Badu®Stream II
Contents
1. NOTE CHECK VALVES must be used on the discharge side of each pump Minimum 4 pipe between pump and BaduStream plumbing Figure 6 manifold BaduStream Triple Housing Installation 10 Concrete or Gunite Installation 1 Pre plumb BaduStream housings A B Install plumbing manifold or approximatelv 12 of 4 SCH 40 pipe to both suction and discharge fittings on the jet s housing NOTE If plumbing exceeds 30 between jet housing and pump increase pipe size to 6 Install a 6 x 4 reducing bushing as close to jet housing as possible Install air control PVC hose to hose socket insert fittings part 6 Use hose clamps to secure hose to insert fittings 2 Tape the jet housing keep concrete out of threaded inserts and out of the inside of the housing 3 Place jet housing into reinforced steel Jet housing location is very important A Locate air control hose connector part 6 at the top and center of jet housing Air control hose connectors must be vertical or the square cover will be uneven in appearance The center of the housing the nozzle should be 10 BELOW water level for maximum efficiency Front edge of jet housing should finish even with inside gunite wall Make sure a V shaped groove is scraped out around the housing approximately 11 2 deep to allow marcite to seal against the housing DO NOT disassemble jet nozzle from housing Recheck location of the jet housing when gunite is being appl2. Can the pump be placed below water level Yes However for best performance we recommend ordering pump for flooded suction Model 21 80 33G instead of self priming Model 21 80 33GS We recommend installing valves for ease of maintenance How far away can the air button function properly Amaximum of 50 ft Consult factory for distances over 50 ft Do need to install a motor starter No The pump has a built in thermal overload Should this be tied into my filter system No The swim jet system and the filter system should not be plumbed together as they each provide very specific functions Can I use with automated controls Yes It comes with the ability to tie into automated control systems or other switching devices 7 Product Specification 18 Part Qty Description NN NNa AN i 2 AD AD BR OOo A 9 2 9 2 oO Face Ring Nozzle Screw Tapping 5 5 x 19 Clamping Ring Nozzle adjustable flow Bushing Hose Connector 1 4 Housing Square Cover Screw M6 x 25 Screw M6 x 20 Screw M6 x 25 Screw M6 x 40 Screw M6 x 45 Seat Nozzle Spacer Ring 6 2 Spacer Ring 4 Gasket Clamping Ring Gasket Butterfly not shown Gasket Face Ring Holder w Hose Subassembly Hose Fitting 1 4 Hose 8x3 Hose Clamp 14 9 Holder Air Regulator Screw 1 4 20 x 1 1 2 Nut 1 4 20 Washer 1 4 Gasket 60 x 11 x 2 Part Qty Description 22 26 1 Subassembl
3. Water Velocity The maximum water velocity through the suction fitting or cover for any suction outlet must be 1 5 feet per second unless the outlet complies with the latest published edition of ANSI ASME A112 19 8 ANSI APSP 16 2011 the standard for Suction Fittings For Use in Swimming and Wading Pools Spas Hot Tubs and Whirlpool Bathtub Applications In any case do not exceed the suction fitting s maximum designed flow rate If 100 of the pump s flow comes from the main drain system the maximum water velocity in the pump suction hydraulic system must be six 6 feet per second or less even if one 1 main drain suction outlet is completely blocked The flow through the remaining main drain s must comply with the latest published edition of ANSI ASME A112 19 8 ANSI APSP 16 2011 the standard for Suction Fittings For Use in Swimming and Wading Pools Spas Hot Tubs and Whirlpool Bathtub Applications Testing and Certification Suction outlet covers must have been tested by a nationally recognized testing laboratory and found to comply with the latest published edition of ANSI ASME A112 19 8 ANSI APSP 16 2011 the standard for Suction Fittings For Use in Swimming and Wading Pools Spas Hot Tubs and Whirlpool Bathtub Applications WARNING Entrapment Prevention continued Fittings Fittings restrict flow for best efficiency use fewest possible fittings but at least two 2 suction outlets Avoid fittings that could cause
