How to transplant Satellite Navigation between
Contents
1. DVD Drive Now because it s a FACTORY installed Sat Nav The DVD drive is found in the Glove box In the TOP INNER Right corner passenger side of the AUDM Liberty Wiring Harness 1 Din Cable and Antenna Cable This Wiring Harness consists of a round 13 pin din cable and a Coaxial cable with a square connector This cable DOES NOT require any modification and can be removed intact Wiring Harness 2 DVD Drive Power and Signal Cable CN100 This is a single connector that s supplies the power and relevant signals to the DVD Drive Yellow Red 12V Accessory Brown Yellow Reverse Light Black Yellow 6 Light Blue Red Illumination amp Backup Light Hand Brake Ground Green Black ABS Speed Sensor Doesn t appear to exist although it is listed on the wiring diagram from service manual As long as you have disconnected the battery you can cut these wires off about 4 5 inches back from the plug so that the future owner can make the transplant harness Cut each wire individually if possible and make some longer and some shorter then cover in lots of tape individually then altogether This Connector will be referred to as CN100 Wiring harness 3 Screen Power and Screen HU Signal Cable This harness can be removed but you will have to cut some wires You only have to cut wires that go to the Power or Signal areas of the car The cables that run to the head unit MUST REMA2. You will notice that there is a yellow RCA input on the rear of the screen To use this whilst in motion you must have completed the Screen Park Brake Lockout Removal rinia If you have not completed this hack you must have the hand brake on to SSEM E use AUX _ Simply plug an RCA lead into the plug on the back of the monitor and run the other end where ever you want to for easy access 12 To engage the AUX input turn the ignition to ON not ACC then push INFO twice Your screen will go black if nothing is plugged in or you will see whatever is plugged in Your signal must be NTSC in Australia we use PAL these days most devices are capable of NTSC a media player such as the ASTONE AP 110 is perfect because it is 12 volts Pree SRN Reeve supports NTSC and they are well priced Reversing Camera Not Confirmed You will have noticed that there is a four pin plug on the back of the screen This is areversing camera input You can purchase a premade adaptor for this to connect a reversing camera up Or the pinouts are as follows Video GND Rear DET Voice Commands Not Confirmed It appears that the DVD drive has a 5 pin plug on the back This is for a microphone to do voice commands I am unsure if this actually works however seeing the fact that it has a microphone volume level option and reads push button to start in the menu it possibly could You would most likely need to purchase a Kenwoo
3. the map within a couple of minutes you will need to set the date Now push the MENU button then imagine there is a button on _ g the touch screen in the middle at wination Sore l the top Touch there and hold it until a keypad prompt comes up NAY r The classified super top secret code which you can t tell anyone is n Now you are in the diagnostics menu 1000 08 29 05 Vehicle Signal GPS Informati i if you click Navigation info Reset Position Then Vehicle Signals you can VEHICLE GVRO SIGNALS see if the sat nav detects that Vehicle fo 9 e you re in reverse hand brake is SPD Pulse Count on or illumination is enabled tag peo These signals are from the DVD hapten t eiative Bearing Drive Connector Gvro Sense Press the Info button and see 1f it has the a i C trip meter information and fuel usage E A Be x xm information 4586 ta DISTANCE 4 te 0 03 tine 0 03 9 Sim wocom 23 4 tim Oe lt 11 REV GPS VEHICLE SIGNAL Take it for a test drive STRICTLY BEFORE DRIVING Press MENU then go to NAVIGATION SETUP then select NAVIGATION Satellite INFORMATION then select os VEHICLE SIGNAL Notice on the Latitude right it says SPD Now you can drive and it will tell you the speed a Longitude Your Satellite navigation should now be completely
4. How to transplant Satellite Navigation between Navigation and Non Navigation Liberties Disclaimer I take NO RESPONSIBILITY for any damages caused to your car sat nav body life marriage or any other aspect which maybe included This is for Informational Purposes only if you are an incompetent fool or don t want to install or remove a Subaru Liberty Satellite Navigation Unit then don t bother reading anymore Removal of the factory navigation unit The factory sat nav consists of 7 parts they are Screen Dash Surround Antenna DVD drive Wiring harness Din Cable and Antenna Cable Wiring harness 2 DVD Drive Power and Signal Cable Wiring harness 3 Power and Signal Cable oe ot eee I wasn t around when the unit was removed from the car so the removal information is basic It is mainly focused on what wiring needs to be removed gt a y Py INN Y Screen aT l ST D NIA The Screen is a Kenwood SS FGZ203MEF2 it has been customised by Subaru to there specifications E G Subaru start up logo and so on EA ee Pi e y EP Ss ry PEETI L o Ste eae of Bus Dash Surround Pretty self explanatory It 1s the part with the air vents and the 7 inch hole through the middle You can t miss it 7 ACS ADELA LIGD UAE AAS NGG Antenna This is easy to miss it s a small black box that is mounted on a right angle bracket I believe it is behind the instrument cluster Speedo panel
