89. ges on the EXAM gt Examination screen 5 2 Reviewing images on the PAST gt View screen 5 3 Deleting studies from the PAST gt Past List screen This chapter explains how to review images immediately after image capturing in the EXAM gt Examination screen as well as later in the PAST gt View screen Workflow i mAte OP aa EXAM gt Examination screen Post Processing Images see chapter 6 EXAM gt Examination screen Conducting Examinations see chapter 4 EXAM gt Examination screen 5 1 Reviewing images on the EXAM gt Examination screen TEONE Image arrangement screen Arranging and printing images automatically see 7 1 2 PAST gt Past List screen PAST gt View screen 5 3 Deleting studies from the 5 2 Reviewing images on the PAST gt Past List screen PAST gt View screen 94 95 5 Reviewing Images 5 1 Reviewing images on the EXAM gt Examination screen NOTE Itis best to disengage the Ready status of the next available protocol during a prolonged review Click Unselect in the study information pane so that Not Ready appears in the system status bar 7 Select a target radiographic image thumbnail Click a preview thumbnail of a complete target protocol in the study information pane The image appears in the image view pane in single view mode single view The selected view mode button is highlighted Click to show and hide preview
90. hange passwords To add or delete user names it is necessary in advance to log in to the Software under a user name that has the Administrator role For details refer to 2 2 in the Setup Guide Automatic logout function The Software automatically logs out after 10 minutes of inactivity To change the setting of the automatic logout function refer to 2 3 1 in the Setup Guide The error button and warning button An error button or M warning button will appear at the top center of the screen if the Software experiences a problem If this happens see 9 1 31 2 Starting and Shutting Down the Software 2 2 Shutting down the Software NOTE Itis necessary to shut down the image capture computer once a day at closing etc to maintain the optimum performance of the Software If a study is currently being examined Be sure to click End Exam in the examination screen before shutting down the Software See step 6 in 4 1 for details on End Exam 7 Show the system setup screen Click GE i TUL m Hil EXAM gt Worklist screen User NameCuciuser User Administration System Settings Customize Display Annotation j Lise Mame Role Operator Name System setup screen NOTE A dialog box related to image arrangement may appear For details see NOTE in step 4 in 7 1 2 To log in under another user name Click Logout click OK in the confirmation dialog box and then select another u
91. he previous operation Arrow buttons Auto 3 Arrange the selected partial image Drag a partial image to fully overlap the stitch markers To finely adjust the position While the image is selected click the arrow buttons One click of the button moves the image one pixel in the same direction as the arrow indicated on the button To redo automatic alignment Click Auto 176 8 Stitching images Long length imaging To crop a partial image Click the target partial image to select it and then click ki The image edges change to green Click Select to show the handles on the edges drag the handle to crop the image and then click OK to set the change operation Handles mS Click to cancel the Cj Select Click to exit cropping mode without saving any changes To rotate a partial image 90 degrees Click the target partial image and then click or E D Each time the buttons are clicked the image rotates clockwise or counterclockwise 90 degrees 177 8 Stitching images Long length imaging To freely rotate a partial image Click on the target partial image to select and click ED Then click on the image to specify a pivot point and then drag the image to rotate Outline for positioning Pivot point Edge Enhancement control To enhance the edges of the object as an alignment aid Rotate the mouse wheel on the Edge Enhancement control or click the arrow on the
92. he change does not affect the captured image 164 8 Stitching images Long length imaging 8 1 What is long length imaging 8 2 Capturing and stitching images 8 3 Realigning modifying and stitching partial images This chapter explains how to create a long length image that shows the entire spine or the entire lower extremities full spine or full leg in a single image by stitching together two or more original partial images Automatic image alignment and other manual adjustment features are also explained Workflow Ey Eia Marker Tapke AAH eo Yaari na A 0000010 Stitch 2images Remain gt 2 image s v i E gt EXAM gt Examination screen before capturing an image EXAM gt Worklist screen 8 2 Capturing and stitching images PAST gt View screen 8 3 2 Modifying long length images in the PAST gt View screen Image arrangement screen Arranging and printing images automatically see 7 1 2 166 Stitched image will appear here Remain 1 image s riper EXAM gt Examination screen after capturing the first image EXAM gt Examination screen after stitching images i a Stitch Screen 8 3 1 Aligning partial images 167 8 Stitching images Long length imaging 8 1 What is long length imaging The long length imaging feature generates image such as full spine and full leg images These images are used to diagno
93. he height difference In preoperative postoperative diagnosis for knee replacement arthroplasty the height differences between the right and left sides of the pelvis or kneecaps are measured to check the alignment of the body For long length images that capture the entire spine and or lower extremities see chapter 8 aur nia Michael Taylor ime Dob 1 14 4 GAG EA Waar LIVIE 1 Years i TEA Handles Measured height difference 4 ced emp uae TD es filer py dg mH Tail Epa Tinian AF3 Click to show and hide all line angle objects Delete ae aaa Correction of Magnification Correct Click to show and hide the scale at the bottom of the image ImageProc Annotation view pane SOD 1414 2 mm SID 1000 mm Measurement NOTE The measurement unit and the scale shown at the bottom of the image view pane can be selected on the system setup screen For details refer to 2 4 1 in the Setup Guide 7 Enable height difference mode Click J The on screen Help for measurement location settings is available at the top of the image view pane NOTE Once height difference mode is enabled operations other than step 2 below are disabled Be sure to complete operations through step 2 134 6 Post Processing Images Measure the height difference between two specific points Click four points on the image view pane to determine a reference line and two measurement points A line obj
94. he recovery mode screen The computer enters low power mode and the monitor display enters standby mode As the memory contents are preserved during sleep mode the computer quickly resumes working 34 2 Starting and Shutting Down the Software To put the image capture computer to hibernation mode Click PC Hibernate in the recovery mode screen The HDD of the computer and monitor display turn off As the memory contents in recovery mode are preserved during hibernation mode the computer resumes working faster than restarting the computer NOTE Do not enable sleep or hibernation mode using the power switch on the image capture computer NOTE The image capture computer resumes in recovery mode from sleep or hibernation NOTE PC Sleep and PC Hibernate can be hidden For details consult your service engineer To exit the Software and restart the image capture computer Click PC Restart in the recovery mode screen NOTE When Shutdown in the recovery mode screen as well as Shutdown in the Shutdown Confirmation Dialog Box is clicked the Controller is exited If the Software is unexpectedly aborted and the recovery mode screen appears Click CXDI Restart to restart the Software and continue operations NOTE If an error persists after restarting the Software by clicking CXDI Restart restart the image capture computer 35 2 Starting and Shutting Down the Software 2 3 Conducting offline examinations When
95. hen retry the data transfer from the Process Viewer refer to 3 3 in the Setup Guide E04060000B Cannot retry the process as an error occurred Delete the failed process in the process viewer locate the process in the PAST gt Past List and then retransmit the process Delete the data transfer error log from the Process Viewer refer to 3 3 in the Setup Guide Then resend the image from the PAST gt Past List screen see 7 1 5 196 9 Troubleshooting Remedies E04060000C The system is attempting to transfer old study information created before data rebinding Delete the corresponding process as it cannot be executed Delete the data transfer error log from the Process Viewer refer to 3 3 in the Setup Guide The image including old study information cannot be transferred as the rebinded image has been successfully transferred E040700006 Failed to load the image file If the problem is not resolved contact a service engineer Click OK to close the dialog box and then retry the previous operation E040800100 Cannot start the examination as an invalid protocol exists in the study Delete the invalid protocol and retry the examination Click the suspended examination including the invalid protocol in EXAM gt Worklist and then Edit Exam to delete it See 3 1 5 EO40D0001F Failed to free up the hard disk If the problem is not resolved after restarting contact a service engineer
96. ient mix up and a misdiagnosis may cause harm to the patient While shutting down CAUTION Do not turn the image capture computer off before it automatically shuts down Doing so may result in damage to the hardware and or destruction of data Contents Safety SUIMIMGNY rromii aaa a a aain 3 1 Getting Started Wet MEO GUCE OMI rran a a aE a aaa 10 1 2 INOCA TION S caian a a a E a a aa 10 t2 T Sereen name Sroine E a a a ae a a 10 k22 BUON S cienia a a a aA 10 t23 M u use wheeloperatloNnS isinara aaa ANAR AAE AANE KANAE 11 1 2 4 Touch screen display operations cccssccscesensenscnsensensensenseneesesensensensensensenseneeseesensensensenses 11 N20 TRELELENGES aaraa A AAE AEE 11 1 3 Workflow diagram for a general radiographic examination ssssssssssnnnnnnnnnne 12 1 4 Part names of screens Quick reference s ssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nan 14 1 4 1 EXAM gt Worklist screen ssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnnm nnna 14 1 4 2 Study information pane and Protocols ccececesensenseceeenseensceseenseeseceseensensesessnsenseensenneens 15 LAS Edt EXAM SCEOG IN irnia aaa AAAA AANA ENNEN AANA NANE 16 14 4 EXAM gt Manual SCre6n anosa aaa a a a oa aa 18 1 4 5 EXAM gt Examination screen sssssnsunnunnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnnm nnmnnn nnna 19 146 PAST gt Past List Serei iniiaiee aaa aaia 20 1 4 7
97. ing Physician Reading Physician Enter the relevant physician s name Study Description Users can freely enter study information Institution Name Enter the name of the institution where the examination is conducted 60 3 Preparing for Examinations NOTE Frequently used descriptions for some study information items can be preset For details refer to 2 4 2 in the Setup Guide Set the detailed study information Click OK To add a study order Click Add Study To delete a study order Click the target study order to highlight click Delete and then click OK in the confirmation dialog box Configure protocols See step 2 in 3 1 5 for details on operation Start examination Proceed to 4 Conducting Examinations 61 3 Preparing for Examinations 3 3 2 Modifying patient information 7 Show the Edit Patient Information dialog box Click Edit in the patient information pane 2 y 20_ 1982 Age 30 Years i a P000101 Sex Male Female Other Click to cancel the operation OK Cancel Be sure to confirm that the entered information patient name ID number birth date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient 2 Modify the patient information See step 1 in 3 3 1 for details on operation 3 Set the information Click OK 62 3 Prepa