4. BaduStream in Concrete or Gunite Pool Liner and or Fiberglass Pool Installation 1 Using the clamping ring part 3 as a template drill holes in the pool wall for installation The center line of the clamping ring should be 10 below the surface of the water See Figure 8 Two additional holes need to be drilled at the 3 and 9 o clock positions for installation of the housing part 7 The four brass inserts in the clamping ring should be at the 2 4 8 and 10 o clock positions 12 Liner and or Fiberglass Pool Installation continued 2 Mount the housing part 7 and one gasket part 12 on the outside of the pool wall using two screws 14 x 1 part 27 Install the screws from the inside of the pool wall through the holes drilled at 3 and 9 o clock positions See Figure 10 amp 11 3 Install the clamping ring part 3 and the gasket part 12 on the inside of the pool wall using eight screws part 9 2 9 3 9 4 or 9 5 Screw lengths vary depending on the installation A Agood RTV silicone may be used with the gasket when mounting the jet housing but in most cases is not necessary Installer should decided whether or not the silicone is necessary B When installed properly the center of the housing part 7 will be 10 below the surface of the water and the hose connector 1 4 part 6 will be at the top center of the jet housing C When installing the BaduStream Cover part 8 Use a Phillips head screw
5. an air trap Pool cleaner suction fittings must conform to applicable International Association of Plumbing and Mechanical Officials IAPMO standards VGB Compliance The Virginia Graham Baker Pool Safety Act promotes the safe use of pools spas and hot tubs by imposing mandatory federal requirements for suction entrapments avoidance The Act which is being administered by the U S Consumer Product Safety Commission CPSC and became effective December 19 2008 is an extension of the ASME standard which regulates Safety Drain Covers Public Pool Drain Systems and SwimJet Combination Fittings The VGB Pool Safety Act compliance relies on the ANSI ASME A112 19 8 ANSI APSP 16 2011 code for proper testing and certification of the fittings The only addition is the requirement to exhibit VGB nomenclature on the actual fitting The Speck SwimJet Combination Fittings are certified by MET a Nationally Recognized Testing Laboratory NRTL to the ANSI ASME A112 19 8 ANSI APSP 16 2011 Standard bearing the VGB nomenclature and are compliant with the VGB Pool Safety Act As a condition of the listing all Speck Badu SwimJet Systems comply with the ANSI APSP 7 Standard for Suction and Entrapment Avoidance This standard is designed to avoid all five suction entrapment hazards hair entrapment limb entrapment body suction evisceration disembowelment and mechanical entrapment All Speck Badu SwimJet Systems are certified by MET to the ANSI ASME
6. or motor 2 General Description Badu Stream J The Badu SwimJet Systems from Speck Pumps are designed to be installed during the construction of your pool to create a water treadmill for anyone wanting a therapeutic and effective exercise The Badu SwimJet Systems can be installed in any type pool large or small from gunite to vinyl liner It has no protruding parts ensuring pool user s safety is very compact and installs at minimal cost The self contained flush mounted unit is a jet propulsion system that pumps water into the pool creating a current in excess of 5 700 gallons per minute from a single recessed jet housing Topping off the experience is the pulsating massage hose which can be attached to the jet nozzles for easy and convenient massage treatments for joints and muscles VOTE The massage hose is sold separately 3 Installation Information Preparation Guide 1 Upon receipt of the swimjet system check the cartons for damage Open the carton and check the pump F jet housing A and control box E for concealed damage such as cracks dents or a bent base If damage is found contact the shipper or distributor where the swimjet was purchased 2 Inspect the contents of the carton and verify that all parts are included All parts are manufactured of corrosion resistant material and combined in one single housing two or three single housings for multi jet systems which can be installed in pools of any size an
7. pump and pool Locate pump as close to the BaduStream as practical Use at least 4 pipe when distance between jet housing and pump is 30 ft or less and 6 for pipe runs longer than 30 ft The 4 HP self priming plastic pump has a single phase motor with thermal overload no motor starter required The 4 HP single phase motor draws a maximum of 19 4 amps 230V The unit requires a minimum circuit of 30 amps Install a 40 amp breaker to avoid nuisance tripping when pump is turned on and off frequently The starting current of the 4 HP motor can reach up to 6 times the running currents Three phase motor draws a maximum of 12 8 amps 230V and 6 4 amps 460V The 3 5 HP single phase motor draws 13 6 amps 230V Figure 2 BaduStream dimensional drawing Plumbing The BaduSteam assembly package contains all necessary parts for the installation of the unit into concrete gunite liner or fiberglass pools PLUMBING REQUIREMENTS BADUSTREAM Pump Distance Pipe Size Approx flow Pressure Three Jets 2 4 HP 10 to 30 ft 4 700 GPM 16 PSI up to 50 ft 6 700 GPM 16 PS
