SERVICE MANUAL
Contents
1. 0814 a Page 16 of 17 SALAMANDER BROILERS RADIANT AND INFRARED TROUBLESHOOTING INFRARED BURNER SYMPTOM POSSIBLE CAUSE Orifice incorrect size or dirty Incorrect gas pressure Incorrect gas type Flame not orange Orifice not aligned properely in venturi Appliance not venting properly Clogged burner ports Burner malfunction de 2 d 4 5 6 T de Broiler with Infrared burner is mounted too close to a fryer or charbroiler and the grease laden air is causing burner ports to clog If burner ports are found to be clogged install a replacement burner Burner not lighting properly or incorrect burner flame NOTE Grease laden air is detrimental to the life of appearance due to clogged ports the Infrared burner If a technician sees a broiler with Infrared burner mounted in a location close to a fryer or charbroiler please recommend to the customer to move the broiler away from the grease laden air source to prolong the life of the Infrared burner Page 17 of 17 _ 3 F45530 08142. Propane LUBRICATION Anderson and Forrester or comparable valve grease for burner valve stems Apply light coat to valve stems Valve grease must be insoluble in propane and natural gas TOOLS Standard Standard set of hand tools Manometer Special e 3 4 pipe tee two short pipe nipples and a reducer as required to install hose barb to the tee Assemble the parts and retain for future gas equipment use The tool is used for measuring gas manifold pressure after the regulator when a pressure tap is not available in the gas manifold F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS REMOVAL AND REPLACEMENT OF PARTS MANIFOLD COVER Shut off the gas before servicing the unit 1 Loosen set screw and remove knobs from control valves 2 Remove screws that secure manifold cover and remove the cover 3 Reverse procedure to install MANIFOLD COVER IIM A Fig 1 TOP PANEL ASSEMBLY Shut off the gas before servicing the unit NOTE When viewed from the top there are 5 flue bracket mounting screws that secure the bracket and the insulation pan underneath to the top panel only When removing the top panel assembly these screws can remain installed 1 Remove LEFT SIDE PANEL and RIGHT SIDE PANEL 2 Remove the remaining screws securing Top Panel Assembly to each side of the flue and back panel Lift the Top Panel Assembly off b
3. servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame 1 Remove MANIFOLD COVER 2 Left Valve A Disconnect compression fitting from top of valve B Remove screws securing manifold to broiler C Note orientation of elbow on valve then remove the elbow Retain for use on replacement valve D Remove valve from manifold CM FITTING y LEFT SIDE Fig 8 3 Right Valve A Remove RIGHT SIDE PANEL B Disconnect compression fittings from right side manifold C Remove screws securing right front manifold and right side manifold to broiler D Note orientation of control valve then remove it from the each of the manifolds NOTE When installing ensure control valve is perpendicular to the right front manifold WARNING Clean pipe threads and apply thread sealant that is suitable for use with propane gases 4 Reverse procedure to install 5 Check for proper operation F45530 0814 COMPRESSION __ FITTINGS _ RIGHT SIDE Fig 9 PILOT 36RB C36RB A WARNING Shut off the gas before servicing the unit A WARNING All gas joints disturbed during servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame 1 Remove MANIFOLD COVER 2 Disconnect compression nut from straight pilot valve fitting NOTICE When disconnecting compression nut from the straight
4. with propane gases F Apply thread sealant to pipe threads and re install GAS ORIFICE CHECK The gas orifice is mounted at the gas and air inlet for the burner If burner operation seems poor and other systems have been checked access the burner and inspect Gas orifice alignment orifice should be centered in the venturi opening and perpendicular to the burner e Check gas orifice for blockage or damage If dirty clean with air or water only e Verify gas orifice is correct for the altitude Page 14 of 17 SALAMANDER BROILERS RADIANT AND INFRARED SERVICE PROCEDURES AND ADJUSTMENTS GAS ORIFICE 3 Check for proper operation fee TENSION E ADJUSTMENT O eas NUT ESTAS AS ASEA e E RADIANT BURNER Fig 37 RIGHT SPRING SHOWN Fig 39 GAS ORIFICE INFRARED BURNER 26930 Fig 38 CONTROL VALVES Inspect the control valve for smooth rotation noticeable wear and any possible damage The burner flame should increase smoothly as the valve is opened highest setting and decrease smoothly as the valve is being closed When inspecting valves always apply a light amount of valve grease at the base of the valve stem See LUBRICATION If valve grease does improve rotation of the valve or damage is found replace the control valve as outlined under CONTROL VALVES 36RB C36RB or CONTROL VALVES 36IRB C36IRB RACK SPRING TENSION ADJUSTMENT 1 Access the springs on the bottom of broiler 2 T