98. ing of patient information schedule and examination details issued by a referring physician A group of studies for one patient Details of examination procedures which include the following information Workspace grid image processing parameters and DICOM attributes In this Software a protocol is associated with a specific workspace and that pair is shown as a protocol button In other word according to the requirements of an individual site multiple buttons are created for one protocol and all differ from each other in the workspace They are organized in protocol lists Therefore users can select a pair including a protocol and workspace with one click of these buttons See 3 1 5 Details of a protocol that specify the detector used and the posture of the patient during the examination 3 1 1 Acquiring study orders from the HIS RIS database EXAM gt Worklist Study orders are automatically acquired from the HIS RIS database and listed when the user logs in NOTE An HIS RIS database introduction is required to list study orders on the worklist Consult your service engineer for details On Line Off Line selector indicator tab HDD free space AN Exam Mew Exam _ Pende Eam Restarted Erim icon ES S Column header Study orders Click to create an emergency study sults rt Exe order EXAM gt Worklist screen 3 Preparing for Examinations If the EXAM gt Worklist screen does not ap
99. ire the target order by narrowing down the study orders using Refresh Option see 3 1 1 To change the maximum number of orders that can be listed contact a service engineer 189 9 Troubleshooting Remedies 190 E040500004 Invalid studies contained in the acquired data are not displayed Check the data identical to the acquired ones on the RIS database etc Show Additional Information to check the number of the invalid orders and then click OK to close the dialog box Check the study orders that failed to be shown The Patient ID and Study Instance UID of the orders may be invalid In that case correct the study order information and retry the acquisition see 3 1 1 If this error occurs again inform a service engineer of the error code E040500005 Invalid values in the received tag have been replaced with blanks Check the data identical to the acquired ones on the RIS database etc Show Additional Information to check the study orders that failed to be shown and then click OK to close the dialog box Correct the study order information and retry the data acquisition See 3 1 1 If this error occurs again inform a service engineer of the error code E040500006 Received data includes characters that do not exist in the CXDI system s character set The characters may not be displayed correctly If the problem is not resolved contact a service engineer Click OK to close the dialog box Supplementar
100. is the a c mains voltage prior to application of the test level Sound Eklin Guidance and Manufacturer s Declaration for Electromagnetic Compatibility EMC Electromagnetic Immunity continued Immunity Test IEC 60601 Compliance Electromagnetic Test Level Level Environment Guidance Conducted RF 3 Vrms 150kHz 3 Vrms Portable and mobile RF communications IEC 61000 4 6 to 80 MHz equipment should be used no closer to any part Conducted RF 3 V m 80 MHz 3 V m of the CDXI 80C Wireless including cables IEC 61000 4 3 to 2 5 GHz than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separations distance d 1 2 P d 1 2 P 80 MHz to 800 MHz d 2 3 P 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey 2 should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol co Note At 80 MHz and 800 MHz the higher frequency range applies These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflections from structures object and people a Field strengths from
101. ity for unexpectedly terminated examinations Unexpectedly terminated examinations are listed in the EXAM gt Worklist or EXAM gt Pending List screen with Pending indications in the Study Status column NOTE Examinations listed in red indicate that they were abnormally terminated during processes Indications and operations for the listed items are identical with those for examinations that are suspended by clicking Suspend Exam To rebind patient information with that of another study order Proceed to 4 7 Rebinding other study information with that of the suspended study order NOTE After rebinding incomplete protocols in the study order will be deleted NOTE Once images are transferred to PACS by clicking Send to Storage the corresponding images stored in the image capture computer cannot be modified or post processed However it will be enabled by patient information rebinding To restart the suspended study order Select the suspended study order in the EXAM gt Worklist or EXAM gt Pending List screen and then click Start Exam 85 4 Conducting Examinations 4 7 Rebinding other study information with that of the suspended study order When an examination was started for a different patient by mistake or another reasons suspend the study order see 4 6 rebind the correct study information with the suspended study order as explained in the following procedures and start the examination again
102. king the destination server or the DICOM conformance statement If the problem cannot be resolved inform a service engineer of the error code W040505030 The transmission was complete normally However the CXDI system received WARNING status from the destination DICOM printer Check the DICOM printer Check the DICOM printer For details on Printer Status refer to Annex C 13 9 1 in the DICOM standard Parts Information Object Definitions or the DICOM conformance statement 202 9 Troubleshooting Remedies W050501002 05050 1004 A Flash ROM error was detected in the detector Contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software See 2 2 If this error occurs again inform a service engineer of the error code W050501005 A grid error may have caused an image abnormality Click OK to close the dialog box There may be a problem in the captured image Check the image and retry the examination W050501007 The internal temperature of the detector is close to the upper limit Do not leave the detector in the Ready condition Click OK to close the dialog box click Unselect and wait until the temperature decreases W05050100E W05050100F An error was detected in the detector Inform a service engineer of the error code W050501011 The transfer of the image data was stopped Click OK to close the dialog box Th
103. lect a failed protocol Click the target complete protocol in the study information pane 2 Start duplication of the protocol Click Retake Clicking the button changes Reject to Restore The Series Image Information dialog box appears Rejected protocol Series Information G i A 0000001 Chest AP Hwise 1 WS CXDI50G Patient Orientation Image Information CON D Chest AP L wise Q 2 WS CXDI50G Rejection Reason TH a LJ al Rejection Reason List Rejection Reason List Retake Reject Restore Duplication of the original protocol Click to cancel the ED a OK operation Series Image Information dialog box Image Information tab Select a patient orientation and enter the reason for rejection Select an option in the Patient Orientation box and fill out the Rejection Reason box The reason can also be selected from the Rejection Reason List For details on Rejection Reason List management refer to 2 4 2 in the Setup Guide l onee 83 4 Conducting Examinations 4 Set the duplicated protocol Click OK The preview thumbnail of the selected protocol is crossed out and a duplication of the original protocol appears as an incomplete protocol To restore the original image Click Restore The original failed protocol resumes and the duplicated protocol is deleted NOTE After the image of the rejected original protocol is reprocessed using ano
104. lick to clear all narrowing conditions Refresh eens 43 3 Preparing for Examinations Enter any narrowing conditions in the Search For Study List pane Three of the following information titles can be selected for the narrowing conditions Patient ID Name Accession No Referring Physician Requesting Physician Comment RP ID RP Description and SPS Description Select an option in each title box and then enter any text in its keyword box Note that these three keywords are used as AND search conditions Study Status Specifies the search range from among All Exam New Exam Pending Exam and Restarted Exam NOTE The information titles that can be selected for the narrowing conditions are those currently displayed in the column header For details on the column header settings refer to the Column Headers option under 2 4 1 in the Setup Guide NOTE Patient Name text box can be divided into five components for accommodating family name given name middle name prefix and suffix input For details refer to 2 4 1 in the Setup Guide If the target study orders are not found on the list Click Refresh to restore the available study orders If narrowing conditions are predetermined narrowing down at the point of data acquisition aids in efficient study order selection Click Refresh Option to show the Refresh Option dialog box NOTE When Refresh and Refresh Option are disabled click Off Line to resume con
105. magnetic environment specified below The user of the CDXI 80C Wireless should assure that it is used in such an environment Compliance Electromagnetic Environment Guidance Emission Test RF emissions CISPR11 The CDXI 80C Wireless uses RF energy only for its internal function Therefore its RF emission are very low and are not likely to cause any interference in nearby electromagnetic equipment The CDXI 80C Wireless is suitable for use in all establishments other than domestic and those directly connected Class A to the public low voltage power supply network that supplies buildings used for domestic purposes 1 Applies to regions where rated voltage is 220 V or higher Not applicable to regions where the rated voltage is less than 220 V Group 1 RF emissions CISPR11 Harmonic emissions IEC 61000 3 2 Voltage fluctuations flicker emissions IEC 61000 3 3 Electromagnetic Immunity The CDXI 80C Wireless is intended for use in the electromagnetic environment specified below The user of the CDXI 80C Wireless should assure that it is used in such an environment IEC 60601 Compliance Electromagnetic Test Level Level Environment Guidance Immunity Test 2 4 6 kV contact 2 4 8 kV air Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Electrostatic Discharge ESD IEC 61000 4 2 2 4 6 kV contact 2 4
106. main 1 image s Ready thumbnail for the next exposure 6 Continue image capturing Repeat steps 3 and 5 quickly until the required number of images are captured instructing the patient to maintain the posture When the last partial image is captured Automatic alignment feature Partial images are automatically aligned by making use of the detected stitch markers and the stitched image appears in the Stitch Screen see step 7 If necessary this feature can be canceled For details refer to 2 3 1 in the Setup Guide JoOnNntinueq 171 8 Stitching images Long length imaging To stitch partial images manually Even if some required partial images are left undone already captured images can be stitched Click Stitch after two or more images are captured Images are aligned by making use of the detected stitch markers and the stitched image appears in the Stitch Screen NOTE If Stitch is clicked before capturing all the necessary partial images further image capturing is not available To recapture partial images Click Retake A duplication of the original protocol appears next to the rejected protocol of which the preview thumbnails are crossed out See 4 4 NOTE The partial images of the rejected protocol are not carried over to the duplicated protocol When Retake is clicked after the first capture Rejected protocol Preview thumbnail first image of the rejected protocol Stitch 2ima