8. A112 19 8 ANSI APSP 16 2011 Standard and are defined in the standard paragraph 1 1 6 1 1 6 4 Swim Jet Combination Fittings All swim jet combination fittings that combine suction and discharge into one housing creating a high velocity high volume stream of water to swim jog or walk against as well as massage shall be considered Swim Jet Combination Fittings NOTE There are four types of Suction Fittings that are defined in the ANSI ASME A112 19 8 ANSI APSP 16 2011 Standard for Suction Fittings for use in Swimming Pools Wading Pools Spas and Hot Tubs They are Field Fabricated Outlets Venturi Outlets Swim Jet Combination Fittings and Submerged Suction Outlets WARNING Risk of Electrical Shock or Electrocution A WARNING This pool pump must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances Improper installation will create an electric hazard which could result in death or serious injury to pool users installers or others due to electrical shock and may also cause damage to property Always disconnect power to the pool pump at the circuit breaker before Hazardous voltage Ma A mid Can shock burn or servicing the pump Failure to do so could result in death or serious injurv to cause death serviceman pool users or others due to electric shock Disconnect power before working on pump
9. I Two Jets 4 HP 10 to 30 ft 4 380 GPM 14 PSI up to 50 ft 6 400 GPM 14 PSI One Jet 4 HP 10 to 30 ft 4 270 GPM 18 PSI up to 50 ft 4 260 GPM 18 PSI One Jet 3 HP 10 to 30 ft 3 200 GPM 12 PSI up to 50 ft 4 200 GPM 12 PSI Control Box eee Valves Optional Pressure Line 6 pipe will allow distances of well over 50 ft 7 b p 4 However control box needs to be within 50 ft for the c l T pneumatic on off button to function properlv 2 Allow 12 to prevent j l 2 cavitation of the pump LZ i l JA teen l re li j t m S IE Pump H 4 Air Regulator a Vertical mi l JU Discharge Line U N E E N Water Level r l LEJ H Check Value Optional N Horizontal Below Water Level Discharge Line E je e Vertical Suction Line NOTE valves are recommended wien pump E i ja Horizontal Suction Line max 30 feet with 4 pipe Figure 3 CAUTION All necessary screws and bolts included with the BaduStream are stainless steel ALL screw threads and threaded inserts are METRIC ONLY METRIC bolts and nuts may be used The two exceptions are the intake and delivery connections on the BaduStream and pump housing and the hardware for the air regulator assembly The intake and delivery connections on the pump model 21 80 are 4 Slip 3 Slip on pumps Model 72 The air regulator assembly hardware is US standard thread CAUTION The center of the housing the nozzle should be 10 BELOW water level for max
10. Installation Operating and Service Manual Badu Stream Counter Swimming Unit pans POOL PRODUCTS INCORPORATED Technical Support Manufactured by Speck Pumps Jacksonville Florida USA 2012 All Rights Reserved Address Hours Toll Free Phone Fax Web site Speck Pumps 8125 Bayberry Road Jacksonville FL 32256 USA 8 00 am to 5 00 p m EST Monday Friday 800 223 8538 904 739 2626 904 737 5261 www usa speck pumps com This document is subject to change without notice Date of Installation Installed By Serial Number For Service Call 2999999981 Rev 0412 ET 3 RT Table of Contents Important Safetv Instructions 4 Entrapment Prevention 5 VGB Compliance General Description 7 Installation Information 7 Preparation Guide 7 Planning 8 Dimensional Drawing 8 Plumbing Installation 9 Concrete or Gunite Installation 11 Liner and or Fiberglass Pool Installation 13 Removal of Liner 2 6 14 Pump and Control Box Installation 15 Operation 15 Service and Maintenance 15 Nozzle Adjustments 15 Winterizing 16 Trouble Shooting 17 General Troubleshooting Problems 17 Product Specification 18 Replacement Parts and Exploded View 18 Limited Warrantv 19 1 Important Safetv Instructions READ THIS MANUAL CAREFULLV BEFORE USING THIS PRODUCT READ AND FOLLOW ALL INSTRUCTIONSI Important Notice This manual contains important information ab
