F5 Manual - First Watt
Contents
1. 1 KHZ noise versus frequency at 2 watts into 8 ohms 0 005 0 002 50 100 200 500 1k 2k 5k 10k 0 001 20 FIGURE 11 DISTORTION VS FREQUENCY 8 OHMS 2 WATTS Figure 12 shows the frequency response flat to DC and down 0 25 dB at 200 KHz E 3 20 100 200 500 1 2k 10k 20k 50k 200k FIGURE 12 FREQUENCY RESPONSE Figure 13 shows the square wave response at 200 KHz at 1 watt The amplifier is flat to DC and 0 25 dB at 200 KHz FIGURE 13 200 kHz SQUARE WAVE 1 WATT If you have the equipment to see it you may find that different gain devices will give you a small peak somewhere just below 1 MHz have found that you can trim this by playing with the values of R13 and R14 but as both values approach 0 ohms you are likely to see parasitic oscillations You can additionally limit frequency response with an input capacitor across R10 and also in the feedback loop with capacitance across R5 and or R8 As you can see have chosen not to Figure 14 shows the behavior of the amplifier clipping into 1 ohm at 10 amps FIGURE 14 CLIPPING INTO 1 OHM 25A SLOW E SWITCH FIRST WATT PS R1 POWER SUPPLY Ana G COPYRIGHT 2005 GENERAL AMPLIFIER ee ae RESISTORS ARE 47 OHM 3W Lene CAPACITORS ARE 15 QQUF 25V RB THERMISTORS ARE CL6Q TYPE a Ww AC LINE UNLESS NOTED2. 20v g 7 120 k _ C3 _ C4 _ C7 _ C8 Ag an TH Fa P T ANN 18VAC eva 0033 LINE 120 VOLT o 1 25A SLOW 3AG g 200V 7 R3 NNA J eae eee ee S ee R10 AAV 2 2K 3W i TH 24 VOLT 4 Thermistors in series with the AC line are also used to select line voltages at 120 VAC or 240 VAC as seen on the front edge of the PC board layout CHASSIS GROUND Copyright 2008 First Watt www firstwatt com
3. If you need to turn the gain up on your preamp then do so If you can t get enough gain then you are probably using either the wrong speaker or the wrong amplifier Talk to your dealer if this is the case The power supply of the amplifier is isolated from the chassis and AC earth ground by a thermistor which connects the circuit ground to the chassis and earth ground This helps to prevent ground loops but the thermistor stands by to conduct AC line voltage to ground until the fuse blows in case of transformer or other such failure The input impedance is 100 Kohms and the input capacitance is very low so you should find it easy to drive with tube equipment if you like The amplifier is largely indifferent to the source impedance of your preamp so a high source impedance is not a problem The amplifier requires about 1 hour of operation to reach normal operating temperature and this warm up time is appropriate for the most critical listening but is not otherwise an issue The amplifier s final adjustments were made after a 2 hours and the performance difference between that and cold operation is significant do not personally see a reason to run the amplifier all the time but you can do that if you want to The power supply capacitors are likely to last about 15 years or so and while they will slowly dry out just sitting there they will have a shorter life span with the amplifier running constantly Also at 180 watts it makes
4. AF s NCH 10K PREAMPLIFIER POWER AMPLIFIER E FIGURE 3 COMMON SOURCE EXAMPLES On the left you see an example of a simple preamplifier stage with a gain of roughly 10 times 20 dB The JFET is self biased in this circuit With 5 mA going through the JFET the gate needs to be at about 25V with respect to the Source We put 47 ohms in series with the Source raising its voltage to 25V and this conveniently allows us to bias the Gate at OV DC or Ground On the right we have a power MOSFET set up as a simple power amplifier intended to deliver about 1 watt into an 8 ohm loudspeaker The 16 ohm power resistor performs as a current source to the circuit and the two 10 Kohm resistors on the input set the DC value for the Gate to about 4 volts get it to conduct a 1 amp bias current For a more powerful version of this see Zen Variations 1 AudioXpress March 2002 Figure four shows some real Common Drain amplifiers a line level buffer which can be used in active filters and a headphone amplifier In both cases there is no voltage gain in the amplifier but there is current gain They both have high input impedance and low output impedance 10K 10UF 1K _ IRF240 1UF a G is NSR H bu gt leae 220 20V 16V Jog qur Z 8 OHMS 100K 1K 47K 16 BUFFER HEADPHONE AMPLIFIER FIGURE 4 COMMON DRAIN EXAMPLES Common Gate operation is encountered less often usually found in cascode connection with another