107. n 6 1 7 page 120 Mask 6 1 8 page 123 Retake 74 4 page 83 Reject 74 5 page 84 Reset 76 1 page 112 Undo button 6 1 page 112 1 Getting Started 1 4 9 Image Processing panels A v NI Image Processing al 1 2 B s J lt Brightness o gt ImageProc Measurement Annotation Basic image processing Level 1 A Show hide selector for histogram and LUT curve 6 2 1 page 126 B Access level selector indicator 6 2 page 126 7 2 page 154 C Brightness and Contrast controls 76 2 2 page 128 Image Processing FF ity mye M nia o a E tyramic ange Aajurmant Noise Reduction IO 1 moO Grid Suppression C Sharpness Adjustment Y Peripheral Mask K Save as Default L ImageProc Measurement Annotation Advanced image processing Level 2 3 Anatomical Part control 7 2 2 page 155 LUT control 77 2 3 page 156 Enhancement control 7 2 4 page 158 Dynamic Range Adjustment control 77 2 5 page 159 I 17 mM O Noise Reduction control 7 2 6 page 161 Grid Suppression control 7 2 7 page 162 Sharpness Adjustment control 7 2 8 page 163 Peripheral Mask control 77 2 9 page 164 Save as Default 77 2 1 page 154 T A S 23 1 Getting Started 1 4 10 Measurement panel Measurement Correction of Magnification Correct SOD 1414 2 mm SID 1000 mm ImageProc Measurement Annotation A B Cc D
108. n the indication changes to p or and it starts to flash a warning or error dialog box appears to prompt the user to recharge the battery When a wide display monitor not a 4 3 monitor is used the image view pane in the EXAM gt Examination screen can be expanded fully in the vertical direction by shifting the tabs and buttons located above the pane to the right For details consult your service engineer Protocol sort for efficient workflow Users can arrange the order of incomplete and complete protocols in the study information pane Workspace Sort Groups protocols that have the same workspace across the boundary between study orders Study Sort Restores the original order of protocols on the basis of study Clicking the button toggles it between Workspace Sort and Study Sort NOTE While image data is being transferred in the background the data transfer indicator or 4 flashes see 1 4 1 If the transfer has priority over the examination wait until the or indicator goes off and then click Start Exam appears during data transfer to the PACS server and printers appears during data transfer to the storage media such as an external HDD 4 Conducting Examinations 2 Select the target protocol If necessary click the incomplete target protocol in the study information pane and confirm that the indicator changes from Waiting to Ready in the system status bar NOTE Ifthe Not Ready and i
109. nce on the screen the masked area appears black on the images transferred to a storage server or printer Enable mask edit mode Click Mask 2 Show the specified area Click to highlight The currently specified area appears enclosed by a dotted line A new area can also be specified while a specified area is shown NOTE The masked area on a radiographic image immediately after an exposure is identical to the area outside the detected irradiated field To hide the specified area Click i to clear the highlight 123 6 Post Processing Images 3 Specify the area to be kept Click repeatedly on the image view pane to create boundary points for the area to be kept and then enclose the area by either clicking Preview or the initial click point Double clicking the last boundary point will also enclose the area Up to 12 boundary points can be created OK Click to exit mask edit mode Initial click point Boundary points To specify a rectangular area Click a point on the image view pane and then double click the diagonally opposite point To fit the specified area to the current cropping area Click Eg The area outside the current cropping area will be masked 124 6 Post Processing Images To cancel changes and resume to the area when the mask edit was started Click Reset Apply the masking effect to the image and exit mask edit mode Click OK EXAM PAST Manual Image
110. ndicators appear in the system status bar check that the detector is attached to the system the cable is securely connected the power box is turned on NOTE The user can choose to have the exposure summary displayed on the right side of the system status bar For details consult your service engineer C2 oe Te E a ED Patient posture detector setup Stand aE Table g Cassette Universal Ready thumbnail Workspace name Protocol name Ready status protocol highlighted 3 Arrange the patient in the correct posture Arrange the patient so that the target body part fits appropriately in the irradiated field and instruct the patient not to move during the examination If necessary help the patient to maintain the proper posture i on 13 4 Conducting Examinations 4 Perform exposure Press and release the exposure switch of the X ray generator The Ready indicator changes to Capturing and then Not Ready in the system status bar After processing is complete a preview image appears in the image view pane and then the next available protocol is automatically highlighted Exposure switch Preview thumbnail EXAM PAST a 4 Workiirt Manual E Examination Image view pane Crop frame green e See 6 1 7 Send to Storage End Exam NOTE The series number that indicates the examination sequence can be changed to a number that indicat
111. nection with the HIS RIS database m Name ACC Requested Procedure ID Range Period mm z od vvvy Refresh Option pails aed DALAS mm afo Zl very Relative yours fr i E Click to cancel the operation All Modality E DX _ CR el OK Refresh Option dialog box 44 3 Preparing for Examinations Enter any narrowing conditions in the Refresh Option dialog box and then click OK ID Patient ID Name Patient name ACC The accession number is automatically given to each study order at the point of issue This number can also serve as the study title Refer to Study Information Display in 2 4 1 in the Setup Guide Requested Procedure ID Identifier that identifies the Requested Procedure in the Imaging Service Request Range Period refers to the period of time in which the study orders are to be conducted Relative refers to a period relative to the current time in which the study orders are to be conducted specified by hours in the past future To clear the Range condition select the All option Modality DX refers to digital X ray radiography and CR to computed radiography Be sure to confirm that the entered information patient name ID number birth N caution date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient 2 Select the target stud
112. ness adjustment mode Click ROI 118 6 Post Processing Images 2 Specify an area to serve as the adjustment criteria Drag the pointer on the image view pane to make a yellow rectangular selection that covers the ROI and the brightness of the overall image is adjusted Clicking two diagonally opposite points also make a rectangle ROI Delete Select Ded Nj 2 o OK Click to exit processing mode Handles To adjust the specified area Click Select point any handle to change the pointer to S resize pointer and then drag the handle To cancel the selection Click Delete 119 6 Post Processing Images 3 Exit adjustment mode Click OK 6 1 7 Cropping images A green frame indicating a preset cropping area this information will be transferred to a storage server or printer appears on a preview image immediately after an exposure The preset cropping area can be modified using Jia NOTE Preset cropping area is specified in the Common Cropping Area options in the System Settings tab refer to 2 3 1 in the Setup Guide or the Cropping Area options in the Protocol Workspace Settings screen refer to 3 4 1 in the Setup Guide 7 Enable cropping mode Click Ray A crop frame and handles at the corners and the middle of each side appear on the preview image 2 Specify the area to be kept If handles are not displayed click Select and drag any handle to adjust
113. ngement preview pane NOTE The essential settings for the automatic arrangement feature such as the Film Size and Direction Fit option and other options are configured in the Printer tab For details on operations refer to step 6 under 2 6 2 in the Setup Guide NOTE Automatic arrangement is performed based on the conducted sequence of the studies Although blank segments may remain on some pages depending on the size and shape of images this is the best result and does not indicate a malfunction of the Software 2 Select the target study Click a study tab Images in a single study are arranged under a single study tab So there appear just as many study tabs for the studies as there are in the current Exam 3 Change arrangement and modify the printer arrangement options Operations and settings relevant to image arrangement modification are following To temporarily exclude an image from arrangement preview pane Drag an image from the arrangement preview pane to the Image List To exchange positions of two images Drag one image to the other To specify printer and arrangement options Click the page arrows to show the target page and then specify the following printer and arrangement options These options can be set for each page Size Click on the drop down arrow and select an option from the list The next Destination Printer option will be selected automatically depending on the configuration made in the Prin
114. nnnnnnnnnnnnnn nnnm 85 4 7 Rebinding other study information with that of the suspended study order 86 4 8 Binding study information with the images of an emergency study 89 4 9 Adding information to a Complete ProtOCol ccccscsscesenseseesenseneesensensenensensenees 91 5 Reviewing Images 5 1 Reviewing images on the EXAM gt Examination SCreen c sscsssesseesseenes 96 5 2 Reviewing images on the PAST gt View SCreen c scsssssseeseesecnsensenssenseesens 98 5 2 1 Reviewing images saved in the image Capture computer ccsceseeeseeseeseeseessensenseeeeneees 100 5 2 2 Conducting additional examinations using a complete Study cc secesseensecesesenseeneees 101 5 2 3 Creating images using different image processing parameters of a copied study 102 5 2 4 Reviewing images saved IN storage MECHA csscescesceecenseeseesseesensenseeseessensenseesessensensensenees 104 5 3 Deleting studies from the PAST gt Past List SCreen csscessensenseeseenseees 106 Contents 6 Post Processing Images 6 1 Using the toolbar Basic processing cesessseeseeseenecnsenseenscnsensecnsensensecssensenes 6 1 1 ROtAUNG TIPPING Image S sonca aaa 6 1 2 Inverting a negative image to a positive image and VICE VEFSa cescescesensenseeeesensensenees 6 13 Panning IMAGES ai a aaa A a 6 1 4 ZOOMING IMAGES veintiuno a an aaa ahia a aaea E eaa aE iE aaaea eaaa inini 6 1 5
115. o show previous next study To review other images Click Back To List or the Past List tab and then follow steps 2 and 3 105 5 Reviewing Images 5 3 Deleting studies from the PAST gt Past List screen This Software is configured to automatically delete past study data that is stored in the image capture computer in chronological order from old to recent To prevent useful reference study data from being deleted check the HDD free space icon see 3 1 1 and delete unnecessary studies before the available HDD space decreases too much 7 Switch the Study List for the target directory Click one of the target directory options Directory options E Select All Studies Ee Let PAST gt Past List screen NOTE When the Disk Storage option is selected the Software automatically enters study deletion mode Therefore users do not need to click in step 2 106 5 Reviewing Images 2 Select the target studies Click to exit study deletion mode Select All Studies Click fil to enter study deletion mode and then select the target studies in the list Selected study highlighted a Viiv Bes P Pine EEE E EF mn Pa Reduction target 200000 Aao eI PM PON ida lones GLY gt text box Delete PAST gt Past List screen study deletion mode NOTE Studies with or displayed in the attribute icon column no title cannot be deleted as the Protect Image option is selected For de