11. Parts required Quantity 2 4 x1 PVC Pipe Quantity 2 1 1 7 MPT x 1 2 1 Hose Adaptor Quantity 2 Female Adapter 1 1 2 Slip x 1 1 2 FPT 2 Turn off the jet pumps 3 Insert each jet adjustment tool into jet nozzle 4 Move each jet adjustment tool toward each other until each pipe touches at water level 5 Remove jet adjustment tool Hose Adapter 1 1 2 x 1 1 4 Tapered LIN PVC Coupling 1 1 2 PVC Pipe 1 1 2 x 4 Top View 10 Side View IP Perspective View Figure 13 BaduStream Nozzle Adjustment Winterizing In areas subject to freezing water temperatures you should protect your equipment We recommend you purchase a winter cover kit part 2308752006K This kit includes 1 winter plate 1 gasket and 4 screws Also you can protect your swimjet system as follows Drain pool until water level has dropped below the anti entrapment cover Then protect pump by removing drain plug and red filler plug or lid 16 6 Troubleshooting Frequently Asked Questions How is the current generated The pump generates up to 400 GPM coming out of two jet nozzles at 27 ft per second and 36 ft per second thru one nozzle creating a swim current in excess of 5000 GPM measured 6 ft from the jet What size pool
12. d shape See Figure 1 A Flush mounted Jet Housing D _ B Square Anti Entrapment Cover 81 4 x 81 4 undetectable pump suction Optional Round Cover B ever C Adjustable Water Flow Jet Nozzle c D Air Regulator adjusts amount of air bubbles A in water flow E Control Box with GFCI pneumatic button and 9 tubing Figure 1 F Speck 4 HP or 3 5 HP self priming plastic pump single phase with thermal overload no motor starter required Optional three phase motor and control box available NOTE Normal priming pump available for installation below water level G Optional Massage Hose with pulsator may be attached to jet nozzle Planning The BaduStream is normally incorporated into the original pool design However it can be added to any pool at a later date The BaduStream has no protruding parts ensuring the pool user s safety It is very compact and installs at minimal cost The BaduStream can be installed in any size pool We suggest a minimum pool size of 7 ft wide 14 ft long and 31 2 ft deep in order to swim Most swimmers prefer 16 ft in length or longer The extra length allows the swimmer to comfortably drift back and swim up stream The BaduStream is complete with jet housing 4 HP or 3 5 HP pump control box and optional massage hose The only additional requirement is the plumbing 4 pipe for 4 HP and 3 pipe for 3 5 HP units Consult local codes for minimum distance between
13. do need The BaduStream can be installed in any size pool However we recommend a minimum length of 14 and a minimum width of a 7 foot swimming lane What size plumbing is necessary How far away from the BaduStream can the pump be installed Use 4 plumbing up to 30 For runs longer that 30 use 6 plumbing The pump can be placed as close to the BaduStream as local codes will allow How many amps does the pump operate at 4 HP Maximum 19 4 amps 230 V 3 5 HP Maximum 13 6 amps 230 V What size breaker do l need You must use a 40 amp breaker for the 4 HP pump or 30 amp breaker for the 3 HP pump to avoid nuisance tripping Is the BaduStream approved Yes The BaduStream swim jet system is listed by MET and complies with UL standard 1563 Swimming Pool Equipment ASME standard ANSI ASME A112 19 8 ANSIVAPSP 16 2011 Standard for Swim Jet Combination Fittings and is VGB 2008 compliant Do the covers come in different colors Yes The round covers can be ordered in gray or black The square cover is only available in black or white Does the air regulator come in different colors Yes The air regulator can be ordered in black Does it matter if the housing is installed higher or lower than the manual states Yes the center of the jet must be 10 BELOW estimated water level for proper performance of unit Can the air regulator be placed elsewhere Yes as long as it is not continuously flooded with water