5. R16 respectively The resistance of the thermistor declines with temperature and if placed in close proximity to the output transistors will help compensate for thermal drift You can build the amplifier without them but you will have a longer warm up time and you will spend more time adjusting the bias On the positive half of the output stage Q5 R17 R19 and R21 will arbitrarily limit the output of the amplifier in the event that you accidentally set the bias too high or short the amplifiers output Q6 R18 R20 and R22 do the same for the negative half of the amplifier The output MOSFETs are easily capable of passing very high currents at the request of Q1 and Q2 and it is wise to set a limit in case of accident Understanding the limiting circuit is easy Q5 and Q6 look at the voltages across the R11 and R12 and will start to conduct when their Base to Emitter voltage exceeds 4 volts or so At 4 volts Q5 and Q6 draw off enough drive current from Q1 and Q2 to start creating measured distortion and hard limiting occurs when the voltage driving Q5 or Q6 is increased to 6 volts Since the 1 3 amps bias through the 47 ohm Source resistors provides at 0 6 volts already we have to divide that voltage down so that limiting occurs at a higher current We do this for Q5 with divider resistors R17 and R19 and for Q6 with R18 and R20 R21 and R22 allow us to also adjust the limit point based on some information from the output voltage Where
6. connections to the loudspeakers are made through the gold plated brass 5 way connectors The red top connection is positive and the black bottom is negative In this amplifier the black banded output connectors are connected directly to signal ground A caveat is in order here this is a very wide band amplifier with a high input impedance In order to prevent the output voltage from bleeding back to the input at very high frequencies thus making a fine power oscillator keep the input and output cables separate and don t externally connect the speaker ground to the input ground Good ground shielding on the input cables is important and caution is called for in using Litz and other specially low inductance high capacitance cables have not seen a specific example of a problem but historically it is to be expected when an amplifier s bandwidth exceeds 200 KHz If the amp makes funny noises runs extra hot or blows fuses this might be an indicator of such an issue If you have any questions just drop me an email nelson passlabs com With everything connected up and the source equipment powered up first you can proceed to turn on the power switch to the amplifier Turn on and turn off thumps and noise are small in this amplifier and should not present any hazard to delicate drivers At this point you should be able to listen to music This amplifier has less gain than most 15 dB but at 25 watts it s not likely to need it
7. descending to 001 below 1 watt 10 5 2 1 0 5 0 2 0 1 0 05 0 02 0 01 0 005 0 002 0 001 0 0005 0 0002 0 0001 100m 200m 500m 4 2 5 w FIGURE 7 DISTORTION VS POWER 8 OHMS 1 KHZ 10 20 Figure 8 spectrum distribution of the distortion at 1 watt and you can see the dominant 3 harmonic as well as 2 4 and 5 The vertical scale is in decibels relative to 1 watt In this picture you can also see the noise floor of the system and amplifier at 135 dB or so below 1 watt 90 dB 100 dB 110 dB 120 dB TN 130 wl La arae ie noes ee Oa OD AAO 2K 3K 4K 5K 6K 7K 8K 9K FIGURE 8 DISTORTION SPECTRUM 1 WATT 1 KHZ Figure 9 shows the harmonic distortion noise plotted against output power 4 ohms load reaching 0 2 at 40 watts 0 05 0 02 0 01 0 005 0 002 0 001 0 0005 0 0002 on 10 0 5 0 2 0 1 001 100r 200m 500m 1 2 5 10 5 2 1 20 w FIGURE 9 DISTORTION VS POWER 4 OHMS 1 KHZ Figure 10 shows the harmonic distortion noise plotted against output power into 2 ohms where the amplifier begins to clip at 0 3 at 50 watts Figure 11 shows the distortion 10 0 01 2 5 10 20 50 w FIGURE 10 DISTORTION VS POWER 2 OHMS