116. o the parameter changes made using the Image Processing panel those of the toolbar will also be saved 7 2 2 Automatically processing images by specific anatomical part Anatomical Part control This control is available only in level 3 mode A set of processing parameters optimized for certain anatomical parts and their orientations can be applied to an image for automatic and efficient processing m EXAM gt Examination screen Category Chest Abdomen Category selector Anatomical Part selector Direction Jj Direction selector Enhancement Dynamic Range Adjustment Noise Reduction Grid Suppression Sharpness Adjustment KI SISI SI SI SIS Peripheral Mask Save as Default ImageProc Measurement Annotation Anatomical Part control Narrow down the Anatomical Part options Click on the Category drop down arrow and select an option from the list 2 Specify the target Anatomical Part and Direction options Click on the Anatomical Part and Direction drop down arrow and select an option from each list 155 7 Other Functions 7 2 3 Adjusting the overall image tone LUT control Selectors and controls other than the Brightness and Contrast control are available only in level 3 mode mr Image Processing rr wy 2 3 EXAM gt Image Processing FF Eg 2 Examination Y Anatomical Part Y Anatomical Part screen Curve Shape A LUT select
117. on Select the Bright Region check box to enable this control and then rotate the scroll wheel on the mouse or click the arrows To narrow move the slider to the right To expand move the slider to the left To disable bright region control mode and cancel the effect Clear the Bright Region check box 160 7 Other Functions 7 2 6 Reducing noise in images Noise Reduction control This control is available only in level 2 and 3 modes and it is necessary that Auto mode is selected for the LUT control ci __ iS ea ae i da a i s S lt vs Ea ve 4 mI EXAM gt Examination screen Anatomical Part Enhancement Dynamic Range Adjustment 21 KI SKI SIKS Noise Reduction Effect control Grid Suppression Sharpness Adjustment Peripheral Mask Save as Default ImageProc Measurement Annotation Noise Reduction control 1 Adjust the power of noise reduction Select the Effect check box to enable this control and then rotate the scroll wheel on the mouse or click the arrows To increase move the slider to the right Graininess will increase however the afterimage from moving subjects will be emphasized To decrease move the slider to the left To disable noise reduction control mode and cancel the effect Clear the Effect check box 161 7 Other Functions 7 2 7 Reducing grid lines Grid Suppression control mA fel Examination screen
118. on patient name ID number birth N caution date and sex matches that of the patient If the information is incorrect the resulting patient mix up and a misdiagnosis may cause harm to the patient 2 Select the target study information Click the item in the Study Information list To refresh or narrow down the information Click Refresh If necessary change the narrowing conditions using Refresh Option in advance For details on operation see step 1 in 3 1 1 3 Bind the study information with the image Click OK and then click OK in the Confirm study information to bind dialog box Confirm study information to bind OK to bind data Patricia Jones DoB 6 12 1997 Age 14 Years Click to return to step 2 ID P000004 Sex Female os es oK When the image arrangement screen appears Proceed to 7 1 2 Arranging and printing images automatically 90 4 Conducting Examinations 4 9 Adding information to a complete protocol Replace Protocol amp Series Image Information dialog box Body Part option Click to cancel the operation For further references in diagnosis any description on a series of examination Operator Name and Body Part as well as Patient Orientation can be added to the complete protocol Show the Replace Protocol amp Series Image Information dialog box Click to highlight the complete protocol and click the protocol again in the study information pan
119. on the settings the image arrangement screen that manages printer settings and image arrangement features appears before printing starts In this screen users can check and change image arrangement on film sheets as well as printer settings NOTE For details on displaying the image arrangement screen and other printer settings refer to step 5 and 6 under 2 6 2 in the Setup Guide NOTE Ifthe Film Size and Direction option in the Protocol Workspace Settings screen has been left blank for the protocol used for capturing the image currently selected for printing automatic arrangement feature does not function In such cases click OK in the warning dialog box that appears and then arrange images manually See 7 1 3 144 of End Exam x TTL Study tabs ACC Printer options Size 14INX17IN Portrait Vv Destination Printer Printerl Fit Style Fixed Ratio Image arrangement screen Zoom Ratio _ Arrangement options Add Page Insert Page Click to delete the current page Delete All Page Printable area adjustment Printable area adjustment 7 Other Functions o mage List Arrangement preview pane Click to cancel and exit image arrangement mode Page arrows current page total pages aeaee 145 7 Other Functions 1 Finish an examination Click Edit Exam in the EXAM gt Examination screen All images to be printed in the current Exam are arranged in the arra
120. or Curve Shape Brightness Adjustment Adjustment mode REX 400 0 65535 selector a sae Eee Base Contrast lt Base Contrast 15 gt SSS EE a SS Se lt os ee lads Base Contrast control om Brightness a gt ne Enhancement Y Grid Suppression Base Brightness control KISIS NA e EEEE PIE Asahi Available in all level TEES NA Vv Noise Reduction modes See 6 2 2 Peripheral Mask Grid Suppression Save as Default Sharpness Adjustment K o ImageProc Measurement Annotation Peripheral Mask Save as Default LUT control REX mode for M radiographic images ImageProc Measurement Annotation LUT control Auto mode for radiographic images 7 Select a preset Curve Shape Click on the Curve Shape drop down arrow and select an option from the list SA This s shaped curve has characteristics of standard radiographic films SB This s shaped curve enhances the contrast in bright regions compared to SA SC This s shaped curve enhances the contrast in dark regions compared to SA LN This linear shaped LUT applies uniform contrast throughout all brightnesses 156 7 Other Functions 2 Select Brightness Adjustment mode Click on the Brightness Adjustment drop down arrow and select a mode from the list Auto Mode for automatic tone curve adjustment for uniform brightness in the region of examination regardless of X ray dos
121. or occurs again inform a service engineer of the error code 186 9 Troubleshooting Remedies E020201008 The detector temperature has reached dangerous levels Images cannot be captured until the temperature has dropped Suspend the examination see 4 6 and wait until the temperature decreases Then restart the suspended study order E020201009 Failed to start up the OverwrapSoftware Restart the system If the problem is not resolved after restarting contact a service engineer Inform a service engineer of the error code Click OK to close the dialog box and then shut down the image capture computer see 2 2 E030100001 No calibration data Perform calibration in the QC Tool Click OK to close the dialog box and then calibrate the detector refer to 3 5 1 in the Setup Guide E030201002 Periodic noise detected in acquisition data The grid must be removed in calibration Click OK to close the dialog box Remove the grid from the detector and then calibrate the detector refer to 3 5 1 in the Setup Guide E030201003 The cooling unit has been attached or detached Processing was halted Click OK to close the dialog box and retry the examination If this error occurs again inform a service engineer of the error code E030201005 E030201006 Generator is disconnected Enable the generator connection with Connect GEN on the system setup screen Restart the system if the gene
122. ox up to 64 characters Preset descriptions can be selected from the drop down list as well as by entering a description in the text boxes modified NOTE Grayed out information in the Edit Study Information dialog box cannot be NOTE Other study information items such as Requesting Physician and Study Instance UID can be configured to be shown in this dialog and modified in this step For details refer to 2 4 1 in the Setup Guide NOTE Frequently used descriptions for some study information items can be preset For details refer to 2 4 2 in the Setup Guide 3 Preparing for Examinations To protect the stored images To maintain a certain amount of free space in the local storage directory of the image capture computer stored images except for those being reviewed on the EXAM gt Examination or PAST gt View screen will automatically be deleted on a study basis beginning with the oldest one as the amount of data exceedingly increases To prevent images from being deleted select the Protect Image option To cancel clear the option 3 End modification Click OK 3 1 4 Changing a workspace If necessary the ordered workspace can be changed before examinations When two or more detectors are connected to the system detectors can be switched by changing the workspace Thumbnail Protocol The selected study order is highlighted ba 20 Aesults t Emergency Start Exam i aeaee 49 3 Preparing
123. pear The EXAM gt Manual screen may appear instead of the EXAM gt Worklist screen In such a case click the EXAM gt Worklist tab To sort the listed study orders Click a sort item in the column header The current order is indicated by ascending or Fj descending in the column To switch between ascending and descending sort order click the same item again To arrange the order of the column headers Drag an item and drop it in the target position Dragging the column border also adjusts the width of the column NOTE The items displayed in the column head can be selected in the system setup screen For details refer to 2 4 1 in the Setup Guide HDD free space icon To get a good performance of the Software during an examination check the free HDD space on a regular basis using this icon If the icon color changes from white to yellow delete unnecessary studies in the image capture computer If the free space decreases further the color changes to red Free space er Used space HOD NOTE Past study data deletion that starts automatically in the background may affect the Software performance See 5 3 for details on study deletion and also see step 2 in 3 1 3 on image protection 7 Narrow down the acquired list items to efficiently select target study orders if necessary Click to shrink and expand the pane Title boxes and their keyword a boxes a n e femme Study Status C
124. r s Manual E020201004 Unexpected error has occurred Gamma adjustment is not available Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software See 2 2 Then perform gamma adjustment refer to 2 3 2 in the Setup Guide If this error occurs again inform a service engineer of the error code E020201005 Failed to connect to the barcode reader Check that the barcode reader cable is connected properly and restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and check that the barcode reader is connected properly Then restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code E020201006 Cannot start specified examination Return to the Exam screen and retry the failed examination Click OK to close the dialog box and retry the previous operation on the EXAM gt Worklist screen or the EXAM gt Manual screen If this error occurs again inform a service engineer of the error code E020201007 A detector communication error occurred Please retake this protocol If the problem is not resolved contact a service engineer Click OK to close the dialog box and retry the examination for the same protocol If this err