14. driver and tighten to 1 5 Nm or hand tight NOTE The square cover part 8 will have an uneven appearance if the housing is not installed properly 4 For the air regulator assembly one 1 2 hole must be provided preferably along the vertical axis approximately 4 or minimum 2 ABOVE the water line See Figure 10 amp 11 Using the air regulator assembly gasket part 21 mark and drill two 1 4 mounting holes See Figure 10 Use two flat head 1 4 20 machines screws part 18 and two 1 4 20 nuts part 19 to mount the air regulator NOTE The flat head on the inside of the pool wall and the nut on the outside of the pool wall 5 Keep all parts not being used now in original box Store in a safe place until needed For Liner Pools Only Install the jet housing and air regulator prior to installation or replacement of the pool liner For Steel Walled Pools An optional butterfly gasket part 12A maybe purchased to replace the two gaskets part 12 Increase the jet housing hole from 5 59 to 5 75 for installation See Figure 10 0 25 i i Air Regulator 4 o E 0 50 1 70 3 p 2 Minimum Water Level E l ot Water Level 4 Air Line 10 Pressure Housing e B Fitting 4 N Pipe 4 i Fitting 4 Suction 45 Elbow Liner amp Wall For Liner amp Fiberglass Pools Only Figure 10 Figure 11 Cutout Pool Wall for BaduStream housing BaduStream in Liner or Fib
15. erglass Pool Removal of Liner When replacing liner or removing liner for repairs remove 4 screws part 9 1 which hold the square cover part 8 to the jet housing Remove all screws part 9 2 amp 9 3 except the top two which hold the clamping ring part 3 and gasket part 12 to the jet housing Back out the two remaining screws approximately halfway and check for any movement of the jet housing from the wall NOTE If the two counter sunk screws part 27 which hold the jet housing to the wall were installed the jet housing should not move and the two remaining screws can be removed Remove one of the remaining two screws and slide the clamping ring part 3 to the side Replace all the screws before removing the last screw Remove or replace the liner Reverse the process to install liner NOTE When replacing the clamping ring and screws locate screw heads under liner make a small cut on the liner at the screw heads and push the liner over the screw head Pump and Control Box Installation CAUTION Before installing the Speck Pump read the entire pump owner s manual found in the pump box Consult local codes for minimum distance between pump and pool Locate pump as close to the pool as practical The air button works up to a maximum of 50 ft There is 50 ft of air tubing in the BaduStream box WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all ti
16. ied The force of the gunite may move the jet location To avoid stress on the jet housing we recommend that the BaduStream housing be encased with gunite and at least 2 to 3 inches of the plumbing stub out is covered with gunite NOTE Stress on the plumbing may crack the BaduStream housing 4 Air regulator installation should be approximately 4 or minimum 2 ABOVE the water level A To install the bottom parts of the sub assembly Air regulator holder and hose socket insert fitting connect to PVC hose Make sure air regulator holder face is tapped over to prevent gunite from entering holder Air regulator can be located in the tile line above water line or in the deck When tiling the pool adjust the air regulator holder to proper positioning 4 or minimum 2 ABOVE the water level Place and set with hydraulic cement Install air regulator flush with the inside pool wall Drill a 1 2 hole in the tile even with the center hole on the air regulator Then tile over the air regulator holder part 17 Note Be sure NOT to plug the center hole of the air regulator holder with thinset or the tile Install the air regulator sub assembly 1 Top Part Part 22 2 Bottom Part Part 23 3 Screw M10 x 80 Part 24 5 4 Hose Ring 16 x 30 x 80 Part 25 A 5 Gasket Air Control 42x 11x2 Partit 26 KE a flat head screw driver is required to tighten the screw to the holder Make sure the air regulator holder
17. imum efficiency The air regulator should be approximately 4 or minimum 2 ABOVE the water level See Figure 3 CAUTION When connecting the pressure line into the pressure connection on top of the 4 HP pump Model 21 80 first install a 6 15 cm riser See Figure 3 before installing an elbow and leading the pressure line downward to the pressure connection at the jet housing This will guarantee trouble free priming of the pump Not required for the 3 5 HP Model 72 CAUTION When using 6 pipe the suction line should run to a point directly under the pump and up to the water line in 6 and finish vertical and elbow into the pump in 4 to minimize priming time See Figure 3 CAUTION n areas with soft soil conditions or with frequent earth movement a flexible section of hose should be attached to the back of the jet housing to prevent housing breakage CAUTION Throughout the entire installation make sure the plumbing connected to the BaduStream housing is well supported Unsupported plumbing will crack the housing Plumbing continued BaduStream Single Housing Installation Figure 4 B a ad gi L Ln A i 7e A s e AN Pa k oe N KI a 2 U Uy f Zn N U ANA LY SIAC C ILA ar 44 QY Figure 5 e AO gt NOTE For Dual and Triple Jet Installation Increase the pipe size to 6 when jets are more than 30 ft from the pump Use 6 x 4 bushings after 4 manifold tees