8. for the N channel parts Q1 and 2SJ74 or 2SJ108 for the P channel parts Q2 In these cases the Idss selection code is BL although V and GR types will also generally work fine The primary thing about these particular parts is the transconductance figure of 20 mS many of the potential substitutes are much lower at 4 to 10 mS The output MOSFETs are the IRF240 N channel type Q3 and the IRD9240 P channel type Q4 They will want to have a voltage rating in excess of 50 volts a current rating of about 15 to 20 amps and a dissipation of about 150 watts Comparable parts are widely available and here used Fairchild FQA12P20 and FQA19N20C The remaining parts can be generic or special as you see fit used Dale RN55D type watt resistors and the 3 watt Panasonic power resistors from Digikey where you can also get the 4 7 Kohm thermistors and trim pots Audiophiles are often concerned about the effects of capacitors in audio circuits but a quick examination of the schematic will put your concerns to rest Power Supply The power supply of the tested amplifier is 24 volts and should be rated at 6 amps continuous duty and more than 10 amps peak per channel Ordinary unregulated supplies will work fine and if you need suggestions the Zen Variations 5 AudioXpress October 2003 and Zen Variations 3 AudioXpress August 2002 both have good examples of regulators and the raw supplies that feed them recommend rail voltages from 2
9. sine wave is that the peak wattage is twice the average so this circuit would operate 27 watts average Class A into 8 ohms At currents above 2 6 amps one of the transistors will shut off leaving the other to continue to increase beyond the 2 6 amps in what is known as Class AB This circuit employs feedback to improve the performance in a number of ways Feedback sets the gain lowers the distortion improves the bandwidth and creates the output impedance damping factor of the amplifier The feedback mechanism for this amplifier is R3 through R6 a dual pair of low impedance voltage dividers which feed the output to the Source pins of Q1 and Q2 Low impedance feedback has been incorrectly referred to as current feedback and it is popular in simple high speed linear circuits One of the charms of this arrangement is that unlike the classic two transistor differential pair the drive current available exceeds the bias of the input stage Something different about this example is that each JFET has its own feedback there are two separate feedback loops to this amplifier so that the loop of Q1 Q3 is independent of the loop for Q2 Q4 The circuit of Figure 5 illustrates the basics and does in fact work but has a tendency toward instability Local parasitic oscillation is often seen and the bias drifts with temperature requiring a lengthy adjustment period This simplified circuit also has no provision for adjusting against the var
10. the pipe as wire and the tank of water as a battery or even a charged up capacitor d In FIGURE 1 FET TRANSISTOR VERSUS WATER FAUCET To continue the metaphor the voltage of the supply is the water pressure and the water flowing from the supply is the electrical current The Source S connection of the FET is the output of the faucet The Gate G of the FET is the control pin and like the handle on the faucet it controls the amount of electrical current through the FET from the Drain to the Source For the FET this control is a function of the relative voltage between the Gate and Source pins For an N channel FET raising the Gate positively with respect to Source increases the current flow Yes know some of you are thinking that maybe the Source should be on top and the Drain on the bottom but they re not You might not want to call a quantum mechanic if your plumbing stops up The idea that the current going through FET transistor is controlled by the voltage between the Gate and the Source pins remains the key idea and if you have that firmly fixed we can leave the waterworks metaphor behind FETS come in different types There are two polarities N channel and P channel There are different voltage current and power ratings and different semiconductor processes resulting in JEETs and MOSFETs In all of them the current from the Drain to Source is controlled by the voltage between Gate and Source A FE