125. r Exposure I 114 146 4 Years A fay Tut Current te et 0010 amp 0000010 i Stitch 2images ef WS CXDI50G H m Remain A 2 image s reaper Pres ewe Ready thumbnail highlighted in green NOTE Ifthe protocol does not automatically enter ready mode click to select the target protocol NOTE Depending on the X ray generator the number of partial images less than the preset value can be specified from the X ray generator side 4 Arrange the patient in the correct posture Arrange the patient so that the stitch markers are positioned appropriately within the irradiated field and instruct the patient not to move during the examination 170 8 Stitching images Long length imaging Perform exposure Press and release the exposure switch on the X ray generator The Ready indicator changes to Capturing and then to Rane in the system status bar After processing is complete a preview image appears in the image view pane and the next ready thumbnail is automatically highlighted SA poste NOTE The number of partial images required for a long length image is preset for switch es each stitch type protocol within a range of two to four exam past o SS E di ser pis nre A 0000010 i Stitch 2images g z 1 WS CXDISOG kitre a Retake Stitched image X49 Raiost will appear here F439 Tool 2 Ai Exam Suspend Exam Re
126. ransfer the preview thumbnails on the transferred protocols turn sepia in color NOTE The transferred images cannot be modified through the post processing To check the current output settings before finishing an examination Proceed to 7 1 1 Checking and changing the image transfer settings To enter freely information on examination See 4 9 When a detector enters sleep mode Depending on the detector type when a detector is left unused for a certain period of time the Not Rea annot be used sleep mode indicator appears in the system status bar and all protocol al are gt deselected To restart the examination select the protocols again NOTE To reduce power consumption the Ready status shown in the system status bar can be manually canceled Click Unselect 6 Finish the examination Click End Exam The image data will be transferred to a preset destination such as a printer refer to 2 6 in the Setup Guide During data transfer the data transfer indicator or E4 flashes see 1 4 1 After finishing an examination captured images can be reviewed on PAST gt View screen see 5 2 4 Conducting Examinations When the image arrangement screen appears Proceed to 7 1 2 Arranging and printing images automatically NOTE Users can finish the examination even if incomplete protocols remain 1 4 Conducting Examinations 4 2 Replacing an incomplete protocol with another protocol
127. rator connection has failed If the problem is not resolved after restarting contact a service engineer Click Connect GEN in the system setup screen refer to 2 1 1 in the Setup Guide If the connection with the X ray generator device continues to be disabled restart the image capture computer and the Software see 2 2 187 9 Troubleshooting Remedies E030201007 Failed to enter the image capture ready condition Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box Exit the QC Tool mode and restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code E030201008 Detector cannot be used because the battery has lost its charge Processing was halted Click OK to close the dialog box and suspend the examination see 4 6 Then charge the battery of the wireless detector and restart the suspended study order For the wireless detector refer to the Digital Radiography CXDI series User s Manual E030201009 The detector temperature has reached dangerous levels Processing was halted Suspend the examination see 4 6 and wait until the temperature decreases Then restart the suspended study order E030201010 No battery is attached to the detector Attach the battery Click OK to close the dialog box and attach the battery pack to the detector
128. reen automatically appears so that the created long length image can be checked see step 7 in 8 2 If partial image alignment failed realign the images manually Cropping and rotating features are available for perfect alignment Maximum meei P EI Zoom in Zoom out E Fit in pane Preview pane S Click to cancel the An example of failed previous operation alignment two pairs of markers should fully overlap Click to close the Stitch Screen without saving changes for the long length image OK Stitch Screen 1 Check the automatically aligned images Check that the two pairs of stitch markers on the overlapped images are fully matched To scale the image in the preview pane Click EUSA or EI and then click on the area where close observation is required Click cy and then click on the preview pane to zoom out Click ED to fit the image to the preview pane 2 Select a target partial image for an arrangement Click a target partial image Small squares appear at the image corners 175 8 Stitching images Long length imaging To select two or more partial images Shift click partial images one by one To clear a selected image shift click it again To clear all image selection Click on a blank space in the preview pane EB Cropping Free rotation Rotate clockwise Selected partial image Rotate counterclockwise Click to cancel t
129. rier EXAM gt Examination screen Conducting Examinations see chapter 4 Reviewing Images see chapter 5 Image Processing wi Anatomical Part LUT Enhancement y Y Dynamic Range Adjustment T 1 Printing and y Yy y Noise Reduction transferring images Grid Suppression PAST gt View screen Reviewing images on the PAST gt View screen see 5 2 Sharpness Adjustment Peripheral Mask bmaqeProc Measurement 7 2 Using the Image Processing panel Levels 2 and 3 gt f Shutting down the Software see 2 2 Image arrangement screen 7 1 2 Arranging and printing images automatically 140 141 7 Other Functions 7 1 Printing and transferring images The Software can be configured to automatically print or transfer images to PACS storage media and other destination directories after finishing examinations on the EXAM gt Examination screen For details on configuring the destinations refer to 2 6 1 2 6 2 and 2 6 5 in the Setup Guide Users can manually perform additional image transfer as required NOTE Images cannot be printed from the PAST gt Past List screen EB Output setting B aana TT Print Output option o Outputsettings a utput Settings PAST gt View screen Printer screen A Print Output PAST gt Past List M Print Output Y M Show the image arrangement screen screen MI Show the image arrangement
130. ring for Examinations 3 3 30 Modifying study information See steps 3 through 5 in 3 3 1 for details on operation 3 3 4 Changing a workspace See 3 1 4 for details on operation 63 3 Preparing for Examinations 3 4 Creating emergency study orders Emergency button In the case of an emergency examinations can immediately be started for quick operation However patient information details are left unspecified If necessary the patient information acquired from the HIS RIS database can be bound with the resulting images at or after the examination Be sure to use the Emergency button only for an emergency examination If not heeded the resulting patient mix up and a misdiagnosis may cause harm to the patient 7 Create a study order Click Emergency A new study order emergency study is created in the study information pane with a temporary patient name and a patient ID automatically entered by the Software T ER J0 c ee Emergency EXAM gt Worklist or EXAM gt Manual screen name ALANSA LS CGC Temporary patient Patient ID 2 Select the target protocols See step 2 in 3 1 5 for details on operation 3 Preparing for Examinations 3 Start the examination Proceed to 4 Conducting Examinations To bind study information acquired from the HIS RIS database to the resulting images Proceed to 4 8 Binding study information with the
131. rklist screen System setup screen Selecting study orders Worklist tab System setup screen refer to chapter 2 Start screen see 3 1 in the Setup Guide 2 1 Starting the Software 2 2 Shutting down the Software Leis Crone WEWE Pitt a 19 kenis 2 3 Conducting offline examinations Inspecting maintaining the system NOTE Regular inspection and maintenance of a medical imaging system is required to assure the strict image quality For details on operation refer to 3 5 in the Setup Guide The frequency of adjustment work required using the QC Tool such as calibration will differ depending on the detector type For details refer to the Digital Radiography CXDI series User s Manual 28 29 2 Starting and Shutting Down the Software 2 1 Starting the Software 7 Turn the power box and the image capture computer on The start screen appears For details on operation refer to the hardware operation manual 2 Log in to the Software Select the user name type the password and then click Log In Click to shut down the Software User Name selector Log In Password text box Start screen NOTE Another start option that does not require user authentication is also available For details consult your service engineer 30 2 Starting and Shutting Down the Software To modify the user authentication settings The system setup screen allows users to change add or delete user names and c
132. rsed Contact a service engineer Click OK to close the dialog box and inform a service engineer of the error code FO040400003 Failed to acquire the system settings Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code FO040700100 The system memory settings are invalid Check the setting information Inform a service engineer of the error code Click OK to close the dialog box and then shut down the image capture computer see 2 2 184 9 Troubleshooting Remedies FO50502009 A detector communication error occurred Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code 185 9 Troubleshooting Remedies 9 1 2 Error list E020201003 Detector cannot be used because the battery has lost its charge Charge the detector battery Click OK to close the dialog box and charge the battery of the wireless detector Or if the optional wired connection is available switch to the connection For the wireless detector refer to the Digital Radiography CXDI series Use
133. s can be specified 2208x2688px Cropping Area Preset For radiographic images resumes default custom cropping area specified in the Common Cropping Area options in the System Settings tab refer to 2 3 1 in the Setup Guide or Cropping Area options in the Protocol Workspace Settings screen refer to 3 4 1 in the Setup Guide Detected Irradiated Field Crops only the irradiated field Effective Area Crops the effective area of the detector NOTE Custom area buttons other than 2208x2688px can be preset For details refer to 2 3 3 in the Setup Guide NOTE When users compare images on the monitor display the following should be observed As the size of Effective Area Detected Irradiated Field varies depending on the detector the magnification may change among images that are captured using different detectors when images are displayed after clicking a NOTE 2208x2688px and are not available for partial images captured by long length imaging and 2208x2688px and are not available for combined long length images as well For details see chapter 8 3 Set the area and exit cropping mode Click OK or B 6 Post Processing Images To mask outside the specified area Click El Only when masking is enabled for the image see 6 1 8 is available 6 1 8 Masking the peripheral area 1 The area outside a specified polygonal area can be masked see also 7 2 9 on images NOTE Unlike its gray appeara