18. injury or death minimizes risk of injury to users of pools spas and hot tubs Do not block suction Entrapment Protection The pump suction system must provide protection against the hazards of suction entrapment A DANGER l Suction Outlet Covers All suction outlets must have correctly installed screw fastened covers in place All suction outlet drain covers must be 41 maintained Drain covers must be listed certified to the latest published edition of ANSI ASME A112 19 8 ANSI APSP 16 2011 Thev must be replaced if cracked broken or missing Hazardous suction eel a niin Number of Suction Outlets Per Pump Provide atleast two 2 hydraulically injury or death balanced main drains with covers as suction for each circulating pump Do not block suction suction line The centers of the main drains suction outlets on any one 1 suction line must be at least three 3 feet apart center to center The system must be built to include at least two 2 suction outlets drains connected to the pump whenever the pump is running However if two 2 main drains run into a single suction line the single suction line may be equipped with a valve that will shut off both main drains from the pump The system shall be constructed such that it shall not allow for separate or independent shutoff or isolation of each drain More than one 1 pump can be connected to a single suction line as long as the requirements above are met
19. is free of l debris or the screw part 24 will not screw in Figure 7 properly Air Regulator Assembly 11 Concrete or Gunite Installation continued Note Make sure the gasket part 26 is on the back side of the bottom part part 23 against the tile This will keep the parts secure to the tile E Install the top part part 22 Snap the top part to the bottom part part 23 and turn clock wise until you hear it ratchet Turn clock wise to adjust the air 5 When installing the BaduStream Cover part 8 Use a Phillips head screw driver and tighten to 1 5 Nm or hand tight 6 Keep all parts not being used now in original box Store in a safe place until needed An extension ring is available upon request for an application that has special needs 6 The following is a list of all parts that ARE NOT USED IN A GUNITE INSTALLATION 1 Gasket Clamping Ring Part 12 2 Bolt s 20 x 1 1 2 Part 18 3 Nut 4 20 Part 19 4 Washer Part 20 5 Gasket 60 x 11 x 2 Part 21 6 Screw Jet Housing 14 X 1 Part 27 Air Regulator Air Regulator Tile i 2 Minimum i Water Leve 2 Minimum lee l Water Level Air Line Concrete Wall Nozzle Pressure Housing Fitting 4 Pipe Fitting 4 45 Elbow Suction Plaster Figure 8 Figure 9 Template for Installation in Gunite or Concrete Pools
20. ise reduces the flow The swivel nozzle s of the BaduStream can be positioned in various directions allowing swimmers to use various swim styles Optional Accessory The Badu Swim Mirror is a perfect addition to the BaduStream this portable mirror is designed to be the perfect tool to help swimmers stay in the swim lane Optional Accessory A pulsating massage hose can be attached to one of the nozzles to enjoy a massage as advised by your physician See Figure 1 Letter G Directions for use Consult your physician before using the massage hose To reduce the risk of injury do not permit children to use the massage hose with pulsator unless they are closely supervised at all times Close the air regulator Reduce the volume of water by turning the adjustable flow nozzle s clockwise Figure 12 Under certain conditions it is possible that the current Badu Swim Mirror drifts off to the left or to the right from the middle due to water bouncing off the back wall In the event that this interferes with your swimming action turn unit off for a few minutes and restart D Service and Maintenance Nozzle Adjustment When setting the nozzles for basic swimming it is recommended that you set the nozzles in such a way that each nozzle s intersects 4 feet away while at the same time breaks the surface 15 Nozzle Adjustment continued To help set the nozzles in a neutral position please follow these instructions 1