5. SERVICE MANUAL SALAMANDER BROILERS RADIANT AND INFRARED WOLF VULCAN 36RB 36IRB WOLF C36RB C36IRB This Manual is prepared for the use of trained Vulcan Service Technicians and should not be used by those not properly qualified This manual is not intended to be all encompassing If you have not attended a Vulcan Service School for this product you should read in its entirety the repair procedure you wish to perform to determine if you have the necessary tools instruments and skills required to perform the procedure Procedures for which you do not have the necessary tools instruments and skills should be performed by a trained Vulcan Service Technician The reproduction transfer sale or other use of this Manual without the express written consent of Vulcan is prohibited This manual has been provided to you by ITW Food Equipment Group LLC ITW FEG without charge and remains the property of TW FEG and by accepting this manual you agree that you will return it to ITW FEG promptly upon its request for such return at any time in the future For additional information on Vulcan Hart Company or to locate an authorized parts and service provider in your area visit our website at www vulcanequipment com VULCAN HART DIVISION OF ITW FOOD EQUIPMENT GROUP LLC BALTIMORE MD 21222 www vulcanequipment com F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED TABLE OF CONTENTS GENERAL nore noe tee eee ea
6. UBRICATION Left amp Right Valves Ensure control valves are aligned and centered in the manifold cover opening The valves must be perpendicular to the manifold 4 Reverse procedure to install 5 Check for proper operation PILOT 36IRB C36IRB Shut off the gas before servicing the unit A WARNING All gas joints disturbed during servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame 1 Remove MANIFOLD COVER LEFT SIDE PANEL if replacing left pilot and RIGHT SIDE PANEL if replacing right pilot 2 From inside the broiler cooking area disconnect compression fitting from the pilot NOTICE When disconnecting compression fitting for the pilot support bracket to prevent bending 2 Say z CS ee j BN s duet aia oy dE AA E El E Pa O F iby ha fA ts 5 TETE a Al nia uu tn r dh a a aa a DJA IA I Ti TE TE TE TE T E y PR pi PES A p PERG NEO AR p F a WARA 7 Mal A fd a oe ARA as 4 e a miga Y g w vi en pe mse p y K Y t Ak AN i ae COMPRESSION FITTING ir 26918 Fig 20 3 Remove screws securing pilot and bracket to the broiler F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS BURNER MOUNTING BRACKET 4 Right side Fig 21 A Disconnect gas supply at broiler 4 Remove screws securing pilot to the bracket B Remove screws securing manifold to br
7. a See ee a ee eee oe ang eet om ane oe se ee yeas eee hee eae ed aaa pease 3 INTRODUETION 1 sigues ternera ses pete seda eds sore senta tag sere E Deo ette E a 3 INSTALLATION OPERATION AND CLEANING 2 co0 ce ddie ss ses da de athe is ale anand atea Se he ane dies 3 RACK POSITION AND GAS SETTING concreto rssasrovra Soe ia tuplas certo ode eines 3 MODELS eee ee eee ee ee ee ee ee ee eee 3 SPECIFICATIONS ioicoisiotato isc tots piropo besitoss 3 PUBRICATIO N oo tiepiscr ricardo aereas 3 FOOL aa EEE e EN 3 REMOVAL AND REPLACEMENT OF PARTS 00 00 eee eee eaer A MANIFOLD COVER icc cee teen bees seiya dadas yea peas ure sora pabadeneaesendennedaneess A TOP PANEL ASSEMBLY sosiece den cees bene dp nese beets ess tere bene pen bee dee oe ea peas 4 LEF TOIDE PANEL se tee tee mi gigia dee ee ere eee ee a E a EA S aea ene ded a aa a A E R dotes 4 RIGHT SIDE PANEL a5 istiga ii i aS seeds dete a aE ae AE a a aia teo aoe bee a a tes ic 5 CONTROL VALVES SORB COORB Pess 25 abs dia redada di ae 6 PILOT 430 COORD gi tony fe pepe resis bi desa da cio Ea eva tes 6 RADIANT BURNER 36RB C36RB posordrsssr rante ras ei dr aer 7 CONTROL VALVES 36IRB C36IRB secinsadtasetesi clostacotaseeshacesagdecesseeusesssacdeeneteeuseconz 8 PILOT AIRE C S6IRD egg coe chose sapo osas poe aia one nes 9 INFRARED BURNER 36IRB C36IRB abc esatoioeuisios senos pda ios ae a 10 GAS PRESSURE REGULATOR suis boss sor seo ist ae ot 12 RACK SPRINGS stilo pias yaoi ay iaa olas
