xqb50-10 service manual
Contents
1. Check if the wire connecting Yes the computer board to the Replace the wire unit water level sensor is bad No Select 1 or 2 water level Yes It leaks gas Please check and and start the machine to repair the gas guide system check if the gas cell ds Please smear 801 glue in installation of the connecting d s Please smear 801 glue in installation of the gas cell cover No Yes Clear various factors like heck if ee Je eye the foreign Materials No Blow from the connecting pipe to the water level sensor and gas cell to see if there s blocking Replace the water level switch 14 H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 6 No spinning The washing and draining are normal heck the On Off point of the No On Off point Replace the microswitch microswitch and stop switch or stop switch Normally heck if the clutch paw No s pulled enough Replace the drain motor At this time please check if the drain motor is well i Replace the retarder clutch 7 Too much spinning noise e E Set the machine horizontally No If the hanger is Replace the hanger wrongly used No If the noise of the motor Yes Replace the motor oo much No f the motor is fastened No Fasten the motor tightly l No If the bearing of the retarder Replace the retarder is well 1 Yes Adjust the angle or the distance of ARE EUR a des the ratchet a2. ral of the system carefully If it is normal of the bearing part Not exist locking the clutch Measure the voltage of the Exist two ends of the motor Not exist lf the motor overheat protector acts Yes Please check the reason Measure the voltage of the two ends of the output of the computer sequence Exist No lf the capacitor has broke Replace the Not exist circuit or short circuit wire unit Replace the computer sequencer No Yes At this time please check if the capacitor and motor works normally Replace the motor Replace the Capacitor 13 H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 4 No draining Set rinse or spin Start the machine Roll up normall Check if the drain motor acts P y e En like No easure the voltage of the two ends of exis Replace the drain motor he drain motor No Exist Fhe two ends OF Re output Exist O e two en utpu 1 i of the computer Sequencer Replace the wire unit No Exist Replace the computer At this time check if the drain motor sequencer works normally 5 Keep filling water Open the water faucet without switching on the power porte aes a es Replace the vvater inlet valve No Switch on the power Do not push the Start Pause button ne i Replace the computer sequencer At this time please check if the No water inlet valve is well
3. Haier Automatic Washing Machine SERVICE MANUAL Models XQB50 10 O Features O 10 minutes QUICK WASH program 4 water level Spray current O Full plastic cabinet never rusts Special No SM XQB50 10 01 Edition 2006 7 18 H ale Automatic Washing Machine Model XQB50 10 Contents 1 CONTENTS 2 ree ce cec cee tee cee cee tee eee ana cee cee ans meses cas ee wee wee ee eee wee eee ee wee wee eee ee senses ses see 2 A 3 DECI CAOS OS 4 Safety precautions AN 5 Warning and cautions cec cec ecos ons see ene eee ona ces ens senses cesses EEE CEE CEE CEE CEE CEE CEE D 6 Net dimension css sense cesses cesses cesses essences cescesccesee o 7 Installation and accessory DAIS ess rer A sre nee erent EEE ea sees G 8 Parts and functions none cosoocooocooooocoocooccocooocoocoocoocoocooccoooooooocoooooocooooo ooooooooo 10 9 Maintenance service and trouble shooting sn see ses cee cee coe cee cee cee cee con cee cee ses cos es 11 10 Wiring diagram nn nos nos rrr rrr rrr rrr rrr rrr errr rr rrr rrr rrr rrr ere ere eee eee ee ee eee ee ee 17 11 Exploded VIRW2 EEE ces cce cee nos ons cee cesses cesses ces ses 18 12 List of parts AO H ale Automatic Washing Machine Model XQB50 10 Features Brand new appearance The model is novel and nice with full streamline curving shape to make the whole unit compact in structure 0 Music prompting It adopts the nationally originated music buzzer which will prompt you th
4. ater tap and washer H ale Automatic Washing Machine Model XQB50 10 Parts and functions Top lid B Toplid A gt Detergent box SS Lint filter Installed by user WSs E Control panel INS Ll 7 E Filter cover ANN Inner tub SS TA Control panel gt film Pulsator Cabinet Figure 1 base frame Adjustable foot Sop mat water valve Cabinet handle Drain hose Power line back cover Figure 2 3 H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 1 Trouble alarm and solve method Phenomena The reason How to settle Buzzing upon reservation starts The top lid is not closed e Close the top lid Nixie tube indicates EQ e ls the drain hose put down O Put down the drain hose Open No or slow drain nixie tube and close the top lid once indicates ET buzzing del bears ds Dy O Clean the foreign material ION Mela Open and close the top lid once Running pauses during spin nixie tube indicates E20 buzzing The top cover leaves open O Close the top lid Safety switch actuates not e Are the laundries put slantingly e Re order the laundries Close the spin after self correction top lid twice nixie tube displays Level the machine in right position e Is the machine slanting E3 buzzing Open and close the top lid once O The water tap is not open Open the water tap Push the START PAUSE button O The water inlet val