21. mes The wiring of the pool motor and control box should be done by a licensed electrician in accordance with local codes Be certain that the motor frame and control box are grounded Motor name plate has voltage phase amp draw and other motor information as well as wiring connection instructions BONDING As required by National Electrical Code Article 680 22 the pump motor must be electrically bonded to the pool structure reinforced bars etc by a solid copper conductor not smaller than No 8 AWG via the external copper bonding lug on the pump motor GROUNDING Permanently ground the pump motor and control box using a conductor of appropriate size Connect to the No 10 green headed ground screw provided inside the motor terminal box NOTE Do not connect to electric power supply until the unit is permanently grounded Section 8 concerns the electric motor and control box only since all other parts the pump the jet unit etc have complete and absolute separation from the pool water 4 Operation Operation Remove the red filler plug or strainer tank lid on the pump and fill the pump with water Replace the red filler plug or lid Push pneumatic button on For the first start up allow approximately 5 minutes for the pump to prime If the pump has not started priming after 5 minutes the amount of water in the pump was not sufficient Add more water Due to the large volume of air that can be present in the vertical portion of the suc
22. n hereunder shall be to replace or repair any defective BaduStream The manufacturer reserves the absolute right to determine whether any defective BaduStream should be replaced or repaired 5 Any customer who wishes to make a claim under this Limited Warranty shall notify Speck Pumps of such claim by telephone or by mail After the customer has been authorized to return the BaduStream the customer must return the BaduStream to Speck Pumps Any goods returned to Speck Pumps without prior authorization will be returned to the shipper unopened Speck Pumps shall not bear any costs or risks incurred in shipping a defective BaduStream to Speck Pumps or in shipping a repaired or replaced BaduStream to a customer 6 Speck Pumps will charge customers for all non warranty work which it may perform Non warranty work will not be performed until the customer has accepted the price quoted 7 Except as specifically set forth above no other warranties whether express or implied including without limitation the implied warranties of merchantability and fitness for a particular purpose are made by the manufacturer In no event will the manufacturer be liable for any loss including time money goodwill lost profits and consequential damages based on contrast tort or other legal theory which may arise hereunder or from the use operation of modification of the pump motor or associated parts The maximum liability of the manufacturer hereu
23. nder shall not exceed the amount actually paid by the customer for the pump motor and associated parts 8 Some states do not permit limitations on the terms of implied warranties or on the recovery of incidental or consequential damages Accordingly the limitations contained in paragraph 7 may not apply to certain customers 9 This warranty gives customers specific legal rights which may vary from state to state The BaduStream is manufactured under license from Speck Pumpen GERMANY
24. out the installation operation and safe use of this product This information should be given to the owner and or operator of this equipment WARNING Before Installing this product read and follow all warning notices and instructions which are included Failure to follow safetv warnings and instructions can result in severe injurv death or propertv damage Call 1 800 223 8538 or visit www usa speck pumps com for additional copies of these instructions When installing and using this electrical equipment basic safetv precautions should alwavs be followed including the following 1 READ AND FOLLOW ALL INSTRUCTIONS 2 WARNING To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times 3 WARNING A work must be preformed by a licensed electrician and must conform to all national state and local codes 4 WARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK connect all ground wires to the grounding terminal located in the control box Use no smaller than a No 12 AWG 3 3mm wire 5 WARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK a bonding connector is provided on the motor for bonding to local ground points such as water pipes metal ladders metal handrails or other metal within 5 feet of the pool All local ground points should be bonded with a No 8 AWG 8 4mm wire Never use gas piping as an electrical ground 6 DO NOT store or use gasoline or other flammable vapor
