Service Manual - Whaley Food Service
Contents
1. 15 Repeat for all pins in the harness Note after all pins are transferred there will be eight 8 empty pins at the bottom of the plug 9 L80 111 RevO SPINfresh EBOX Conversion Service Instructions 17 Install harness into 24 pin Molex connector Pin locations Pin 10 DC red Pin 11 RS485 A yellow Pin 22 DC black Pin 23 RS485 B white yellow L80 111 RevO SPINfresh EBOX Conversion Service Instructions 18 Install 24 pin Molex into lower rear mating connector in EBOX Note make sure connector latch is engaged to con tact 20 Using Phillips screwdriver remove the four 4 screws holding encoder board 21 Replace with Encoder board 3WT008 supplied in kit using the existing hardware 11 s0 M RAND 19 Remove 4 pin plug from encoder board located at the lower right side of cabinet RZ jos oe r Ld p iar P O arire 221 e L80 111 Rev 0O SPINfresh EBOX Conversion Service Instructions 23 Reinstall 4 pin connector to the right side of the encoder board to the mating 4 pin receptacle Note this cable routes from the basket motor to the en coder board sO M PAN 21 Plug in 4CT006 harness into the top left mating connector on the encoder board Note harness is the one routing from the ebox 22 Use wire ties to secure harness to main harness in cabinet 1 9 EES N TP1cmi Cane rPi sm ER i nz PI WH2. SERVICE INSTRUCTIONS CONVERT OLD SFC TO NEW SFC Technical Service Upgrade Instructions Please read complete instructions prior to starting WARNING This upgrade kit shall be installed by a qualified service agency in accordance with the manufacturer s instructions and all applicable codes and requirements of the authority having jurisdiction If the information in these instructions is not followed exactly property damage personal injury or loss of life may result The qualified service agency is responsible for the proper installation of this kit This installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturer s instructions WARNING The power supply MUST be disconnected before performing this procedure WARNING Use only the parts supplied with this kit Use of any parts other than those supplied will void the warranty and could cause unsafe conditions or improper operation of your appliance L80 111 RevO Service Instructions SPINfresh EBOX Conversion p PERFECT COMPANYS These service instructions are intended to give you step by step guidelines while converting 1st generation Perfect Fry SPINfresh models SFC as it will be mentioned from here on to the 2nd generation version 2WS802 CL kit Includes Supplied Parts Legend 24 Pin Molex Mini Fit Jr Connector Molex Mini Fit Jr terminals x4 Molex Mini Fit Jr Extractor Tool
3. Encoder board wiring harness V 2 Encoder board 2WS802 EBOX Tools Needed Legend 2 Phillips screwdriver Molex Mini Fit Jr Extractor Tool supplied Molex Mini Fit Jr Crimp Tool 64016 0200 Not Shown 2 L80 111 Rev 0 SPINfresh EBOX Conversion Service Instructions Remove side panel of unit using 2 Phillips screw driver by removing the 5 retaining screws After screws are removed the panel pops out from the bottom right corner then slides out the top WARNING The power supply MUST be disconnected before performing this procedure After panel is removed this is the components that should be visible Please locate all the number components to ensure the following steps apply to the unit you being serviced 1 EBOX 2WS743 2 Encoder Board 3WT006 3 EBOXto Encoder Board Ribbon Cable 3 L80 111 RevO SPINfresh EBOX Conversion PERFECT COMPANYS Service Instructions Remove ribbon cable from Encoder board Cut any all wire ties that attached the ribbon cable to the main harness Disconnect 16 pin Molex connector from the rear of EBOX Remove and set aside Note Main power MUST be disconnected before removal 4 L80 111 Rev 0 Service Instructions SPINfresh EBOX Conversion PERFECT COMPANY Disconnect 20 pin Molex plug from bottom side of EBOX Note Main power MUST be disconnected before removal Remove 6 pin high voltage PLUG FROM REAR OF e
4. IP7 s ie a ODERZ ED C3 LIC TT e K ere ol La r CAD 4 f D a 24 Install is now complete Please reinstall side panel Reconnect main power to the unit Turn on and test per Start up instruc tions located in Operation Manual to insure correct operation Note unit may need basket cali bration please refer to service manual L80 111 Rev 0
5. box Note Main power MUST be disconnected before removal 5 L80 111 Rev 0O SPINfresh EBOX Conversion Service Instructions CUM PAM Using 2 Phillips screw driver remove the three 3 EBOX retainer screws Note Using one hand secure the EBOX so it does not fall after screws are removed 9 After EBOX is removed this is what should be visible 6 L80 111 RevO SPINfresh EBOX Conversion DM PANY Service Instructions EET 10 Using EBOX supplied in kit install using the exist ing hardware Note while tightening screws insure EBOX is flush to the front of the unit 11 Reinstall the lower 20 pin Molex and 6 pin high voltage connectors to the lower and rear upper mating receptacles respectively IF TAMPER SEAL I BROKEN WARRANTY IS VOID o Serial 12350 L80 111 RevO PERFECT Service Instructions SPINfresh EBOX Conversion pmm ore 12 Locate the 24 pin Molex Mini Fit Jr that is supplied in the upgrade kit 13 Using the Molex Mini Fit Jr Extraction tool begin to transfer all the wires from the 16 pin to the 24 pin Molex connector Note all circuits must be transferred to the same pin location that it came from 8 L80 111 Rev 0 SPINfresh EBOX Conversion Service Instructions 14 Starting with Pin 13 white wire remove and transfer each wire 1 at a time is recom mended from their 16 pin location to the corresponding 24 pin location
Download Pdf Manuals
Related Search