5. ctor elo a Orange Motor etractor O S trone Sensor Green Jlue D Figure 1 There is overload protector installed in the motor In case that the motor is overload or meets breakdown in working the protector will act and stop the motor When the breakdown is removed the motor will resume normal working O Actual Circuit Diagram E a SS SS A een ree ee ene ED ROE ee ene ee a a ee A A AA S A RA AASA SW EES 3 5 g 8 D S o G i 7 ME 2 y Control panel seat 3 IS D 8 Blue o LL GS 388 gg S2 a LS A ato a S 5 e amp Brown s White OIO gt Dn Computer sequencer T white ES E e amp Blue 2 H Blue Red NA T IN be zg Retractor Yellow LE RE Cabinet EE eee White 5 Motor o Red Blue Fuse g White S R Black Figure 2 ee dl
6. ding gt gt gt Builtunder OOOO EAN code o 6901570056449 S Energy efficiency class a Features for use OOOO Wash Capacity 5 Contral model A S contraer OOOO Normal computerized A Fuzzy computerized o e S G Frequency conversion SO Service features OO pq Programs o e S O Shorteyce OOO Inlet heating select Heating selection PP Spinning cycle selector OOOO Spinning cycle variable OOOO Start Pause OOO Automatic balning AO Aesthetics oo o S E Draintype direetiy drain drain down Door glass g plastic p ooo d e S Adjustablefeet pq Desiccaton O Airey A Drying A S D Technicaldata OO Voltage frequency Ov 60Hz Wash power W880 Spin power 20 Special function PP Air Bubble O Feet wheel pq Water fall current pq Dimensions measurements Width Pa 520 Depth with opendoor_______________ ____mm___ ___ 580 Dimensions packed measurements packed TI A 8B CA 5 Net weight S S kg Y B y Gross weight k S B 20 Containerload___________________ ___Sets ____80 40 Container load S ees ____4600 40HContainerload_______________ ___Sets___ ___ 460 Haier Please plug the plug on special 110V AC receptacle Please guarantee that the earthing wire is ear thed reliably Automatic Washing Machine Model XQB50 10 Safety precautions The power cord plug should be convenient to be pluged in or pluged o
7. e current mode during washing with sweet music O Low vibration and low noise the low noise retarder clutch motor and mute drain motor and the advanced air damping system can guarantee the washing machine operating under low vibration and noise O Automatic power off function If the washing machine is not started after the power is switched on or the washing Is finished the power will be switched off automatically after 5 minutes for the sake of safety O Alarm against breakdown the washing machine will alarm with abnormal display and buzzer when the drain hose is not put down or when top lid is open or the laundries are slanting during automatic program or spinning or when the imbalance can not be revised Automatic imbalance revising function during spinning if the laundries are slanting and bumping the tub the washing machine will add one rinse automatically to revise the imbalance O 10 minute quick wash program suitable for laundries less than 2 0kg please select this program to wash laundries with light dirt This program only costs 10 minutes for the whole washing procedure from water inlet wash rinse to spin 4 water level selection This machine offers 4 water level selection with lowest 20L level It can offer water levels corresponding laundries from below 1 0kg to 5 0kg It can save more water H ale Automatic Washing Machine Model XQB50 10 Specifications CAE A S New Model S XQBs0ut0 Freestan
8. intermittebtly 3 times 0 3s The WASH indicator flashes the STANDARD indicator is on Run washing with water for 5 minutes During washing you can change the current selection by The STANDARD indicator is on WASH and RINSE indicators flash Run spinning without water for 5 minutes The alarm during that procedure is the same as the program alarm in normal spinning program 11 H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 3 Trouble shooting charts lf you replace the computer sequencer without checking the other components carefully the computer sequencer may be damaged again Therefore please first check if the other components working normally before replacing the computer sequencer in maintenance 1 No action The indicator is off Confirm that there s no power failure and the power plug is inserted reliably The power switch is at On mode easure the voltage of the two ends of the power input of the sequencer Et Replace the sequencer Pull off the power Not exist plug Measure the resistance between the light blue wire terminal in the white plug on top of the wire uni and the N pin on the power receptacle Infinite Measure the resistance between the light blue wire termina in the red plug on top of the wire unit and the light blue wire of the lower part The resistance is O Infinite Replace the wire un