8. ate under crumb tray for manifold pressure setting information Clean vent cap before adjusting NS E gt 1 2 psic Po 3 0 6 0 Fig 35 1 Connect manometer to measure gas manifold pressure A 36RB C36RB Remove MANIFOLD COVER to access pressure tap on the manifolds B 36IRB C36IRB Install a tee with hose barb connection on the outlet side of the regulator See TOOLS Connect the opposite end of the tee to broiler incoming gas supply Turn gas supply on and light both pilots Open both valves to the full on position and check manometer reading The reading should be 5 W C for natural gas and 10 W C for propane gas Tolerance is 0 3 W C 4 If manifold pressure is not correct adjust the regulator as follows A Remove the regulator closing nut F45530 0814 REGULATOR CLOSING NUT Bie By e a A gt co gt 1 2 psic Po 3 0 6 0 t eY oos Y i 18757 Fig 36 B Insert a flat edge screwdriver through the top of the regulator While watching the manometer turn the adjusting screw clockwise to increase pressure and counterclockwise to decrease pressure until the proper gas pressure is achieved See data plate under crumb tray C Install the regulator closing nut Turn gas supply off E Remove manometer from pressure tap location If tee was installed remove tee WARNING Clean pipe threads and apply thread sealant that is suitable for use
9. contained in this manual are based on the latest product information available at the time of printing INSTALLATION OPERATION AND CLEANING For detailed installation operation and cleaning instructions refer to Installation amp Operation Manual sent with each unit The manual is also available online at www vulcanequipment com NOTE Using accessory options Salamander broilers can be mounted to the wall over a range or placed onto an appropriate table top by using 4 legs RACK POSITION AND GAS SETTING NOTE Infrared burner models must use the full gas setting Knob fully counterclockwise to achieve the best burner performance and highest broiler temperatures Lower broiler temperatures can be achieved by using a lower gas setting Knob in the range just past off but less than fully counterclockwise When using a lower gas setting the flame should remain lit and be steady across the entire burner surface For detailed information refer to RACK POSITION AND GAS SETTING in the Installation amp Operation Manual MODELS Vulcan e 36RB N natural e 36RB P propane Wolf e C36RB N natural e C36RB P propane Page 3 of 17 SPECIFICATIONS Gas Pressures e Manifold Operating Pressure Natural 5 W C Propane 10 W C e Inlet Supply Pressure Natural Recommended 7 9 W C Minimum 7 W C Propane Recommended 11 12 W C Minimum 11 W C Maximum 14 W C 0 5 PSI Natural or
10. e flame is a result of excessive primary air NOTE The factory default air shutter positions are half open natural full open propane AIR SHUTTER RADIENT BURNER Fig 34 INFRARED BURNER 36IRB C36IRB Adjustment The only adjustment for the Infared burner is the gas manifold pressure Verify the pressure is set correctly as outlined under REGULATOR ADJUSTMENT Flame Appearance When the Infared burner first lights you should see a small rolling blue flame which will clear up after the burner warms Once warm a low profile orange flame is the best description of the Infared burner flame In some cases if the burner is operating correctly you may not be able to see the actual flame Instead you will see the glow of the ceramic bricks in the burner REGULATOR ADJUSTMENT Shut off the gas before servicing the unit NOTE Regulators come preset but should be checked anytime one is installed Before adjusting regulator check incoming gas line pressure Incoming pressure must be 6 14 W C for natural gas and 11 14 W C for propane gas If incoming pressure is not correct have the gas source checked and adjusted as necessary Make sure the regulator is mounted in the horizontal position with the arrow pointing in the direction of gas flow See GAS F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED SERVICE PROCEDURES AND ADJUSTMENTS PRESSURE REGULATOR under REMOVAL AND REPLACEMENT OF PARTS See unit data pl
