LS8.0T Service Manual
Contents
1. amp 0 Mile on TIME window ENG 4 Information Accumulated Time and Distance Press and hold the START key for 5 seconds to clear all data Remarks Unit of Time is Hour Unit of Distance is KM or Mile based on your set SECOND LEVEL Software Version To Get to ENG 8 Enter into ENG 3 the press and hold the SPEED UP and INCLINE DOWN key at the same time for 3 5 seconds Press ENTER at PO Software version Press ENTER at P1 Select speed up rate normal or quick Press ENTER at Hold the START key to clear all data X START key to save the change Demo off console will display Figure A after remove the safety key Demo on 60 seconds later after remove the safety key the console will enter into DEMO ON MODE The LED and LCD will display in turns Figure B FIGURE A FIGURE B2. with a damp cloth Never use solvents as they can cause damage to the treadmill Inspect the power cord If the power cord is damaged contact Customer Technical Support Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut Check the tension and alignment of the running belt Make sure that the treadmill belt will not damage any other components on the treadmill by being misaligned any labels are damaged or illegible contact Customer Technical Support for replacements EVERY WEEK WEEKLY Clean underneath the treadmill following these steps Turn off the treadmill with the ON OFF switch then unplug the power cord at the wall outlet Fold the treadmill into the upright position making sure that the lock latch is secured Move the treadmill to a remote location Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill Return the treadmill to its previous position EVERY MONTH IMPORTANT Turn off the treadmill with the ON OFF switch then unplug the power cord at the wall outlet Inspect all assembly bolts of the machine for proper tightness Remove the motor cover Wait until ALL display screens turn off Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated Failure to do 50 may result in premature failure of key electrical components Vacuum and wipe down the b
3. 1 58 0 Service Manual TABLE OF CONTENTS CHAPTER 1 SERIAL NUMBER LOCATION 3 CHAPTER 2 PREVENTATIVE MAINTENANCE 2 1 Preventative 4 2 2 Tension and Centering the Running 6 CHAPTER 3 ENGINEERING MODE Ook ENON 7 32 Engineering Mode 0 0 0 pp 8 CHAPTER 1 Serial Number Location 1 1 Serial Number Location TM641 B 2KM 58 0 S N TM6411103BD00397 DESIGNED IN U S MADE IN CHINA CHAPTER 2 Preventative Maintenance 2 1 PREVENTATIVE MAINTENANCE Preventative maintenance is the key to smoothly operating equipment as well as keeping the user s liability to minimum Equipment needs to be inspected at regular intervals Defective components must be replaced immediately Improperly working equipment must be kept out of use until it is repaired Ensure that any person s making adjustments or performing maintenance or repair of any kind is qualified to do so AFTER EACH USE DAILY Clean and inspect following these steps Turn off the treadmill with the ON OFF switch then unplug the power cord at the wall outlet Wipe down the running belt deck motor cover and console casing
4. elt with a damp cloth Vacuum any black white particles that may accumulate around the unit These particles may accumulate from normal treadmill use CHAPTER 2 Preventative Maintenance 2 1 PREVENTATIVE MAINTENANCE EVERY 6 MONTHS OR 150 MILES It is necessary to lubricate your treadmill running deck every six months or 150 miles 240 kilometers to maintain optimal performance Once the treadmill reaches 150 miles 240 kilometers the console will display the message LUBE or LUBE BELT The treadmill will not operate while the message is showing Hold STOP for 5 seconds to suspend message for 5 miles Your treadmill came with a bottle of lubricant which can be used for two applications e Turn off the treadmill with the on off switch then unplug the power cord at the wall outlet e Loosen both the rear roller bolts for best results place two removable marks on both sides of the frame and note roller position Once the belt is loosened take the bottle of lubricant and apply it to the entire top surface of the RUNNING BELT RUNNING DECK running deck Tighten both rear roller bolts matching up the marks for proper position to original position After you have applied lubricant plug in the power cord insert the safety key start the treadmill and walk on the belt for two minutes to spread the lubricant e Lubricate the air shocks with Teflon based spray Once lubrication is comple
5. te reset the console by pressing and holding STOP and SPEED buttons for 5 seconds CHAPTER 2 Preventative Maintenance 2 2 TENSIONING 8 CENTERING THE RUNNING BELT you can feel a slipping sensation when running on the treadmill the running belt must be tightened In most cases the belt has stretched from use causing the belt to slip This is normal and common adjustment To eliminate this slipping turn the treadmill off and tension both the rear roller bolts using the supplied Allen wrench turning them turn to the right as shown Turn the treadmill and check for slipping Repeat if necessary but never turn the roller bolts more than 1 4 turn at a time Belt is properly tensioned when the slipping sensation is gone The running belt has been properly adjusted at the factory before it was shipped At times the belt can move off center during shipment Before operating the treadmill make sure the belt is centered and remains centered to maintain smooth operation If the running belt is too far to the right side With the treadmill running at 1 mph turn the left adjustment bolt counter clockwise turn at a time using the supplied Allen wrench Check the belt alignment Allow belt to run a full cycle to gauge II more adjustment is needed Repeat if necessary until the belt remains centered during use the running belt is too far to the left side With the treadmill running at 1 mph
6. turn the right adjustment bolt counter clockwise turn at a time using the supplied Allen wrench Check the belt alignment Allow belt to run a full cycle to gauge II more adjustment is needed Repeat if necessary until the belt remains centered during use Belt is too far to the left side CHAPTER 3 Engineering Mode 3 1 ENGINEERING MODE 1 To enter Engineering Mode press amp hold the INCLINE and SPEED DOWN keys at the same time for 3 5 seconds until Engineering Menu appears on the display 2 Use the INCLINE and SPEED UP and DOWN keys to select a parameter 3 Press ENTER to enter a parameter setting 4 Use the INCLINE and SPEED UP and DOWN keys to change the parameter 5 Press the START key to save the change to the parameter 6 Press and hold the STOP key to exit Engineering Mode and return to normal operation _ CHAPTER 3 Engineering Mode 3 2 ENGINEERING MODE OVERVIEW MODE FUNCTION DESCRIPTION ENG 0 Display Test Start Key LCD LED on Stop Key LCD LED off Any Other Key Will show on the display window Hold the STOP key for 3 seconds to return to the Engineering Menu ENG 1 Hardware Test Motor amp Incline Motor Test ENG 2 Auto Calibration Auto calibrates the speed only Switch Function Use the INCLINE or SPEED UP and DOWN keys to switch DEMO MODE off or on Demo on 1 amp Demo off 0 on DISTANCE window Use the START key to select unit 1 KM
Download Pdf Manuals
Related Search