9. it easure the resistance between the brown wire terminal in the white plug on top of the wire unit and the brown wire of the lower part The resistance is O Replace the e de Infinite Check if the fuse is burnt Yes At this time please check if the other No Replace the fuse electric components work normally Check if the connection between the fuse and the wires of the two ends are well Replace the computer No sequencer Connect the fuse and the wires of the two ends Yes H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 2 No water filling Switch on the power Push the Start Pause button Confirm the action sound of the water inlet valve Exist Remove the foreign materials of the water inlet valve filter screen or raise the water pressure to 0 03Mpa 0 78MPa before use Not exist easure the voltage Exist of the two ends of the valvas Replace the water inlet valve ater inlet valve Not exist easure the voltage of the two ends of the omputer sequencer gt Replace the wire unit Replace the wire unit Not exist Replace the computer sequencer At this time please check if the water inlet valve works normally 3 No rotation in washing or rotate to one direction only Start the test without water Enter no water washing It acts Please check the transmission Check
10. n without care shall not use the machine To prevent your laundries and washing machine from damage be sure to take out all of the foreign materials from your pocket such as coins buttons sand or hairpins etc Cc Se P Automatic VVashing Machine D e Before washing please check if the water tap is open and if the water inlet pipe is connected properly e ltis suggested to use low foaming was hing powder Model XQB50 10 Warning and cautions Do not decompose repair or alter the machine by yourself Do not wash laundries with volatile materials such as thinner petrol etc A 5 FE 22 UA Keep the machine away from direct sunlight and heat source like the heater To prevent the lint in the tub from blocking the cascade outlet and influencing the cascade effect please keep the lint filter in good condition and install it to proper position during washing ty Put down Put up Haier Automatic Washing Machine Model XQB50 10 Net dimension UT Alo Mi NS Unit mm O I Figure 1 INSTALLATION AND ACCESSORY PARTS Please install and adjust the vvashing machine according to the requirement of this manual It is important for user s safe and proper using the machine Adjust the installation position The distance of washing machine to wall should be longer than 20mm The largest allowed slope of the base of the machine is 2 The slanting or rough ground will
11. nd pawl The distance is well P between the ratchet and the pawl is above 2mm No If the machine body Adjust the cabinet to acquire vibrate ESE with the balance No gt No If the balance ring is rubbing Yes Adjust the gap between the the outer tub cover balance ring and the outer tub Yes Fix the connecting pipe and the wire unit If the connecting pipe or the wire unit bumps the outer tub No The hanger seat is lack of oil Inject oil at the hanger seat 19 H ale Automatic Washing Machine Model XQB50 10 Maintenance service and trouble shooting 8 Too much noise in washing If the noise of the motor Yes is too much Replace the motor No If the motor fastened tightly Be Fasten the motor Yes The pulsator is rubbing the bottom of the inner tub Add pulsator gasket 16 H ale Automatic Washing Machine Model XQB50 10 Wiring diagram The capacitor coil L is used to protect the circuit please do not dismantle it Brown Blue Yellow Yellow Cover Switch pue Water Inlet Valve bray White E O gt a0 7 Red White EL ES Red White PIP switch Brown red g Blue o Black Red 2 Retra