11. ide until it clears the burner opening in broiler frame on the left Lift burner to remove it from broiler 8 Remove screws securing the left burner mounting bracket to burner BURNER MOUNTING BRACKET DANY E E E Ay iy Te gt AAA rssh o Fig 27 oa see ROAR as 6 Lift right side burner mounting bracket from ee 77 yy Ge burner and broiler frame aes a ns 26926 Fig 29 9 Reverse procedure to install replacement burner NOTE When installing remove the left side orifice bracket from the broiler for additional burner clearance as necessary 10 Check for proper operation Page 11 of 17 _ 3 F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS GAS PRESSURE REGULATOR A WARNING Shut off the gas before servicing the unit A WARNING All gas joints disturbed during servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame WARNING Clean pipe threads and apply thread sealant that is suitable for use with propane gases NOTE Gas pressure regulator should be installed as close to the broiler inlet gas connection as possible 1 Thread regulator onto pipe hand tight with arrow pointing in direction of gas flow to the broiler REGULATOR ADJUSTMENT BELOW CLOSING NUT _ 18755 Fig 30 2 Tighten regulator securely in horizontal position with the regulator adjustme
12. ighten nut to adjust rack spring tension Adjust both springs equally so there is approximately 3 4 of thread above the nut If additional rack spring tension is required tighten each nut an additional 2 3 turns Page 15 of 17 _ 3 F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED TROUBLESHOOTING TROUBLESHOOTING GENERAL ALL MODELS GENERAL SYMPTOM POSSIBLE CAUSE Incorrect gas type o Incorrect gas pressure Pilot does not remain lit Pilot burner not adjusted properly Pilot burner blocked or Incorrect pilot orifice Incorrect gas type Low gas pressure Slow to heat or not hot enough Regulator adjustment or malfunction Control valve malfunction Incorrect gas type Regulator adjustment or malfunction due to high gas Broiler temperature too hot pressure Control valve malfunction RADIANT BURNER 36RB C36RB RADIANT BURNER SYMPTOM POSSIBLE CAUSE Orifice incorrect size or dirty Air shutter not adjusted correctly or dirty Incorrect gas pressure Flame too yellow Orifice not aligned properely in venturi Appliance not venting properly Regulator adjustment or low gas pressure Low burner flame all burners i i i Incorrect gas type Low burner flame individual burner 1 Air mixture incorrect 1 Inadequate air supply Flame floats on burner 2 Restricted exhaust flue INFRARED BURNER 36IRB C36IRB 1 2 3 4 Incorrect gas type Os 6 1 F45530
13. ion RADIANT BURNER 36RB C36RB Shut off the gas before servicing the unit 1 Adjust rack assembly to the center position Page 7 of 17 2 Pull rack assembly out and access the rack stops on the left and right sides of the rack assembly Allow enough clearance at the rear of rack assembly to rotate the rack stops to a horizontal position If the rack assembly is pulled all the way out the rack assembly will engage the rack stops and prevent removal RACK LEFT SIDE SHOWN Fig 12 3 Grasp the rack assembly near the broiler rotate both the rack stops horizontally and pull the rack assembly out enough for the rack assembly frame to clear the rack stops 4 Grasp the rack assembly and drip tray on each side to support the tray and remove from broiler F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS CN A i a CONTROL VALVES 36IRB C36IRB Shut off the gas before servicing the unit A WARNING All gas joints disturbed during servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame 1 Remove MANIFOLD COVER 2 Left Valve Fig 14 A Remove screws securing valve mounting 5 From inside broiler cooking area remove cotter bracket to broiler pin securing burner to broiler frame Retain pin B Disconnect compression fitting from the for reuse elbows at the top and bottom of valve C Note orientatio