5. IN INTACT On this cable the 20 pin plug is the link for the screen to stereo The 16 pin plug is the signal and power into the screen McIntosh Plug Screen Plugs The wires you will have to cut are Pink 0G CAN BUS Light Blue Red Illumination amp Backup Light These Two Wires are Twisted Together Leave as much wire as possible from the plug so that the future owner can make the transplant harness You may be able to cut this near the stereo wiring harness You now have successfully removed the sat nav from a Subaru Liberty Installation of the factory navigation Harness numbers are different in the following section This is where I was actually involved Check the NON STANDARD MODIFICATIONS SECTION on page 12 to see if you would like to integrate any of these HARNESS L4 DVD Driver Screen and Headunit iPower and Signal Harness 3 CAN BUS lt gt ee Harness pr Power Signals and Illumination Harness 4 Signals To install the factory sat nav I made 4 harnesses that connects everything up therefore no soldering in the car and completely reversible if you decide it s not for you What you will need to make the harness REQUIRED ITEMS APROX PRICE Heat shrink CABAC 350pc heatshrink tubing pack Metra 70 8901 2 6 P amp H Metra 71 8901 13 9 P amp H 12 pin plug amp socket Generic 4 Pin Plug amp socket Generic H0077AGO000 Norenwake Ha
6. d KNA VC300 13 Reference Section Subaru Service Manual Reference Drawings I used drawings from the Subaru Legacy 2004 service manual I can t remember where I got them from but Google search for it They were AUDIO RM 01 RHD MODEL WITH MCINTOSH NAVI R 01 02 NAVIGATION SYSTEM AUDIO RWS 02 AUDIO SYSTEM ONLY FOR STEERING CONTROLS BACK L R 01 BACK UP LIGHT SYSTEM JLLUMI R 04 CLEARANCE LIGHT AND ILLUMINATION LIGHT SYSTEM Also had a look at Kenwood FGZOOOQUF2 service manual and Kenwood KNA 3100 3200 service manual Note both were North American Pinouts CN 100 DVD Drive Power amp Signal Connector Black Yellow 6 Ground i O Violet 8 Miltummination Grey 9 Hand Brake Switch 14 16 Pin Power and Signal Cable Pink Twisted 6 CAN BUS lightBlue Red_ 8 amp 8 Milumination amp Backup Mcintosh Radio Pinouts ww g a x ie asal i Wa S atti Socket Aftermarket Plug Factory Harness eee Green Violet White 3 Steering Wheel Controls Light Blue Red 6 Ilumination amp Backup Lights Orange White 9 Steering Wheel Controls 12V Accessory 15
7. e continuity of the cables before you plug it into the car saves troubleshooting it when you have it in the dash Continuity Checklist Wire Colour 12 Pin Plug CN 100 Pin Screen Plug Function Pin Pin Number Violet Tight ae 7Red_ 7 Minato Backup Cig Ignition Wire Yellow Red 4 2 7 12V Accessory Green Black 5 10 2 ABS Speed Sensor Grey 7 13 Hand Brake Switch Brown Yellow 8 amp 8 J 5 4 Reverse Light Pink Twisted 9 NA 6 _ CANBUS _ Black Yellow 11 6 15 amp 16 Ground _ Doesn t appear to exist on my DVD drive Connecting up your Completed Harnesses This part is quite easy because it s simply plugging it together into the respective spots CN 100 DVD Drive Power amp Signal Plug Stereo Wiring Harness Socket Mcintosh E Power Plug Mcintosh Signal Plug 4 Pin Connector to OP Port Plugs to Screen Completing the install Once you have everything tested and installed Ask yourself have I done it correctly If you believe the answer is yes then AT YOUR OWN RISK take the punt and turn that key You should see a nice looking SUBARU logo That s a good start You may notice that the McIntosh just turned off Push the FM button It should come back on Now that your sat nav is on insert the GENUINE SUBARU MAPS DISC into the Navigation drive It should mess around a bit and then bring up