12. result in unstable running or stoppage of the machine Please adjust it with following methods O Confirm it s horizontal Hang the lead line to confirm if it is horizontal H ale Automatic Washing Machine Model XQB50 10 INSTALLATION AND ACCESSORY PARTS e Adjust the adjustable foot 1 To twist the adjustable foot please first lift up the side of the foot slightly loosen the adjustable nut and twist the foot 2 Fasten the nut after adjustment How to change the direction of the drain hose 1 Lean the machine down gently with the 3 Extend the drain hose from the left side front surface facing the ground Push the drain hose into the groove with hands Push the drain hose into the groove with hands at this point 2 Pull out the drain hose from the right side groove Use this groove after direction changing H ale Automatic Washing Machine Model XQB50 10 INSTALLATION AND ACCESSORY PARTS Usage of the drain hose The drainage shall be smooth with the drain hose 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth enough and cause incomplete drainage 2 Do not tramp or press the drain hose 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly 4 1f extra drain hose is needed please make separate purchase The inner diameter of the extra hose
13. shall not less than 40mm and the length shall not exceed 1 5m lf the extra hose is too long cut it either at point Aor B H ale Automatic Washing Machine Model XQB50 10 INSTALLATION AND ACCESSORY PARTS Install the water inlet hose 1 Insert a new flat washer into each end of the inlet hoses Firmly put the washers in the coupling Note Use the new hose sets supplied with the washer Any other old hose sets should not be used e You may have to use pliers to tighten the coupling Do not over tighten because you may cause damage to the valve 2 Connect the water inlet hoses to the water faucet 3 Connect the other ends to their respective cold and hot water inlet valve located at the rear of the washer E of the water inlet hose Water absorption cushion Jointer of the water inlet valve 4 Fasten the nut Swing it gently to confirm if it s suitable Check the connection between the water inlet hose and the water tap 1 Swaying the hose gently to confirm if itis fastened Stable 2 After installation open the tap to check if it leaks 3 Do not bend the hose with overstrain 4 Before each usage please check if the connection between the water inlet hose and the water tap and the connection between the waterinlet hose and washer are firm soas to prevent dropping from improve Installation position Take down the water inlet hose 1 Close the water tap 2 Pulloff the water inlet hose from the w
14. ut with hand while the washing machine runs normally Be sure to pull the plug out and close the water tap when the machine is idle when moving the machine or when cleaning the machine Do not use wet hand to ins ert or pull out the power plug Do not bend extend twist bind by force Do not press or nip it with weight e Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully Do not put the machine at damp place like the bathroom Never wash it with water Do Not put wet laundries on the control panel In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet The ventilation holes at the bottom AO TOLD Q P SS Po SS AA AO OS ses ses soft items 9 Do not use water hotter above 50C Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning o Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any EN 9 Haier Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not let the children climb the washing machine Do not put any hot or heavy items such as the kettle with hot water the washing machine The handicapped or childre
15. ve is blocked Clean the water inlet valve Push the START PAUSE button O Wait for the normal water pressure before use e is there power failure O Use it when the power is on Notwash Is the power plug loose e Insert the power plug tightly The machine does e Does the water level arrive at e Affusion to the set water level AOtac the set water level O is the power plug loose e Insert the power plug tightly Not spin e ls the top lid closed e Close the top lid e Are the laundries put orderly e Put the laundries orderly No or slow water filling not reaching the level in 15 min nixie tube indicates E4 buzzing O The water pressure is too low and the current is too small There s abnormal sound inside the ls the machine slanting O Level the machine properly machine O Are the laundries slanting in e Re order the laundries spinning O s the jointer screw of the water Li The water faucet leaks inlet hose is loose or twisted sac ie Omer SETEN awry properly 2 Test program test without water Push and hold the PROGRAM SELECTION and PROCEDURE SELECTION buttons then push down the power switch to enter buzzer Test program Push the PROCEDURE SELECTION to select wash test program and spin test program N Buzzer test program Wash test program Spin test program The buzzer rings once All of the indicators flash After 3 seconds nixietube displays 88 all of the indicators flash and the buzzer rings
Download Pdf Manuals
Related Search