11. 3 to 25 volts Heat Sinking At 1 3 amps per channel you will see idle heat dissipation of 62 watts To keep the temperature rise of the heat sink to 20 deg C above the ambient temperature you will want a heat sink rated at about 6 deg C watt for each transistor An example of this would be a chunk of finned aluminum with a series of 2 fins attached to an 8 by 6 base You will need two per channel The output devices need to be intimately attached to the heat sink The mounting surface on the heat sink should be at least inch thick and smooth and shiny You can use silicone pads for insulation but Mica and silicone grease are the best Initial Adjustment Before applying power to the amplifier you will want to set the values of P1 and P2 to their minimum Verify this with an ohmmeter When it comes times to fire up the amp first time if you have a Variac use it fusing the AC line to the amplifier with a 1A fast blow fuse Turn the Variac up slowly and if you haven t popped the fuse then go ahead and confirm the rail voltages to the channels Each channel does not need to be attached to a load in order to adjust it If the only load you have is the loudspeaker would advise against using it during adjustment For each channel you will be adjusting P1 and P2 alternately in order to achieve 0 volts DC at the output and 59 volts across R11 and R12 Each time you adjust P1 you will probably have to go back and adjus
12. First Watt model F5 Operation and Service Manual So far First Watt has made a few different amplifiers Very different amplifiers Quite a few people have asked me for a regular sort of amplifier you know the kind you plug like any other with some voltage gain and a real damping factor Amplifiers that have low distortion and noise and will drive a 4 ohm load The last time people asked for that they got the Aleph J which satisfied most of those requirements Single ended Class A the Aleph J is an easy going design which is happy driving 8 ohm loads with a warm relaxed presentation By way of contrast present the F5 taa daa a push pull Class A amplifier utilizing JFETs and MOSFETs in a very simple two stage complementary circuit a little bit like a complementary version of the Aleph J But like all the other First Watt amps so far this one is different In many ways it s an ordinary topology the basic circuit is found in numerous preamp circuits and the odd power amplifier Check out the Profet amp from Selectronics But the F5 is the product of numerous decisions that set it apart It has very wide bandwidth DC to gt 500 KHz No capacitors anywhere in the circuit except in the power supply of course It has a high input impedance 100 Kohms and a high damping factor 60 The distortion is very low between 001 and 005 at 1 watt It s very quiet about 60 microvolts or so It will drive a 2 ohm load w
13. S The optimum bias values vary by the device and the needs of the circuit In general to function as an amplifier the FET needs to have a least a few volts between the Drain and the Source If the FET is an N channel type the Drain must be at least a few volts positive with respect to Source If it s a P channel type the drain must be negative with respect to Source In addition the Gate of the FET must be placed at a DC value relative to the Source so that the current and voltage of the FET is positioned in the linear region between the extremes of voltage and current somewhere between all the way on and all the way off It is in the middle ground where the distortion is low Generally for N channel JFETs it is with the Gate voltage at 0 or slightly negative with respect to the Source and for N channel MOSFETs the gate voltage is a couple volts positive One of the important functions of a circuit is to set up the DC conditions of gain stages so that the devices have stable operation in this region For every amplifying circuit there will be a sweet spot of voltage and current which will give the best overall performance Figure three shows some examples of real circuits that illustrate simple Common Source amplifiers and the bias voltages and currents that would be typical for them You can build both of these circuits and they will work 24V 16 a our 10K fe jk 1OUF 1000UF F F240 SOUNS
14. T is a three pin device and there are three ways to amplify with them Figure 2 illustrates these with an N channel FET Common Source CS is the connection which can give us both voltage and current gain in a circuit The input voltage shown as a little graphical sine wave goes to the Gate and the output is taken from the Drain and appears across a resistor between the Drain and the supply voltage The Source is grounded and doesn t show a signal voltage and that s why it s called Common Source Note that the output voltage is inverted in phase from the input voltage Common Drain CD gives current gain only and is also known as Source follower because the output voltage across the Source resistor is nearly identical to the input voltage at the Gate While the Drain is usually attached to a DC voltage value the AC voltage is ideally zero and so it is called Common Drain Common Gate gives non inverted voltage gain only with the input signal going into the Source and coming out the Drain The Gate is grounded Figure 2 only shows what happens to AC signals but it doesn t illustrate the DC voltage and current values that the FETs need in order to operate These DC values are often referred to as the bias of the device and you will hear that word a lot with respect to amplifiers D IN jae alt IN oa S OG Aave s COMMON SOURCE COMMON DRAIN COMMON GATE FIGURE 2 THE THREE OPERATING MODE