25. s or liquids in the vicinity of this equipment DO NOT store pool chemicals near the equipment 8 DO NOT remove any safety alert labels such as DANGER WARNING or CAUTION Keep safety alert labels in good condition and replace missing or damaged labels 9 WARNING Stay alert watch what you are doing and use common sense DO NOT use unit if you are tired and or exhausted DO NOT use unit while under the influence of drugs alcohol or any medications 10 Consult your physician before exercising with the BaduStream or using the massage hose 11 DO NOT use or operate the BaduStream if the anti entrapment cover is missing broken or loose 12 Keep and read all equipment manuals Adhere to all of their instructions Refer to them frequently and use them to instruct third party users SAVE THESE INSTRUCTIONS WARNING Entrapment Prevention DANGER DO NOT BLOCK SUCTION A DANGER SUCTION HAZARD Can cause serious injury or death Do not use this pump for wading pools shallow pools or spas containing bottom drains unless pump is connected to at least two 2 functioning suction outlets WARNING Pump suction is hazardous and can trap and drown or disembowel bathers Do not use or operate swimming pools spas or hot tubs if a suction l v outlet cover is missing broken or loose Hazardous suction Can trap hair or body r J parts causing severe The following guidelines provide information for pump installation that
26. tion above the waterline initial priming time may be longer than with regular pool filtration pumps It may take up to 10 minutes This will not damage the mechanical seal 14 Operation continued WARNING Do not use or operate the BaduStream if the anti entrapment cover is missing broken or loose To start swimming jogging or running it is suggested that the two nozzles are pointed slightly inward and slightly upward so that the water breaks approximately 4 ft in front of the BaduStream See Section 5 Nozzle Adjustment to properly adjust the nozzles Start swimming with only minimal force in arms an legs until you feel yourself drifting backwards then add force and swim upstream until a proper balance is found between force and endurance Keep in mind that this unit is designed for a balanced workout Find a pace that you can keep up for at least 20 minutes Out pacing is always possible The idea is to continue exercising for an extended period of time Consult your physician before attempting any strenuous exercise This product may not be challenging or satisfying for all levels of exercise The air regulator permits a controlled mixture of air into the water flow and creates a unique invigorating bubble bath effect It will also add additional resistance to swim against The BaduStream s adjustable flow nozzle s enables the swimmer to regulate the volume of water released through the jet s Turning the nozzle clockw
27. y Complete 22 1 Top Part Air Regulator 23 1 Bottom Part Air Regulator 24 1 Screw Air Regulator M10 x 80 25 1 Hose Ring Air Regulator 16 x 30 x 80 26 1 Gasket Air Control 42 x 11 x 2 27 2 Screw Jet Housing 14 x 1 Extension Ring pre glued not shown Optional Winter Cover Kit Part Qty Description 12 1 Gasket Clamping Ring 9 1 4 Screw M6 x 25 1 Winter Plate not shown Extension Ring An extension ring not shown is available upon request 8 Limited Warranty The manufacturer supplies a limited warranty to the original consumer purchaser of the BaduStream on the following terms and conditions 1 The BaduStream is warranted to be free from defects in material and workmanship for a period of twelve 12 months from the date that the BaduStream is originally installed 2 Not withstanding any provisions herein to the contrary the warranties and obligations hereunder shall not in any event extend for more than 2 years beyond the date of shipment of the BaduStream from Speck Pumps Pool Products Inc in Jacksonville Florida 3 Warranty is void in the following cases damages which result in whole or in part from a careless or improper installation of the BaduStream b improper or negligent use and maintenance of the BaduStream c tampering with the BaduStream by unauthorized repair personnel d ground movement e substitution of parts and or components 4 The manufacturer s sole obligatio
Download Pdf Manuals
Related Search