134. s operation If this error occurs again show Additional Information to check the Error Code number detector error code to be shown and then inform a service engineer of the error code E040100054 The detector issued a fatal error Restart the system If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then restart the image capture computer and the Software See 2 2 However users can continue examinations without restarting by switching to another available detector If this error occurs again inform a service engineer of the error code E040100056 Generator is disconnected Enable the generator connection with Connect GEN on the system setup screen Restart the system if the generator connection has failed If the problem is not resolved after restarting contact a service engineer Click OK to close the dialog box and then click Connect GEN refer to 2 1 1 in the Setup Guide If the generator cannot be connected restart the image capture computer and the Software see 2 2 If this error occurs again inform a service engineer of the error code E040500003 Exceeded the maximum number of the study order acquisitions If you want to change the number of maximum study order acquisitions contact a service engineer Click OK to close the dialog box When the target study orders have been acquired start the examination Otherwise acqu
135. screen arrangement screen Film Destination Printe Film Destination printe before printing option I4INXI7IN Portrait Printer havam Portrait Printer 14INX17IN Landscape Printer1 14INX17IN Landscape Printerl 11INX14IN Portrait Printer1 11INX14IN Landscape Printer1 LINKJAIN Lands F 11NX14IN Landscape Printeri X Printer options lt TT gt Printer options Kil IE Storage _11INX14IN Portrait Printer1 i Storage _ Storage Serverl _ Storage Serverl Storage J Storage 2 Disk Storage Disk Storage option EA DiskStorage1 Save to System Oo amp Storage options Disk Storage DiskStorage1 Send Exam Send Image Click to cancel the M EE ooo TE settings Output Settings dialog box For PAST screen For EXAM screen Not available in the PAST gt Past List screen 142 7 1 1 2 7 Other Functions Target images for printing or data transfer The range of images to be printed or transferred will vary depending on conditions When starting operations in the EXAM gt Examination screen images in the current Exam will be printed or transferred When starting operations in the PAST gt Past List screen images in the selected Exam will be printed or transferred When starting operations in the PAST gt View screen see 7 1 4 either the current image or images in the current Exam will be printed or transferred Checking an
136. se scoliosis or knee osteoarthritis genu varum and genu valgum and to measure the Cobb angle or the angle that the upper and lower legs make The Software automatically aligns captured partial images to stitch and generate a long length image while fine adjustments can be made using the manual controls As an example a diagnosis of scoliosis is used in the following explanations NOTE The long length imaging feature accommodates only X ray generators whose X ray tubes rotate or tilt for serial radiography If the detector and the X ray tube move along parallel paths during an examination the quality of the created image may deteriorate resulting in the necessity of an additional examination NOTE Be sure to capture images from top to bottom or bottom to top keeping the same direction during an examination with each image in portrait orientation This examination can be performed for a patient in the recumbent or upright position NOTE Be sure to use 3 to 5 mm diameter small metal balls as stitching markers Markers other than the specified ones cannot be detected in long length imaging Stitch type protocol A protocol in which long length images can be generated by stitching captured partial images Up to four partial images can be stitched for each examination 8 2 Capturing and stitching images 168 A review of chapters 3 and 4 for details on DX protocol selection and examination procedures is recommended to better unders
137. segments An angle object with indicators for the measured angles both interior and exterior appears 131 6 Post Processing Images 3 Perform other angle measurements Repeat steps 1 and 2 To change the angle and position of an angle object Click on the angle object so that handles appear at the angle and the two endpoints of the object Drag a line to move it or drag either handle to change the angle To delete an angle object Click on the angle object so that handles appear at the angle and the two endpoints of the object and then click Delete 4 Exit measurement mode Click Measurement 6 3 3 Measuring the Cobb angle The Cobb angle is used to evaluate the curvature of the spine in a diagnosis of scoliosis For long length images that capture the entire spine and or lower extremities see chapter 8 exam Past Fo Worklist E Mariual Handles KWP eS infa Michael Taylor fe ime Dec Dob 1 14 1548 64 Yoars D P0 F T A 000010 7 Teh traps ih l E Measured Cobb angle Click to show and hide all line angle objects Delete C Click to show and Correction of Magnification Correct hide the scale at the soD mm SID _ mm bottom of the image view pane ImageProc Measurement Annotation Measurement 132 6 Post Processing Images NOTE The measurement unit and the scale shown at the bottom of the image view pane can be selec
138. ser name in the start screen to log in again 32 2 Starting and Shutting Down the Software 2 Show the Shutdown Confirmation Dialog Box Shutdown Confirmation Dialog Box Transfer All Data Transfer All Data option Latest backup date time 3 21 2012 12 42 PM ks Shutdown Backup Database option Restart Options Click to cancel shutdown and close the Shutdown Confirmation Dialog Confirmation Dialog Box Box To complete all image data transfer before exiting the Software Select the Transfer All Data option To back up the Software database completely before exiting the Software Select the Backup Database option To exit the Software without data transfer Clear both the Transfer All Data and Backup Database options i oean 33 2 Starting and Shutting Down the Software Exit the Software and shut down the image capture computer Click Shutdown in the Shutdown Confirmation Dialog Box Do not turn the image capture computer off before it automatically shuts down cee Doing so may result in damage to the hardware and or destruction of data To restart the Software without shutting down the image capture computer Click Restart Options and then click CXDI Restart in the recovery mode screen that appears CXDI Restart PC Sleep NS PC Hibernate n n Shutdown Recovery mode screen To put the image capture computer to sleep mode Click PC Sleep in t
139. setup can also be confirmed in the SC column in the same list For details on the storage commitment refer to 2 6 1 in the Setup Guide To narrow down the list items Enter any narrowing conditions in the Search For Study List pane Click to shrink or Target object Title boxes and their keyword expand the pane option boxes search For Study List en arget object _ Today Yesterday Recent week Recent month All Exam a ca Refresh Study Date option Click to clear the conditions for the keyword boxes and Study Date option Target object Select a period where the target examination was conducted from among Today Yesterday Recent week Recent month and All Exam Three of the following information titles can be selected for the narrowing conditions Patient ID Name ACC Study Description Protocol Name Series Description Body Part and View Position Select an option in each title box and then enter any keyword in its text box Note that these three keywords are used as AND search conditions NOTE Only when All Exam is selected for the Target object option during Local DB search see 5 3 Refresh appears In such cases click Refresh to start search after entering necessary keywords in the text boxes NOTE The information titles that can be selected for the narrowing conditions are those currently displayed in the column header For details on the column header settings refer
140. sician Th a Institution Name i re ee WS CXDI50G sa ll Edit Exam re ga Edit Exam Study information pane Detailed study information 2 Show the detailed information Click iva in the patient information pane or ira on the target study order To hide the detailed information click it again 46 3 Preparing for Examinations 3 1 3 Modifying study information If necessary the ordered study information can be modified before examination Linda Maller Dob i L987 Click to hide or show the protocols in the study order MATII TEADE AA POF Early Miiri The selected study order is highlighted O Emergency Start Exam e 47 3 Preparing for Examinations 48 7 Show the Edit Study Information dialog box Select the target study order in the Study List and then click jj on the target study in the study information pane and then click Edit Edit A 0000007 ACC 0000007 Referring Physician Charles Scott Study Description Reading Physician Institution Name oe S a E Study information pane Edit Study Information Referring Physician Study Description Reading Physician Institution Name Cancel Modify the study information Referring Physician Study Description Reading Physician Institution Name text box Protect Image option Click to cancel the operation OK Modify information in the Study Description text b
141. ssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mna 7 1 1 Checking and changing the image transfer settings cs scsssecensecnseeessenseenseeeseeonseees 7 1 2 Arranging and printing images automatically ccscesceeseeeeeeseeeeesenseeseesseesenseseessenseneenees 7 1 3 Arranging and printing IMAGES manually sssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn mnnn 7 1 4 Manually printing images in the PAST gt View SCreen c scssseessesseenseensennsenseeesennees 7 1 5 Manually transferring images to a storage server or storage media in the PAST gt View SCrEGIY asoini iaaeao aaa aaa ees Westen sees ences 7 2 Using the Image Processing panel Levels 2 and 3 cssscenseessenssenseenseenees 12 1 Switching ACCESS levels atsiri a a a a 7 2 2 Automatically processing images by specific anatomical part Anatomical Part control crescia aaa a a aN Aaa 7 2 3 Adjusting the overall image tone LUT control c ccceeeeseeesecnseenseessonseeseeensensensesenenneess 7 2 4 Enhancing contrast for anatomical part shape definition Enhancement control 7 2 5 Expanding or narrowing the dynamic range Dynamic Range Adjustment control 7 2 6 Reducing noise in images Noise Reduction control cesscenseensecenscenseenseeenseenseonseens 7 2 7 Reducing grid lines Grid Suppression control cceceeeeeeseeneeenecensenseenseeseonsenneeeseensenseses 7 2 8 Adjusting
142. sure type 70 F Fatal error 182 List 183 Fit 116 Flip 114 G Grid Suppression 162 H HDD free space 43 High resolution mode 116 HIS Study order 42 Histogram 126 ID Patient information 59 Refresh Option 45 Image Reprocessing 80 Image processing Level 1 126 Levels 2 and 3 154 Incomplete protocol Reprocessing 83 Restarting 85 Input New Annotation 137 L Laterality marker 117 Login 30 Logout 32 Long length imaging 168 LUT control 156 LUT curve 126 129 Curve shape 156 M Manual 58 Mask 123 Peripheral Mask 164 Measure angle 131 Measure Cobb angle 132 Measure distance 129 Measure height difference 134 Measurement 129 Modality 45 Multi view 97 Multiple study selection 107 N Name Patient information 59 Refresh Option 45 Searching 44 99 Negative and positive 114 Noise Reduction 161 O Off Line On Line 36 Output setting 142 Index P Panning 115 PAST 13 98 Patient ID Searching 44 99 Patient information Checking 46 Modifying 62 Registering 58 Sorting 59 Peripheral device 37 Peripheral Mask 164 Pixel to pixel display mode 116 Posture Protocol 73 Workspace 50 Power box Before starting system 30 Not Ready 73 Preview 124 Preview annotation 71 96 Preview image 74 Preview thumbnail 74 Printable area adjustment 147 Protect image 49 Protocol 42 Configuring 51 Replacing incomplete protocol 78 R Rebind 86 Recovery mode 34 Recovery mode screen 35 Refresh Option 44