15. d the possibilities of current source operation with single stage Class A circuits and no feedback The Aleph J used JFET devices for the front end of a two stage single ended Class A amplifier The F3 achieved very low distortion using power JFETs in a single stage single ended Class A circuit The F4 demonstrated that an amplifier did not necessarily require voltage gain to be useful You can follow the progression at www firstwatt com Here is the F5 We want to further push the performance boundaries of simple little amplifiers with a FET two stage Class A push pull design A Quickie Tutorial on FET Amplifiers One of the aims of these articles is to get people to build amplifiers so here is some tutorial material to get beginners going have written up some of this material before The A75 Audio Amateur 4 1992 but that was 15 years ago and maybe it will be helpful to repeat bits of it All 31 years worth can be found at www passdiy com and related links I m assuming that you understand the concepts of voltage current and resistance If you already know how a FET works you can skip ahead Figure 1 shows an N channel FET a quantum mechanical black box with three connections This device is meant to function as a valve a little bit like a water faucet In this picture the Drain D of the FET is attached to an electrical power supply analogous to the pressurized water supply on the other side of the faucet You can imagine
16. device Discussions of cascoding with good examples are found in Zen Variations 8 and 9 AudioXpress January 2006 May 2006 and also the article Cascode Amplifiers originally published in Audio Magazine March 1978 Simplified F5 Circuit Figure 5 shows the simplest imaginable version possible of the F5 The topology is familiar a two stage conjugate complementary circuit using two JFET transistors for the input amplification and two power Mosfet devices for the output lt IN aa OUT Qz aS Q gt ass R6 50 12 so G Q2 E p FIGURES SIMPLIFIED CIRCUIT JFETs Q1 and Q2 form a complementary Common Source stage with the input appearing at their Gates and output at their Drains The JFETS are Class A self biased at about 6 mA and so a current 11 comes out of their Drain connections and creates a voltage of about 3 6 volts across R3 and R4 whose values are about 600 ohms This 3 6V DC value is necessary to bias the power MOSFETs Q3 and Q4 into conduction The voltage gain of Q1 and Q2 appears across each of these resistors for a gain of about 10 each The gain of 10 for the input stage comes from the ratio of the 600 ohms divided by the apparent resistance from the Source to Ground which is roughly 60 ohms This 60 ohm number comes from the inverse of the JFET s transconductance plus the 10 ohm actual resistor The transconductance for a JFET is the ratio of current change against in
17. do we want to limit The amplifier with 24 supply rails should be good for a 50 watt peak into 8 ohms or about 2 5 amps For a 4 ohm load we would want 5 amps and for a 2 ohm load we want 10 amps Since we only have two output devices we probably are best off stopping there We will calculate the values as follows starting with arbitrary values of 1 Kohm for R17 and R19 At 10 amps peak the voltage across R11 or R12 will be about 4 7 volts R19 and R21 will be chosen to divide that down to 6 volts and we solve the formula 6V 4 7V R19 R17 R19 Since R17 is already 1 Kohm we simplify to 127 R19 1000 R19 And we get R19 150 ohms 10 amps into a dead short is about 200 watts dissipation on an output transistor which will probably exceed its rating R21 adds a foldback characteristic to this so that the current value will be lower into a shorted output To ensure against damage into dead shorts we want to limit the zero crossing current to about 5 amps keeping the dissipation just this side of destruction Current limiting gets a bad rap in general but think its a matter of where and how the limits are set If you build this amplifier you are of course welcome to delete this portion of the circuit and of course you will not complain if a shorted output lets the smoke out of your amplifier As it is you will still be taking some chances with a shorted output Part Selection The input JFETs used are 2SK170 or 2SK370