14. isa i CSR a my Sears y Mee ze i Dr Lo ee esa f DEA ha NS E tye staal Peon dite san ES ae AO a q e nLite WMS way tere ae pr DA IPRS then oe el ay g Saber 4 es 4 Ware nt q hs e Ene x A PA a RAEC hy Gi 7 ite S er fatale Y pa Teh q Me o ee 4 ilag y hisa f Ww a PILOT AS ADJUSTMENT A SCREW 26928 Fig 33 2 Locate the pilots at the top of the broiler heating area 3 Monitor the pilots flame and burner lighting Pilot is in adjustment when it will stay on continually and lights the burners without delayed ignition 4 If adjustment is necessary rotate the screw clockwise to decrease and counterclockwise to increase flame height RADIANT BURNER AIR SHUTTER ADJUSTMENT 36RB C36RB The efficiency of the burner depends on a delicate balance between the air supply and volume of gas Whenever this balance is disturbed poor operating characteristics and excessive gas consumption may occur An air shutter on the front of the burner controls the gas mixer balance A yellow streaming flame on the burner is an indication of insufficient primary air To correct this condition loosen the shutter screw and rotate the air shutter open until the flame begins to lift from the burner then close the shutter slightly and tighten the shutter screw A proper flame should be blue in color well defined and seated on the burner Page 13 of 17 port A white blu
15. n of elbows on valve then BURNER remove the elbows Retain for use on replacement valve Pra lt aie ULL itt Fig 15 oe ie 6 Lift burner from the rear and slide it off the gas COMPRESSION orifice to remove from broiler s FITTINGS M e are lg z E pe AA Vis Pits in Vin Win Yia in e Win Pin he Mun gt FRIDA AA LEFT VALVE Fig 17 3 Right Valve A Remove screws securing valve stem assembly to valve TOP VIEW INSIDE COOKING AREA Fig 16 7 Reverse procedure to install 8 Perform RADIANT BURNER AIR SHUTTER ADJUSTMENT 36RB C36RB F45530 0814 a Page 8 of 17 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS VALVE STEM ASSEMBLY A _ as Tan E 26914 RIGHT VALVE Fig 18 B Note location of spring and remove it if still inside valve body MANIFOLD CONTROL VALVE 7 4 wr e E COMPRESSION Pai FITTING SaM Fig 19 C Disconnect compression fitting from the elbow at the bottom of valve Remove valve from manifold E Note orientation of elbow on valve then remove the elbow Retain for use on replacement valve Page 9 of 17 WARNING Clean pipe threads and apply thread sealant that is suitable for use with propane gases NOTE When installing Right valve apply a light coat of valve grease under the stop on the valve stem see L
16. nt upward as described on regulator NOTE Regulator will not function properly without adjustment screw pointing upward 3 Connect main gas supply line to gas pressure regulator inlet 3 4 REGULATOR INCLUDED 3 4 NIPPLE MAIN GAS 3 4 x 3 4 SUPPLY IN ELBOW id FLOW TO SALAMANDER BROILER 26906 Fig 31 F45530 0814 4 Adjust regulator as outlined in REGULATOR ADJUSTMENT RACK SPRINGS NOTE Springs should be replaced in pairs for proper operation of the rack lift assembly 1 Remove crumb tray to access tension adjustment nuts from the front of broiler 2 Raise the rack lift assembly to its highest position on stop plate to relieve spring tension 3 Loosen nuts to remove any remaining tension on springs 4 Access the bottom of broiler and remove springs from the lower arm casting and eye bolt TENSION _ ADJUSTMENT NUT BOTTOM OF BROILER RIGHT SPRING SHOWN 26927 Fig 32 Reverse procedure to install Perform RACK SPRING TENSION ADJUSTMENT Page 12 of 17 SALAMANDER BROILERS RADIANT AND INFRARED SERVICE PROCEDURES AND ADJUSTMENTS SERVICE PROCEDURES AND ADJUSTMENTS PILOT FLAME HEIGHT 1 Locate the pilot adjustment screws below the burner control knobs one on each side on the front of broiler It is not necessary to remove the manifold cover as adjustment access holes are provided in the panel i gt my E X aye DEN ET sac A As y CES p et ys eat iy Vin
17. oiler a a a a e a 2 ys Fig 24 Fig 22 C Lower the manifold to access burner mounting bracket screws 5 Reverse procedure to install and check for proper operation D Remove screws securing burner mounting n bracket to broiler frame INFRARED BURNER 36IRB BURNER MOUNTING BRACKET C36IRB A WARNING Shut off the gas before servicing the unit A WARNING All gas joints disturbed during servicing must be checked for leaks Check with a soap and water solution bubbles Do not use an open flame 1 Remove MANIFOLD COVER LEFT SIDE PANEL and RIGHT SIDE PANEL Remove TOP PANEL ASSEMBLY Pig aa E Disconnect compression nut from elbow 3 Left side En orifice fitting to access the right side orifice A Remove screws securing burner mounting bracket mounting screw bracket to broiler f TACKE SFE INANE F Remove screws securing orifice bracket to broiler frame F45530 0814 a Page 10 of 17 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS AN E BURNER gt MOUNTING BURNER a BRACKET Dor oo o AA G Ly N YY AW Wy W gt i A a we gt y ik A N Qoo a KAR 26923 Fig 26 RIGHT 5 From inside the broiler cooking area remove screws on the of bottom right side of the burner The screws secure the burner mounting bracket to the burner TOP VIEW SHOWN Fig 28 7 Slide burner to the right manifold s