143. t blink add a new page before dragging the images 6 Continue arrangement Repeat steps 3 through 5 150 7 Other Functions To automatically arrange the rest of the images Click Auto Layout and then click OK in the confirmation dialog box that appears Print the arranged images Click OK 7 1 4 Manually printing images in the PAST gt View screen Show the Output Settings dialog box Click EM Enable the preset printer Select the Print Output option When users need to check the image arrangement before printing select the Show the image arrangement screen before printing option To disable the printer clear the Print Output option To save the changes made in the Output Settings dialog box Click Save to System The changes will be reflected in the default setting that can be configured in the Connection tab in the system setup screen and also applied to subsequent printing and transfer operations Start printing Click Send Image to print the current image or click Send Exam to print the images in the current Exam Confirm or modify the image arrangement For details see 7 1 2 and 7 1 3 151 7 Other Functions 7 1 5 Manually transferring images to a storage server or storage media in the PAST gt View screen In the system setup screen users can specify storage media and an external HDD in the image capture computer where the Software itself is installed as well as a stora
144. tails on the Protect Image option see step 2 in 3 1 3 Also refer to 2 4 1 in the Setup Guide for the Column Headers setting To select multiple studies keyboard and mouse operation Click one study and then shift click the second one The two clicked studies and all studies between them are selected Control click enables another multiple selection All the control clicked studies are selected To select multiple studies touch screen display operation Touch Enable additional selection and then touch the target studies one by one All touched studies are selected To select all studies at the same time Click Select All Studies To clear the selection Click a highlighted study to clear other selections Control click a highlighted study to clear the selection Click Select All Studies twice to clear all selections 107 5 Reviewing Images 108 To specify the target data volume to be deleted for the Local DB option only Enter a value in the reduction target text box If the amount of deleted data does not reach the target amount an alert will appear NOTE The reduction target text box and Delete are available only when the user who has the Security Administrations privilege logs in to the Software For details consult your service engineer Delete the target studies Click Delete and then click OK in the Warning dialog box that appears a Warning OK to delete the Study _ Delete uncommi
145. tand the long length imaging workflow using the stitch type protocol When the system is not linked to a RIS HIS network be sure to manually create a necessary study order See 3 3 to start an examination NOTE This section explains an examination method that uses stitch markers for image alignment For details refer to 2 3 1 in the Setup Guide 8 Stitching images Long length imaging 7 Select a target study order that includes a stitch type protocol Michael Taylor Dob LIVIE MERS A Auodessicen Ha b m Shudty Stated E All Eam Mew Lor Peni Exar Meina Exien Stitch type protocol Edit Exam er Start Exam EXAM gt Worklist screen To add a stitch type protocol to the current study order Click Edit Exam on the EXAM gt Worklist screen to show the Edit Exam screen and then click the target stitch type protocol For details on the Edit Exam screen see 3 1 5 through 3 2 2 Stitch type protocols Stitch d j Select by Workspace ET Cancel Start Exam iiey Edit Exam screen i aeaee 169 8 Stitching images Long length imaging 2 Start the examination Click Start Exam 3 Select the target stitch type protocol If necessary click the incomplete target protocol and confirm that the indicator changes to Ready in the system status bar and that a ready thumbnail appears in the target protocol System status bar E KW ean Sine ee Taylo
146. target layout template in the template pallet that appears and then click Next Add Page Template pallet Next ee Click to cancel selection Template dialog box 149 7 Other Functions 4 Select the film size and scaling options Select the following options and click OK Size Click on the drop down arrow and select an option from the list The next Destination Printer option will be selected automatically depending on the configuration made in the Printer tab refer to 2 6 2 in the Setup Guide Fit Style Select a scaling option from among Fit The image is shrunk or enlarged to fit the image box keeping its aspect ratio and Fixed Ratio The image is placed at the center of the image box at the specified zoom ratio Zoom Ratio When Fixed Ratio is selected for the Fit Style option above it is necessary to specify the ratio in When pages have already been created the newly created page is added after the last page Size option ra gt Fit Style option Zoom Ratio 2 Zoom Ratio option Click to return to the G COS OK template dialog box Click to cancel creating a new page To insert a page before the current page Click Insert Page and then click on a layout template on the list that appears 5 Arrange the images Drag an image from the Image List to a destination image box in the arrangement preview pane NOTE When all images on the Image List do no
147. ted on the system setup screen For details refer to 2 4 1 in the Setup Guide Enable Cobb angle mode Click iJ The on screen Help for measurement location settings is provided at the top of the image view pane NOTE Once Cobb angle mode is enabled operations other than step 2 below are disabled Be sure to complete operations through step 2 Measure the Cobb angle of a specific part Click six points on the image view pane in the order shown in the figure below to form a Cobb angle A Cobb angle object with indicators for the measured angles both interior and exterior appears 1 2 The entire edge of the segment identifying the inferior surface of the lower vertebra 3 4 The entire edge of the segment identifying the superior surface of the upper vertebra 5 The center point of Cobb angle 6 A set point to determine the arc size of Cobb angle indication Perform other Cobb angle measurements Repeat steps 1 and 2 To change the angle and position of a Cobb angle object Click on the Cobb angle object so that handles appear at the angle and the four end points of the object Drag a line to move it or drag either handle to change the Cobb angle To delete a Cobb angle object Click on the Cobb angle object so that handles appear at the angle and the four end points of the object and then click Delete Exit measurement mode Click Measurement 133 6 Post Processing Images 6 3 4 Measuring t
148. ter tab refer to 2 6 2 in the Setup Guide Fit Style Select a scaling option from among Fit the image is shrunk or enlarged to fit the image box keeping its aspect ratio and Fixed Ratio the image is placed at the center of the image box at the specified zoom ratio Zoom Ratio When Fixed Ratio is selected for the Fit Style option above it is necessary to specify the ratio in NOTE Settings for this feature can be preset for each protocol Refer to Protocol Workspace Settings in step 2 under 3 4 1 in the Setup Guide for details on the option settings 146 7 Other Functions To check and adjust the printable area When an image is larger than the printable area the area is automatically aligned to the center top or bottom of the image and the outside the area cannot be printed Click Printable area adjustment and check the area shown in the orange rectangle Adjust the position using the arrow buttons and then click OK to set the adjustment NOTE The printable area can be preset for each protocol Refer to Protocol Workspace Settings in step 2 under 3 4 1 in the Setup Guide for details on position settings Printable area adjustment Printable area adjustment Printable area OK NOTE The scale of which magnification is corrected See 6 3 1 can be embedded at the bottom of an image For details on the settings refer to step 5 under 2 6 5 in the Setup Guide NOTE Even if the size of
149. the cropping area 120 6 Post Processing Images 2208x2688px cropping area preset button Select Arrow buttons Handles Handle and resize pointer To specify a new area Click Renewed so that it is highlighted and the pointer changes to 7 crop pointer Click two diagonally opposite points or drag the pointer on the image to specify a rectangular area To adjust the specified area Point any handle to change the pointer to S resize pointer and then drag the handle 121 6 Post Processing Images 122 To move the specified area Click Renewed so that the highlighting is cleared hover on the cropping area to change the pointer to p move pointer and then drag the area To finely adjust the position click the arrow buttons hl ka i To rotate the specified area Click to rotate the area clockwise 90 degrees NOTE When Custom Area is selected for the Cropping Area option in Protocol Workspace Settings refer to 3 4 1 in the Setup Guide when is clicked the setting for the Alignment option will be applied to the cropping area To cancel the changes and resume to the area specified in Protocol Workspace Settings Click Reset For details refer to 2 3 1 and 3 4 1 in the Setup Guide To specify an area with a single click of a button Click one of the following buttons to cancel the selection and specify the preset area Three preset area
150. the dialog box and then contact the system administrator The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E040505017 An error occurred in DICOM communication Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box Click Refresh to acquire the study orders see 3 1 1 The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code 193 9 Troubleshooting Remedies E040505018 A response error occurred in DICOM communication Check the destination modality or server etc Click OK to close the dialog box and then contact the system administrator The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E04050501B An error occurred in DICOM communication Try again If the problem is not resolved contact a service engineer Click OK to close the dialog box Click Refresh to acquire the study orders see 3 1 1 The problem may be resolved by checking the destination server or the DICOM conformance statement If this error occurs again inform a service engineer of the error code E04050501F An error occurr
151. the dialog box and then continue the operation 201 9 Troubleshooting Remedies W040500007 Characters which do not match the current character code are used in this data This character code will be properly changed automatically Check the setting information Click OK to close the dialog box Characters that do not match the current character code will be replaced with 2 Continue the operation when the replacement is acceptable To disable the replacement inform a service engineer of the error code W040500009 Failed to copy a tag to C STORE Check the tag information and the C STORE communication log If the problem is not resolved contact a service engineer Click OK to close the dialog box and check the original DICOM tag and the C STORE communication Then correct the original tag and retry the previous operation If this error occurs again inform a service engineer of the error code W04050000A Failed to copy tag to the DicomFile Check the original data If the problem is not resolved contact a service engineer Click OK to close the dialog box and then check the original DICOM tags of the DicomFile and the DICOM communication Correct the original tags If this error occurs again inform a service engineer of the error code W040505003 W04050500A W04050501C 04050501E An error occurred in DICOM communication Contact the system administrator The problem may be resolved by chec