18. economic sense to shut the amplifier off if you aren t planning on using it for the rest of the day Again the heat sinks on this amplifier run fairly hot and you want to make sure that they get adequate ventilation They will run at around 25 degrees C above the ambient temperature which puts them around 50 degrees in the average listening room At this temperature you should be able to put your hand on them for about 5 to 10 seconds or so Now the following is for your protection Do not defeat the AC line Earth ground connection on the amplifier power cord It provides an extra barrier to prevent potential shock hazard Do not replace the fuse with a type other than specified Do not operate the amplifier outside in the weather or in and around water or anything resembling water If you spill a drink in the amplifier or if your dog cat child urinates on it turn it off immediately unplug it and do not operate it until cleaned by a qualified technician If something gets loose or rattles around inside or smells funny or if you can t touch the heat sinks for 5 seconds or so then turn it off unplug it from the wall and contact First Watt There are no user serviceable parts inside Do not open the amplifier and if you do anyway don t operate it with the cover off There are hazardous voltages inside If you need to change the operating AC voltage contact First Watt If you have a problem contact First Watt We are
19. iations to be seen between real FETs that you will encounter Actual Working Circuit Figure 6 shows a completely functional version of the circuit with useful enhancements We have added R7 and R8 in parallel with R5 and R6 so as to share the dissipation allowing inexpensive 3 watt resistors to do the job You never know what the amplifier will be attached to so the input of the amplifier now sports R9 to avoid parasitic oscillation of the input JFETs and R10 to ensure that the input has a default reference to ground when there is nothing connected R11 and R12 are 3 watt power resistors added to the Source pins of the MOSFETs to increase thermal stability and serve as convenient current sensing elements R13 and R14 are placed in series with the Gates of the MOSFETs to prevent parasitic oscillations just as we did with R9 on the input stage R 6 V paad OUT ry 0 6 V 4 nee 24V V FIGURE 6 F5 AMPLIFIER R2 and R4 have had their value increased and then placed in parallel with 5 Kohm trim potentiometers P1 and P2 This allows adjustment of the output stage bias current and also the output DC offset We can stop here and the amplifier will be fully functional The remaining additions will enhance temperature tracking and provide for output current limiting Th1 and Th2 are small 4 7 Kohm thermistors that have been placed in series with R15 and
20. ithout burping and 1 ohm without misbehaving Did mention that it sounds terrific So enjoy In addition to the normal owner s manual information have appended the original DIY F5 article which appeared in AudioXpress Nelson Pass 5 24 08 Setup The initial setup of the amplifier is very straight forward Place the amplifier in a well ventilated location as it draws about 180 watts during operation and requires as much opportunity to cool itself as possible You should be able to put your hands on the heat sink during operation If you can t do this for 5 seconds or so they need more ventilation On the front panel there are two blue LED lights one for each channel indicating power to the channel On the rear panel you will find a pair of RCA inputs speaker outputs a fuse holder an AC power receptacle and on off switch The label will indicate a serial number and also what AC line voltage the amplifier is set for If the voltage is 120 VAC then the fuse value will be a 3AG slow blow fuse rated at 2 5 amps If the voltage is 240 VAC then the fuse will be rated at 1 25 amps Do not substitute a larger value fuse Contact First Watt if you have any questions I m assuming that you know how to attach the speaker cables to the 5 way output connectors provided Please make all the connections with the amplifier power switch in the OFF position For two channel operation input signal is connected to the RCA inputs The output