8. installed and fully functional NON STANDARD MODIFICATIONS Due to Australian Law It is illegal to program a sat nav whilst the car is in motion and it is also illegal to have a video entertainment screen available to the driver whilst the car is in motion Park Brake Lockout Removal For Screen AUX To remove the park brake lock for the screen you need to make the screen think the handbrake is on To complete this on the transplant harness you need to ground pin 13 on the screen connector This is the grey wire The easiest method is instead of putting it into the 4 pin connector which would attach to the op port attach it to a piece of wire witha spade connector onone end and a fork or ring connector on the other put the ring under a chassis screw for a permanent ground And put the spade connector on the removed pin and cover with heat shrink For DVD Drive So your passenger can change the destination whilst in motion you have to make the DVD drive think that the handbrake is on This is achieved by making pin 9 on the CN 100 plug go to ground You could use an old lug which you may have to cut up a little to make fit in the connector then put a fork lug on the other end and terminated it under a easily accessible screw under the end panel of the dash which is in the metal frame so if the need comes to reverse the process you don t need to pull the entire car apart again Or use a double throw switch AUX input NTSC
9. lar to option 2 in the OP connector section Pin Positions in this Picture are NOT for CAN BUS Signals Fourth Harness The OP Plug OPtions Plug or B228 exists in the MY08 GT Spec B AUDM Liberty It is tucked up behind the fuse box near the accelerator and by tucked up I mean like half way up the back of the fuse box It is rolled up and taped with pink electrical tape Don t get confused with the other two connectors taped a bit lower and easier to access they are not the ones you need Brown Yellow __ 67 Reverse Lights Grey 8 Park Brake Switch I put a 4 pin plug on the transplant harness to aid in the modular construction Then the other side of the four pin plug you have options they are Option 1 I recommend buying a HO077AGO000 Norenwake Harness from Japan Parts Around 20 AUD You need to tap off wires 3 5 6 and 8 Option 2 If you are lucky enough to have a spare plug with pins around then you can cut the solid plastic shroud off and then mount only the pins you need Similar to Option 2 of the CAN BUS section Option 3 If you don t want to buy the harness and don t have a spare plug then the pins that you removed from the Metra stereo harness slot in perfectly to the OP Connector This should complete Parts 2 3 and 4 of the wiring harness Checking your harness is correct Now your harness should be complete with plugs on all ends You should check th
10. rness 20 Shipping 4 S o Tape Jaycar Bunnings 1 35 2 10 Jaycar DSE 11 15 DVD Drive Screen and Head unit Power and Signal Harness First Harness With your navigation unit you should of received the power and signal plug for the DVD drive or the CN100 Plug with a small tail of wire Because Subaru have good standards they keep wire colours consistent This is good news for us You need to join the following wires individually in a T Joint Wire Colour Yellow Red 12V Accessory Brown Yellow Reverse Light Black Yellow Light Blue Red Illumination amp Backup Light Grey Hand Brake Ground Green Black ABS Speed Sensor Doesn t appear to exist on my DVD drive CN 100 DVD drive power and signal Illumination GND Wire Tails 16 pin cable to screen You should have tails for the following wires Wire Colour Illumination amp Backup Light CAN BUS These wires are twisted together I put a 12 pin plug I purchased from Jaycar on these to complete this part of the harness It helps make it modular This should complete the harness which plugs into the DVD Drive Screen Head Unit to a 12 Pin plug This is the DVD Drive Screen and Head unit Power and Signal Harness Power signals and illumination Second Harness I purchased a male and female stereo wiring harness and made what I call a tapping harness They are Metra 70 8901 Socke
11. t and Metra 71 8901 Plug A little trick is 1f you use a precision jewellers flathead screwdriver 1 3mm you can remove the pins which you don t need This is really good if you have the McIntosh Stereo You simply look down the socket plug and you will see a small white clip on top of the silver contact lift it with the screwdriver and pull the wire tail I have the McIntosh stereo so I made this tapping Harness Will be different for Kenwood Stereo 11 t I put these wires on the corresponding pins of the 12 pin plug I installed That is how I got 5 of the 1 wires leaving 6 remaining 2 of them are the CAN BUS The other 4 can come from the OP Connector OPtions Connector a k a B228 reference to this is found in harness four CAN BUS Third Harness I decided to separate the CAN BUS to its own plug I soldered a plug I had onto the transplant harness side Violet and Pink twisted wires With the other side of the connector there are two options Car Side Ilumination GND GND Mcintosh Side Option 1 You can use two of the spare pins removed from the Metra wiring harness and connect them to the 4 pin 1103 Connector only 2 wires are used then taped them in place so the new connector is the only accessible one Option 2 If you are lucky enough to have a spare plug with pins around then you can cut the solid plastic shroud off and then mount only the pins you need Simi
Download Pdf Manuals
Related Search