152. the protocols can be moved up or down within a single study 52 3 Preparing for Examinations 3 2 Selecting protocols This Software provides a variety of useful protocol selection methods so that users can easily prepare for examinations and configure protocols 3 2 1 Searching for a protocol by a body part 7 Specify a target body part Click in the body part selector to highlight the target body part The protocols in the enabled lists are narrowed down into the focused body part NOTE Two or more parts can be selected eam me B Specified body part Click to clear all conditions including the Search options conditions in the body part selector Start Exam Edit Exam screen body part search mode To clear the body part conditions Click the highlighted body part again oaee 53 3 Preparing for Examinations 2 Specify detailed narrowing conditions lf necessary click Search Options and then click target condition buttons to highlight them in the Search Options panel Exposure Type Radiography and Stitch are available see 4 1 View Position Nine conditions are available Protocol Name Type part or the entire protocol name in the text box and click Search Search Options James Smith Select by Workspace Cancel Start Exam Radiography Exposure Type selector Stitch View Position selector Protocol Name text box Search Click to cle
153. ther protocol see 4 3 the duplicated protocol remains even if the original image is restored NOTE After the duplicated protocol is replaced with another protocol see 4 2 the duplicated protocol remains even if the original image is restored 5 Conduct an examination using the duplicated protocol See 4 1 for details on operation 4 5 Rejecting images Depending on the Software setup the images of complete protocols are generally transferred to PACS printers and other destinations for diagnosis and other purposes when End Exam is clicked The transfer feature can be disabled for unnecessary images resulting from failed exposure and other reasons 1 Select a failed image Click the target complete protocol in the study information pane 2 Reject the image Click Reject Clicking the button changes Reject to Restore See the figure in step 2 under 4 4 The selected preview thumbnail is crossed out To restore the rejected images Click the target complete protocol to restore and then click Restore 84 4 Conducting Examinations 4 6 Suspending an examination If necessary an examination that includes incomplete protocols can be suspended The incomplete protocols will remain in that examination and can be restarted later A suspended examination even if it was abnormally terminated can be restarted later 1 Suspend an examination currently being conducted Click Suspend Exam Listing functional
154. to List When the original annotations must be overwritten with the modified one click Place amp Apply 137 6 Post Processing Images To select deselect an annotation Click the target annotation on the image view pane An annotation highlighted with dashed orange border is selected and active Before performing other operation be sure to deselect an active annotation by dragging it to the same position Clicking an inactive annotation makes it active PAST B i Manual Gamination fay E Selected annotation Unselected annotation Click to undo the previous operation Enlarge Delete Annotation Reduce 3 Change the position of an annotation Click an annotation to select and then drag it to any position or click any point within the image view pane 4 Change the size of an annotation Click an annotation to select and then click Enlarge or Reduce repeatedly until the desired size is reached To delete an annotation Click an annotation to select and then click Delete 5 Continue to edit other annotations Repeat steps 2 through 4 6 Exit annotation mode Click Annotation 138 Other Functions 7 1 Printing and transferring images 7 2 Using the Image Processing panel Levels 2 and 3 This chapter explains how to arrange images and how to print or transfer images Advanced image processing features for administrative users are also explained Workflow D
155. to the Column Headers option under 2 4 1 in the Setup Guide Study Date Specify both or either the start and end date of the target period This option is enabled only when the Recent week Recent month or All Exam is selected for the Target Object option 99 5 Reviewing Images 5 2 1 Reviewing images saved in the image capture computer Images stored in the image capture computer can be reviewed 7 Select the volume containing the target study Select Local DB for the directory option 2 Select the target study Click to highlight a study The selected study is listed in the study information pane 3 Show the image Click Recall Exam The image appears in the image view pane in single view mode Past List Past List tab E Restart Exam Click to save changes for the current image Back To List Restart Save yal 7 Image s Back To List To perform post processing Proceed to 6 Post Processing Images 100 5 Reviewing Images To review other images Click Back To List and then follow steps 2 and 3 The Study List can also be displayed by clicking Past List tab View tab ee u TBA PAST gt Past List screen when an image is displayed in the PAST gt View screen NOTE The image of a study listed in the PAST gt Past List screen with fm indicated in the attribute icon column is being reviewed in the PAST gt View screen see NOTE in 5 2 3
156. tocol by a body pa rt ssnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn 53 3 2 2 Searching for a protocol by category ccsccesscesecescnsceseceseensensecensensecnseensenseonsecnsensensenseenes 56 3 3 Creating study orders Manual tab ccscssscnsceseenscnsenscensensenseonsensenseessenseeeens 58 3 3 1 Registering patient Study information ccesscessecesccessecnsecesecesecenseonseceseseaseonseneseseaseonees 58 3 3 2 Modifying patient information sicascnrcevcicaseuacinssenaecaninweveravewcaneacustuananeastasesneceunwesmeanenenaneuceneuanane 62 3 3 9 M difyi g Study INTOFIMAUON cvicsiinntexcsdinnsvenateucnstnecadnnssace icnceseausunnasuncuunatnwedposstsacuzeusnsuacdeusnies 63 3 3 4 Changing a WOIKSDAGC sarn a a a a 63 3 4 Creating emergency study orders Emergency button ccscessesseessenseesees 64 4 Conducting Examinations 4 1 Conducting radiographic CxaMiInatiONs ccesccescenscessnssenseessenssenseessenssensennees 70 4 2 Replacing an incomplete protocol with another protocol csscsssssssensensenees 78 4 3 Reprocessing an image of a complete protocol s sssssusunnnnnnnnnnnnnnnnnnnnnnnnnnnnnn n 80 4 4 Recapt nng IMAGES siioni aaa aae eae aa ALANEN EEES 83 4 5 Rejecting IMAG CS waceccctetcecsctescacccecetscscsensznadececensstacsssdesvecccecescusewennaveciesecaseseneesscegexs 84 4 6 Suspending an examination ssssssnssnnnunnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
157. tted study Select to delete studies during transfer Cancel ox Warning dialog box when the target capacity is not specified z S Warning OK to delete the specified volume Cancel OK Warning dialog box when the target capacity is specified 6 Post Processing Images 6 1 Using the toolbar Basic processing 6 2 Using the Image Processing panel Level 1 6 3 Using the Measurement panel 6 4 Using the Annotation panel This chapter explains how to modify captured images for more effective image interpretation during diagnosis Furthermore measurement results distance and angle including values units and line segments can be superimposed over images in the image view pane Workflow iat EXAM Examination screen Conducting Examinations see chapter 4 Reviewing Images see chapter 5 PAST gt View screen Reviewing images on the PAST gt View screen see 5 2 be PTs aia ge DN a r r i Shutting down the Software see 2 2 Image arrangement screen Arranging and printing images automatically see 7 1 2 110 xamination screen PAST gt View screen Image Processing ad 1 lt Brightness 6 2 1 Adjusting the brightness of bright region and dark region 6 2 2 Adjusting the overall brightness and contrast Measurement Comecton of Magnification 1414 2 mm SID 1000 mm 6 3 1 Measuring the distan
158. two types of toolbar have already been configured Click Tool 1 or Tool 2 NOTE Refer to 2 4 3 in the Setup Guide for details on toolbar customization 113 6 Post Processing Images 6 1 1 Rotating flipping images Images can be rotated and flipped 7 Rotate or flip the image Click to rotate the image clockwise 90 degrees EZ Click to rotate the image counterclockwise 90 degrees Click to flip the image vertically Click to flip the image horizontally NOTE Generally the preview image before clicking mn or S is a view from the X ray generator The image will be reversed after clicking one of these buttons 6 1 2 inverting a negative image to a positive image and vice versa Images can be inverted between negative and positive 1 Invert negative to positive and vice versa Click p To restore the original appearance click it again 114 6 Post Processing Images 6 1 3 Panning images To more easily view certain parts of an image click inside a cropped or magnified image and drag it to change the viewing boundaries NOTE The panning operation does not affect the images that are transferred to a storage server printer or other destination directories 7 Pan the image Click EJ and then drag the image to any position keeping the center of the image within the boundaries of the image view pane EXAM Wiorklist Patien ID PODIO KPa Patient Name lames Smith Pea i r
159. y Chinese characters contained in the acquired study order were replaced with Do not use the supplementary Chinese characters for study order creation on RIS database for this control software does not support these characters E040500008 A date entry before 1753 is included in the acquired Exam Check the date Check the data information and retry a data entry E04050000C Failed to read DICOMDIR file Check the target disk and retry reading Click OK to close the dialog box Check the removable disk and read the files again If this error occurs again files in the DICOMDIR directory may be corrupted Check the original files 9 Troubleshooting Remedies E04050000D A transmission error occurred Locate the failed study in the PAST gt Past List and retransmit the study Delete the data transfer error log from the Process Viewer refer to 3 3 in the Setup Guide and then resend the image from the PAST gt Past List screen see 7 1 5 EO4050000F Failed to read DICOM file Check the target disk and retry reading Click OK to close the dialog box Check that there is no problem in the storage media and the target file exists in the destination directory and then retry reading Errors also occur when the file format does not comply with DICOM standard or log in user has not been granted read access to the file E040500010 Failed to read DICOM file Check the target disk and retry readin
160. y order Click the target study order to highlight The selected study orders are listed in the study information pane Multi selection for ease of operation With a click of one study order in the list study orders with the same descriptions for five categories Patient ID Name Birth date Sex and Input data type will automatically be selected To deselect unwanted study orders from the selection click each order in turn Indicates either HIS RIS originated or manually created data 3 Start examination Proceed to 4 Conducting Examinations If a dialog box appears indicating that the protocol includes an unknown code value Consult your service engineer to create the protocol applicable to the unknown code value 45 3 Preparing for Examinations 3 1 2 Checking patient study information in detail 7 Select a study order Click a study order in the Study List Patient Detailed patient information pane information Linda Miller Linda Miller Patient name DoB 9 15 1987 DoB Age 24 Years AG ID POOOOO7 ID P000007 Sex Female Sex Female Date of birth L E Height 175 2 m Weight 60 kg Pregnancy status none not pregnant F pregnant a possibly pregnant Study title ACC A 0000007 a y etwi oo E Chest AP L wise e ae Click to modify study Referring Physician information if necessary PF Fine eee see 3 1 3 tudy Description Study order Reading Phy

Mark 1114CW Manual

Contents

Download Pdf Manuals

Related Search

Related Contents