21. much happier helping you solve problems so that we can be certain that it s done properly If you are far away and don t want to ship the product for repair we will assist your technician with information and parts Contact www Firstwatt com nelson passlabs com Summary of the nominal specifications Measured at 120 V AC with a 25 ohm source and an 8 ohm load Distortion 1 watt 001 to 005 1 KHz Input Impedance 101 Kohm Damping Factor 60 Output power stereo 8 ohms 25 watts 1 THD 1KHz Voltage Gain 15 3 dB Maximum unclipped output 20 Volts Maximum output current 10 amps Frequency response 0 dB DC 3 dB 1 megaHeritz Noise 60 uV unweighted 20 20 KHz Power consumption 180 watts Fuse 3AG slow blow type 2 5 Amp for 120VAC 1 25 Amp for 240 VAC Warranty Parts and labor for 3 years not covering shipping costs or any sort of consequential damages Warranty coverage is voided for modified products and repair of modified products is at our discretion Copyright 2008 General Amplifier General Amplifier Inc PO BOX 7607 RENO NV 89510 7607 www firstwatt com F5 Power Amplifier As printed in AudioXpress May 08 Nelson Pass 1 31 08 Intro As many of you may know First Watt is dedicated to exploring the performance quality of small simple power amplifiers Over the past four years five such amplifiers have been designed as concept pieces and produced in limited quantities The F1 and F2 explore
22. put voltage change The gain of this part is typically 0 02 Siemens or 02 amps per control volt and if you invert that you get 50 ohms R V I So it looks as if there is 50 ohms inside the part although there isn t and to that we add the 10 ohms of real resistor to get 60 ohms Q3 and Q4 do the heavy lifting in this circuit providing the large output current needed to drive the loudspeaker The DC voltage appearing from the Gate to Source of these devices is about 3 6 volts and this biases the MOSFETs to about 1 3 amps For this sort of circuit a 1 3 amp bias means that the amplifier will operate Class A to 2 6 amps of output current To understand this imagine a condition where Q3 and Q4 are idling at 1 3 amps so that all the current is going from the V voltage rail to the V voltage rail and none is going through the loudspeaker When a positive voltage appears at the Gates of Q1 and Q2 it makes the current through Q1 increase and the current through Q2 decrease The resulting voltages across R3 and R4 make the current through Q3 increase and the current through Q4 decrease This makes the output voltage go positive As the positive input voltage increases you approach the point at which Q3 is conducting 2 6 amps and Q4 is conducting 0 amps and all of the 2 6 amps goes through the loudspeaker The power of 2 6 amps into 8 ohms is 1 2 R or 2 6 2 6 8 54 watts This is the peak value and the nature of an undistorted
23. t P2 again and so recommend adjusting the pots in half measures alternately setting the pots half way to their voltage goals and measuring the DC values Unless there is something very wrong when the output is at 0 V DC the values across R11 and R12 will be equal In spite of the thermal compensation in the circuit you should assume that there will be drift as the heat sink temperature rises and you will need to readjust the values over the course of an hour or two Usually it is best to start out bias adjustment low at maybe 0 4 mV across R11 and R12 until the amp is warmed up a bit You should be able to get the output DC offset down to 10 mV or so and would consider 50 mV the highest acceptable figure for this amplifier when warmed up After the amplifier has been operated for a few weeks it is a good idea to check and adjust the offset again after the parts have been burned in Measured Performance The gain of the circuit is 15 15 dB The input impedance is 101 Kohm and the output impedance is 0 1 ohms for a damping factor of 80 The noise of a properly laid out circuit is about 30 uV with a quiet supply and raw supply with two 29 000 uF capacitor and 70 mV ripple will give about 100 uV noise measured in the band from 20 to 20 000 Hertz Figure 7 shows the harmonic distortion noise plotted against output power taken at 1 KHz into 8 ohms This is the lowest distortion yet achieved by either a Zen or First Watt amplifier
Download Pdf Manuals
Related Search