18. os ini 12 SERVICE PROCEDURES AND ADJUSTMENTS 10d srestnl edad cds ao aa ei 13 PILOT FLAME RERET arra yii ete AEEA EEE E re E EEE EE E EEE ite eee caes 13 RADIANT BURNER AIR SHUTTER ADJUSTMENT 36RB C36RB 00000 00 cece eee 13 INFRARED BURNER 36IRB C36IRB scpe cece eeu perrea beeen renarna aaeeea 13 ADJUSTMENT sacos raso e ro a ed iaa mias 13 FLAME APPEARANCE swaai a piada dap daa ea a a tados dsp pace cortaba aca papis 13 REGULATOR ADJUSTMENT cvovoodioriapevenescasaos a i ka a ELA a a esa a pao A E A E A Ea a a miss 13 GAS ORIFICE CHECK ovinos vs penis E ie aa de y ein 14 CONTROL VALVES espcositrcsrero inodoros tes pr o e as eta is ree azar 15 RACK SPRING TENSION ADJUSTMENT ooocccccccccccccccccccccc eee eee eee eens 15 TROUBLESHOOTING s ceweye as mass Ge EEE EPER datado vea ada de 16 GENERAL ALL MODES ese rinpa pepe eee eee yee eee nee eset eee ee eno cont pene ee eee eae a 16 RADIANT BURNER CRB Go0RB scorpressorspral gaa aces sade eae rico raso eres 16 INFRARED BURNER 36IRB C36IRB te oii soe sarees arado poo pa cies go aros 16 HOBART SERVICE 2014 F45530 0814 Co Page 2 of 17 SALAMANDER BROILERS RADIANT AND INFRARED GENERAL GENERAL INTRODUCTION This manual is for the Vulcan and Wolf Gas Salamander Broilers Procedures in this manual will apply to all models unless specified Pictures and illustrations will be of model 36IRB unless otherwise noted All of the information illustrations and specifications
19. pilot valve fitting support the fitting to prevent damage to pilot flexible tubing 3 Remove screws securing pilot and bracket to the broiler PILOT SCREWS ree AS COMPRESSION AM LEFT SIDE NUT SHOWN Fig 10 4 Remove pilot through broiler cooking area 26937 Page 6 of 17 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS ap M BURNER el IGNITION y PORTS Pm s A re F Z HN 26938 Fig 11 5 Remove pilot from bracket 6 To install replacement pilot A Insert mounting groove on the pilot into the mounting slot on the pilot bracket B Re crimp the pilot bracket to secure the pilot C Slide compression nut and sleeve ferrule over one end of the replacement flexible tubing for the pilot Insert flexible tubing into the pilot and tighten compression nut to secure D Bend flexible tubing to match original pilot configuration Route flexible tubing through opening in broiler frame and install pilot bracket to broiler NOTE When installing ensure the pilot is close to the ignition ports on the bottom of burner for proper burner lighting If necessary bend the bracket so that the pilot remains in contact with the burner casting E Slide compression nut and sleeve over the opposite end of flexible tubing Insert flexible tubing into the straight pilot valve on broiler and tighten compression nut to secure 7 Check for proper operat
20. roiler Reverse procedure to install F45530 0814 FLUE BRACKET Fig 2 LEFT SIDE PANEL Shut off the gas before servicing the unit 1 Remove crumb tray 2 Remove MANIFOLD COVER 3 Position the rack assembly to access panel screws in the broiler opening area Page 4 of 17 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS 4 Remove screws securing left side panel Slide 4 Pull knob off the handle on rack positioning panel toward the front of broiler until panel clears bracket then remove plate stop front mounting area then remove the panel Y AE 5 Position the rack assembly to access panel screws in the broiler opening area Remove screws from this area and the front of panel p ad e i Vo No k Pad mp 26909 Ig Fig 6 oe MASvelse POP cule no etal 6 Remove screws securing right side panel to RIGHT SIDE PANEL broiler Slide panel toward the front of broiler until panel clears front mounting area then remove the Shut off the gas before servicing the unit 1 Remove crumb tray 2 Remove MANIFOLD COVER 3 Remove screws securing plate stop to broiler PLATE STOP Fig 7 7 Reverse procedure to install Page 5 of 17 _ 3 F45530 0814 SALAMANDER BROILERS RADIANT AND INFRARED REMOVAL AND REPLACEMENT OF PARTS CONTROL VALVES 36RB C36RB A WARNING Shut off the gas before servicing the unit A WARNING All gas joints disturbed during
Download Pdf Manuals
Related Search